Ni-MH Rechargeable Batteries
able of Contents
T
1 Introduction
2 General Characteristics
3 Composition and Chemistry
3.1 Active Components: Positive and Negative Electrodes
3.2 Electrolyte
3.3 Cell Reactions
4 Battery Construction
4.1 Basic Cell Construction
4.2 Cylindrical Cell Construction
4.3 Prismatic Cell Construction
5 Performance Characteristics
5.1 General Characteristics
5.2 Discharge Characteristics: Effect of Discharge Rate
and Temperature
5.5 Constant Power Discharge Characteristics
5.6 Polarity Reversal During Overdischarge
5.7 Internal Impedance
5.8 Self-Discharge and Charge Retention
5.9 Voltage Depression (“Memory Effect”)
5.3 Capacity: Effect of Discharge Rate
and Temperature
5.4 Energy Density
6 Charging Sealed Nickel-Metal Hydride Batteries
6.1 General Principles
6.3 Charging Methods
6.3.1 Duracell’s Recommendation:
Three-Step Charge Procedure
6.3.2 Low-Rate Charge
6.3.3 Quick Charge
6.2 Techniques for Charge Control
6.2.1 Timed Charge
6.2.2 Voltage Drop (-∆V)
6.2.3 Voltage Plateau (zero ∆V)
6.2.4 Temperature Cutoff
6.3.4 Fast Charge
6.2.5 Delta Temperature Cutoff (∆TCO)
6.2.6 Rate of Temperature Increase (dT/dt)
6.3.5 Trickle Charge
6.4 Thermal Devices
7 Cycle and Battery Life
7.1 Cycle Life
7.2 Battery Life
8 Safety Considerations
9 Proper Use and Handling
9.1 Care and Handling
9.2 Transportation
9.3 Waste Management: Recycling and Disposal
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Composition and Chemistry
3
A rechargeable battery is based on the principle that the charge/discharge process is reversible, that is, the
energy delivered by the battery during discharge can be replaced or restored by recharging.
3.1 Active Components: Positive and Negative Electrodes
Nickel oxyhydroxide (NiOOH) is the active mate-
rial in the positive electrode of the nickel-metal hydride
battery in the charged state, the same as in the nickel-
cadmium battery.
The negative active material, in the charged state,
is hydrogen in the form of a metal hydride. This metal
alloy is capable of undergoing a reversible hydrogen
absorbing/desorbing reaction as the battery is charged
and discharged, respectively.
and AB2 alloys, of which TiMn2 or ZrMn2 are examples.
DURACELL nickel-metal hydride battery technol-
ogy is based on the use of AB5 instead of AB2 alloys.
AB5 alloys offer better corrosion resistance characteris-
tics, resulting in longer cycle life and better recharge-
ability following storage. The composition of the metal
alloy is formulated for optimal stability over a large
number of charge/discharge cycles. Other important
properties of the alloy include:
The unique attribute of the hydrogen storage
alloy is its ability to store hundreds of times its own
volume of hydrogen gas at a pressure less than atmos-
pheric pressure. Many different intermetallic com-
pounds have been evaluated as electrode materials for
nickel-metal hydride batteries. Typically, these fall into
two classes: AB5 alloys, of which LaNi5 is an example,
Large hydrogen storage capability for high energy
density and battery capacity.
Favorable kinetic properties for high rate capability
during charge and discharge.
Low hydrogen pressure alloy and high purity mate-
rials to minimize self-discharge.
•
•
•
3.2 Electrolyte
An aqueous solution of potassium hydroxide is
the major component of the electrolyte of a nickel-
metal hydride battery. A minimum amount of elec-
trolyte is used in this sealed cell design, with most of
this liquid being absorbed by the separator and the
electrodes. This “starved electrolyte” design facilitates
the diffusion of oxygen to the negative electrode at the
end-of-charge for the “oxygen recombination” reaction.
3.3 Cell Reactions
During discharge, the nickel oxyhydroxide is
reduced to nickel hydroxide
The overall reaction on discharge is:
MH + NiOOH ——> M + Ni(OH)2
The process is reversed during charge.
-
-
NiOOH + H2O + e ——> Ni(OH)2 + OH
and the metal hydride (MH) is oxidized to the metal
alloy (M).
-
-
MH + OH ——> M + H2O + e
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Composition and Chemistry (cont.)
The sealed nickel-metal hydride cell uses the
“oxygen-recombination” mechanism to prevent a build-
up of pressure that may result from the generation of
oxygen towards the end of charge and overcharge.
This mechanism requires the use of a negative electrode
(the metal hydride/metal electrode) which has a higher
effective capacity than the positive (nickel oxyhydrox-
ide/nickel hydroxide electrode) electrode. A schematic
drawing of the electrodes is shown in Figure 3.3.1.
During charge, the positive electrode reaches
FIGURE 3.3.1
Positive Electrode
NiOOH/Ni(OH)2
Useful Capacity
MH/Alloy
full charge before the negative electrode which causes
the evolution of oxygen to begin:
Charge
Reserve
Discharge
Reserve
Negative Electrode
Schematic representation of the electrodes, divided
into useful capacity, charge reserve and discharge
reserve.
-
> H2O + 12 O2 + 2e
- _____
2OH
The oxygen gas diffuses through the separator
to the negative electrode, a process which is facilitated
by the “starved-electrolyte” design and the selection of
an appropriate separator system.
At the negative electrode, the oxygen reacts
with the metal hydride and oxidizes or discharges the
metal hydride to produce water:
_____
> 2M + H2O
2MH + 12 O2
Thus, the negative electrode does not become fully
charged and pressure does not build up.
The charge current, however, must be con-
trolled at the end of charge and during overcharge to
limit the generation of oxygen to below the rate of
recombination. Thus, charge control is required to pre-
vent the build-up of gases and pressure. Duracell rec-
ommends that continuous overcharge not exceed C/300
for optimal performance.
As shown in Figure 3.3.1, the nickel-metal
hydride cell is designed with a discharge and charge
reserve in the negative electrode. The discharge
reserve minimizes gassing and degradation of the cell in
the event of overdischarge. The charge reserve ensures
that the cell maintains low internal pressure on over-
charge.
The negative electrode has excess capacity
compared to the positive electrode and is used to
handle both overcharge and overdischarge. Thus,
the useful capacity of the battery is determined by
the positive electrode.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Battery Construction
4
DURACELL standard-sized nickel-metal hydride batteries are constructed with cylindrical and prismatic nickel-
metal hydride cells. DURACELL nickel-metal hydride batteries are a sealed construction designed for optimal perfor-
mance and maximum safety. The batteries are manufactured to strict quality control standards to ensure reliability
and consumer satisfaction and offer such features as:
High energy density — Minimizes battery volume
and weight
Durability — Manufactured with LEXAN® and
LUSTRAN® polycarbonate high impact and flame
retardant polymers
•
•
•
•
Wide voltage range — Meets operating voltage
requirements of 3C devices
UL listing — Independent approval of battery use
in devices
Thin profiles — Innovative wall-less design
•
•
Advanced interconnect — Self securing, voltage-
keyed interconnect provides a highly reliable battery-
to-device contact
®
LEXAN is a registered trademark of the General Electric Company.
®
LUSTRAN is a registered trademark of the Monsanto Company.
4.1 Basic Cell Construction
The electrodes in both cylindrical and prismatic
nickel-metal hydride cell is a highly porous nickel-felt
substrate into whichthe nickel compounds are pasted.
Similarly, the negative electrode is a perforated nickel-
plated steel foil onto which the plastic-bonded, active
hydrogen storage alloy is coated.
cell configurations are designed with highly porous
structures which have large surface areas to provide low
internal resistance which results in superior high rate
performance. The positive electrode in the cylindrical
4.2 Cylindrical Cell Construction
The assembly of a cylindrical cell is shown in
top assembly to the can. The top assembly incorporates
Figure 4.2.1. The electrodes are separated by the sepa- a resealable safety vent, a metal lid and a plastic gasket.
rator which is a synthetic, non-woven material that A heat-shrink tube is placed over the metal can. The
serves as an insulator between the two electrodes and as bottom of the metal can serves as the negative terminal
a medium for absorbing the electrolyte. The electrodes
are spirally-wound and inserted into a cylindrical nickel-
plated steel can. The electrolyte is added and contained
within the pores of the electrodes and separator.
The positive electrode is connected to the metal
and the metal lid as the positive terminal. The insulator
and gasket insulate the terminals from each other. The
vent provides additional safety by releasing any excess
pressure that may build up if the battery is subjected to
abusive conditions.
lid with a tab. The cell is then sealed by crimping the
Metal Can
Separator
FIGURE 4.2.1
Negative Electrode
Heat Shrink Tube
Positive Electrode
(-) Negative Terminal
Insulator
Positive Tab
Metal Lid
Cosmetic Disk
Gasket
Safety Vent
(+) Positive Terminal
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Battery Construction (cont.)
4.3 Prismatic Cell Construction
FIGURE 4.3.1
The basic differences between the prismatic
c
ell and the cylindrical cell are the construction of
(+) Positive Terminal
Safety Vent
the electrodes and the shape of the can. Prismatic
cells are designed to meet the needs of compact
equipment where space for the battery is limited.
The rectangular shape of the prismatic cell permits
more efficient battery assembly by eliminating the
voids that occur in a battery constructed with
cylindrical cells. Thus, the volumetric energy density
of a battery can be increased by constructing it with
prismatic instead of cylindrical cells.
Heat Shrink Tube
Metal Lid
Cosmetic
Disk
Gasket
Insulator
Positive Tab
Figure 4.3.1 shows the structure of the pris-
matic nickel-metal hydride cell. The electrodes are
manufactured in a manner similar to those of the
cylindrical cell, except that the finished electrodes are
flat and rectangular in shape. The positive and
negative electrodes are interspaced by separator
sheets. The assembly is then placed in a nickel-plated
steel can and the electrolyte is added. The positive
electrodes are connected to the metal lid with a tab.
The cell is then sealed by crimping the top assembly to
the can. The top assembly incorporates a resealable
safety vent, a metal lid and a plastic gasket that is
similar to the one used in the cylindrical cell. A heat-
shrink tube is placed over the metal can. The bottom
of the metal can serves as the negative terminal and
the top metal lid as the positive terminal. The insula-
tor and gasket insulate the terminals from each
other. The vent provides additional safety by re-
leasing any excess pressure that may build up if the
battery is subjected to abusive conditions.
Positive Electrode
Separator
Negative Electrode
(-) Negative Terminal
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Performance Characteristics
5
FIGURE 5.2.1
5.1 General Characteristics
8.5
Temperature: 45°C (113°F)
The discharge characteristics of the nickel-metal
8.0
hydride cell are very similar to those of the nickel-
cadmium cell. The charged open circuit voltage of both
systems ranges from 1.25 to 1.35 volts per cell. On
discharge, the nominal voltage is 1.2 volts per cell and
the typical end voltage is 1.0 volt per cell.
7.5
C/5 (0.48A)
C (2.4A)
7.0
otlage(V)
6.5
6.0
5.5
Figure 5.1.1 illustrates the discharge character-
istics of nickel-metal hydride and nickel-cadmium
rechargeable cells of the same size. As shown, the volt-
age profile of both types of cells is flat throughout most
of the discharge. The midpoint voltage can range from
1.25 to 1.1 volts per cell, depending on the discharge
load. Figure 5.1.1 can also be used to compare the
capacity of the two rechargeable types. Note that the
capacity of the nickel-metal hydride cell is typically up to
40 percent higher than that of a nickel-cadmium cell of
equivalent size.
0
0.5
1.0
1.5
2.0
2.5
Discharge Capacity (Ah)
FIGURE 5.2.2
8.5
Temperature: 21°C (70°F)
8.0
7.5
7.0
6.5
6.0
C/5 (0.48A)
C (2.4A)
FIGURE 5.1.1
otlage(V)
1.5
1.4
1.3
5.5
0
1.2
0.5
1.0
1.5
2.0
2.5
C/5
Discharge Capacity (Ah)
C/5
80
1.1
oltage(V)
1.0
.9
FIGURE 5.2.3
Ni-Cd
100
Ni-MH
140 160
0
20
40
60
120
8.5
Temperature: -20°C (-4°F)
Temperature: 0°C (32°F)
Ampere-Hour Capacity (%)
8.0
7.5
7.0
6.5
6.0
Comparison of discharge voltage and capacity of
same-size Ni-MH and Ni-Cd cells.
C/5 (0.48A)
[Conditions: Charge: C/3 for 5 hours, Temperature: 21°C (70°F)]
C/5 (0.48A)
C (2.4A)
C (2.4A)
otlage(V)
5.2 Discharge Characteristics: Effect of
Discharge Rate and Temperature
5.5
0
0.5
1.0
1.5
2.0
2.5
Typical discharge curves for DURACELL nickel-
metal hydride batteries under constant current loads at
various temperatures are shown in Figures 5.2.1 to
5.2.3. Discharge voltage is dependent on discharge
current and discharge temperature.
Discharge Capacity (Ah)
Voltage and capacity of DURACELL DR30 Ni-MH
batteries at various discharge temperatures
and rates.
[Conditions: Charge: 1C to -∆V = 60mV @ 21°C (70°F)]
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Performance Characteristics (cont.)
Typically, when the current is higher and the
temperature is lower, the operating voltage will be
lower. This is due to the higher “IR” drop that
occurs with increasing current and the cell’s increas-
ing resistance at the lower temperatures. However,
at moderate discharge rates (≈C/5), the effect of
low temperature on the capacity of the nickel-metal
hydride battery is minimal.
FIGURE 5.3.1
2.5
21°C (70°F)
45°C (113°F)
2.0
0°C (32°F)
1.5
5.3 Capacity: Effect of Discharge Rate
and Temperature
pcaity(Ah)
1.0
0.5
0
C
-20°C (-4°F)
The ampere-hour capacity of the battery is
dependent on the discharge current and temperature,
as can be observed in Figure 5.3.1. It should be noted
that the delivered capacity is dependent on the cutoff
or end voltage. The delivered capacity can be increased
by continuing the discharge to lower end voltages.
However, the battery should not be discharged to too
low a cut-off voltage (less than 0.9 volts per cell) as
the cells may be damaged (see Section 5.6). The
recommended cutoff voltage for nickel-metal hydride
batteries is 1.0 volt per cell.
C (2.4)
C/5 (0.48)
2C (4.8)
Discharge Rate (A)
Typical capacity of DURACELL DR30 batteries under
constant current discharges at various temperatures.
[Conditions: Charge: 1C to -∆V = 60mV @ 21°C (70°F); Discharge
to 6.0V]
Typically, optimum performance of the nickel-
metal hydride battery is obtained between 0°C and 45°C
(32°F and 113°F). The performance characteristics of
the battery are affected moderately at higher tempera-
tures. At lower discharge temperatures, performance
decreases more significantly, caused primarily by the
increase in internal resistance. Similarly, the effects of
temperature on performance are more pronounced at
higher discharge rates. The capacity of the battery
decreases more noticeably as the current increases,
particularly at lower temperatures.
5.4 Energy Density
Energy density is the ratio of the energy available
from a battery to its volume or weight. A comparison of
the performance of various battery systems is normally
made on practical, delivered energy density per-unit-
weight or volume using production-based batteries and
performance as opposed to theoretical energy density.
Comparing energy densities, one must consider the
influence of cell size, internal design, discharge rate and
temperature conditions, as these parameters strongly
impact performance characteristics.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Performance Characteristics (cont.)
Figure 5.4.1 compares the gravimetric and
volumetric energy density of nickel-metal hydride
and nickel-cadmium cells. As indicated, nickel-metal
hydride cells deliver more energy per weight or
volume than nickel-cadmium cells.
FIGURE 5.4.1
200
Wh/L
150
Wh/L
100
5.5 Constant Power Discharge Characteristics
The output energy characteristic of nickel-metal
hydride batteries under the constant power mode at
different power levels is shown in Figure 5.5.1.
As illustrated, the energy delivered does not vary
significantly with increasing power. The power levels
are shown on the basis of E-Rate. The E-Rate is
calculated in a manner similar to calculating the C-Rate.
For example, at the E/10 power level, the power
for a battery rated at 17.3 watt-hours is 1.73 watts.
Wh/kg
50
0
Wh/kg
Ni-Cd
Ni-MH
Gravimetric and volumetric energy density of Ni-Cd
and Ni-MH cells.
FIGURE 5.5.1
20
15
10
5
5.6 Polarity Reversal During Overdischarge
When cells are connected in series, the cell
with the lowest capacity will reach a lower point of
discharge than the others. The more cells that are
connected in series, the greater the possibility of a cell
being fully discharged and driven into overdischarge
and polarity reversal. During reversal, hydrogen gas
evolves from the positive electrode. Hydrogen gas
will be reabsorbed by the negative electrode and
eventually oxygen gas will evolve from the negative
electrode. Extended overdischarge will lead to elevated
cell pressure and opening of the safety vent within
the nickel-metal hydride cells.
Eenrgy(Wh)
0
E/10 (1.7)
E/3 (5.8)
E (17.3)
Power (W)
Typical energy of DURACELL DR30 batteries under
constant power discharges.
[Conditions: Charge: 1C to -∆V = 60mV; Discharge to 6.0V;
Temperature: 21°C (70°F)]
To minimize the occurrence of polarity reversal,
the cells in DURACELL rechargeable batteries have
capacities that are “matched” to each other. Device
designers can help prevent overdischarge by designing a
cutoff voltage for device operation of 1.0 volt per cell.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Performance Characteristics (cont.)
5.7 Internal Impedance
FIGURE 5.7.1
180
DURACELL nickel-metal hydride batteries have low
internal impedance because they are manufactured using
cells designed with thin plate electrodes which offer large
surface areas and good conductivity. Figure 5.7.1 shows
the change in internal impedance with depth of discharge.
As demonstrated, the impedance remains relatively constant
during most of the discharge. Towards the end of the dis-
charge, the impedance increases due to the conversion of
the active materials to a non-conductive form.
)
175
DR30
170
tlrIpdance(m
165
0
20
40
60
80
100
Discharge Capacity (%)
5.8 Self-Discharge and Charge Retention
Internal impedance of DURACELL DR30 Ni-MH
batteries at various discharge capacities.
[Conditions: Charge: C/5 for 7.5 hours; Discharge: C/5;
Temperature: 21°C (70°F); Measurements at 1000 Hz]
The state-of-charge and capacity of the nickel-
metal hydride battery decrease during storage due to
self-discharge of the cells. Self-discharge results from
the reaction of residual hydrogen in the battery with the
positive electrode, as well as the slow and reversible
decomposition of the positive electrode. The rate of
self-discharge is dependent upon the length of time and
temperature at which the battery is stored — the high-
er the temperature, the greater the rate of self-dis-
charge. As illustrated in Figure 5.8.1, cells stored at
0°C (32°F) retain more of their capacity than those
stored at 20°C and 45°C (68°F and 113°F), particularly
after 30 days.
FIGURE 5.8.1
0°C (32°F)
100
80
60
40
20°C (68°F)
45°C (113°F)
Generally, long term storage of a nickel-metal
hydride battery in either a charged or discharged condi-
tion has no permanent effect on capacity. Capacity loss
due to self-discharge is reversible and nickel-metal
hydride batteries can recover to full capacity by proper
recharging. For example, full capacity of a nickel-metal
hydride battery that was stored at room temperature
for up to one year can be restored by cycling through
repeated charge/discharge cycles.
RsedulCpacity(%)
20
0
0
5
10
15
20
25
30
Storage Time (Days)
Self-discharge characteristic of Ni-MH cells at
various temperatures.
[Conditions: Charge: C/3 for 5 hours; Discharge: C/5 to 1.0V;
Temperature: 21°C (70°F)]
As with operation at elevated temperatures,
however, long term storage at high temperatures can
lead to deterioration of seals and separators and should
be avoided. The recommended temperature range for
long term storage of nickel-metal hydride batteries is
10°C to 30°C (50°F to 86°F).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Performance Characteristics (cont.)
5.9 Voltage Depression (“Memory Effect”)
FIGURE 5.9.1
Although many years of premium performance
can be enjoyed from a nickel-metal hydride battery that
is properly handled, the capacity delivered in each
charge/discharge cycle will eventually begin to decrease.
This inevitable decrease in capacity can be accelerated by
overcharging, storage or usage at high temperatures, or
through poor matching of cells within a pack. Often,
battery users who experience short service life have
incorrectly attributed capacity loss to a phenomenon
called “memory effect.”
1.35
1.25
1.15
1.05
Cycle #2
otlage(V)
Cycle #1
Cycle #21
Cycle #20
0.95
0.85
Cycle #18
Cycle #19
0
0.25
0.5
Time (Hours)
Effects on Ni-MH cell capacity due to repetitive partial
0.75
1.0
The term memory effect is used synony-
mously with the term “voltage depression.” Voltage
depression is a scientifically measurable characteristic of
all batteries, however, nickel-cadmium batteries demon-
strate particularly acute sensitivity. A properly designed
application with nickel-metal hydride batteries will result
in neither permanent performance loss nor perceivable
temporary capacity decreases from this characteristic.
A reversible drop in voltage and loss of capacity
may occur when a nickel-metal hydride battery is par-
tially discharged and recharged repetitively without the
benefit of a full discharge, as illustrated in Figure 5.9.1.
After an initial full discharge (Cycle #1) and charge, the
cell is partially discharged to 1.15 volts and recharged
for a number of cycles. During this cycling, the dis-
charge voltage and capacity drop gradually in very small
increments (Cycles #2 to #18). On a subsequent full
discharge (Cycle #19), the discharge voltage is
depressed compared to the original full discharge
(Cycle #1).
discharges
.
[Conditions: Charge: (Cycle #1– #21) = 1C to -∆V = 12mV. Discharge: Cycle #1 = 1C
to 1.0 V, (Cycle #2– #18) = 1C to 1.15V, (Cycle #19 – #21) = 1C to 1.0V; Temperature:
21°C (70°F)]
physical characteristics and increase in resistance.
Subsequent full discharge/charge cycling will restore the
active materials to their original state.
The extent of voltage depression and capacity
loss depends on depth of discharge and can be avoided by
discharging the battery to an appropriate cutoff
voltage. Voltage depression is most apparent when the
discharge is terminated at higher cutoff voltages, such as
1.2 volts per cell. A smaller voltage depression and
capacity loss occurs if the discharge is cut off between
1.15 volts to 1.10 volts per cell. Discharging to 1.0
volts per cell should not result in significant voltage
depression or capacity loss during subsequent discharges.
A device properly designed with nickel-metal
Because the cell appears to “remember” the
lower capacity, this voltage depression phenomenon is
often referred to as memory effect. However, the cell
can be quickly restored to full capacity with a few full
discharge/charge cycles, as indicated in Cycles #20
and #21.
The voltage drop occurs because only a portion
of the active materials in the cell is discharged and
recharged during shallow or partial discharging. The
active materials that have not been cycled change in
hydride batteries will minimize the effects of voltage
depression and capacity loss. The voltage depression
and capacity loss in DURACELL nickel-metal hydride
batteries is only a small fraction (less than 5 percent
in worst cases) of the battery’s capacity and most users
will never experience a perceptible performance loss.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Charging Sealed Nickel-Metal Hydride Batteries
6
•
•
•
6.1 General Principles
FIGURE 6.1.1
2.0
Recharging is the process of replacing energy
Ni-Cd
that has been discharged from the battery. The subse-
quent performance of the battery, as well as its overall
life, is dependent on effective charging. The main crite-
ria for effective charging are:
1.8
1.6
Ni-MH
1.4
oatg/Cel(V)
1.2
1.0
Choosing the appropriate rate
0
20
40
60
80
100
120
Limiting the temperature
Charge Input (% of Typical Capacity)
Selecting the appropriate termination technique
Typical charge voltage characteristics of Ni-MH and
Ni-Cd batteries.
[Conditions: Charge: 1C @ 21°C (70°F) to -∆V = 10mV/cell]
The recharging characteristics of nickel-metal
hydride batteries are generally similar to those of
nickel-cadmium batteries. There are some distinct
differences, however, particularly on the requirements
for charge control because the nickel-metal hydride
battery is more sensitive to overcharging. Caution
should be exercised before using a nickel-cadmium
battery charger interchangeably for both battery types
because it may not optimally charge a nickel-metal
hydride battery, particularly on high rate chargers.
The most common charging method for the
nickel-metal hydride battery is a constant current
charge with the current limited in order to avoid an
excessive rise in temperature. Limiting the charge
current also reduces the risk of exceeding the rate of
the oxygen recombination reaction to prevent cell
venting.
FIGURE 6.1.2
Temperature (°F)
131
122
55
50
45
40
35
30
25
20
15
113
104
Ni-MH
C)
95
Ni-Cd
86
77
68
59
Tpmature(
0
20
40
60
80
100
120
Charge Input (% of Typical Capacity)
Typical charge temperature characteristics of Ni-MH
and Ni-Cd batteries.
[Conditions: Charge: 1C @ 21°C (70°F) to -∆V = 10mV/cell]
Figure 6.1.1 compares the voltage profiles of
nickel-metal hydride and nickel-cadmium batteries dur-
ing charge at a constant current rate. The voltages of
both systems rise as the batteries accept the charge. As
the batteries approach 75 to 80 percent charge, the
voltages of both battery types rise more sharply due to
the generation of oxygen at the positive electrode.
However, as the batteries go into overcharge, the volt-
age profile of the nickel-metal hydride battery does not
exhibit as prominent a voltage drop as the nickel-
cadmium battery.
In Figure 6.1.2, the temperature profiles of the
nickel-metal hydride and nickel-cadmium batteries are
compared during charge at a constant current charge
rate. Throughout the first 80 percent of charge, the
temperature of the nickel-cadmium battery rises gradu-
ally because its charge reaction is endothermic (absorbs
heat). The temperature of the nickel-metal hydride
battery, on the other hand, rises quickly because its
charge reaction is exothermic (releases heat). After
80 to 85 percent of charge, the temperature of both
battery types also rises due to the exothermic oxygen
recombination reaction, causing the voltage to drop as
the batteries reach full charge and go into overcharge.
Both the voltage drop after peaking (-∆V) and
the temperature rise are used as methods to terminate
the charge. Thus, while similar charge techniques can
be used for nickel-metal hydride and nickel-cadmium
batteries, the conditions to terminate the charge may
differ because of the varying behavior of the two bat-
tery systems during charge. To properly terminate
charging of DURACELL nickel-metal hydride batteries,
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Charging Sealed Nickel-Metal Hydride Batteries (cont.)
Duracell recommends the charge termination method
described in Section 6.3.1.
FIGURE 6.1.3
10.0
The voltage of the nickel-metal hydride battery
during charge depends on a number of conditions,
including charge current and temperature. Figures
6.1.3 and 6.1.4 show the voltage profile of the nickel-
metal hydride battery at different ambient temperatures
and charge rates, respectively. The battery voltage rises
with an increase in charge current due to an increase in
the “IR” drop and overpotential during the electrode
reaction. The battery voltage decreases with increasing
temperature as the internal resistance and overpotential
during the electrode reaction decrease.
9.5
9.0
8.5
8.0
7.5
0°C (32° F)
21°C (70° F)
otlage(V)
0
0.2
0.4
0.6
0.8
1.0
1.2
A rise in temperature and pressure at high
Charge Time (Hours)
charge rates occurs and underscores the need for prop-
er charge control and effective charge termination
when “fast charging.” Excessive pressure and tempera-
ture increases can result in activation of cell vents or
battery safety electronics, as described in Section 6.4.
Temperature also affects charge efficiency.
Charge voltage of DURACELL DR30 Ni-MH batteries
at various temperatures.
[Conditions: Discharge: C/5 to 6.0V @ 21°C (70°F); Charge: 1C to -∆V =
60mV]
FIGURE 6.1.4
Charge efficiency decreases at higher temperatures due
to the increasing evolution of oxygen at the positive
electrode. Thus, charging at high temperatures results
in lower capacity. At lower temperatures, charge effi-
ciency is high due to decreasing oxygen evolution.
However, oxygen recombination is slower at lower tem-
peratures and a rise in internal cell pressure may occur
depending on the charge rate.
10.0
9.5
9.0
8.5
8.0
7.5
7.0
C (2.4A)
C/5 (0.48A)
otlage(V)
Proper charging is critical not only to obtain
maximum capacity on subsequent discharges but also
to avoid high internal temperatures, excessive over-
charge and other conditions which could adversely
affect battery life.
0
1.0
2.0
3.0
4.0
Charge Capacity (Ah)
Charge voltage of DURACELL DR30 Ni-MH batteries
at various rates.
[Conditions: Discharge: C/5 to 6.0V; Charge: 1C to -∆V = 60mV, C/5 to
7.5 hrs.; Temperature: 21°C (70°F)]
6.2 Techniques for Charge Control
The characteristics of the nickel-metal hydride
battery define the need for proper charge control in
order to terminate the charge and prevent overcharging
or exposure to high temperatures. Each charge control
technique has its advantages and disadvantages. For
example, higher capacity levels are achieved with a 150
percent charge input, but at the expense of cycle life;
long cycle life is attained with a 105 to 110 percent
charge input, albeit with slightly lower capacity due to
less charge input. Thermal cutoff charge control may
reduce cycle life because higher temperatures are
reached during the charge; however, it is useful as a
backup control in the event that the primary termina-
tion method is not effective during charge.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Charging Sealed Nickel-Metal Hydride Batteries (cont.)
The following summary explains some of the
recommended methods for charge control. The charac-
teristics of each of these methods are illustrated in
Figure 6.2.1. In many cases, several methods are
employed, particularly for high rate charging.
FIGURE 6.2.1
-∆V
Voltage (V)
TCO
)
6.2.1 Timed Charge
(
Under the timed charge control method, the
charge is terminated after the battery is charged for a
predetermined length of time. This method should be
used only for charging at low rates (less than C/3) to
avoid excessive overcharge because the state-of-charge
of the battery, prior to charging, cannot always be
determined. If a timed charge termination is used, a
time of 120 percent charge input is recommended with
a backup temperature cutoff of 60°C (140°F).
otlage(V)
Temperature (T)
mpature(T)
dT/dt
TmpuDfrential
Temperature Differential Output (dT/dt)
Charge Time (t)
Charge characteristics of Ni-MH batteries using
various charge termination methods.
must be sensitive enough to terminate the charge
when the voltage drops, but not so sensitive that it
will terminate prematurely due to noise or other
normal voltage fluctuations. A charge rate of 1C and
a 5 to 10 millivolt per cell drop is recommended for
the nickel-metal hydride battery with a backup tem-
perature cutoff of 60°C (140°F). A top-up charge is
not necessary with this charge termination method.
Voltage drop is widely used with nickel-cadmi-
um batteries. With this technique, the voltage during
charge is monitored and the charge is terminated
when the voltage begins to decrease. This approach
can be used with nickel-metal hydride batteries, but
as noted in Section 6.1, the voltage drop of the nickel-
metal hydride battery is not as prominent as that of
the nickel-cadmium battery and may be absent in
charge currents below the C/3 rate, particularly at
elevated temperatures. The voltage sensing circuitry
6.2. 3 Voltage Plateau (Zero ∆V)
Since the nickel-metal hydride battery does
not always show an adequate voltage drop, an alter-
nate method used is to terminate the charge when
the voltage peaks and the slope is zero, rather than
waiting for the voltage to drop. The risk of over-
charge is reduced as compared to the -∆V method.
If this method is employed, a charge rate of 1C and a
backup temperature cutoff of 60°C (140°F) is recom-
mended. A top-up charge can follow to ensure a full
charge. Duracell does not recommend this termina-
tion method because of the risk of premature cutoff.
6.2. 4 Temperature Cutoff
Another technique for charge control is to
monitor the temperature rise of the battery and ter-
minate the charge when the battery has reached a
temperature which indicates the beginning of over-
charge. It is difficult, however, to precisely determine
this point because it is influenced by ambient tempera-
ture, cell and battery design, charge rate, and other
factors. A cold battery, for instance, may be over-
charged before reaching the cutoff temperature, while
a warm battery may be undercharged.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Charging Sealed Nickel-Metal Hydride Batteries (cont.)
6.2.4 Temperature Cutoff (cont.)
Usually this method is used in conjunction with
other charge control techniques primarily to terminate
the charge in the event that the battery reaches exces-
sive temperatures before the other charge controls
activate. A charge rate of 1C and a temperature cutoff
at 60°C (140°F) is recommended. A top-up charge is
not recommended if this termination method is used.
6.2.5 Delta Temperature Cutoff (∆TCO)
This technique measures the battery tempera-
ture rise above the starting temperature during charging
and terminates the charge when this rise exceeds a pre-
determined value. In this way, the influence of ambient
temperature is minimized. The cutoff value is depen-
dent on several factors, including cell size, configuration
and number of cells in the battery, and the heat capacity
of the battery. Therefore, the cutoff value should be
determined for each type of battery. This value will
be greater for nickel-metal hydride batteries than for
nickel-cadmium batteries. A charge rate of 1C and a
temperature change of 15°C (27°F) with a backup
temperature cutoff of 60°C (140°F) is recommended
for ∆TCO charge termination. A top-up charge is not
necessary with this termination method.
6.2.6 Rate of Temperature Increase (dT/dt)
FIGURE 6.2.2
In this method, the change in temperature with
time is monitored and the charge is terminated when a
predetermined rate of temperature rise is reached. The
influence of ambient temperature is reduced. A dT/dt cut-
off is a preferred charge control method for nickel-metal
hydride batteries because it provides long cycle life.
Figure 6.2.2 shows the advantage of using a dT/dt
method compared to -∆V in terminating a fast charge.
The dT/dt method senses the start of the overcharge
earlier than the -∆V method. The battery is exposed to
less overcharge and overheating, resulting in less loss of
cycle life. A charge rate of 1C and a temperature increase
of 1°C (1.8°F) per minute with a back-up temperature cut-
off of 60°C (140°F) is recommended for dT/dt. A top-up
charge of C/10 for 1/2 hour is also recommended.
3.0
2.5
-∆V= 60mV
dT/dt = 1°C(1.8°F)/min
2.0
1.5
DrsgeCpacity(Ah)
1.0
0
100
200
300
400
500
Cycle Number
Cycle life and capacity of DURACELL DR30 Ni-MH
batteries as a function of charge termination.
[Conditions: Charge: 1C; Discharge: C/5 to 6.0V; Cycled to 70% of
initial capacity; Temperature: 21°C (70°F)]
6.3 Charging Methods
Nickel-metal hydride batteries can be charged
employing the same methods used for charging nickel-cad-
mium batteries. However, the charge termination tech-
nique may differ because of the varying behavior of the
two battery systems. For proper charging of nickel-metal
hydride batteries, the charge termination technique used
should be appropriate for the particular charge rate. The
charge rate and appropriate termination technique is sum-
marized in Table 6.3.1.
Sections 6.3.1 to 6.3.5. In order to optimize performance,
Duracell recommends a three-step charge procedure.
Charge Rate
1C to C/2
Termination Technique
Voltage or temperature based
Voltage based
C/2 to C/3
C/3 to C/10
C/10 and below
Not recommended
Time limited
Some of the various methods used to properly
charge nickel-metal hydride batteries are explained in
Table 6.3.1 Recommended charge termination techniques
for particular charge rates.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Charging Sealed Nickel-Metal Hydride Batteries (cont.)
6.3.1 Duracell’s Recommendation: Three-Step Charge Procedure
For fast charging and optimum performance,
Duracell recommends a three-step procedure that pro-
vides a means of rapidly charging a nickel-metal hydride
battery to full charge without excessive overcharging or
exposure to high temperatures. The steps in sequential
order are:
1) Charge at the 1C rate, terminated by using
dT/dt = 1°C(1.8°F) /minute.
2) Apply a C/10 top-up charge, terminated by
a timer after 1/2 hour of charge.
3) Apply a maintenance charge of indefinite
duration at C/300 rate.
The three-step charging method should be used
with a backup temperature cutoff of 60°C (140°F).
6.3.2 Low-Rate Charge (≈12 hours)
Charging at a constant current at the C/10 rate
with time-limited charge termination is a convenient
method to fully charge nickel-metal hydride batteries.
At this current level, the generation of gas will not
exceed the oxygen recombination rate. The charge
should be terminated after 120 percent charge input,
or approximately 12 hours for a fully discharged bat-
tery. Excessive overcharging should be avoided, as it
can damage the battery.
The temperature range for this charge method
is 0°C to 45°C (32°F to 113°F), with optimum
performance being obtained between 15°C to 30°C
(59°F to 86°F).
6.3.3 Quick Charge (≈4 hours)
Nickel-metal hydride batteries can be efficiently
and safely charged at higher rates than described in
Section 6.3.2. Charge control is required in order to
terminate the charge when the rate of oxygen recombi-
nation is exceeded or the battery temperature rises
excessively. A fully discharged battery can be charged
at the C/3 rate terminated with a -∆V = 10 mV/cell. In
addition, a timer control set to a 120 percent charge
input (3.6 hours) and a temperature cutoff of 60°C
(140°F) should be used as a backup termination to
avoid exposing the battery to excessively high tempera-
tures. This charging method may be used in an ambient
temperature range of 10°C to 45°C (50°F to 113°F). A
top-up charge is not necessary if this termination method
is used.
At the C/3 rate, a dT/dt termination method
should not be used because the rate of temperature
increase may not be sufficient to terminate the charge.
6.3.4 Fast Charge (≈1 hour)
Another method of charging nickel-metal
hydride batteries in even less time is to charge at the
C/2 to 1C constant current rates. At these high charge
rates, it is essential that the charge be terminated early
during overcharge. However, timer control is inade-
quate, as the time needed for charge can not be pre-
dicted — a partially charged battery could easily be
overcharged while a fully discharged one could be
undercharged, depending on how the timer control
is set.
With fast charging, the decrease in voltage
(-∆V) and the increase in temperature (∆T) can be used
to terminate the charge. For better results, termination
of fast charge can be controlled by sensing the rate of
temperature increase (dT/dt). A temperature increase
of 1°C (1.8°F) per minute with a backup temperature
cutoff of 60°C (140°F) is recommended. A top-up
charge of C/10 for 30 minutes should follow to ensure
a full charge.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Charging Sealed Nickel-Metal Hydride Batteries (cont.)
6.3.5 Trickle Charge
A number of applications require the use of
batteries which are maintained in a fully-charged state.
This is accomplished by trickle charging at a rate that
will replace the loss in capacity due to self-discharge.
In these applications, a trickle charge at a C/300 rate is
recommended. The preferred temperature range for
trickle charging is between 10°C to 35°C (50°F to
95°F). Trickle charge may be used following any of the
previously discussed charging methods.
6.4 Thermal Devices
DURACELL nickel-metal hydride batteries con-
tain a temperature sensing device and thermal protec-
tive devices. Thermal protective devices terminate
charge/discharge in the event high temperatures are
reached. This protection is particularly important when
fast charging methods are used. The types of devices
used are:
4) Positive Temperature Coefficient (PTC)
Device: This is a resettable device whose
resistance rapidly increases at a predeter-
mined current, thereby reducing the current
in the battery to a low and acceptable level.
The PTC device will respond to high current
beyond design limits (e.g. a short circuit) and
acts like a fuse. Unlike a one-time fuse, the
PTC device will reset to its low resistance
state when the latching current is removed.
It will also respond to high temperatures
around the PTC device, in which case it
operates like a temperature cut-off (TCO)
device.
1) Negative Temperature Coefficient (NTC)
Thermistor: This device senses internal bat-
tery temperature and provides this informa-
tion by means of a calibrated resistance
value to an external control circuit. The
thermistor is attractive because the control
can be set, external to the battery, to meet
the particular conditions of the charge. This
device is used in dT/dt charge control.
The location of thermal devices in the battery
assembly is critical to ensure that they will respond prop-
erly as the temperature may not be uniform throughout
the battery. Thermal devices in DURACELL nickel-metal
hydride batteries are set so the cells are not exposed to
temperatures above 91°C (196°F). The inclusion of
thermal protective devices in DURACELL nickel-metal
hydride batteries helps ensure safe battery operation.
2) Thermostat: This bimetal thermal protec-
tive device operates at a fixed temperature
and is used to cut off the charge (or dis-
charge) when a pre-established internal bat-
tery temperature or current is reached.
These temperature cutoff (TCO) devices
reset automatically after the overtempera-
ture or overcurrent condition has decreased
below a reset threshold.
3) Thermal Fuse: This device is wired in series
with the cell stack and will open the circuit
when a predetermined temperature is
reached. Thermal fuses are included as a
protection against thermal runaway and are
normally set to open at approximately 91°C
(196°F). This device cannot be reset once
opened.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Cycle and Battery Life
7
7.1 Cycle Life
FIGURE 7.1.1
Temperature (°F)
The cycle life of nickel-metal hydride batteries
32
50
68
86
104
122
depends on the many conditions to which the battery
has been exposed, as is true for all types of recharge-
able batteries. These include such variables as:
100
90
80
70
60
Temperature during charge and discharge
Charge and discharge current
Depth of discharge
•
•
•
•
•
•
CcylLife(%)
50
40
Method of charge control
Exposure to overcharging and overdischarging
Storage conditions
30
20
10
Typically, under a C/5 charge/discharge at
normal ambient temperatures (20°C or 68°F), up to
500 cycles can be achieved with the battery delivering
at least 80 percent of its rated capacity. The gradual
decrease in capacity results from an increase in the bat-
tery’s internal resistance, caused by minor irreversible
changes in the structure of the electrodes, electrolyte
distribution and separator dry-out.
0
10
20
30
40
50
Temperature (°C)
Impact on cycle life from repeated charging and
discharging at various ambient temperatures.
[Conditions: Charge: C/4 for 3.2 hours; Discharge: C/4 for 2.4 hours;
Capacity measured every 50 cycles @ 21°C (70°F): Charge: C/3 for
5 hours; Discharge: 1C to 1.0V]
For optimum battery life and maximum cycle
life, nickel-metal hydride batteries should be operated at
or near room temperature (20°C or 68°F). Repeated
operation at extreme temperatures during charge and
discharge will adversely affect the performance of the
cells (and thus the battery), as shown graphically in
Figure 7.1.1. Operation at high temperatures, particu-
larly in the overcharged condition, can cause the cell to
vent, releasing gas and possibly electrolyte through the
safety vent. High temperatures will also hasten the
deterioration of the separator and other materials in the
cell. At temperatures below 0°C (32°F), the oxygen
recombination reaction slows down and the cell is more
sensitive to overcharging, thus gas pressure will build up
more rapidly.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Cycle and Battery Life (cont.)
Charge rate and amount of charge input during
overcharging are also important factors affecting cycle
life. If the battery is charged at a rate that exceeds the
oxygen recombination rate, oxygen that is generated
during overcharge will not react, causing a build up in
gas pressure and a rise in temperature which will have
damaging effects on battery and cycle life. Prompt use
of an effective charge termination method when
deleterious overcharge begins will lessen the effect
on cycle life.
Cycle life is also affected by the depth of dis-
charge. Depending upon the charge termination method,
up to 500 cycles can be obtained with the battery being
fully discharged on each cycle (100 percent depth of dis-
charge, or “DOD”). Considerably higher cycle life can be
obtained if the battery is cycled at shallower charge/
discharges.
7.2 Battery Life
The same factors that affect cycle life affect
overall battery life. Operation or storage at extreme
temperatures, overcharging, cell venting and abusive
use will reduce battery life. Operation and storage of
batteries at or about room temperature (20°C or 68°F)
will maximize battery life. Recommended and permissi-
ble temperature limits are shown in Table 7.2.1.
Table 7.2.1
Recommended
Permissible
Low Rate Charge
15°C to 30°C (59°F to 86°F)
0°C to 45°C (32°F to 113°F)
10°C to 45°C (50°F to 113°F)
10°C to 45°C (50°F to 113°F)
10°C to 35°C (50°F to 95°F)
- 20°C to 50°C (-4°F to 122°F)
- 20°C to 50°C (-4°F to 122°F)
- 20°C to 35°C (-4°F to 95°F)
Quick Charge
10°C to 30°C (50°F to 86°F)
Fast Charge
10°C to 30°C (50°F to 86°F)
10°C to 30°C (50°F to 86°F)
0°C to 40°C (32°F to 104°F)
10°C to 30°C (50°F to 86°F)
10°C to 30°C (50°F to 86°F)
Trickle Charge
Discharge
Storage, Short Term
Storage, Long Term
Table 7.2.1 Recommended and permissible temperature limits for operation and storage of DURACELL
nickel-metal hydride rechargeable batteries.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Safety Considerations
8
Duracell’s nickel-metal hydride batteries are designed to ensure maximum safety. Each cell includes a
resealable pressure relief mechanism (safety vent) to prevent excessive build-up of pressure in the cell in the event
it is overcharged excessively, exposed to extreme high temperatures, or otherwise abused. Duracell’s nickel-metal
hydride batteries contain protective devices, as discussed in Section 6.4, to prevent excessive heating during fast
charging, high rate discharging beyond design limits, or abusive use.
DURACELL nickel-metal hydride batteries have been tested by the Underwriters Laboratories in accordance
with UL Standard 2054 “Outline of Investigation for Household and Commercial Batteries.” Duracell successfully
met all of the test criteria. The tests required under this Standard and the results of the tests on DURACELL cells
and batteries are summarized in Table 8.0.1. These tests cover operational and abusive conditions to which
batteries may be exposed during their use.
DURACELL nickel-metal hydride cells and batteries that are listed by Underwriters Laboratories under
UL Standard 2054 are identified in File No. MH17905. Some DURACELL nickel-metal hydride batteries used in
computers are listed under UL Standard 1950 “Safety of Information Technology Equipment, including Electrical
Business Equipment,” and are identified in File No. E158164.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Safety Considerations (cont.)
Table 8.0.1
Test
Test Conditions
Test Results
Flat Plate Crush Test
Cell is crushed between
two flat surfaces.
No explosion, sparks, or flames.
Impact Test
A 20 lb. weight is dropped from
height of 2 feet on cell.
No explosion, sparks, or flames.
Short Circuit Test*
Sample is shorted until discharged.
Test conducted at 20°C and
60°C (68°F and 140°F).
No evidence of venting, leakage, bulging or
other visible changes on individual cells.
Maximum case temperature was
129°C (264°F). In batteries, safety devices
operated, protecting battery from external
short. Maximum battery case temperature
was within 5°C (41°F) of ambient.
Forced-Discharge Test
(Voltage Reversal)
The cell, after discharge,
is over-discharged for 1.5
times rated capacity.
No venting, leakage, fire or explosion on test
conducted at C/3 discharge rate.
Abnormal Charge
Test
Cell is charged for 2.5
times rated capacity.
No venting, leakage, fire or explosion on
test conducted at C/3 charge rate.
Abusive Overcharge
Test*
Sample is charged by
power supply up to
200 watts until sample
vents or explodes.
Individual cells vented. No explosion or fire.
Maximum temperature on cell case was
200°C(392°F). In batteries, safety devices caused
charging circuit to open periodically, protecting
battery as designed. Maximum battery case
temperature was within 25°C (77°F) of ambient.
Heat Test
The cell is heated in an oven to
150°C (302°F).
No damage to cells; no bulging, venting,
fire or explosion.
Fire Exposure Test*
Sample is heated by a burner
fueled with methane.
Cells and batteries vented without
exploding. No significant flaming or spark.
No projectiles.
Table 8.0.1 Results of DURACELL nickel-metal hydride cells and/or batteries tested under UL Standard 2054
test regimes.
*Note: These tests were conducted on both individual cells and batteries. Tests not marked with an asterisk were conducted on individual cells only,
as deemed adequate by UL to demonstrate safety of both cells and batteries.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Proper Use and Handling
9
Nickel-metal hydride batteries can give years of safe and reliable service if they are used in accordance with
recommended procedures and are not abused. The batteries can be used in any operating position. Other than
charging, the only maintenance that should be required is to keep them clean and dry both during use and storage.
As previously discussed, nickel-metal hydride batteries, as with all battery systems, should not be exposed to
extreme temperatures for any long period of time. They can be stored for many months in a charged or discharged
state without any detrimental effects. Storage and operation at normal room temperatures is preferred, but wider
temperatures can be safely tolerated as discussed in detail in this bulletin.
DURACELL nickel-metal hydride batteries are shipped in a partially charged state. Therefore, caution should
be exercised to avoid short-circuiting the battery during handling.
After storage or periods during which the battery has not been used, the battery should be charged, using
any of the methods discussed in this bulletin, before being placed in service. Extended overcharging or overheating
of the battery should always be avoided.
The care and handling procedures outlined in the following section should be carefully followed.
9.1 Care and Handling
Disassembly
Vented Battery Compartments
The battery should not be disassembled, opened
or shredded under any conditions — high short
circuit currents and fire could result. Nickel-
metal hydride cells contain an alkaline elec-
trolyte which can cause injury. In the event that
the electrolyte comes into contact with skin or
eyes, immediately flush with fresh water and
seek medical advice.
It is possible that cells may vent if the battery is
overcharged or otherwise abused. Nickel-metal
hydride cells release hydrogen gas during venting
which could form potentially explosive mixtures
with air. Caution should be exercised to prevent
the gas from collecting in the battery or equip-
ment. Exposure to a source of ignition and air-
tight device compartments should be avoided.
Handling
Severe Use Applications
DURACELL nickel-metal hydride batteries are
designed to withstand normal handling. They
should not be dropped or subjected to strong
mechanical shock.
Short-term use of nickel-metal hydride
batteries outside of specified ranges may be
possible. Please consult Duracell if such a
requirement exists.
High Temperatures/Fire
Never subject the battery to heat or dispose of it
in a fire — the battery can explode, leak or burn
if exposed to fire or very high temperatures. For
optimum life, batteries should be shielded from
or placed away from heat sources. See Section
7.2 which describes recommended temperatures
for use, operation and storage of nickel-metal
hydride batteries.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Ni-MH Rechargeable Batteries
Proper Use and Handling (cont.)
9.2 Transportation
Procedures for the transportation of batteries
are specified by the United States Department of
Transportation in the “Code of Federal Regulations,”
CFR49, entitled “Transportation.” Internationally, air
transportation is specified by the International Civil
Aviation Organization (ICAO) in their publication
“Technical Instructions for the Safe Transport of
Dangerous Goods By Air.”
The nickel-metal hydride battery supplied by
Duracell is recognized by the regulatory agencies as a
“dry battery.” As such, it is not subject to regulation
and can be shipped in normal packaging and transported
on any mode of transportation without special
handling.
9.3 Waste Management: Recycling and Disposal
The management of waste products in the
United States is regulated by the U.S. Environmental
Protection Agency (EPA). The EPA Regulations are
listed in the “Code of Federal Regulations”, CFR40,
entitled “Protection of Environment.” Individual states
and local communities also may establish regulations
covering the disposal of waste products. These may be
more stringent than the federal regulations and cover
the management of household waste, which is not
included in the federal regulations.
B) Disposal:
Household Use – Individual batteries can be dis-
posed of with other household wastes.
Commercial Use – When ten or more batteries are
accumulated, the commercial user may want to con-
sider disposing the batteries in a secure waste land-
fill. Since these batteries are not classified as a
“hazardous waste,” they can be shipped to the
secure waste facility as “non-hazardous waste.”
The U.S. EPA has not provided any specific
regulations or guidelines for the waste management of
sealed nickel-metal hydride cells or batteries. As a
result, a number of states and local governments have
passed or are considering legislation which may require
special procedures for the disposal of these batteries.
Thus, state and local agencies should be contacted for
their waste management guidelines. Internationally,
procedures for waste management may vary from
country to country.
Local regulations, which specify other methods
for the disposal of nickel-metal hydride batteries,
supersede these recommendations. Waste manage-
ment companies can provide assistance for the disposal
of these batteries. As previously stated, nickel-metal
hydride batteries should not be disassembled, opened
or shredded.
In the absence of regulations or guidelines, the
following is recommended for recycling and disposing
of used nickel-metal hydride batteries:
A) Recycling;
Duracell encourages the recycling of DURACELL
nickel-metal hydride batteries and offers a special
worldwide recycling program. For information on
recycling DURACELL nickel-metal hydride rechargeable
batteries, please contact your nearest Duracell office.
In North America, call toll-free 1-800-551-2355
(9:00 a.m. to 5:00 p.m. E.S.T.).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
|