FEATURES
ꢀ
High efficiency: 92.0% @3.3V/30A
ꢀ
Size: 58.4mm x 22.8mm x9.5mm
(2.30”x0.90”x0.37”)
ꢀ
ꢀ
ꢀ
ꢀ
Industry standard pin out
Fixed frequency operation
Input UVLO, Output OTP, OCP, OVP
Monotonic startup into normal and
pre-biased loads
ꢀ
Secondary control, very fast transient
response
ꢀ
ꢀ
ꢀ
2250V Isolation and basic insulation
No minimum load required
No negative current during power or enable
on/off
ꢀ
ꢀ
ꢀ
ISO 9001, TL 9000, ISO 14001, QS 9000,
OHSAS 18001 certified manufacturing facility
UL/cUL 60950 (US & Canada) recognized,
and TUV (EN60950) certified
CE mark meets 73/23/EEC and 93/68/EEC
directive
Delphi Series E48SH, 120W Eighth Brick Family
DC/DC Power Modules: 48V in, 3.3V/30A out
The Delphi Series E48SH Eighth Brick, 48V input, single output, isolated
DC/DC converters are the latest offering from a world leader in power
systems technology and manufacturing ― Delta Electronics, Inc. This
product family is available in either a through-hole or surface-mounted
package and provides up to 120 watts of power or 50A of output current
(1.2V and below) in an industry standard footprint and pinout. The E48SH
converter operates from an input voltage of 36V to 75V and is available in
output voltages from 1.0V to 15V. Efficiency is up to 92.0% for 3.3V
output at 30A full load. With creative design technology and optimization
of component placement, these converters possess outstanding
electrical and thermal performance, as well as extremely high reliability
under highly stressful operating conditions. All models are fully protected
from abnormal input/output voltage, current, and temperature conditions.
The Delphi Series converters meet all safety requirements with basic
insulation.
OPTIONS
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Positive On/Off logic
Short pin lengths available
External Synchronization
Output OVP latch mode
Output OCP latch mode
Heat spreader
APPLICATIONS
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Telecom/DataCom
Wireless Networks
Optical Network Equipment
Server and Data Storage
Industrial/Test Equipment
DATASHEET
DS_E48SH3R330_02162007
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CHARACTERISTICS CURVES
Figure 1: Efficiency vs. load current for minimum, nominal, and
maximum input voltage at 25°C
Figure 2: Power dissipation vs. load current for minimum,
nominal, and maximum input voltage at 25°C.
4
3.5
3
2.5
2
1.5
1
0.5
0
30
38
46
54
62
70
78
INPUT VOLTAGE(V)
Figure 3: Typical full load input characteristics at room
temperature
E48SH3R330_02162007
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CHARACTERISTICS CURVES
For Negative Remote On/Off Logic
Figure 4: Turn-on transient at zero load current (5 ms/div).
Vin=48V.Top Trace: Vout, 2V/div; Bottom Trace: ON/OFF input,
2V/div
Figure 5: Turn-on transient at full rated load current (constant
current load) (5 ms/div). Vin=48V.Top Trace: Vout, 2V/div;
Bottom Trace: ON/OFF input, 2V/div
For Input Voltage Start up
Figure 6: Turn-on transient at zero load current (5 ms/div).
Vin=48V.Top Trace: Vout, 2V/div, Bottom Trace: input voltage,
50V/div
Figure 7: Turn-on transient at full rated load current (constant
current load) (5 ms/div). Vin=48V.Top Trace: Vout, 2V/div;
Bottom Trace: input voltage, 50V/div
E48SH3R330_02162007
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CHARACTERISTICS CURVES
Figure 8: Output voltage response to step-change in load
current (75%-50% of Io, max; di/dt = 0.1A/µs). Load cap: 10µF,
tantalum capacitor and 1µF ceramic capacitor. Trace: Vout
(50mV/div, 100us/div), Scope measurement should be made
using a BNC cable (length shorter than 20 inches). Position the
load between 51 mm to 76 mm (2 inches to 3 inches) from the
module..
Figure 9: Output voltage response to step-change in load
current (50%-75% of Io, max; di/dt = 0.1A/µs). Load cap: 10µF,
tantalum capacitor and 1µF ceramic capacitor. Trace: Vout
(50mV/div, 100us/div), Scope measurement should be made
using a BNC cable (length shorter than 20 inches). Position the
load between 51 mm to 76 mm (2 inches to 3 inches) from the
module..
Figure 10: Test set-up diagram showing measurement points
for Input Terminal Ripple Current and Input Reflected Ripple
Current.
Figure 11: Input Terminal Ripple Current, ic, at full rated output
current and nominal input voltage with 12µH source impedance
and 33µF electrolytic capacitor (200 mA/div, 2us/div).
Note: Measured input reflected-ripple current with a simulated
source Inductance (LTEST) of 12 µH. Capacitor Cs offset
possible battery impedance. Measure current as shown above
E48SH3R330_02162007
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CHARACTERISTICS CURVES
Copper Strip
Vo(+)
Vo(-)
SCOPE
RESISTIVE
LOAD
10u
1u
Figure 12: Input reflected ripple current, is, through a 12µH
source inductor at nominal input voltage and rated load current
(20 mA/div, 2us/div).
Figure 13: Output voltage noise and ripple measurement test
setup
Figure 14: Output voltage ripple at nominal input voltage and
rated load current (Io=30A)(50 mV/div, 2us/div)
Figure 15: Output voltage vs. load current showing typical
current limit curves and converter shutdown points.
Load capacitance: 1µF ceramic capacitor and 10µF tantalum
capacitor. Bandwidth: 20 MHz. Scope measurements should be
made using a BNC cable (length shorter than 20 inches).
Position the load between 51 mm to 76 mm (2 inches to 3
inches) from the module.
E48SH3R330_02162007
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN CONSIDERATIONS
ꢀ
ꢀ
ꢀ
The input source must be insulated from the ac
mains by reinforced or double insulation.
Input Source Impedance
The impedance of the input source connecting to the
DC/DC power modules will interact with the modules and
affect the stability. A low ac-impedance input source is
recommended. If the source inductance is more than a
few µH, we advise adding a 10µF to 100µF electrolytic
capacitor (ESR < 0.7 Ω at 100 kHz) mounted close to the
input of the module to improve the stability.
The input terminals of the module are not operator
accessible.
If the metal baseplate is grounded, one Vi pin and
one Vo pin shall also be grounded.
ꢀ
A SELV reliability test is conducted on the system
where the module is used, in combination with the
module, to ensure that under a single fault,
hazardous voltage does not appear at the module’s
output.
Layout and EMC Considerations
Delta’s DC/DC power modules are designed to operate
in a wide variety of systems and applications. For design
assistance with EMC compliance and related PWB
layout issues, please contact Delta’s technical support
team. An external input filter module is available for
easier EMC compliance design. Application notes to
assist designers in addressing these issues are pending
release.
When installed into a Class II equipment (without
grounding), spacing consideration should be given to
the end-use installation, as the spacing between the
module and mounting surface have not been evaluated.
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
Safety Considerations
This power module is not internally fused. To achieve
optimum safety and system protection, an input line fuse
is highly recommended. The safety agencies require a
normal-blow fuse with 10A maximum rating to be
installed in the ungrounded lead. A lower rated fuse can
be used based on the maximum inrush transient energy
and maximum input current.
The power module must be installed in compliance with
the spacing and separation requirements of the
end-user’s safety agency standard, i.e., UL60950,
CAN/CSA-C22.2 No. 60950-00 and EN60950: 2000 and
IEC60950-1999, if the system in which the power module
is to be used must meet safety agency requirements.
Basic insulation based on 75 Vdc input is provided
between the input and output of the module for the
purpose of applying insulation requirements when the
input to this DC-to-DC converter is identified as TNV-2 or
SELV. An additional evaluation is needed if the source
is other than TNV-2 or SELV.
Soldering and Cleaning Considerations
Post solder cleaning is usually the final board assembly
process before the board or system undergoes electrical
testing. Inadequate cleaning and/or drying may lower the
reliability of a power module and severely affect the
finished circuit board assembly test. Adequate cleaning
and/or drying is especially important for un-encapsulated
and/or open frame type power modules. For assistance
on appropriate soldering and cleaning procedures,
please contact Delta’s technical support team.
When the input source is SELV circuit, the power module
meets SELV (safety extra-low voltage) requirements. If
the input source is a hazardous voltage which is greater
than 60 Vdc and less than or equal to 75 Vdc, for the
module’s output to meet SELV requirements, all of the
following must be met:
E48SH3R330_02162007
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES DESCRIPTIONS
Vi(+)
Vo(+)
Over-Current Protection
Sense(+)
The E48SH modules include an internal output
over-current protection circuit, which will endure current
limiting for an unlimited duration during output overload.
When the output current exceeds the OCP set point, the
current limit function will work by initially reduce duty
cycle of the module, the unit will go out of regulation but
remains in safe operating area before the output drops
below 50%. When output drops below 50%, the
modules will automatically shut down and enter hiccup
mode.
ON/OFF
Sense(-)
Vi(-)
Vo(-)
Figure 16: Remote on/off implementation
Remote Sense
During hiccup, the modules will try to restart after
shutdown. If the overload condition still exists, the
module will shut down again. This restart trial will
continue until the overload condition is corrected.
Remote sense compensates for voltage drops on the
output by sensing the actual output voltage at the point
of load. The voltage between the remote sense pins
and the output terminals must not exceed the output
voltage sense range given here:
Over-Voltage Protection
[Vo(+) – Vo(–)] – [SENSE(+) – SENSE(–)] ≤ 10% × Vout
The modules include an internal output over-voltage
protection circuit, which monitors the voltage on the
output terminals. If this voltage exceeds the over-voltage
set point, the module will shut down and restart after
200mS. latch off mode is optional. Under latch off mode
the over-voltage latch is reset by either cycling the input
power or by toggling the on/off signal for one second.
This limit includes any increase in voltage due to
remote sense compensation and output voltage set
point adjustment (trim).
Vi(+) Vo(+)
Sense(+)
Over-Temperature Protection
The over-temperature protection consists of circuitry
that provides protection from thermal damage. If the
temperature exceeds the over-temperature threshold
the module will shut down.
Sense(-)
Vi(-) Vo(-)
Contact
Resistance
Contact and Distribution
Losses
The module will try to restart after shutdown. If the
over-temperature condition still exists during restart, the
module will shut down again. This restart trial will
continue until the temperature is within specification.
Figure 17: Effective circuit configuration for remote sense
operation
If the remote sense feature is not used to regulate the
output at the point of load, please connect SENSE(+) to
Vo(+) and SENSE(–) to Vo(–) at the module.
Remote On/Off
The remote on/off feature on the module can be either
negative or positive logic. Negative logic turns the
module on during a logic low and off during a logic high.
Positive logic turns the modules on during a logic high
and off during a logic low.
The output voltage can be increased by both the
remote sense and the trim; however, the maximum
increase is the larger of either the remote sense or the
trim, not the sum of both.
Remote on/off can be controlled by an external switch
between the on/off terminal and the Vi(-) terminal. The
switch can be an open collector or open drain.
When using remote sense and trim, the output voltage
of the module is usually increased, which increases the
power output of the module with the same output
current.
For negative logic if the remote on/off feature is not
used, please short the on/off pin to Vi(-). For positive
logic if the remote on/off feature is not used, please
leave the on/off pin to floating.
Care should be taken to ensure that the maximum
output power does not exceed the maximum rated
power.
E48SH3R330_02162007
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES DESCRIPTIONS (CON.)
If the external resistor is connected between the TRIM
and SENSE (+) the output voltage set point increases
(Fig. 19). The external resistor value required to obtain
a percentage output voltage change △% is defined
as:
Output Voltage Adjustment (TRIM)
To increase or decrease the output voltage set point,
the modules may be connected with an external
resistor between the TRIM pin and either the
SENSE(+) or SENSE(-). The TRIM pin should be left
open if this feature is not used.
5.11Vo (100 + ∆ ) 511
Rtrim − up =
−
− 10.2(KΩ
)
1.225 ∆
∆
Ex. When Trim-up +10%(3V×1.1=3.3V)
5.11× 3.3× (100 +10 ) 511
Rtrim − up =
−
−10.2 = 90.1 KΩ
(
)
1.225×10
10
The output voltage can be increased by both the remote
sense and the trim, however the maximum increase is
the larger of either the remote sense or the trim, not the
sum of both.
Figure 18: Circuit configuration for trim-down (decrease
output voltage)
When using remote sense and trim, the output voltage
of the module is usually increased, which increases the
power output of the module with the same output
current.
If the external resistor is connected between the TRIM
and SENSE (-) pins, the output voltage set point
decreases (Fig. 18). The external resistor value
required to obtain a percentage of output voltage
change △% is defined as:
Care should be taken to ensure that the maximum
output power of the module remains at or below the
maximum rated power.
511
Rtrim − down =
−10.2(KΩ)
∆
Frequency Synchronization
Ex. When Trim-down -10%(3.3V×0.9=2.97V)
This product family can be synchronized with external clock
signal to the TRIM pin. This reduces system noise and
interference in multiple converter systems.
511
Rtrim − down =
− 10.2 = 40.9(KΩ)
10
Figure 19: Circuit configuration for trim-up (increase output
voltage)
E48SH3R330_02162007
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Thermal Derating
THERMAL CONSIDERATIONS
Heat can be removed by increasing airflow over the
module. The hottest point temperature of the module is
129℃. To enhance system reliability; the power module
should always be operated below the maximum
operating temperature. If the temperature exceeds the
maximum module temperature, reliability of the unit may
be affected.
Thermal management is an important part of the system
design. To ensure proper, reliable operation, sufficient
cooling of the power module is needed over the entire
temperature range of the module. Convection cooling is
usually the dominant mode of heat transfer.
Hence, the choice of equipment to characterize the
thermal performance of the power module is a wind
tunnel.
THERMAL CURVES
Thermal Testing Setup
Delta’s DC/DC power modules are characterized in
heated vertical wind tunnels that simulate the thermal
environments encountered in most electronics
equipment. This type of equipment commonly uses
vertically mounted circuit cards in cabinet racks in which
the power modules are mounted.
The following figure shows the wind tunnel
characterization setup. The power module is mounted
on a test PWB and is vertically positioned within the
wind tunnel. The space between the neighboring PWB
and the top of the power module is constantly kept at
6.35mm (0.25’’).
Figure 21: Case temperature measurement location.
Pin locations are for reference only.
＊
The allowed maximum hot spot temperature is defined at
129℃
E48SH3R330(Standard) Output Current vs. Ambient Temperature and Air Velocity
Output Current(A)
@Vin = 48V (Transverse Orientation)
30
25
20
15
10
5
PWB
MODULE
FACING PWB
Natural
Convection
100LFM
200LFM
300LFM
AIR VELOCITY
400LFM
AND AMBIENT
TEMPERATURE
MEASURED BELOW
THE MODULE
50.8 (2.0”)
AIR FLOW
0
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
12.7 (0.5”)
Figure 22: Output current vs. ambient temperature and air
velocity @ Vin=48V (Transverse Orientation)
Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches)
Figure 20: Wind tunnel test setup
E48SH3R330_02162007
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PICK AND PLACE LOCATION
SURFACE-MOUNT TAPE & REEL
RECOMMENDED PAD LAYOUT (SMD)
E48SH3R330_02162007
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LEADED (Sn/Pb) PROCESS RECOMMEND TEMP. PROFILE
Peak temp.
2nd Ramp-up temp.
210~230°C 5sec.
1.0~3.0°C /sec.
250
Pre-heat temp.
140~180°C 60~120 sec.
200
Cooling down rate <3°C /sec.
Ramp-up temp.
0.5~3.0°C /sec.
150
100
50
Over 200°C
40~50sec.
0
60
120
Time ( sec. )
180
240
300
Note: The temperature refers to the pin of E48SH, measured on the pin +Vout joint.
LEAD FREE (SAC) PROCESS RECOMMEND TEMP. PROFILE
.
Temp
Peak Temp. 240 ~ 245 ℃
217℃
200℃
Ramp down
max. 4℃/sec.
Preheat time
100~140 sec.
150℃
25℃
Time Limited 90 sec.
above 217℃
Ramp up
max. 3℃/sec.
Time
Note: The temperature refers to the pin of E48SH, measured on the pin +Vout joint.
E48SH3R330_02162007
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MECHANICAL DRAWING
SURFACE-MOUNT MODULE
THROUGH-HOLE MODULE
Pin No.
Name
Function
1
2
3
4
5
6
7
8
+Vin
ON/OFF
-Vin
-Vout
-SENSE
TRIM
Positive input voltage
Remote ON/OFF
Negative input voltage
Negative output voltage
Negative remote sense
Output voltage trim
+SENSE
+Vout
Positive remote sense
Positive output voltage
E48SH3R330_02162007
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MECHANICAL DRAWING (WITH HEATSPREADER)
THROUGH-HOLE MODULE
E48SH3R330_02162007
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PART NUMBERING SYSTEM
E
48
S
H
3R3
30
N
R
F
A
Type of
Product
Input
Voltage
Number of Product
Outputs Series
Output
Voltage
Output
Current
30 - 30A
ON/OFF
Logic
N- Negative
Pin Length
Option Code
E- Eighth 48-36V~75V S- Single H-50A series 3R3 - 3.3V
Brick
R- 0.170”
N- 0.145”
K- 0.110”
M- SMD
A- Standard functions
H - With heatspreader
F- RoHS 6/6
(Lead Free)
P- Positive
MODEL LIST
MODEL NAME
E48SH1R250NRFA
E48SH1R540NRFA
E48SH1R840NRFA
E48SH2R535NRFA
E48SH3R330NRFA
E48SH05020NRFA
E48SH12010NRFA
INPUT
OUTPUT
EFF @ 100% LOAD
36V~75V
36V~75V
36V~75V
36V~75V
36V~75V
36V~75V
36V~75V
2.3A
2.2A
2.7A
2.9A
3.6A
3.7A
4.3A
1.2V
1.5V
1.8V
2.5V
3.3V
5.0V
12V
50A
40A
40A
35A
30A
20A
10A
86.5%
89%
90%
89.5%
92%
90%
93.5%
Default remote on/off logic is negative and pin length is 0.170”
For different remote on/off logic and pin length, please refer to part numbering system above or contact your local sales
office.
USA:
Telephone:
East Coast: (888) 335 8201
West Coast: (888) 335 8208
Fax: (978) 656 3964
Email: [email protected]
Europe:
Asia & the rest of world:
Telephone: +886 3 4526107 x 6220
Fax: +886 3 4513485
Telephone: +41 31 998 53 11
Fax: +41 31 998 53 53
Email: [email protected]
Email: [email protected]
WARRANTY
Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available upon
request from Delta.
Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta for
its use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license is
granted by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these
specifications at any time, without notice.
E48SH3R330_02162007
15
Download from Www.Somanuals.com. All Manuals Search And Download.
|