EVERFOCUS
Dual Power High Resolution Vandal Proof
Weather Resistant 3-Axis IR Dome Camera
Operation Instructions
Model No. EHD363
Please read this manual first for correct installation and operation. This manual should be retained for
future reference. The information in this manual was current when published. The manufacturer reserves
the right to revise and improve its products. All specifications are therefore subject to change without
notice.
PRECAUTIONS
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers
since the electromagnetic fields generated from these devices may distort the video image or otherwise interfere
with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce materials
other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage.
3. Try to avoid facing the camera toward the sun.
In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal circuits, as
well as creating unbalanced illumination beyond the capability of the camera to compensate.
4. Keep the power cord away from water and other liquids and never touch the power cord with wet
hands.
Touching a wet power cord with your hands or touching the power cord with wet hands may result in electric
shock.
5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning
For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the hands. Use
lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens. Use a damp soft
cloth to remove any dirt from the camera body. Please do not use complex solvents, corrosive or abrasive
agents for cleaning of any part of the camera.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
ꢀ
Weather resistant, IP66 rated
Dual power: 12VDC/24VAC
PACKAGE CONTENTS
ꢀ
ꢀ
Camera Unit x 1
Mounting kit includes:
-Screws x 4
-Security wrench for housing screws x 1
-Expanding Anchors x 4
-Washers x 4
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Operation Instructions (this document) x 1
Weatherproof bushing x 1
Power cable x 1
Video cable x 1
Power adapter pigtail (for NTSC model only) x 1
Mounting template x 1
SPECIFICATIONS
Pickup Device
Video Format
Picture Elements
Horizontal Resolution
Sensitivity
SONY 1/3” 960H EXview HAD II CCD High Resolution
NTSC
976 x 494
700 TV line
0.01Lux / F1.4; 0Lux / IR
More than 54 dB
S/N Ratio
Electronic Shutter
Video Output
Gamma Correction
Lens Type
1/60s~1/100,000s
BNC-F 1.0Vp-p 75Ω
0.45
Vari-Focal 3.7~12mm / F1.4 DC Drive Auto Iris Lens
True day/night with motorized IR cut filter
Automatic
Day/Night
Gain Control
White Balance
Digital WDR
Noise Reduction
Sync. Mode
ATW (1800°K~10500°K) with Anti-CR Function
ATR On (Luminance and Contrast = High)
2-D DNR (C Level 4, Y Level 4)
Internal Sync.
IR LED
11 Units High Efficiency IR LED
850nm
IR Wavelength
IR Distance
30m (~98ft.) nominal; depends on environment
IP 66
Weather Resistant
Vandal Proof
Power Source
Power Consumption
IK10
12VDC or 24VAC
283mA @12VDC, 8W @ 24VAC
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Temperature
Dimensions (O.D. x H)
Weight
-10°C~50°C / 14°F~122°F
142mm x 115.5mm / 5.6” x 4.55”
979 g / 2.16 lbs
Certifications
CE / FCC
DIMENSIONS
C
B
A
Dimensions
Front View
D
F
E
G
Bottom View
Bottom View
A. Lens
E. Mounting holes
F. BNC Connector
G. DC Connector
B. IR-LED
C. Side conduit entry
D. Back conduit entry
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Drill the Holes
1. Locate the desired mounting location; position housing with camera pointed generally in the desired
direction and mark location.
2. Use template to fix hole locations. Drill 4 holes for mounting screws (or anchors and insert plastic
anchors into holes after drilling as required).
Mounting Steps
1. Use the security wrench provided to loosen the 4 screws holding the dome cover.
2. Remove the dome cover. (IF REAR WIRE MUST BE REMOVED/RELOCATED, SEE STEPS
4~8) Attach the camera body to the mounting surface with the mounting screws provided
3. Tighten the 4 mounting screws to secure the camera body to the mounting surface.
4. If you need to wire cable through side conduit hole, use a coin to remove the conduit plug; save the
plug as it will be used to close the rear conduit hole.
Back conduit
hole
Conduit plug
Side conduit hole
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Disconnect the power and video wire from the camera board end of the wire (1x 4 pin white connector)
and the 2 power wires from the power board attached to the base plate (1 x 2 pin connector with blue
marking and 1 x 2 pin connector with white color). Gently pull the wires out from under the plate until
they are free. Using wrench or pliers, remove the weather tight bushing from the rear conduit hole. Using
the plug removed in step 3 above, close the rear conduit hole (additional caulk or other sealant
recommended).
6. Pass the camera end of the power/video cable through side conduit hole. Using wrench or pliers,
carefully tighten the weather tight bushing into the side conduit hole.
7. (Optional) Pass the power/video wires under the base plate and up through the center hole.
8. Position the power/video wires so that they don’t interfere with the camera module and carefully
attach the 4 pin white connector to the camera board, being sure to position the connector so it fits
properly onto the tiny pins within. Next, attach the blue 2 pin connector and the white 2 pin connector to
the matching color receptacles on the power board. NOTE: the 2 pin blue connector goes into the
receptacle marked in blue on the power board. Failure to properly attach these connectors may
permanently damage the camera.
General Connection and Setup
1. Connect the power cord to DC 12V or AC 24V power supply
2. Use 75 ohm type coaxial cable to connect the camera to a monitor or DVR.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Loosen the screws which lock the tilt mechanism. Rotate the pan and tilt mechanisms to point
the camera in the desired direction. Rotate the camera module on its axis if necessary to align the
image ‘upright’. Loosen the lens adjusting screws and adjust the lens to obtain the desired field of
view and focus.
Tilt lock
2 places
Lens adjustment
Focus adjustment
4. Lock the lens and tilt screws. Put the dome cover back and align the clear window in the dome
cover with the lens. Attach the dome cover to dome base with the 4 mounting screws.
NOTE: The cover only goes on in ONE direction. There is a key and slot; if not aligned, cover will not
close properly.
NOTE: If you move the camera module, it is necessary to loosen the dome and liner and reposition
the liner so the lens points out through the slot, and the rubber seal presses onto the clear part of the
dome and not the liner. Loosen 4 Philips screws, reposition liner, then TIGHTEN four cover attachement
screws (else seal and vandal resistance is compromised).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EverFocus Electronics Corp.
EverFocus Taiwan:
EverFocus Europe - Germany:
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: +886 2 2698 2334
TEL: +49 2822 93940
FAX: +49 2822 939495
FAX: +886 2 2698 2380
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: +86 755 2765 1313
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: +86 10 6297 3336~39
FAX: +86 755 2765 0337
FAX: +86 10 6297 1423
EverFocus USA - California:
EverFocus USA - New York:
1801 Highland Avenue, Unit A, Duarte, CA 91010,
USA
415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA
TEL: +1 631 436 5070
TEL: +1 626 844 8888
FAX: +1 626 844 8838
FAX: +1 631 436 5027
EverFocus Japan:
EverFocus Europe - UK:
5F, Kinshicho City Building, 2-13-4
Koto-Bashi,Sumida-Ku, Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
Unit 12, Spitfire Business Park,
Hawker Road, Croydon Surrey, CR0 4WD, UK
TEL: +44 20 8649 9757 / +44 845 430 9999
FAX: +44 20 8649 9907
FAX: +81 3 5625 8189
EverFocus India:
Suite 803, Housefin Bhavan, C-21, Bandra Kurla
Complex, Bandra (East), Mumbai 400051, India
TEL: +91 22 6128 8700
FAX: +91 22 6128 8705
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
August 2013
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|