Dukane Projector 8946 User Manual

Liquid Crystal Projector

Models 8805 & 8946

USER'S MANUAL

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Information

RF Interference

Safety Cautions

Precautions

WARNING

Please read this manual carefully before using your Dukane 8805/

8946 Projector and keep the manual handy for future reference.Your

serial number is located on the right side of your projector. Record it

here:

The Federal Communications Commission does not allow any

modifications or changes to the unit EXCEPT those specified

by Dukane Corporation AV Divisionin this manual. Failure to com-

ply with this government regulation could void your right to

operate this equipment. This equipment has been tested and

found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.These limits are designed

to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However,there is no guar-

antee that interference will not occur in a particular installa-

tion. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

CAUTION

To turn off main power, be sure to remove the plug from power

outlet.

The power outlet socket should be installed as near to the

equipment as possible, and should be easily accessible.

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PER-

SONNEL.

This symbol warns the user that uninsulated voltage within the

unit may be sufficient to cause electrical shock.Therefore, it is

dangerous to make any kind of contact with any part inside of

the unit.

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

This symbol alerts the user that important information con-

cerning the operation and maintenance of this unit has been

provided.

•

Consult the dealer or an experienced radio / TV technician for

help.

The information should be read carefully to avoid problems.

In UK, a BS approved power cable with moulded plug has a Black (five

Amps) fuse installed for use with this equipment. If a power cable is not

supplied with this equipment please contact your supplier.

WARNING

TO PREVENT FIRE OR SHOCK, DO NOT EXPOSETHIS UNITTO

RAIN OR MOISTURE.

Important Safeguards

DO NOT USETHIS UNIT’S GROUNDED PLUGWITH AN EXTEN-

SION CORD OR IN AN OUTLET UNLESS ALLTHE PRONGS CAN

BE FULLY INSERTED.

DO NOT OPENTHE CABINET.THERE ARE HIGH-VOLTAGE COM-

PONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALI-

FIED DUKANE SERVICE PERSONNEL.

These safety instructions are to ensure the long life of your projector

and to prevent fire and shock. Please read them carefully and heed all

warnings.

Installation

1. For best results, use your projector in a darkened room.

DOC Compliance Notice

2. Place the projector on a flat, level surface in a dry area away from

dust and moisture.

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

To avoid premature lamp failure, do not tilt the front of the projector

up or down by more than 75° from level. Tilting the front of the pro-

jector up or down from 15° to 75° might reduce lamp life by up to

25%.

Acoustic Noise Information Ordinance-3. GSGV:

The sound pressure level is less than 70 dB (A) according

to ISO 3744 or ISO 7779.

3. Do not place your projector in direct sunlight, near heaters or heat

radiating appliances.

4. Exposure to direct sunlight, smoke or steam can harm internal com-

ponents.

5. Handle your projector carefully. Dropping or jarring can damage in-

ternal components.

6. Do not place heavy objects on top of the projector.

7. If you wish to have the projector installed on the ceiling:

a. Do not attempt to install the projector yourself.

This label is on the side of the remote control.

CAUTION

b. The projector must be installed by qualified technicians in order

to ensure proper operation and reduce the risk of bodily injury.

Do not look into the laser pointer while it is on and do not

point the laser beam at a person. Serious injury could re-

sult.

c. In addition, the ceiling must be strong enough to support the

projector and the installation must be in accordance with any

local building codes.

d. Please consult your dealer for more information.

WARNING TO CALIFORNIA RESIDENTS:

Handling the cables supplied with this product, will expose you to

lead, a chemical known to the State of California to cause birth de-

fects or other reproductive harm. Wash hands after handling.

E-2

Download from Www.Somanuals.com. All Manuals Search And Download.

•

Allow a minimum of 90 seconds to elapse after turning off the pro-

jector. Then turn off the main power switch, disconnect the power

cable and allow 60 minutes to cool the projector before replacing

the lamp.

Fire and Shock Precautions

1. Ensure that there is sufficient ventilation and that vents are unob-

structed to prevent the build-up of heat inside your projector. Allow

at least 4 inches (10 cm) of space between your projector and a

wall.

2. Prevent foreign objects such as paper clips and bits of paper from

falling into your projector.

What's in the Box?

Make sure your box contains everything listed. If any pieces are miss-

ing, contact your dealer.

Do not attempt to retrieve any objects that might fall into your projec-

tor. Do not insert any metal objects such as a wire or screwdriver

into your projector. If something should fall into your projector, dis-

connect it immediately and have the object removed by a qualified

Dukane service personnel.

Please save the original box and packing materials if you ever need to

ship your 8805/8946 Projector.

Lens cap

3. Do not place any liquids on top of your projector.

4. Do not look into the lens while the projector is on. Serious damage

to your eyes could result.

5. Keep any items such as magnifying glass out of the light path of the

projector.The light being projected from the lens is extensive, there-

fore any kind of abnormal objects that can redirect light coming out

of the lens, can cause unpredictable outcome such as fire or injury

to the eyes.

Projector

Remote Control Cable

(7N520019)

6. Do not cover the lens with the supplied lens cap or equivalent while

the projector is on. Doing so can lead to melting of the cap and

possibly burning your hands due to the heat emitted from the light

output.

OFF

VIDEO

POWER

RGB

VIEWER

LASER

SELECT

ASPECT

FREEZE

HELP

REFORM

VOLUME

INTER

PIC

-M

NIFY

UTE

ZOOM

SLIDE

FOCUS

LDER

7. The projector is designed to operate on a power supply of 100-240

V 50/60 Hz AC. Ensure that your power supply fits this requirement

before attempting to use your projector.

SLIDE

LIST

Remote control

(7N900363)

Batteries

String (24C05051) and

rivet (24C04531)

8. Handle the power cable carefully and avoid excessive bending.

A damaged cord can cause electric shock or fire.

9. If the projector is not to be used for an extended period of time,

disconnect the plug from the power outlet.

10. Do not touch the power plug during a thunderstorm. Doing so can

cause electrical shock or fire.

CAUTION

1. Do not try to touch the ventilation outlet on the front as it can be-

come heated while the projector is turned on.

Power cable

(US: 7N080204)

(EU: 7N080008)

USB cable

(7N520013)

RGB signal cable

(7N520032)

2. Do no use the tilt-foot for purposes other than originally intended.

Misuses such as gripping the tilt-foot or hanging on the wall can

cause damage to the projector.

Quick

Connect

3. Enable High-Speed Fan mode if you continue to use the projector

for consecutive days. (From the Advanced menu, select [Projector

Options] → [Setup] → [Page 4] → [High Speed Fan Mode].)

Guide

User's

Manual

4. Do not unplug the power cable from the wall outlet under any one of

the following circumstances.

CD-ROM

Projector User Supportware

(7N950432)

Doing so can cause damage to the projector:

While the Hour Glass icon appears.

While the message "Please wait a moment." appears.This mes-

sage will be displayed after the projector is turned off.

8805 only

USB mouse (7N960151)

For North America only

Registration card

Limited warranty

While the cooling fans are running.(The cooling fans continue to

work for 90 seconds after the projector is turned off).

5. Do not eject the PC card or LAN card while its data is being accessed.

Doing so can damage your PC card or LAN card data.

For Europe only

Guarantee policy

6. Do not hold the lens part with your fingers. Doing so could pinch

fingers or hands causing injury.

Lamp Replacement

•

To replace the lamp, follow all instructions provided on page E-55.

Be sure to replace the lamp when the message "The lamp has

reached the end of its usable life. Please replace the lamp."

appears. If you continue to use the lamp after the lamp has reached

the end of its usable life, the lamp bulb may shatter, and pieces of

glass may be scattered in the lamp case. Do not touch them as the

pieces of glass may cause injury.

If this happens, contact your Dukane dealer for lamp replacement.

E-3

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

Selecting Overscan Percentage .............................................................................. E-41

Selecting Video Filter Level .................................................................................... E-41

Selecting Noise Reduction Level ............................................................................ E-41

Signal Type ............................................................................................................ E-41

Picture Management .................................................................................................. E-41

User Adjust (when using User 1 to 4) .................................................................... E-41

Selecting Gamma Correction Mode ................................................................ E-42

Selecting Color Correction ............................................................................. E-42

Adjusting Color Temperature and White Balance ............................................ E-42

Selecting Base Setting .................................................................................... E-42

Projector Options ...................................................................................................... E-42

Using 3D Reform ................................................................................................... E-42

Cornerstone ................................................................................................... E-42

Keystone ........................................................................................................ E-42

Using Adapting Color Correction ........................................................................... E-43

Menu [Page1] ........................................................................................................ E-45

Selecting Menu Language/Selecting Menu Mode/Customizing the Menu/Select-

ing Projecting Pointer Icon & Mouse Icon/Selecting Menu Display Time

Menu [Page 2] ....................................................................................................... E-45

Turning On/Off Source Display / Turning On/Off Message / Selecting Menu Color

Setup [Page 1] ....................................................................................................... E-46

Selecting Projector Orientation/Selecting a Color or Logo for Background/Setting

RGB 1 or 2 for RGB OUT/Setting Closed Caption

Setup [Page 2] ....................................................................................................... E-46

Setting Viewer Options/Selecting Capture Options/Setting Mouse Button and Sen-

sitivity/Selecting Operation Mode

Setup [Page 3] ....................................................................................................... E-47

Selecting Signal Format [Signal Select]

Setup [Page 4] ....................................................................................................... E-47

Enabling Auto Adjust/Enabling Auto Start/Enabling Power Management/Enabling

Power Off Confirmation/Enabling Horizontal and Vertical Keystone Correction Save

/Enabling High Speed Fan Mode/Selecting Built-in Speakers/Enabling Idle Mode/

Resetting the Filter Usage Hours

Setup [Page 5] ....................................................................................................... E-48

Remote Sensor/S-Video Mode Select

Setup [Page 6] ....................................................................................................... E-48

Selecting Communication Speed/Selecting Default Source/Disabling the Cabinet

Buttons

Selecting Lamp Mode and Lamp Type ................................................................... E-48

Selecting Aspect Ratio and Position for Screen ..................................................... E-49

Selecting Auto Functions ....................................................................................... E-49

Setting LAN Mode ..................................................................................................... E-50

IP Address ............................................................................................................. E-50

Network Type ......................................................................................................... E-50

WEP ....................................................................................................................... E-51

Mail ........................................................................................................................ E-51

Status .................................................................................................................... E-52

Setting a Password .................................................................................................... E-52

Security ..................................................................................................................... E-53

Tools .......................................................................................................................... E-54

Using Sleep Timer/Using Capture/Using PC Card Files/Using ChalkBoard

Help ........................................................................................................................... E-54

Contents ................................................................................................................ E-54

Information ............................................................................................................ E-54

Returning to Factory Default ...................................................................................... E-54

Important Information ..................................................... E-2

Safety Cautions ............................................................................................................... E-2

What's in the Box? .......................................................................................................... E-3

INTRODUCTION .............................................................. E-5

Introduction to the Projector ........................................................................................... E-5

Part Names of the Projector ............................................................................................ E-6

Attaching the lens cap ................................................................................................. E-6

Carrying the Projector ................................................................................................. E-6

Top Features ................................................................................................................ E-7

Terminal Panel Features ............................................................................................... E-8

Part Names of the Remote Control .............................................................................. E-9

Battery Installation ................................................................................................. E-11

Remote Control Precautions .................................................................................. E-11

Operating Range for Wireless Remote Control ...................................................... E-11

Using the Remote Control in Wired Operation ....................................................... E-11

INSTALLATION AND CONNECTIONS ....................................... E-12

Setting Up the Screen and the Projector ....................................................................... E-12

Selecting a Location .................................................................................................. E-12

Throw Distance and Screen Size ............................................................................... E-13

Making Connections ...................................................................................................... E-14

When Viewing a DVI Digital Signal ............................................................................ E-14

Connecting Your PC or Macintosh Computer ............................................................ E-14

To connect SCART output (RGB) ............................................................................... E-15

Connecting an External Monitor ................................................................................ E-15

Connecting Your DVD Player ..................................................................................... E-16

Connecting Your VCR or Laser Disc Player ............................................................... E-17

Connecting the Supplied Power Cable ....................................................................... E-17

PROJECTING AN IMAGE (BASIC OPERATION) ........................... E-18

Turning on the Projector ................................................................................................ E-18

Selecting a Source ......................................................................................................... E-19

Adjusting the Picture Size and Position ......................................................................... E-19

Correcting the Horizontal and Vertical Keystone Distortion (3D Reform) ...................... E-20

Optimizing RGB Picture Automatically .......................................................................... E-22

Turning Up or Down Volume ......................................................................................... E-22

Using the Laser Pointer ................................................................................................. E-22

Setting the function switch ............................................................................................ E-23

Turning off the Projector ............................................................................................... E-23

CONVENIENT FEATURES ................................................... E-24

Using the Remote Mouse Function ............................................................................... E-24

Connecting to your computer for the remote mouse function ................................... E-24

When using the USB Port .......................................................................................... E-24

Switching operation mode between computer and projector ..................................... E-24

Auto 3D Reform ............................................................................................................ E-25

Turning Off the Image and Sound .................................................................................. E-27

Freezing a Picture .......................................................................................................... E-27

Using a Pointer .............................................................................................................. E-27

Enlarging and Moving a Picture ..................................................................................... E-27

Getting the On-line Help ................................................................................................ E-27

Using a USB Mouse ...................................................................................................... E-28

Using the USB HUB Function ........................................................................................ E-28

Changing Background Logo .......................................................................................... E-29

Making Freehand Drawings on a Projected Image (ChalkBoard) ................................... E-29

USB Memory Device or USB Memory Card Reader Support ......................................... E-29

MAINTENANCE ............................................................. E-55

Replacing the Lamp ...................................................................................................... E-55

Cleaning ........................................................................................................................ E-56

Cleaning or Replacing the Filter ................................................................................. E-56

Cleaning the Cabinet and the Lens ............................................................................. E-56

USING THE VIEWER ........................................................ E-30

Making the Most out of the Viewer Function ................................................................. E-30

Operating the Viewer Function from the Projector (playback) ....................................... E-31

Projecting slides (Viewer) .......................................................................................... E-31

Auto Play Mode ......................................................................................................... E-32

Switching to Slides Directly from Other Input Modes ................................................ E-32

Viewing Digital Images .............................................................................................. E-32

Storing Images Displayed on the Projector on the PC card (Capture) ....................... E-32

Deleting Captured Images ......................................................................................... E-33

Using the PC Card Files Fucntion (PC Card Files) ...................................................... E-33

TROUBLESHOOTING ........................................................ E-57

Power Indicator ............................................................................................................. E-57

Status Indicator ............................................................................................................. E-57

Lamp Indicator .............................................................................................................. E-57

Common Problems & Solutions .................................................................................... E-58

SPECIFICATIONS ........................................................... E-60

USING ON-SCREEN MENU ................................................. E-34

Basic Menu Operation ................................................................................................... E-34

Using the Menus ....................................................................................................... E-34

Customizing the Menu ............................................................................................... E-34

Menu tree ...................................................................................................................... E-35

Menu Elements ............................................................................................................. E-38

Entering Alphanumeric Characters by Using the Menu .............................................. E-39

Menu Descriptions & Functions .................................................................................... E-39

Source Select ............................................................................................................ E-39

RGB/Video/S-Video/DVI (DIGITAL)/Viewer/LAN/Entry List

APPENDIX ................................................................... E-62

Cabinet Dimensions ...................................................................................................... E-62

Pin Assignments of D-Sub RGB Input Connector .......................................................... E-62

Compatible Input Signal List ......................................................................................... E-63

PC Control Codes and Cable Connection ....................................................................... E-64

PC Control Connector (D-SUB 9P) ................................................................................ E-64

Using Software Keyboard .............................................................................................. E-64

Operation Using an HTTP Browser ................................................................................ E-65

TravelCare Guide ........................................................................................................... E-66

Picture ....................................................................................................................... E-40

Sound ........................................................................................................................ E-40

Image Options ........................................................................................................... E-40

Selecting Aspect Ratio ........................................................................................... E-40

Masking Unwanted Area (Blanking) ....................................................................... E-41

Adjusting Position and Clock ................................................................................. E-41

Selecting Resolution .............................................................................................. E-41

E-4

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

•

Exclusive Advanced AccuBlend intelligent pixel blending tech-

nology - an extremely accurate image compression technology - of-

fers a crisp image with UXGA (1600

1200) resolution*³.

Introduction to the Projector

This section introduces you to your new 8805/8946 Projector and

describes the features and controls.

Supports most IBM VGA, SVGA, XGA, SXGA/UXGA(with Advanced

AccuBlend)*³, Macintosh, component signal (YCbCr/ YPbPr) or any

other RGB signals within a horizontal frequency range of 24 to 100

kHz and a vertical frequency range of 48 to 120 Hz. This includes

NTSC, PAL, PAL-N, PAL-M, PAL60, SECAM and NTSC4.43 stan-

dard video signals.

Congratulations on Your Purchase of The 8946/

8805 Projector

The 8805/8946 is one of the very best projectors available today.

The 8805/8946 enables you to project precise images up to 500

inches across (measured diagonally) from your PC or Macintosh com-

puter (desktop or notebook), VCR, DVD player, document camera, a

laser disc player or Viewer.

A UXGA (1600

1200) and SXGA (1280

1024) image are dis-

played with Advanced AccuBlend.

You can use the projector on a tabletop or cart, you can use the projec-

tor to project images from behind the screen, and the projector can be

permanently mounted on a ceiling*¹. The remote control can be used

wirelessly.

NOTE: Composite video standards are as follows:

NTSC: U.S. TV standard for video in U.S. and Canada.

PAL: TV standard used in Western Europe.

PAL-N: TV standard used in Argentine, Paraguay and Uruguay.

PAL-M: TV standard used in Brazil.

PAL60: TV standard used for NTSC playback on PAL TVs.

SECAM: TV standard used in France and Eastern Europe.

NTSC4.43: TV standard used in Middle East countries.

Do not attempt to mount the projector on a ceiling yourself.

The projector must be installed by qualified technicians in order

to ensure proper operation and reduce the risk of bodily injury.

In addition, the ceiling must be strong enough to support the pro-

jector and the installation must be in accordance with any local

building codes. Please consult your dealer for more information.

•

The supplied remote control can be used without a cable, and you

can even use the remote control to operate your PC's mouse wirelessly

from across the room with the built-in remote mouse function.

•

You can control the projector with a PC using the PC Control port.

USB port allows USB mouse operation*⁴.

Features you'll enjoy:

•

3D Reform enhanced keystone correction that allows not only hori-

zontal and vertical access but diagonal adjustments.

The USB ports meet the USB1.1 specification.

•

The contemporary cabinet design is light, compact, easy to carry,

and complements any office, boardroom or auditorium.

•

Wireless*²or wired networking access provides easy and effective

presentation delivery.

Nine pointers are available for your presentation.

A wireless LAN card is required.The optional wireless LAN

card is available. (SWL-2100N-N )

∗

About this user's manual

•

Safety protect by Password and Security functions

The fastest way to get started is to take your time and do ev-

erything right the first time. Take a few minutes now to review

the user's manual. This may save you time later on. At the be-

ginning of each section of the manual you'll find an overview. If

the section doesn't apply, you can skip it.

Password and Security features prevent the projector from being used

by unauthorized individuals.

Password prevents unauthorized individuals from changing projector

settings or adjustments. Security offers complete protection by using

your PC card as a protect key so that the projector will not project a

signal without insertion of the registered PC card and unauthorized

use can be discouraged.

•

Picture Management enables users to adjust individual color settings

to their preferences.

Eco-mode extends lamp life and reduces total cost of ownership.

Standard lamp and optional longer life lamp

•

Power zoom and power focus standard lens provide easy adjust-

ment.

•

Automatic lens focus provides extreme ease of use

Automatic Wall Color Correction allows for quick adaptive color cor-

rection on textured or painted walls and in applications where the

display is other than screen material. With the built-in image sensor,

the projector adjusts the colors for screen sizes between 40" and

150" diagonally.

•

Variable audio out control via projector

The built-inViewer allows you to start your presentation even when a

PC is not available at the site.

•

A high-bright 300 watt DC lamp (240W Eco mode). (8946)

A high-bright 275 watt DC lamp (220W Eco mode). (8805)

•

The Standby mode reduces standby power consumption significantly.

The supplied wireless remote control that operates the projector from

any angle.

•

The image can be projected between 25 and 500 inches (measured

diagonally).

•

The "Capture" enables you to capture the current projected image.

An image can be projected from in front or behind a screen, and the

projector can even be installed on the ceiling.

E-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Part Names of the Projector

Remote Sensor (See page E-11 and -48)

Controls (See page E-7)

Image Sensor

For Auto Focus and Auto Wall Color

Correction. (See page E-49)

Remote Sensor (See page E-11 and -48)

Built-in Security Slot ( )*

Lens

Ventilation (inlet)

Carrying Handle

Adjustable Tilt Foot Lever

(See page E-19)

Adjustable Tilt Foot

(See page E-19)

Lens Cap

Adjustable Tilt Foot Lever

(See page E-19)

Ventilation (outlet)

Heated air is exhausted from here

Adjustable Tilt Foot (See page E-19)

This security slot supports the MicroSaver^®Security System. MicroSaver^®is a registered trademark of Kensington Microware Inc. The logo is

trademarked and owned by Kensington Microware Inc.

Lamp Cover (See page E-55)

PC Card Slot 1

PC Card Slot 2

Remote Sensor (See page E-11 and -48)

Filter Cover (inlet)

REM

PC Card Eject Button

)

E/H

(

/MO

DIO

B/C

G/Y

DIO

AC IN

Remote Sensor

(See page E-11 and -48)

DIO

L/MONO

DIO

L/MON

DIO

S-

AC Input

Stereo Speaker (5W)

Main Power Switch

Connect the supplied power cable's three-

pin plug here, and plug the other end into

an active wall outlet. (See page E-17)

When you plug the supplied power cable into

an active wall outlet and turn on the Main

Power switch, the POWER indicator turns

orange and the projector is in standby mode.

(See page E-18)

Carrying the Projector

Attaching the lens cap

Always carry your projector by the handle.

To attach the lens cap to the bottom with the supplied string and rivet:

Ensure that the power cable and any other cables connecting to video

sources are disconnected before moving the projector.

When moving the projector or when it is not in use, cover the lens with

the lens cap.

1. Thread the string through the

hole on the lens cap and then

tie a knot in the string.

2. Use the rivet to attach the

string to the bottom of the

projector.

E-6

Download from Www.Somanuals.com. All Manuals Search And Download.

11. SELECT ꢀꢁꢂꢃ (+) (–) / Volume Buttons

ꢀꢁ : Use these buttons to select the menu of the item you wish to

adjust. When no menus appear, these buttons work as a vol-

ume control.

Top Features

11 10

ꢂꢃ : Use these buttons to change the level of a selected menu item.

A press of the ꢃ button executes the selection.When the menus

or the Viewer tool bar is not displayed, these buttons can be

used to select a slide, or to move the cursor in Folder List or

Slide List.

When the pointer is displayed, these ꢀꢁꢂꢃ buttons move the pointer.

12. ENTER Button

Executes your menu selection and activates items selected from the

menu.

12 13 14

)

13. CANCEL Button

Press this button to exit "Menus". Press this button to return the ad-

justments to the last condition while you are in the adjustment or

setting menu.

1. POWER Button (ON / STAND BY)(

Use this button to turn the power on and off when the main power is

supplied and the projector is in standby mode.

14. PC CARD Access Indicator 1/2

Lights while accessing a PC card.

NOTE: To turn on or off the projector, press and hold this button for a mini-

mum of two seconds.

2. POWER Indicator

When this indicator is green, the projector is on; when this indicator

is orange, it is in standby or idle mode. See the Power Indicator sec-

tion on page E-57 for more details.

3. STATUS Indicator

If this light blinks red rapidly, it indicates that an error has occurred,

the lamp cover is not attached properly or the projector has over-

heated.If this light remains orange, it indicates that you have pressed

a cabinet key while the Control Panel Key Lock is enabled. See the

Status Indicator section on page E-57 for more details.

4. LAMP Indicator

If this light blinks red rapidly, it's warning you that the lamp has reached

the end of its usable life. After this light appears, replace the lamp as

soon as possible (See page E-55). If this is lit green continually, it

indicates that the lamp mode is set to Eco. See the Lamp Indicator

section on page E-57 for more details.

5. SOURCE Button

Use this button to select a video source such as a PC, VCR, DVD

player, Viewer (PC card), or LAN.

Press and release this button quickly to display the Source List.

Each time this button is pressed for a minimum of ONE second, the

input source will change as follows:

RGB1 → RGB2 → Video → S-Video → DVI (DIGITAL) → Viewer → RGB1 → ...

If no input signal is present, the input will be skipped.

6. AUTO ADJUST Button

Use this button to adjust Position-H/V and Pixel Clock/Phase for an

optimal picture (See page E-22).Also press and hold this button for a

minimum of 2 seconds to enable the Auto Focus or Auto Wall Color

Correction function (See page E-49).

7. 3D REFORM Button

Press this button to enter 3D Reform mode to correct the keystone

(trapezoidal) distortion, and make the image square.

8. ZOOM Button (+/–)

Zoom the lens in and out.

9. FOCUS Button (+/–)

Adjust the lens focus.

10. MENU Button

Displays the menu.

E-7

Download from Www.Somanuals.com. All Manuals Search And Download.

5. S-VIDEO IN Connector (Mini DIN 4 Pin)

Here is where you connect the S-Video input from an external source

like a VCR.

Terminal Panel Features

9 10 13

NOTE: S-Video provides more vivid color and higher resolution than the tra-

ditional composite video format.

S-VIDEO AUDIO Input Jacks R/L (RCA)

These are your left and right channel audio inputs for stereo sound

from an S-Video source.

6. VIDEO IN Connector (RCA)

Connect a VCR, DVD player, laser disc player, or document camera

here to project video.

VIDEO AUDIO Input Jacks R/L (RCA)

These are your left and right channel audio inputs for stereo sound

from a Video source.

1. RGB1 IN / Component Input Connector (Mini D-Sub 15 Pin)

Connect your computer or other analog RGB equipment such as IBM

compatible or Macintosh computers. Use the supplied RGB cable to

connect to your computer. This also serves as a component input

connector that allows you to connect a component video output of

component equipment such as a DVD player. This connector also

supports SCART output signal. See page E-15 for more details.

7. AUDIO OUT Jacks R/L (RCA)

You can use this connector to output sound from the currently se-

lected input source (RGB 1, RGB 2, DVI (DIGITAL),Video or S-Video).

Output sound level can be adjusted in accordance with the sound

level of the internal speaker.

RGB1 AUDIO Input Mini Jack (Stereo Mini)

8. USB Port (MOUSE/HUB) [Type A]

This is where you connect the audio output from your computer or

DVD player when connected to the RGB1 input.A commercially avail-

able audio cable is required.

Connect a USB mouse.You can operate the menu or Viewer with the

USB mouse via this port.

•

A USB-supported scanner or PC peripheral can be connected

to this port. (USB Hub Function)

2. RGB2 IN / Component Input Connectors (BNC)

Connect R,G,B,H (Horizontal sync) and V (Vertical sync) outputs of

external equipment.

9. USB Port (PC) [Type B]

Connect this port to the USB port (type A) of your PC using the sup-

plied USB cable.You can operate your computer's mouse functions

from the remote control. This port also serves as a PC Control port

by using Dynamic Image Utility 2.0 included on the supplied CD-

ROM.

If using a component with a combined sync (SYNC) output, connect

it to the H/V terminal.

When using luminance and color-difference signals of HDTV and DVD,

connect Pr/Cr to the R,Y to the G and Pb/Cb to the B input of the

projector.

10. REMOTE (Mini Jack)

Connect your remote control cable here for wired operation.

NOTE: The RGB IN 2 does not support Plug & Play.

RGB2 AUDIO IN Mini Jack (Stereo Mini)

11. PC CONTROL Port (D-Sub 9 Pin)

This is where you connect audio output from your computer or DVD

player connected to the RGB2 input. A commercially available audio

cable is required.

Use this port to connect your PC to control your projector via a serial

cable. This enables you to use your PC and serial communication

protocol to control the projector. A commercially available RS232C

cross cable is required to use this port.You can also control the pro-

jector by using Dynamic Image Utility 2.0 included on the supplied

CD-ROM.

To do so you must first have Dynamic Image Utility 2.0 installed on

your PC.If you are writing your own program, typical PC control codes

are on page E-64.

3. DVI IN Connector (24 pin)

This connector can be used to accept a digital signal output from a

computer or other sources with a DVI connector.

DVI AUDIO Input Mini Jack (Stereo Mini)

This is where you connect the audio output from your computer when

connected to the DVI input. A commercially available audio cable is

required.

12. PC CARD Slot 1/2

Insert a PC card, commercially available LAN card or optional

wireless LAN card here.

There are two slots: Slot 1 and Slot 2.

4. RGB OUT Connector (Mini D-Sub 15 Pin)

You can use this connector to loop your computer image to an exter-

nal monitor from the RGB 1 or 2 input source.

The RGB analog signal set on RGBOUT Terminal is output during

idle mode. See pages E-15 and -46.

NOTE: A dummy card is inserted into each slot at the time of shipment. First

remove the dummy cards before use.

13. PC CARD Eject Button 1/2

Press to eject a PC card partially. Each slot has its own eject button:

1 and 2.

RGB AUDIO OUT Mini Jack (Stereo Mini)

Connect an additional audio equipment here to listen to audio com-

ing from your computer connected to RGB1, RGB2 or DVI input.

Note that there is no audio output from this jack during Standby and

Idle.

E-8

Download from Www.Somanuals.com. All Manuals Search And Download.

9. VIEWER Button

Press this button to select the Viewer source.

Part Names of the Remote Control

NOTE: If you are using a Macintosh computer, you can click either the right-click

or left-click button to activate the mouse.

10. AUTO ADJ Button

Use this button to adjust an RGB source for an optimal picture. Also

press and hold this button for a minimum of 2 seconds to enable the

Auto Focus or Auto Wall Color Correction function. See page E-20 or

-22.

1. Infrared Transmitter

T E

I C - M

Direct the remote control toward

the remote sensor on the projec-

tor cabinet.

R E F O R M

3 D

E E

11. LASER Button

S E L E C T

Press and hold this button to activate the laser pointer.When lit, you

can use the laser to draw your audience's attention to a red dot that

you can place on any object.

L A S E R

2. LASER Pointer

Beams a laser light when the LA-

SER button is pressed.

E R

V I E W

R G B

O N

A U T O A D J .

E R

P O W

V I D E O

O F F

12. MENU Button

Displays the menu for various settings and adjustments.

3. Remote Jack

Connect your remote control

cable here for wired operation.

13. SELECT ꢀꢁꢂꢃ (Mouse) Button

When you are in the Computer mode, these buttons work as a com-

puter mouse.

When you are in the Projector mode, which is indicated by lighting

the PJ button. See page E-24.

OFF

ꢀꢁ : Use these buttons to select the menu of the item you wish

to adjust.

POWER

VIDEO

RGB

VIEWER

LASER

ꢂꢃ : Use these buttons to change the level of a selected menu

item. A press of the ꢃ button executes the selection.

When the pointer is displayed, these ꢀꢁꢂꢃ buttons move the pointer.

When the pointer is not displayed, these ꢀꢁꢂꢃ buttons are for adjust-

ing the image.

AUTO ADJ.

14. ENTER (Left Click) Button

SELECT

When you are in the Computer mode, this button works as the mouse

left button. When this button is pressed and held for a minimum of 2

seconds, the drag mode is set. When you are in the Projector mode,

which is indicated by lighting the PJ button: Use this button to enter

your menu selection. It works the same way as the ENTER button on

the cabinet. See page E-7.

ASPECT FREEZE 3D REFORM

15. CANCEL (Right Click) Button

When you are in the Computer mode, this button works as the mouse

right button. When you are in the Projector mode, which is indicated

by lighting the PJ button: Press this button to exit the Menus. It works

the same way as the CANCEL button on the cabinet. See page E-7.

HELP

POINTER PIC-MUTE

SLIDE

VOLUME MAGNIFY

ZOOM

FOCUS

FOLDER

SLIDE

16. PJ Button

Press this button to switch the SELECT, CANCEL, and ENTER but-

tons between the Projector mode (lit red) and the Computer mode.

Press this button or any one of the POWER ON/OFF, MENU, AS-

PECT, 3D REFORM, HELP, POINTER, MAGNIFY,VIEWER, FOLDER

LIST or SLIDE LIST buttons to switch to the Projector mode and the

PJ button lights red.To switch back to the Computer mode, press the

PJ button again. See page E-24.

LIST

4. LED

Flashes when any button is pressed.

17. ASPECT Button

5. POWER ON Button

Press this button to display the Aspect Ratio select screen.See page

E-40.

When the main power is on, you can use this button to turn your

projector on.

NOTE: To turn on the projector, press and hold the POWER ON button for a

minimum of two seconds.

18. FREEZE Button

This button will freeze a picture. Press again to resume motion.

6. POWER OFF Button

You can use this button to turn your projector off.

19. 3D REFORM Button

Press this button to enter 3D Reform to correct the keystone (trap-

ezoidal) distortion, and make the image square. See page E-20.

NOTE: To turn off the projector, press and hold the POWER OFF button for a

minimum of two seconds.

20. HELP Button

7. VIDEO Button

Provides the online help or the set information.

Press this button to toggle between Video and S-Video inputs.

21. POINTER Button

8. RGB Button

Press this button to display one of the nine pointers; press again to

hide the pointer.You can move your pointer icon to the area you want

on the screen using the Select ꢀꢁꢂꢃ button. See page E-27.

Press this button to select RGB 1, RGB 2 or DVI (DIGITAL) inputs.

Each time this button is pressed, the input source will change as

follows:

RGB 1 → RGB 2 → DVI (DIGITAL) → RGB 1 → ...

E-9

Download from Www.Somanuals.com. All Manuals Search And Download.

OFF

POWER

RGB

VIDEO

VIEWER

LASER

AUTO ADJ.

SELECT

ASPECT FREEZE 3D REFORM

HELP

POINTER PIC-MUTE

SLIDE

VOLUME MAGNIFY

ZOOM

FOCUS

FOLDER

SLIDE

LIST

22. PICTURE MUTE Button

This button turns off the image and sound for a short period of time.

Press again to restore the image and sound.

NOTE: When the menu is displayed, a press of this button mutes an image

and sound without turning off the menu.

23.VOLUME (+)(–) Button

Press (+) to increase the volume and (–) to decrease it.

24. MAGNIFY (+)(–) Button

Use this button to adjust the image size up to 400%.When the pointer

is displayed, the image is magnified about the center of the pointer.

When the image is magnified, the pointer is changed to the magnify-

ing icon.

When the pointer is not displayed, the image is magnified about the

center of the screen. See page E-27.

25. ZOOM (+)(–) Button

Zoom the lens in and out.

26. FOCUS (+)(–) Button

Adjust the lens focus.

27. SLIDE (+)(–) Button

Press (+) to select the next folder or slide and (–) to select the previ-

ous folder or slide. See page E-31.

28. FOLDER LIST Button

Press this button to select Viewer source to display a list of folders

included in a PC card. See page E-31.

29. SLIDE LIST Button

Press this button to select Viewer source to display a list of slides

included in a PC card. See page E-31.

NOTE: The default is the Computer mode, which allows you to use the SELECT,

CANCEL, and ENTER buttons as your computer mouse. When the POWER ON/

OFF, MENU, ASPECT, 3D REFORM, HELP, POINTER, MAGNIFY, VIEWER, FOLDER

LIST, or SLIDE LIST button is pressed, the PJ button lights red to indicate that

you are in the Projector mode. If no buttons are pressed within 60 seconds, the

light goes out and the Projector mode is canceled.

E-10

Download from Www.Somanuals.com. All Manuals Search And Download.

Battery Installation

Remote Control Precautions

1. Press firmly and slide the battery cover off.

•

Handle the remote control carefully.

If the remote control gets wet, wipe it dry immediately.

Avoid excessive heat and humidity.

If you will not be using the remote control for a long time, remove the

batteries.

•

Do not place the batteries upside down.

Do not use new and old batteries together, or use different types of

batteries together

2. Remove both old batteries and install new ones (AA). Ensure that

you have the batteries' polarity (+/-) aligned correctly.

Operating Range for Wireless Remote Control

Remote sensor on the

projector cabinet

7m/22 feet

3. Slip the cover back over the batteries until it snaps into place. Do not

mix different types of batteries or new and old batteries.

7m/22 feet

Remote control

Remote sensor on the

projector cabinet

•

The infrared signal operates by line-of-sight up to a distance of about

22 feet/7 m and within a 60-degree angle of the remote sensor on the

projector cabinet.

Note on Remote Control Operation:

If you press and hold the SELECT ꢀꢁꢂꢃ button while installing new

batteries, the remote control may fail to work properly.

Should this happen, remove the batteries and then install them again

without touching the SELECT button.

The projector will not respond if there are objects between the re-

mote control and the sensor, or if strong light falls on the sensor.

Weak batteries will also prevent the remote control from properly

operating the projector.

Using the Remote Control in Wired Operation

Connect one end of the supplied remote cable to the REMOTE mini

jack and the other end to the remote jack on the remote control.

REMOTE

OFF

POWER

RGB

VIDEO

AUTO ADJ.

VIEWER

LASER

HELP

SLIDE

ZOOM

FOCUS

FOLDER

SLIDE

LIST

E-11

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS

This section describes how to set up your projector and how to connect video and audio sources.

Your projector is simple to set up and use.

But before you get started, you must first:

z Set up a screen and the projector.

x Connect your computer or video equip-

ment to the projector. See page

E-14 – 17.

c Connect the supplied power cable. See

page E-17.

NOTE: Ensure that the power cable and any

other cables are disconnected before moving

the projector. When moving the projector or

when it is not in use, cover the lens with the

lens cap.

To the wall outlet.

Setting Up the Screen and the Projector

Selecting a Location

The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 25" (0.64 m)

measured diagonally when the projector is roughly 39.4 inches (1.0 m) from the wall or screen.The largest the image can be is 500" (12.7 m) when

the projector is about 614.2 inches (15.6 m) from the wall or screen. Use the drawing below as a guide.

Screen size (Unit: cm/inch)

609.6(W)X457.2(H)/240(W)X180(H)

487.7(W)X365.8(H)/192(W)X144(H)

406.4(W)X304.8(H)/160(W)X120(H)

Screen Size

365.8(W)X274.3(H)/144(W)X108(H)

300"

240"

304.8(W)X228.6(H)/120(W)X90(H)

200"

243.8(W)X182.9(H)/96(W)X72(H)

180"

203.2(W)X152.4(H)/80(W)X60(H)

150"

162.6(W)X121.9(H)/64(W)X48(H)

120"

121.9(W)X91.4(H)/48(W)X36(H)

100"

81.3(W)X61.0(H)/32(W)X24(H)

61.0(W)X45.7(H)/24(W)X18(H)

TELE: 50.8(W)X38.1(H)/20(W)X15(H)

80"

60"

40"

30"

Lens center

25"

1.0

1.1

1.4

2.1

2.8

3.5

6.4

4.3

5.3

7.1

8.5

10.6

Distance (Unit: m)

E-12

Download from Www.Somanuals.com. All Manuals Search And Download.

Throw Distance and Screen Size

The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation.

Distance Chart

Screen Size

Diagonal

inch

Width

inch

120

144

160

168

192

209

216

240

280

320

360

400

Height

inch

Wide – Tele

inch

Wide – Tele

degree

Screen Width

inch

8.0

9.0

–––

35.1

39.6

47.8

64.4

–––

14.4

14.2

14.0

13.9

13.8

13.7

10.7

10.5

10.4

10.3

–––

12.0

18.0

20.0

22.0

24.0

25.0

27.0

30.0

36.0

45.0

54.0

60.0

63.0

72.0

78.0

81.0

90.0

105.0

120.0

135.0

150.0

47.4

72.1

97.6

Screen Diagonal

80.7

86.9

96.8

109.2

117.5

130.8

137.4

147.4

164.0

197.2

246.9

296.7

329.9

346.5

396.3

431.1

446.0

495.8

578.7

–––

Screen Height

Screen center

101.7

109.1

121.4

146.1

183.1

220.1

244.8

257.1

294.1

320.0

331.1

368.1

429.8

491.5

553.2

614.8

100

120

150

180

200

210

240

261

270

300

350

400

450

500

(B)

108

120

126

144

157

162

180

210

240

270

300

Screen Bottom

Lens Center

Throw Angle (Ͱ)

–––

Throw Distance (C)

Screen Size

Diagonal

635

Width

508

610

813

Height

381

457

610

Wide – Tele

degree

191

229

305

457

511

549

610

640

–––

891

1005

1215

1636

2479

2774

2985

3322

3490

3743

4165

5007

6272

7536

8379

8800

–––

14.4

14.2

14.0

13.9

13.8

13.7

10.7

10.5

10.4

10.3

–––

762

B = Vertical distance between lens center and screen center

C = Throw distance

α = Throw angle

1016

1524

1702

1829

2032

2134

2286

2540

3048

3810

4572

5080

5334

6096

6629

6858

7620

8890

10160

11430

12700

1204

1831

2050

2207

2458

2583

2771

3084

3711

4651

5591

6217

6531

1219

1361

1463

1626

1707

1829

2032

2438

3048

3658

4064

4267

4877

5304

5486

6096

7112

8128

9144

10160

914

1021

1097

1219

1280

1372

1524

1829

2286

2743

3048

3200

3658

3978

4115

4572

5334

6096

6858

7620

NOTE: Distances may vary +/-5%.

686

762

914

1143

1372

1524

1600

1829

1989

2057

2286

2667

3048

3429

3810

7471 - 10064

8129 - 10949

8410 - 11328

9350 - 12593

10917 - 14700

12484

14050

15617

–––

WARNING

Reflecting the Image

Installing your projector on the ceiling must be done by a quali-

Using a mirror to reflect your projector's image enables you to enjoy a

much larger image. Contact your Dukane dealer if you need a mirror. If

you're using a mirror and your image is inverted, use the MENU and

SELECT buttons on your projector cabinet or ꢀꢁ buttons on your re-

mote control to correct the orientation. (See page E-46.)

fied technician. Contact your Dukane dealer for more information.

Do not attempt to install the projector yourself.

•

To avoid premature lamp failure, do not tilt the front of the projector

up or down by more than 75° from level.Tilting the front of the projec-

tor up or down from 15° to 75° might reduce lamp life by up to 25%.

•

Only use your projector on a solid, level surface. If the projector falls

to the ground, you can be injured and the projector severely dam-

aged.

Do not use the projector where temperatures vary greatly. The pro-

jector must be used at temperatures between 32˚F (0˚C) and 95˚F

(35˚C).

•

Do not expose the projector to moisture, dust, or smoke. This will

harm the screen image.

Ensure that you have adequate ventilation around your projector so

heat can dissipate. Do not cover the vents on the side or the front of

the projector.

E-13

Download from Www.Somanuals.com. All Manuals Search And Download.

Making Connections

NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most

cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.

* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software.

* If you accidentally hit the POWER button on the remote control, wait 90 seconds and then press the POWER button again to resume.

When Viewing a DVI Digital Signal:

To project a DVI digital signal, be sure to connect the PC and the projector using a DVI-D signal cable (not supplied) before turning on your PC or

projector. Turn on the projector first and select DVI (DIGITAL) from the source menu before turning on your PC.

Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should this happen, restart your PC.

Do not disconnect the DVI-D signal cable while the projector is running. If the signal cable has been disconnected and then re-connected, an image

may not be correctly displayed. Should this happen, restart your PC.

NOTE:

•

Use the DVI-D cable compliant with DDWG (Digital Display Working Group) DVI (Digital Visual Interface) revision 1.0 standard. The DVI-D cable should be within

5 m (196") long.

•

The DVI (DIGITAL) connector accepts VGA (640x480), SVGA (800x600), 1152x864, XGA (1024x768) and SXGA (1280x1024 @ up to 60Hz).

Connecting Your PC or Macintosh Computer

DVI IN

RGB 2 IN

RGB 1 IN

DVI-D cable (not supplied)

Audio cable (not supplied)

RGB signal cable (supplied)

To mini D-Sub 15-pin connec-

tor on the projector. It is recom-

mended that you use a com-

mercially available distribution

amplifier if connecting a signal

cable longer than the supplied

one.

IBM PC or Compatibles (Desktop type)

or Macintosh (Desktop type)

PHONE

NOTE: For older Macintosh,

PHONE

use a commercially available

pin adapter (not supplied) to

connect to your Mac's video

port.

IBMVGA or Compatibles (Notebook type)

or Macintosh (Notebook type)

Connecting your PC or Macintosh computer to your projector will en-

able you to project your computer's screen image for an impressive pre-

sentation.

Connecting to RGB 2 IN connectors

Use a BNC

5 cable to connect your PC and the RGB 2 IN connectors

on your projector.

To connect to a PC or Macintosh, simply:

Connecting Your PC with a DVI Connector

1. Turn off the power to your projector and computer.

Use a DVI-D signal cable (not supplied) to connect a DVI connector of

your PC to the projector.

2. Use the supplied signal cable to connect your PC or Macintosh to the

projector.

3. Turn on the projector and the computer.

NOTE: The 8805/8946 is not compatible with video decoded outputs of

4. If the projector goes blank after a period of inactivity, it may be caused

by a screen saver installed on the computer you've connected to the

projector.

Dukane 8805/8946

E-14

Download from Www.Somanuals.com. All Manuals Search And Download.

To connect SCART output (RGB)

Before connections: An exclusive SCART adapter (ADP-SC1) and a

commercially available SCART cable are required for this connection.

1. Turn off the power to the projector and your video equipment.

2. Use the ADP-SC1 SCART adapter and a commercially avail-

able SCART cable to connect the RGB 1 input of your projector and

a SCART output (RGB) of your video equipment.

NOTE:

• Audio signal is not available for this connection.

• The RGB IN 2 connector does not support Plug & Play.

3. Turn on the power to the projector and your video equipment.

4. Use the RGB 1 button on the remote control to select the RGB 1

input.

5. Press the MENU button on the remote control to display the menu.

Projector

Video equipment

such as DVD player

6. From the Advanced menu, select [Projector Options] → [Setup] →

[Page 3] → [Signal Select RGB1] → [Scart].

RGB 1 IN

SCART is a standard European audio-visual connector forTVs,VCRs

and DVD players. It is also referred to as Euro-connector.

NOTE: The ADP-SC1 SCART adapter is obtainable from Dukane

Contact your Dukane.

To RGB IN 1

Commercially available Female

SCART cable

ADP-SC1

Connecting an External Monitor

RGB OUT

LINE IN

PHONE

You can connect a separate, external monitor to your projector to simul-

taneously view on a monitor the RGB analog image you're projecting.

To do so:

NOTE:

•

The RGB OUT connector outputs RGB signal during idle mode (See page E-

47). When the projector goes into idle mode, the image on an external moni-

tor disappears for a moment. Note that the RGB OUT connector will not out-

put RGB signal during Standby mode.

1. Turn off the power to your projector, monitor and computer.

2. Use a 15-pin cable to connect your monitor to the RGB OUT (Mini D-

Sub 15 pin) connector on your projector.

•

When the projector is in the Idle mode, the image may not be correctly dis-

played while the cooling fans are running immediately after turning on or off

the power. Note that the RGB OUT connector will not output RGB signal dur-

ing Standby mode.

3. Turn on the projector, monitor and the computer.

•

Daisy chain connection is not possible.

E-15

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Your DVD Player

RGB 2 IN

RGB 1 IN

Optional 15-pin-to-RCA

(female)

3 cable (ADP-CV1)

RCA(female)-to-BNC(male)

adapter (not supplied)

Component video RCA

3 cable

(not supplied)

Audio Equipment

AUDIO IN

DVD player

AUDIO OUT

Component

Cb Cr

Audio cable

(not supplied)

You can connect your projector to a DVD player with component output

or Video output. To do so, simply:

For a DVD player without component video (Y,Cb,Cr) output, use com-

mon RCA cables (not provided) to connect a composite VIDEO out-

put of the DVD player to the Video Input of the projector.

1. Turn off the power to your projector and DVD player.

3. Turn on the projector and DVD player.

2. If your DVD player has the component video (Y,Cb,Cr) output, use a

commercially available component video cable (RCAX3) and the op-

tional 15-pin-to-RCA (female)

3 cable to connect your DVD player

to the RGB IN1 or IN2 connector on the projector.

NOTE: Refer to your DVD player's owner's manual for more information about

your DVD player's video output requirements,

E-16

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Your VCR or Laser Disc Player

VIDEO IN

S-VIDEO IN

Video cable (not supplied)

S-video cable (not supplied)

Audio equipment

AUDIO IN

VCR/ Laser disc player

AUDIO OUT

VIDEO OUT

S-VIDEO OUT

Audio cable (not supplied)

Use common RCA cables (not provided) to connect your VCR, laser

disc player or document camera to your projector.

To make these connections, simply:

NOTE: Refer to your VCR or laser disc player owner's manual for more informa-

tion about your equipment's video output requirements.

NOTE: An image may not be displayed correctly when a Video or S-Video source

is played back in fast-forward or fast-rewind via a scan converter.

1. Turn off the power to the projector and VCR, laser disc player or

document camera.

2. Connect one end of your RCA cable to the video output connector on

the back of your VCR or laser disc player, connect the other end to

the Video input on your projector. Use an audio cable (not supplied)

to connect the audio from yourVCR or laser disc player to your audio

equipment (if your VCR or laser disc player has this capability). Be

careful to keep your right and left channel connections correct for

stereo sound.

3. Turn on the projector and the VCR or laser disc player.

Connecting the Supplied Power Cable

Connect the supplied power cable to the projector.

First connect the supplied power cable's three-pin plug to

the AC IN of the projector, and then connect the other

plug of the supplied power cable in the wall outlet.

OTE

)

E/H

(

/MO

DIO

B/C

DIO

AC IN

B2 IN

B1 IN

DIO

L/MONO

DIO

L/MONO

DIO

VID

DIO

VID

S-

E-17

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE (BASIC OPERATION)

This section describes how to turn on the projector and to project a

picture onto the screen.

2. Press the ENTER button to execute the selection.

Turning on the Projector

NOTE:

• When plugging in or unplugging the supplied power cable, make sure that the

main power switch is pushed to the off[O] position. Failure to do so may cause

damage to the projector.

SELECT

• The projector has two power switches: main power switch and POWER button

(POWER ON and OFF on the remote control)

• The projector has a feature to prevent itself from being used by unauthorized

individuals. To use this feature, register your PC card as a protect key. See

"Security" in "Projector Options" on page E-53 for more details.

To turn on the main power to the projector, press the Main Power switch

to the ON position ( I ).

3. The Basic menu will be displayed in the language you have selected.

Before you turn on your projector, ensure that the computer or video

source is turned on and that your lens cap is removed.

Only after you press the ON/STAND BY button on the projector cabinet

or POWER ON button on the remote control for a minimum of 2 sec-

onds will the power indicator turn to green and the projector become

ready to use.

To close the menu, press the CANCEL button.

SELECT

Note on Startup screen (Menu Language Select screen)

When you first turn on the projector, you will get the Startup screen.This

screen gives you the opportunity to select one of the seven menu lan-

guages: English, German, French, Italian, Spanish, Swedish and Japa-

nese.

After this has been done, you can proceed to the advanced menu op-

eration.

To select a menu language, follow these steps:

If you want, you can select the menu language later. See "Language"

on page E-45.

1. Use the SELECT ꢀ or ꢁ button to select one of the seven languages

for the menu.

NOTE: To turn the projector on by plugging in the power cable, first turn on the

Main Power switch to ON and use the menu and enable the "Auto Start" feature.

(See page E-47.) Immediately after turning on the projector, screen flicker may

occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.

SELECT

When the Lamp mode is set to Eco, the Lamp indicator will light green.

If one of the following things happens, the projector will not turn on.

If the internal temperature of the projector is too high, the projector

detects abnormal high temperature. In this condition the projector

will not turn on to protect the internal system. If this happens, wait for

the projector's internal components to cool down.

When the lamp reaches its end of usable life, the projector will not

turn on. If this happens, replace the lamp.

If the lamp fails to light, and if the STATUS indicator flashes on and

off in a cycle of six times, wait a full minute and then turn on the

power.

E-18

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting a Source

Adjusting the Picture Size and Position

Place your projector on a flat level surface and ensure that the projector

is square to the screen.

Selecting the computer or video source

Using the Remote Control

Lift the front edge of the projector to center the image vertically.

OFF

POWER

RGB

VIDEO

AUTO ADJ.

VIEWER

LASER

Press any one of the RGB, VIDEO or

VIEWER buttons.

ASPECT FREEZE 3D REFORM

HELP

POINTER PIC-MUTE

VOLUME MAGNIFY

SLIDE

ZOOM

FOCUS

FOLDER

SLIDE

Move the projector left to center the image horizontally on the screen.

LIST

NOTE: If no input signal is available, the projector will display a blue background

(factory preset).

Selecting from Source List

Source List

If the projected image does not appear square to the screen then

use the 3D Reform feature for proper adjustment. See page E-20.

Adjust the Tilt Foot

1. Lift the front edge of the projector.

Press and quickly release the SOURCE button on the projector cabinet

to display the Source list.Each time the SOURCE button is pressed, the

input source will change as follows: "RGB1", "RGB2" (computer or DVD

with component output), "Video" (VCR, document camera, or laser disc

player), S-Video", "DVI (Digital)", "Viewer" (slides on a PC card), or "LAN"

(wired or wireless signal aired from a PC).

To display the selected source, press the ENTER button.

Detecting the Signal Automatically

Adjustable Tilt Foot Lever

Adjustable Tilt Foot

Adjustable Tilt Foot Lever

2. Push up the Adjustable Tilt Foot Levers on the right and left sides of

the projector to extend the adjustable tilt feet (maximum height).

3. Push down the Adjustable Tilt Foot Levers.

Press and hold the SOURCE button for a minimum of 1 second, the

projector will search for the next available input source. Each time you

press and hold the SOURCE button, the input source will change as

follows:

→ RGB1 → RGB2 → Video → S-Video → DVI (Digital)→ Viewer 

If no input signal is present, the input will be skipped. When the input

source you wish to project is displayed, release the button.

Press the ENTER button.

4. Lower the front of the projector to the desired height (max. 44.5mm/

1.8”) and release the AdjustableTilt Foot Lever to lock the Adjustable

tilt foot. There is approximately 10 degrees of up and down adjust-

ment for the front of the projector.

WARNING: To avoid premature lamp failure, do not tilt the front of the

projector up or down by more than 15° from level.

E-19

Download from Www.Somanuals.com. All Manuals Search And Download.

CAUTION:

Correcting the Horizontal and Vertical Key-

stone Distortion (3D Reform)

Do not use the tilt-foot for purposes other than originally intended.

Misuses such as gripping the tilt-foot or hanging on the wall can

cause damage to the projector.

Use the 3D Reform feature to correct keystone (trapezoidal) distortion

to make the top or bottom and the left or right side of the screen longer

or shorter so that the projected image is rectangular.

In the following description, 3D Reform (Cornerstone) correction can be

done with the USB mouse or remote control, cabinet buttons.

Zoom

Use the ZOOM Button (+/-) to fine adjust the image size on the screen

When using the remote control or cabinet buttons:

1. Project an image so that the screen is smaller than the area of the

raster.

2. Pick up any one of the corners and align the corner of the screen

with the one of the image.

Projected image

You can use ZOOM +/- button to enlarge or reduce an image size within

a range of +/-15%.

Screen

Focus

Use the FOCUS Button (+/-) to obtain the best focus.

(The drawing shows the upper right corner.)

3. Press the 3D REFORM button on the remote control.

Using Auto Focus

Press and hold the AUTO ADJUST button on the cabinet or AUTO ADJ

button on the remote control for a minimum of 2 seconds. The focus

pattern will be displayed for a moment and then the best focus will be

automatically obtained.

The CORNERSTONE adjustment screen is displayed.

NOTE: The Auto Functions have two options: Focus and Wall Color Correction.

When the AUTO ADJUST or AUTO ADJ button is pressed and held for a mini-

mum of 2 seconds, either item can be executed. You can decide in advance

which item will be enabled at the time of execution.

NOTE: Press the 3D REFORM button to toggle between "Cornerstone" and "Key-

stone."

From the Advanced menu, select [Projector Options] → [Auto Functions]. You

can turn on or off "Focus" and "Wall Color Correction". See page E-49.

4. Use the SELECT ꢀꢁꢂꢃ button to select one icon which points in

the direction you wish to move the projected image frame.

NOTE: Just pressing quickly the AUTO ADJUST button on the cabinet or AUTO

ADJ button on the remote control will enable the Auto Adjust feature instead of

the Auto Focus feature.

NOTE:

Geometric Correction Tool

If you use a special shaped screen such as a cylindrical or spherical screen, a

downloadable program, Geometric Correction Tool is available.

This program (Geometric Correction Tool) enables the geometrical distortion

correction of an image when projected onto a special shaped screen with an

Dukane projector. Additionally, this program allows control of the projector via a

computer.

Screen

For additional information visit:

US : http://www.dukcorp.com/av

5. Press the ENTER button.

6. Use the SELECT ꢀꢁꢂꢃ button to move the projected image frame

as shown on the example.

E-20

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Press the ENTER button.

3. Press the 3D REFORM button on the remote control.

The Cornerstone adjustment screen is displayed.

The Cornerstone adjustment screen will disappear when you move

the USB mouse cursor.

4. Point to one of the remaining 3 corners and left-click on it.

Left-click on the corner.

Screen

8. Use the SELECT ꢀꢁꢂꢃ button to select another icon which points

in the direction.

5. Do the above step 4 for the other two corners so that the projected

area becomes smaller than the screen.

Screen

On the Cornerstone adjustment screen, select

“Exit”and then“OK”, or press the CANCEL but-

ton on the remote control.

Screen

The confirmation screen is displayed.

Left-click on each corner.

6. To complete the procedure, right-click anywhere on the screen.

The confirmation screen is displayed.

9. Press the SELECT ꢂ or ꢃ button to highlight the [OK] and press the

ENTER button.

7. Left-click on "OK".

This completes the Cornerstone adjustment.

To return the Cornerstone adjustment to the default settings, left-

click on "Reset" in Step 7.

This completes the keystone correction.

Selecting “Cancel” will return to the adjustment screen without saving

changes (Step 3).

Selecting "Reset" will return to the factory default.

Selecting "Undo" will exit without saving changes.

You can save your Cornerstone changes.The changes are saved when

you turn off the projector.To do so, select [Projector Options] → [Setup]

→ [Page 4]. Select the 3D Reform Save check box.This is not selected

at the time of shipment.

When using the USB connected to the projector

Preparation: Connect the USB mouse to the projector. See page E-28.

* There are limitations of shapes which can be corrected using the Cor-

nerstone adjustment.

When adjusting the Cornerstone beyond these limits, you will get the

message "Out of adjustment range!" and no correction can be done.

Should this happen, do the Cornerstone adjustment again within the

allowable range.

* Due to limitations of accuracy within internal processes, there may be

some discrepancy of positions between the mouse cursor and corrected

shape or one corner and the other 3 corners.

1. Project an image so that the screen is smaller than the area of the

raster.

2. Pick up any one of the corners and align the corner of the screen

with the one of the image. (The drawing shows the upper right cor-

ner.)

Projected image

NOTE: To return the 3D Reform correction setting values to the factory default,

press and hold the 3D REFORM button for a minimum of 2 seconds.

Screen

E-21

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE: During 3D Reform adjustment, "Aspect Ratio" and "Screen" may not be

available. Should this happen, first reset the 3D Reform data and then do each

setting. Second repeat the 3D Reform adjustment. Changing Aspect Ratio and/

or Screen setting can limit 3D Reform in its adjustable range.

Turning Up or Down Volume

Sound level from the speaker and the AUDIO OUT jack (RCA) on the

projector can be adjusted.

The adjustable ranges for 3D Reform are as follows:

Horizontal ........... Max 35° approx.

VOLUME

Vertical ............... Max +50°/-25° approx.

increase volume

The following are conditions at the above maximum angle when all of

the following are met

•

Image is projected in Wide (Zoom)

Resolution is XGA

decrease volume

Higher resolution than XGA limits 3D Reform in its adjustable range.

Menu items should be set as follows:

Aspect Ratio ............................... 4:3

Screen Type ................................ 4:3

Horizontal and Vertical are adjusted separately.

•

Volume bar

•

A combination of both adjustments limits 3D Reform in its adjustable

range.

When "4:3 Fill" is selected in Aspect Ratio, "Cornerstone" and "Hori-

zontal Keystone" are not available.

Optimizing RGB Picture Automatically

Adjusting the Image Using Auto Adjust

Using the Laser Pointer

Optimizing RGB image automatically

Press the Auto Adjust button to optimize an RGB image automatically.

You can use the laser to draw your audience's attention to a red dot that

you can place on any object.

Press and hold the LASER button to activate the laser pointer.

[Poor picture]

AUTO ADJ.

[Normal picture]

AUT

LASER

FREEZE

INTER

PIC-MUTE

MAGNIFY

FOCUS

FOLDER

SLIDE

CAUTION:

Press the Auto Adjust button to fine-tune the computer image or to re-

move any vertical banding that might appear and to reduce video noise,

dot interference or cross talk (this is evident when part of your image

appears to be shimmering). This function adjusts the clock frequencies

that eliminate the horizontal banding in the image. This function also

adjusts the clock phase to reduce video noise, dot interference or cross

talk. (This is evident when part of your image appears to be shimmer-

ing.)

• Do not look into the laser pointer while it is on.

• Do not point the laser beam at a person.

This adjustment may be necessary when you connect your computer

for the first time.

NOTE:

• Some signals may not be displayed correctly or take time.

• The Auto Adjust function does not work for component and video signal.

• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock

and Phase manually. See page E-41.

• Pressing and holding the AUTO ADJUST button on the cabinet or AUTO ADJ

button on the remote control for a minimum of 2 seconds will enable the Auto

Focus and the Auto Wall Color Correction feature instead of the Auto Adjust

feature.

E-22

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the function switch

There are two switches on the bottom of the battery case: an applicable

projector selector switch (1) and laser enable/disable switch (2). Check

the projector being used and decide whether to enable or disable laser,

then set these switches as necessary using the tip of a thin ball-point

pen. On this model, an applicable projector selector switch (1) is not

used.

OFF

Switch (2)

On:

Off:

Enabled (the laser lights when the LASER button is pressed)

[Factory default]

Disabled (the laser does not light even when the LASER but-

ton is pressed)

Disable the laser when using in an environment in which the unit is

accessible to children.

Turning off the Projector

OFF

POWER

RGB

VIDEO

AUTO ADJ.

VIEWER

LASER

To turn off the projector:

First press the POWER (ON/STAND BY) but-

ton on the projector cabinet or the POWER OFF

button on the remote control for a minimum of

two seconds. The power indicator will glow or-

ange. After the projector turns off, the cooling

fans keep operating for 90 seconds (Cooling-

off time).

ASPECT FREEZE 3D REFORM

Second, turn off the Main Power switch. The

power indicator will go out. Last unplug the

power cable.

HELP

POINTER PIC-MUTE

VOLUME MAGNIFY

SLIDE

ZOOM

FOCUS

FOLDER

SLIDE

LIST

CAUTION

Do not unplug the power cable from the

wall outlet or do not turn off the main power

under any one of the following circum-

stances. Doing so can cause damage to

the projector:

•

While the Hour Glass icon appears.

•

While the message "Please wait a mo-

ment." appears. This message will be

displayed after the projector is turned

off.

•

While the cooling fans are running. (The

cooling fans continue to work for 90 sec-

onds after the projector is turned off).

While accessing a PC card. (The PC Card

Access indicator lights.)

E-23

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES

When using the USB Port

Using the Remote Mouse Function

For PC, the mouse receiver function can only be used with a Windows

98, Windows ME, Windows XP or Windows 2000 operating system.

The built-in remote mouse function enables you to operate your

computer's mouse functions from the remote control (Computer mode).

It is a great convenience for clicking through your computer-generated

presentations.To return to the projector operation mode (Projector mode),

press the PJ button (lit red).

USB port (PC)

Connecting to your computer for the remote mouse

function

If you wish to use the remote mouse function, use the supplied USB

cable to connect the USB port (PC) of the projector and the USB port

(type A) of your computer.

NOTE: Depending on the type of connection or OS installed on your computer,

you may have to restart your computer or change you computer settings.

USB port

(Type A)

NOTE: Wait at least 5 seconds after disconnecting the USB cable before recon-

necting it and vice versa. The computer may not identify the built-in mouse re-

ceiver if it is repeatedly connected and disconnected in rapid intervals.

Switching operation mode between computer and projector

The three shaded buttons shown on the drawing work as a computer mouse in the Computer mode.

In the Computer mode the PJ button is not lit.

Works as a mouse for your computer.

Works as the SELECT button on the projector.

OFF

POWER

RGB

POWER

RGB

VIDEO

AUTO ADJ.

VIEWER

LASER

VIDEO

AUTO ADJ.

VIEWER

LASER

Works as a right-click button

for your computer.

Works as the CANCEL

button on the projector.

Lit red

Not lit

ASPECT FREEZE 3D REFORM

HELP

POINTER PIC-MUTE

HELP

POINTER PIC-MUTE

Works as the ENTER

button on the projector.

VOLUME MAGNIFY

SLIDE

VOLUME MAGNIFY

SLIDE

Works as a left-click

button for your com-

puter.

ZOOM

FOCUS

FOLDER

SLIDE

ZOOM

FOCUS

FOLDER

SLIDE

LIST

•

When the MENU button is pressed, the PJ button lights red to indicate that you are in the Projector mode, which allows the projector menu

operation using the three buttons.

When the POINTER button is pressed, the PJ button lights red to indicate that you are in the Projector mode and that the SELECT ꢀꢁꢂꢃ

button works as a moving button for the POINTER or magnified image.

If no buttons are pressed within 60 seconds, the PJ button's light goes out to indicate that you are in the Computer mode.To enable the projector

menu operation again, press the PJ button to light red.To move the pointer or a magnified image again, turn off the pointer and then turn on the

pointer (press the POINTER button two times).

•

When the PJ button is lit, if you want to use the mouse function immediately, press the PJ button to return to the Computer mode (not lit).

During Computer mode:

In Computer mode, by pressing the ENTER button for 2 seconds or more then releasing, the drag mode is set and the drag operation can be

performed simply by pressing the SELECT ꢀꢁꢂꢃ (mouse) button. To drop the item, press the ENTER (left click) button again or press the

CANCEL (right click) button.

E-24

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Place the projector adjusting its orientation and the angle so that the

outline (outer frame) of the screen can be positioned within the gray

area of the projected guide pattern.

Auto 3D Reform

Auto 3D Reform automatically corrects distortion by sensing the outline

or outer frame of your screen with the projector’s built-in image sensor

to project an image within the screen.

NOTE:

•

The Auto 3D Reform feature supports screen sizes between 30” and 200”.

If the screen has the same brightness as its background, the built-in image

sensor on the front of the projector can fail to recognize the outline or outer

frame of the screen.

Should this happen, the Auto 3D Reform feature cannot function.

If irregular colors, flaw or change of color are seen on the screen, the built-in

sensor can mistakenly interpret the outline or outer frame of the screen.

If there is an object between the built-in sensor and the screen, the screen

cannot be recognized.

The Auto 3D Reform feature does not support reflective screens. Matt type or

beads type screens are recommended.

•

Executing the Auto 3D Reform feature

Screen’s outer frame

1. Project an image.

See the user’s manual or the quick connect guide for projecting an

image.

5. Highlight [Start] and press the ENTER button.

The Auto 3D Reform feature has been executed. Processing takes

about 20 seconds

To cancel, use the SELECT ꢂ or ꢃ button to highlight [Cancel] and

press the ENTER button.

2. Press the 3D REFORM button.

The 3D Reform (Cornerstone) screen is displayed.

NOTE:

When “4:3 Fill" is selected in “Aspect”, the Auto 3D Reform feature is not

available.

If the screen’s outer frame is larger than gray area of the guide pattern as

shown, the Auto 3D Reform feature does not function.

Projected area

In the Auto 3D Reform mode, when controlling the projector using PC con-

trol, you might not be able to make correction. (The projector can be oper-

ated with Dynamic Image Utility 2.0, Image Express Utility 1.0 and HTTP

Server function.)

3. Press and hold the AUTO ADJUST button for a minimum of 2 sec-

onds.

A guide pattern that shows available area for Auto 3D Reform is dis-

played.

The AUTO ADJ. button on the remote control can also be used for

this purpose.

Not recommended

E-25

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Screen of Auto 3D Reform

1. Press the MENU button.

The Basic menu is displayed.

When the Advanced menu is displayed, go to Step 3.

2. Use the SELECT ꢀ or ꢁ button to highlight “To Advanced Menu” and

press the ENTER button.

The Advanced menu is displayed.

3. Use the SELECT ꢀ or ꢁ button to highlight “Projector Options”.

Press the SELECT ꢃ button.The “3D Reform” option is highlighted.

4. Use the SELECT ꢀ or ꢁ button to highlight “Auto Functions”.

Press the SELECT ꢃ button. The “Auto Functions” screen is dis-

played.

Focus ............. See page E-49.

Wall Color

Correction ...... See page E-49.

3D Reform ..... Clear a check mark from the check box to disable

the Auto 3D Reform.

Adjustment

Inside ............. Corrects so that an image is projected inside of

the screen outline.

Outside .......... Corrects so that an image is projected outside of

the screen outline.

Sensitivity ...... If the built-in sensor sensitivity is so strong that it

recognizes even lines within the screen, select

“Lower”.If the built-in sensor sensitivity is too weak

to recognize the screen, select “Higher”.

NOTE: If you failed to correct for placing the image inside of the screen using

[Inside], the projector automatically corrects to project the image larger than the

outer frame of the screen.

E-26

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning Off the Image and Sound

Enlarging and Moving a Picture

Press the Picture Mute button to turn off the image and sound for a

short period of time. Press again to restore the image and sound.

You can enlarge the area you want up to 400 percent.

To do so:

PIC-MUTE

1. Press the Pointer button to display the pointer.

POINTER

Freezing a Picture

Press the Freeze button to freeze a picture. Press again to resume

motion.

FREEZE

2. Move the pointer to the area you want to enlarge.

Using the Pointer

SELECT

You can use one of nine pointers to draw your audience's attention to

the portion of a projected image you want.

POINTER

3. Enlarge the selected area.

When the Magnify (+) button is pressed, the image is magnified. To

move the magnified image, use the SELECT button.

MAGNIFY

Press the Pointer button to dis-

play the pointer.

Press the Pointer button to display the pointer.

4. Return the image to the original size.

MAGNIFY

SELECT

Use the Select button to move

the pointer.

Use the Select button to move the pointer.

Getting the On-line Help

You get the contents about Help.

HELP

SELECT

Display Help

Exit Help

E-27

Download from Www.Somanuals.com. All Manuals Search And Download.

Using a USB Mouse

Using the USB HUB Function

Using a USB mouse gives you a smooth operation.A commercially avail-

able USB mouse is required.

When using the projector with a PC via the supplied USB cable, both

the USB port(type A) on the projector can be connected to a USB-sup-

ported scanner or other USB-supported device. (USB Hub Function)

(

)

Example: When connecting a PC and a scanner to each USB port re-

spectively

USB MOUSE/HUB

(

)

(

)

USB MOUSE/HUB

USB PC

NOTE:

•

The MT1065 comes with a USB mouse.

There may be some brands of USB mouse that the projector does not sup-

port.

An example of how a scanned image is projected

1. Install the Dynamic Image Utility on your PC.

NOTE: The Dynamic Image Utility is contained on the supplied CD-ROM. See

the supplied NEC Software Utility Installation Guide for the installation proce-

dure.

Operate the Menus using the USB mouse

Mouse Cursor

When connecting a USB mouse to the projector, you get a mouse

cursor on the screen.

Unless you use your USB mouse within 10 seconds, the mouse cur-

sor disappears.

2. Use your scanner to scan an image.

NOTE: A scanner driver must be installed on your PC before use.

Menu Display

3. Load the scanned image on your PC using the Dynamic Image Util-

ity.

Clicking with a mouse button displays the menu.

Clicking ꢃ displays the pull-down menu. To close the menu, click

anywhere in the background.

4. Transmit the scanned image from your PC to the projector via the

USB cable and project the image on the screen.

Adjusting and Setting Display

You can select a menu item and click with a mouse button to make

adjustments and setting.

NOTE:

•

The USB HUB function is effective only when “Auto” is selected in Operation

Mode Select.

Examples

•

The PCs using the USB Host Controller may not be available.

When connecting a USB hub to the USB port (type B) on the projector, be

sure to use a USB hub capable of supplying 500mA per port of downstream

current.

Click (or press and hold) the mouse button ꢂ or ꢃ to adjust the bright-

ness.Or click and drag the mouse button on the slide bar horizontally

to adjust it.

To save the adjustments, click

. The display is closed. If you click

anywhere in the background while displaying adjustment and setting

menu or dialog box, you will get the main menu at the clicking point.

Using the middle button on the mouse

The projector supports the middle button on your mouse. With the middle

button you can use a scroll bar when it is available or click the middle

button to display or hide the Chalkboard toolbar.

E-28

Download from Www.Somanuals.com. All Manuals Search And Download.

Drag ............ Drags to move the tool bar by clicking on the blue part.

(for USB mouse operation only)

Changing Background Logo

Pen .............. Left-click and drag to draw. Left-click [ꢀ] or right-click the

pen icon to display the pen palette containing four lines of

different thickness from which you can select a line you

prefer by left-clicking.

Color ........... Selects a color. Left-click to display the color palette from

which you can select a color you prefer by left-clicking.

Capture ....... Left click to capture and save freehand drawings in the

PC card.

Eraser ......... Left-click and drag to erase part of a drawing. Left-click

[ꢀ] or right-click the eraser icon to display the eraser pal-

ette containing four eraser of different thickness from which

you can select an eraser you prefer by left-clicking.

Clear ........... Left-click to clear the drawing completely from the

ChalkBoard screen.

You can change the default background logo using the PC Card Files

feature.

NOTE: File size must be 256KB or less. Other file formats than JPEG and BMP

are not available.

1. From the menu, select [Tools] → [PC Card Files] to display a list of all

the files stored in the PC card so that you can select a file you want to

use as a background logo.

Drive ............ Switches between PC Card slot 1 and 2.

Hide ............. Hides the tool bar by left-clicking. Right-clicking anywhere

on the screen displays the ChalkBoard tool bar again.

Exit .............. Clears the complete drawing and exits the ChalkBoard.

NOTE:

• The menu is not available while you display the ChalkBoard screen.

• Switching slides clears a drawing completely.

2. The Logo button allows you to select a background logo from graphic

files on a PC card and change to it as the background logo.

USB Memory Device or USB Memory Card

Reader Support

3. Use the SELECT ꢀ or ꢁ button to select a JPEG or BMP file for your

background logo.

The projector is compatible with either a USB memory device or USB

memory card reader which supports the viewer and security features.

4. Use the SELECT ꢃ and then ꢁ button to select "Logo".

5. Press the ENTER on the remote control or the cabinet. You will get

the confirmation dialog box.

6. Select "OK" and press the ENTER button. This completes changing

a logo for the background.

•

To use a USB memory device or USB memory card reader, connect

the device to the USB port (type A).

Select one of the Drive icons in the Viewer toolbar, Capture toolbar

and PC Card File setting screen. Up to four drives can be accepted.

To use a USB memory device as a Protect key for Security function,

select one from the Drive icons in the Security setting screen.

Once you have changed the background from the logo to an-

other, you cannot return the logo to background even by using Fac-

tory Default. To do so, repeat the above steps. The logo file is

included on the supplied CD-ROM Projector User Supportware

(Logo/nec_bb_x.jpg).

NOTE:

•

Some USB memory devices (brands) or USB memory card readers may not

work.

•

You cannot use a USB memory device and a USB memory card reader when

connecting a USB mouse to the projector.

Using a USB HUB that allows multiple USB memory devices or card readers

is not supported either.

Do not do the following while the USB memory device or USB memory card

reader’s access indicator is lit or flashing (while data is being accessed.) Do-

ing so can damage your USB memory device or USB memory card in the

reader. Back up your data in case it will need to be restored.

Making Freehand Drawings on a Projected

Image (ChalkBoard)

•

The ChalkBoard feature allows you to write and draw messages on a

projected image.

Pulling out the USB memory device or USB memory card reader from the

USB port of the projector.

NOTE: The ChalkBoard feature is available only when a USB mouse is used.

Pulling out the memory card from the USB memory card reader

Turning off the main power switch or unplugging the power cable.

From the menu, select [Tools] → [ChalkBoard] to display the ChalkBoard

tool bar that contains the following icons.

•

The drive for ”USB 1-4” is displayed only when the USB memory device or

USB memory card reader is connected to the projector. The drive for “USB 1-

4” may be displayed differently from the one in the USB memory card reader.

Some USB memory devices (brands) or USB memory cards cannot be used

as Protect key for the projector’s Security function.

Eraser

Drive

Pen

Exit

Drag

Color

Clear

Hide

Capture

E-29

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

Inserting and Removing a PC Card

NOTE:

•

To use the Viewer, first you need to create presentation materials on your PC

using the Dynamic Image Utility 2.0 contained on the supplied Projector

User Supportware CD-ROM. For installation, see the printed Software

Utility Installation Guide. For creating presentation materials, see the Slide

show function on the on-line manual of the Dynamic Image Utility 2.0.

NOTE:

•

Do not try to force the PC card into the slot.

A dummy card is inserted into each slot at the time of shipment. First remove

the dummy cards before use.

•

Selecting Viewer sets the audio input for DVI input.

Making the Most out of the Viewer Function

Features

You can view presentation data, capture, and play images on the pro-

jector. A PC card is used to view presentation data prepared on the

computer and to capture and play images projected with the projector.

The Viewer feature allows you to view slides stored on a PC memory

card (referred to as PC card in this manual) on the projector. Even if no

computer is available, presentations can be conducted simply with the

projector. This feature is convenient for holding presentations at meet-

ings and in offices, as well as for playing images taken on digital cam-

eras.

Inserting the PC Card

•

Hold the PC card horizontally and insert it slowly into PC card

slot 1 or 2 with its top facing up.

•

The eject button pops out once the PC card is fully inserted.

Check that the PC card is fully inserted.

PC card (not supplied)

Easy to use

•

Presentations can be started immediately simply by inserting a

PC card (not supplied)

•

Easy slide switching

REMOTE

)

Remote control operation

(

Jumping to list of slides or any specific slide

High quality images

VIDEO IN

•

High resolution up to 1024 x 768 dots

24-bit full color playback

Removing the PC Card

Press the eject button.The PC card pops out a little.Grasp the edges

of the PC card and pull it out.

Viewing of digital camera images

Simple utility software (for computer)

•

Dynamic Image Utility 2.0 operable on Windows 98/Me/XP/2000

NOTE: Do not eject the PC card while its data is being accessed.

Slides can be created by capturing the currently displayed im-

age

Eject button

•

Control screen for displaying lists of slides and editing

Microsoft, Windows and PowerPoint are registered trademarks

of Microsoft Corporation.

PC CONTROL

)

MOUSE/HUB

(

USB

L/MONO

AUDIO

B/Cb

DVI IN

AUDIO OUT

G/Y

AUDIO

RGB OUT

RGB2 IN

RGB1 IN

AUDIO

L/MONO

AUDIO

L/MONO

AUDIO

-V

Direction for Inserting the PC Card

The PC card has a top and bottom and must be inserted into the PC

card slot in a specific direction. It cannot be inserted backwards or up-

side-down. Attempting to force it into the slot in the wrong direction may

break the internal pin and damage the card slot. Refer to the PC card's

operating instructions for the proper direction of insertion.

PC Card Type

The PC Card slot accepts PCMCIA Type II only.

NOTE: The projector does not support FAT32 or NTFS formatted flash memory

card or USB memory device.

Be sure to use a flash memory card or USB memory device formatted with the

FAT16 or FAT file system.

To format your flash memory card or USB memory device in your computer,

refer to the document or help file that comes with your Windows.

E-30

Download from Www.Somanuals.com. All Manuals Search And Download.

When the tool bar is not displayed:

Operating the Viewer Function from the

Projector (playback)

Press the FOLDER LIST button or the SLIDE LIST button on the re-

mote control to display folders or from a PC card in the projector's PC

Card slot.

This section describes the operation for showing slides of presentation

documents created using the Viewer function with the projector. It is

also possible to make slides directly from the images projected with the

projector.

FOLDER

Projecting slides (Viewer)

1. Insert a PC card into the PC card slot.

Insert the PC card so that the end with the insertion direction arrow

on the top goes in first.

Multi cursor (blue marks)

Press the eject button to eject the card.

Folder

2. Select the "Viewer" from the Source Select menu.

3. Project slides.

Checking "Show Folder List", means that selecting Viewer input dis-

plays a list of the folders in the PC card and if "Auto Play" is checked the

projector automatically starts to play slides at the first slide of the folder

you have selected.

02 : 0001 / 0008

Current folder number

A tool bar will appear when you press the MENU button on the remote

control or the projector cabinet or clicking with the right button of a mouse.

Number of all slides in

folder

Current slide

number

Delete

Play

Jump

Drive

Use the SLIDE +/- button to advance to the next folder or return to the

previous folder.

Drag

View

Setup

Stop

Select

SLIDE

The tool bar includes the following buttons:

Folder

Drag ............ Drags to move the tool bar.This is available for USB mouse

operation only.

Prev ............. Returns to the previous slide or folder. Or this lets you

play slides back in reverse.

Next ............. Advances to the next slide or folder. Or this lets you play

slides back.

Play ............. Plays back automatically or manually depending on the

setting on Viewer Options of the menu.This allows you to

move on to the next slide when "Manual Play" is selected.

Use the SLIDE +/- button to advance to the next slide or return to the

previous slide.

Stop............. This allows you to stop Auto Play while you are playing

back and to resume playing from the selected slide or folder

when "Auto Play" is selected.

Slide(Table) cursor

(green marks)

Slide

Jump ........... Displays a list of slides while you are playing back.

Select .......... Displays a list of folders while you are playing back.

Drive ............ Switches between PC Card slot 1 and 2.

Setup........... Displays the Viewer Options dialog box on Page 2 of the

Setup dialog box.

Delete.......... Deletes a captured slide(s) or all the captured slides in

the Capture - specific folder.

02 : 0004 / 0008

View ............ Hides the tool bar while you are playing back. Pressing

the MENU button or clicking with the right button of a

mouse shows it again.

NOTE: If no memory card is inserted in the PC CARD slot, there is no signal, and

a black, blue or logo background is displayed, depending on the setting.

Playback is stopped when SLIDE +/- button on the remote control or ꢂꢃ button

on the cabinet is pressed in Auto Play mode.

Up to 12 indexes can be displayed on the list of folders. The folder in the right

bottom is always a folder exclusively for captured images, but is only displayed

when images have been captured.

E-31

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparations:

NOTE: You can also use the ꢂ and ꢃ button on the remote control to select

folders or slides.

If you use the ꢂ and ꢃ button on the remote control for Viewer operation, press

the PJ button to switch to the Projector mode and the PJ button lights red.

Insert the PC card into the card slot.

Insert the PC card so that the end with the insertion direction arrow

on the top goes in first.

* Press the eject button to eject the card.

1. Project the image you wish to store on the projector.

2. Select the "Capture" from the Tools menu.

Works as the Select button on the

projector.

SELECT

Lit red

3. A tool bar will appear.

Auto Play Mode

If the "Auto Play" option is selected in "Viewer Options" of the menu,

any given slide will start to play automatically.

You can also specify Auto Play Interval between 5 and 300 seconds.

Capture

Drag

Freeze

Exit

Switching to Slides Directly from Other Input Modes

Drive

The tool bar includes the following buttons:

With this function it is possible to switch directly to a slide when the

picture of a VCR or computer is being projected.

Example:When conducting presentations using a combination of slides

and moving pictures from a VCR, etc., it is possible to switch from a

Viewer slide to the video picture then back to the Viewer slide simply by

using the Viewer button.

Drag ............ Drags to move the tool bar by clicking on the blue part (for

USB mouse operation only).

Capture ....... Captures an image and save it as a JPEG file on a PC

card.

NOTE: Even if you switch the current Viewer source to another source, the cur-

rent slide is retained. When you return back to the Viewer, you will get the slide

that has been retained.

Freeze ......... Freezes and unfreezes images.

Drive ............ Switches between PC Card slot 1 and 2.

Exit .............. Exits the Capture function. Another option to exit the Cap-

ture function is to press MENU or CANCEL button on the

remote control or projector cabinet.

The PC card editing operation cannot be performed from the projector.

Do so using the Dynamic Image Utility 2.0 software.

Viewing Digital Images

NOTE:

You can compress a captured file (JPEG) using the Capture Options in the Setup

dialog. See page E-46.

Digital images can be played with the Viewer if the following conditions

are met:

Captured images with higher resolution than the projector's native resolution

cannot be displayed correctly.

•

If the image can be stored on an MS-DOS format PC card

If the image can be stored in a format supported by the Viewer. With

the Viewer, images on the card are searched for in directories and

images in JPEG or BMP format are recognized as slides.Searchable

directories are directories within two steps from the root directory,

and searchable images are images within the first 12 files in the di-

rectory. Only file and slide switching are possible.

• File size of the captured image varies depending on the resolution of an input

signal.

• An hourglass indicating that an image is being captured appears on the

projector's display. Do not eject the PC card or turn off the projector's power

while this icon is displayed. Doing so will damage the PC card data. If the PC

card data is damaged, use a computer to repair the data.

• Up to 12 indexes can be displayed on the list of folders. The folder in the right

bottom is always a folder exclusively for captured images, but is only dis-

played when images have been captured.

NOTE: The maximum number of images recognized as slides within one direc-

tory is 128.

Storing Images Displayed on the Projector on the PC

card (Capture)

The Capture features allows you to capture an image from a source that

is currently being displayed. The image is saved as JPEG in the PC

card. When you select Capture from the menu, you will get a tool bar.

You can capture an image directly using the tool bar when the menu is

not displayed.

NOTE:

* Unless a PC card is inserted into the PC Card slot of the projector, the Capture

feature is not available.

* The "Card Error" display means that the free space of the PC card is insufficient

for saving images. Make more space available on the card by erasing un-

wanted images with your PC. The number of images that can be captured

depends on the size of the PC card.

* Be sure not to turn off the power or remove the PC card while capturing an

image. Doing so could cause a loss of the data in the PC card or damage to the

card itself.

E-32

Download from Www.Somanuals.com. All Manuals Search And Download.

Deleting Captured Images

Using the Delete button on the tool bar for Viewer can delete captured

images.

Delete

Play

Jump

Drive

Drag

View

Setup

Stop

Select

To delete captured images:

1. Select Viewer and display a folder list of captured images.

2. Use button to select the Capture folder [Cap] in the right bottom of

the screen.

3. Press the MENU button to display the tool bar.

4. Use the ꢂ or ꢃ button to select the Delete icon and press the EN-

TER button or click with a mouse button.

Using the PC Card Files Fucntion (PC Card Files)

The PC Card Files function allows you to display a list of all the files

stored in the PC card so that you can select a file you want to display.

You can also sort files by file name or date, or display the file. Although

a list of all the files in the PC card is displayed, you can view files in idx,

text, HTML, JPEG and BMP format only. Selecting BMP and JPEG files

automatically switches to the Viewer source. See also page E-39.

NOTE: This option is not available for selection unless a PC card is inserted

properly.

Selecting "Execute" displays the file you selected.

When you select a JPEG or BMP file and press the ENTER button on

the remote or the cabinet, or "Execute" on the above, you will get a

toolbar. This toolbar is used to return to the PC Card Files screen.

Drag

Return

Drag ............ Drags to move the tool bar. (for USB mouse operation

only)

Return ......... Returns to the PC Card Files screen.

Close ........... Close the toolbar.

E-33

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU

The default Custom Menu items are:

Basic Menu Operation

Source Select (RGB 1/2, Video, S-Video, DVI(DIGITAL), Viewer and

LAN), Picture, Sound, Image Options (Aspect Ratio), Picture Manage-

ment, Projector Options (3D Reform, Menu, Setup, Lamp Setting, Screen

and LAN Mode), Tools (Sleep Timer, Capture, PC Card Files and

ChalkBoard) and Help (Contents and Information).

Using the Menus

NOTE: The on-screen menu may not be displayed correctly while interlaced mo-

tion video image is projected.

1. Press the MENU button on the remote control or projector cabinet to

display the Basic, Advanced or Custom Menu.

NOTE: Once you have selected OK on the Custom Menu Edit screen, you cannot

cancel the changes on the Menu screen. However, you can reedit the menu items

over again as described in the steps above.

NOTE: When using a USB mouse, click the mouse button to display the menu.

For other operations, do the same way as you use your PC mouse.

2. Press the SELECT ꢀꢁ buttons on the remote control or the projec-

tor cabinet to highlight the menu for the item you want to adjust or

set.

NOTE: If the "Advanced Menu" item has been selected on the Menu mode, you

get the "Confirmation Change Menu" upon completion of "Custom Menu" editing.

In this case, selecting "Yes" then "ENTER" will close all the menus and apply the

changes from the Advanced menu to the Custom Menu. If you select "No" then

"ENTER" functions, then all menu items will return to the Advanced menu, but

your changes will still be available within the "Custom Menu" selection. To dis-

play the previously tailored Custom Menu, select "Custom Menu" from the "Menu

Mode".

3. Press the SELECT ꢃ button or the ENTER button on the remote

control or the projector cabinet to select a submenu or item.

4. Adjust the level or turn the selected item on or off by using SELECT

ꢂ or ꢃ buttons on the remote control or the projector cabinet.

The on-screen slide bar will show you the amount of increase or

decrease.

An item "To Advanced Menu" will be added to the bottom of the Custom

Menu.

5. Changes are stored until you adjust it again.

Selecting this item and pressing the ENTER button will display the "Ad-

vanced Menu" features.

ENTER .......... Stores the setting or adjustments.

CANCEL ........ Return to the previous screen without storing settings

or adjustments.

NOTE: You can close the main and sub menus simultaneously by pressing

the PJ button on the remote control to cancel the Projector mode.

6. Repeat steps 2-5 to adjust an additional item, or press the CANCEL

button on the projector cabinet or the remote control to quit the menu

display.

Customizing the Menu

The Custom menu can be customized to meet your requirements. Se-

lecting a menu item from the "Custom Menu Edit" list, allows you to

custom tailor the menu items to your needs.

1. Select "Custom Menu Edit" to display the "Custom Menu Edit" screen.

2. Use the SELECT ꢀ or ꢁ buttons to highlight your selection and press

the ENTER button to place a check mark next to an option.

This action enables that feature. Press the ENTER button again to

clear the check box.

If you select an item with a solid triangle ꢃ and press the ENTER

button on the remote control or the projector cabinet, you can enable

all the items within that submenu. Also you can turn on an item within

the submenu without placing a check mark on the main menu item.

NOTE: Up to 12 main menu items (within Custom Menu Edit, not including

submenu items) can be selected.

3. In order for the changes to take effect, use the SELECT ꢂ or ꢃ but-

ton on the remote control or the projector cabinet to highlight "OK",

then press the ENTER button. To cancel the changes, use the SE-

LECT ꢀ or ꢁ buttons to highlight "Cancel" and press the ENTER

button.

To return to the factory default, select "Reset" then press the ENTER

button.

E-34

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu tree

Advanced Menu

Source Select

Picture

RGB1

RGB2

Video

Sound

S-Video

DVI (DIGITAL)

Viewer

LAN

Image Options

Picture Management

Projector Options

Tools

User1

User2

User3

Entry List

Help

Factory Default

Picture

Brightness, Contrast, Color,

Hue, Sharpness

Volume, Bass, Treble

Aspect Ratio

4:3, Letterbox, Wide Screen, Crop / 4:3

Window, Letterbox, Wide Screen, 4:3 Fill

Top, Bottom, Left, Right

Horizontal, Vertical, Clock, Phase

Auto, Native

Blanking

Position/Clock

Resolution

Overscan

0%, 5%, 10%, 25%

Video Filter

Noise Reduction

Signal Type

Off, Less, More

Off, Low, Medium, High

RGB, Component

Picture Management

Presentation, sRGB, Graphic, Video,

Movie, User 1, User 2, User 3, User 4

E-35

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Menu

Source Select

Picture

Cornerstone

Keystone

Horizontal, Vertical

Sound

Off, User 1, User 2, User 3, User 4 (Auto Adjust Button)

Image Options

Picture Management

Projector Options

Tools

3D Reform

Wall Color Correction

Setup

Page 1

Help

Lamp Setting

Screen

Language

English, Deutsch,

Français, Italiano,

Español, Svenska

Factory Default

Auto Functions

LAN Mode

Password

Security

Menu Mode

Basic Menu,

Custom Menu,

Advanced Menu

Custom Menu Edit

Pointer 1-9

Setup

Projector Pointer

Mouse Pointer

Page 1

Pointer 1-9

Orientation

Desktop Front, Ceiling Rear,

Desktop Rear, Ceiling Front

Blue, Black, Logo

Menu Display Time Manual, Auto 5sec,

Auto 15sec,

Background

Auto 45sec

RGBOUT Terminal Last, RGB1, RGB2

Page 2

Closed Caption

Off, Caption1-4, Text1-4

Source Display

Message

On, Off

Page 2

Viewer Options

Show Folder List

Menu Color Select Color, Monochrome

Auto Play, Manual Play, Interval

High Quality, Normal,

High Compression

Capture Options

Mouse Button

Right Hand, Left Hand

Sensitivity Fast, Medium, Slow

Operation Mode Select Auto, Projector

Page 3 Signal Select

RGB1 RGB/Component, RGB, Component, Scart

RGB2 RGB/Component, RGB, Component, Scart

Video, Auto, PAL-M/PAL-N/NTSC3.58, NTSC3.58,

S-Video NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM

Page 4

Auto Adjust, Auto Start, Power Management,

Power Off Confirmation, 3D Reform Save,

High Speed Fan Mode, Built-in Speaker, Idle Mode,

Clear Filter Usage Meter

Page 5

Remote Sensor

Front, Back, Left, Right

S-Video Mode Select Off, S2

Page 6

Communication Speed

Default Source Select

4800, 9600, 19200, 38400

Last, Auto, Select (RGB1, RGB2,Video,

S-Video, DVI(DIGITAL), Viewer, LAN)

Enable, Disable

Control Panel

Key Lock

E-36

Download from Www.Somanuals.com. All Manuals Search And Download.

Lamp Mode

Lamp Type

Normal, Eco

Standard Lamp,

Extended Life Lamp

Advanced Menu

Source Select

Picture

Screen Type 4:3, 16:9 / Position

3D Reform

Wall Color Correction

Focus

On, Off

Volume

Wall Color Correction

3D Reform

Adjustment

Sensitivity

On, Off

Image Options

Picture Management

Projector Options

Tools

On, Off

Setup

Inside, Outside

Lower, Medium, Higher

Lamp Setting

Screen

Help

Auto Functions

LAN Mode

Password

Security

Factory Default

LAN Mode

IP Address

Automatic

Manual

IP Address,

Subnet Mask,Gateway

Projector Name

DNS Configuration

Domain Name

Network Type

Mode

Infrastructure,

802.11 Ad Hoc, Ad Hoc

Easy Connection

Sleep Timer

Capture

PC Card Files

ChalkBoard

SSID

Channel

TX rate

1-14

Automatic, 11M, 5.5M, 2M,

1M, 1M-2M-Automatic

Contents

WEP

Information

WEP

Disable, 64bit, 128bit

Key1-4

Key Select

Key1-4

Factory Default

All Data,

Mail

Alert Mail

Current Signal

Sender's Address

SMTP Server Name

Recipient's Address 1

Recipient's Address 2

Recipient's Address 3

Test Mail

Status

IP Address

Subnet Mask

MAC Address

Logo

Security

Enable, Disable, Keyword,

Use Protect key, Drive, Read,

E-37

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Elements

Highlight

Help Button

Close Button

Title bar

Tab

Radio button

OK Button

Cancel Button

Solid triangle

Check box

Slide bar

Drag

Tool bar

Menu windows or dialog boxes typically have the following elements:

Cancel button ..... Press to cancel your setting. You will return to the

previous menu.

Title bar .............. Indicates the menu title.

Close button ....... Click to close the window with saving changes. (USB

mouse only)

Highlight ............. Indicates the selected menu or item.

Solid triangle ...... Indicates further choices are available. A highlighted

triangle indicates the item is active.

Help button ......... Indicates that help about that feature is available (USB

mouse only). Press the Help button on the remote

control to display help.

Tab ..................... Indicates a group of features in a dialog box. Select-

ing on any tab brings its page to the front.

Toolbar ............... Contains several icons for specific tasks. It is also

referred to as “launcher”.

Radio button ....... Use this round button to select an option in a dialog

box.

Drag ................... Point the mouse here, and click and drag to move a

toolbar.

Check box .......... Place a checkmark in the square box to turn the op-

tion On.

Slide bar ............. Indicates settings or the direction of adjustment.

OK button ........... Press to confirm your setting. You will return to the

previous menu.

E-38

Download from Www.Somanuals.com. All Manuals Search And Download.

Delete

Entering Alphanumeric Characters by Using the Menu

Play

Jump

Drive

Alphabet or numeric characters are used for your IP address or projec-

tor name.To enter IP Address or projector name, use the software key-

board.

Drag

For using the software keyboard, see page E-64.

View

Setup

Stop

Select

Drag ............... Drags to move the tool bar. (for USB mouse opera-

tion only)

Prev ............... Returns to the previous slide or folder.

Next ............... Advances to the next slide or folder.

Play ................ Plays back automatically or manually depending on

the setting on Viewer Options of the menu. This al-

lows you to move on to the next slide when "Manual

Play" is selected.

Stop ............... Stops Auto Play while you are playing back and to

resume playing from the selected slide or folder when

"Auto Play" is selected.

Jump .............. Displays a list of slides while you are playing back.

Select ............. Displays a list of folders while you are playing back.

Drive .............. Switches between PC Card slot 1 and 2.

Setup ............. Displays the Viewer Options dialog box on Page 2 of

the Setup dialog box.

Delete ............ Deletes a captured slide(s) or all the captured slides

in the selected folder.

View ............... Hides the tool bar while you are playing back. Click-

ing with the right button of a mouse shows it again.

Provides access to controls for your image. Use the

SELECT button on the projector cabinet or the re-

mote control to highlight the menu for the item you

want to adjust.

Menu Descriptions & Functions

Source Select

Selecting a Source

Enables you to select a video source such as a VCR, DVD player, laser

disc player, computer or document camera depending on what is con-

nected to your inputs. Press the SELECT ꢀꢁ button on the projector

cabinet or on your remote control to highlight the menu for the source

you want to project.

LAN

Selects a signal from a LAN card plugged into the projector's card

slot.

Entry List

RGB

Selects the computer connected to your RGB1, RGB2 or component

signal.

NOTE: An optional component cable (Component V or ADP-CV1 cable) is

needed for a component signal.

Video

Selects what is connected to yourVideo input-VCR, laser disc player,

DVD player or document camera.

S-Video

Selects what is connected to your S-Video input-VCR, DVD player,

or laser disc player.

Displays the list of the entry signals. Use the SELECT ꢀꢁ buttons on

your remote control or the projector cabinet to select the signal and

press the ENTER button on the remote control or the projector cabi-

net to display the Entry Edit Command screen.

NOTE: A frame may freeze for a brief period of time when a video is played

back in fast-forward or fast-rewind with a Video or S-Video source.

DVI (DIGITAL)

Selects the computer connected to the DVI input connector.

Using the Entry List

Making any ajustments to the current picture will automatically regis-

ter its adjustments to the Entry List. The registered signal can be

loaded any time from the Entry List.

Viewer

This feature enables you to make presentations using a PC card that

contains captured images and slides created with the exclusive Dy-

namic Image Utility 2.0 contained in the CD-ROM. See the supplied

Software Utility Installation Guide for installing the Dynamic Image

Utility 2.0.The starting screen for theViewer varies depending on the

settings of the Setup's Page 2. See Setup on page E-46.

NOTE: Up to 100 presets can be registered.

NOTE: Even if you switch the current Viewer source to another source, the

current slide is retained. When you return back to the Viewer, you will get the

slide that has been retained. A launcher will appear when you press the MENU

button.

A press of the MENU button displays the toolbar;a press of the MENU

button again displays the Menu and hereafter each press of the MENU

button switches displaying between the Menu and the toolbar.

The launcher is a tool bar including the following buttons:

E-39

Download from Www.Somanuals.com. All Manuals Search And Download.

Entry Edit Command

Picture (not available for Viewer and LAN)

Adjusting Brightness, Contrast, Color, Hue, and Sharpness

Brightness ...... Adjusts the brightness level or the back raster inten-

sity.

Contrast ......... Adjusts the intensity of the image according to the

incoming signal.

Color .............. Increases or decreases the color saturation level (not

valid for RGB).

You can edit signals on the Entry List.

Load ............... Enables you to select a signal from the list.

Hue ................ Varies the color level from +/- green to +/-blue. The

red level is used as reference.This adjustment is only

valid for Video and Component inputs (not valid for

RGB).

Store .............. Enables you to store the currently projected signal.

Cut ................. Enables you to remove a selected signal from the list

and place it on the "clipboard" in the projector.

Copy .............. Enables you to copy a selected signal from the list

and place it on the "clipboard" in the projector.

Sharpness ..... Controls the detail of the image for Video (Not valid

for RGB).

Paste .............. Enables you to paste the signal placed on the "clip-

board" to any other line of the list. To do this, select

"Paste" and then select the line number you want to

paste to. Last press ENTER.

Sound

Controlling Volume, Bass and Treble.

Adjusts the sound, bass and treble level of the projector speaker and

AUDIO OUT (RCA).

Edit ................ Enables you to change source names or add source

names to "More" in the Sorce Select.

Source Name .. Enter a signal name.Up to 18 alpha-

numeric characters can be used.

Image Options

Selecting Aspect Ratio (not available for Viewer and LAN)

Aspect Ratio allows you to select the best Aspect mode to display your

source image.

When screen size 4:3 is selected for the source, the following selections

will display:

Input Terminal .. Change the input terminal. RGB1

and RGB2 are available for RGB sig-

nal;Video and S-Video are available

for composite signal.

Source List ...... Set signal selection method.

Lock ................ Set so that the selected signal can-

not be deleted when "All Delete" is

executed.

4:3 .................. Standard 4:3 aspect

Letter Box ...... Reduced to display the true aspect with black bor-

ders on top and bottom

Skip ................. Set so that the selected signal will

be skipped during auto search.

Wide Screen .. Left & Right stretched with black borders on top and

bottom

When complete, select OK and press ENTER.To exit

without storing setting, select Cancel.Select "Source

Name" and press ENTER to display the Source Name

Edit window. You can change source name on this

window. Press [ꢁ] to display the software keyboard,

which you can enter alphanumeric characters. See

page E-64 for the key function of the software key-

board.

Crop ............... Left & Right stretched.

Left & Right sides cut. Available for 4:3 only.

When screen size 16:9 is selected for the source, the following selec-

tions will display:

4:3 Window .... Reduced to display the true aspect with black bor-

ders on right and left

All Delete ....... This feature enables you to delete all the registered

signals in the Entry List.

Letter Box ...... Standard 16:9 aspect

Wide Screen .. Left and right stretched to display the true aspect

4:3 Fill ............ Stretched to display in 16:9 aspect ratio

The following buttons are not available for the currently projecting

signals:

1) The Cut and Paste buttons on the Entry Edit Command screen

2) The Input Terminal button on the Entry Edit screen

NOTE: You can adjust image positions vertically for source with black borders.

See page E-49 for setting image positions.

Please note that using this projector for the purpose of commercial gain or the

attraction of public attention in a venue such as a coffee shop or hotel and em-

ploying compression or expansion of the screen image with a "Aspect Ratio" or

"Screen" setting may raise concern about the infringement of copyrights which

are protected by copyright law.

NOTE: During 3D Reform adjustment, "Aspect Ratio" may not be available.

Should this happen, first reset the 3D Reform data and then do setting again.

Second repeat the 3D Reform adjustment.

Changing the aspect ratio can limit 3D Reform in its adjustable range.

Input

Signal

Screen

Type

Letterbox

Squeeze

4:3

Crop

Wide Screen

4:3 Screen

Letterbox

16:9 Screen

Wide Screen

4:3 Fill

4:3 Window

E-40

Download from Www.Somanuals.com. All Manuals Search And Download.

Masking Unwanted Area (Blanking)

This feature allows you to mask any unwanted area of the screen

image.

Selecting Noise Reduction Level (not available for RGB, Viewer and LAN)

Select one of the three levels for reducing video noise: Low, Medium

or High.

Adjust the Top, Bottom, Left or Right blanking with the SELECT ꢂ or

ꢃ button.

NOTE: The lower the Noise Reduction level, the better the image quality by

way of higher video bandwidth.

Adjusting Position and Clock

This allows you to manually adjust the image horizontally and verti-

Signal Type

cally, and adjust Clock and Phase.

Select either the RGB signal type or the Component signal type.

Horizontal/Vertical Position:

RGB ............... RGB signal

Adjusts the image location horizontally and vertically using the SE-

LECT ꢂ and ꢃ buttons.This adjustment is made automatically when

the Auto Adjust is turned on. See "Auto Adjust" on page E-47 for

turning on or off the Auto Adjust feature.

Component .... Component signals such as Y/Cb/Cr, Y/Pb/Pr

NOTE: This feature is available on RGB 1 and 2 only. If you do not get a better

picture even when you set "Signal Select" to "Component" in Setup, set this to

"Component".

Clock .............. Use this item to fine tune the computer image or to

remove any vertical banding that might appear. This

function adjusts the clock frequencies that eliminate

the horizontal banding in the image.

Picture Management

Press the SELECT ꢂ and ꢃ buttons until the band-

ing disappears. This adjustment may be necessary

when you connect your computer for the first time.

This adjustment is made automatically when the Auto

Adjust is turned on.

Phase ............ Use this item to adjust the clock phase or to reduce

video noise, dot interference or cross talk. (This is

evident when part of your image appears to be shim-

mering.) Use the SELECT ꢂ and ꢃ buttons to adjust

the image.

Use "Phase" only after the "Clock" is complete. This

adjustment is made automatically when the Auto Ad-

just is turned on.

This option allows you to adjust neutral tint for yellow, cyan or magenta.

There are 5 factory presets optimized for various types of images, or

you can set 4 user adjustable settings.

Selecting Resolution

This allows you to activate or deactivate the Advanced AccuBlend

feature.

Presentation .. Recommended for making a presentation using a

PowerPoint file

Auto ............... Turns on the Advanced AccuBlend feature. The pro-

jector automatically reduces or enlarges the current

image to fit the full screen.

sRGB ............. Standard color values

Native............. Turns off the Advanced AccuBlend feature. The pro-

jector displays the current image in its true resolu-

tion.

Graphic .......... Recommended for graphics

Video ............. Recommended for regular picture such as TV pro-

gram

See "Auto Adjust" on page E-47 for turning on or off

the Auto Adjust feature.

Movie ............. Recommended for movie

User 1-4 ......... User adjustable

NOTE:

* When "Resolution" is set to "Native", "3D Reform", "Aspect Ratio", "Screen"

and "Overscan" are not available.

* While you are displaying an image with higher resolution than the projector's

native resolution, “Resolution” is not available.

NOTE: When "sRGB", "Graphic", "Video" or "Movie" is selected, the brightness

decreases slightly when compared to "Presentation". This is not a malfunction.

User Adjust (when using User 1 to 4)

Selecting Overscan Percentage

Select overscan percentage (0%, 5%, 10% and 25%) for signal.

NOTE: When "Resolution" is set to "Native", this feature is not available, and

the stored settings and adjustments are invalid.

NOTE: When "4:3 Fill" or "Crop" is selected in "Aspect Ratio", this feature is not

available.

Selecting Video Filter Level (not available for Video, Viewer and LAN)

This function reduces video noise.

Off .................. The filter is removed.

Less ............... The low-pass filter is applied partially.

More .............. The low-pass filter is applied fully.

When selecting one of four user adjustable presettings (User 1 through

4), the submenu will be displayed.

You can customize each gamma or color. To do so, first select [Set-

ting] and press the ENTER button, and then proceed the following

steps.

E-41

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting Gamma Correction Mode

Use the ꢂ or ꢃ buttons to choose one mode from three options.

Each mode is recommended for :

Projector Options

Using 3D Reform

This feature corrects trapezoidal distortion so that the projected im-

age is rectangular.

Dynamic ......... For true color reproduction of natural tones

Natural ........... Normal settings

Two options are available for correcting procedures.

You can save adjustment settings by using the 3D Reform Save op-

tion on Setup (See page E-47).

Black Detail .... For dark portions of a picture

Cornerstone

Selecting Color Correction

See page E-20.

Adjusts red, green, blue, yellow, magenta, cyan and color gain each

independently to correct the tint on whole screen.

Adjusting Color Temperature and White Balance

This feature adjusts the color temperature using the slide bar.

Checking "Color Temperature" enables the color temperature slide

bar and disables the “White Balance” button.

Clear “Color Temperature” and press the White Balance button to

access the Contrast/Brightness adjustment for each R, G, and B.

NOTE: "Color Temperature" and "White Balance" are a trade-off.

The White Balance is not available for Viewer and LAN.

Keystone

Selecting Base Setting

This feature allows you to use color correction or gamma values as

reference data to optimize for various types of images.You can select

one of the following five settings.

• Presentation

• Video

• sRGB

• Movie

• Graphic

1. Press the SELECT ꢂꢃ button to adjust the horizontal keystone.

2. Press the SELECT ꢀꢁ button to select "Vertical".

3. Press the SELECT ꢂꢃ button to adjust the vertical keystone.

4. After completing, press the ENTER button.This will return to the menu

screen.

When "Resolution" is set to "Native", "Cornerstone" and "Keystone"

are not available.

Keystone Correction at Zoomed Lens Position

You can zoom in or out, while keeping an image that was corrected

using Keystone, without again having to make those adjustments.

Improvements in 3D Reform performance allows the projector's adjust-

ment range (horizontal and vertical combinations) to be wider by ap-

proximately 25% in the maximum telephoto position when compared to

initial units shipped.

NOTE: There are some cases when adjusting the zoom position from Tele to

Wide (after performing Keystone correction in Tele) can result in a message

“Range Over ! 3D Reform data has been cleared.”. In this case correction values

for Keystone will return to the factory default setting.

E-42

Download from Www.Somanuals.com. All Manuals Search And Download.

Using Adapting Color Correction [Wall Color Correction]

2. Highlight "Automatic".

3. Use the SELECT ꢁ button to highlight "Execute" and then press the

ENTER button.

The Auto Wall Color Correction will be executed.

This function allows for correcting the color of the projected images on

textured walls using the image sensor on the projector. There are two

ways for color correction: Automatic and Manual. Automatic correction

affects all colors; Manual correction allows you to correct each color R,

G, B, and W respectively.

NOTE: When Auto Wall Color Correction is enabled in the Auto Functions menu,

Wall Color Correction can be executed by pressing and holding the AUTO AD-

JUST or AUTO ADJ button for a minimum of 2 seconds.

Manual Wall Color Correction

Off .................. Disables this function

Preparation: Before correcting manually, prepare a non-glossy, non-

transparent, clean white paper (300 mm

420 mm). Hereafter re-

ferred to as "the white paper for Wall Color Correction."

User 1 to 4 ..... Executes correction. Four settings can be saved.

User 4 (AutoAdjustButton) stores settings when the

Auto Function is executed by pressing and holding

the AUTO ADJUST button or AUTO ADJ. button for a

minimum of 2 seconds.

1. Choose a selection from User 1 – 4. Highlight "Setting" and press the

ENTER button.

The correction mode select screen is displayed.

To read the pre-adjustment settings. Choose a selection User 1 – 4,

highlight "OK" and press the ENTER button.

Info box .......... Displays "Automatic" or "Manual". This is the option

you have set for User 1 – 4 setting.

NOTE: Correction may not be possible depending on ambient room lighting,

walls with a texture that is glossy or with certain patterns, or walls that are the

2. Highlight "Manual".

color black or primary deep colors.

If you try to correct beyond the limit, an error message "Out of correction range!"

will be displayed. This message means that you will not be able to correct the

color due to the above reasons.

Also, When the image sensor fails to pick up the image of a wall color during

Auto Wall Color Correction, an error message "Failed to execute Auto Wall Color

Correction" will be displayed. This message means that there may be an obstacle

between the wall and the image sensor on the projector, or the image sensor

may not work because of too much ambient light. Make corrections to what

seems to be the problem and try again.

3. Use the SELECT ꢁ button to highlight "Execute" and then press the

ENTER button.

The Manual Wall Color Correction (Red) screen will be displayed.

Automatic Wall Color Correction

1. Choose a selection from User 1 – 4. Highlight "Setting" and press the

ENTER button.

The correction mode select screen will be displayed.

To read the pre-adjustment settings. Choose a selection from User 1

– 4, highlight "OK" and press the ENTER button.

Working area

E-43

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Place the white paper forWall Color Correction over the working area

in the Manual Wall Color Correction (Red) screen.

Paste the white paper for Wall Color Correction loosely or get some-

one to hold it.

6. Use the SELECT ꢀꢁꢂꢃ button to move the yellow box to select a

color density.

Moving the yellow box changes the color density of the selected por-

tion in the palette.

Move the yellow box so that a color on the white paper for Wall Color

Correction becomes close to a color of the projected image on the

wall.

Position of the white paper for

Wall Color Correction

NOTE: The size of the above Manual Wall Color Correction screen changes de-

pending on the screen size.

Actual color of the projected

image on the wall

5. Use the SELECT ꢂ or ꢃ button to move the blue frame to the work-

ing area and then press the ENTER button.

A yellow box will appear in the palette.

Color of the projected image on the white

paper for Wall Color Correction

To move the Manual Wall Color Correction (Red) screen, high-

light "Move" and then press the ENTER button.

7. When you complete the correction, press the ENTER button.

The "Next" will be highlighted.

The "Slide Bar" button adjusts Hue, Saturation and Brightness.

8. Press the ENTER button.

The Manual Wall Color Correction (Green) screen will be displayed.

Palette

Yellow box

9. Repeat steps 4 to 8. Adjust Red, Green, Blue and White respectively.

When you complete correcting White, the Exit Adjustment screen is

displayed.

10. Highlight the Correction Level bar and then use the SELECT ꢂ or ꢃ

button to finely adjust.

Blue frame

11. Highlight "OK" and press the ENTER button.

E-44

Download from Www.Somanuals.com. All Manuals Search And Download.

Allows you to set preferences for the on-screen menu. Press "OK" to

save your changes for all the features of Page 1 and Page 2.

Selecting Menu Display Time:

This option allows you to select how long the projector waits after the

last touch of a button to turn off the menu.

The preset choices are "Manual", "Auto 5 sec", "Auto 15 sec", and

"Auto 45 sec". The "Auto 45 sec" is the factory preset.

[Page1]

Manual ........... The menu can be turned off manually.

Auto 5 sec ...... The menu will automatically be turned off in 5 sec-

onds if no buttons are pressed within 5 seconds.

Auto 15 sec .... The menu will automatically be turned off in 15 sec-

onds if no buttons are pressed within 15 seconds.

Auto 45 sec .... The menu will automatically be turned off in 45 sec-

onds if no buttons are pressed within 45 seconds.

[Page 2]

Selecting Menu Language [Language]:

You can choose one of seven languages for on-screen instructions.

The options are:English, German, French, Italian, Spanish, Swedish

and Japanese.

Selecting Menu Mode [Menu Mode]:

This feature allows you to select 3 menu modes: Advanced Menu,

Custom Menu and Basic Menu.

Advanced Menu ............ This is the menu that contains all the avail-

able menus and commands.

Turning On / Off Source Display [Source Display]:

This option turns on or off input name display such as RGB1/2,Video,

and No Input to be displayed in the top right corner of the screen.

Basic Menu ................... This is the basic menu that contains mini-

mum essentials of menus and commands.

Turning On / Off Message [Message]:

This option turns on and off messages for lamp life warning, 3-minute

before power off time, “Please clean filter”and “Please wait a moment”.

Custom Menu ............... This is the menu that you can customize us-

ing the Custom Menu Edit to fit your needs.

Customizing the Menu:

See page E-34 for instructions about how to customize the Menu.

Selecting Menu Color [Menu Color Select]:

You can choose between two color modes for menu color: color and

monochrome.

Selecting Projecting Pointer Icon [Projector Pointer]:

This enables you to select from nine different Pointer icons for the

"Pointer" button on your remote control.

After moving your Pointer icon to the area you want on the screen,

press the Magnify button on the remote control to enlarge the se-

lected area on the screen. See page E-27 for more details.

NOTE: There may be cases where the Pointer function is not available (ex. a

non-interlace signal at 15kHz such as video game.)

Selecting a Mouse Pointer Icon [Mouse Pointer]:

This option enables you to select one of nine different mouse point-

ers when using a USB mouse.

E-45

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup

Enables you to set operating options.

[Page 2]

Press "OK" to save your changes for all the features of Page1, Page2,

Page3, Page 4, Page 5 and Page 6.

[Page 1]

Setting Viewer Options [Viewer Options]

Show Folder List:

If this option is checked, when the Viewer source is selected on the

projector, the folder lists will be displayed and allows you to select the

presentation from a PC card.

Selecting Projector Orientation [Orientation]:

This reorients your image for your type of projection.The options are:

desktop front projection, ceiling rear projection, desktop rear projec-

tion, and ceiling front projection.

Auto Play:

If this option is checked, when the Viewer source is selected on the

projector any given slide will start to play automatically.

Selecting a Color or Logo for Background [Background]:

Auto Play Interval:

You can specify interval time between 5 and 300 seconds.

Use this feature to display a blue/ black screen or logo when no sig-

nal is available.The default background is “Blue”.You can change the

logo screen using the PC Card Files feature. See page E-29.

NOTE: The Auto Play Interval time set on “Slide Show Settings” of the Dy-

namic Image Utility 2.0 overrides the one set here.

Setting RGB 1 or 2 for RGB OUT [RGBOUT Terminal]:

This option allows you to determine which RGB source is output from

the RGBOUT connector during Idle mode.

Manual Play:

Views a slide manually when the Viewer source is selected.

Last ................ The signal from the last RGB input will be output to

the RGBOUT connector.

Selecting Capture Options [Capture Option]: (available for JPEG only)

These options are used for the Capture function that you can select

from Tools. You have three options for JPEG compression quality:

High quality, Normal and High Compression.

RGB 1 ............ The signal from RGB1 IN will be output to the

RGBOUT connector.

RGB 2 ............ The signal from RGB2 IN will be output to the

RGBOUT connector.

High Quality .................. Gives quality of JPEG a priority.

Normal .......................... Gives normal JPEG quality.

High Compression ........ Gives compression a priority.

NOTE: The AUDIO OUT mini jack will not output sound during the Idle mode.

Setting Closed Caption:

This option sets several closed caption modes that allows text to be

superimposed on the projected image.

Setting Mouse Button and Sensitivity [Mouse]:

This option lets you to change your USB mouse settings.The mouse

settings feature is available for USB mouse only. Choose the settings

you want:

CAPTION 1-4 Text is superimposed.

TEXT 1-4 ....... Text is displayed in full screen.

OFF ............... This exits the closed caption mode.

Mouse Button ............... "Right Hand" or "Left Hand"

Mouse Sensitivity .......... "Fast", "Medium" or "Slow"

Selecting Operation Mode [Operation Mode Select]

Set the operation mode of the USB mouse connected to the USB

port (MOUSE/HUB) on the projector

Auto ............... Depending on connection of the USB port (PC) on

the projector and a USB port (type A) on your PC,

the USB mouse is operated in the following way:

When connecting the projector to your PC

The USB mouse connected to the projector can

be used as a PC mouse.

When not connecting the projector to your PC

The USB mouse connected to the projector can

perform menu operation of the projector.

Projector ........ The USB mouse connected to the projector can per-

form menu operation of the projector.

E-46

Download from Www.Somanuals.com. All Manuals Search And Download.

[Page 3]

Enabling Auto Start [Auto Start]:

Tur ns the projector on automatically when the power cable is inserted

into an active power outlet and the main power switch is turned on.

This eliminates the need to always use the "Power" button on the

remote control or projector cabinet.

Enabling Power Management [Power Management]:

When this option is on and there is no input for five minutes or more,

the projector will automatically turn itself off.

Enabling Power Off Confirmation [Power Off Confirmation]:

This option determines whether a confirmation dialog for turning off

the projector will appear or not.

NOTE: When the confirmation message is displayed, you must be in the Pro-

jector mode to operate your projector using the remote control. If not, press

the PJ button on the remote control to change your projector to the Projector

mode. The button lights to indicate that you are in the Projector mode.

Enabling Horizontal and Vertical Keystone Correction Save

[3D Reform Save]:

This option enables you to save your current 3D Reform settings.

Saving your change once affects all sources.The changes are saved

when you turn off the projector.

Selecting Signal Format [Signal Select]

RGB1/2:

Allows you to choose "RGB" for an RGB source such as a computer,

or "Component" for a component video source such as a DVD player.

Normally select "RGB/Component" and the projector automatically

detects an either incoming signal. However there may be some com-

ponent signals that the projector is unable to detect. If this is the

case, select "Component". Select "Scart" in RGB 1 or 2 for the Euro-

pean Scart.

Enabling High Speed Fan Mode [High Speed Fan Mode]:

This option allows you to select two modes for fan speed:high-speed

mode and normal speed mode.

When you wish to cool down the temperature inside the projector

quickly, check this box.

NOTE: Enable High Speed Fan mode if you continue to use the projector for

consecutive days.

VIDEO and S-VIDEO:

This feature enables you to select composite video standards manu-

ally. Normally select "Auto". Select the video standard from the pull-

down menu. This must be done for Video and S-Video separately.

Selecting Built-in Speakers [Built-in Speaker]:

This option allows you to mute the built-in speakers.

[Page 4]

Enabling Idle Mode [Idle Mode]:

The projector has two standby modes: Standby and Idle.

Standby is the mode that allows you to put the projector in the standby

condition which consumes less power than the idle mode. The pro-

jector is preset for Idle mode at the factory.

When this check box is turned on, you allow the RGB OUT connector

to output RGB signal during Idle mode.

NOTE:

* The RGB OUT connector will not output signal during the Standby mode.

* Via the USB interface the projector can be turned on from your PC using

Dynamic Image Utility 2.0 during the Standby or Idle mode. On the LAN

connection the projector can be controlled or monitored from your PC us-

ing Dynamic Image Utility 2.0 only in the Idle mode.

* The HTTP server functions are not available during Standby mode.

Resetting the Filter Usage Hours [Clear Filter Usage Meter]:

Resets the filter usage back to zero. Pressing this button appears a

confirmation dialog box. To reset the filter usage hours, press "OK".

Enabling Auto Adjust [Auto Adjust]:

When "Auto Adjust" is set to "On", the projector automatically deter-

mines the best resolution for the current RGB input signal to project

an image using NEC's Advanced AccuBlend Intelligent Pixel Blend-

ing Technology.

The image can be automatically adjusted for position and stability;

"Horizontal Position", "Vertical Position", "Clock", "Phase", and "Reso-

lution".

On .................. Automatically adjusts image "Horizontal Position",

"Vertical Position", "Clock", "Phase" and "Resolution".

Off .................. User can adjust the image display functions ("Hori-

zontal Position", "Vertical Position", "Clock", "Phase"

and "Resolution") manually.

E-47

Download from Www.Somanuals.com. All Manuals Search And Download.

[Page 5]

[Page 6]

Remote Sensor:

Selecting Communication Speed [Communication Speed]:

This feature sets the baud rate of the PC Control port (D-Sub 9 Pin).

It supports data rates from 4800 to 38400 bps.

This option determines which remote sensors on the projector are

enabled in wireless mode.

The options are: front, rear, right, or left. All checked boxes indicate

that they can accept the infrared signal from the supplied remote

control.

The default is 38400 bps. Select the appropriate baud rate for your

equipment to be connected (depending on the equipment, a lower

baud rate may be recommended for long cable runs).

S-Video Mode Select:

Selecting Default Source [Default Source Select]:

You can set the projector to default to any one of its inputs each time

the projector is turned on.

This feature is used to select the S-Video signal detection mode.

This allows identifying of the S-Video signals with different aspect

ratio (16:9 and 4:3).

Last ................ Sets the projector to default to the previous or last

active input each time the projector is turned on.

Off .................. Does not identify any S-video signal.

S2 .................. Identifies the 16:9 or 4:3 signal.

Auto ............... Searches for an active source in order of RGB1 →

RGB2 →Video → S-Video → DVI(DIGITAL) →Viewer

→ RGB1 and displays the first found source.

Select ............. Displays the selected source input every time the pro-

jector is started up.Select an input from the pull-down

menu.

Disabling the Cabinet Buttons [Control Panel Key Lock]:

This option turns on or off the Control Panel Key Lock function.

NOTE:

* This Control Panel Key Lock does not affect the remote control and the PC

Control functions.

* When the cabinet buttons are disabled, pressing and holding the CANCEL

button for about 10 seconds will change the setting to enabled.

Selecting Lamp Mode and Lamp Type [Lamp Setting]

Lamp Mode:

This feature enables you to select two brightness modes of the lamp:

Normal and Eco modes. The lamp life can be extended by using the

Eco mode.

Normal Mode . This is the default setting (100% Brightness).

Eco Mode ...... Select this mode to increase the lamp life (80% Bright-

ness).

Lamp Type:

The lamp type you use is displayed here.

456-8946 ......... Standard life lamp (8946)

456-8805 ......... Standard life lamp (8805)

MT60LPS ....... Optional extended life lamp. When the optional ex-

tended life lamp is used, the Lamp Mode is available.

E-48

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting Aspect Ratio and Position for Screen [Screen]

NOTE:

1. If neither Focus or Wall Color Correction are enabled in the Auto Functions

menu when you press and hold the AUTO ADJUST or AUTO ADJ button

for a minimum of 2 seconds, the Auto Adjust function (Position/Clock/

Phase) will be performed instead of Auto Focus and Auto Wall Color Cor-

rection.

2. Due to specifications of the image sensor on the projector, Auto Functions

are effective to image sizes between 40" and 150"(diagonal). Also in some

cases Auto Functions may not work correctly depending on projection

conditions such as textured material of the screen or ambient light.

Screen Type:

Select either 4:3 Screen or 16:9 Screen for the screen to be used.