Speed Dome
EPTZ900/500
USER MANUAL
Date: June 2006
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.1. Installation Requirements..............................................................2-20
2.4.2. EPTZ900 Dome Camera Wall Mount Installation .........................2-20
2.4.3. EPTZ500 Dome Camera Installation .............................................2-24
Separately Sold Accessories................................................................2-27
2.5.1. Pole mount......................................................................................2-27
2.5.2. Pole adapter....................................................................................2-27
2.5.3. Corner mount .................................................................................2-27
2.5.4. Multi-Function Keyboard Controller ...........................................2-27
2.5.
3.
4.
EPTZ900/500 CAMERA SETUP MENU.........................3-28
3.1.
Structure of the Setup Menu ................................................................3-28
3.1.1. Camera Setup Menu.......................................................................3-29
EPTZ900/500 FUNCTION SETUP AND OPERATION...4-33
4.1.
4.2.
4.3.
4.4.
4.5.
4.6.
Manual Control Mode............................................................................4-33
Auto Pan Mode ......................................................................................4-33
Position Setting.....................................................................................4-33
Tour Mode ..............................................................................................4-34
Alarm Link to a Position/Tour...............................................................4-35
Other operations ...................................................................................4-35
APPENDIX B: Protocol ............................................................4-37
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
1. EPTZ900/500 OVERVIEW
1.1. Introduction
EPTZ900/500, an intelligent high-speed dome camera is ready to secure your
property with its omni-directional and exact monitoring. An 18X optical and 12X digital
zoom combining with a high-performance chip makes captured images clear and
vivid. The other powerful camera functions this type of speed dome equips with:
¾
¾
¾
¾
PAL / NTSC image format suppose.
Auto and fast focus increases the searching speed and precision.
Auto Iris adjusts the monitoring image to the best brightness.
White Balance function makes the shades of color more natural in different
light conditions.
¾
¾
BLC (Backlight Compensation) function makes objects clear in a high
illumination background.
Color / B&W images auto switching to enhance the sensitivity in a low light
condition or at night.
Furthermore, the micro control unit enables camera a nimble and exact movement
from minimal 0.01°/sec to maximal 360°/sec. It can go to every preset position in 1
second. It also has other advantages such as:
¾
¾
¾
192 preset positions are available.
16 cruise tours can be set, and each tour contains up to 16 positions.
Up to256 speed domes can be supported on a RS485 bus when all speed
domes are controlled by multi-function keyboard controller.
Auto heater and fan to fit all kinds of temperature.
¾
¾
Provide 4 alarm inputs and 1 alarm output.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
All of the features make the intelligent high-speed dome camera works for a wide
range and demanding application such as banks, airports, stations, casinos, streets
of cities, intelligent buildings, and etc.
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2. Specifications
Model
EPTZ900
1/4" type Sony Super HAD CCD
EPTZ500
Pickup Device
Video Format
Scanning System
NTSC or PAL
NTSC: 525 TV lines, 60 fields/sec
PAL: 625 TV lines, 50 fields/sec
Picture Elements
Horizontal Resolution
Sensitivity
768 x 494 ( NTSC ) , 752 x 582 ( PAL )
480 TVL
1.0 Lux/F=1.4
S/N Ratio (AGC OFF)
Electronic Shutter
Digital Slow Shutter
Shutter Selection
Lens Type
Over 50dB
1/50~1/10,000 (s)
No
No
18x optical zoom , f=4.1 mm (wide) to 73.8mm (tele) , F1.4 to F3.0
Zoom Ratio
216x max (18x Optical and 12x Digital Zoom )
Auto ICR
No
ON/OFF
Black Light Comp.
Auto Gain Control
White Balance
Auto
Auto/Indoor/Outdoor
BNC 1.0Vp-p , 75ohm
Line Lock/Internal Sync
24VAC
Video Output
Sync. Mode
Power Source
Power Consumption
Operating Temperature
Operating Moisture
Communication
18W; 70W with heater
18W
-40°C~50°C ; -40°F~122°F
0°C~50°C ; 32°F~122°F
≤95%
RS-485
Communication Speed
Horizontal Rotation Speed
Horizontal Rotation Range
Tilt Rotation Range
Auto Flip
1200/2400/4800/9600bps
0.1°/s－360°/s (1-239 grade shift gears)
360° unlimited rotation
90° pendulum motion
Rotates 180° when camera tilts to the vertical position
Control speed auto-adjusted according to zoom length changing
Auto Zoom Speed Control
Auto Pan, 2 Points Scanning
Auto Pan Speed
Can set freely
1－239 grade available
1－239 second available
192 positions
Dwell Time (2 points)
Preset Positions
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
1－239 grade available,0.1º/s - 360º/s
1－239 second available
16 group
Running To Position Speed
Dwell Time At Preset Position
Tour
Tour Point Per Group
Fan, Heater (EPTZ900)
Position Accuracy
Alarm
16 preset positions
Fan & Heater auto starts
No
±0.1°
4 in 1 out with tour/position auto triggering
Proportional Pan Speed
Built-in menu for functions
Built-in Protocols
Yes
Yes
Auto, EVF, Plus-D, A-Type, Pelco-D, Pelco-P
RS485
Communication
Address editable through DIP
switch
Yes
Speed Dome Address
Manual Pan/tilt speed
Weatherproof Ratings
Dimensions
0-255
Pan: 0.1º ~ 180º/s
Tilt: 0.1º ~ 180º/s
IP66
Indoor
208.5mm (W) x 221.6mm (H)
/
218.5mm (W) x 267.5mm (H) /
8.6" (W) x 10.5" (H)
4.2kg/9.25lbs
8.2" (W) x 8.7" (H)
2.15kg/4.8lbs
Weight
Certifications
CE ; FCC
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3. Feature
1.3.1. Profile of EPTZ900/500
EPTZ900
Wall Mount Bracket
M5 Bolt (Hex) x3
Base PCB board
Control board
Housing
Connection Bus
Power Cable
BNC Cable
Inner Housing
M3 Bolt x3
RS485 Cable
Mechanical Part
Camera Module
Bulb
EPTZ500
Power Cable
BNC Cable
Base PCB board
Control board
Clip
RS485 Cable
Housing
Connection Bus
Mechanical Part
Ceiling
Button
Bulb
Camera Module
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3.2. Base Board
The base board that is on the bottom of the housing connects to power cable, video
cable, control cable, alarm cable, fan and heater (fan and heater are for EPTZ900 only). In
order to connect to cables, the board needs to be taken off, and put back after finishing
connecting to all cables. The connectors of cable names are marked on the board in white
text. The details of the alarm connector (JP5) are shown on the APPENDIX A.
For EPTZ900, JP1, JP3 and JP6 that are two-pin connectors on the base board need to
be taken off during installation. JP1 and JP3 are connectors for heater, and they can be
switched. JP6 is a fan controller connector that turns on/off of the fan. The 3 cables are too
short to be connected to a wrong connector when putting them back.
RELAY
JP5
Video +
Video -
RS485 +
RS485 -
AC24
AC24
JP4
JP6
JP3
JP1
EPTZ900 Baseboard
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
JP5
RELAY
EPTZ500 Baseboard
1.3.3. EPTZ900/500 Control Board
The PCB board with two dipswitches is the control board of speed dome. The two
switches are used to set address, protocol, Baud Rate, video format and terminator
resistance.
CPU
SW2
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
SW1
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4. EPTZ900/500 Connection
110V AC
24V AC
POWER
24V AC / 3.5 A
Adapter
BNC
1.0Vpp ± 0.2V, 75
Video Out
Ω
RS485 Tx(+)
RS485 Tx(-)
RS485 Control Line
Alarm 1
EPTZ900/500
Alarm 2
Alarm 3
Alarm 4
4 ALARM INPUTS
GROUND
ALARM OUTPUTS
N.C.
N.O.
COM
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5. EPTZ900/500 Quick Operation Guide (Work with EKB500)
EPTZ900/500 and EKB500 (Keyboard) can work together by using factory
default setting. You just need to connect cables by following the steps:
1. Connect the RS485 cable to EPTZ900/500 and a Keyboard (EKB500).
2. Connect a video cable from EPTZ900/500 to a monitor.
3. Connect the power to the EPTZ900/500 and a Keyboard (EKB500) .
After the speed dome finishes the self-test mode, you can start to operate the
speed dome via the keyboard.
To operate the EPTZ900/500:
UP
IRIS
+
Focus
F.
Zoom
In
Zoom OUT
Zoom IN
LEFT
RIGHT
-
N.
Out
DOWN
1. Shift the Joystick up/down or right/left to view from camera.
2. Turn the top of the Joystick to zoom in/out.
3. Press Zoom In/Out, Focus F. /N. and IRIS +/- function keys to operate the
EPTZ900/500.
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. EPTZ900/500 INSTALLATION
2.1. Packing List
There are 3 boxes that are housing, bulb and mechanical part with a camera module,
one wall mount bracket, one power adapter and one accessory packet in the package.
The detail accessories list below:
¾
¾
¾
¾
¾
¾
Housing x1
Bulb x1
Mechanical part with a camera module x1
Wall mount bracket x1
Adapter x1
Accessory packet
— Glove x2
— M5 Hex Allen wrench x1
— Pin connector x1
— M5 screw (Hex) x3 for wall mount bracket fixing
— M3 screw x3 for bulb fixing
— Anchor nut and wall mount screw x4
2.2. Cable Needed
z
Power Cable
An adapter with 24V AC/3.5A output provides the power to the speed dome. An
extension power line may be needed.
Note: The input AC voltage range of an adapter depends on different area.
Please make sure the voltage range before installing.
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
z
Video Cable
A BNC cable is used for connecting a speed dome to a DVR or a monitor. An amplifier
may be needed if the video cable is too long.
z
Control Cable
Basically, EPTZ900/500 uses a differential pair to connect to other devices by
cascading. A cable that has low signal decline can be used as a control cable.
z
Alarm Cable
An alarm cable is not included in the packing list. A suitable wire can be used as an
alarm cable.
2.3. Initial Setup
Initial setup includes dome address, communication protocol, transmission speed,
video format, and terminator resistance settings. All of the settings should be confirmed
before the dome is installed. The control-related setting that is address, communication
protocol and transmission speed have to be set consistently with the control device such
as a keyboard or a DVR.
Notice: Please make sure the power is off before setting, and restart the speed dome to
enable a new value after changing.
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.1. Address Setting
The address code of the EPTZ900/500 should be set to correspond properly with a
control device to control multiple dome cameras. The address codes are made up by
the dipswitch SW1 (8 bits) on the PCB board. The 8 bits dipswitch indicates the binary
coded of the address, and there are 256 addresses can be selected (0 ~ 255, 28 = 256).
It also means that there up to 256 dome cameras can cascade on the RS485 bus. The
dipswitch setting and the indicated address are represented in the following chart.
Note: The factory default address is 1.
Notice: Please make sure the power is off before setting, and restart the speed dome
to enable a new value after changing.
CPU
SW2
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
SW1
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch
Address
Switch
Address
Sw
i
tch
Address
Sw
i
t
ch
Addre
ss
ON
ON
ON
ON
0
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
ON
ON
ON
ON
1
1
1
1
1
ON
ON
ON
ON
2
1
1
1
1
ON
ON
ON
ON
3
1
1
1
1
ON
ON
ON
ON
4
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
1
1
1
1
ON
ON
ON
ON
5
1
1
1
1
ON
ON
ON
ON
6
1
1
1
1
ON
ON
ON
ON
7
1
1
1
1
ON
ON
ON
ON
8
1
1
1
1
ON
ON
ON
ON
9
1
1
1
1
ON
ON
ON
ON
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch
Address
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Switch
Address
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Switch
Address
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Switch
Address
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
ON
ON
ON
ON
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.2. Communication Protocol Setting
The 1st, 2nd and 3rd bits of the SW2 are used to set communication protocol. The
factory default protocol is EVF.
EVF - 1
PELCO-D
PELCO-P
TYPE-A
SW2
Protocol
Baud Rate
PAL / NTSC
Maching Resistance
Notice: Please make sure the power is off before setting, and restart the speed dome to
enable a new value after changing.
Set all of protocol switches to ON; the EPTZ900/500 will enter a self-test mode.
2.3.3. Transmission Speed Setting (Baud Rate Setting)
The 4th and 5th bits of the SW2 on the PCB board are used to set the Baud Rate. The
default baud rate setting is 9600.
9600 BPS
4800 BPS
2400 BPS 1200 BPS
SW2
Protocol
Baud Rate
PAL / NTSC
Maching Resistance
Notice: Please make sure the power is off before setting, and restart the speed dome to
enable a new value after changing.
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.4. Video Format Setting
The 6th bits of the SW2 on the PCB board are used to set the video format. The
default video format depends on the factory setting. Please do not change it.
NTSC
PAL
SW2
Protocol
Baud Rate
PAL / NTSC
Maching Resistance
Notice: Please make sure the power is off before setting, and restart the speed dome to
enable a new value after changing.
2.3.5. RS-485 Bus Terminator Resistance
For central controlling, the terminator resistance should be set for the device that is
the furthest one away from the controller. The 8th bit on the SW2 is a switch to enable or
disable the terminator resistance. When it is switched ON, the BUS terminator
resistance is connected.
OFF
ON
SW2
Protocol
Baud Rate
PAL / NTSC
Maching Resistance
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
n ≦ 255
RS485
Keyboard
DVR
Ternimator
Resistance
ON
Control Unit
CAM-0
CAM-1
CAM-n
Note: When the dome is out of control, or does not work under control well, try to switch
the terminator resistance ON.
Notice: Please make sure the power is off before setting, and restart the speed dome to
enable a new value after changing.
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4. Rack and Speed Dome Installation
2.4.1. Installation Requirements
1. Installation should be handled by a qualified service agent and should comply with
all local regulations. Service personnel should expect potential problems such as
surface strength, surface material, falling objects, outer breaches, building vibration
or other similar conditions.
2. Check for all necessary materials, and ensure if the selected installation location is
suitable for the speed dome.
2.4.2. EPTZ900 Dome Camera Wall Mount Installation
Notice: Installation location that is a wall, a pole or a ceiling needs to support above five
times the total weight of the camera assembly (about 16 kg) to avoid shaken images, and
dropping.
1. Set wall mount bracket on the wall. Mark the center of the holes on the wall against
the bracket holes. Use a drill to make 4 holes that can be nailed 4 0.25” X 1.25”
screws at the marks.
Notice: The length of the screws depends on the surface material. The mentioned screws
are used in the normal concrete surface.
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Thread the cable through the hole in the wall mount bracket, and screw in 4 M8
nuts for mounting the bracket.
3. Take off the housing from the packing, and take off the baseboard (4 bolts on it.)
inside the housing. Thread the cable through the top of the housing. Fix the
housing on the wall mount bracket, and screw in 3 M5 bolts (Hex) on the top of the
bracket with the attached Hex Allen wrench to fix the housing.
M5 Bolt
Hex Allen wrench
RELAY
JP5
Video +
Video -
RS485 +
RS485 -
AC24
AC24
JP4
JP6
JP3
JP1
4. Connect the cable connectors to the nodes on the baseboard, and then fix the
baseboard in the housing by screwing 4 bolts on it.
Notice: Please notice the polarity of control line. The EPTZ900 will not work if the polarity
of control line is mis-connected.
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Align the two screw holes on the bottom of mechanical part to the two bolts on the
base of the housing, and twist the mechanical part clockwise a little bit in order to
engage it with the base. Screw the two bolts on the base, and then connect and fix
the connection bus to the PCB board on the mechanical part.
Notice: The camera module on the mechanical part is very sensitive. Please be careful
when installing this part.
6. Remove the lens protection cover before installing the bulb. Align the 3 bolt holes
into the 3 housing bolt holes, and screw thee M3 bolts with the attached small
screw driver to fix the bulb.
M3 Blot
M3 Blot
GLOVE
2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice: In order to protect the bulb from dirt and scrape, please put on the gloves before
installing the bulb.
7. Turn on the power, and start to operate the EPTZ900.
Note: When turning on the power, the EPTZ900 will enter self-inspection mode, and carry
out a self-testing program. After finishing self-inspection, you can start to operate
the EPTZ900.
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.3. EPTZ500 Dome Camera Installation
1. Take off the housing from the packing, and take off he PCB board (4 bolts on it) inside
the housing.
2. Cut the ceiling against the housing’s shape with a saw.
3. Thread the cable through the screw and the hole on the top of the housing, and tighten
up the screw to fix the cable
4. Place the housing into the hole that you just made. Fix the housing on the ceiling with
two clips, adjust the screws of clips to make the housing perfectly fit to the ceiling.
5. Connect the cable connectors to the nodes on the base board, and then fix the base
board in the housing by screwing 4 bolts on it.
Cut the ceiling
RELAY
JP5
2-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice: Please notice the polarity of control line. The EPTZ500 will not work if the
polarity of control line is mis-connected.
6. Align the two screw holes on the bottom of mechanical part to the two bolts on the
base of the housing, and twist the mechanical part clockwise a little bit in order to
engage it with the base. Screw the two bolts on the base, and then connect and fix the
connection bus to the PCB board on the mechanical part.
Notice: The camera module on the mechanical part is very sensitive. Please be careful
when installing this part.
7. Remove the lens protection cover before installing the bulb. Screw the connection
wire to the housing in order to prevent the bulb from being drop down. Align the 2
buttons on the bulb base with the 2 buttons on the housing, and push bulb base to clip
the housing.
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection wire
Button
Button
GLOVE
Notice: In order to protect the bulb from dirt and scrape, please put on the gloves before
installing the bulb.
8. Turn on the power, and start to operate the EPTZ500.
2-26
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5. Separately Sold Accessories
2.5.1. Pole mount
The pole mount is used for installing a speed dome on the ceiling
indoors or outdoors.
The extension poles are available for the pole mount.
2.5.2. Pole adapter
The pole adapter is used for installing a wall mount bracket to a
pole indoors or outdoors.
2.5.3. Corner mount
The corner mounts are used for installing a wall mount bracket to a
270° corner of walls indoors or outdoors.
2.5.4. Multi-Function Keyboard Controller
Multi-Function System Controller
Capable of controlling PTZ, DVR and Monitor
3D Joystick control of PTZ function
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
3. EPTZ900/500 CAMERA SETUP MENU
In this section, setup and operation guide of EPTZ900/500 will be introduced.
There are 22 items of the setting menu. However, there is only one line on the line
display, so using some combination keys to operate is necessary.
3.1. Structure of the Setup Menu
Press MENU to enter camera setup menu.
Press Shift + Joystick up/down to change subentries, and right/left to change the setting.
Items
Option
CAM ID
-----------------
DZOOM
OFF / ON
FOCUS
AUTO / MAN / ONE PUSH
OFF / ON
NEGATIVE
COLOR
OFF / ON
DISPLAY
OFF / ON
BACKLIGHT
WBC MODE
TITLE DISPLAY
AUTO FLIP
ALM-IN1 SET
ALM-IN2 SET
ALM-IN3 SET
ALM-IN4 SET
ALM-IN PRIO
ALM-OUT
OFF / ON
AUTO / INDOOR / OUTDOOR / MAN
OFF / ON
OFF / ON
N.O. / N.C. / OFF
N.O. / N.C. / OFF
N.O. / N.C. / OFF
N.O. / N.C. / OFF
1234 / 2341 / 3421 / 4123
OFF / ON
LOAD DEFAULT
EXIT MENU
-----------------
-----------------
3-28
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.1. Camera Setup Menu
Press MENU to enter camera setup menu.
Press Shift + Joystick up/down to change subentries, and right/left to change the setting.
1. CAM ID： The name assigned to the camera.
2. DZOOM： Digital zoom enable or disable.
ON: Enable a digital zoom.
OFF: Disable a digital zoom.
3. FOCUS： Focus type, auto focus and manual focus are available.
AUTO: Auto focus is enabled.
MAN: Manual focus is enabled.
ONE PUSH: Enable the one push trigger focus mode. The focus lens holds the same
position until the next trigger command is received. This function prevents
the wrong focus in dark.
4. NEGATIVE： Negative image.
ON: Enable a negative image.
OFF: Disable a negative image.
5. COLOR： Color display.
ON: Enable a color display.
OFF: Disable a color display, and show a B&W display.
3-29
Download from Www.Somanuals.com. All Manuals Search And Download.
6. DISPLAY： Display system information and status.
ON: To display the system information and status on the screen.
OFF: Not to display the system information and status on the screen.
7. BACKLIGHT： Backlight compensation.
ON: Enable backlight compensation.
OFF: Disable backlight compensation.
8. WBC MODE： White balance mode.
AUTO: Auto white balance mode.
INDOOR: Indoor white balance mode.
OUTDOOR: Outdoor white balance mode.
MAN: Manual white balance mode.
9. TITLE DISPLAY : Display the title.
ON: Enable title display.
OFF: Disable title display.
10. AUTO FLIP： Flip the camera when it tilts to the 90° end.
ON: Enable auto flip.
OFF: Disable auto flip.
11. ALM-IN1 SET： The status of input alarm 1.
N.O.: Enable a normal open alarm input.
N.C.: Enable a normal close alarm input.
OFF: Disable alarm input.
3-30
Download from Www.Somanuals.com. All Manuals Search And Download.
12. ALM-IN2 SET： The status of input alarm 2.
N.O.: Enable a normal open alarm input.
N.C.: Enable a normal close alarm input.
OFF: Disable alarm input.
13. ALM-IN3 SET： The status of input alarm 3.
N.O.: Enable a normal open alarm input.
N.C.: Enable a normal close alarm input.
OFF: Disable alarm input.
14. ALM-IN4 SET： The status of input alarm 4.
N.O.: Enable a normal open alarm input.
N.C.: Enable a normal close alarm input.
OFF: Disable alarm input.
15. ALM-IN PRIO： The priority of alarms.
1234: The alarm priority is 1>2>3>4.
2341: The alarm priority is 2>3>4>1.
3412: The alarm priority is 3>4>1>2.
4123: The alarm priority is 4>1>2>3.
16. ALM-OUT： Alarm output. There is a built-in relay to offer an alarm output.
ON: Enable alarm output.
OFF: Disable alarm output.
3-31
Download from Www.Somanuals.com. All Manuals Search And Download.
17. LOAD DEFAULT： Load default setting.
Select this item, and then press “Enter” to load default setting.
Press “Clr” + “Menu” whenever you want to quit menu setting.
18. EXIT : To exit.
Select this item, and then press “Enter” to quit setting.
Press “Clr” + “Menu” whenever you want to quit menu setting.
3-32
Download from Www.Somanuals.com. All Manuals Search And Download.
4. EPTZ900/500 FUNCTION SETUP AND OPERATION
4.1. Manual Control Mode
¾
Manual control: Shift Joystick Up/Down/Left/Right, and turn it
Clockwise/Counterclockwise to control speed dome.
Use the control keys which are Zoom, Focus and IRIS function keys on the
keyboard to zoom In/Out, focus N (near)/F (Far), or IRIS +/-.
HOME Mode: The camera view will go back to the home position when there is no
keyboard operation in a specific time. The home position and the specific time can
be set by press Set + Home.
¾
4.2. Auto Pan Mode
¾ Two point auto pan: Press A.Pan to enter the auto pan mode, and then the
system will ask you to enter the auto pan speed (1~239). Press Enter to start auto
pan.
In order to set the two points, press Set + A.Pan, and then enter the dwell time
(1~239 seconds) of each point.
¾
360° auto pan: Press Shift + A.Pan to enter the 360° auto pan. The camera will
turn 360° automatically, but not tilt.
4.3. Position Setting
Focus on a preset position: Press the number key, and then press Position to
¾
focus on the number of preset position; or you can press Position, then enter the
preset position number, and then press Enter to focus on the number of preset
position.
4-33
Download from Www.Somanuals.com. All Manuals Search And Download.
¾
¾
Preset a position: Shift the Joystick to the position you would like to preset, and
then press Shift + Position. The system will ask you to enter the preset position
number (1~239), and then press Enter to save the position. There are up to 192
positions can be preset.
Set the parameter of a preset position: Press Set + Position to set the parameter
of a preset position. You can set the going-to speed (1~239), dwell time (1~239
seconds), and the title of the position. Shift the joystick Right/Left to change bits,
and shift the Joystick Up/Down to change the alphanumeric characteristic. The
available alphanumeric characteristics are 0~9, A~Z, &, ?, !, :, ‘, ., ,, /, -, and a
space.
¾
Delete a preset position: Press Clr + Position to delete a preset position. The
system will ask you to enter the position number that you would like to delete, and
then press Enter.
4.4. Tour Mode
In the tour mode, you can set a tour for viewing. There are 16 tours can be set, and 16
preset positions in a tour.
¾
One-way tour Mode: Press Tour to enter the tour mode. The system will ask you
to enter the tour number you would like to run, and starts the tour after pressing
Enter. To preset a tour before running it is necessary.
Preset a one-way tour: Press Set + Tour to preset a one-way tour. The system will
ask you to enter preset position numbers (The positions need to be preset). After
finish entering all positions, press Stop to quit, and then press Enter to save the
tour.
¾
To-and-fro tour mode: Press Shift + Tour to run a to-and-fro tour. The system will
4-34
Download from Www.Somanuals.com. All Manuals Search And Download.
ask you to enter the tour number you would like to run, and starts the tour after
pressing Enter. To preset a tour before running it is necessary.
Note: The difference between the One-way tour mode and To-and-fro tour mode is their
return modes. For example: There is a tour with 3 preset positions 1, 2 and 3. The camera
runs 1→2→3→1→2→3 in the One-way tour mode, and 1→2→3→2→1 in the To-and-fro
tour mode.
4.5. Alarm Link to a Position/Tour
The EPTZ900/500 has 4 alarm inputs that can be set to link to a position or a tour when
an alarm is triggered.
¾
Set an alarm link:
Press F1 to set an alarm link. Enter the alarm number, and then press Enter.
Switch the Joystick up/down to select a position or a tour, enter a position or tour
number, and then press Enter to confirm the alarm link setting.
Delete an alarm link:
¾
Press Clr + F1 to delete a link of alarm to position/tour.
4.6. Other operations
The EPTZ900/500 can work with a DVR that has PTZ control functions, and a
matching protocol. The available control functions depend on different DVRs.
The EPTZ900/500 can work with a keyboard that has PTZ control functions, and a
matching protocol. The available control functions depend on different keyboards.
4-35
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A: The Alarm I/O Connection
There are 4 alarm inputs and 1 alarm output available. The alarm I/O connector that is
marked as JP5 is a nine-pin connector. It is located on the PCB board of the housing.
JP5
1 ~ 9
JP5
RELAY
RELAY
JP5
Video +
Video -
RS485 +
RS485 -
AC24
JP5
AC24
JP4
JP6
JP3
JP1
1 ~ 9
EPTZ900 base board
EPTZ500 base board
Pin #
Function
1
2
3
4
5
6
7
8
9
Alarm Input 4
Ground
Alarm Input 3
Alarm Input 2
Ground
Alarm Input 1
Normal Open (N.O.)
Common (COM)
Normal Close (N.C.)
4-36
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B: Protocol
=================================================
Speed Dome Control Protocol
=================================================
1-1. Format
A. Fixed 7 bytes packet
Byte1 (cmd1 = 0xFA)
Byte2 (cmd2)
Byte3 (ID high byte)
Byte4 (ID low byte)
Byte5 (data1)
Byte6 (Keyboard-ID)
Byte7 (checksum)
B. Fixed 8 bytes pcket
Byte1 (cmd1 = 0xFC)
Byte2 (cmd2)
Byte3 (ID high byte)
Byte4 (ID low byte)
Byte5 (data1)
Byte6 (Keyboard-ID)
Byte7 (data2)
Byte8 (checksum)
1-2. checksum calculation
1. Address = IDH*32 + IDL
2. Movement Speed: 01-EF ==> begin speed value (01:Slow, EF:Fast)
00
==> stop
3. checksum ==> B7=(B1+B2+B3+B4+B5+B6)&0x7f
4-37
Download from Www.Somanuals.com. All Manuals Search And Download.
2-1. Part-I
==============================================================================================================
| (B1) (B2)
| CMD1 CMD2
(B3) (B4) (B5)
IDH IDL DATA1
(B6) (B7) |
FUNCTION
KB-ID CSUM | DESCRIPTION
------------------------------+------ ------ ----- ----- ------- ----- -----+---------------------------------
Up
| FA
| FA
| FA
| FA
| FA
| FA
| FA
01
02
03
04
05
06
00-1F 00-1F speed
00-5F cs | speed=00-EFh
Down
.
.
.
.
.
.
.
speed
speed
speed
speed
speed
grade
.
.
.
.
.
.
cs |
cs |
cs |
cs |
cs |
cs |
Left
Right
.
Left-up
Left-down
Broadcase
.
.
09-0E 20
00
==============================+====== ====== ===== ===== ======= ===== =====+=================================
Location A
Location B
| FA
| FA
0F
13
.
.
.
.
WaitT
WaitT
.
.
cs | WaitT=0-EFh (second)
cs |
------------------------------+ ----- ------ ----- ----- ------- ----- -----+---------------------------------
Line Scaning Startup
Right-up
| FA
| FA
| FA
| FA
10
07
08
.
.
.
.
.
speed
speed
speed
speed
.
.
.
.
cs | speed =01-EFh
cs |
cs |
cs |
Right-down
.
Broadcase
01-08 20
00
==============================+====== ====== ===== ===== ======= ===== =====+=================================
Iris Open
| FA
| FA
| FA
| FA
| FA
| FA
| FA
09
0A
0B
0C
0D
0E
11
.
.
.
.
.
.
.
.
.
.
.
.
.
.
grade
grade
grade
grade
grade
grade
speed
.
.
.
.
.
.
.
cs | grade=00-EFh
Iris Close
Zoom Tele
cs |
cs |
cs |
cs |
cs |
cs |
Zoom Wide
Focus Far
Focus Near
Surface scan Startup
------------------------------+ ----- ------ ----- ----- ------- ----- -----+---------------------------------
startup cruise group
startup intercruseScan
| FA
| FA
71
72
.
.
.
.
group
group
.
.
cs | group=1-16
cs |
------------------------------+ ----- ------ ----- ----- ------- ----- -----+---------------------------------
Set Preset pos
To Preset pos
| FA
| FA
75
76
.
.
.
.
pp
pp
.
.
cs | pp=1-192 (position)
cs |
------------------------------+ ----- ------ ----- ----- ------- ----- -----+---------------------------------
cruise set start
adding cruise point
cruise set close
| FA
| FA
| FA
77
78
79
.
.
.
.
.
.
group
pp
.
.
.
cs | group=1-16
cs | pp=1-192 (position)
cs |
AA
4-38
Download from Www.Somanuals.com. All Manuals Search And Download.
------------------------------+ ----- ------ ----- ----- ------- ----- -----+---------------------------------
Set Single Point Alarm Linkage| FA
Clr Single Point Alarm Linkage| FA
7A-7D
7E-81
82-85
86-89
.
.
.
.
.
.
.
.
pp
.
.
.
.
cs | pp=1-192 (position)
AA
cs |
Cruise Alarm Linkage Set
| FA
| FA
group
AA
cs | group=1-16
cs |
Cruise Alarm Linkage Cancel
------------------------------+ ----- ------ ----- ----- ------- ----- -----+---------------------------------
set preset position parameter | FA
speed to preset position | FA
A0
A1
A2
A3
.
.
.
.
.
.
.
.
pp
.
.
.
.
cs | pp=1-192 (position)
cs | speed=1-EFh
cs | dwell=1-EFh (seconds)
cs |
speed
dwell
AA
Dwell time at preset position | FA
Set PresetPosition Param Close| FA
------------------------------+ ----- ------ ----- ----- ------- ----- -----+---------------------------------
Home Position Set
| FA
| FA
A4
A5
A6
.
.
.
.
.
.
AA
.
.
.
cs |
Wait time at Home Position
WaitT
on-off
cs | WaitT=0-EFh (minutes)
cs | on-off=0/1 (0=off, 1=on)
Enable Home position On/Close | FA
------------------------------+ ----- ------ ----- ----- ------- ----- -----+---------------------------------
Clear Preset Position | FA A7 pp cs | pp=1-192 (position)
==============================+====== ====== ===== ===== ======= ===== =====+=================================
.
.
.
Speed Dome Setup Menu
| FA
90
.
.
operate
.
cs | operate=01 Enter menu mode
|
|
|
|
|
|
|
|
|
|
|
|
|
|
=02 Exit menu mode
=03 menu cursor up
=04 menu cursor down
=05 menu cursor left
=06 menu cursor right
=07 select option
=08 confirm
==============================================================================================================
2-2. Part-II ( Enhance part )
================================================================================================================
| (B1) (B2)
| CMD1 CMD2
(B3) (B4)
IDH IDL
(B5)
(B6)
(B7)
(B8) |
FUNCTION
DATA1 KB-ID DATA2 CSUM | DESCRIPTION
------------------------------+------ ----- ----- ----- ------ ----- ----- -----+---------------------------
enhance move
| FC
OP
.
.
x-spd
.
y-spd
cs | OP: (0-3)
|
|
|
|
|
|
|
|
bit0: (0=right, 1=left)
bit1: (0=up, 1=down)
| x-spd=0-EFh
| y-spd=0-EFh
4-39
Download from Www.Somanuals.com. All Manuals Search And Download.
------------------------------+------ ----- ----- ----- ------ ----- ----- -----+---------------------------
set preset position title
| FC
05
.
.
x-coor
.
char
cs | x-coor=0-19
| char=ASCII code
| notice:
|
|
|
| make sure you already send
| "FA A0" command, befoe send
| this command.
|
|
|
|
clean preset position title
| FC
0A
.
.
PP
.
00
cs | PP=1-192
------------------------------+------ ----- ----- ----- ------ ----- ----- -----+---------------------------
Remote reboot
| FC
|
0C
.
.
55
.
AA
08 |
|
================================================================================================================
4-40
Download from Www.Somanuals.com. All Manuals Search And Download.
EverFocus Electronics Corp.
China Office:
Head Office:
Room 609, Technology Trade Building,
Shandgdi Information Industry Base,
Haidian District, Beijing,China
TEL: +86-10-62971096
12F, No.79 Sec. 1 Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886-2-26982334
FAX: +886-2-26982380
FAX: +86-10-62971432
USA Office:
Japan Office:
1801 Highland Ave. Unit A
Duarte, CA 91010, U.S.A.
TEL: +1-626-844-8888
FAX: +1-626-844-8838
1809 WBG MARIBU East 18F,
2-6 Nakase.Mihama-ku.
Chiba city 261-7118, Japan
TEL : +81-43-212-8188
FAX : +81-43-297-0081
European Office:
Albert-Einstein-Strasse 1
D-46446 Emmerich, Germany
TEL: 49-2822-9394-0
FAX: 49-2822939495
P/N : MW01G00900
4-41
Download from Www.Somanuals.com. All Manuals Search And Download.
|