Design LED 72MKII
Elation Professional™
6122 S. Eastern Ave.
Los Angeles, Ca 90040
Rev. 09/15/2008 - visage
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
1. GENERAL INFORMATION
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and
reliable LED fixtures on the market today! The Design LED 72MKII™ has been designed to
perform reliably for years when the guidelines in this booklet are followed. Please read and
understand the instructions in this manual carefully and thoroughly before attempting to
operate this unit. These instructions contain important information regarding safety during
use and maintenance.
UNPACKING: Thank you for purchasing the Design LED 72MKII™ by Elation Professional®.
Every Design LED 72MKII™ has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that may have occurred
during shipping. If the carton appears to be damaged, carefully inspect your fixture for
damage and be sure all accessories necessary to operate the fixture have arrived intact. In
the event damage has been found or parts are missing, please contact our customer support
team for further instructions. Inside the box you should find: the fixture, a DMX XLR cable, a
safety cable, and this manual. Please do not return this unit to your dealer without first
contacting customer support at the number listed below.
CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to provide
set up help and to answer any question should you encounter problems during your set up
comments or suggestions. For service related issue please contact Elation Professional®.
Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice:
Fax:
(323) 582-3322
(323) 832-9142
E-mail:
Forum:
Warning! To prevent the risk of fire and reduce the risk electrical shock do not attempt to
operate this fixture with the lens cover removed.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
©Elation Professional, Los Angeles Ca.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
yourself. Doing so will void your manufactures warranty.
Please do not discard the shipping carton in the trash. Please recycle whenever possible.
WARRANTY REGISTRATION: The Design LED 72MKII™ carries a two year (730 days)
limited warranty. Please fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be clearly written
on the outside of the return package. A brief description of the problem as well as the R.A.
number must also be written down on a piece of paper and included in the shipping
container. If the unit is under warranty, you must provide a copy of your proof of purchase
invoice. Items returned without a R.A. number clearly marked on the outside of the package
will be refused and returned at customer’s expense. You may obtain a R.A. number by
contacting customer support at (323) 582-3322.
©Elation Professional, Los Angeles Ca.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
2. SAFETY INSTRUCTIONS
To guarantee proper and consistent operation, it is important to
follow the guidelines in this manual. Elation Professional will not
accept responsibility for damages resulting from the misuse of
this fixture due to the disregard of the information printed in this
manual.
1. This fixture has been specially designed for use outdoors. Altering or tampering
with the fixture housing in any way will neglect the IP rating and subsequently
release Elation Professional from any liability resulting from misuse of this
fixture.
2. Allow about 6” (15cm) between this fixture and other devices or a wall to allow
for proper cooling. See page 8.
3. Never touch the fixture during normal operation.
4. Never look directly into the light source. You risk injury to your retina, which may
induce blindness.
5. For safe operation, follow the Installation guide described in chapter six of this
manual. Operating the Design LED 72MKII™ without suited safety aids such as
safety cables or clamps can increase the risk of damage and/or personal injury.
6. Qualified and certified personnel should only perform installation.
7. When mounting this fixture, use only the original rigging points included with this
fixture. Any structural modification will void the original manufactures warranty
and may increase the risk of damage and/or personal injury.
8. Do not attempt to operate this fixture if the power cord has become damaged or
frayed.
9. Never open this fixture while in use.
10.This device falls under protection-class I. Therefore it is essential that the device
be grounded properly.
11.Qualified personnel should perform all electrical connections.
©Elation Professional, Los Angeles Ca.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
12.Be sure the power cord is never crimped or damaged. If the power cord is
damaged, replace it immediately with a new one of similar power rating.
13.Always disconnect from main power before performing any type of service or
any cleaning procedure.
14.Only handle the power cord by the plug. Never pull out the plug by tugging the
wire portion of the cord.
15.Please be aware that damages caused by modifications to the device are
not subject to warranty.
Important Notice: Damages resulting from the disregard of safety and general user
instructions found in this user manual are not subject to any warranty claims.
©Elation Professional, Los Angeles Ca.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
3. FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Low power consumption
Minimal heat emission
Maintenance free operation
Equipped with 72 Luxeon K2 3-Watt (24 x red, 24 x green, 24 x blue)
IP65 Rated for outdoor wet conditions
Silent Operation, convection cooled, no fans
100,000 hours rated LED life
Linear RGB Color Mixing, infinite color possibilities
53˚ Standard Beam Angle
USITT DMX-512 Complaint
Preprogrammed colored macros
Strobe-effect with a maximum flash rate of 18fps
DMX-controlled operation or stand-alone operation with Master/Slave-function
8 built-in programs can be called up via DMX-controller
~ 48 preprogrammed scenes per program
Sound-controlled via built-in microphone
Four DMX Modes:
•
•
15 DMX channels
6 DMX channels
4 DMX channels
3 DMX channels
•
•
•
•
•
•
DMX-control via standard DMX-controller
IP65 rated Connectors for power and DMX
Switching Electronic Power Supply 100v~240v
Flicker-free operation for television and film
Compact case design
0%~100% Dimming (two dimming options; linear & standard)
©Elation Professional, Los Angeles Ca.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
4. GENERAL GUIDELINES
This fixture is a professional lighting effect designed for outdoor architectural installations.
Do not attempt operation or installation without a proper knowledge on how to do so.
Consistent operational breaks will ensure that the fixture will function properly for many
years to come.
Do not shake the fixture around. Avoid brute force when installing or operating the fixture.
While choosing an installation location, please be sure that the fixture will not be exposed to
extreme heat. The minimum distance between the fixture and a wall or flat surface should be
at least 0.5 meter (about 1.5ft). See page 11.
Always install the fixture with an appropriately rated safety cable. When installing the fixture
in a suspended environment always be sure to use mounting hardware no less than M10 x
25 mm, also be sure the hardware is only inserted in the yoke’s mounting holes.
Do not attempt to operate this fixture until you have familiarized yourself with all of its
functions.
Do not permit operation by persons not qualified for operating this type of architectural
fixture. Most damages are the result of improper operation.
Please use the original packaging to transport the fixture in for service.
For your own safety, please read this user manual carefully before installing the device.
©Elation Professional, Los Angeles Ca.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
5. FIXTURE OVERVIEW
©Elation Professional, Los Angeles Ca.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
1. Yoke Assembly – This yoke is designed to perform two functions; 1) When split it
can be used as a floor stand bracket. 2) Used to secure a mounting clamp for truss
mounting.
2. LED Lens Assembly – The lens assembly may be user replaced in the event repair
is needed or a different beam angle is required.
3. DMX In Lead – This lead is the main DMX input lead. When the unit is the first in a
chain or the only fixture to be used with a DMX controller, be sure to use the DMX
starter cable that converts a standard 3-pin XLR DMX connector to the IP rated twist
lock connector that is used on the fixture. When jumping from fixture to fixture be
sure to only use Elation IP rated DMX cables to maintain the IP rating.
4. DMX Out Lead – This lead is used to send an incoming DMX signal to the next
fixture in the DMX chain. To maintain the integrity of the IP rating, only use proper
Elation IP rated DMX cables.
5. Menu Button – This button is used to access the fixtures menu functions.
6. Up Button – The up button is used to toggle forward through the menu functions and
settings.
7. LED Display – 4-segment menu display. Used to display the DMX address as well
as all other menu functions.
8. Down Button – The down button is used to toggle backwards through the menu
functions and settings.
9. Enter Button – The enter button is used to enter in to a certain menu function or to
lock a menu setting in to memory.
©Elation Professional, Los Angeles Ca.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
10. Power Output Lead – This lead is used to jump power to another Design LED
72MKII™. Please do not daisy-chain power for more than 16 fixtures. To maintain
the integrity of the IP rating, only use proper Elation IP rated power cables.
11. Main Power Input Lead – This lead is the main power input lead. When the unit is
the first in a chain or the only fixture to be used, be sure to use the power starter
cable that converts a standard Edison 3-prong to the IP rated twist lock connector.
When jumping from fixture to fixture be sure to only use Elation IP rated power
connectors to maintain the IP rating.
©Elation Professional, Los Angeles Ca.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
6. MOUNTING AND INSTALLATION
Cautions:
For added protection mount the fixtures in areas outside walking paths, seating areas, and
away from areas were unauthorized personnel might reach the fixture.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
To avoid injury, never stand directly below the device when mounting, removing, or servicing
the fixture.
Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE0711-217
for proper installation in Europe To ensure proper installation, only
qualified staff should attempt installation.
Mounting points
Overhead mounting requires extensive experience, including amongst others calculating
working load limits, a fine knowledge of the installation material being used, and periodic
safety inspection of all installation material and the fixture. If you lack these qualifications, do
not attempt the installation yourself. Improper installation can result in bodily injury.
CAUTION!
Be sure a qualified electrician performs all electrical
connections.
Be sure to complete all rigging and installation procedures before connecting the main
power cord to the appropriate wall outlet.
©Elation Professional, Los Angeles Ca.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
Mounting
The Design LED 72MKII™ is fully operational in any mounting position, hanging
upside-down, side mounted, or set on a flat level surface, etc. Be sure this fixture is kept at
least 0.5m (1.5 feet) away from any flammable materials (decoration etc.). When clamp
mounting; always use and install the supplied safety cable as an added safety measure to
prevent accidental damage in the event of a clamp failure. See the image below.
Clamp Mounting
The Design LED 72MKII™ provides a unique mounting bracket assembly that allows the unit
to stand on a flat surface or to be hung on truss via a clamp in any safe position (see the
illustration above). Regardless of the mounting option you choose please be sure to refer to
the safety guidelines in this manual to avoid damage to the unit and/or personal injury.
©Elation Professional, Los Angeles Ca.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
When mounting this fixture to truss be sure to secure an appropriately rated clamp to the
hanging yoke using a M10 screw fitted through the center hole of the hanging yoke. As an
added safety measure be sure to attach at least one properly rated safety cable to the fixture.
See illustrations below.
Securing the Design LED 72MKII™
Always be sure to secure your fixture with a safety cable when
suspending the unit from truss or other means. The fixture
provides a built-in rigging point for a safety cable as illustrated
above. Be sure to only use the designated rigging point for the
safety cable and never secure a safety cable to the hanging
bracket.
©Elation Professional, Los Angeles Ca.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
7. UNDERSTANDING DMX
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most
lighting and controller manufactures as a form of communication between intelligent fixtures
and controllers. DMX allows all makes and models of different manufactures to be linked
together and operate from a single controller. This is possible as long as all the fixtures and
the controller are DMX compliant. A DMX controller sends the DMX data instructions to a
fixture allowing the user to control the different aspects of an intelligent light. DMX data is
sent out as serial data that travels from fixture to fixture via data “IN” and “OUT” leads
located on the fixtures (most controllers will only have output jacks).
DMX Linking: To ensure proper DMX data transmission, always use proper DMX cables
and a terminator. When using several DMX fixtures try to use the shortest cable path
possible. Never split a DMX line with a “Y” style connector. The order in which the fixtures
are connected in a DMX line does not influence the DMX addressing. For example; a fixture
assigned a DMX address of 1 may be placed anywhere in the DMX chain, at the beginning,
at the end, or anywhere in the middle. The DMX controller knows to send data assigned to
address 1 to that fixture no matter where it is located in the DMX chain. The Design LED
72MKII™ can be controlled via DMX-512 protocol. The Design LED 72MKII™ is a fixture
that can operate in 3, 4, 6, or 15 DMX channels (see page 21 for the different DMX traits).
The DMX address is set electronically using the controls on the LED menu.
Cable Requirements: This fixture is designed with special cables for both DMX and power.
These cables are specifically designed to maintain the integrity of the IP rating. When using
this fixture outdoors be sure to ONLY use the Elation cables that have been manufactured to
meet the IP rating.
“First” DMX Cables - Special DMX “First” cables may be purchased from Elation to provide
a means of data communication with standard DMX fixtures for indoor use. These cables will
come with the IP rated twist lock connector on one end and either a 3-pin XLR male or
female connector on the other depending on model. Be sure to only use these cables for
intergrading this fixture in a standard DMX chain.
©Elation Professional, Los Angeles Ca.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
“First” Power Cable – A special power “First” cable is included with every fixture. This
cables is used to provide power to your fixture. This cable comes with the IP rated twist lock
connector on one end and a standard Edison 3-prong, grounded prong on the other end. Be
sure to only use this cable for power distribution and never attempt to connect this cable to
the DMX lines.
You can chain multiple fixtures together through serial linking. Using the IP rated signal
cables provided through Elation. Always be sure to daisy-chain your in and out data
connections, never split or “Y” your DMX connections unless you are using an approved
DMX splitter such as the Elation Opto Branch 4™ or DMX Branch/4™.
DMX-512 connection with DMX terminator
A DMX terminator should be used in all DMX lines especially in longer runs. The use of a
terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt
resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA
-). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain
to terminate the line. Using a line terminator (Elation part: DMX T PACK) will decrease the
possibilities of erratic behavior.
©Elation Professional, Los Angeles Ca.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA
transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX
line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must
be used, these adaptors are readily available at most electric stores. The following chart
details a proper cable conversion.
Fixture DMX addressing;
All fixtures should be given a DMX starting address when using a DMX controller, so the
correct fixture responds to the correct control signal. This digital starting address is the
channel number from which the fixture starts to “listen” to the digital control information sent
out from the DMX controller. The allocation of this starting DMX address is achieved by
setting the correct DMX address on the digital display located on the back of the fixture.
You can set the same starting address for all fixtures or a group of fixtures, or set different
address for each individual fixture. Be advised that setting all you fixtures to the same DMX
address will subsequently control all fixtures in the same fashion, in other words, changing
the settings of one channel will affect all the fixtures simultaneously.
If you set each fixture to a different DMX address, each unit will start to “listen” to the
channel number you have set, based on the quantity of control channels (DMX channels) of
each fixture. That means changing the settings of one channel will only affect the selected
fixture.
©Elation Professional, Los Angeles Ca.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
In the case of the Design LED 72MKII™, which is capable of controlling up to 15 DMX
channels, you should set the starting DMX address of the first unit to 1, the second unit to 16
(15 + 1), the third unit to 31 (15 + 16), and so on.
Note: During start-up the Design LED 72MKII™ will automatically detect whether a DMX
data signal is being received or not. If a DMX data signal is being received, the display will
show "A.XXX" (XXX representing the actual DMX address). If the fixture is not receiving a
DMX signal the display will flash "A.XXX" (XXX representing the actual DMX address).
If your fixture is connected to a DMX controller and the display is flashing (not receiving a
DMX signal), please check the following:
-
The 3-pin or 5-pin XLR plug (cable with DMX signal from controller) may not be
connected or is not inserted completely into the DMX input jack.
The DMX IP cable adapter is fitted incorrectly.
-
-
-
-
The DMX controller is switched off or defective.
The DMX cable or connector is defective.
A DMX terminator has been inserted into the last fixture in your DMX chain.
©Elation Professional, Los Angeles Ca.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
8. DISPLAY LED INDICATORS.
The Design LED 72MKII ™ has two LED indicators on the display. These indicators are
designed to give a quick visual indication of the fixtures’ status. The illustration below details
the functionality of the LED indicators.
. .
.
.
DMX OK
NO DMX
DMX OK
Lamp off
NO DMX
Lamp off
Lamp on
Lamp on
The first LED indicators represents DMX signal:
• If the indicators is on a clean DMX signal is present
• If the indicator is off there is no DMX signal present
The second LED indicator represents lamp condition; this is only applicable to fixtures with
traditional lamp sources.
©Elation Professional, Los Angeles Ca.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
9. MENU
Default settings shaded.
<DMX ADDRESS>
DMX CHANNEL: 1-512
3 CHANNEL MODE
4 CHANNEL MODE
6 CHANNEL MODE
15 CHANNEL MODE
ON/OFF
SET DMX ADDRESS
3 DMX CHANNELS (RGB)
4 DMX CHANNELS (RGB+MASTER DIM)
6 DMX CHANNELS
15 DMX CHANNELS
<DMX OPERATION MODE>
<SET AS SLAVE>
UNIT FUNCTIONS AS SLAVE
UNIT FUNCTIONS AS MASTER
UNIT FUNCTIONS IN STAND ALONE
MASTER
<MANUAL OPERATION MODE>
STAND ALONE
<BLACK OUT>
PRESET VALUE: XXX
RED VALUE
GREEN VALUE
BLUE VALUE
STROBE
SPEED
SET RED VALUE
NEW VALUE: 0-255
PRESET VALUE: XXX
SET GREEN VALUE
NEW VALUE: 0-255
<SET STATIC COLOR>
PRESET VALUE: XXX
SET BLUE VALUE
NEW VALUE: 0-255
PRESET VALUE: XXX
SET STROBE VALUE
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
CHASE 1
CHASE 2
CHASE 3
CHASE 4
FADE
STROBE
SPEED
FADE
STROBE
SPEED
FADE
STROBE
SPEED
FADE
STROBE
SPEED
CHASE 5
CHASE 6
FADE
STROBE
SPEED
FADE
©Elation Professional, Los Angeles Ca.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
STROBE
SPEED
NEW VALUE: 0-256
PRESET VALUE: XXX
NEW VALUE: 0-256
PRESET VALUE: XXX
NEW VALUE: 0-256
PRESET VALUE: XXX
NEW VALUE: 0-256
PRESET VALUE: XXX
NEW VALUE: 0-256
PRESET VALUE: XXX
NEW VALUE: 0-256
EDIT SCENE # XX
FADE
CHASE 7
STROBE
SPEED
FADE
CHASE 8
STROBE
SET CHANNEL
EDIT CHANNEL # XX
VALUE
PROGRAM SCENE BY
ON-BOARD CONTROLS
DOWNLOAD SCENE
FROM CONTROLLER
START SCENE LOOP
(ENTER)
XXX
<EDIT SCENES>
SELECT SCENE # XX
SAVE (ENTER)
SCENE LOOP PLAYS FROM FIRST TO LAST
SCENES
PREVIOUS SCENE #
XXX
SET START SCENE
SET FIRST SCENE FOR SCENE LOOP
NEW SCENE # XXX
PREVIOUS SCENE #
XXX
SET END SCENE
SPEED
SET LAST SCENE FOR SCENE LOOP
SET SCENE LOOP SPEED
<PLAY SCENES>
<DIMMER MODE>
NEW SCENE # XXX
PRESET VALUE: XXX
NEW VALUE: 0-255
PRESET VALUE: XXX
NEW VALUE: 0-255
FADE
SET SCENE LOOP FADE
MODE 1 (ENTER)
MODE 2 (ENTER)
YES (ENTER)
STANDARD DIMMING OPTION
LINEAR DIMMING OPTION
<FACTORY RESET>
RESTORE FACTORY DEFAULT SETTINGS
<SOFTWARE VERSION>
V X.X
DISPLAY'S CURRENT SOFTWARE VERSION
NOTICE:
1) If the fixture does not receive a DMX signal the menu display will flash repeatedly.
2) The “SPED” and “FADE” function only work when the fixture is operating via one of the
internal chase programs.
3) SPED: Adjust the hold time for each scene in built-in chase programs.
4) FADE: Adjust the fade time between each scene in the built-in programs.
5) This fixture will automatically retain the last DMX command in the event of DMX failure.
©Elation Professional, Los Angeles Ca.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
10.DMX TRAITS
DMX Operation Notes:
The fixture will function in DMX mode whenever the unit is receiving a DMX signal. Please
note that this will override all manual settings.
This unit will keep and retain the last DMX command in the event of DMX signal failure. To
reset the fixture you must turn the power off.
DMX CHANNEL TRAITS
The charts below and on the preceding pages outline the different DMX traits for the three
different DMX modes.
3-Channel mode: In this mode channel one controls all the red LEDs, channel two controls
all the green LEDs, and channels three controls all the blue LEDs.
CHANNEL 1:Red
CHANNEL 2:Green
CHANNEL 3:Blue
3-Channel Mode: The chart below details the DMX channel layout for 3-channel assignment.
DMX channel’s functions and their values (3-Channel Mode):
Channel 1 - Red:
0-255
Red (0-Black, 255 - 100% Red)
Channel 2 - Green:
0-255
Green (0-Black, 255 - 100% Green)
Channel 3 - Blue:
0-255
Blue (0-Black, 255 - 100% Blue)
©Elation Professional, Los Angeles Ca.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
4-Channel mode: In this mode channel one controls all the red LEDs, channel two controls
all the green LEDs, channels three controls all the blue LEDs, and channel four-- will control
the master dimming level.
CHANNEL 1:Red
CHANNEL 2:Green
CHANNEL 3:Blue
CHANNEL 4:Dimmer/Speed
4-Channel Mode: The chart below details the DMX channel layout for 4-channel assignment.
DMX channel’s functions and their values (4-Channel Mode):
Channel 1 - Red:
0-255
Red (0-Black, 255 - 100% Red)
Channel 2 - Green:
0-255
Green (0-Black, 255 - 100% Green)
Channel 3 - Blue:
0-255
Blue (0-Black, 255 - 100% Blue)
Channel 4 - Dimming / Program Speed Control
This channel has two functions depending on the operating mode. When running the built-in
programs this channel will control the program speed.
0-255
0-255
Dimming (0%-100%) ~ Normal Operation
Speed (min to max) ~ When running built-in programs on channel 4
©Elation Professional, Los Angeles Ca.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
6-Channel mode: In this mode channels 1~3 are used to control the RGB LEDs and
channels 4~6 will control special features.
CHANNEL 1:Red
CHANNEL 2:Green
CHANNEL 3:Blue
CHANNEL 4:Auto Programs (Built-in Programs)
CHANNEL 5:Strobe
CHANNEL 6:Dimmer/Speed
6-Channel Mode: The charts below and on the next page detail the DMX channel layout for
6-channel assignment.
DMX channel’s functions and their values (6-Channel Mode):
Channel 1 - Red:
0-255
Red (0-Black, 255-100% Red)
©Elation Professional, Los Angeles Ca.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
Channel 2 - Green:
0-255
Green (0-Black, 255- 100% Green)
Channel 3 - Blue:
0-255
Blue (0-Black, 255- 100% Blue)
Channel 4 - Internal programs:
0-10
No function
11-40
Internal program 1
Internal program 2
Internal program 3
Internal program 4
Internal program 5
Internal program 6
Internal program 7
Internal program 8
41-70
71-100
101-130
131-160
161-190
191-220
221-255
Channel 5 - Strobe:
0
No function
1~95
Strobe effect slow to fast
No function
96-127
128-159
160-191
192-223
224-255
Pulse effect in sequences
No function
Random strobe effect slow to fast
No function
Channel 6 - General dimming / Program Speed Control
This channel has two functions depending on the operating mode. When running the built-in
programs this channel will control the program speed, when not running the built-in programs
this channel will control master dimming.
0-255
0-255
Dimming (0%-100%) ~ Normal Operation
Speed (min to max) ~ When running built-in programs on channel 4
©Elation Professional, Los Angeles Ca.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
15-Channel mode: In this mode channels 1~12 are used to control the RGB LEDs and
channels 13~15 will control special features.
CHANNEL 1:Red
CHANNEL 2:Green
CHANNEL 3:Blue
CHANNEL 4:Red
CHANNEL 5:Green
CHANNEL 6:Blue
CHANNEL 7:Red
CHANNEL 8:Green
CHANNEL 9:Blue
CHANNEL 10:Red
CHANNEL 11:Green
CHANNEL 12:Blue
CHANNEL 13:Auto Programs (Built-in Programs)
CHANNEL 14:Strobe
CHANNEL 15:Dimmer/Speed
15-Channel Mode: The charts below and on the next page detail the DMX channel layout for
15-channel assignment.
CH14 CH15
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13
Reset
Dimming
Strobe
and
R
G
B
R
G
B
R
G
B
R
G
B
program
speed
DMX channel’s functions and their values (6-Channel Mode):
Channel 1 - Red:
0-255
Channel 2 - Green:
0-255 Green (0-Black, 255- 100% Green)
Red (0-Black, 255-100% Red)
©Elation Professional, Los Angeles Ca.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
Channel 3 - Blue:
0-255
Blue (0-Black, 255- 100% Blue)
Channel 4 - Red:
0-255
Red (0-Black, 255-100% Red)
Channel 5 - Green:
0-255
Green (0-Black, 255- 100% Green)
Channel 6 - Blue:
0-255
Blue (0-Black, 255- 100% Blue)
Channel 7 - Red:
0-255
Red (0-Black, 255-100% Red)
Channel 8 - Green:
0-255
Green (0-Black, 255- 100% Green)
Channel 9 - Blue:
0-255
Blue (0-Black, 255- 100% Blue)
Channel 10 - Red:
0-255
Red (0-Black, 255-100% Red)
Channel 11 - Green:
0-255
Green (0-Black, 255- 100% Green)
Channel 12 - Blue:
0-255
Blue (0-Black, 255- 100% Blue)
Channel 13 - Internal programs:
0-10
No function
11-40
41-70
71-100
Internal program 1
Internal program 2
Internal program 3
©Elation Professional, Los Angeles Ca.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
101-130
131-160
161-190
191-220
221-255
Internal program 4
Internal program 5
Internal program 6
Internal program 7
Internal program 8
Channel 14 - Strobe:
0
No function
1~95
Strobe effect slow to fast
No function
96-127
128-159
160-191
192-223
224-255
Pulse effect in sequences
No function
Random strobe effect slow to fast
No function
Channel 15 - General dimming / Program Speed Control
This channel has two functions depending on the operating mode. When running the built-in
programs this channel will control the program speed, when not running the built-in programs
this channel will control master dimming.
0-255
0-255
Dimming (0%-100%) ~ Normal Operation
Speed (min to max) ~ When running built-in programs on channel 13
©Elation Professional, Los Angeles Ca.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
11. CLEANING AND MAINTENANCE
Consider the following points during normal service and inspection:
1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may
fall out during normal operation resulting in damage or injury as larger parts could fall.
2. Electric power supply cables must not show any damage, material fatigue or
sediments. Never remove the ground prong from the power cable.
Further instructions depending on the installation spot and usage have to be adhered by a
skilled installer and any safety problems have to be removed.
Disconnect from mains before starting maintenance operation.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never
use alcohol or solvents.
There are no user serviceable parts inside this fixture, please refer all other service issues to
an authorized Elation service technician.
Should you need any spare parts, please order genuine parts from your local dealer.
©Elation Professional, Los Angeles Ca.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
12.
2-YEAR LIMITED WARRANTY
A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional®
products to be free of manufacturing defects in material and workmanship for a period of two
years, (730 days) from the date of purchase. This warranty shall be valid only if the product
is purchased within the United States of America, including possessions and territories. It is
the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service, send the product only to the Elation Professional® factory. All
shipping charges must be pre-paid. If the requested repairs or service (including parts
replacement) are within the terms of this warranty, Elation Professional® will pay return
shipping charges only to a designated point within the United States. If the entire instrument
is sent, it must be shipped in its original package. No accessories should be shipped with the
product. If any accessories are shipped with the product, Elation Professional® shall have no
liability what so ever for loss of or damage to any such accessories, nor for the safe return
thereof.
C.
This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which Elation Professional® concludes, after inspection, affects the
reliability of the product; if the product has been repaired or serviced by anyone other than
the Elation Professional® factory unless prior written authorization was issued to purchaser
by Elation Professional®; if the product is damaged because not properly maintained as set
forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, Elation Professional® will replace
defective parts at its expense, and will absorb all expenses for warranty service and repair
labor by reason of defects in material or workmanship. The sole responsibility of Elation
Professional® under this warranty shall be limited to the repair of the product, or replacement
thereof, including parts, at the sole discretion of Elation Professional®. All products covered
by this warranty were manufactured after January 1, 1990, and bare identifying marks to that
©Elation Professional, Los Angeles Ca.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
effect.
E. Elation Professional® reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products
theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by
applicable law, all implied warranties made by Elation Professional® in connection with this
product, including warranties of merchantability or fitness, are limited in duration to the
warranty period set forth above. And no warranties, whether expressed or implied, including
warranties of merchantability or fitness, shall apply to this product after said period has
expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as
is expressly provided above; and under no circumstances shall Elation Professional® be
liable for any loss or damage, direct or consequential, arising out of the use of, or inability to
use, this product.
G. This warranty is the only written warranty applicable to Elation Professional® Products
and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
©Elation Professional, Los Angeles Ca.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
13.
PHOTOMETRIC DATA
©Elation Professional, Los Angeles Ca.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
14.
DIMENSIONAL DRAWINGS
©Elation Professional, Los Angeles Ca.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
15.
CIRCUIT SCHEMATIC
©Elation Professional, Los Angeles Ca.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN LED 72MKII™
16.
TECHNICAL SPECIFICATIONS
Power supply:
100v~240v / 50Hz~60Hz AC
Maximum 150w
Power consumption:
LED Configuration:
72 Luxeon K2, 3 Watts Each
(24 x Red, 24 x Green 24 x Blue)
IP65
IP Rating:
Weight:
12 Kgs
DMX Channels:
DMX Drive:
15, 6, 4, or 3 Channel mode
Standard DMX-512,
3 pole IP Rated Locking Connector; [+] = Pin 3 [-] = Pin 2
[Ground] = Pin 1.
Color Mixing:
Beam Angle:
Fuse:
RGB Color Additive Mixing
53˚
GMA 220v~4A (Internal)
Dimmer:
Continuous Dimming 0~100%
Electronic Strobe 0~18 Fps
100,000 Hours Rated Life
(377 x 341 x 198) mm, bracket up
Strobe:
LED Life:
Dimensions:
Please Note: Specifications and improvements in the design of this unit and this manual are
subject to change without any prior written notice.
©Elation Professional, Los Angeles Ca.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Elation Professional
6122 S. Eastern Ave.
Los Angeles, CA. 90040
323-582-3322 / 323-832-9142 fax
Rev. 09/15/2008 - visage
Download from Www.Somanuals.com. All Manuals Search And Download.
|