Projector
Dukane 8917H
User's Manual (concise)
Thank you for purchasing this projector.
WARNING ►Before using this product, be sure to read all manuals for this
product. See “Using the CD manual” ( 12) to read the manuals in the CD.
After reading them, store them in a safe place for future reference.
Contents
Contents of package........................... 1 Displaying the picture......................... 7
Preparations....................................... 2 Turning off the power.......................... 8
Fastening the lens cover.................................
2
2
Replacing the lamp............................. 9
Cleaning and replacing the air filter.. 11
Loading batteries into the remote control........
Arrangement....................................... 3 Using the CD manual ....................... 12
Connecting your devices.................... 4 Regulatory notices............................ 13
Connecting power supply................... 5 Specifications ................................... 15
Turning on the power.......................... 5 Warranty and after-service ............... 16
Adjusting the projector’s elevator ....... 6
Contents of package
Your projector should come with the items
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
(1)
(5)
(6)
ASPECT
AUTO SEARCH BLANK
MAGNIFY FREEZE
ON
PAGE
UP
VOLUME
㧗
shown below. Check that all the items are
included. Require of your dealer immediately
if any items are missing.
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
POSITION
ENTER
ESC
RESET
(1) Remote control with two AA batteries
(2) Power cord
(3) RGB cable
(4) Audio/Video cable
(5) Lens cover and Strap
(6) User’s manuals (Book x1, CD x1)
(7) Soft case
(2)
(3)
(4)
(7)
(8)
(8) Security label
NOTE • Keep the original packing materials for future reshipment. Be sure
to use the original packing materials when moving the projector. Use special
caution for the lens.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Arrangement
Refer to the illustrations and tables below to determine screen size and projection distance.
The values shown in the table are calculated for a full size screen: 1280×800
a
Screen size (diagonal)
b
Projection distance (±10%)
c1 c2
,
Screen height (±10%)
On a horizontal surface
Suspended from the ceiling
• Keep a space of 30 cm or more
between the sides of the projector and
other objects such as walls.
• Consult with your dealer before a
special installation such as suspending
from a ceiling.
16 : 10 screen
4 : 3 screen
a
b
b
c1
Screen
height
c2
Screen
height
c1
Screen
height
c2
Screen
height
Screen size
(diagonal)
Projection distance
Projection distance
min.
max.
min.
max.
type
(inch)
m
m
inch
m
inch cm inch cm inch
m
inch
m
inch cm inch cm inch
30 0.8 0.9 36 1.1 44
40 1.0 1.2 49 1.5 59
50 1.3 1.6 61 1.9 74
60 1.5 1.9 74 2.3 89
40
53
66
79
16
21
26
31
36
1
1
1
2
2
2
2
3
3
4
5
7
8
0
0
1
1
1
1
1
1
1
2
2
3
3
1.1 41 1.3 50
1.4 56 1.7 67
1.8 70 2.1 84
45
60
75
18
24
31
37
1
1
2
2
2
2
3
3
4
5
6
8
9
0
0
1
1
1
1
1
1
1
2
2
3
4
2.1 84 2.6 101 90
70 1.8 2.2 86 2.6 104 92
2.5 98 3.0 118 105 43
2.8 112 3.4 135 119 49
3.2 126 3.9 152 134 55
3.6 140 4.3 169 149 61
4.3 169 5.1 203 179 74
5.4 211 6.4 254 224 92
7.2 282 8.6 338 299 123
9.0 352 10.8 423 373 153
10.7 423 12.9 508 448 184
80 2.0 2.5 99 3.0 119 106 42
90 2.3 2.8 111 3.4 134 119 47
100 2.5 3.1 124 3.8 149 132 52
120 3.0 3.8 149 4.5 179 158 62
150 3.8 4.7 186 5.7 224 198 78
200 5.1 6.3 249 7.6 299 264 104
250 6.4 7.9 311 9.5 374 330 130
300 7.6 9.5 374 11.4 449 396 156
WARNING ►Install the projector in a stable horizontal position.
Place the projector in a cool place, and ensure that there is sufficient ventilation.
►
►Do not place the projector anyplace where it may get wet.
CAUTION ►Avoid placing the projector in smoky, humid or dusty place.
►Position the projector to prevent light from directly hitting the projector’s
remote sensor.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector.
Make sure that all the devices are suitable to be connected with this product, and
prepare the cables required to connect. Please refer to the following illustrations
to connect them.
PC
Monitor
RGB IN
RS-232C
RGB OUT
USB
AUDIO OUT
RGB OUT
AUDIO OUT
Speakers
(with an
amplifier)
AUDIO IN
Y
CB/PB CR/PR
L
R
L
R
L
R
VIDEO OUT
S-VIDEO OUT
COMPONENT VIDEO OUT
AUDIO OUT
AUDIO OUT
AUDIO OUT
HDMI OUT
VCR/DVD player
WARNING ►Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.
CAUTION ►Turn off all devices and unplug their power cords prior to
connecting them to projector. Connecting a live device to the projector may
generate extremely loud noises or other abnormalities that may result in
malfunction or damage to the device and the projector.
►Use appropriate accessory or designated cables. Ask your dealer about non-
accessory cables which may be required a specific length or a ferrite core by
the regulations. For cables with a core only at one end, connect the end with
the core to the projector.
►Make sure that devices are connected to the correct ports. An incorrect
connection may result in malfunction or damage to the device and the projector.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting power supply
Put the connector of the power cord into the
AC IN (AC inlet) of the projector.
1.
Firmly plug the power cord’s plug into the
outlet.
2.
AC IN
Power cord
WARNING ►Please use extra caution when connecting the power cord, as
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, consult
your dealer to get a new one.
• Only plug the power cord into an outlet whose voltage is matched to the power
cord. The power outlet should be close to the projector and easily accessible.
Remove the power cord for complete separation.
• Never modify the power cord.
Turning on the power
Make sure that the power cord is firmly and
correctly connected to the projector and the
outlet.
1.
STANDBY/ON button
POWER indicator
Remove the lens cover, and set the power
switch to the ON position (marked “
׀ ”). 2.
Press the STANDBY/ON button on the
projector or the remote control.
The projection lamp will light up and the POWER
indicator will begin blinking in green. When the
power is completely on, the indicator will stop
3.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
blinking and light in steady green.
ASPECT
AUTO SEARCH BLANK
MAGNIFY FREEZE
ON
PAGE
UP
VOLUME
㧗
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
POSITION
ENTER
ESC
RESET
Power switch
WARNING ►A strong light is emitted when the projector’s power is on. Do not look into
the lens of the projector or look inside of the projector through any of the projector’s openings.
NOTE • Please power on the projector prior to the connected devices.
• When the AUTO ON of the OPTION menu is set to the TURN ON, and the
power was turned off by the power switch last time, turning the power switch on
makes the projection lamp light on without pushing the STANDBY/ON button.
For more information, please see the “Operating Guide” in the CD.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the projector's elevator
When the place to put the projector is slightly uneven to
the left or right, use the elevator feet to place the projector
horizontally.
10°
Using the feet can also tilt the projector in order to project at a suitable angle to
the screen, elevating the front side of the projector within 10 degrees.
This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is
adjustable while pushing the elevator button on the same side as it.
1. Holding the projector, push the elevator buttons to loose the elevator feet.
2. Position the front side of the projector to the desired height.
3. Release the elevator buttons in order to lock the elevator feet.
After making sure that the elevator feet are locked, put the projector down
gently.
4.
If necessary, the elevator feet can be manually twisted to make more precise
adjustments. Hold the projector when twisting the feet.
5.
To loose an elevator foot, push the
To finely adjust, twist the foot.
elevator button on the same side as it.
CAUTION ►Do not handle the elevator buttons without holding the
projector, since the projector may drop down.
►Do not tilt the projector other than elevating its front within 10 degrees using
the adjuster feet. A tilt of the projector exceeding the restriction could cause
malfunction or shortening the lifetime of consumables, or the projector itself.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying the picture
Activate your signal source. Turn the signal
source on, and make it send the signal to
the projector.
1.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
MAGNIFY FREEZE
PAGE
UP
VOLUME
ON
㧗
VOLUME+ button
VOLUME- button
MUTE button
DOWN
OFF
Use the VOLUME +/VOLUME - buttons to
adjust the volume.
To have the projector silent, press the MUTE
button on the remote control.
KEYSTONE
MY BUTTON
MUTE
MENU
2.
1
2
POSITION
▲ cursor button
▼ cursor button
ENTER
ESC
RESET
Press the INPUT button on the projector.
3.
Each time you press the button, the
projector switches its input port in turn.
You can also use the remote control to
select an input signal. Press the VIDEO
button for selecting an input signal from the
COMPONENT (Y, Cb/Pb, Cr/Pr), VIDEO
or S-VIDEO port, or the COMPUTER
button for selecting an input signal from the
COMPUTER IN1, COMPUTER IN2 or HDMI
port.
INPUT button
VIDEO button
Press the ASPECT button on the remote
4.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
control. Each time you press the button,
the projector switches the mode for aspect
ASPECT
AUTO SEARCH BLANK
COMPUTER button
ASPECT button
MAGNIFY FREEZE
PAGE
UP
VOLUME
ON
㧗
DOWN
OFF
ratio in turn.
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
Use the zoom ring to adjust the screen
size.
6. Use the focus ring to focus the picture.
5.
POSITION
ENTER
ESC
RESET
Focus ring
Zoom ring
NOTE • The ASPECT button does not work when no proper signal is inputted.
• For the details of how to adjust the picture, please see the “Operating Guide”
in the CD.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning off the power
Press the STANDBY/ON button on the projector
STANDBY/ON button
POWER indicator
1.
or the remote control.
The message “Power off?” will appear on the
screen for about 5 seconds.
Press the STANDBY/ON button again while the
message appears.
The projector lamp will go off, and the POWER
indicator will begin blinking in orange. Then the
POWER indicator will stop blinking and light in
steady orange when the lamp cooling is complete.
2.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
MAGNIFY FREEZE
ON
PAGE
UP
VOLUME
㧗
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
POSITION
ENTER
ESC
RESET
Make sure that the POWER indicator lights in
3.
steady orange, and set the power switch to the
OFF position (marked “O”). Attach the lens cover.
Do not turn the projector on for about 10 minutes
or more after turning it off. Turning the projector on
again too soon could shorten the lifetime of some
consumable parts of the projector.
Power switch
WARNING ►Do not touch around the lamp cover and the exhaust vents
during use or just after use, since it is too hot.
►Remove the power cord for complete separation. The power outlet should be
close to the projector and easily accessible.
NOTE • Please power off the projector after any connected devices are powered off.
•
This projector has the AUTO OFF function that can make the projector turn off
automatically. For more information, please see the “Operating Guide” in the CD.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the lamp
A lamp has finite product life. Using the lamp for long periods of time could cause
the pictures darker or the color tone poor. Note that each lamp has a different
lifetime, and some may burst or burn out soon after you start using them.
Preparation of a new lamp and early replacement are recommended. To prepare
a new lamp, make contact with your dealer and tell the lamp type number.
Type number : 456-8755H
Turn the projector off, and unplug the power cord.
Allow the projector to cool for at least 45 minutes.
Lamp cover
1.
2.
Prepare a new lamp. If the projector is mounted on
a ceiling, or if the lamp has broken, also ask the
dealer to replace the lamp.
In case of replacement by yourself, follow the following
procedure.
Loosen the screw (marked by arrow) of the lamp
3.
cover and then slide and lift the lamp cover to the
side to remove it.
Loosen the 2 screws (marked by arrow) of the
lamp, and slowly pick up the lamp by the handles.
4.
Insert the new lamp, and retighten firmly the
5.
2 screws of the lamp that are loosened in the
previous process to lock it in place.
Handles
While putting the interlocking parts of the lamp
6.
cover and the projector together, slide the lamp
cover back in place. Then firmly fasten the screw of
the lamp cover.
Turn the projector on and reset the lamp time
using the LAMP TIME item in the OPTION menu.
7.
(1) Press the MENU button to display a menu.
(2) Point at the Go to Advanced Menu … in the menu
using the ▼/▲ button, then press the ► button.
(3) Point at the OPTION in the left column of the menu
using the ▼/▲button, then press the ► button.
(4) Point at the LAMP TIME using the ▼/▲ button,
then press the ► button. A dialog will appear.
(5) Press the ▲ button to select RESET on the dialog.
It performs resetting the lamp time.
CAUTION ►Do not touch any inner space of the projector, while the lamp
is taken out.
NOTE • Please reset the lamp time only when you have replaced the lamp,
for a suitable indication about the lamp.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
WARNING ►The projector uses a high-pressure mercury glass lamp. The
lamp can break with a loud bang, or burn out, if jolted or scratched, handled
while hot, or worn over time. Note that each lamp has a different lifetime, and
some may burst or burn out soon after you start using them. In addition, when
the bulb bursts, it is possible for shards of glass to fly into the lamp housing,
and for gas containing mercury to escape from the projector’s vent holes.
►About disposal of a lamp: This product contains a mercury lamp; do not put
it in a trash. Dispose of it in accordance with environmental laws.
• For product disposal, consult your local government agency
For more information, ask your dealer.
• If the lamp should break (it will make a loud bang when it does),
unplug the power cord from the outlet, and make sure to request a
replacement lamp from your local dealer. Note that shards of glass
could damage the projector’s internals, or cause injury during handling,
so please do not try to clean the projector or replace the lamp yourself.
• If the lamp should break (it will make a loud bang when it does),
Disconnect
the plug
ventilate the room well, and make sure not to breathe the gas that
comes out of the projector vents, or get it in your eyes or mouth.
• Before replacing the lamp, turn the projector off and unplug the power
from the
power
outlet
cord, then wait at least 45 minutes for the lamp to cool sufficiently.
Handling the lamp while hot can cause burns, as well as damaging the lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
• Do not open the lamp cover while the projector is suspended from
a ceiling. This is dangerous, since if the lamp’s bulb has broken, the
shards will fall out when the cover is opened. In addition, working in
high places is dangerous, so ask your local dealer to have the lamp
replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp
replacing, make sure that the screws are screwed in firmly. Loose
screws could result in damage or injury.
• Use only the lamp of the specified type.
• If the lamp breaks soon after the first time it is used, it is possible
that there are electrical problems elsewhere besides the lamp. If this
happens, consult your local dealer or a service representative.
•
Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• Using the lamp for long periods of time, could cause it dark, not to light
up or to burst. When the pictures appear dark, or when the color tone
is poor, please replace the lamp as soon as possible. Do not use old
(used) lamps; this is a cause of breakage.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and replacing the air filter
Please check and clean the air filter periodically. When the indicators or a message
prompts you to clean the air filter, comply with it as soon as possible. The air filter has two
kinds of filters inside. Replace the filters when they are damaged or too soiled. To prepare
the new filters, make contact with your dealer and tell the following type number.
Type number : MU05611
When you replace the lamp, please replace the air filter.
Filter cover
An air filter of specified type will come together with a
replacement lamp for this projector.
Turn the projector off, and unplug the power cord. Allow
the projector to sufficiently cool down.
Use a vacuum cleaner on and around the filter cover.
1.
Filter cover knobs
Filter unit
2.
3.
4.
Pull the filter cover knobs while lifting it, to take the filter
unit off.
Use a vacuum cleaner for the filter vent of the projector
and both sides of the filter unit.
If the filters are damaged or too soiled, replace them according
to the following procedure number 5 to 7. Otherwise, please
jump to the procedure number 8.
Filter frame
Pull the filter frame’s knob up while holding the filter
5.
cover to remove the filter frame, then take the filters out.
Filter (finer meshed)
Filter (larger meshed)
Set new filters where former filters were. Put the larger
6.
meshed filter into a filter cover first. Then put the finer
meshed filter on the larger meshed one.
Put the filter frame back where it was.
7.
8.
9.
Put the filter unit back into the projector.
Turn the projector on and reset the filter time using the
FILTER TIME item in the EASY MENU.
(1) Press the MENU button to display a menu.
Filter cover
(2) Point at the FILTER TIME using the ▼/▲ button, then press the ► button. A dialog will appear.
(3) Press the ▲ button to select RESET on the dialog. It performs resetting the filter time.
WARNING ►Before taking care of the air filter, make sure the power cable
is not plugged in, then allow the projector to cool sufficiently.
►
Use only the air filter of the specified type. Do not use the projector without the
air filter or the filter cover. It could result in a fire or malfunction to the projector
Clean the air filter periodically. If the air filter becomes clogged by dust or the like,
.
►
internal temperatures rise and could cause a fire, a burn or malfunction to the projector.
NOTE • Please reset the filter time only when you have cleaned or replaced
the air filter, for a suitable indication about the air filter.
• The projector may display the message such as “CHECK THE AIR FLOW” or
turn off the projector, to prevent the internal heat level rising.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD manual
The other manuals for this product are written into the included CD-ROM titled
“User’s Manual (detailed)”. Before using the CD-ROM, please read the following
to ensure the proper use.
System requirements
The system for using the CD-ROM requires the following.
Windows®:
OS:Microsoft® Windows® 98, Windows® 98SE,
Windows NT®4.0, Windows® Me,
Windows® 2000/Windows® XP or later
CPU:Pentium® processor 133MHz / Memory:32MB or more
OS:Mac OS® 10.2 or later
Macintosh®:
CPU:PowerPC® / Memory:32MB or more
CD-ROM drive: 4x CD-ROM drive
Display:
256 color / 640x480 dots resolution
Applications:
Microsoft® Internet Explorer®4.0 and
Adobe® Acrobat® Reader® 4.0 or later
How to use the CD
1. Insert CD into PC’s CD-ROM drive.
Windows®:
In a while, Web browser automatically starts. Start up
window comes up.
Macintosh®:
(1) Double-click on the ”Projectors” icon appeared on the
desktop screen.
(2) When “main.html” file is clicked, Web browser will start
and Initial window will appear.
2. Click the model name of your projector first, and then click language you want
from the displayed list. The User’s manual (detailed) will open.
CAUTION ►Only use the CD-ROM in a computer CD drive. The CD-
ROM is designed for PC use only. NEVER INSERT THE CD-ROM INTO A
NON-COMPUTER CD PLAYER! Inserting the CD-ROM into an incompatible
CD drive may produce a loud noise, which in turn MAY RESULT IN EAR AND
SPEAKER DAMAGE!
• After using CD-ROM, please put it into CD case and keep it. Please keep
the CD neither in direct sunlight nor in a high temperature and high humidity
environment.
NOTE • The information in the CD-ROM is subject to change without notice.
• No responsibility is taken for any obstacle and defect to hardware and
software of your PC as a result of the use of the CD-ROM.
• All or Any part of the information in the CD-ROM must not be copied,
reproduced or republished without notice to our company.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory notices
Declaration of Conformity
Trade name
HITACHI
Model Number
Responsible Party
Address
CP-WX410
Hitachi Home Electronics (America), Inc.
900 Hitachi way, Chula Vista, CA 91914-3556 U.S.A.
Telephone Number +1 -800-225-1741
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC Statement warning
WARNING: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC
(Federal Communication Commission) equipment provided that the following conditions
are met. Some cables have to be used with the core set. Use the accessory cable or a
designated-type cable for the connection. For cables that have a core only at one end,
connect the core to the projector.
CAUTION: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
For the Customers in CANADA
NOTICE: This Class B digital apparatus complies with Canadian ICES-003.
(continued on next page)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory notices (continued)
Information for users applicable in European Union countries
This symbol on the product or on its packaging means that your electrical and
electronic equipment should be disposed at the end of life separately from your
household wastes. There are separate collection systems for recycling in EU.
For more information, please contact the local authority or the dealer where you
purchased the product.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Item
Specification
Product name
Liquid crystal projector
1.5cm (0.59 type)
TFT active matrix
Panel size
Liquid
Crystal
Panel
Drive system
Pixels
1,024,000 pixels (1280 horizontal x 800 vertical)
Lens
Zoom lens, F = 1.6 ~ 1.8, f = 18.9~ 22.6 mm (approximately)
Lamp
230W UHB
Speaker
10W x 1
Power supply
AC 100-120V/3.5A, AC220-240V/1.5A
320W
Power consumption
Temperature range
5 ~ 35°C (Operating)
340 (W) x 100 (H) x 270 (D) mm
* Not including protruding parts. Please refer to the following figure.
Size
Weight (mass)
approx. 3.5 kg
Computer input port
COMPUTER IN1 ............................................D-sub 15 pin mini x1
COMPUTER IN2 ............................................D-sub 15 pin mini x1
Computer output port
MONITOR OUT ..............................................D-sub 15 pin mini x1
Video input port
Y, Cb/Pb, Cr/Pr (Component video) .................................... RCA x3
S-VIDEO...............................................................mini DIN 4 pin x1
VIDEO ................................................................................. RCA x1
HDMI input port
Ports
HDMI .................................................................HDMI connector x1
Audio input/output port
AUDIO IN1.................................................................Stereo mini x1
AUDIO IN2.................................................................Stereo mini x1
AUDIO IN3........................................................................... RCA x2
AUDIO OUT...............................................................Stereo mini x1
Others
USB..................................................................................USB-B x1
CONTROL................................................................ D-sub 9 pin x1
Lamp: 456-8755H
Air filter: MU05611
Optional parts
* For more information, please consult your dealer.
3
A U D I O I N
A U D I O I N
S - V I D E O
U S B
C O N T R O L
A U D I O O U T
H D M I
T
M O N I T
2
O R O U
C O M P U T 1 E R I N
C O M P U T E R I N
340mm
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and after-service
If an abnormal operation (such as smoke, strange odor or excessive sound) should occur,
stop using the projector immediately. Otherwise if a problem occurs with the projector,
first refer to the “Troubleshooting” of the “Operating Guide” in the CD and run through the
suggested checks.
If this does not resolve the problem, please consult your dealer or service company. They will
tell you what warranty condition is applied.
Please check the following web address where you may find the latest information for this
projector.
http://www.dukcorp.com/audiovisual
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
Trademark acknowledgment
• Mac, Macintosh and Mac OS are registered trademarks of Apple Inc.
• Pentium is a registered trademark of Intel Corp.
• Adobe and Acrobat, Reader are registered trademarks of Adobe Systems Incorporated.
• Microsoft and Internet explorer, Windows, Windows NT are registered trademarks of
Microsoft Corporation.
• PowerPC is a registered trademark of International Business Machines Corporation.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
All other trademarks are the properties of their respective owners.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|