STEREO POWERED MIXER
PSX1000
PSX1600
PSX2200
OWNER’S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
FIRST OF ALL, WE WOULD LIKE TO THANK YOU AND CONGRATULATE YOU TO YOUR PURCHASE OF A ELECTRO-VOICE
POWER MIXER.
The design of the PSX compact power mixers is based on decades of experience, research and development as well client inter-communi-
cation in the professional audio market. With the PSX you own a power mixer that offers a wide range of functionality in a very compact frame.
All the troubling experiences with cabling and matching mixers, amplifiers, FX units, and equalizers is history. You now own a device with
optimally matched components.
The mixer’s ergonomic shape and clearly structured controls allow instant access at all times. Also during the transport you will quickly learn
to appreciate the PSX’s superiority: recessed handles on both sides, compact dimensions and low weight. Additionally, a sturdy dust hood
protects the controls against damaging.
Through its multiple functions, its high dynamic capacity, and extremely low-noise design in combination with the 18bit-Dual-Stereo effects
unit and the high-performance power amplifier, the PSX is best equipped for universal use. No matter, whether on-stage, in a home recording
environment or in a permanent installation, Electro-Voice’s PSX is the ideal partner to meet your expectations of a professional audio device
- effective and reliable.
Of course, you want to operate your new PSX as quickly as possible. But please, take your time to read about all connections, functions, and
controls, first. Every section is explained systematically and in detail within this owner’s manual: the input channels, the effects and the master
section as well as the built-in power amplifier. Through the careful perception of the manual you will learn a great deal about all functions and
find some useful and practical tips for the daily operation of the PSX. Even more important, you will find some adjustment instructions that
should be painstakingly carried out; plus the description of a typical sound reinforcement installation, the block diagram, specifications,
connection guidelines, etc... So, take your time and keep on reading.
UNPACKING AND WARRANTY
Open the packaging and take out the PSX. Detach the protective foil of the FX unit’s display. In addition to this owner’s manual you will find
the mains supply cord and the warranty card. Please check, if the warranty registration form is filled out correctly. Only when this form is
completed, you will be able to apply for warranty claims. We grant 36 months of warranty, starting with the date of purchase. Therefore, we
ask you to also keep the original certificate of purchase together with the warranty certificate.
INSTALLATION AND CONNECTIONS
Always install the PSX on an even surface to allow for sufficient airflow during the operation. The device is equipped with electronically
controlled fans to protect the power amplifier against thermal overload. The direction of the airflow is front to rear. Fresh, cold air enters the
mixer at its front side and warm air leaves the device through the ventilation louvres in the rear panel. Do not cover the frontal or the rear
ventilation louvres, since otherwise, the PSX would automatically enter the protect mode to prevent the occurrence of thermal overload. When
the protect mode is engaged, the device is not going to be damaged. But during this period of time regular operation is not possible.
Before establishing the mains connection, please make sure that the device matches the voltage and frequency of your local mains supply.
Check the label next to the mains switch. When switching the power on, the internal ventilators will run for about 2 seconds at full speed to
give you an acoustical signal that the PSX entered the operation mode. In addition dust particles that might have gotten into the enclosure
are blown out.
The SPEAKER OUTPUTS on the rear panel of the PSX are provided through professional standard Speakon connectors which offer an
absolutely secure connection. The pin assignment of these sockets is 1+ (hot) and 1- (cold).
3 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT/MONO
1. MIC
Electronically balanced XLR-type inputs for the connection of low impedance microphones, like the ones that are
featured in big studio -and live mixing consoles. This type of input stage provides extraordinary low- noise signal
amplification with extremely low distortion (typical <0.002%) even in the high frequency range.
Generally, any type of microphone can be connected as long as its pin assignment is
in accordance with the diagram shown aside. When condenser microphones are
connected, you have to press the PHANTOM button which is located in the master
section. The microphone gets its operational voltage (+24Vdc) through the mixer so
you can forget about battery replacement .
CAUTION: Make sure to always connect the microphones before turning on
the phantom power or switching the PSX on with phantom power activated. This is the only way to prevent your
microphones from damage. Also be sure to engage the stand-by button in the master section to prevent nasty
power-on transients.
The connection of condenser type microphones and dynamic microphone models at the same time is possible and
should generally not lead to any problems. Before you do so, please refer to the microphone’s manual to make
sure that this kind of operation is in accordance to the manufacturer’s guidelines.
The MIC input is designed for levels between –60dBu … +11dBu – depending on the setting of the corresponding
gain control. Because of their low impedance design and the phantom power these XLR-type inputs are not meant
for cascading other mixing consoles or the connection of FX units, keyboards or other electronic equipment. When
connecting this type of equipment, please use the LINE level inputs.
2. LINE
Electronically balanced inputs for the connection of electronic instruments, such as keyboards, drum machines,
electric guitars and basses with active outputs, as well as all other high-level signal sources, like additional mixers,
FX units, CD players, etc.
The LINE input is designed for levels between –40dBu and +30dBu. The connection of balanced or unbalanced
signal sources is handled with monaural or stereo phone plugs, wired according to the diagram below. If the device
that you want to connect has a balanced output stage, the use of balanced cables with stereo phone plugs is
preferable. This type of connection greatly lowers the induction of external noise or HF interference.
Do not connect signal sources to the MIC and the LINE inputs at the same time, since the signals would interfere
with each other, resulting in level reduction.
One more note: Please, do not connect electric guitars or basses with passive, high impedance outputs directly
to one of the LINE inputs. The LINE inputs of the PSX – like the line level inputs of mixers from all other
manufacturers – are meant for the connection of relatively low source impedance of electronic instruments or audio
equipment. The reproduction of the instrument’s original sound characteristics will be unsatisfactory – unless this
effect is intended. Those instruments should be connected using a special transformer, direct box or pre-amplifier
with very high input impedance. Musical instruments that are equipped with an active electronic output stage
(battery powered) can be connected without problems.
When connecting signal sources, please make sure that the corresponding channel faders or the master
faders are at their minimal settings or that the STANDBY button is engaged. This will save you, your
audience, and speakers from unpleasant pop noise.
3. INSERT
Stereo phone jack with breaker function. The low impedance output is assigned to the tip (send) and the high
impedance input (return) is assigned to the ring (body). This jack allows the connection of external compressors,
limiters, EQs, etc. into the corresponding channel’s signal path. The insertion point is post gain controls, low-cut
filters, and voicing-filter stage and pre-EQ section and faders. You have to use a stereo phone plug wired according
to the following diagram – in case you intend to use this jack as a true insert bus.
INSERT
4 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT/MONO
If you want to use this socket as a DIRECT OUT (Pre EQ), the stereo phone plug’s tip and ring have to be short
circuited, so that the audio signal is not interrupted. If you are using a monaural phone plug instead, you will get a
DIRECT OUT with breaker function – the signal flow within the channel is interrupted.
DIRECT OUT
4. GAIN
Rotary control to adjust the MIC/LINE inputs’ sensitivity. These controls let you optimally adjust the incoming signals
to the mixer’s internal operation level. Correct adjustment offers the benefits of improved S/N-ratio and provides
you with the full bandwidth of the PSX’s outstanding sonic capabilities. On the XLR-type connectors, amplification
of +10dB is achieved when the control is set all the way to the left and +60dB when the control is turned all the way
to the right. When dealing with very low input levels, like those that occur during vocal recordings or when the sound
source is located at a distance, the high gain is extremely beneficial. Using the LINE-input, the signal is generally
attenuated by –20 dB. The total adjustment range of 50dB stays the same. The LINE-input’s unity gain – no
amplification (0 dB) – is achieved at the 20dB mark.
The following is meant as a short note for your assistance on how to determine the correct input level:
Note on how to adjust the input level:
1. Set the gain control and the corresponding channel fader to their lowest setting.
2. Connect the desired sound source (microphone, musical instrument, etc.) to the MIC or LINE input.
3. Play the source at its highest volume –sing or speak as loud as possible directly into the microphone or play
the instrument.
4. While you are playing the sound source or singing into the microphone, adjust the input level using the gain
control, so that during the loudest passages the PEAK LED doesn’t blink, but the SIGNAL - LED
lights constantly.
This is the basic channel setting, gives you at least 6dB of headroom, which means you have at least 6dB
before signal clipping. In case you intend to make further adjustments to the channel’s EQ setting, you should
perform the steps 3. and 4. again, since changes in the sound shaping section also influence the channel’s over-
all level.
5. LO CUT 80 Hz
When the LO CUT switch is engaged, frequencies below 80 Hz are attenuated (18 dB-per-octave). In most cases
using the LO CUT filter with microphone channels is a good advice, since it efficiently suppresses popping sounds
and rumbling noise. The only exceptions are kick drum and
acoustic bass.
Sometimes it can be also very effective to combine the LO
CUT filter with the VOICING filter. For instance to provide a
“thin” voice with more “body”, without getting additional low-
pitched noise. Whenever the LO CUT is engaged, raising the
bass level (LO EQ) provides you with a richer sound, but
without additional rumbling or popping noise.
Another welcome side effect is, that the power amplifier and
the connected loudspeakers do not get “polluted” with unne-
cessary low-pitched noise. And the audience will be thankful
for the use of the LO CUT filter, too, since they can enjoy a
truly clear, natural, and powerful sound performance.
6. VOICING FILTER
This button activates an asymmetric microphone filter, which
can be used in addition to the channel EQ. The VOICING
filter enhances the first harmonics of the human voice and
slightly attenuates the mid frequency range. This voice sha-
ping method provides precisely audible, intelligible, and po-
werful vocals that are clearly emphasized from the rest of the
mix and is not achievable using ordinary third or octave
equalizers.
The use of this filter is not restricted to vocals only. Horns,
woodwinds, and other acoustic instruments can also profit
from the voicing filter.
We leave it entirely up to your creativity to try the filter with
as many different sound sources as you like. Normally, you
do not have to worry about the occurrence of feedback.
5of32
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT/MONO
7. EQ SECTION
The mixer’s EQ section allows shaping of the audio signal within different frequency bands. Turning one of the
EQ level controls to the right enhances/amplifies the corresponding frequency range while turning them to the left
lowers/attenuates the signal of the specific frequency band. Before you begin to alter the sound, all EQ controls
should be set to their neutral position; that is: their detented, center position. Try to avoid setting the EQ controls
to extreme positions. Usually, minor changes are totally sufficient and produce the best results in the overall mix.
You should use natural reproduction as an benchmark and rely on your musically trained ear, being the best
instrument to judge the sound quality. The moderate use of the MID control is the best remedy for avoiding
acoustical feedback. In this frequency range, you should try to avoid excessive enhancement. Lowering the level
in this band will provide you with high amplification with lower likelihood of feedback.
Use the LO control according to your pleasing, to add more “punch” to the sound of a kick drum or “body” to the
vocals. Use the HI control in the same way to provide cymbals and the human voice with more treble and a more
transparent sound. The MID EQ section offers separate rotary controls for the adjustment of the level (MID) and
the frequency band (kHz) between 800 Hz and 8 kHz.
LO-HI EQ
MID EQ
Adjustments in the MID range are certainly the most effective way to shape the sound. As a matter of fact,
determining the correct center frequency is not always as easy as it seems. Here is one method – amongst others
– how to quickly find the right setting of the parametric EQ for your application.
Note on how to adjust the parametric EQ:
1. Slightly lower the channel fader to avoid feedback.
2. Turn the MID rotary control all the way to the right (+15dB).
3. Play the desired sound source or talk into the microphone.
4. Meanwhile turn the frequency rotary control (kHz) slowly from left to right.
5. Quickly, you will detect the frequency range that is not to your liking or
causing feedback.
6. Leave the frequency control in this position and turn the MID control to the left until the
sound is natural or to your liking.
Enhancing a specific frequency range is a different story. In this case perform steps 1 to 4 as described above.
Set the frequency rotary control to the range you want to enhance or leave it at the position where the sound is
most satisfactory. Now you can use the MID control to determine the amount of alteration.
8. AUX/FX
The AUX/FX controls are used to adjust individual amounts of channel signals to be routed to the FX1 or the FX2
units. The split point of the “dry” signal is POST FADE or in other words: the signal path is split after the audio
signal has passed all stages of the channel module, including the volume fader. That is the reason why the fader
setting also influences the amount of the signal that is fed to the FX units. By using the AUX/FX controls, it is easy
to establish an effects mix. For example, you can assign the short reverb effect of the FX1 unit to the lead vocals
and a combined effect program – echo, hall, and chorus – via FX2 to the background vocals. To determine the
desired intensity of each effect, you should start with the controls set at their center and make individual adjustments
from there on. Also keep in mind that there are two AUX/FX1/2 send controls located within the master section
which control the total amount of the FX signals. When you begin to establish the effect mix these controls should
also be set at their center position.
In case you are not using the internal FX units and/or you want to connect external signal processing units, the
pre-mixed AUX/FX1/2 signals are outputted via the AUX1/2 send jacks. Please monitor the PEAK LEDs in the
FX1/2 channels. The indicator should only light briefly at the occurrence of high program peaks. If the indicator is
constantly lit, you should lower the send levels of those channels where the program peaks occur. For further
information, please read the paragraphs about the FX1/2 units.
6 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT/MONO
9. AUX 3
The AUX 3 control is primarily meant for the monitor mix. Nevertheless, when the master section’s AUX3 POST
button is pressed, it can also be used as a third FX send bus. In that case, the signal is split post-fader and outputted
via the AUX 3 send jack.
To establish a monitor mix you can choose between two alternatives. The main difference being the point where
the signal is split according to the setting of the AUX3 POST button.
If the AUX3 POST button is not engaged, the signal split is PRE FADER – the setting of the channel faders does
not affect the signal level that is present at the AUX3 rotary controls. Since the monitor mix is not influenced by
the setting of the channel faders, this alternative is primarily used when the main mix and the monitor mix have to
be completely different – the volume of specific musical instruments or vocals needs to be higher or lower or should
not appear at all in the monitor mix. This mode is also preferable when the PSX is operated by a engineer in the
audience area (front of house).
The other alternative should be used when you have to operate the mixer on-stage and still want to have control
over the main mix.
If the AUX3 POST button is engaged (LED is lit), the signal at the AUX3 rotary control is POST FADER – the signal
is split after it passes the channel faders and therefore is affected by their settings. Setting all AUX3 controls to
their center position, the main mix is also present on the monitor bus, giving you the opportunity to control the
volume settings individually from the stage. The overall volume of the monitor mix is set with the AUX3 fader in the
master section. If you are using this option you have to keep in mind that all volume changes made with the channel
faders also appear in the monitor mix, leaving you with a higher risk of acoustical feedback.
To reduce the risk of feedback, you still have the option to adjust the individual send levels via the channels’ AUX3
rotary controls. There is even the possibility to cancel some loud instruments – like the kick drum or the snare
drum, which are in fact already loud enough on-stage – totally from the monitor mix by turning the corresponding
controls all the way to the left.
10. PAN
This control determines the position of the connected sound source within the stereo image. When this control is
set at its center position, the audio signal is fed equally to the left and the right master busses. Through the extensive
PAN section circuitry the essential sound pressure level always stays the same, no matter to what position within
the stereo image the PAN control is set.
11. PFL
Engaging the PFL button (Pre Fader Listening) routes the audio signal of the corresponding channel to the
headphone bus. In this way you can route as many signals as you want to the bus at the same time. The volume
levels of the individual signals are not affected by the channel fader settings – PRE FADER LISTENING. This gives
you the opportunity to set the level or the EQ of a channel without the need to include it in the main mix. The overall
signal of the headphone bus is present at the headphone output.
12. SIGNAL (present) / PEAK indicator
These indicators play a key role during the level adjustment of the input channels, offering visual confirmation of
the actual signal level. They provide the possibility of detecting the risk of overdrive before you would actually hear
the distortion, unlike the mixers of many other manufacturers that either only provide a PEAK indicator or no channel
indicator at all.
As described before, the signal “present” LED should blink in the rhythm of the incoming signal. If this is not the
case, you should increase the gain. If the PEAK LED blinks frequently or lights up constantly, the corresponding
channel is likely to enter clipping and you should turn the gain control a bit to the left. The signal “present” LED
lights at levels –30dB below clipping while the peak LED lights at a level of –6dB below the occurrence of overdrive.
It is also a good idea to watch the indicator during a performance. During performances, some musicians get carried
away by the music and the atmosphere and tend to play their instruments more dynamic than during the rehearsal.
This, of course, can easily lead to channel clipping, resulting in degradation of the sound.
13. VOLUME
The channel faders are used to set the volume of the corresponding channels and to establish an accurately
proportioned mix. The channel faders should be positioned within the range of –5dB to 0dB, leaving you with a
degree of control that allows the precise matching of relatively large differences in the channels’ level settings. The
overall volume is set through the use of the master faders.
Even though the channel faders offer an additional gain of +10dB, we would recommend that you not exceed the
+5dB mark. If the PSX’s main bus gets “overloaded” with too many “high level” input channels, despite its special
negative gain structure, the summing amplifier could be driven into clipping. Once you reach a level where some
channel faders are set above the 0dB marking, we would recommend you lower the setting of each channel fader
by about –5dB and increase the overall output level by elevating the master faders. The proportion of the mix and
the overall volume stay the same while the risk of clipping is prohibited.
7of32
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT/STEREO
Since most features of the stereo inputs are virtually identical to those of the monaural inputs, we will not discuss
their functions in detail again. Thus, we only point out the differences and ask you to refer to the paragraphs in the
first chapter of this owner’s manual.
14. MIC
Like their monaural counterparts the stereo input channels of the PSX incorporate
extensive circuitry and electronically balanced XLR-type connectors for the connec-
tion of low impedance microphones. Whether your setup is more microphone-ori-
ented or you have more line level sound sources to connect, you can always use
the full amount of input channels, provided by your PSX. The functioning principles
were already discussed in detail in the previous chapter.
15. STEREO INPUT L/MONO R
Electronically balanced inputs for the connection of musical instruments with stereo output, like keyboards and
drum machines, Electric guitars and basses with an active outputs, as well as all other equivalent sound sources
with high level outputs, like additional mixing consoles, FX units, CD players, etc.
The stereo LINE input is meant for balanced or unbalanced sources with levels between –20dBu and +30dBu. For
the connection of external devices you can use monaural or stereo phone plugs which are in accordance to the
diagram below. If the external device is equipped with a balanced output stage, you should preferably use balanced
cables and plugs, since this type of connection provides better shielding against HF induction and external noise.
In case you want to connect a monaural source to a stereo input channel, plug it into the L/MONO input. The signal
gets internally routed to both channels. For further information, please refer to the chapter “INPUT/MONO”.
16. GAIN MIC
Rotary control to adjust the MIC inputs’ sensitivity, providing the possibility to optimally match the incoming signals
with the mixer’s internal operation level. The MIC GAIN control is only active for the XLR-type connections of the
stereo input channels.
Adjustment and functioning of these controls are identical to those of the monaural inputs.
CAUTION: The MIC GAIN control of an unused microphone input should always be set to its minimal marking.
Otherwise the noise of the inactive input is added to the audio signal of the corresponding LINE input, which could
lead to unnecessary extra noise at the main output, becoming clearly audible in program breaks.
17. LINE TRIM
These rotary controls are used to match the incoming line level signals with the operational level of the PSX. The
total adjustment range is 30dB. Unity gain – no amplification (0 dB) – is achieved at the 0dB mark. The control
offers a level reduction of the incoming signal by –20dB and an amplification of +20dB. This range is wide enough
to allow the connection of most professional, semi professional, and even hi-fi audio sources.
For further details on how to adjust the LINE TRIM control, please refer to paragraph 4. GAIN.
If you use a keyboard as sound source on one of the stereo inputs, make sure that no split zones or layers with
channel separation are activated. Otherwise the stereo channel mapping will appear like it is set on the keyboard
and you will not have the opportunity to re-position the sound in the overall stereo image, using the controls of the
mixer. The better alternative to connect a keyboard with pre-programmed channel mapping is to use two adjacent
monaural input channels, leaving you the option to place the sound in the final mix via PAN controls.
One more tip, in case you desperately need another input and all channels of the PSX are already in use:
The microphone input and the phone plug-type inputs are electrically separated from each other. Each input is
equipped with its own gain control – respectively trim control, providing you with the possibility to connect a LINE
level source in addition to a microphone. Of course, the two sources share all other controls. Consequently,
separate adjustments are not possible. This option is only meant as a subsidiary function and can be used when
there is absolutely no other alternative.
8 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT/STEREO
18. EQ SECTION
The mixer’s EQ section allows very differentiated shaping of the incoming audio signal within miscellaneous
frequency bands. Turning one of the EQ level controls to the right enhances/amplifies the corresponding frequency
range while turning them to the left lowers/attenuates the signal of the specific frequency band. Before you begin
to alter the sound, all EQ controls should be set to their neutral position; that is: their marker points straight up
(locked in place). Try to avoid setting EQ controls to extreme positions. Usually, minor changes are totally sufficient
and produce the best results in the overall sound. You should use the natural reproduction as an orientation mark
and rely on your musically trained ear to judge the sound quality. The moderate use of the MID control is the best
remedy to avoid acoustical feedback. In this frequency range, you should try to avoid excessive enhancement.
Lowering the level in this band will provide you with high amplification rates without feedback.
The HI and LO controls of the STEREO channels’ EQ section provide a degree of control that is equally adequate
for LINE level inputs and microphones. The MID control is active in a comparably wide frequency band around 2.4
kHz. With most microphones this is the critical range, where a slight attenuation offers excellent results.
19. AUX/FX
These controls determine the amount of the summed L/R signal that is send to the AUX/FX bus. The signal routing
is POST FADER. For more details on the functioning of these controls, please refer to the INPUT/MONO section
of this owner’s manual.
20. AUX3
This control determines the amount of the summed L/R signal that is send to the AUX3 bus. Depending on the
setting of the AUX3 POST switch within the PSX master section you can choose if the signal is routed PRE or
POST FADER.
21. BAL
The function of the BAL control of the stereo channels is equivalent to the PAN control’s function of the monaural
channels. If you turn the rotary control all the way to the right, the signal is routed to the right output while the signal
of the left channel is muted. When the control is set to its center position, the signal is present with equal intensity
at the corresponding L/R outputs. Whenever stereo sound sources are connected to a stereo channel, you should
leave the BAL control at the center position or make only minor adjustments in either direction. In case a microphone
or another monaural sound source is connected, the BAL controls function absolutely identical to the PAN controls
of the monaural input section.
22. PFL
Engaging the PFL button routes the audio signal of the corresponding input channel to the headphone bus where
the stereo signal is outputted to the headphone output. You can route as many channels as you want to the bus
at the same time. The volume levels of the individual signals are not affected by the setting of the corresponding
channel faders – PRE FADER LISTENING. This gives you the opportunity to set the level and the EQ of a channel
without the need to include it in the main mix.
23. SIGNAL/PEAK
For the stereo SIGNAL/PEAK indicator function, the left and the right channels are monitored separately. The
respective highest level reading is indicated, assuring that neither one is already driven into clipping. For further
descriptions on how to use this indicator most efficiently, please refer to paragraph 12 of the previous chapter.
24. VOLUME
The channel fader is used to simultaneously adjust both channels of the stereo signal. Functioning and specifica-
tions are totally similar to the monaural channel fader, as previously described.
9 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
EFFECT 1/2
FX1/FX2
The PSX offers two independent, identically-configured 18-bit stereo effect units – FX1 and FX2. Each unit
provides 99 program presets which are selected by the use of the UP/DOWN buttons. The presets are
divided according to the different effect types into seven different groups which are shown on the printed
labels. The programs within each preset group are sorted in ascending order where higher numbers provide
the same FX type with increased intensity. The presets 1 - 20 offer high quality reverberation effects that
are equally suited for the use during live performances or your home recording environment. The program
numbers 21 - 40 provide mixed effect types of echo/reverb, chorus/reverb and flanger. Numbers 41 - 60
offer different delay effects. The last group from 61 - 99 provides different reverse, chorus, and doubling
presets as well as special delay and reverb programs. During the initialization of the FX units, when turning
the PSX’s power on, the preset 05 (Large Hall 3 Bright) is selected for the FX1 while the FX2 unit is set to
preset 55 (Delay Mono 250ms). These two effects are similarly suitable for live performances and recording
applications. They can be used separately or together. Please, also refer to the supplementary information
form “EFFECT PRESETS” for a more detailed description of all effect presets. This list contains all preset
groups together with the corresponding program profiles, their individual characteristics, and a description
on how and in what combination to use them. Take your time to test all presets and select the ones that
are best suited for your specific application.
The preset 0 is a slap back echo which is mainly used for service and testing of the effects section and it
doesn’t appear on the list at the panel.
The FOOT SWITCH connector is provided to allow the connection of a foot switch pedal to remote control
the FX units’ EFFECT ON/OFF function. If your foot switch features a LED – like the EV FOOT SWITCH
does – this indicator will light when the effect is activated.
FX1/FX2
1.......10
11.......20 21.......30
31.......40
41.......50 51.......60
61.......99
REVERB
HALLS
REVERB
PLATES
ECHO
REVERB
CHORUS
REVERB
DELAY
STEREO
DELAY
MONO
SPECIAL
PROGRAMS
25. AUX1/2 SEND
These jacks are meant for the connection of external FX units, providing the signal mixes that you have
established for the AUX/FX buses – the identical mixes which are fed to the internal FX1/2 units. The output
level is controlled using the corresponding AUX/FX SEND controls. The external devices’ output signals
can be send back to the PSX via the stereo return bus or by using stereo input channels.
The AUX1/2 sends are designed with Ground Sensing technology to prevent the induction of external noise,
even when longer cables are used.
26. DISPLAY
The actual selected effect number is displayed.
27. UP/DOWN buttons
The UP/DOWN buttons are used to select the effect presets. Keeping a button pressed constantly lets you
step quickly through the program numbers.
28. FX to AUX3
These controls allow to mix the FX1/2 output signals with the AUX3 signal. In case you are using the AUX3
bus for monitoring purposes, you are able to add the FX signals at the desired level to the monitor mix.
Experience in mixing has shown that the effect level in the monitor mix should be lower than the level in
the main mix. R
29. AUX/FX SEND
These rotary controls could also be called FX SEND master controls, since they are used to adjust the
overall level of the effect mix that you have established using the channel FX send controls. The AUX/FX
SEND controls are used to set the input levels of the corresponding FX unit, respectively and the levels of
the AUX SEND outputs. Whenever the Peak LED (PK) blinks, there is the potential risk that the FX input
signal is driven into clipping, making it necessary to reduce its level by turning the corresponding AUX/FX
SEND control to the left, until the LED is not lit anymore. Since the AUX/FX SEND controls not only affect
the signals of the FX buses but also the monitor effect level, which is sent by the FX to AUX3 control,
careless changes can result in acoustical feedback.
10 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
EFFECT 1/2
30. FX ON
These switches are used to turn the internal FX units on – the green LED is lit. Please keep in mind that
you also can use an external foot switch to turn the FX units on. In this case the LED also shows the
actual state of operation. If you want to use a foot switch, the FX ON switch has to be engaged first. The
corresponding FX unit is activated and you can use the foot switch to turn the selected effect program
on or off.
31. PEAK LED
These indicators show if the input stages of the internal FX units or the AUX 1/" SEND signals are driven
into clipping. To achieve an adequate S/N ratio, please adjust the FX units’ input level as follows:
Note on how to adjust the FX input signal:
1. Establish a “dry” mix – without effect settings – according to the previous descriptions.
2. Set the AUX/FX send controls of the effect channels to their center position.
3. Position the effect return faders of the effect channels at the –5dB marks.
4. Use the UP/DOWN buttons to select the desired FX program preset.
5. Press the FX ON switch.
6. Play the sound source of the desired input channel and adjust the desired
amount of the FX signal, using the AUX/FX controls of this input channel.
Repeat this step for all input channels that you want to include in your effect mix.
7. Adjust the AUX/FX SEND controls, so that the Peak LED only lights frequently
at highly dynamic signal peaks.
8. Use the FX to AUX3 control to add the effect mix to the monitor mix. Use the
FX return faders to add the desired amount of the FX signal to the main mix.
In case you are using a different effect setting for the second FX unit, you have to repeat the step 2 - 8,
respectively. Pay some attention to the peak indicators when operating your PSX to quickly interact when
the signal levels exceed the normal range and enter clipping.
32. EFFECT RETURN
These stereo faders are used to determine the effect amount of the main mix. In case you have to set
these faders at a position above the +5dB mark, please check if the FX units input signals are adjusted
properly. Otherwise use the AUX/FX SEND controls to increase the input levels.
11 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
AUX 3
Typically, the AUX3 channel is used as monitor bus. Depending on the setting of the AUX3 POST switch, it is also
possible to configure the bus for the connection of an additional, external FX unit.
33. AUX3 SEND
This output is meant for the connection of an external FX unit, a power amplifier or active stage monitor speaker
systems, when the AUX3 bus is used for monitoring purposes. Using the AUX3 fader, the output level can be adjusted
over a wide range up to +20dBu. The AUX3 send is designed with Ground Sensing technology to prevent the induction
of external noise, even when long cables are used.
34. FEEDBACK FILTER
The feedback filter is a very narrow band notch filter which is only active over a range that is extremely susceptible
to acoustical feedback. The frequency band is set using the corresponding rotary control. The filter is activated by
pressing the corresponding ON switch. Acoustical feedback occurs when the sound system becomes the largest
acoustical source at a microphone. Or in other words: the speaker signal hits the microphone and gets amplified again
and again, resulting in escalating oscillation, and is audible as a high pitched whistle or loud humming sound. The
following guidelines are meant to assist you in avoiding feedback and you should take them into consideration even
before you activate the feedback filter.
1. Do not position the main speaker systems behind the microphones.
2. Turn off all unused microphones.
3. Also consider the microphones’ different polar patterns and characteristics, when placing
the monitor speakers.
4. Do not turn up the monitor system’s volume higher than really necessary.
5. Try to avoid extensive equalization on channels that you want to include in your monitor mix.
6. Keep in mind, that microphones “behave” different when somebody stands right in front of
them. In fact, the amount and intensity of first reflections changes things drastically.
7. Position the microphones as close as possible to the sound source.
If you still need more volume from the monitor system, after trying the above mentioned precautions, you can use
the feedback filter to notch the frequency that tends to affect feedback the most. Therefore, you need to perform the
following steps:
Increase the AUX3 (monitor) level until the point where feedback starts. The “sound” you hear is generated within the
system. Turn on the feedback filter and adjust the rotary control at the point where the “ringing” disappears. Switching
the filter on and off lets you easily check if you tuned in the correct frequency. The feedback filter attenuates the
corresponding frequency band by about 9dB. Since the filtered band is extremely narrow, an alteration in the sound
of your monitor system is hardly audible.
CAUTION: Please be extremely careful when you increase the level up to the feedback limit. Careless operation,
resulting in feedback at high SPL, can severely damage your speaker systems and – even more important – the
human ear.
35. AUX3 POST
As mentioned before, this switch determines if the AUX3-mix signal is PRE or POST FADER. When the switch is
engaged and the yellow LED lights, the signals of all AUX3 controls in the input channels are sent after their
corresponding channel faders.
36. PFL
With this button you can route the pre-fader AUX3 signal to the headphones bus. The signal is outputted via the
headphone output. The setting of the AUX3 fader is not relevant for the signal’s volume (PRE FADER LISTEN),
leaving you with the opportunity to adjust its level and equalization without the need to route it to the AUX3 SEND
bus.
37. AUX3 VOLUME
This fader controls the AUX3 SEND output level. When the AUX3 bus is used for monitoring, this fader lets you control
the volume of the monitor system.
12 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
MASTER
49. MAIN INSERTS
Stereo phone jacks for the left and the right channels with breaker function. The low impedance output
is assigned to the tip (send) and the high impedance input (return) is assigned to the ring of the
connector. This jack allows the connection of external EQs, compressors, limiters, etc. into the master
L/R signal path. The insertion point is pre-master faders. As with the inserts of the monaural input
channels, different DIRECT OUT functions can be accomplished.
Please, also refer to the corresponding section in the description of the MONO INPUTS.
50. MAIN OUTPUTS
The signals at the MAIN OUTPUTS are post master fader and mainly meant to feed additional,
external power amplifiers. Through these outputs, it is also possible to run a two-way active system
set-up. In this case, the active crossovers – or active subwoofers have to be connected to the MAIN
OUTPUTS. If you want to use the internal power amplifier to supply the high frequency cabinets, the
high-frequency signal coming from the crossover has to be run back into the PSX via the POWER
AMP INPUTS.
51. EQ INPUTS / OUTPUTS
The EQ INPUTS are provided through electronically balanced phone jacks with breaker function.
When inserting a phone plug, the signal path is interrupted between the master L/R controls and the
internal power amplifier. The EQ INPUTS and POWER AMP INPUTS are the only active inputs for
the internal power amplifier.
The signals at the EQ OUTPUTS are post-master fader and post the internal 7-band equalizers.
Likewise, the MAIN OUTPUTS can be used for connecting external devices.
52. POWER AMP INPUTS
The POWER AMP INPUTS are also provided via electronically balanced phone jacks with breaker
function. When inserting a phone plug, the signal path is split between the master and the internal
power amplifier. The POWER AMP INPUTS are then the only active inputs for the internal power
amplifier.
NOTE: For detailed information on the function and operation of the “MASTER PATCHBAY” – MAIN
INSERTS, MAIN OUTPUTS, EQ IN/OUTPUTS, and POWER AMP INPUTS – please refer to the
corresponding section; later in this owner’s manual.
53. FX1/2 FOOTSW.
Phone jack for the connection of the foot switch or other compatible unit, to switch the internal FX
units on or off.
To accomplish this function, the switches FX1 and FX2 have to be engaged.
54. LAMP
This XLR-type socket provides a DC voltage of 12V /2.4 watts and is meant for the connection of a
gooseneck lamp. Please make sure that the lamp used complies with the specifications and pin
assignment. shown here. CAUTION: Overload or short circuits can result from damaging this output.
To prevent this from happening, we recommend the use of a Littlelite gooseneck lamp, available from
your Electro-Voice dealer.
For further information, please consult your dealer.
15 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
MASTER
55. POWER AMP STATUS indicators
These indicators inform you about the momentary operational status of the PSX’s internal
power amplifier.
The POWER ON indicator is always lit when the PSX is in operational mode. If the LED is not
lit after you have turned the power on, please make sure that the PSX’s power cable is correctly
plugged in. If this is the case and the LED is still not lit, please contact your dealer.
The LIMIT indicator signals that you are operating the PSX at the internal amplifier’s limit.
Frequent blinking of the LED is acceptable, since the amplifier’s incorporated limiter prevents
serious distortion. Continuous illumination indicates that you should be aware of a degradation
in sound quality. In that case, the master level should be reduced.
The PROTECT indicator is lit when one of the PSX ’s extensive protection circuits is guarding
against thermal overload, HF-induction, DC at the outputs, or short circuits is activated. When
the PSX is in protect mode, the speaker outputs are muted and the amplifier’s inputs are
shorted to prevent the amplifier from being damaged. In this case you should first check to
see if the ventilation louvres are blocked. Another cause could be that you have more than
three 8 ohm speaker systems per output channel connected. You should also disconnect the
SPEAKON output connectors and check the speaker cables for short circuits.
During normal power-on operation, the PROTECT LED always lights for about two seconds,
signaling that the PSX’s protection circuitry is operational.
56. PHANTOM POWER
When this switch is engaged, all MIC inputs are supplied with +24V phantom power.
Please make sure prior to engaging phantom power that the PSX is switched off or in
stand-by mode. With active phantom power the connection of unbalanced signal
sources (keyboards, mixer, etc.) to XLR inputs is not advisable, because this could
lead to severe damaging of your equipment.
ATTENTION! IMPORTANT NOTICE!
In general, the operation of phantom-powered condenser microphones and balanced
dynamic microphones at the same time does not lead to any problems.
Nevertheless, some balanced dynamic microphones are extremely sensitive to this.
Some models could get damaged when used on mixers with active phantom power.
Please refer to the microphones’ owner’s manuals to make sure that this operation is
permissible.
To be on the safe side, you should switch the PHANTOM POWER off, when using
balanced dynamic microphones, only.
57. 7-BAND EQUALIZER
The respective EQ ON switches activate each 7-band graphic EQ within the PSX’s master
section. The EQ’s insert point is post master fader and pre internal power amplifier. The EQ
is bypassed when the EQ ON switch is not locked in its “ON” position. The two graphic EQs
provide seven frequency bands, each. Through these faders you are able to match the overall
sound optimally to the acoustic conditions of different locations or shape it according to your
personal taste. Each frequency band allows ±10dB equalization in the corresponding range
with a Q=1.4.
16 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
MASTER
The frequency ranges and the characteristics of the of the equalizer were carefully chosen
for live sound. If you want a clear and intelligible sound, which also provides cymbals and other
instruments with added high frequency detail, you should raise the levels of the 8kHz or 16kHz
bandsabit.Ifthemidssoundtoonasal,youshouldattenuatethe1kHzand2.5kHzfrequencies
a few decibels. To provide the kick drum or other bass instruments with more punch, you have
to boost the low frequency range, using the 80Hz or the 250Hz controls. In case the overall
sound is undefined with too much bass, lowering the levels of these two frequency bands will
solve the problem.
When using the equalizer, you should be aware of the fact that in most cases less adjustments
(especially boosting) provides better results. Thus, your first choice should be to establish the
mix using only the input channel EQs tosee if you can get satisfactory results. If so, you can
use the graphic EQ for the AUX3 (monitor), where in most cases it is more needed. You will
find the description of how to include the graphic EQ in the monitor bus later in this owner’s
manual.
58. MASTER LED-DISPLAY
The PSX offers two 10-segment LED ladders to monitor the output levels of the L/R master
signals. The indication range of the LED-meter is 33dB, displaying the levels in dBu which
are present at the EQ OUTPUT and the POWER AMP INPUT. The meter’s 0dB mark is
referenced to a 0dBu output signal at the POWER AMP INPUT. Increasing this level leads
to the power amplifier’s maximum input level of +6dB – equaling an output power of 500 watts
at 4 ohms per channel. Higher levels are not displayed, since the amplifier’s processor limits
the signal at this point. When the LIMIT LED of the status indicator section lights, this shows
that the internal limiter is activated.
59. PFL MASTER
When the master PFLbutton is engaged, the PRE FADER stereo master signal is routed to
the headphones output. The volume of this signal is not affected by the setting of the MASTER
faders.
60. MASTER L + R
Level controls to adjust the output signals of the left and right main outputs (MASTER).
Please make sure that the corresponding input channel fader or the master faders are
set to their minimum position or the STANDBY switch is engaged, before connecting
an external source to an input of the PSX. This will save you, your audience, and
speakers from unnecessary stress.
POWER AMPLIFIER
The PSX’s PROCESSOR-CONTROLLED stereo power amplifier’s design uses bipolar out-
put devices to provide a nominal output power of 500 watts at 4 ohms per channel. The
minimal load impedance of 2.7 ohms allows the operation with a maximum of three paralleled
8 ohm loudspeakers connected to each channel. Their low distortion provides the amplifier
of the PSX with outstanding sound quality that welcomes comparisons with the best profes-
sional high-end, stand-alone audio power amplifiers.
The amplifier is also designed to handle the wear and tear of touring operation. It incorporates
protection against thermal overload, short circuit, HF-interference or the occurrence of DC at
the outputs. Further protection against dangerous back-EMF is provided by a special circuit.
When the PSX is switched on, a relais control switching on of the power outputs. The internal
fans run shortly on full speed, signaling acoustically that the PSX is operational. A limiter
controls the initial current inrush, preventing the mains fuse from being blown during power-
on.
The extensive comparator circuitry constantly monitors the input and output signals and
activates the internal limiters whenever a non-linear operational state is encountered. This
provides reliable protection of the connected loudspeaker systems against overload and
clipping. Even when the maximum input level is overridden, no distortion is heard on the
speaker outputs. The amplifier also incorporates EVI Audio-patented processors to eliminate
transient problems of typical sound reinforcement speaker systems and provides extraordi-
narily precise and powerful reproduction of low frequencies.
17 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD INSTALLATION
CABLING
The ac power cord comes with the PSX. The quality of all other cables are your responsibility. Carefully chosen high quality cables are the
best precaution to prevent problems during operation. The following wiring alternatives are recommended to provide a trouble free operation
of your setup.
SPEAKER CABLES
From our experience as a manufacturer of loudspeaker systems we’ve learned that flexible speaker cables with a rubber jacket (10 - 16
gauge, depending on length) used in combination with NEUTRIK SPEAKON plugs and sockets, are the best choice to guarantee optimal
connection of loudspeaker systems. In accordance to the corresponding diagram, the SPEAKON plugs are connected on the PSX rear panel.
You can also consider the use of 4-wire cables where pins 2+ and 2- are also connected. This provides you with the possibility of using these
cables with active 2-way system configurations, as well. Professional-quality speaker cables with SPEAKON connectors and all other cables,
plugs, and sockets are available at your Electro-Voice dealer.
LF-CABLES – BALANCED OR UNBALANCED?
For all low current wiring , your best choice are balanced cables (2 signal conductors + ground shielding) with XLR-type connectors or with
stereo phone jacks and plugs. The cables should be step proof, shielded, and never longer than really needed. Too many too long cables
mostly lead to confusion and generate unnecessary problems.
Of course, you can also connect unbalanced cables with monaural phone plugs to the PSX’s inputs and outputs and because of its superb
grounding managing system in most cases no interference will occur. Still, there is a minimal risk that problems could arise and we believe
that this is reason enough to keep on reading. Generally spoken, if you have the choice, a balanced LF-cable is always the better solution.
Today’s modern audio equipment – like amplifiers, equalizers, FX units, mixing consoles, and even some keyboards – offers balanced in-
and outputs. In a balanced signal path the cable screen provides the gapless connection of all metal parts, offering efficient shielding against
the induction of external noise. The balanced cabling in conjunction with the common-mode rejection of the PSX’s input stage effectively
eliminates even existing artifacts of interference. All inputs of the PSX provide balanced audio connections and high common-mode rejection.
The mixing stage outputs – AUX, MAIN, EQ, etc. – are laid out in GND-SENSING technology – a special pin assignment of the output jacks,
offering all advantages of the balanced signal transmission, but lets you also connect monaural phone plugs without a problem. Nevertheless
– as mentioned above – when longer cables are involved, using stereo phone plugs and balanced cables are the better alternative. The
diagrams below show the pin assignments of plugs and cables that are used with the PSX.
balanced connection
of microphones
MIC INPUT
unbalanced
external equipment with
XLR-type in/output jacks
All phone jack in/out-
puts of the PSX
balanced
Direct OUT via INSERT,
uninterrupted signal path
Channel Insert
Main Insert
unbalanced
All phone jack
in/outputs of the
PSX
external equipment
with XLR-type in/out-
put jacks
balanced
Y-type cable for the
connection of external
FX units and signal
processors with phone
jacks
Channel Insert
Main Insert
19 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD INSTALLATION
In this chapter we would like to explain how to install a typical sound reinforcement system in passive configuration and incorporating stage
monitor speakers. The necessary equipment is:
1
1
2
2
2
2
4
1
PSX
Power amplifier for the monitor signal
Speaker Systems
Woofer cabinets
Speaker stands or 2 pole mounts
Stage monitor speakers
SPEAKON cables (8m), and 2 SPEAKON cables (2m)
Balanced LF-cable with a stereo phone plug on one side and an XLR-type connector on the other side
Setting up
·
·
Place the PSX and the external power amplifier in a way that allows their unobstructed operation during the sound check and performance.
Try to locate the best position to place the loudspeaker systems. If possible, the woofers should be placed on the floor while the cabinets’
most favorable position is above the woofer systems, on the same vertical axis. It is important that the lower edge of the is approximately
at the same height level as the heads of the audience. Either use the pole mounts for the top of the woofers or, in case this kind of
installation is not possible in your application, use separate speaker stands.
·
·
·
·
Do not place the left and the right speakers further apart than necessary. The less distance there is between the two speaker “clusters”
– the more impact to the sound.
Try to avoid positioning the main loudspeakers behind the line of microphones. If you have to run the system at higher sound levels, the
risk of feedback is very high.
When the microphones are placed and all musicians ready, place the monitor speakers facing the musicians. Make sure no microphone
is pointing directly into a monitor. You should also be aware of the individual characteristics of the used microphones.
Make all connections according to the diagram above. Use the different SPEAKON cables to connect the speaker systems to the PSX’s
power outputs, respectively to the power outputs of the external amplifier. Make sure not to confuse the channels by accident. using the
short SPEAKON cables, you can connect the Hi cabinets at the woofers’ outputs. The two monitor speakers are connected to either
output of the external amplifier. The amplifier should be run in a parallel mono configuration so that the amplifier’s volume controls provide
the capability to adjust the output levels separately.
·
·
Connect the PSX’s AUX3 SEND with the external amplifier’s input, using a balanced NF-cable with the stereo phone plug on one end
and the XLR-type connector on the other.
Connect all microphones to the monaural inputs of the PSX and the keyboards and other comparable sound sources to the rest of the
available inputs
20 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD INSTALLATION
·
·
·
Pull all faders down and engage the PSX’s STANDBY button to prevent unwanted feedback.
First, switch the PSX on and then the external amplifier.
In case you have condenser microphones connected to the PSX, you can now turn on the phantom power by pressing the PHANTOM
switch.
·
Activate the PSX’s by pressing the STANDBY button again.
SOUND CHECK
·
First, adjust the input levels of the microphones that are connected to the PSX. Please proceed as follows:
1. Set the corresponding gain controls and the channel faders to their lowest position.
2. Speak or sing as loud as possible into the microphone.
3. Use the gain control to adjust the level, so that even at loud passages the red PEAK LED is not lit but the
green SIGNAL present LED lights constantly.
·
Adjust the EQ of the monaural input channels:
1. Slide the channel fader and the master faders up a bit, so that the sound is heard coming from the main
speakers.
2. Turn the MID control carefully all the way to the right (+15dB). You should not hear any feedback.
3. Play the sound source or speak into the connected microphone.
4. Turn the frequency control (kHz) slowly from left to right.
5. You will detect the frequency range that is not to your liking or causing the feedback.
6. Leave the frequency control in this position and turn the MID control to the left until the sound is natural or to your liking.
7. If necessary, adjust the Hi and LOW controls, starting from their centered position, until the sound is pleasing to you.
8. Repeat the steps 1 - 7 for all monaural input channels in use.
·
·
In case you are also using the stereo input channels, you can adjust the levels in a similar way:
1. Set the LINE TRIM controls, the MIC gain controls, and the channel fader to their lowest setting.
2. Play the corresponding sound source at the highest volume that is to be expected during the performance.
3. Use the LINE TRIM control to adjust the level, so that even at loud passages the red PEAK LED is not lit but the green SIGNAL
present LED lights constantly.
Adjust the EQ of the stereophonic input channels:
1. Slide the channel fader and the master faders a bit up, so that you can hear the sound through the main
speakers.
2. Adjust the EQ controls at their center position.
3. Play the corresponding sound source.
4. Starting from the center position, you can adjust the controls until the sound is to your liking. Please, keep
in mind that major alteration of the EQ-setting does not necessarily result in the improvement of the overall
sound. Especially when sound shaping is concerned, less can be more.
5. Repeat the steps 1 - 4 for all stereo input channels in use.
·
·
If musical instruments are connected directly to the monaural inputs, follow the descriptions above for adjustment of the microphones.
Make sure, that all channel faders, gain controls, and LINE TRIM controls of unused input channels are at their minimal setting. In this
way you avoid unnecessary noise.
21 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD INSTALLATION
MAIN MIX
·
·
·
Position the master faders in the range between –30dB and –20dB.
Establish a basic mix, using the channel faders, so that the individual sound levels relate to each other according to your personal taste.
The best range for the channel faders to be set to is in the area of –5dB to 0dB. In this way you are provided with enough tolerance for
later adjustments.
·
·
Use the master faders to adjust the overall volume.
In case you are using the FX units, please proceed like this:
1. Adjust the AUX1/FX1 send controls at their center position.
2. Adjust the FX1 return fader at the –5dB mark.
3. Use the UP/DOWN buttons to select the desired effect preset.
4. Press the FX ON button.
5. Play the sound source of the desired input channel and adjust the desired amount of the FX signal, using the AUX/FX controls
of this input channel. Repeat this step for all input channels that you want to include in your effect mix.
6. Adjust the AUX/FX SEND controls, so that the Peak LED only lights frequently at highly dynamic signal peaks.
If necessary, repeat steps 1 - 6 for the second internal FX unit (FX2).
MONITOR MIX
·
·
·
·
To successfully adjust your stage monitors, turn off your audience mix on the PSX but keep the on-stage mix alive.
Lower the setting of the AUX3 fader within the master section.
Engage the AUX3 POST button within the master section.
Adjust the AUX3 faders of all input channels that are momentarily in use at their center position. In this way the main mix and the monitor
mix are completely identical.
·
·
·
Push the AUX3 fader up until low-level feedback is heard.
Activate the FEEDBACK FILTER and adjust its control, so that the feedback disappears.
Use the AUX3 fader to reduce the AUX3 level by about –6dB. This will provide you with enough “headroom” to avoid feedback during
the performance, even when some microphone positions are changed for the worse.
·
Use the FX to AUX3 control to add the effects mix to the monitor without influencing the main mix.
Normally, the monitor mix uses a smaller amount of effects than the main mix.
Let the artists perform some and check the sound of the system from different angles and distances. If you come to the conclusion that some
corrections in the overall sound are necessary, activate the 7-band equalizer and adjust the sound to your liking. By doing so, you should
keep in mind, that during the performance the sound will be changed when the audience is present and has a major effect on the acoustical
condition of the room, the degree of first reflections, and the absorption of low frequencies. If possible, you should check the sound “in the
house” during the performance and – if necessary – adjust it to the changed conditions.
We wish you lots of fun and success with your new PSX mixer.
22 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
MASTER PATCHBAY AND INSTALLATION ALTERNATIVES
All inputs and outputs in the master section are referred to as the MASTER PATCHBAY.
The mixer’s LINE OUTPUTS, RETURNS, and INSERTS are found here. To provide you with a wide variety of connection possibilities, the
MASTER INSERTS, MAIN OUTPUTS, EQ INPUTS and EQ OUTPUTS, POWER AMP INPUTS, and the AUX SENDS and AUX RETURNS
can be independently connected with each other or routed to external devices. In the basic configuration – when no plugs are inserted into
any of the MASTER INPUT connectors – the signals are patched internally and fed to the internal power amplifier. Once you connect a plug
to the INSERTS, EQ INPUTS, or the POWER AMP INPUTS, the internal signal path is interrupted, providing you with the opportunity to
include external signals. We would like to show you some examples of how to use the MASTER PATCHBAY.
1. Connecting an external power amplifier:
If you need to connect more loudspeaker systems than the PSX is capable of handling directly or if you need more power, you have to use
an external power amplifier. Using NF-cables with phone plug-type connectors, you can patch the signal either at the MAIN OUTPUTS – pre
EQ – or at the EQ OUTPUTS – post EQ. In this configuration, the signal path to the internal power amplifier is not interrupted and the audio
signal is outputted to the speaker systems connected to each amplifier.
2. Connecting an additional mixing console:
If you need additional input channels, you have to connect an external mixing console. In doing so you can either use up another LINE INPUT
of the PSX or – as shown in the diagram below – connect the external mixer to the STEREO RETURNS. In combination with the PSX’s stereo
return control, the latter solution offers the additional benefit of matching the level of the additional console to the PSX’s operating level.
23 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
MASTER PATCHBAY AND INSTALLATION ALTERNATIVES
3. Using the internal power amplifier for monitoring or side-fill purposes:
In case you want to use an external power amplifier to drive your main speaker systems, the internal power amplifier can be used for monitoring
or side-fill purposes. Use short patch-cables to connect the AUX3 OUTPUT with the EQ INPUT L and the MONO OUTPUT with the EQ
INPUT R. This enables you to use the internal graphic equalizer to separately adjust the signals of the monitor and the side-fill output channels.
The volume of the main channels can still be controlled via the master faders. The monitor speakers’ volume is determined by the setting of
the AUX3 fader while the MONO-fader controls the volume of the side-fill channel.
4. Monaural sound reinforcement with monitoring:
If your application does not demand stereo audio, you can operate the PSX in mono. In that case you can use short patch-cables to connect
the MONO OUTPUT with the EQ INPUT R and the AUX3 OUTPUT with the EQ INPUT L. The right main output is used for the sound
reinforcement while the left main output carries the monitor signal.
24 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
MASTER PATCHBAY AND INSTALLATION ALTERNATIVES
5. Maximum amount of speakers in a passive configuration:
The PSX allows connection of up to three loudspeaker cabinets with an impedance of 8 ohms per channel. In other words: the internal power
amplifier is capable of driving a maximum of six 8 ohm speaker models. The following diagram shows how the speakers have to be connected.
6. Active stereo 2-way configuration:
In this example the internal power amplifier of the PSX is used to drive the Hi/Mid cabinets. An active cross-over is connected to the MAIN
OUTPUTS or the EQ OUTPUTS which carry the full-range signals. The LF-signal outputs of the crossover are connected to an external power
amplifier, driving the woofer cabinets. The signal of the crossover’s HF-signal outputs is fed into the PSX’s internal power amplifier via the
POWER AMP INPUTS. Compared to the passive configuration, the overall sound gains clarity and higher volume levels are possible, since
the Hi/Mid cabinets do not have to deal with the low frequency signals.
25 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Technical Specifications PSX Mixing desk in rated condition, Unity Gain ( MIC Gain 20 dB ), all faders position 0 dB, all pots in mid
position, Master fader + 6dB, amplifier rated output power into 8 ohms, one channel driven, unless otherwise specified.
Maximum Midband Output Power, 1 kHz, THD £ 1%
into 4 ohms
into 8 ohms
PSX1000
2 x 570 W
2 x 340 W
PSX1600
2 x 570 W
2 x 340 W
PSX2200
2 x 760 W
2 x 430 W
Rated Output Power, 20 Hz ... 20 kHz, THD £ 0.2%
into 4 ohms
into 8 ohms
2 x 500 W
2 x 250 W
58 Vrms
2 x 500 W
2 x 250 W
58 Vrms
2 x 700 W
2 x 350 W
63 Vrms
Maximum Output Voltage of power amplifier, no load
THD at 1kHz, MBW=80kHz
MIC input to Main L/R output, +16 dBu
Power amplifier input to Speaker L/R output
DIM 30, power amplifier
IMD-SMPTE, power amplifier, 60Hz, 7 kHz
Frequency Response, -3dB ref. 1kHz
Any input to any Mixer output
Any input to Speaker L/R output
Crosstalk, 1kHz
< 0.006%
< 0.05%
< 0.015%
< 0.15%
< 0.006%
< 0.05%
< 0.015%
< 0.15%
< 0.006%
< 0.05%
< 0.015%
< 0.15%
15Hz ... 60kHz
30Hz ... 40kHz
15Hz ... 60kHz
30Hz ... 40kHz
15Hz ... 60kHz
30Hz ... 40kHz
Fader and AUX-Send attenuation
Channel to channel
CMRR, MIC input, 1kHz
Input Sensitivity, all level controls in max. position
MIC Input
> 80 dB
> 70 dB
> 80 dB
> 80 dB
> 70 dB
> 80 dB
> 80 dB
> 70 dB
> 80 dB
-74 dBu (155 µV)
-74 dBu (155 µV)
-74 dBu (155 µV)
Line Input (Mono)
Line Input (Stereo)
-54 dBu (1.55 mV) -54 dBu (1.55 mV) -54 dBu (1.55 mV)
-34 dBu (15.5 mV) -34 dBu (15.5 mV) -34 dBu (15.5 mV)
Power Amplifier Input
+ 6 dBu (1.55 V)
+ 6 dBu (1.55 V)
+ 6 dBu (1.55 V)
Maximum Level, mixing desk
MIC inputs
Line inputs
All other inputs
Record Send output
+ 11 dBu
+ 30 dBu
+ 20 dBu
+ 16 dBu
+ 20 dBu
+ 11 dBu
+ 30 dBu
+ 20 dBu
+ 16 dBu
+ 20 dBu
+ 11 dBu
+ 30 dBu
+ 20 dBu
+ 16 dBu
+ 20 dBu
All other outputs
Input Impedances
MIC
Insert Return
EQ Input and 2 Track Return
All other inputs
1.8 kohms
2.2 kohms
8 kohms
1.8 kohms
2.2 kohms
8 kohms
1.8 kohms
2.2 kohms
8 kohms
> 15 kohms
> 15 kohms
> 15 kohms
Output Impedances
Record Send
Phones
All other outputs
Equivalent Input Noise, MIC Input, A-weighted 150 ohms
Noise, Channel inputs to Main L/R outputs, A-weighted
Master fader down
Master fader 0 dB, Channel fader down
Master fader 0 dB, Channel fader 0 dB, Channel gain unity
Signal/Noise-Ratio, power amplifier, A-weighted
Equalization
1 kohms
47 ohms
75 ohms
-130 dBu
1 kohms
47 ohms
75 ohms
-130 dBu
1 kohms
47 ohms
75 ohms
-130 dBu
-92 dBu
-89 dBu
-83 dBu
104 dB
-92dBu
-87dBu
-81dBu
104 dB
-92dBu
-85dBu
-79dBu
106 dB
LO Shelving
± 15 dB / 60 Hz
MID Peaking, mono inputs
MID Peaking, stereo inputs
HI Shelving
± 15 dB / 100 Hz ... 8 kHz
± 12 dB / 2.4 kHz
± 15 dB / 12 kHz
± 10 dB
Master EQ, 2x7-band
Phantom Power
24V DC
24V DC
24V DC
Mains voltage
120V AC/50-60Hz 120V AC/50-60Hz 120V AC/50-60Hz
600 W 670W 1100W
508.5x210.3x478.7 667.5x210.3x478.7 826.5x210.3x478.7
Power Consumption at 1/8 maximum output power, 4 ohms
Dimensions, (WxHxD), mm
Weight, including lid
20 kg
24kg
29kg
Optional
Goosneck Lamp, 12V/2.4W, 12”, XLR
Footswitch FS11
Rack-Mount-Kit(PSX1000) NRS 90220
112 700
110 693
112 698
112 700
110 693
112 700
110 693
26 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
BLOCK DIAGRAM
27 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
Dimensions in mm (inch)
28 of 32
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY (Limited)
Electro-Voice products are guaranteed against malfunction due to defects in materials or workmanship for a specified period, as noted in the
individual product-line statement(s) below, or in the individual product data sheet or owner’s manual, beginning with the date of original
purchase. If such malfunction occurs during the specified period, the product will be repaired or replaced (at our option) without charge. The
product will be returned to the customer prepaid.
Exclusions and Limitations: The Limited Warranty does not apply to: (a) exterior finish or appearance; (b) certain specific items described
in the individual product-line statement(s) below, or in the individual product data sheet or owner’s manual; (c) Malfunction resulting from use
or operation of the product other than as specified in the product data sheet or owner’s manual; (d): malfunction resulting from misuse or
abuse of the product; or (e): malfunction occurring at any time after repairs have been made to the product by anyone other than Electro-Voice
or any of its authorized service representatives.
Obtaining Warranty Service: To obtain warranty service, a customer must deliver the product, prepaid, to Electro-Voice or any of its
authorized service representatives together with proof of purchase of the product in the form of a bill of sale or receipted invoice. A list of
authorized service representatives is available from Electro-Voice at 600 Cecil Street, Buchanan, MI 49107 (616-695-6831) and/or Electro-
Voice West at 9130 Glenoaks Boulevard, Sun Valley, CA 91532 (213-875-1900).
Incidental and Consequential Damages Excluded: Product repair or replacement and return to the customer are the only remedies
provided to the customer. Electro-Voice shall not be liable for any incidental or consequential damages including, without limitation, injury to
persons or property or loss of use. Some states do not allow the exclusion or limitation of incidental or consequential damages so the above
limitation or exclusion may not apply to you. Other Rights: This warranty gives you specific legal rights, and you may have other rights which
vary from state to state.
Electro-Voice Electronics are guaranteed against malfunction due to defects in materials or workmanship for a period of three (3) years
from the date of original purchase. Additional details are included in the Uniform Limited Warranty Statement.
Specifications subject to change without notice.
600 Cecil Street, Buchanan, Michigan 49107, Phone 616/695-6831, Fax: 616/695-1304
TELEX/EVI Audio Canada, 705 Progress Ave. Unit 46 Toronto, Onatario, M1H 2x1, Canada , Phone: 800/881-1685, Fax: 877/522-2242
TELEX Communications A.G., Keltenstrasse 11, CH-2563 IPSACH, Switzerland, Phone: 011-41/32-51-6833, Fax: 011-41/32-51-1221
EVI Audio Deutschland GmbH, Hirschberger Ring 45, D-94315, Straubing, Germany, Phone: 011-49/9421-7060, Fax: 011-49/9421-706265
EVI Audio France S.A., Parc de Courcerin-Allee Lech Walesa, Lognes, f-77185 Marne La Vallee, France, Phone: 011-33/1-6480-0090, Fax: 011-33/1-6006-5103
EVI Audio Japan Ltd., 2-5-60 Izumi, Suginami-ku, Tokyo, Japan 168, Phone: 011-81/3-3325-7900, Fax: 011-81/3-3325-7789
EVI Audio (Aust.) Pty., Unit 23, Block C, Slough Business Park, Slough Ave., Silverwater, N.S.W 2141, Australia, Phone 011-61/2-648-3455,
Fax: 011-61/2-648-5585
EVI Audio (Hong Kong) Limited, Unit E & F, 21 /F., Luk Hop Industrial Bldg., 8 Luk Hop St., San Po Kong, Kowloon, Hong
(358 173) 18.01.2000
Download from Www.Somanuals.com. All Manuals Search And Download.
|