Eclipse Fujitsu Ten Marine Radio CD3431 User Manual

by FUJITSU TEN

MODEL

CD3431

ESN E3 High-Power CD Receiver with

CDC/E-COM/DSP Control and Wireless Remote

OWNER'S MANUAL

We appreciate your purchase of this receiver.

Please read through this manual for correct operation.

We suggest that after reading it you keep this manual

in a safe place for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning

Do not place the vinyl storage bag over a person. It may

cause a serious accident or death by suffocation.

•

Do not adjust the controls while driving the car. To adjust the

controls, stop the car in a safe location.

To prevent accidents, store batteries for the remote control

out of the reach of small children.In case a child swallows a

battery, consult a physician immediately.

Do not disassemble or rebuild this product. Doing so may

cause an accident, fire or electrical shock.

•

When it is necessary to replace the fuse, always use a fuse of

the correct rating (number of amperes). Use of fuses with

higher amperage ratings may cause a fire.

Do not operate the product in a malfunctioning condition, for

instance, when the audio does not play. Doing so may result

in an accident, fire or electrical shock.

•

If an abnormal situation occurs, such as foreign matter

entering or liquid splashing on the product, or smoke or a

strange odor emitting from the unit, shut off the product

immediately and consult the dealer from whom you purchased

it. Continued operation may cause an accident, fire or

electrical shock.

Do not install this product in locations where it may obstruct

the driver's view, or where it may endanger passengers in the

vehicle. Otherwise, an accident or injury may result.

•

Do not install this product in locations where it may interfere

with the operation of the steering wheel, shift lever, brake

pedal, etc. Otherwise, an accident or injury may result.

When installing this product, never use existing nuts or bolts

that secure parts of the fuel tank, or the steering or braking

systems. Otherwise improper steering or braking or a fire may

result.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning

To prevent a short circuit from occurring, disconnect the

battery's negative terminal before installing this product.

Otherwise, an electric shock or injury may result.

•

When using an existing nut and/or bolt from the vehicle to

ground this product, do not use any that secure parts of the

steering or braking systems. Otherwise, an accident may

result.

Bundle cables and harnesses with electrical tape or wire ties

to prevent them from interfering with moving parts. If they

should entangle the steering wheel, shift lever or brake pedal,

an accident may result.

•

Never supply power to another electrical appliance by splicing

or tapping into this product's power lead(wire).Otherwise the

current capacity of the wire will be exceeded, resulting in a fire

or electric shock.

Never attempt to disassemble or modify the product.

Otherwise, an accident, fire or electric shock may result.

•

When installing the product into a vehicle with a passenger

side air bag, do not secure it to the air bag's cover or in places

where it may impede air bag deployment. Otherewise, proper

aie bag operation may not be ensured in the event of an

accident, causing injury or death.

When making holes using a drill or simiar tool, be sure to wear

protestive eyewear. Otherwise, an injury such as loss of

evesight may result.

•

Exposed wires must be insulated with electrical tape.

Othewise, a short circuit, fire, or electric shock may result.

Download from Www.Somanuals.com. All Manuals Search And Download.

Caution

Play the audio at a moderate volume level that permits you to

hear sounds from outside the car. Driving without being able

to hear outside sounds may result in an accident.

•

Keep foreign objects out of the disc slot. They may cause fire

or electrical shock. Another possibility is that discs may be

damaged or become stuck.

Do not stick your fingers or hands into the disc slot. Doing so

may cause personal injury.

•

This product must be operated only as on-board equipment,

or it may cause electrical shock or injury.

Do not play distorted sounds for long periods of time;

the speakers may overheat and cause a fire.

This product uses an invisible laser light. In case a problem

develops, be sure to consult the dealer from whom you

purchased the product. Do not disassemble or rebuild the

unit; rebuilding it may expose you and others to a dangerous

laser emission (which would damage eyesight) or cause an

accident.

Never use batteries other than those specified. Do not mix

new and old cells. Doing so may cause a fire or personal injury

due to a battery explosion or chemical leaks.

•

Pay attention to the (+) and (-) polarity of the battery when

installing it in the product. Incorrect installation may cause

personal injury or product damage due to a battery explosion

or chemical leakage.

For best results, this product should be installed by a

•

professional installer.

Contact the dealer whom you purchased the product for an

appointment.

When installing this product, be sure to use the supplied

mounting hardware. If parts other than those supplied are

used, the unit may be damaged internally, or may not be held

in place securely and become dislodged.

Download from Www.Somanuals.com. All Manuals Search And Download.

Caution

Avoid installing this product in places where it may get wet,

such as near windows, or in places that are moist or dusty.

Presence of liquid, moisture or dust inside this product can

cause short circuiting, resulting in smoke or fire.

•

Do not install this product in locations where it cannot be

fastened securely, such as places subject to frequent

vibretion. Otherwise, it may become dislodged and cause an

accident or injury.

Do not block this product's vent or heat sink. If either is

blocked, excessive heat build-up may occur and cause a fire.

•

If this product is not connected properly, a short circuit, fire or

accident may occur.

When routing cables, use care so that they do not contact

sharp metal parts such as brackets or screw tips. Otherwise,

a short circuit, electric shock, fire or accident may result.

Do not obstruct the vent on this product. If blocked, excessive

heat build-up may occur and cause a fire.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Operating Precautions .............................................. 10

Notes on Operation...................................................................... 10

About compact discs .................................................................. 12

About cleaning a CD ................................................................... 14

Names of controls and parts .................................... 15

ESN (Key CD) Security Operating Procedure .......... 16

How to program the Key CD ....................................................... 16

How to cancel the Key CD .......................................................... 17

How to change the Key CD ......................................................... 18

How to resume normal operation (ESN security lock out) ............ 19

What happens if an incorrect CD is inserted? .............................. 20

How to turn the Security indicator on/off .......................................21

How to Read the Electrical Serial Number ................................... 21

Basic operation ......................................................... 22

Turning the power on and off ...................................................... 22

Listening to a CD ......................................................................... 22

Listening to the tuner ................................................................... 23

Adjusting audio volume ............................................................... 24

Displaying the clock ..................................................................... 24

Others ......................................................................................... 25

How to operate the CD player .................................. 29

Listening to CDs .......................................................................... 29

Advancing to the next track or returning to

the beginning of the track being played ....................................... 30

Playing the beginning of tracks (SCAN) ........................................ 30

Repeating the same track (REPEAT) ............................................ 31

Playing tracks in random order (RANDOM) .................................. 31

Ejecting the disc .......................................................................... 31

Displaying a genre for a CDs ....................................................... 32

Switching the display priority ....................................................... 33

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the tuner .......................................... 34

Tuning to a station ....................................................................... 34

Entering stations into memory automatically

(The automatic preset mode: ASM) ............................................. 35

Manually setting stations into memory ......................................... 36

Preset station scan ...................................................................... 37

FM reception characteristics ........................................................ 38

How to use the Card remote control ........................ 41

Precautions in use of the remote control ...................................... 41

Cleaning the remote control ........................................................ 41

Turning the power on/off ............................................................. 42

Adjusting the audio volume .......................................................... 42

Switching playback modes .......................................................... 42

How to play the tuner .................................................................. 43

How to play CDs ......................................................................... 44

Switching the remote control settings .......................................... 45

Replacing the battery .................................................................. 46

How to use an optional NOB remote control ........... 47

Turning the power on/off ............................................................. 47

Adjusting the audio volume .......................................................... 47

Switching playback modes .......................................................... 48

How to play the tuner .................................................................. 48

How to play CDs ......................................................................... 49

Illuminating the NOB remote control ............................................ 50

Enabling the optional E-COM feature ........................................... 50

Switching the remote control settings .......................................... 51

Replacing the battery .................................................................. 52

How to operate the receiver with an optional CD

changer connected ................................................... 54

Basic operation ........................................................................... 54

Displaying a genre for a CDs ...................................................... 57

Switching the display priority ...................................................... 58

How to operate the receiver with an optional

DSP/EQ unit connected ............................................ 59

How to operate the DSP functions .............................................. 59

How to operate the EQ functions ................................................ 63

Download from Www.Somanuals.com. All Manuals Search And Download.

If you have a question: .............................................. 66

Displaying information (for troubleshooting) .................................. 67

Specifications ............................................................ 70

Before installation .......................................................72

Components ............................................................................... 72

Setting the system-selector switch .............................................. 72

Mounting Instruction...................................................73

Mounting the main unit................................................................. 73

Names of lead wires and destinations ......................................... 75

System ........................................................................................ 76

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating precautions

◆ Operating Precautions

<Your CD3431 will perform well over a long period of time through correct

handling and care.>

Notes on Operation

• For your safety, play only at volume levels that allow outside sounds to

be heard.

• Use only audio compact discs.

This player can only play compact discs

bearing the logo shown to the left.

• It may not be possible to play back some

tracks on CD-Rs.

• It may not be possible to play back CD-Rs

with certain characteristics, or CD-Rs

which are scratched, dirty, or which have

been left inside a vehicle for long periods.

• CDs cannot be played back until all

sessions recorded on the CD-R have been

closed.

• CD-RW discs cannot be played back.

• Do not insert anything other than a CD into

the disc slot.

Do not insert any foreign objects, such as

coins or credit cards, into the disc slot. Be

especially watchful of children’s mischief in

this regard.

• Avoid severe mechanical shock.

When the player is subjected to severe

vibration while traveling over a rough

surface, playback may be intermittent.

When a situation like this occurs, resume

playback after returning to a smoother

road.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating precautions

• About dew condensation

In cold or rainy weather, just as the interior

glass surface gets fogged, dew (water

condensation) may also settle on the

deck. When this occurs, disc playback

may become intermittent or impossible.

Dehumidify the air in the vehick for a while

before resuming playback.

• Cleaning the disc slot

The disc slot tends to get dusty. Clean it

occasionally to prevent accumulated dust

from scratching the discs.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating precautions

About compact discs

• The signal recorded on a compact disc is read by a laser beam, so

nothing touches the disc surface. A scratch on the recorded surface or

a badly warped disc may cause deteriorated sound quality or

intermittent playback. Observe the following precautions to ensure high

quality sound performance:

• Do not leave an ejected disc in the disc

slot for very long; the disc may warp.

Discs should be stored in their cases and

kept away from high temperature and

humidity.

• Do not stick a piece of paper or tape on,

nor write on or scratch, either side of a

disc .

• Discs spin at a high speed inside the

deck. Keep cracked or warped discs out

of the player to avoid damaging it.

• Avoid touching the recorded surface when

handling a disc; handle discs by their

edges.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating precautions

About CD accessories

About brand new CDs

• You may notice that some brand

new discs are rough around the

center hole or outside edge.

Remove the rough edges with

the side of a ballpoint pen, etc.

Rough edges may prevent

proper loading in the deck.

Flakes from the rough edges

may also stick to the recorded

surface and interfere with

playback.

• Do not use accessories

(stabilizers, protective seals, laser

lens cleaners, etc.) sold for

“improving sound performance”

or “protecting CDs.” The

changes in CD thickness or

outside dimensions made by

these accessories may cause

problems in the player.

Rough Edges

Ballpoint

pen

• Please be sure NOT to attach

any ring-shape protector(or

other accessory) to your discs.

Those protectors are commercially

available and said to protect disc

and to improve sound quatily(and

antivibration effect), but they can

do more harm than good in

regular uses. The most common

problems are Insert /Eject

related problems and "No

playback" problems due to the

protectorring that came off in the

disc machanism.

Rough

Edges

Flakes

Recorded surface

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating precautions

About borrowed CDs

About irregularly-shaped CDs

• Specially-shaped CDs, like

heart-shaped or octagonal CDs,

cannot be played. Do not

attempt to play them, even with

an adapter, since they may

damage the player.

• Do not use a CD with glue or

remnants of adhesive tape or

labels. They may cause the CD

to get stuck inside or damage

the deck.

How to remove CDs

• When removing the ejected disc,

pull it straight out along the slot.

Pressing downward in the

process may scratch the

recorded surface of the disc.

OKAY

About cleaning a CD

• Use a commercially available compact disc

cleaner to clean a CD, wiping lightly from

the center to the edge.

• Do not use benzine, thinner, LP record

spray or other cleaners on CDs. They may

damage a CD’s finish.

XXXX

Download from Www.Somanuals.com. All Manuals Search And Download.

Names of controls and parts

◆ Names of controls and parts

Front View

[M ODE] button

[FUNC] button

[E-COM ] button※

[　 (EJECT)] button

DISC SLOT

[RESET] [SOURCE]

Buttons

[1] to[6]

[CUSTOM ] button

button

[AUDIO CONTROL] button

[ TU ] button

[ BND ] button

※NOTE：Double function button→"E-COM"&"MUTE" functions

• Though the words "press" and "tap" are used in the text for

the operation of the

[

]

button, and

[

BND

]

button, the button is actually slid in the

direction.

Download from Www.Somanuals.com. All Manuals Search And Download.

ESN (Key CD) security operating procedure

[FUNC] button

Button [1]

◆

ESN (Key CD) security operating

procedure

■ How to program the Key CD

1 . Turn off the main unit power.

2 . Press and hold button [1], then the [FUNC]

button, and hold both for more than one

second.

A [SEC] message appears, then in two seconds it will

change to [DISC].

The CD3431 is now ready to accept your Key CD in the

CD slot.

3 . Insert the CD into the slot.

A [SEC] message appears, the Key CD is ejected.

Download from Www.Somanuals.com. All Manuals Search And Download.

ESN (Key CD) security operating procedure

[FUNC] button

Button [1]

• If there is a problem with the inserted CD, an [ERR]

message will appear for two seconds and the CD will be

ejected. Reinsert the ejected CD.

• If a CD causes the [ERR] message to appear twice in a

row, a [CHANGE] message will appear for two seconds.

Try another CD.

• The Security indicator will flash whenever the vehicle’s

ignition is switched off.

■ How to cancel the Key CD

1 . Turn off the main unit power.

2 . Press and hold button [1], then the [FUNC]

button, and hold both for more than one

second.

A [SEC] message appears, then in two seconds it will

change to [DISC].

The CD3431 is now ready to accept your Key CD in the

3 . ^{CD slot.}

Insert your Key CD into the slot.

A [CANCEL] message appears, the Key CD is ejected.

The Key CD is cancelled.

Download from Www.Somanuals.com. All Manuals Search And Download.

ESN (Key CD) security operating procedure

•

This process cancels the protection for the ESN

deck.

• If power to the CD3431 is disconnected, then

reconnected, a key CD will not need to be inserted in

order to return the unit to normal operation.

• Inserting a CD other than the Key CD will not cancel the

protection. Instead, the display will show [ERR] for two

seconds, then the normal CD playback mode will activate.

■ How to change the Key CD

1 . First, cancel the existing Key CD.

Refer to “How to cancel the Key CD.”

2 . Next, program a new Key CD.

Refer to “How to program the Key CD.”

Download from Www.Somanuals.com. All Manuals Search And Download.

ESN (Key CD) security operating procedure

■ How to resume normal operation

(ESN security lock out)

If power to the CD3431 is disconnected while ESN security

is active (a Key CD was programmed), operation is disabled

until power is restored and the unit unlocked. Follow this

procedure to resume normal operation.

1 . When the power is turned on after

disconnecting the battery power, a [SEC]

message will appear for two seconds.

Thereafter, the message changes to [DISC]

and the CD3431 is ready to accept your Key

CD into the slot.

2 . Insert your Key CD.

If the correct CD is inserted, an [OK] message will

appear for two seconds and the CD will begin playing.

• If an incorrect CD is inserted, an [ERR] message will

appear for two seconds, after which the CD will be

ejected.

• You must use the same CD used for Key CD

programming; a duplicate CD may not work properly.

Download from Www.Somanuals.com. All Manuals Search And Download.

ESN (Key CD) security operating procedure

[FUNC] button

Button [6]

■ What happens if an incorrect CD is

inserted?

1 . An [ERR_] message will be appear, then

change to a flashing [DISC], then the CD will

be ejected.

You will have five uninterrupted attempts to insert the

correct CD.

2 . After the 5 incorrect attempt, the display

reads [HELP] .

3 . If [HELP] appears on the display, press button

[6], then the [FUNC] button, and hold them for

five seconds .

4 . Press the [FUNC] button.

You will have five more attempts to insert the correct

disc.

•

Number of errors: Numbers indicated the number of

errors that occurred.

●Note●

If after 10 tries the correct Key CD is not insereted, the

display reads [CALL 800]; the unit must be returned to

Eclipse to be reset. In this case, please contact your

Eclipse dealer for assistance or call Eclipse directly at

(800)233-2216

Your key CD can be easily forgotten. W rite

the album nam e in a rem indernote (Pg.83).

Download from Www.Somanuals.com. All Manuals Search And Download.

ESN (Key CD) security operating procedure

[FUNC] button

Button [2] Button [4]

■

How to turn the Security indicator on/off

Once ESN security is activated, the indicator flashes

whenever the vehicle’s ignition is turned off, warning

potential thieves that the unit is protected. However, if you

do not want this visible deterrent, it may be turned off.

1 . With the power is turned off, press button[2],

then [FUNC] button and hold both for more than a

second.

2 . [INDICATOR flash] or [INDICATOR OFF] appears

on the display.

[IND.FLASH] means the security indicator will flash when

the vehicle’s ignition is off, and [IND. -----] means it will

not. Repeat the above steps to reactivate the flash

mode.

■

How to Read the Electronic Serial

Number

1 . Turn off the main unit power.

2 . Press button [4], then the [FUNC] button, and hold

both for more than a second.

[ESN] appears on the display, followed by an eight-digit

number; this number is your electronic serial number (ESN).

You may use this number to identify your Eclipse CD3431

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operation

[SOURCE] button

[ BND ] button

[ TU ] button

Buttons [1] to[6]

Basic operation

◆

This section covers basic operating procedures.For

additional details, please refer to the sections on specific

functions.

■ Turning the power on and off

1 . Press the [SOURCE] button.

Less than two seconds : Each tap will switch

modes from Tuner→

Disc→PWR OFF (Stand by).

More than two seconds : Off

• If a car is not equipped with an ACC position (for example,

a European car), keep the [SOURCE] button depessed for

more than two seconds.

■ Listening to a CD

1 . Insert a CD into the disc slot, label side up.

The CD will immediately start playing.

• When a CD is already loaded, pressing the [SOURCE]

button repeatedly to switch to the CD mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operation

■ Listening to the tuner

1 . Press the [SOURCE] button repeatedly to

switch to the tuner mode.

This will turn the tuner on.

To turn the tuner off, press the [SOURCE] button either

shorter to select another mode or longer to turn the

power off.

2 .Tap the [ BND ] button to switch to the

desired FM or AM bands.

[

] button: Switch the FM band.

Pressing the button repeatedly switches the

FM band in the order of FM1→FM2→FM3.

] button: Switch to the AM band.

[

3 . Press the [ TU ] button to tune to a station.

A tap on either the [ ] or [ ] button for less than one

[

TU ] second will enable manual station tuning. Hold

one button down for more than two seconds to start the

automatic station search.

[

] button: Starts searching toward higher frequencies.

] button: Starts searching toward lower frequencies.

• If stations have been stored in memory, pressing a button

from [1] to [6] will directly select a station. (Refer to the

section “Manually setting stations into memory” on page

36.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operation

[E-COM ] button

[FUNC] button

[SOURCE] button

[ BND ] button

[AUDIO CONTROL] button

■ Adjusting audio volume

1 . Turn the [AUDIO CONTROL] button to the

left or right.

Turn to the left : Decreases the volume.

Turn to the right : Increases the volume.

•Press and hold the [E-COM] button for more than two

seconds if E-COM is connected and less than two

seconds if E-COM is not connected to activate or

cancel MUTE function.

■ Displaying the clock

1 . Press the [FUNC] button for more than one

second .

2 . Press the [ BND ] button repeatedly until

the [CLOCK OFF] display appears on the

screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operation

3 . Press the [SOURCE] button to switch to the

[CLOCK ON] display.

4 . Press the [FUNC] button again.

Refer to the section on“setting the clock”to set

the time display.

■ Others

▼

Disabling the guide tone feature (for button

operation)

The receiver is set at the factory to emit a beep tone in

response to button operation. The guide tone feature may

be disabled in the following procedure:

1 . Press the [FUNC] button for more than one second.

2. Press the [ BND ] button repeatedly until [BEEP

ON] display appears on the screen.

3. Press the [SOURCE] button to switch to the [BEEP

OFF] display.

4. Press the [FUNC] button again.

▼

Contrast adjustment

Adjust the display contrast to the best level in accordance

with the angle of viewing.

1 . Press the [FUNC] button for more than one second.

2. Press the [ BND ] button repeatedly until [CONT]

display appears on the screen.

3. Press the [SOURCE] button to change contrast.

4. Press the [FUNC] button again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operation

[M ODE] button

[FUNC] button

[SOURCE] button

[ BND ] button

[CUSTOM ] button

[AUDIO CONTROL] button

▼

Setting the clock

This receiver uses the 12-hour, A.M./P.M.display notation.

1 . Press the [FUNC] button for more than one second.

2 . Press the [CUSTOM] button to switch to the clock

adjustment mode.

3 . Press the [SOURCE] button to select the hour or

minutes to be adjusted.

The blinking one can be adjusted.

4 . Press the [ BND ] button.

[

]button : Turns the time forward.

]button : Turns the time back.

5 . Press the [CUSTOM] button again to return to the

normal mode.

•To set the clock to 0 minutes, 0 seconds (an exact hour),

press the [MODE] button.

For example:

At 3:29: Pressing the [MODE] button returns to 3:00.

At 3:30: Pressing the [MODE] button advances to 4:00.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operation

▼

Switching audio control modes

Various audio control modes may be fine-tuned using this

procedure.

1 . Press the [AUDIO CONTROL] button for less than

one second.

Pressing the button repeatedly will allow you to control

adjustments of [BASS] (low frequencies), [TREB] (high

frequencies), [FADER] (front-rear speaker balance),

[BAL] (left-right speaker balance), and [SUB-W]

(subwoofer level).

2 . Turn the [AUDIO CONTROL] button to the left or

right

It controls levels and adjust the sound to your

preference.

•When Tone Control feature is off, adjustment of BASS and

TREB will be skipped.

• When an optional DSP/EQ unit is connected, the mode

switches from Volume → DSP level adjustment → EQ level

adjustment. BASS, TREB, FADER, BAL, may be skipped,

and it depends on the type of DSP/EQ and its situation.

▼

Enabling the loudness control

The loudness control may be turned on to emphasize low

and high frequencies at low volume levels.

Loudness compensates for the apparent weakness of low

and high frequencies at low volume by boosting the bass

and treble levels.

1. Press and hold the [AUDIO CONTROL] button until

the [LOUD ON] display appears on the screen.

• To disable the loudness feature, repeat the above

procedure to display the [LOUD OFF] indication.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operation

[FUNC] button

[E-COM ] button

[SOURCE] button

[ BND ] button

▼

Switching Non-Fader modes

1 . Press the [FUNC] button for more than one second.

2 . Press the [ BND ] button repeatedly until the

[PHASE NORM] display appears on the screen.

3 . Press the [SOURCE] button.

Each press of the button switch modes between the

Normal and Reverse.

4 . Press the [FUNC] button again.

Pressing the button will cancel Function mode.

Disabling the Tone Control feature

1 . Press the [FUNC] button for more than one second.

2 . Press the [ BND ] button repeatedly until the

[TONE ON] display appears on the screen.

3 . Press the [SOURCE] button.

Pressing the button will switch the tone control feature

on or off.

4 . Press the [FUNC] button again.

Pressing the button will cancel Function mode.

Enabling E-COM feature

1 . Press the [E-COM] button for one second.

Pressing the button will switch the E-COM feature on or

off.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the CD player

[SOURCE] button

[ BND ] button

◆ How to operate the CD player

First press the [SOURCE] button to switch to the disc mode.

It is assumed here that a CD has already been loaded into

the unit.

■ Listening to CDs

1 . Press the [SOURCE] button.

This turns on the disc mode and starts CD play.

If an external CD changer is connected, each additional

tap of the [ BND ] button will switch modes from CD

changer 1 CD changer 2 CD player.

A changer or player with no discs loaded will be

skipped.

● Caution ●

•Playback may be intermittent when there is a scratch on a

CD or when the recorded side is dirty.

•Only two external CD changers may be connected.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the CD player

Button [4]

[ TU ] button

■

Advancing to the next track or returning to

the beginning of the track being played

1 . Press the [ TU ] button.

[

] button: Advances to the next track.

] button: Returns to the beginning of the track being

played.

• Pressing and holding the [ ] button will fast-forward

through a track, while pressing the [ ] button will fast-

reverse.

■

Playing the beginning of tracks (SCAN)

1 . Press button [4 (SCAN)].

Tapping the button causes the player to move up to

the next track and play it for 10 seconds, then move

up to the next track and play it for 10 seconds, and so

on until the button is tapped again.

•To continue playing a desired track, press the button again

to stop scanning.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the CD player

[　 (EJECT)] button

Buttons [5] to[6]

■

Repeating the same track (REPEAT)

1 . Press button [5 (RPT)] to repeat the track being

played.

To cancel, press button [5] again.

Playing tracks in random order (RANDOM)

1 . Press button [6 (RAND)] to play the tracks in

random order.

To cancel, press button [6] again.

• Occasionally the same track happens to be played

(selected) two or more times in a row; this is normal

operation and is no sign of a problem.

■ Ejecting the disc

1 . Press the [ （EJECT）] button.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the CD player

[M ODE] button

[FUNC] button

■ Displaying a genre for a CDs

A preset genre can be assigned to individual CD and

displayed when they are played.

1 . Press the [FUNC] button for more than one

second.

2 . Press the [MODE] button.

Nine genre are available for a CD in the following

sequence;

1.JAZZ

2.POPS

3.ROCK

4.FUSION

5.BALLAD

6.GUEST

7.FAVORITE

8.BRANDNEW

9.DELETE

When the [DELETE] is selected, the genre will not be

displayed.

3 . Press the [FUNC] button again.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the CD player

[FUNC] button

[SOURCE] button

[ BND ] button

■ Switching the display priority

if a genre has been set, you can change the display priority

by the following procedure.

1 . Press the [FUNC] button for more than one

second.

2 . Press the [ BND ] button repeatedly until

[DISP A(B)] display appears on the screen.

3 . Press the [SOURCE] button to change the

display priority.

Pressing the button will switch the display A or B.

[DISP A] : Genre display has priority.

[DISP B] : Tracking/elapsed time display has priority.

4 . Press the [FUNC] button again.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the tuner

[ TU ] button

[SOURCE] button

[ BND ] button

◆ How to operate the tuner

First, press the [SOURCE] button to start tuner operation.

There are automatic and manual methods for setting stations

in memory. The receiver will accept up to 24 stations in

memory: six in AM and 18 in FM (6 each for FM1, FM2 and

FM3.)

■ Tuning to a station

1 . Tap the [ BND ] button to switch to the

desired FM or AM mode.

[

] button: Switch the FM band.

Pressing the button repeatedly switches the

FM band in the order of FM1→FM2→FM3.

] button: Switch to the AM band.

[

2 . Press the [ TU ] button to tune to a station.

Tap the [ ] or [ ] button for less than one second to

tune to a station manually.

To start searching for a station automatically, hold the

button down for more than one second.

[

] button: Tunes to higher frequencies.

] button: Tunes to lower frequencies.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the tuner

[M ODE] button

[ BND ] button

Buttons [1] to[6]

•At times, it may be difficult to maintain optimum reception

because the antenna affixed to your vehicle is in motion

constantly (relative to the broadcast antenna), encountering

continuous variation in the received radio signals’ strength.

Other factors affecting reception include interference from

natural obstacles, sign posts, etc.

■

Entering stations into memory automatically

(The automatic preset mode: ASM)

1 . Tap the [ BND ] button to switch to the

desired FM or AM mode.

[

] button: Switch the FM band.

Pressing the button repeatedly switches the

FM band in the order of FM1→FM2→FM3.

] button: Switch to the AM band.

[

2 . Press the [MODE] button for more than two

seconds until a beep is heard.

The automatic preset mode starts.

The [ASM] indicator on the screen flashes, and stations

are automatically entered in memory under buttons [1]

to [6].

These buttons are called preset buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the tuner

[ TU ] button

[ BND ] button

Buttons [1] to[6]

• Press any numbered button to select the station whose

frequency is indicated right above the button.

•When a new station is set in memory, the station previously

set in memory will be deleted.

• If the number of receivable stations fewer than six, the

stations set in the rest of the preset buttons will be retained.

■

Manually setting stations into memory

This section covers the setting of stations in memory under

the numbered buttons.

1 . Press the [ BND ] button to switch between

FM and AM.

2 . Use the [ TU ] button to tune to the station

to be entered in memory.

3 . Select any button, from [1] to [6], and press it

for more than two seconds.

The tuned station is now memorized and set in the

button selected. Repeat the procedure to set additional

manually tuned stations in memory, in turn, for buttons

[1] to [6]. These buttons are called the preset buttons.

● Caution ●

•If the vehicle’s battery is disconnected (for repairs to the

vehicle or for removing the receiver), all stations in memory

will be lost. In such a case, set stations in memory again.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the tuner

[M ODE] button

■

Preset station scan

This function enables reception of all the stations in the

numbered preset buttons for five seconds each.

1 . Press the [MODE] button.

[P SCAN] will appear at the top of the display, and

stations stored under preset buttons [1] through [6] will

beplayed for five seconds each.

2 . To stop the scan mode at a desired station,

press the [MODE] button again.

The receiver will stay tuned to the desired station.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the tuner

■ FM reception characteristics

In general, FM has much better tonal quality than AM.

However, FM and FM stereo reception encounter several

characteristic problems not encountered with AM. FM is

more difficult to receive than AM in a moving vehicle. The

following are explanatory notes on what to expect from FM

reception and on how to get satisfactory performance.

1 . FM RECEPTION DIFFERS FROM AM

A characteristic of transmitted signals is that lower

frequencies travel further. FM frequencies are much

higher than AM’s (similar to a ray of light): they won’t

bend but they will reflect. Often, they will be interrupted

by tall buildings, mountains, etc., taking direct and

indirect paths to your vehicle’s antenna. The distance at

which FM stations can be received satisfactorily is

usually not nearly as far as that which AM stations can

be received.

AM Radio Waves

FM Radio Waves

Ionosphere

2 . FADING OUT

In weak signal or “fringe” reception areas, FM stations

may fade out completely, or fade in and out. When

driving in weak signal areas, such as near hills, through

valleys or tunnels, among tall buildings, etc., you may

encounter unusual noise interference. THIS IS NOT A

TUNER PROBLEM. In this case, you can only wait until

you are in a better reception area, tune to a stronger

station, or reduce the treble level.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the tuner

3 . RECEPTION AREA OF FM BROADCASTS

A home receiver can catch weak FM stereo signals

through the use of a tall, directional or ultra-sensitive

antenna. In a moving vehicle, the area for good

reception is limited because of varying conditions

encountered while driving, including the types and

heights of broadcast antenna structures, signal

strength, engine noise, etc. For best reception with

manual antenna, extend the antenna mast as far as

possible.

Transmitting Antenna 100 Meters High

Effective Radiation Power 1kW

FM Stereo Auto Radio 20 km

FM Monaural Auto Radio 50 km

Home FM Stereo Receiver 100 km

Reception quality varies depending on the power of the FM

station, natural and artificial barriers,weather conditions, etc.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the tuner

4 . MULTIPATH

The reflection characteristics of FM waves cause

another problem called multipath–FM wave signals

reflecting off of buildings, mountains, etc. When the

antenna receives direct and reflected waves at the same

time, distortion of sound in the treble range often

occurs, such as static or a harsh-sounding voices. THIS

IS NOT A TUNER PROBLEM. Only moving to another

area with a clearer signal path can remedy the situation.

DIRECT

WAVE

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use the Card remote control

◆

How to use the Card remote

control

Precautions in use of the remote control

• Be careful when handling the control, especially because it is

small and light. Dropping or striking it hard may damage it,

wear out the battery or cause a malfunction.

• Keep the remote control free of moisture, dust and water. Do

not subject it to shock.

• Do not place the remote control unit where it will get hot,

such as on the dashboard or near a heater vent. Allowing the

remote control unit to overheat may warp its case or cause

other problems.

• Do not operate the remote control unit while driving because

doing so could cause an accident.

• When using the remote control,point it directry at the remote

control light receptor.

• The light receptor may not operate correctly if it is exposed to

bright light such as direct sunlight.

• Be sure to press the [SOURCE] button on the main unit for

more than two seconds to shut it down before leaving the

car, or the car battery may be run down. When the main unit

is shut down, the remote control will not work.

• Remove the batteries from the remote control unit whenever

it is not to be used for a long time.

Cleaning the remote control

• Use a dry cloth to keep the unit clean, If the remote control

unit gets extremely dirty, clean it with a cloth moistened in

dilute liquid detergent. Do not use alcohol or thinner; these

compounds may damage the finish.

• In no event should benzine or thinner be used. These

substances will damage the case or finish.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use the Card remote control

[MODE] button

[PWR]

button

Remote-control

light receptor

[+] button

[-] button

[MUTE]

button

■ Turning the power on/off

1 . Press the [PWR] button.

The power turns on or off each time the button is pressed.

•When the main unit is shut down, the remote control will

not work.

■ Adjusting the audio volume

1 . Press the [+] or [-] button.

[+] button: Increases the volume.

[ -] button: Decreases the volume.

▼

Cutting the volume instantly (muting):

Press the [MUTE] button for more than two seconds to cut

the volume or restore it instantly.

•Press and hold the [MUTE] button for more than two

seconds if E-COM is connected and less than two

seconds if E-COM is not connected to activate or

cancel MUTE function.

■ Switching playback modes

1 . Press the [MODE] button.

Tap the button to switch modes in the following

sequence:

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use the Card remote control

[

] button

BAND

[

] buttons

TUNE･SEEK

PRESET CH

■ How to play the tuner

Enter the tuner mode first.

▼

Select the FM/AM band

1. Tap the [BAND] button.

Each tap will switch tuner modes from FM1 → FM2 →

FM3 → AM.

▼

Select a station (manually or automatically)

A short tap of the button will allow manual station tuning.

Pressing for more than one second will start automatic

tuning.

1. Press the [ TUNE•SEEK ] button.

[

] button: Tunes to higher frequency stations.

] button: Tunes to lower frequency stations.

▼

Selecting preset stations

A total of six stations may be selected (preset tuning) out of

those already set in memory through the main unit. (Refer to

“Manually setting stations into memory,” page 36.)

1. Press the [ PRESET CH ] button.

[

]

button: Selects the next higher number preset button.

button: Selects the next lower number preset button.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use the Card remote control

[

] button

BAND

[

] buttons

TRACK･APS

[

] buttons

DISC

■ How to play CDs

Select the disc mode first.

▼

Switching disc modes

1. Press the [BAND] button.

When one or two CD changer is connected, tap the

[BAND] button to change modes from CD player → CD

changer 1 → CD changer 2.

The indicator will skip a changer or player that has no

discs loaded.

▼

Advancing to the next track or returning

to the beginning of the track being played

1. Press the [ TRACK•APS ] button.

[

] button: Skips to the next track.

] button: Returns to the beginning of the track being

played.

• Hold the [ ] button down to fast-forward, or the [

]

button to fast-reverse the track being played.

▼

Skipping to the next or previous CD.

1. Press the [ DISC ] button.

[

] button: Selects the next higher number disc.

] button: Selects the next lower number disc.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use the Card remote control

[

] buttons

TRACK

DISC

[

] button

CUSTOM

■ Switching the remote control settings

Remote control functions can be switched to the three

patterns.

1. Press the [CUSTOM] button of the main unit for

about one second.

2. Each time the button is pressed, the pattern is

switched in the order of A, B, and C so that the

E-com function can be supported.

REMOTE A---Conventional functions

REMOTE B---

[DISC ] button---Repeat

[DISC ] button---Answer

[TRACK ] button---Next

[TRACK ] button---Previous

Other functions than the above are conventional functions.

REMOTE C---

[DISC ] button---Option4

[DISC ] button---Option3

[TRACK ] button---Option2

[TRACK ] button---Option1

Other functions than the above are conventional functions.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use an optional NOB remote control

■ Replacing the battery

Use one CR2025 battery.

1 . On the back of the remote control, while

pressing the locking knob on the battery slot

cover toward your right, pull out the battery

carier with your fingernail.

UNLOCK

2 . Remove the old battery, then place the new

one in the carrier with the (+) mark facing up.

3 . Push in the carrier until it snaps into place.

●Caution ●

Be extremely careful not to swallow the battery.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use an optional NOB remote control

[AUDIO

CONTROL]

button

Remote-control

light receptor

[MUTE] button

[PWR] button

◆ How to use an optional NOB

remote control

■ Turning the power on/off

1 . Press the [PWR] button.

The power turns on or off each time the button is pressed.

•When the main unit is shut down, the remote control will

not work.

■ Adjusting the audio volume

1 . Press the [AUDIO CONTROL] button, and turn

it to the left or right.

Each tap of the button will switch the audio control

modes.

Turn to the right: Increases the volume.

Turn to the left : Decreases the volume.

▼

Cutting the volume instantly (muting):

Press the [MUTE] button for more than two seconds to

cut the volume or restore it instantly.

•Press and hold the [MUTE] button for more than two

seconds if E-COM is connected and less than two

seconds if E-COM is not connected to activate or

cancel MUTE function.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use an optional NOB remote control

[BAND] button

TUNE SEEK ] buttons

[MODE] button

[

■ Switching playback modes

1 . Press the [MODE] button.

Tap the button to switch modes in the following

sequence:

■ How to play the tuner

Enter the tuner mode first.

▼

Select the FM/AM band

1. Tap the [BAND] button.

Each tap will switch tuner modes from FM1 → FM2 →

FM3 → AM.

▼

Select a station (manually or automatically)

A short tap of the button will allow manual station tuning.

Pressing for more than a second will start automatic tuning.

1. Press the [ TUNE•SEEK ] button.

[

] button: Tunes to higher frequency stations.

] button: Tunes to lower frequency stations.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use an optional NOB remote control

BAND

MODE

[BAND] button

・

TRACK

TUNE SEEK

[

TRACK ] buttons

DISC

[

DISC ] buttons

E-COM

MUTE

PWR

ILLUMI

▼

Selecting preset stations

A total of six stations may be selected (preset tuning) out of

those already set in memory through the main unit. (Refer to

“Manually setting stations into memory,” page 36.)

1. Press the [ DISC ] button.

[

]

button: Tunes the next preset number at a higher frequency.

button: Tunes the next preset number at a lower frequency.

■ How to play CDs

Select the disc mode first.

▼

Switching disc modes

1. Press the [BAND] button.

When the CD changer is connected, tap the [BAND]

button to change modes from CD player → CD changer

1 → CD changer 2.

The indicator will skip a changer or player that has no

disc loaded.

▼

Advancing to the next track or returning

to the beginning of the track being played

1. Press the [ TRACK ] button.

[

] button: Skips to the next track.

] button: Returns to the beginning of the track being

played.

• Hold the [ ] button down to fast-forward, or the [

]

button to fast-reverse the track being played.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use an optional NOB remote control

[

DISC ] buttons

[E-COM] button

[ILLUMI] button

▼

Skipping to the next disc or back to the

beginning of track being played.

1. Press the[ DISC ] button.

[

] button: Advances the disc number to the upper

(next) disc.

[

] button: Returns the disc number to the lower

(previous) disc.

■ Illuminating the NOB remote control

The buttons of the NOB remote control will be illuminated by

pressing the [ILLUMI] button.

■ Enabling the optional E-COM feature

Pressing the [E-COM] button for one second will switch the

E-COM feature on or off.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use an optional NOB remote control

[

TRACK ] buttons

DISC ] buttons

[CUSTOM] button

■ Switching the remote control settings

Remote control functions can be switched to the three

patterns.

1. Press the [CUSTOM] button of the main unit for

about one second.

2. Each time the button is pressed, the pattern is

switched in the order of A, B, and C so that the

E-com function can be supported.

REMOTE A---Conventional functions

REMOTE B---

[DISC ] button---Repeat

[DISC ] button---Answer

[TRACK ] button---Next

[TRACK ] button---Previous

Other functions than the above are conventional functions.

REMOTE C---

[DISC ] button---Option4

[DISC ] button---Option3

[TRACK ] button---Option2

[TRACK ] button---Option1

Other functions than the above are conventional functions.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use an optional NOB remote control

■ Replacing the battery

Use two AA cell batteries.

1 . Remove the back cover of the remote control

unit by gently pressing and sliding it in the

direction indicated by the arrow.

2 . Install the two batterles provided into the

compartment as illustrated inside the

compartment.

3 . Return the back cover into place by sliding it in

the direction indicated by the arrow.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use an optional NOB remote control

●Caution ●

・Be extremely careful not to swallow the battery.

・The battery life is approximately one year. If the

remote control unit does not operate correctly or if

the button lump gets dim, replace the batteries.

・Be sure to orlent the batteries correctly so that the

positive and negative poles match the diagram.

・Do not use one new battery and one old one; use

two new batteries.

・Use only two of the same kind of battery.

・If any liquid is seen leaking from the batteries,remove

both batteries and dispose of them properly.

Thoroughly clean the battery compartment with a

dry cloth. Then install new batteries.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the receiver with an optional CD changer connected

[ TU ] button

[SOURCE] button

[ BND ] button

◆

How to operate the receiver with an

optional CD changer connected

■ Basic operation

This section covers the operation of the CD changer that is

connected to the receiver.

To switch from another mode, press the [SOURCE] button.

▼

Listening to a CD

1. Press the [ BND ] button

Each press of the button switches the mode from CD

Player →CD Changer 1 → CD Changer 2.

▼

Advancing to the next track or returning

to the beginning of the track being played

1. Press the [ TU ] button.

[

] button: Advances to the next track.

] button: Returns to the beginning of the track being

played.

• Hold down the [ ] button to fast-forward, or the [

]

button to fast-reverse within the disc being played.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the receiver with an optional CD changer connected

Buttons [4] to[6]

▼

Playing the beginning of tracks (SCAN):

1. Press button [4 (SCAN)].

Tapping the button causes the changer to move up to

the next track and play it for 10 seconds, then move up

to the next track and play it for 10 seconds, and so on,

on one CD, until the button is tapped again.

Hold the button until the [ALL SCAN] display appears

to play the first 10 seconds of the first track of every CD

loaded.

▼

Repeating the same track (REPEAT):

1. Press button [5 (RPT)].

Tapping on the button causes the changer to repeat

the track currently being played, until the button is

tapped again.

Hold the button until the [ALL REPEAT] display appears

to repeat all tracks on the CD being played.

Playing tracks in random order (RANDOM):

1. Press button [6 (RAND)].

Tapping on the button causes the changer to play the

tracks on the currently playing CD in random order.

Hold the button until the [ALL RANDOM] display

appears to play tracks from all of the CDs (loaded in

the currently selected changer) in random order.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the receiver with an optional CD changer connected

[M ODE] button

Buttons [1] to[6]

•Occasionally the same track happens to be played

(selected) two or more times in a row, but it is no sign of

a problem.

•When any of the functions - “Playing the beginning of

tracks,” “Repeating the same track” and “Playing tracks

in random order” - is selected, a message such as

[SCAN], [ALL-SCAN], [REPEAT], [ALL-REPEAT],

[RANDOM] or [ALL-RANDOM] is displayed at the

bottom of the screen to verify the current function.

▼

Skipping to the next or previous CD

1. Press either button [1(

DISC

] or [2(

) DISC

)].

Button [2(

DISC

)] : Selects the next higher number disc.

Button

[1(

DISC

)]

Selects the next lower number disc

Specifying a CD to play

A CD of your choice is directly selectable out of the loaded

discs.

1. Press the [MODE] button for less than one second.

2. Press a button from [1] to [6].

Buttons

CDs*

10 11 12

To select a CD from no. 7 to 12, press the

desired button considerably longer.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the receiver with an optional CD changer connected

[M ODE] button

[FUNC] button

■ Displaying a genre for a CDs

A preset genre can be assigned to individual CD and

displayed when they are played.

1 . Press the [FUNC] button for more than one

second.

2 . Press the [MODE] button.

Nine genre are available for a CD in the following

sequence;

1.JAZZ

2.POPS

3.ROCK

4.FUSION

5.BALLAD

6.GUEST

7.FAVORITE

8.BRANDNEW

9.DELETE

When the [DELETE] is selected, the genre will not be

displayed.

3 . Press the [FUNC] button again.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the receiver with an optional CD changer connected

[FUNC] button

[SOURCE] button

[ BND ] button

■ Switching the display priority.

If a genre has been set, you can change the display priority

by the following procedure.

1 . Press the [FUNC] button for more than one

second.

2 . Press the [ BND ] button repeatedly until

[DISP A(B)] display appears on the screen.

3 . Press the [SOURCE] button to change the

display priority.

Pressing the button will switch the display A or B.

[DISP A] : Genre display has priority.

[DISP B] : Tracking/elapsed time display has priority.

4 . Press the [FUNC] button again.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the receiver with an optional DSP/EQ unit connected

[FUNC] button

Button [1]

◆

How to operate the receiver with

an optional DSP/EQ unit connected

■ How to operate the DSP functions

The DSP feature adds reverberations to simulate ambience in

different types of surroundings (room sizes).

▼

Switching room sizes.

1. Press the [FUNC] button for more than one second.

2. Tap button [1] to switch room sizes for less than

one second.

Each tap of the button [1] will switch the room size.

Six room sizes are available for selection in the

following sequence:

1. CONCERT (a concert hall)

2. LIVE (a live house)

3. CATHEDRAL (a church with rich reverberations)

4. STADIUM (an outdoor stadium)

5. CLUB

6. DEFEAT (DSP OFF)

3. Push the [FUNC] button.

This cancels the adjustment mode; the selected room

size will now take effect.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the receiver with an optional DSP/EQ unit connected

[FUNC] button

Button [1]

•The following six patterns are preset at the factory:

Button

Indicator display

CONCERT

LIVE

CATHEDRAL

STADIUM

CLUB

CONCERT

▼

Fine-tuning an individual roomsize mode

Detailed adjustments are available in any of the room size

modes.

1. Press the [FUNC] button for more than one second.

2. Hold button [1] down for more than a second.

The DSP mode starts.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the receiver with an optional DSP/EQ unit connected

[AUDIO CONTROL] button

Buttons [1] to[6]

3. Tap button [AUDIO CONTROL] to select the desired

mode of adjustment.

The mode sequence on the button is as follows:

•

Level Duration value

(Reverberation duration)*

(Reverberation level)*

(Initial echo delay)

○○○

(Initial echo level)

The level and duration adjustments are available

in CONCERT and CATHEDRAL modes only.

4. Turn the [AUDIO CONTROL] button.

This button adjusts the reverberation level and duration.

Right: Increases the value.

Left: Decreases the value.

5. Hold down a button, [1] to [6], for more than two

seconds to preset a value.

The preset value is overwritten by the value set using

the above steps.

Direct (original sound)

Reverberation duration

High

Initial echo]

Level

Time

Long

Initial echo delay Reverberation

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the receiver with an optional DSP/EQ unit connected

[FUNC] button

Buttons [1] to[6]

6. Push the [FUNC] button.

The adjustment mode will be canceled and the

selected room size will now take effect.

▼

Retrieving a preset pattern from memory

Press a preset button to retrieve the room size in memory.

The buttons under which room sizes are stored in memory

are called preset buttons.

1. Press the [FUNC] button for more than one second.

2. Hold button [1] down for more than one second.

3. Press a button, [1] to [6] for less than two seconds.

The room size, as preset in the button, is retrieved.

4. Press the [FUNC] button to cancel the DSP

adjustment mode

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the receiver with an optional DSP/EQ unit connected

[FUNC] button

Button [2]

■ How to operate the EQ functions

The EQ functions enable level adjustments of various

frequency groups for optimum listening conditions with a

specific kind of music or musical instrument.

▼

Switching equalizer modes

1. Press the [FUNC] button for more than one second.

2. Tap button [2] to switch equalizer modes.

Six kinds of music categories are available for selection

in the following sequence:

1. POPS

2. ROCK

3. JAZZ

4. CLASSICAL

5. VOCAL

6. NEWS

7. DEFEAT （EQ OFF）

3. Push the [FUNC] button

The adjustment mode will be canceled and the

selected equalizer mode will now take effect.

•The initial EQ settings are factory preset.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the receiver with an optional DSP/EQ unit connected

[FUNC] button

[AUDIO CONTROL] button Buttons [1] to[6]

▼

Fine-tuning EQ functions

1. Press the [FUNC] button for more than one second.

2. Hold button [2] down for more than one second.

The EQ adjustment mode starts.

3. Tap button [2] until the desired equalizer mode is

displayed.

4. Tap the [AUDIO CONTROL] button to switch

frequencies.

The frequencies will switch in the following sequence:

63Hz 125Hz 250Hz 500Hz 1kHz 4kHz 12kHz

5. Turn the [AUDIO CONTROL] button to adjust the level.

Right :Increases the value.

Left :Decreases the value.

6. Hold down a button, [1] to [6], for more than two

seconds to preset a value.

The preset value is overwritten by the value set using

the above steps.

7. Push the [FUNC] button

This cancels the adjustment mode. The selected value

will now take effect.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to operate the receiver with an optional DSP/EQ unit connected

[FUNC] button

Buttons [1] to[6]

▼

Retrieving an equalizer mode from memory

Press a preset button to retrieve the equalizer mode set in

memory for the button.

The buttons that set equalizer modes in memory are called

preset buttons.

1. Press the [FUNC] button for more than one second.

2. Hold button [2] down for more than one second.

3. Press a button, [1] to [6] for less than two seconds

4. Press the [FUNC] button.

The selected equalizer mode will now take effect, and

the EQ adjustment mode will be canceled.

Download from Www.Somanuals.com. All Manuals Search And Download.

If you have a question:

[RESET] button

◆ If you have a question:

First check the items mentioned below before attempting to

troubleshoot problems.

●Caution●

• If a problem occurs, for instance when the unit does not

respond to any button presses, or the display doesn't

work press the [RESET] button using a sharp tool.

Pressing the [RESET] button will delete all the entries from

memory. The settings will return to those made at the

factory prior to shipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

If you have a question:

■ Displaying information

(for troubleshooting)

The information listed in the chart below is displayed to show

the status of the CD player and CD changer. Refer to the

chart for the appropriate action.

Infomation Code Table

When “INFO ”flash on the

indicator .

Nos.2-7 are displayed.

Infomation Contents

2 NO DISK LOADED IN

THE MAGAZINE

Explanation and remedial action to take.

There is no disc in the magazine or player.

Load adisc in the magazine.

（Load a music disc.）

The loaded disc is dirty or upside down.

Check it for proper orientation and verity it

is clean.

3 DISCS ARE DIRTY OR

DAMAGED

・The CD changer is inoperative for some

reason.Go through the magazine removal

procedure.

CD CHANGER FAILS

MECHANICALLY

・If a magazine fails to eject, have your dealer

fix the problem.

・The temperature in the CD changer is too

high for operation.Wait until it cools down.

・Resume playing after the “High

temperature sensed and CD stopped ”

display disappears.If the CD still cannot

play , have your dealer repair it.

6 WHEN THE CD CHANGER

INTERNAL TEMPERATURE

IS HIGH. （TO PROTECT

PICKUP UNIT）

7 AN INTERNAL POWER ・Tum the ACC off once before turning it on

SUPPLY FAILURE IS

OCCURRING WITH THE

AUTO CHANGER

once again to resumu the operation.

If the function still cannot be resctred,

ccntact your dealer.

・

Download from Www.Somanuals.com. All Manuals Search And Download.

If you have a question:

Remedial action Refer

to take to page

Mode

Common Dead or

to all weak sound

Problem

Causes

Is the volume control up sufficiently? Turn up the volume control. 24

Is the muting function in effect

(MUTE)?

Cancel the muting

(MUTE) function.

Is the fader or balance control set

far to one side?

Readjust the fader and

balance controls to more

normal positions.

Other probable causes include

broken audio-signal wiring or a

faulty speaker.

Have your dealer check

the problem.

Power does Are too many electrical items

Have your dealer check

not turn on. installed, causing a lack of power? the problem.

Other probable causes include a

run-down car battery, broken

power or interconnection wiring.

Have your dealer check

the problem.

Frequencies Has the car battery been disconnected Reenter them into

or titles set in for repair or checked out?

memory are

memory.

deleted.

Are too many electrical items

installed and causing lack of

available power?.

Have your dealer check

the problem.

Other probable causes include run- Have your dealer check

down car battery, broken power or the problem.

interconnection wiring.

No guide

tone sounds.

Is the guide tone disabled?

Is the battery low?

Enable the guide tone.

Replace battery.

The remote

control does

not work.

Is the battery installed in reverse

polarity?

Reinstall the battery in

the correct polarity.

Is direct sunlight hitting the remote Use the remote control

control light receptor?

close to the receptor.

Other probable causes include a

malfunctioning remote control.

Have your dealer check

the problem.

Download from Www.Somanuals.com. All Manuals Search And Download.

If you have a question:

Remedial action Refer

Mode

Problem

Causes

to take

to page

CD The disc cannot be inserted. Is an extra label or seal

The disc is ejected as soon applied to the disc?

as it is inserted.

Do not apply labels or seals 12

to the disc.

Or, the disc cannot be

ejected.

The disc cannot be

changed.

Are there rough edges,

deformations or

damaged areas on the

disc?

Try inserting another disc.

Removed any burrs. Do

not use a deformed or

damaged disc.

Sound skips around.

Sound is intermittent.

Sound is bad in quality.

Is the disc damaged?

Try another disc. Do not

(scratched, warped, etc.) play a damaged disc.

Is the disc clean? Clean the disc.

Is the player mounted at Have your dealer check it

a proper angle?

Is the player mounted

loosely?

out.

Are you driving over a

rough surface?

Avoid playback while

driving over rough surfaces. 10

Problem

Causes

Remedial action to take

Extend the antenna.

Receives no

stations, or

receives static

noise.

Is the antenna retracted?

Is the tuner correctly tuned to a

station?

Tune to a station.

Are you driving outside the service

area of your preset stations?

Tune to a local station.

(Please note, there may be

no local stations servicing

the area where you are

currently driving.)

Are you operating other equipment

with a computer, or a mobile phone,

in your vehicle at the same time as

your receiver?

Avoid operating such

equipment while using the

receiver.