DBTV2500
SERVICE MANUAL
COLOR TELEVISION RECEIVER
ORIGINAL
MFR’S VERSION B
Design and specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
Change of IC101
DIFFERENCES
MFR'S VERSION B
DESCRIPTION
MFR'S VERSION D
DESCRIPTION
PART NO.
PART NO.
I56F07045A IC
A3I058G01B MAIN PCB ASS'Y
REF. NO.
IC101
I56F07044A IC
OEC7044A
TMX456A
OEC7045A
TMX456A
PCB010 A3I058G01A MAIN PCB ASS'Y
SPEC.NO. M3I0-62G
O/R NO. A073521
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES
6. AVOID AN X-RAY
As for the places which need special attentions,
they are indicated with the labels or seals on the
cabinet, chassis and parts. Make sure to keep the
indications and notices in the operation manual.
Safety is secured against an X-ray by consider-
ing about the cathode-ray tube and the high
voltage peripheral circuit, etc.
Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts and
make sure not modify the circuit.
Repairing except indicates causes rising of high
voltage, and it emits an X-ray from the cathode-
ray tube.
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an
electric shock while the electric current is
flowing.
3. USE THE DESIGNATED PARTS
The parts in this equipment have the specific
characters of incombustibility and withstand
voltage for safety. Therefore, the part which is
replaced should be used the part which has
the same character.
7. PERFORM A SAFETY CHECK AFTER
SERVICING
Confirm that the screws, parts and wiring which
were removed in order to service are put in the
original positions, or whether there are the
portions which are deteriorated around the
serviced places serviced or not. Check the
insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
Especially as to the important parts for safety
which is indicated in the circuit diagram or the
table of parts as a
mark, the designated
parts must be used.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING
(INSULATION CHECK PROCEDURE)
1. Unplug the plug from the AC outlet.
2. Remove the antenna terminal on TV and turn
on the TV.
3. Insulation resistance between the cord plug
terminals and the eternal exposure metal
[Note 2] should be more than 1M ohm by
using the 500V insulation resistance meter
[Note1] .
There are parts which use the insulation
material such as a tube or tape for safety, or
which are assembled in the condition that
these do not contact with the printed board.
The inside wiring is designed not to get closer
to the pyrogenic parts and high voltage parts.
Therefore, put these parts in the original
positions.
4. If the insulation resistance is less than 1M
ohm, the inspection repair should be
required.
5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE
[Note 1]
In the condition that an explosion-proof cathode-
ray tube is set in this equipment, safety is
secured against implosion. However, when
removing it or serving from backward, it is
dangerous to give a shock. Take enough care to
deal with it.
If you have not the 500V insulation
resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal
HOW TO ORDER PARTS
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
IMPORTANT
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.
A1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
A1-1
A1-1
A1-1
A2-1
A3-1~A3-4
B-1, B-2
C-1
C-1
C-1
SERVICING NOTICES ON CHECKING......................................................................................................
HOW TO ORDER PARTS ...........................................................................................................................
IMPORTANT................................................................................................................................................
CONTENTS .................................................................................................................................................
GENERAL SPECIFICATIONS ....................................................................................................................
DISASSEMBLY INSTRUCTIONS ...............................................................................................................
SERVICE MODE LIST.................................................................................................................................
CONFIRMATION OF USING HOURS .........................................................................................................
NOTE FOR THE REPLACING OF MEMORY IC ........................................................................................
ELECTRICAL ADJUSTMENTS ..................................................................................................................
MAJOR COMPONENTS LOCATION GUIDE .............................................................................................
BLOCK DIAGRAM ......................................................................................................................................
PRINTED CIRCUIT BOARDS
D1-1~D2-1
D3-1
E-1, E-2
F-1~F-4
MAIN/CRT...........................................................................................................................................
SCHEMATIC DIAGRAMS
G-1, G-2
G-3, G-4
G-5, G-6
G-7, G-8
G-9, G-10
H-1, H-2
I-1
MICON/TUNER..................................................................................................................................
CHROMA ...........................................................................................................................................
DEFLECTION/CRT ............................................................................................................................
POWER .............................................................................................................................................
SOUND ..............................................................................................................................................
WAVEFORMS .............................................................................................................................................
MECHANICAL EXPLODED VIEW ..............................................................................................................
MECHANICAL REPLACEMENT PARTS LIST ..........................................................................................
ELECTRICAL REPLACEMENT PARTS LIST ............................................................................................
J1-1
J2-1, J2-2
A2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SPECIFICATIONS
G-1.Outline of the Product
25 inch( 626 mmV):Measured diagonally
Color CRT
100 degree deflection
G-2.Broadcasting System
US
System
NTSC
M
G-3.Color System
PAL
SECAM or Monochrome signal
G-4.NTSC Playback(PAL 60Hz)
G-5.NTSC 3.58+4.43/PAL60Hz
G-6.Antenna Input Impedance
Yes
Yes
No
No
VHF/UHF 75 ohm unbalanced
G-7.Tuner and Receiving
Contactless Electric tuner
1Tuner System
2Tuner System
channel Tuner
Oscar(W/O HYPER)
France CATV)
Oscar(W/ HYPER)
Others
Receiving channel
(USA)
2-69 ,
4A
,
A-5~A-1 , A~I , J~W , W+1~W+84
Tuning System
Frequency syn.
Voltage syn.
Others
G-8.Preset Channel
-- channels
G-9.Intermediate Frequency
Picture(fP)
45.75 MHz
41.25 MHz
4.50 MHz
MHz
MHz
MHz
MHz
MHz
MHz
Sound (fS)
fP-fS
G-10.Stereo/Dual TV Sound
Yes( NICAM
GERMAN
Yes
USA
JAPAN)
No
G-11.Tuner Sound Muting
G-12.Power Source
No
120
V
AC 50Hz
AC 60Hz
G-13.Power Consumption:
115 W at AC
W at DC
120
120
V
V
V
60 Hz
60 Hz
Stand by:
Per Year:
8
-
W at AC
kWh / Year
G-14.Dimensions(Approx.)
618 mm(W)
504 mm(D)
525 mm(H)
G-15.Weight(Approx.)
Net
Gross:
:
27
29
kg ( 59.9 lbs)
kg ( 64.3 lbs)
G-16.Cabinet Material
Cabinet Front:
PS
ABS
94HB
94V2
94V0
DECABROM
NON-DECA
Back Panel:
PS
ABS
94HB
94V2
94V0
DECABROM
NON-DECA
A3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SPECIFICATIONS
Power Fuse
G-17.Protector:
G-18.Regulation
Safety
UL
CSA
NF
SAA
SI
CE
SEV
BS
SEMKO
NOM
NEMKO
HOMOLO
DENTORI
FEMKO
SABS
UNE
DEMKO
CNS
IEC65
SISIR
NONE
NZ
AS3159
GOST
Radiation
FCC
DOC
FTZ
PTT
CE
HOMOLO
NONE
SEV
UNE
SABA
CNS
SI
NF
NZ
CISPR13
DENTORI
AS/NZS
X-Radiation
PTB
DHHS
HWC
DENTORI
NONE
G-19.Temperature
Operation
Storage
5
-20
˚C~ 40 ˚C
˚C~ 60 ˚C
G-20.Operating Humidity
Less than
80
%RH
G-21.Clock and Timer
Sleep Timer
Yes Max 120
Yes
Yes
Min.( 10 Min. Step)
Programs
Programs
No
No
No
On/Off Timer
Wake Up Timer
G-22.Timer back up Time
More than
-- Minutes (at Power Off Mode)
Din Type
G-23.Terminals
VHF/UHF Antenna Input
F-Type
France Type
Front Video Input
Rear Video Input
Rear Video Output
Front Audio Input
Rear Audio Input
Rear Audio Output
21 Pin
(RCA ø8.3)
(RCA ø8.3)
(RCA ø8.3)
(RCA ø8.3)
(RCA ø8.3)
(RCA ø8.3)
DC Jack(Center +)
AC Outlet
S Input(Front)
Ear Phone Jack(ø3.5)
Ext Speaker
S Input(Rear)
Head Phone Jack(ø3.5)
Diversity
G-24.Indicator
Power
)
Stand By
On Timer
NONE
(
(
)
(
)
G-25.Display
On Screen Display
Menu
Clock Set( 12H 24H)
Hotel Lock
System Selec
Area Code
NICAM Auto Off
Audio
Pin Code Registration
Brightness
Tint(NTSC Only)
Bass
Back Light
Picture Menu
Mid Night Theater
GAME
On/Off Timer
CH Tuning
Picture
Language
V-Chip
Contrast
Sharpness
Treble
Sound 1/2
Guide CH Set
CATV
Control Level
Sound
Color
Tuning
Balance
Stereo,Audio Output,Bilingual
Stereo,Audio Output, SAP
Stereo,Audio Output
AV
Sleep Timer
Channel
Sound Mute
Clock
Pin Code
Hotel Lock
A3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SPECIFICATIONS
G-26.OSD Language
Eng
Ger
Fre
Fre
Spa
Spa
Ita
Ita
Por
Por
Jpn
Jpn
OSD Language Setting
Eng
Ger
Not Applicable
G-27.Speaker
Position
Size
Imp.
Front
1.5 x 2.7 inches
Side
pcs
Bottom
4
ohm x
075 + 0.75
0.5 + 0.5 W (Typical)
2
Power
Max
10%
W
G-28.EXT Speaker
Yes
--
W
Imp
No Need
--
ohm
G-29.Carton
Master Carton:
Content:
Need
---- Set
---- ----
---- mm(W)
Description of Origin Yes
Gift Box
Material
Material:
/
Corrugated Carton
---- mm(D)
No
Dimensions:
---- mm(H)
Double/Brown Corrugated Carton ( with Photo Label)
Double/White Corrugated Carton ( with Photo Label)
Double Full Color Carton W/Photo
Dimensions:
Design:
689 mm(W)
As Per BUYER 's
577 mm(D)
620 mm(H)
Description of Origin:
Yes
No
Drop Test
Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces
Height 25cm 31cm 46cm
204 Sets / 40' container
62cm
80cm
Container Stuffing:
G-30.Accessories
Owner's Manual ( W/Guarantee Card) [ English/French ]
AC Plug Adapter
Battery (UM- 4 x 2
Safety Tip
Channel Film
Remote Control Unit
Toll Free Insert Sheet
)
Guarantee Card
Registration Card
Quick Set-Up Sheet
Information Sheet
Audio-Video Cord (RCA)
Warning Sheet
Schematic Diagram
U/V Mixer
75 ohm Coaxial Cable ( Single Shield
300 ohm to 75 ohm VHF Antenna Adaptor
21pin Cable
Double Shield)
Car Cord
Rod Antenna
One Pole
Loop Antenna
G-31.Other Features
Two Pole ( F-Type
F-Type
Din Type
Din Type
France Type)
France Type)
(
Auto Degauss
Auto Shut Off
Canal+
CATV(181CH)
Anti-Theft
Rental
Auto Search
CH Allocation
SAP
Channel Lock
Just Clock Function
Game Position
TopText
Full OSD
Premiere
Comb Filter
Auto CH Memory
Hotel Lock
Fastext
Closed Caption
V-Chip
Unitext
Picture Menu
Mid Night Theater
A3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SPECIFICATIONS
G-32.Switch
Front
Power(Tact)
System Select
Main Power SW
Channel Up/Reset
Channel Down/Enter
Sub Power
Volume Up/Set Up
Volume Down/Set Down
Menu:Vol UP + Vol Down
Rear
AC/DC
Degauss
TV/CATV Selector
Main Power SW
G-33.Magnetic Field
BV :
BH :
BV :
BH :
+0.45G
0.18G
-0.15G
0.15G
BV :
BH :
BV :
BH :
+0.35G
0.30G
-0.25G
0.15G
BV :
+0.25G
0.30G
-0.50G
0.30G
BH
:
BV :
BH :
G-34.Remote Control Unit:
Glow in Dark Remocon
RC- 74
Yes
No
Power Source:
D.C
3
V
Battery UM - 4 x 2
Total 26 Key
Power
Stand By
0
1
2
3
4
5
Quick View
Status
Time Select
Time Set
Muting
CH Skip
CH1/CH2
Channel
Text/Mix/TV
Display Cancel
Initial
TV/AV
Bar Select
PAL/SECAM
Volume Up
Volume Down
CH Call
CH Down
CH Up
CH Down/Page Down
CH Up/Page Up
Page +/-
6
7
8
9
Store
Program
10
Reveal
F/T/B
11
Sleep
Hold
12
1
Aft/Skip
Preset
List
Rotate
2
0/10
Tone 1/2
Info
Mono/Auto
5.5/6.5MHz
Auto Memory
Auto
Call
Reset
Browse
Std/Auto
Memory
Band Select
Search
TV/Caption/Text
Expand
Red
Menu
Enter
Add
Clock/Program
Clock/Set
Ch Set
Cyan
Delete
Set +
Normal
Yellow
Set -
Color System
Wide Selecy
Auto Wide On/Off
Picture Position
Direct Change/Auto Search
Picture Menu
Random
Tuning Up/Time Text
Tuning Down/Reset
Navi
Green
Nicam/Mono
Tone A/B
FM Transmitter
Back Light
Audio Select
Mid Night Theater
A3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
DISASSEMBLY INSTRUCTIONS
3. After one side is removed, pull in the opposite direction to
remove the other.
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the
Anode Cap, make sure to discharge the Anode Cap's
potential voltage.
Take care not to damage the Rubber Cap.
INSTALLATION
1. Clean the spot where the cap was located with a small
*
Do not use pliers to loosen or tighten the Anode Cap
terminal, this may cause the spring to be damaged.
amount of alcohol. (Refer to Fig. 1-3.)
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap.
(Refer to Fig. 1-1.)
Location of Anode Cap
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.
GND on the CRT
Fig. 1-3
NOTE
Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
CRT
Screwdriver
Support
Alligator Clip
GND on the CRT
Fig. 1-1
2. Flip up the sides of the Rubber Cap in the direction of the
arrow and remove one side of the support.
(Refer to Fig. 1-2.)
Rubber Cap
Fig. 1-4
CRT
Support
Fig. 1-2
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
DISASSEMBLY INSTRUCTIONS
4. Insert one end of the Anode Support into the anode button,
then the other as shown in Fig. 1-5.
Support
CRT
Fig. 1-5
5. Confirm that the Support is securely connected.
6. Put on the Rubber Cap without moving any parts.
2. REMOVAL OF DEFLECTION YOKE
(Refer to Fig. 2-1)
1. Loosen the screw 1.
2. Remove the Convergence • Purity Magnet in the
direction of arrow (A).
3. Loosen the screw 2.
4. Remove the 3 Wedges.
5. Remove the Deflection Yoke in the direction of arrow
(B).
2
1
Wedge
(B)
(A)
Convergence •
Purity Magnet
Deflection Yoke
Wedge
Fig. 2-1
INSTALLATION
Install new Deflection Yoke in reverse steps of REMOVAL.
NOTE
After adjusting the purity and the convergence, fix the
screw 2 and lock the wedges.
B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 1 second.
Set Key
Remocon Key
Operations
0
Releasing of V-CHIP PASSWORD.
Initialization of the factory.
VOL. (-) MIN
VOL. (-) MIN
VOL. (-) MIN
1
6
NOTE: Do not use this for the normal servicing.
POWER ON total hours is displayed on the screen.
Refer to the "CONFIRMATION OF USING HOURS".
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "NOTE FOR THE REPLACING OF MEMORY IC".
Writing of EEPROM initial data.
NOTE: Do not use this for the normal servicing.
VOL. (-) MIN
VOL. (-) MIN
8
9
Display of the Adjustment MENU on the screen.
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
CONFIRMATION OF USING HOURS
POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
ADDRESS
DATA
1. Set the VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel
button (6) on the remote control for more than 1 second.
3. After the confirmation of using hours, turn off the power.
Initial setting content of MEMORY IC.
INIT 00 83
0010
POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
CRT ON
FIG. 1
+ (ones digit value)
NOTE FOR THE REPLACING OF MEMORY IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
INI INI INI INI INI INI INI INI INI INI INI
ADDRESS
00 01 02 03 04 05 06 07 08 09 0A
DATA
A0 01 A2 09 02 63 24 18 A1 21
44
Table 1
1.
2.
Enter DATA SET mode by setting VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second.
ADDRESS and DATA should appear as FIG 1.
3.
ADDRESS is now selected and should "blink". Using the SET + or - keys on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
4.
5.
6.
7.
8.
Press ENTER to select DATA. When DATA is selected, it will "blink".
Again, step through the DATA using SET + or - until required DATA value has been selected.
Pressing ENTER will take you back to ADDRESS for further selection if necessary.
Repeat steps 3 to 6 until all data has been checked.
When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
The unit will now have the correct DATA for the new MEMORY IC.
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL
2. BASIC ADJUSTMENTS
ADJUSTMENTS
2-1: RF AGC DELAY
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
1. Receive an 80dB monoscope pattern.
2. Connect the digital voltmeter to TP001.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (02) on the remote control to
select "RF DELAY".
CAUTION
• Use an isolation transformer when performing any
service on this chassis.
• Before removing the anode cap, discharge electricity
because it contains high voltage.
4. Press the VOL. UP/DOWN button on the remote control
until the digital voltmeter is 1.80 ± 0.05V.
• When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
Inferior silicon grease can damage IC's and transistors.
• When replacing IC's and transistors, use only specified
silicon grease (YG6260M).
2-2: CUT OFF
1. Adjust the unit to the following settings.
R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64,
B.BIAS=64, BRIGHTNESS=126, CONTRAST=100.
2. Place the set with Aging Test for more than 15 minutes.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (01) on the remote control to
select "CUT OFF".
Remove all old silicon before applying new silicon.
Prepare the following measurement tools for electrical
adjustments.
4. Adjust the Screen Volume until a dim raster is obtained.
1. Synchro Scope
2. Digital Voltmeter
2-3: WHITE BALANCE
NOTE: Adjust after performing CUT OFF adjustment.
On-Screen Display Adjustment
1. Place the set with Aging Test for more than 10 minutes.
2. Receive the with 100% signal from the pattern generator.
3. Using the remote control, set the brightness and contrast to
normal position.
4. Activate the adjustment mode display of Fig. 1-1 and press
the channel button (10) on the remote control to select
"R.BIAS".
1. In the condition of NO indication on the screen.
Press the VOL. DOWN button on the set and the
Channel button (9) on the remote control for more than
1 second to appear the adjustment mode on the screen
as shown in Fig. 1-1.
5. Using the VOL. UP/DOWN button on the remote control,
adjust the R.BIAS.
TV
6. Press the CH. UP/DOWN button on the remote control to
select the "R.DRIVE", "B.DRIVE", "G.BIAS" or "B.BIAS".
7. Using the VOL. UP/DOWN button on the remote control,
adjust the R.DRIVE, B.DRIVE, G.BIAS or B.BIAS.
8. Perform the above adjustments 6 and 7 until the white
color is looked like a white.
00 OSD
15
Fig. 1-1
2-4: FOCUS
2. Use the Channel UP/DOWN button or Channel button
(0-9) on the remote control to select the options shown
in Fig. 1-2.
3. Press the MENU button on the remote control to end
the adjustments.
1. Receive the monoscope pattern.
2. Turn the Focus Volume fully counterclockwise once.
3. Adjust the Focus Volume until picture is distinct.
2-5: SUB TINT/SUB COLOR
1. Receive the color bar pattern.
NO. FUNCTION
00 OSD H
01 CUT OFF
02 RF DELAY
03 VIF VCO
04 H VCO
05 H PHASE
06 V SIZE
07 V SHIFT
08 R DRIVE
09 B DRIVE
10 R BIAS
NO. FUNCTION
13 BRIGHTNESS
14 CONTRAST
15 COLOR
2. Connect the synchro scope to TP023.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "TINT".
4. Press the VOL. UP/DOWN button on the remote control
until the waveform becomes as shown in Fig. 2-1.
5. Connect the synchro scope to TP022.
6. Press the CH DOWN button once to set to "COLOR"
mode.
16 TINT
17 SHARPNESS
18 FM LEVEL
19 LEVEL
20 SEPARATION 1
21 SEPARATION 2
22 TEST MONO
23 TEST STEREO
24 X-RAY TEST
7. Press the VOL. UP/DOWN button on the remote control
until the red color level is adjusted to 110% of the white
level. (Refer to Fig. 2-2)
11 G BIAS
12 B BIAS
Fig. 1-2
D1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL ADJUSTMENTS
TV
Fig. 2-1
00 OSD
15
A
B
Fig. 2-3
0%
2-9: OSD HORIZONTAL
110%
1. Activate the adjustment mode display of Fig. 1-1.
2. Press the VOL. UP/DOWN button on the remote
control until the difference of A and B becomes
minimum. (Refer to Fig. 2-3)
100%
Fig. 2-2
2-10: VERTICAL VCO
1. Place the set with Aging Test for more than 15 minutes.
2. Receive an 80dB monoscope pattern.
3. Connect the digital voltmeter between the pin 5 of
CP601.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (03) on the remote control to
select "VIF VCO".
2-6: HORIZONTAL PHASE
1. Receive the center cross signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
Fig. 1-1 and
(05) on the remote control to
3. Activate the adjustment mode display of
5. Press the VOL. UP/DOWN button on the remote control
until the digital voltmeter is 2.5V.
press the channel button
select "H.PHASE".
4. Press the VOL. UP/DOWN button on the remote
control until the SHIFT quantity of the OVER SCAN on
right and left becomes minimum.
2-11: SUB BRIGHTNESS
1. Receive the black pattern*. (RF Input)
2. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (13) on the remote control to
select "BRIGHTNESS".
3. Press the VOL. UP/DOWN button on the remote control
unit the screen begin to shine.
2-7: VERTICAL SIZE
NOTE: Adjust after performing adjustments in section 2-6
1. Receive the crosshatch signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
2-12: SUB CONTRAST
Fig. 1-1 and
3. Activate the adjustment mode display of
1. Receive the color bar pattern.
(06) on the remote control to
2. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (14) on the remote control to
select "CONTRAST".
3. Press the VOL. UP/DOWN button on the remote control
unit the nit for more than 200 nit.
press the channel button
select "V.SIZE".
4. Press the VOL. UP/DOWN button on the remote control
until the rectangle on the center of the screen becomes
square.
5. Receive a broadcast and check if the picture is normal.
2-8: VERTICAL SHIFT
NOTE: Adjust after performing adjustments in section 2-7
1. Receive the crosshatch signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
Fig. 1-1
3. Activate the adjustment mode display of
(07) on the remote control to
and press the channel button
select "V.SHIFT".
4. Press the VOL. UP/DOWN button on the remote
control until the horizontal line becomes fit to the notch
of the shadow mask.
D1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL ADJUSTMENTS
3-3: STATIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 3-2.
3. PURITY AND CONVERGENCE
ADJUSTMENTS
NOTE
1. Receive the crosshatch pattern from the color bar
generator.
2. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets.
1. Turn the unit on and let it warm up for at least 30
minutes before performing the following adjustments.
2. Place the CRT surface facing east or west to reduce the
terrestrial magnetism.
3. Turn ON the unit and demagnetize with a Degauss Coil.
3. Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)
1. Tighten the screw for the magnet. Refer to the adjusted
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body,
untighten the screw for the body.
2. Receive the green raster pattern from the color bar
generator.
3. Slide the deflection yoke until it touches the funnel
side of the CRT.
4. Adjust center of screen to green, with red and blue on the
sides, using the pair of purity magnets.
5. Switch the color bar generator from the green raster
pattern to the crosshatch pattern.
6. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets.
7. Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
3-4: DYNAMIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 3-3.
1. Adjust the differences around the screen by moving
the deflection yoke upward/downward and right/left.
(Refer to Fig. 3-2-a)
2. Insert three wedges between the deflection yoke and
CRT funnel to fix the deflection yoke.
(Refer to Fig. 3-2-b)
R G B
R G B
R
G
B
8. Adjust the crosshatch pattern to change to white
by repeating steps 6 and 7.
R
G
B
3-2: PURITY
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
NOTE
Fig. 3-2-a
Adjust after performing adjustments in section 3-1.
1. Receive the green raster pattern from color bar
generator.
2. Adjust the pair of purity magnets to center the
color on the screen.
Adjust the pair of purity magnets so the color at the
ends are equally wide.
WEDGE
WEDGE
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole
screen is green.
4. Confirm red and blue colors.
5. Adjust the slant of the deflection yoke while watching the
screen, then tighten the fixing screw.
WEDGE
DEFLECTION YOKE
DEFLECTION YOKE SCREW
MAGNET SCREW
WEDGE POSITION
Fig. 3-2-b
PURITY MAGNETS
6 POLE MAGNETS
4 POLE MAGNETS
Fig. 3-1
D2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
MAJOR COMPONENTS LOCATION GUIDE
TU001
FB401
TP001
CP601
FOCUS VOLUME
SCREEN VOLUME
MAIN PCB
TP023
TP024
J801
TP022
CRT PCB
D3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
BLOCK DIAGRAM
Q351
MUTE SW.
TU001
11
CHROMA IC
IC601 M61203BFP
CH UP
X602
3.579545MHz
IC351 AN7523
4
VOL UP
CH DOWN
VOL DOWN
POWER
1
X' TAL
5
32
AUDIO OUT
REG OUT
50
33
6
2
4
MICON IC
IC101 OEC7044A
SOUND IC
SP351
62
RF AGC OUT
CF601
SAW FILTER
9
64
1
VIF IN (1)
VIF IN (2)
Q606
REG.
5
AUDIO MUTE
KEY2
P. CON+15V
26
Q801
RED OUT
CVIN
40
30
28
20
Y SW OUT
R IN
17
R OUT
G OUT
RED R 42
14
15
KEY1
27
41
40
39
Q803
GREEN G
BLUE B
G IN
GREEN OUT
B OUT 16
B IN
Q603
REG.
OS101
BLANK BL
10 REMOCON
Q802
27 FAST BLK
REG OUT
41
6
1
2
3
BLUE OUT
H. SYNC
1
12
29
5
INV FBP OUT
V PULSE OUT
SCL
FBP IN
Q608
V. SYNC
SCL1
2
CUT OFF
START UP
VCC
19
7
34
32
25
POWER
SDA1
36
H OUT
SDA
10
42
RESET
19 XIN
MCU RESET
X101
8MHz
Q402
H. DRIVE
Q401
H. OUTPUT
VREG VCC
55
6
5
SDA
MEMORY IC
SCL IC199
S-24C02BDP-1A
17 V OUT
XOUT
20
Q101
Q501
POWER
X_RAY_TEST
30
X-RAY TEST SW
V-OUT IC
IC401 LA78041
POWER REG. IC
IC501
STR30110
PUMP UP
6
11
B
8
G
R
-
CRT
AMP
DEGAUSS COIL
L502
+
Heater
10
4
3
Q403
X-RAY TEST SW.
VCC
6
9
F
D501~D504
RECTIFIER
7
2
5
+B
RY101
1
IC402
KIA7805API
4
3
P. CON+5V
REG IC
DY
2
1
3
FB401
D127
L501
4
1
P. CON+5V
9
F
1
2
3
5
D404
5
S
10
HV
3
F501
AC IN
E-1
E-2
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTED CIRCUIT BOARDS
MAIN/CRT (INSERTED PARTS)
SOLDER SIDE
CP802A
D405
R422
C401
TP501
CP803A
CP601
R509
W010
TU001
D605
TP001
R001
R429_1
IC501
D410
D422
HS501
R002
C404
C412
W818
C004
D408
D404
FB401
D401
W019
L406
R503
D407
D402
R508
Q403
R506
W004
R412
W897
W088
W074
R410
W014
S104Y
CP401_1
R427
W831
W817
HS401
W813
IC401
R502
*
R417
W059
T401_1
*
S803X
R407_2
W823
W824
R177
IC351_1
C359_1
R655
R448_1
C133
C506_1
S801Y
D126
R640
D127
S801X
D609
C351
Q351
W007
C647
RY101
D617
CP351_1
S809Y
R443_1
S809X
S802Y
Q606
CP502
L501
CF604
CF603
CC004
CP802B
C630
W092
S104X
C631
D608
Q801
W805
C636
C624
IC402
W108
Q501
C129
IC199
S803Y
W812
Q101
L601
S106Y
Q802
Q803
TP023
S106X
R815
C625
CF601
S105Y
Q603
TP022
TP024
C125
R806
W042
W041
C661
C639
*
W071
D603
W011
W806
W837
X101_1
L603
W029
C802_1
CP803B
D610
CP806
FH502
F501 FH501
D104
SW102
SW105
D612
6.3A125V
D103
OS101
SW104
SW101
SW103
F-1
F-2
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTED CIRCUIT BOARDS
MAIN/CRT (CHIP MOUNTED PARTS)
SOLDER SIDE
R638
C113
R642
C699
17
IC601
49
IC101
C634_1
1
33
R603
R111
C642
R611
F-4
F-3
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
D
E
F
G
H
MICON/TUNER SCHEMATIC DIAGRAM
(MAIN PCB)
8
8
TU001 NJH3021U268
ACCESORY
ATC001
NXC0032-010010
TP001
TM101
R25-1127
C003
FROM DEFLECTION/CRT
P_CON+5V
50V4.7 KA
7
7
OS101
PIC-28143SY-2
FROM POWER
GND
R001
S809X
+B
68K1/2W
R002
FROM/TO CHROMA
68K 1/2W
AGC
IF
6
6
I2C_OFF
VD
HD
MICON IC
IC101
3
OEC7044A
RED R
R123
0
0
4.9
OSD_R
OSD_G
OSD_B
P50/H.SYNC
P51/V.SYNC
4.7K
R122
4.9
GREEN G
BLUE B
4.7K
R121
4
0
0
0
P00/EXT MUTE
P01/I2C_OFF
P02/AUDIO MUTE
P03/(Surround)
P04
4.7K
R120
R116
47K
4.9
0
OSD_BLK
OUT1/BLANK BL
P20/AV2
R117
47K
4.7K
5
5
R111
10K
0
NC
GND
SCL
0
0
NC
P21/AV1
SDA
POWER
4.9
0
P22/POWER
0
NC
0
TO SOUND
P05/(Center_SP) P10/DEGAUSS_H
AUDIO_MUTE
R114
10K
4.9
4.8
4.8
3.9
INT2/P.FAIL
INT1/REMOCON
P23/SYNC
P24
SCL1
SCL2
C117
0
NC
270P B
R105
TO POWER
POWER
D104
R115
47K
4
3
2
4
3
2
MTZJ6.8B
5.0
4.7K
C116
SDA1
SDA2
FROM/TO DEFLECTION/CRT
X-RAY_TEST
0
NC
0
NC
270P B
R106
16.0
X-RAY TEST SW
Q101
DTC114TS
X-RAY
0
4.7K
0
0
NC
P25/ON_TIMER AD1/X_RAY_TEST
W812
R107
10K
0
4.9
3.0
0
AVCC
HLF
X-RAY
AD4/AFT
R130
1K
C122
FROM CHROMA
AFT
C121
3.2
4.9
50V1 KA
200P CH
D101
MTZJ6.8B
MTZJ6.8B
C120
FROM CHROMA
SYNC
0.8
3.4
0
V.HOLD
CVIN
CNVSS
Xin
AD5/KEY1
AD6/KEY2
R112
0.001 Y
C124
D103
2
4.9
4.9
2.2K
R113
Y_VIDEO
50V 0.1 KA
AT+5V
RESET
C130
0.001
R119
1K
2.2K
RESET
OSC1
B
C114
10P CH
1
3.7
4.2
0
3.6
C113
Xout
OSC2
VCC
4.1
4.9
X101_1
CST8.00MTW
10P CH
VSS
C119
5.0
5.0
0
5.0
0.68 TF
C118
R126
2.7K
R101
560
5
4
6
3
7
2
8
1
R128
560
6.3V 470
YK
0
0
0
0
THE DC VOLTAGE AT EACH PART WAS MEASURED
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
CAUTION: DIGITAL TRANSISTOR
NOTE:
TUNER VIDEO SIGNAL
R.SIGNAL
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
DESCRIBED IN PARTS LIST ONLY
1
1
PCB010
TMX456
G.SIGNAL
DANS LA NOMENCLATURE DES PIECES
B.SIGNAL
DEFLECTION SIGNAL
A
B
C
D
E
F
G
H
G-1
-2
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
D
E
F
G
H
CHROMA SCHEMATIC DIAGRAM
8
8
(MAIN PCB)
TO MICON/TUNER
SYNC
Y_VIDEO
AT+5V
6
4.8
10.6
5.5
FROM POWER
P_CON+15V
REG.
Q603
8.2
8.8
15.0
REG.
2SD734
7
7
S802Y S802X
RESET
7
Q606
2SD734
CF604
EFCT4R5MW5
FROM POWER
AT+15V
W828
R615
470
CF603
EFCT4R5YS5A
R638 6.8K
D607
C661 0.01 Y
R646 12K
1SS133
6
6
2.9 2.3
0
46
8.2
45
8.2 3.9 4.8 5.5 3.4 0 NC
44 43 42 41 40 39
0
0
2.9 3.3 2.0 8.8
TO SOUND
GND
48
47
38
37
36
35
34
33
C638
R634
10K
10K
2.3
3.0
2.3
3.2
3.5
2.6
50V4.7 NA
D605
R611
5
R612
5.6K
R642
100K
AUDIO_OUT
11E1-EIC
C604 50V 1 KA
0
AUDIO BYPASS
EXT AUDIO IN
R IN
C642 0.001
Y
5.0
0
V PULSE OUT
G OUT
C623 0.0033
M
3.8
3.1
9.2
3.0
2.6
0
FM DIRECT OUT
VIF VCO F/B
46 SW REG CONT
47 LIMITER IN
48 IF AGC
34 EXT C in
33 8.7V REG OUT
32 X’TAL
C632 50V 2.2 KA
0
FAST BLK
SPOT KILLER
fsc OUT
R618 10M1/4W
5
5
C610
49 QIF OUT
31 ACL/ABCL
7.3
VREG Vcc
50 AUDIO OUT
50V 0.22 YK
C645
0
NC
VIF APC FILTER
VIF VIDEO OUT
VIF GND
16V 47 YK
D614
5.0
5.0
5.6
2.5
FROM/TO DEFLECTION/CRT
MTZJ6.2B
VIDEO CHROMA Vcc
V RAMP CAP
S106Y
ABCL
C613_1
TF
0
1
C621 0.01
B
P_CON+5V
V_FEEDBACK
R641
20K
3.2
2.9
1.8
AFT OUT
QIF IN
V RAMP FEEDBACK
B IN
W819
C626
64 VIF IN
1 VIF IN
17 V OUT
16 B OUT
0
D615 MTZJ6.2B
0.001 Y
R606
10K
8.2
4
3
2
4
3
2
RF AGC OUT
STRAT UP Vcc
C654 0.022
F
C606
50V 0.1 KA
2.9
1.8
CHROMA IC
IC601
RF AGC FILTER
8.2
4.5
SAW FILTER
CF601
SAF45MFY220ZR
R644
V_OUT
GND
1001/4W
D616
10
5
4
3
2
M61203BFP
1
2
3
4
5
6
7
8
9
10
4.9
11
12
13
14
15
16
4.8
0
1.5
5.0 5.0
2.7 4.9
6.2 6.2
0
3.5 4.9 4.9 4.0 4.0
MTZJ6.2B
11
12
13
9
H_OUT
H_SYNC
R627 100
R630 100
R631 100
8
B.OUT
G.OUT
R.OUT
CLAMP
FROM/TO MICON/TUNER
L601
1.2uH
TEST POINT
AFT
AGC
IF
R617 2.7K
CP601
TKC-M06X-A1
CUT OFF
Q608
2SA1015Y
B.OUT
6
5
4
3
2
1
0.8
0
D603
D604
INT.MONI
IIC_OFF
SDA
GND
0.1
1SS133 1SS133
HD
POWER
OSD_B
OSD_BLK
OSD_G
VD
SCL
GND
OSD_R
I2C_OFF
SDA
SCL
DEFLECTION SIGNAL
AUDIO SIGNAL
LUMINANCE SIGNAL
TUNER VIDEO SIGNAL
R.SIGNAL
G.SIGNAL
B.SIGNAL
THE DC VOLTAGE AT EACH PART WAS MEASURED
NOTE:
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
PCB010
TMX456
1
1
A
B
C
D
E
F
G
H
G-3
G-4
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
D
E
F
G
H
(MAIN PCB)
DEFLECTION/CRT SCHEMATIC DIAGRAM
CD802
8
8
2E054401
GND
GND
FROM/TO CHROMA
GND
CLAMP
G.OUT
B.OUT
R.OUT
5
4
3
2
1
5
4
3
2
1
GND
CLAMP
G.OUT
B.OUT
R.OUT
CLAMP
G.OUT
B.OUT
R.OUT
CLAMP
G.OUT
CLAMP
G.OUT
B.OUT
R.OUT
B.OUT
R.OUT
V-OUT IC
IC401 LA78041
V_OUT
CP802A
CP802B
51048-0510
51048-0510
V_FEEDBACK
HS401
763WAA0119
L802
HF57T18.5*10*10
THERMAL
PROTECTION
PUMP
UP
CD801_1
8M82025A
CP801_1
TS-80P-02-V1
-
AMP
+
1
2
VCC
6
1
2
7
7
W831
1
2
3
4
5
7
4.5 25.1 27.0
0
53.0
52.0
4.4
W817
14
3.2
3.2
3.2
2.7
18
D403
100.6
2.7
98.4
2.7
95.4
V801
19
11E1-EIC
A63AHC26X
RED OUT
Q801
2SC4075-YAC
GREEN OUT
Q803
2SC4075-YAC
BLUE OUT
Q802
2SC4075-YAC
R418
9
10
8
R
22K +-1%
CC004
R420
6.8K
G
6
6
6
B
11
CC002
CC006
5
7
1
DY801
7M062505
TO DY
TP022
TP023
TP024
S803X
4
3
2
1
4
3
2
1
R404
2.7K 1/4W
20
22
21
X-RAY TEST SW.
Q403
DTA144ES
MG801
29MMSTAR
R405
18K 1/4W
+-1%
5
5
16.0
9.6
R401
16.1
CP401_1
100K 1/4W
+-1%
TS-80P-04-V1
C434
100V 22 YK
FROM/TO MICON/TUNER
D402
R424
R409
6.2K +-1%
K001
8115529
X-RAY
X-RAY_TEST
P_CON+5V
HZ11B1L
12K +-1%
K002
8115529
15
C439
SL
500V22P
K003
8115529
FROM/TO CHROMA
H.DRIVE
Q402
2SC2621
R429_1
GND
ABCL
FB401
3225010F
4
3
2
4
3
2
1.8 2W
0
R
B
G
27.0
0
17.7
W897
17
H_OUT
0
COL
130.0
0.3
1
HV
H.OUTPUT
Q401
-0.1
16
H_SYNC
P_CON+5V
45.7
2SD2499(LBOEC1)
0
130.0
T401_1
5013001
D410
AU02A-EIC
FOCUS
135.0 VIDEO
F
S
6
0
SCREEN
1
B+
135.0
2
CP806
005P-2100
W891
GND
0
11
P.CON+5V REG IC
IC402 KIA7805API
L406 18uH
C416
-1.9
0
AFC
HEA
TER
9
10
8
ABL
R428_1
8.2 2W
1.7
7
200V
PP
0.018
R422
W838
0
GND
6.8K 1/2W
C401
1.5 E12
4
GND
C446
C404
8
NC
2.0 E25
3
IN
1
GND OUT
SL
500V22P
E8 0.8
160V 1 MHE
10V 470 YK
5
2
3
7.8
0
5.0
D408
AU02A-EIC
R448_1
W823
W824
D407
3.3K 5W
AU02A-EIC
96.4
NC
TO SOUND
6.4
P_CON+5V
SOUND+B
0
C448
22
R443_1
R445_1
D422
AU02A-EIC
100V
YK
101.6
100K
1/4W
4.7 2W
0
FROM/TO POWER
HEATER
HEATER
GND
99.6
HEATER
GND
4
3
2
1
4
3
2
1
J801
0
GND
GND
180V
CVT3275-5102
+B
GND
GND
GND
180V
180V
CD803
2E044101
CP803A
51052-0400
CP803B
51052-0400
D404
FBT+12V
AU02A-EIC
PCB110
TCX315
PCB010
TMX456
CAUTION: DIGITAL TRANSISTOR
R.SIGNAL
G.SIGNAL
B.SIGNAL
1
1
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
THE DC VOLTAGE AT EACH PART WAS MEASURED
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
NOTE:
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
DESCRIBED IN PARTS LIST ONLY
DEFLECTION SIGNAL
A
B
C
D
E
F
G
H
G-5
-
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
D
E
F
G
H
POWER SCHEMATIC DIAGRAM
8
8
(MAIN PCB)
CAUTION:
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE 6.3A 125V (F501)
FUSE.
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES
D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME
TYPE 6.3A 125V (F501).
6.3A 125V
7
7
DEGAUSS COIL
L502
8R250009
R502
1.2 7W
2
1
R640
D609
EM1C-EIC
2.2K 10W
R655
CP502
TV-50P-02-A1
POWER REG.IC
IC501 STR30110
C647
D501
D502
6
6
500V 0.001
B
2.2K 10W
RM11C-EIC
RM11C-EIC
MS501
23MICA
D504
D503
RY101
1
2
3
4
5
ALKS321
3
1
RM11C-EIC
RM11C-EIC
TH501
PTAD14K2-3R0Q141
0
137.3 179.6 136.6
6.9
P
H
2
TP501
D125
1SS133
POWER
Q501
HS501
763WAA0112
2SC1815Y
0
R504
4.7K
R177
0.7
D126
5
W818
5
0
EM1C-EIC 1.2K 10W
C133
R506
NC
AC120V_60HZ
CD501
0R614909
6.3A 125V
180 20W
500V 0.001
B
6.3A 125V
F501
L501
9-000074
BLACK
WHITE
FH502
EYF-52BC
FH501
23706.3
C501
EYF-52BC
250V 0.22 ECQUL
D617
11E1-EIC
C646
CP501
THL-P03P-B1
R515
1.5 3W
C132_1
25V 2200 YK
D608
R643
4
3
2
4
3
2
25V 2200 MHE
S803Y
33 1/2W
RD15FB
FBT+12V
D127
11E1-EIC
+B
W801
W815
GND
FROM/TO MICON/TUNER
FROM/TO DEFLECTION/CRT
GND
+B
POWER
TO CHROMA
P_CON+15V
AT+15V
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
THE DC VOLTAGE AT EACH PART WAS MEASURED
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
NOTE:
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
DESCRIBED IN PARTS LIST ONLY
1
1
PCB010
TMX456
DANS LA NOMENCLATURE DES PIECES
A
B
C
D
E
F
G
H
G-7
G-8
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
D
E
F
G
H
SOUND SCHEMATIC DIAGRAM
8
8
FROM MICON/TUNER
AUDIO_MUTE
(MAIN PCB)
FROM CHROMA
7
7
AUDIO_OUT
GND
6
6
5
5
FROM DEFLECTION/CRT
P_CON+5V
SPEAKER
SP351_2
SA04A05AWA
CP351_1
TID-X02P-B2
SOUND+B
SOUND IC
IC351_1
1
2
1
2
AN7523
SPEAKER
4
3
2
4
3
2
SP351_2
SA04A05AWA
+
-
+
-
+
-
GND
VCC
1
5.7
2
3
0
4
5
6
7
0
8
9
4.6
4.6
4.1
1.6
0
2.9
NC
W834
24
W820
S801Y
S801X
S809Y
W829
W810
23
W813
MUTE SW.
Q351
2SC1815Y
2.9
R354
47K
0
0
W814
PCB010
TMX456
1
1
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
THE DC VOLTAGE AT EACH PART WAS MEASURED
CAUTION: SINCE THESE PARTS MARKED BY
ARE
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
NOTE:
AUDIO SIGNAL
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
DANS LA NOMENCLATURE DES PIECES
A
B
C
D
E
F
G
H
G-9
G-10
Download from Www.Somanuals.com. All Manuals Search And Download.
WAVEFORMS
MICON/TUNER
1V 20µs/div
11
1 200mV 5ms/div
6
0.5V 20µs/div
1V 20µs/div
12
200mV 20µs/div
7
2
0.5V 20µs/div
13 1V 20µs/div
3
20V 20µs/div
8
200mV 20µs/div
DEFLECTION/CRT
200mV 5ms/div
0.5V 5ms/div
14
4
9 200mV 20µs/div
CHROMA
15 20V 20µs/div
0.5V 5ms/div
10
5
0.5V 2ms/div
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-1
Download from Www.Somanuals.com. All Manuals Search And Download.
WAVEFORMS
16 2V 20µs/div
21 50V 20µs/div
22 50V 20µs/div
200V 20µs/div
17
SOUND
23
18 10V 5ms/div
0.5V 1ms/div
19
24 1V 1ms/div
10V 5ms/div
50V 20µs/div
20
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MECHANICAL EXPLODED VIEW
111
204
204
204
204
204
113
J801
119
205
204
204
110
116
205
105
119
PCB110
114
(CRT PCB)
203
L502
205
205
101
MS501
FB401
202
102
202
103
115
V801
104
203
115
ATC001
TU001
112
203
PCB010
(MAIN PCB)
SP351
201
201
117
108
118
109
201
107
120
106
I-1
Download from Www.Somanuals.com. All Manuals Search And Download.
MECHANICAL REPLACEMENT PARTS LIST
REF. NO. PART NO.
DESCRIPTION
101
102
103
104
105
106
107
108
109
8995034000 CORD CLIP UL CO.
---
---
---
HEAT SINK
HEAT SINK
METAL SPACER
741WUA0021 SPRING,EARTH
701APJA036 CABINET,FRONT
713WPA0096 GUIDE,REMOCON
7230006856 SHEET,CAUTION
735WPA0426 BUTTON ASS'Y
110
111
112
113
114
115
116
117
118
119
702APA0086 CABINET,BACK
722552A004 SHEET,RATING
723000B179 FILM,DECORATION
7232020733 SHEET,BRAND
899HV3T001 HOLDER,ANODE WIRE
762WPA0009 HOLDER,CRT WIRE
8994201000 HOLDER,CRT WIRE
7220001109 SHEET,HWC
7240001041 SHEET,CSA WARNING
---
COATING CLIP
120
A3I062G720 CABINET,FRONT ASS'Y
201
202
203
204
205
8110630A04 SCREW,TAP TITE (P)
8117D30A04 SCREW,TAPPING (B0)
8109630802 SCREW,TAP TITE (B)
8117540B04 SCREW,TAPPING (B0)
8111J50D04 SCREW,TAPPING (A)
BRAZIER
WH8 BRAZIER 3x10
BRAZIER
TRUSS
GW22
3x10
3x8
4x20
5x40
---
---
---
---
---
---
J3I06201
JB5U0100 POLYBAG
792AHA0073 PACKAGE,TOP
792AHA0074 PACKAGE,BOTTOM
791AHA0021 FILM BAG
INSTRUCTION BOOK
793ACDA087 GIFT BOX
J1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO.
DESCRIPTION
RESISTORS
REF. NO. PART NO.
DESCRIPTION
DIODES
R135
R177
R401
R404
R405
R406
R407
R408
R409
R417
R418
R424
R428
R429
R430
R443
R448
R501
R502
R506
R507
R509
R515
R640
R647
R655
R803
R805
R807
R001T6272J RC
2.7K OHM 1/6W
D604
D605
D607
D608
D609
D610
D611
D612
D614
D615
D616
D617
D1VT001330 DIODE, SILICON
D2WT011E10 DIODE, SILICON
D1VT001330 DIODE, SILICON
D9201150B1 DIODE, ZENER
D2WT0EM1C0 DIODE, SILICON
D97U01201B DIODE, ZENER
D97U01201B DIODE, ZENER
D97U01201B DIODE, ZENER
D97U06R21B DIODE, ZENER
D97U06R21B DIODE, ZENER
D97U06R21B DIODE, ZENER
D2WT011E10 DIODE, SILICON
ICS
I56F07044A IC
A3I051G015 IC
I0FSP75230 IC
I03TD80410 IC
I1KA97805A IC
I2B4901100 IC
I06FC12030 IC
1SS133T-77
11E1-EIC
1SS133T-77
RD15FB
EM1C-EIC
MTZJ12B T-77
MTZJ12B T-77
MTZJ12B T-77
MTZJ6.2B T-77
MTZJ6.2B T-77
MTZJ6.2B T-77
11E1-EIC
!
!
!
!
!
!
!
!
R5W2CF122J R, CEMENT
R4X5T4104F R, METAL
R002T4272J RC
R4X5T4183F R, METAL
R903N8332J RC
1.2K OHM 10W
100K OHM 1/4W
2.7K OHM 1/4W
18K OHM 1/4W
3.3K OHM 1/8W
R65581010J R, FUSE
R4X5T6183F R, METAL
R4X5T6622F R, METAL
R4X5T6113F R, METAL
R4X5T6223F R, METAL
R4X5T6123F R, METAL
R3X28A8R2J R, METAL
R6558A1R8J R, FUSE
R00106104J RC
R6558A4R7J R, FUSE
R5X2CD332J R, CEMENT
R21202105K R, SOLID
R5X2CE1R2J R, CEMENT
R5W2CH181J R, CEMENT
R655U4470J R, FUSE
R4X5T6183F R, METAL
R3X28B1R5J R, METAL
R5X2CF222J R, CEMENT
R00106182J RC
1
OHM 1W
18K OHM 1/6W
6.2K OHM 1/6W
11K OHM 1/6W
22K OHM 1/6W
12K OHM 1/6W
8.2 OHM 2W
1.8 OHM 2W
100K OHM 1/6W
4.7 OHM 2W
3.3K OHM 5W
1M OHM 1/2W
1.2 OHM 7W
180 OHM 20W
47 OHM 1/4W
18K OHM 1/6W
1.5 OHM 3W
2.2K OHM 10W
1.8K OHM 1/6W
2.2K OHM 10W
12K OHM 2W
12K OHM 2W
12K OHM 2W
!
!
!
IC101
IC199
IC351
IC401
IC402
IC501
IC601
OEC7044A
S-24C02BDP-1A
AN7523
!
!
!
!
!
!
LA78041
KIA7805API
STR30110
M61203BFP
!
TRANSISTORS
!
!
!
!
Q101
Q351
Q401
Q402
Q403
Q501
Q603
Q606
Q608
Q801
Q802
Q803
TNYTJ03001 COMPOUND TRANSISTOR
TC5T018154 TRANSISTOR, SILICON
TDUU024990 TRANSISTOR, SILICON
TC3Q026210 TRANSISTOR, SILICON
TPYTD03001 COMPOUND TRANSISTOR
TC5T018154 TRANSISTOR, SILICON
TD3T007340 TRANSISTOR, SILICON
TD3T007340 TRANSISTOR, SILICON
TA5T010154 TRANSISTOR, SILICON
TC3Q040750 TRANSISTOR, SILICON
TC3Q040750 TRANSISTOR, SILICON
TC3Q040750 TRANSISTOR, SILICON
COILS &TRANSFORMERS
021LA63R3K COIL
DTC114TSTP
2SC1815Y(TPE2)
2SD2499(LBOEC1)
2SC2621(D,E)-RAC
DTA144ESTP
2SC1815Y(TPE2)
2SD734(E,F)-AA
2SD734(E,F)-AA
2SA1015Y(TPE2)
2SC4075-YAC
!
!
!
!
!
!
R5X2CF222J R, CEMENT
R3X18A123J R, METAL OXIDE
R3X18A123J R, METAL OXIDE
R3X18A123J R, METAL OXIDE
CAPACITORS
C132
C351
C404
C405
C412
C414
C416
C418
C433
C434
C437
C443
C444
C446
C448
C501
C506
C507
C519
C624
C646
C699
E5EZF3222M CE
E02LF1332M CE
E02LT1471M CE
E02LT2471M CE
E02LT1471M CE
E5EZT4101M CE
P3N1F2183J CPP
E5EZF3222M CE
E02LT4471M CE
E02LT8220M CE
P411F3564J CMPP
P414F9103H CMPP
C01BBP7H2K CC
E5EZTB010M CE
E02LT8220M CE
P2122B224M CMP
E52SFC681M CE
E5EZFB101M CE
E5EZTB100M CE
E02L01222M CE
E02LF3222M CE
CHGTY0214M CC
2200 UF 25V
3300 UF 10V
470 UF 10V
470 UF 16V
470 UF 10V
!
!
!
2SC4075-YAC
2SC4075-YAC
!
!
!
!
L101
L406
L501
L502
L601
L603
L605
L607
L801
L802
T401
3.3 UH
18 UH
9-000074
8R250009
1.2 UH
10 UH
100 UF 35V
021U6D180K COIL
0.018 UF 200V
2200 UF 25V
470 UF 35V
22 UF 100V
0.56 UF 250V ECWF
0.01 UF 1.6KV ECWH
220 PF 2KV BP
1UF 160V
22 UF 100V
0.22 UF 250V ECQUL
680 UF 200V
100 UF 160V
10UF 160V
2200 UF 10V
2200 UF 25V
0.01 UF 16V Y
!
!
029K000074 COIL, LINE FILTER
028R250009 COIL, DEGAUSS
0216731R2K COIL
021673100K COIL
0216731R0J COIL
021LA6150K COIL
02167D101K COIL
02A6A8A0A1 CORE, FERRITE
045013001J TRANS, HORIZONTAL DRIVE
JACK
!
!
!
1
UH
!
!
!
!
!
!
!
!
15 UH
100 UH
HF57T18.5*10*10
5013001
!
J801
066C130015 SOCKET, CRT
CVT3275-5102
SWITCHES
SW101
SW102
SW103
SW104
SW105
0504201T31 SWITCH, TACT
0504101T34 SWITCH, TACT
0504201T31 SWITCH, TACT
0504101T34 SWITCH, TACT
0504201T31 SWITCH, TACT
0504101T34 SWITCH, TACT
0504201T31 SWITCH, TACT
0504101T34 SWITCH, TACT
0504201T31 SWITCH, TACT
0504101T34 SWITCH, TACT
P.C.BOARD ASSEMBLIES
A3I058G01A PCB ASS'Y
A3I057G11A PCB ASS'Y
MISCELLANEOUS
0632400008 ANT, UNIT
120R614909 CORD, AC
1207614909 CORD, AC
068M82025A CORD, CONNECTOR
122E054401 CORD, JUMPER
122E044101 CORD, JUMPER
1022T45R72 FILTER, SAW
1011T4R504 FILTER, CERAMIC
1011T4R517 FILTER, CERAMIC
069W120019 CONNECTOR PCB SIDE
069W340018 CONNECTOR PCB SIDE
0697320039 CORD, UX CONNECTOR
069W420029 CONNECTOR PCB SIDE
0697260650 CONNECTOR PCB SIDE
069W320018 CONNECTOR PCB SIDE
SKHVBED010
EVQ21505R
SKHVBED010
EVQ21505R
SKHVBED010
EVQ21505R
SKHVBED010
EVQ21505R
SKHVBED010
EVQ21505R
or
or
or
or
or
DIODES
D001
D101
D103
D104
D125
D126
D127
D401
D402
D403
D404
D405
D407
D408
D410
D411
D422
D501
D502
D503
D504
D601
D602
D603
D94TA30013 DIODE, ZENER
D97U06R81B DIODE, ZENER
D97U06R81B DIODE, ZENER
D97U06R81B DIODE, ZENER
D1VT001330 DIODE, SILICON
D2WT0EM1C0 DIODE, SILICON
D2WT011E10 DIODE, SILICON
D94TA27011 DIODE, ZENER
D94TA11B11 DIODE, ZENER
D2WT011E10 DIODE, SILICON
D2WTAU02A0 DIODE, SILICON
D97U06R21B DIODE, ZENER
D2WTAU02A0 DIODE, SILICON
D2WTAU02A0 DIODE, SILICON
D2WTAU02A0 DIODE, SILICON
D2WTAU02A0 DIODE, SILICON
D2WTAU02A0 DIODE, SILICON
D2WTRM11C0 DOIDE, SILICON
D2WTRM11C0 DOIDE, SILICON
D2WTRM11C0 DOIDE, SILICON
D2WTRM11C0 DOIDE, SILICON
D1VT001330 DIODE, SILICON
D97U08R21B DIODE, ZENER
D1VT001330 DIODE, SILICON
HZ30-3L TD
MTZJ6.8B T-77
MTZJ6.8B T-77
MTZJ6.8B T-77
1SS133T-77
EM1C-EIC
!
11E1-EIC
PCB010
PCB110
TMX456A
TCX315A
!
!
HZ27-1L TD
HZ11B1L TD
11E1-EIC
!
!
ATC001
CD501
NXC0032-010010
0R614909
7614909
!
AU02A-EIC
MTZJ6.2B T-77
AU02A-EIC
AU02A-EIC
AU02A-EIC
AU02A-EIC
AU02A-EIC
RM11C-EIC
RM11C-EIC
RM11C-EIC
RM11C-EIC
1SS133T-77
MTZJ8.2B T-77
1SS133T-77
or
!
!
!
!
!
!
!
!
!
CD801
CD802
CD803
CF601
CF603
CF604
CP351
CP401
CP501
CP502
CP601
CP801
8M82025A
122E054401
122E044101
SAF45MFY220ZR
EFCT4R5YS5A
EFCT4R5MW5
TID-X02P-B2
TS-80P-04-V1
THL-P03P-B1
TV-50P-02-A1
TKC-M06X-A1
TS-80P-02-V1
!
!
!
J2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO.
DESCRIPTION
MISCELLANEOUS
CP806
069W010010 CONNECTOR PCB SIDE
067R005019 WIRE HOLDER
067R005019 WIRE HOLDER
067R104019 WIRE HOLDER
067R104019 WIRE HOLDER
027M062505 DY
005P-2100
51048-0510
51048-0510
51052-0400
51052-0400
7M062505
23706.3
CP802A
CP802B
CP803A
CP803B
DY801
F501
!
!
!
081PA6R302 FUSE
FB401
FH501
FH502
K001
K002
K003
043225010F TRANSFORMER, FLYBACK
06710T0006 HOLDER, FUSE
06710T0006 HOLDER, FUSE
129A000010 WEDGE
129A000010 WEDGE
129A000010 WEDGE
3225010F
EYF-52BC
EYF-52BC
8115529
8115529
8115529
!
!
!
MG801
MS501
OS101
RY101
SP351
TH501
TM101
TU001
V801
026A062704 MAGNET, CONVERGENCE
128B000018 SHEET
077Q014003 REMOTE RECEIVER
0560V20115 RELAY
29MMSTAR
23MICA
PIC-28143SY-2
ALKS321
SA04A05AWA
PTAD14K2-3R0Q141
R25-1127
NJH3021U268
A63AHC26X
8MHz
!
!
!
070C533016 SPEAKER
DF40A3R0Q0 DEGAUSS, ELEMENT
076R074180 TRANSMITTER
0145W00049 TUNER, VHF-UHF
0984250502 COLOR, PICTURE TUBE
1002T00801 CERAMIC OSILLATOR
100CT3R505 CRYSTAL HC-49/C
!
!
X101
X602
3.579545MHz
RESISTOR
RC................... CARBON RESISTOR
CAPACITORS
CC................... CERAMIC CAPACITOR
CE................... ALUMI ELECTROLYTIC CAPACITOR
CP................... POLYESTER CAPACITOR
CPP................. POLYPROPYLENE CAPACITOR
CPL.................. PLASTIC CAPACITOR
CMP................. METAL POLYESTER CAPACITOR
CMPL............... METAL PLASTIC CAPACITOR
CMPP.............. METAL POLYPROPYLENE CAPACITOR
J2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
M3I0-62G
A063519
SPEC.NO.
O/R NO.
Download from Www.Somanuals.com. All Manuals Search And Download.
|