T H E S O U N D T H A T C R E A T E S L E G E N D S
KEYBOARD
EXTENDED
RANGE
Two hundred
,
OwnersManual
P/N 048502
Download from Www.Somanuals.com. All Manuals Search And Download.
A
D
E
F
B
C
CHANNEL 1
CHANNEL
SEND
INPUT
VOLUME
5
LOW
0
MID
0
HIGH
0
INPUT
VOLUME
5
LOW
0
MID
0
EFFECTS
5
REVERB
5
0
10
-12 +12
-12 +12
-12 +12
0
10
0
10
0
10
-12 +12
-12 +12
CHANNEL 3
SEND
INPUT
VOLUME
5
LOW
0
MID
0
HIGH
0
VOLUME
5
LOW
0
INPUT
MIC
EFFECTS
5
REVERB
5
0
10
-12 +12
-12 +12
-12 +12
0
10
0
10
0
10
-12 +1
G
KXR 2 0 0 FRO N T PAN EL FUN CTIO N S
A. CHANNEL 1 INPUT (1/ 4 INCH) - Plug-in connector for
instruments. This balanced input can handle as much
as 8V R.M.S.
external effects device. The effects send control in con-
junction with the effects send jack could be used to
drive another KXR 200 as a slave amp. This is done
by connecting the effects send jack, with a standard
guitar cord, to the effects return jack of another KXR
200. Note that each channel could be set to send a
different amount of signal to the effects bus.
B. CHANNEL 1 VOLUME CONTROL - This control adjusts
the preamplifier gain of channel 1. It works in con-
junction with the Master Volume control ( item I) to set
the overall loudness of the amplifier for channel 1
only. Being a true “gain” control, it allows for the use
of a variety of microphones, keyboards or other instru-
ments with differing output signal levels. Low-level
instruments generally require a higher Channel
Volume setting while “hotter” keyboards will require a
lower setting.
E. CHANNEL 1 REVERB SEND CONTROL - This control
works in conjunction with the reverb return control
(item K) to allow the amount of reverb to be mixed
with the dry signal. The amount of reverb-sent signal
is independent for each channel.
F,G. CHANNEL 2 AND 3 - These two channels are provid-
ed for two additional instruments. All the controls and
jacks operate in the same manner as those in channel
1. When not in use, it is best to turn the channel vol-
ume, the effects send and the reverb send controls all
the way down to avoid any amplification of unwanted
noise. Likewise, when not in use, the equalizer sec-
tions should be kept flat ( i.e. all knobs should be set at
12 O’clock).
C. CHANNEL 1 EQUALIZER - This equalizer allows
adjustments of the tonal characteristics of channel 1
before amplification. Each control provides a 12dB
boost or cut to bands of frequencies centered about
130, 540, and 4200 Hz. Note that all equalizer sec-
tions of the KXR 200 are designed so that if all center
frequencies are set at +12dB, a flat overall response
would be obtained. This is very useful if the signal
source is weak.
H. CHANNEL 4 - This channel operates in the same man-
ner as the other three channels, but with the addition
of a few extra features: The XLR jack and an extra
band in the equalizer section. With the vocalist in
mind, the balanced, low impedance XLR jack provides
a suitable connection for a microphone. Furthermore,
the four-band equalizer was designed around the
D. CHANNEL 1 EFFECTS SEND CONTROL - This control
works in conjunction with the effects send jack (item R),
effects return jack (item S), and the effect return con-
trol (item J) to , respectively, allow a desired amount of
preamp signal to be massaged, and to control the
amount of return signal that has gone through an
Download from Www.Somanuals.com. All Manuals Search And Download.
L
I
J
M
F
K
CHANNEL 2
MASTER
RETURN
ON
SEND
EFFECTS
LOW
0
MID
0
HIGH
0
VOLUME
5
REVERB
5
EFFECTS
5
REVERB
5
5
ON
OFF
-12 +12
-12 +12
-12 +12
0
10
0
10
0
10
0
10
0
10
DELTACOMPTM
CHANNEL 4
LOW MID
0
POWER
SEND
VOLUME
5
LOW
0
HIGH MID
0
HIGH
EFFECTS
5
REVERB
5
KEYBOARD
EXTENDED
RANGE
0
0
10
-12 +12
-12 +12
-12 +12
-12 +12
0
10
0
10
Two hundred
N
O
H
vocal frequencies. With each control providing 12dB
of boost or cut, and centered about 125, 320, 1000
and 3200 Hz. If needed, this channel could also be
used for another instrument.
L. PEAK LED INDICATOR - This LED comes on when
excessive signal levels are being sent to the power
amplifier. It illuminates on signal peaks that cause
clipping (distortion) with DELTACOMPTM not activated,
or for signal peaks that cause DELTACOMPTM to reduce
level (DELTACOMPTM active). If the limiter is on for a
large percentage of the time, the dynamic range of the
system is reduced and the overall sound suffers. For
this reason, level controls should be adjusted so that
the yellow LED only flashes on occasional signal
peaks.
I. MASTER VOLUME CONTROL - This control adjusts the
level of the signal coming out of the preamplifier sec-
tion. This control is used in conjunction with the
Channel Volume controls to set the overall sound level
of the amplifier. In order to maximize headroom and
minimize noise, instruments with low-level output will
require a high Channel Volume setting and a low
Master Volume setting, while other instruments may
require a lower Channel Volume and higher Master
Volume setting. It is recommended that the Master
Volume control be set as high as possible for maxi-
mum DELTACOMPTM compressor range.
M. DELTACOMPTM SWITCH - This switch is used to activate
or de-activate the DELTACOMPTM circuitry. If peak-
clipping of signal is not desired, then the
DELTACOMPTM circuitry should be engaged by push-
ing this button in.
J. EFFECTS RETURN CONTROL - This control adjusts the
level of the signal coming into the power amplifier sec-
tion from external effect devices. This is the master
control for all the Channel Effects Send controls. If not
in use, it is recommended that this control be set at 0
to avoid amplification of any unwanted signal.
N. POWER LED INDICATOR - When this LED is illuminat-
ed, the KXR 200 is receiving power.
O. POWER SWITCH - This switch turns the KXR 200 on or
off. When the switch is off, the amplifier is completely
shut down.
K. REVERB RETURN CONTROL - This control adjusts the
level of the reverb signal coming into the power ampli-
fier from the reverb bus. The input to the reverb cir-
cuitry is the sum of the individual channel reverbs.
When not in use, it is recommended that this control
be set at 0 to avoid amplification of any unwanted sig-
nal.
Download from Www.Somanuals.com. All Manuals Search And Download.
KXR 2 0 0 REAR PAN EL
LINE OUTPUT JACKS - Signal from each of the chan-
P,Q.
nels are combined with reverb and effects to form the
input to the power amplifier stage. The Line Outs are
wired from this point. The 1/ 4 Jack (Item P) and the
XLR jack (Item Q) provide easy connection paths from
the KXR 200 to any external devices, such as a slave
amp or a mixer. It is also useful for recording live per-
formances. Note that inserting a plug into one of the
Line Outs jacks does not interrupt the normal internal
signal flow of the KXR 200.
POWER CORD - This amplifier is equipped with a
grounding type supply cord to reduce the possibility of
shock hazard. Be sure to connect it to a grounded AC
receptacle. The line cord should be connected to a
suitable power source, in accordance with the voltage
and frequency as shown by the power rating on the
rear panel. DO NOT ALTER THE AC (MAINS) PLUG.
NOTE: DO NOT BLOCK THE AIR FLOW TO THE
REAR PANEL; FOR EXAMPLE, BY BACKING THE
AMPLIFIER UP AGAINST A WALL. The rear panel
contains a heatsink that needs air flow to cool off the
amplifier. Blocking the air flow may result in equip-
ment failure due to excessive heat building up inside
the chassis.
EFFECTS SEND JACK - This jack is the output of the
effects bus, where all the channels Effects Send are
combined. The signal coming out of this jack could be
used to drive an effects device, a slave amp, or as an
input to a mixer . Note that the signal coming out of
this jack is reverb-free.
R.
S.
T.
EFFECTS RETURN JACK - This jack inputs signal to the
master section of the KXR 200 through the Effects
Return control (Item J). This jack can be used with the
Effects Send Jack (item R) as a patch point for mono
effect devices. This jack can also be used as the input
jack when the KXR 200 is used as a slave amp.
WARNING : THIS EQUIPMENT MUST BE EARTH
GROUNDED.
COVERING CARE - UNPLUG THE POWER CORD
BEFORE CLEANING - The exclusive vinyl covering on
your cabinet has been especially designed for years of
lasting beauty. A very light, soapy solution on a
sponge may be used to remove dirt and residue that
may accumulate in the texture. Be careful as not to let
any liquid get inside the chassis or contact the operat-
ing surfaces.
CHANNEL INSERT JACKS - These jacks are wired
post-EQ and post channel volume control. By inserting
an external signal source into one of these jacks,
through a stereo jack wired to the tip and sleeve (with
the ring left floating), the appropriate channel’s EQ
and volume control are bypassed. By shorting the tip
of the inserting jack to its ring, the channel’s signal
and the externally input signal could be mixed togeth-
er. The channel inserts can also serve as effects loop
points by using a stereo jack wired tip=effects send,
and ring=effects return. Note that the layout of the
insert jacks on the back panel is the mirror image of
the channels layout on the front panel.
Download from Www.Somanuals.com. All Manuals Search And Download.
KXR 2 0 0 BLO CK DIAGRAM
Channel 1
Balanced
Equalizer
Channel 1
Volume
High
Z
Input
Low Mid Hi
Reverb
Send
Insert
(Rear Panel)
Effects
Send
Effects
Return
Effects
Send
Channel 2
Balanced
Equalizer
Channel 2
Volume
High
Z
Effects
Loop
Input
(Rear Panel)
Low Mid Hi
Reverb
Send
Insert
(Rear Panel)
Effects
Send
Channel 3
Balanced
Equalizer
Channel 3
Volume
High
Z
Input
Reverb Circuit
Reverb
Return
DeltacompTM
Low Mid Hi
Reverb
Send
Insert
(Rear Panel)
Master
Volume
Speakers
Effects
Send
Power
Amp
Balanced
Low
Equalizer
Channel 4
Volume
Z
Line
Outputs
Low Low Hi Hi
Mid Mid
Channel 4
Inputs
Reverb
Send
Insert
(Rear Panel)
Effects
Send
Balanced
High
Z
TRO UBLESHO O TER‘S CHECKLIST
If the amplifier is set up but does not function, check the following items:
•
•
•
•
•
Is the amplifier power cord plugged into an electrical outlet ?
Is there power at the outlet ?
Are all the control knobs properly set ?
Are the controls knobs on the instrument properly set ?
Is the instrument properly plugged into the KXR 200 ?
(Eliminate any effect pedals and try another guitar cord.)
If after checking all of the above, and the system is still not performing correctly,
®
consult your Authorized FENDER Service Dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
KXR 2 0 0 SPECIFICATIO N S
PART NUMBER :
100V Version : 22-8572
120V Version : 22-8502
230V Version : 22-8562
240V Version : 22-8532
THIS EQUIPMENT CONFORMS TO
THE FOLLOWING DIRECTIVES :
EMC 89/ 336/ EEC AND LV 73/ 23/ EEC
TYPE SPECIFICATION :
PR 286
POWER REQUIREMENTS :
100V Version : 100VAC, 50/ 60Hz, 540W
120V Version : 120VAC, 60Hz, 540W
230V Version : 230VAC, 50Hz, 540W
240V Version : 240VAC, 50Hz, 540W
POWER AMPLIFIER SECTION :
POWER OUTPUT :
200W R.M.S.
RATED LOAD IMPEDANCE :
DISTORTION AT 200 WATTS :
4 Ω
Less than 1% @ 1kHz, below compression
Less than 1% @ 1kHz, maximum compression
SENSITIVITY :
1.03 Volts R.M.S.
22 kΩ
INPUT IMPEDANCE :
DELTACOMPTM RANGE :
PREAMP SECTION :
INPUT IMPEDANCE :
20dB.
XLR - 1.82 kΩ
Phone - 18.2 kΩ
Sensitivity for 200 watts :
channel and master
volume at maximum, all
tone control at “0”
XLR - 2.9 mV R.M.S.
Phone - 29 mV R.M.S.
EQUALIZER :
For 3-band-EQ sections :
+/ - 12dB at 130, 540 and 4200 Hz.
For 4-band-EQ section :
+/ - 12 dB at 125, 320, 1000 and 3200 Hz.
Sensitivity for channel
inserts, Master volume
at maximum setting
500 mV R.M.S. (-6dBV).
Sensitivity for
Master volume and FX
return control at max.
130 mV R.M.S. (-18dBV).
PHYSICAL SPECIFICATIONS :
HEIGHT :
29 - 3/ 4 inches w/ o casters
32 - 1/ 8 inches with casters
21 - 11/ 16 inches
12 inches
(75.6 cm)
(81.6 cm)
(55.1 cm)
(30.5 cm)
(40kg)
WIDTH :
DEPTH :
WEIGHT :
88 lbs.
SPEAKER COMPLEMENT :
15” Fender® Special Design (P/ N 048769)
Dual piezo horn (P/ N 028813)
WARNING : NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
A PRODUCT OF:
FENDER MUSICAL INSTRUMENTS CORP.,
CORONA, CA 9 1 7 2 0
Download from Www.Somanuals.com. All Manuals Search And Download.
|