model
1200/5
Download from Www.Somanuals.com. All Manuals Search And Download.
CONGRATULATIONS
Congratulations for choosing a Directed
Audio power amplifier from Directed
Electronics, the industry leader in high
quality automotive security and audio
equipment since 1990.
enthusiast with years of high-quality
audio reproduction.
Directed Audio power amplifiers come
with a two-year limited warranty if
installed by an authorized Directed
dealer. If not installed by an authorized
dealer, Directed Audio power amplifiers
are covered by a one-year, parts-and-
labor limited warranty.
Directed Audio power amplifiers
continue to set new standards of perfor-
mance, reliability, and affordability in
the mobile electronics industry.
Featuring high-efficiency MOSFET power
supplies, flexible on-board crossovers,
and state of the art audio design,
Directed Audio power amplifiers will
excite and delight the mobile sound
Be sure to retain your original sales
receipt and refer to the warranty section
of this guide for full details about your
coverage.
TABLE OF CONTENTS
Limited Two-Year Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . .4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Front Panel Connections/Status LED . . . . . . . . . . . . . . . . . . . . . . . . . .8
Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Top Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Top Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Speaker Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Combined Amplifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Parallel Synced Gain Connections/Settings . . . . . . . . . . . . . . . . . . . . .14
External Synced Bridged Connections/Settings . . . . . . . . . . . . . . . . . . .16
Crossover Settings and Gain Adjustment . . . . . . . . . . . . . . . . . . . . . . .18
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED TWO-YEAR CONSUMER WARRANTY
Directed Electronics, Inc. promises to the
original purchaser, to replace this product
should it prove to be defective in workman-
ship or material under normal use, for a
period of two years from the date of
purchase by the dealer as indicated by the
date code marking of the product
PROVIDED the product was installed by an
authorized Directed dealer. During this two -
year period, there will be no charge for this
replacement PROVIDED the unit is returned
to Directed, shipping pre-paid. If the unit is
installed by anyone other than an autho-
rized Directed dealer, the warranty period
will be one year from the date of purchase
by the dealer as indicated by the date code
marking of the product. During this one-year
period there will be no charge for this
replacement PROVIDED the unit is returned
to Directed, shipping pre-paid. This warranty
is non-transferable and does not apply to
any unit that has been modified or used in a
manner contrary to its intended purpose,
and does not cover damage to the unit
caused by installation or removal of the unit.
This warranty is void if the product has been
damaged by accident or unreasonable use,
neglect, improper service or other causes
not arising out of defects in materials or
construction. ALL WARRANTIES INCLUDING
BUT NOT LIMITED TO EXPRESS
WARRANTY, IMPLIED WARRANTY,
WARRANTY OF MERCHANTABILITY,
FITNESS FOR PARTICULAR PURPOSE, AND
WARRANTY OF NON-INFRINGEMENT OF
INTELLECTUAL PROPERTY ARE EXPRESSLY
EXCLUDED TO THE MAXIMUM EXTENT
ALLOWED BY LAW, AND DIRECTED
NEITHER ASSUMES NOR AUTHORIZES
ANY PERSON TO ASSUME FOR IT ANY
LIABILITY IN CONNECTION WITH THE
SALE OF THE PRODUCT. DIRECTED HAS
ABSOLUTELY NO LIABILITY FOR ANY AND
ALL ACTS OF THIRD PARTIES INCLUDING
ITS AUTHORIZED DEALERS OR
INSTALLERS. Unit must be returned to
Directed, postage pre-paid, with: consumer’s
name, telephone number, and address,
authorized dealer’s name and address, and
product description. IN ORDER FOR THIS
WARRANTY TO BE VALID, YOUR UNIT
MUST BE SHIPPED WITH PROOF OF
INSTALLATION BY AN AUTHORIZED
DIRECTED DEALER. ALL UNITS RECEIVED
BY DIRECTED FOR WARRANTY REPAIR
WITHOUT PROOF OF DIRECTED DEALER
INSTALLATION WILL BE COVERED BY THE
LIMITED ONE-YEAR PARTS AND LABOR
WARRANTY. Note: This warranty does not
cover labor costs for the removal and rein-
stallation of the unit. BY PURCHASING
THIS PRODUCT, THE CONSUMER AGREES
AND CONSENTS THAT ALL DISPUTES
BETWEEN THE CONSUMER AND Directed
SHALL BE RESOLVED IN ACCORDANCE
WITH CALIFORNIA LAWS IN SAN DIEGO
COUNTY, CALIFORNIA.
4
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
„ Dual high-speed MOSFET switching
„ Remote subwoofer level control and
power supplies.
switchable 8 dB bass EQ function.
„ Complimentary bipolar outputs (ch
1-4), and high-current MOSFET
outputs (sub channel).
„ Two, four, and six channel input
allows full access to source or
processor output functions.
„ Five channel expandable architec-
ture supports single or multiple amp
system designs.
„ Master/slave function allows
synced bridged or parallel operation
with model 750d.
„ Thermal, DC offset, reverse polarity,
and short circuit protection with
status LED.
„ Summed stereo full-range RCA
output jacks.
„ Gold-plated wire terminals and RCA
connectors ensure maximum signal
transfer.
„ Top-mounted controls are easily
accessed for system tuning.
„ Dual continuously variable 12
dB/octave two-way active
crossovers (ch 1-4).
„ Rugged one-piece extruded heat
sink finished with injection-molded
mounting feet.
„ Continuously variable 24 dB/
octave low-pass crossover (sub
channel).
„ Switchable 30Hz, 24 dB/octave
subsonic filter and phase invert
switch (sub channel).
WARNING
High-powered car audio
systems may produce sound
pressure levels that exceed the
threshold at which hearing loss may
result.
They may also impair a driver’s ability to
hear traffic sounds or emergency vehi-
cles. Use common sense and practice
safe listening habits when listening to or
adjusting your audio system.
5
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION GUIDELINES
1. Please read this owner’s manual
carefully before installing this ampli-
fier.
battery terminal. Use a fuse or
circuit breaker rated slightly more
than the on-board fuse(s) of the
amplifier(s). The gauge of power
wire used should take into account
the total current draw of the
system, and the length of wire
used. IASCA and other auto sound
competition organizations have
charts available for this; you can
also find a chart in the MECP study
guide. Minimum wire gauge recom-
mendations for the individual ampli-
fiers are listed on the specification
page. Always use the same gauge
wire for the amplifier ground that
you use for the power wire. Be sure
to examine the battery ground
cable of the vehicle, and if neces-
sary, upgrade it by adding an addi-
tional ground wire that is the same
gauge as the amplifier’s power
wire. Remember, the amplifier can
only deliver its rated output when it
is not current limited by the power
and ground supply wires.
2. Disconnect the battery ground
terminal prior to making any elec-
trical connections.
3. Check for any hazards or obstruc-
tions such as gas tanks, fuel or
brake lines, and wiring harnesses
before mounting the amplifier.
4. Pick a mounting location that will
provide adequate access and venti-
lation and protect the amplifier
from heat, moisture, and dirt.
5. Avoid sharp metal areas when
routing cables to the amplifier, and
run RCA cables away from the
power cables and other potentially
noisy car harnesses.
6. The amplifier should be grounded
with a short, heavy gauge wire
connected directly to the car at a
bare metal surface, preferably
scraped body sheet metal. Do not
use factory ground locations, seat
bolts, or brackets that are spot
welded.
8. This amplifier is designed to drive a
speaker load that measures from 2-
8 ohms (sub ch 1-4 ohms). Keep in
mind that heat is the long-term
enemy of automotive electronics
7. Always fuse your power connection
within eight to ten inches of the
6
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
and the lower your speaker load,
the more heat is generated. For low
impedance speaker applications or
restricted ventilation installations,
an external cooling fan may be
advisable.
10. Due to the high-frequency MOSFET
switching power supply, filtering the
power cable is not generally
required (remember that the amp
can’t deliver full output if the power
supply is restricted). Proper
grounding of the signal source is
mandatory for the amplifier to
reach its performance peak. If the
RCA inputs are not grounded
adequately via the signal source,
electrical noise from the vehicle
may be picked up in the system.
9. Battery and ground connections to
the vehicle should be made with
crimped ring terminals of the appro-
priate size (surface area is what
counts); soldering the terminals
after crimping is also recom-
mended.
7
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT PANEL CONNECTIONS/STATUS LED
RCA Input Jacks -
RCA Bridge Output Jack
- This output
1.
Accepts line level
5.
outputs from head units or signal
processors between 150mV and 8
volts.
sends an out-of-phase signal to a
750d slave amplifier when
connected in the External Synced
Bridged combination. (Refer to the
Combined Amplifiers section of this
guide.)
RCA Sub Input Jacks
2.
- Accepts line
level outputs from head units or
signal processors between 150mV
and 8 volts for the subwoofer
section of the amplifier.
Status LEDs
6.
- The Power LED will
light GREEN to indicate the amplifier
is on and operating normally. The
GREEN LED will turn off and the
Protection LED will light RED when
the amplifier has shut itself down
due to speaker short circuit, DC
offset or overheating.
RCA Output Jacks -
3.
4.
These pass
through RCA jacks can be used to
send a signal to a second amplifier. It
is the summed stereo output of the
one through four channel inputs of
the amplifier.
Remote Sub Level Control
7.
- Controls
RCA Sync Out Jack
- This RCA jack
the subwoofer amplifier gain
controls from a remote location for
ease of adjustment during listening.
sends a synced, or in-phase, gain
matched signal to a 750d slave
amplifier when connected in the
Parallel Synced Gain combination.
(Refer to the Combined Amplifiers
section of this guide.)
Warning: DO NOT connect a level control knob from other
manufacturers to the Remote Sub Level Control of
any Directed amplifier. Even though the connectors
fit properly, the control knob and connector pin
positions may be different and the amplifier will be
damaged.
FIGURE 1—AMPLIFIER CONNECTIONS 1200/5 FRONT
4
5
1
2
3
6
7
1+2
3+4
SUB
1-4 OUT
SUB OUT
S
SYNC OUT
R
L
POWER
REMOTE
BRIDGE OUT
PROTECTION
8
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR PANEL CONNECTIONS
Sub Out Terminals
1.
2.
3.
- Connect
turns on the amplifier when (+) 12
volt is applied to it. Connect it to
the remote turn on lead of the head
unit or signal source. If a (+) 12
volt remote turn on lead is not
available, Remote Power Adapter
(P/N #55000) can be used to
supply a remote turn on signal. DO
NOT connect this terminal to
constant (+) 12 volt.
subwoofers to these terminals.
(Refer to the Speaker Wiring
Diagrams section of this guide.)
Speaker Out Terminals
- Connect
the speakers to these terminals.
(Refer to the Speaker Wiring
Diagrams section of this guide.)
Power Fuses -
These fuses protect
the amplifier against internal elec-
trical damage and are meant to
protect the amplifier only. All other
power connections should be fused
at the source.
Ground -
6.
Connect this terminal
directly to the sheet metal chassis
of the vehicle, using the shortest
wire necessary to make this
connection. Always use wire of the
same gauge or larger than the (+)
12 volt power wire. The chassis
connection point should be scraped
free of paint and dirt. Use only
quality crimped and/or soldered
connectors at both ends of this
wire. DO NOT connect this terminal
directly to the vehicle battery
ground terminal or any other
factory ground points.
(+) 12 Volt Power
4.
- Connect this
terminal through a FUSE or CIRCUIT
BREAKER to the positive terminal of
the vehicle battery or the positive
terminal of an isolated audio
system battery.
WARNING: Always protect this power wire by installing a fuse
or circuit breaker of the appropriate size within 12
inches of the battery terminal connection.
Remote Turn On
5.
- This terminal
FIGURE 2—AMPLIFIER CONNECTIONS 1200/5 REAR
1
6
5
4
2
3
REAR
R
FRONT
R
FUSE
3
SUB OUT
40A
x
BATT
REM
GND
L
L
9
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
TOP PANEL CONTROLS
Input Gain Adjustment
Subsonic Frequency Switch
- Sets
1.
- Controls
6.
7.
amplifier sensitivity and is used to
match the input level of the ampli-
fier to the output level of the signal
source.
the cutoff point for subsonic
frequencies at 30 Hz. Frequencies
below will be attenuated by 24db
per octave.
Crossover Selection Switch
2.
-
Sub Input Switch
- Controls where
Controls the type of filter for the on-
board active crossovers. FLAT does
not attenuate any frequencies and is
for full-range speaker systems. HPF
attenuates low frequencies and is
used for mid-range speakers and
tweeters. LPF attenuates high
frequencies and is used for
subwoofers speakers.
the subwoofer section of the ampli-
fier gets its signal. If the SUB INPUT
switch is in the ON position the
subwoofer section of the amplifier
will get its signal internally summed
from the channels one through four
RCA jacks, and the SUB RCA jacks
do not need input. If in the OFF
position the SUB RCA jacks must
have input.
Crossover Frequency Adjustment
3.
4.
5.
-
Adjusts the crossover point for the
on-board active crossovers.
Input Parallel Switch
8.
- Controls the
input signal to the indicated chan-
nels. If the 3+4 switch is ON, chan-
nels three and four will derive their
signal from channels one and two
RCA jacks and no input is needed. If
the 3+4 switch is OFF, channels
three and four RCA jacks must have
input.
Sub Phase Switch
- Changes the
phase of the subwoofer speaker
output by 180 degrees
Bass EQ Switch -
Adds 8db of addi-
tional boost to the subwoofer output
when active.
10
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 3—AMPLIFIER CONTROLS 1200/5 TOP
5
6
4
PHASE
BASS EQ
SUBSONIC
0
180
FREQ
OFF
ON
OFF
ON
FREQ
FREQ
3
2
50Hz50Hz305H0z0Hz500Hz250Hz
1+2
3+4
SUB
LPF
HPF
LPF
HPF
FLAT
FLAT
GAIN
GAIN
GAIN
1
MIN
MAX
MIN
ON
MAX
MIN
ON
MAX
7
8
OFF
3+4
INPUT
OFF
SUB
INPUT
TOP PANEL FEATURES
Control Panel Cover
Remove/Install
The gain and filter controls are located
under a control panel cover on top of
the amplifier. The control panel cover
must be removed to gain access to the
gain and filter controls.
Four Allen-head screws hold the control
panel cover to the amplifier top panel,
one at each corner. They can be
removed with the wrench supplied in
the hardware pack.
11
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER WIRING DIAGRAMS
Five channel operation (top view)
Three channel operation (top view)
12
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
COMBINED AMPLIFIERS
External Synced Bridged
The Directed 1200/5 channel five
subwoofer section can be combined with The External Synced Bridged combination
a 750d in a master/slave combination includes a master amplifier and a slave
for increased power and accurate level amplifier.
matching. They are the Parallel Synced
In this master/slave combination the
Gain and External Synced Bridged combi-
master amplifier’s pre-amp controls
nations.
remain active and the slave amplifier’s
pre-amp is bypassed. This allows the
master amplifier to control gain, filter,
and sub-level on both amplifiers.
NOTE:
The Directed 1200/5 is always the master amplifier
in these combinations.
Parallel Synced Gain
The Parallel Synced Gain combination
includes a master amplifier and a slave
amplifier.
This combination allows the amplifiers to
drive common subwoofer loads while
being synced together via an out-of-
phase audio pre-amp signal from the
master amplifier. In this wiring configura-
tion the master amplifier sends the posi-
tive signal to the speaker while the slave
amplifier sends the negative signal,
making an externally bridged speaker
combination. (Refer to External Synced
In this master/slave combination the
master amplifier’s pre-amp controls
remain active and the slave amplifier’s
pre-amp is bypassed. This allows the
master amplifier to control gain, filter,
and sub-level on both amplifiers.
The Parallel Synced Gain combination Bridged section of this guide for ampli-
allows the amplifiers to drive their own fier and speaker connection diagrams.)
separate subwoofer(s) while being
Combined Amplifiers Gain
and Filter Settings
synced together via an in-phase audio
pre-amp signal from the master amplifier.
Set the Subsonic, EQ, and other filter
Woofer wiring connections to the ampli-
settings on the master amplifier to the
fier subwoofer outputs in this combina-
positions that achieve the best sound
tion should be standard in-phase configu-
quality. Follow the adjustment guidelines
rations, creating a parallel speaker
discussed in the Crossover and Gain
combination. (Refer to Parallel Synced
Adjustment section of this guide.
Gain section of this guide for amplifier
and speaker connection diagrams.)
13
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
PARALLEL SYNCED GAIN CONNECTIONS/SETTINGS
Input/Output Signal
Slave/Master Switch
- Set the
1.
- Connect these 4.
RCA jacks as described in the Front
Panel Connections/Controls section
of this guide.
slave/master switch of the 750d to
the slave position. This will put the
I/O RCA jack in the SLAVE IN mode
so it will accept the audio signal
from the 1200/5’s sync out RCA
jack.
Remote Sub Level Control
2.
- Connect
the Remote Sub Level control to the
1200/5 only. The 1200/5 control
panel subwoofer adjustments are 5.
used first to set the overall gain for
all synced amplifiers, then the
Remote Sub Level control can adjust
the gain of all synced amplifiers by
adjusting its control knob.
Subwoofer Speaker Connection
- In
this amplifier combination each
amplifier must drive its own separate
subwoofer(s). Connect the speaker
terminals of each amplifier to any
combination of one or more
subwoofers that results in nominal
impedance between 1 and 4 ohms.
Make sure that each amplifier sees
the same speaker impedance.
Signal Connection
3.
- Connect an RCA
cable between the SYNC OUT RCA
jack of the 1200/5 and the SLAVE
IN RCA jack of the slaved 750d as
shown in Figure 5.
14
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 5—PARALLEL SYNC GAINED 750d/1200/5
Master (1200/5)
1
Do Not Use
1+2
3+4
SUB
1-4 OUT
SUB OUT
SYNC OUT
R
L
POWER
REMOTE
BRIDGE OUT
PROTECTION
2
Slave (750d)
MIN
MAX
SUB LEVEL
3
INPUT
I
SLAVE
MASTER
SLAVE IN
SYNC OUT
R
L
REMOTE
BRIDGE OUT
Do Not Use
4
Do Not Use
Speaker Wiring (top view)
MASTER
1200/5
-
SUB
SUBWOOFER
+
-
+
SLAVE
750D
-
-
5
+
-
+
+
NOTE:
The dual + and -- sub-out terminals of the 750d are paralleled internally and the
combined load impedance should be taken into consideration when connecting multiple
subwoofers.
15
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
Input/Output Signal
1.
2.
- Connect
these RCA jacks as described in the
Front Panel Connection/Controls
section of this guide.
Remote Sub Level Control
- Connect
the Remote Sub Level control to the
1200/5 only. The 1200/5 control
panel subwoofer adjustments are
used first to set the overall gain for
all synced amplifiers, then the
Remote Sub Level control can
adjust the gain of all synced ampli-
fiers by adjusting its control knob.
Signal Connection
3.
4.
- Connect an RCA
cable between the BRIDGE OUT
jack of the 1200/5 and the SLAVE
IN jack of the slaved 750d as
shown in Figure 6.
Slave/Master Swj 1 Tr T* (u)Tj 0 Tr 0.3607 0 TD (t)T552R61ront Panel Connection/Cont
16
© 2003 Directed Electronics, Inc
FIGURE 6—EXTERNAL SYNC BRIDGED 600d/1100d5
Master (1200/5)
1
Do Not Use
1+2
3+4
SUB
1-4 OUT
SUB OUT
SLAVE
MASTER
SYNC OUT
R
L
POWER
REMOTE
BRIDGE OUT
PROTECTION
2
Slave (750d)
MIN
MAX
SUB LEVEL
3
INPUT
I
SLAVE
MASTER
SLAVE IN
SYNC OUT
R
L
REMOTE
BRIDGE OUT
Do Not Use
Do Not Use
4
Speaker Wiring (top view)
MASTER
1200/5
SUB
-
+
SLAVE
750D
12 gauge
+
-
5
+
-
-
12 gauge
+
NOTE:
The dual + and -- sub-out terminals of the 750d are paralleled internally and the
combined load impedance should be taken into consideration when connecting multiple
subwoofers.
17
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
CROSSOVER SETTINGS AND GAIN ADJUSTMENT
Your Directed Audio power amplifier needs to be adjusted carefully to achieve
maximum performance. These are some guidelines to follow when fine-tuning the
amplifier.
„ For full-range and simultaneous stereo/mono bass applications, the crossover
selection switch should be set to FLAT. If the amplifier is driving your subwoofers,
set the switch to LPF, and for mid-bass/midrange output, set to HPF.
„ The crossover frequency control needs to be adjusted to suit your particular system.
For subwoofer applications, try to keep the setting low enough to prevent the
image smearing (you should not be able to hear male voices from the subwoofer)
but not so low as to create a gap between the subwoofer and the mid-
bass/midrange speakers. For mid-bass/midrange settings, try to keep the setting
low enough to keep your sound stage in front of you, without overdriving the
speaker. It will be to your advantage to spend some extra time with this adjust-
ment, listening to familiar music or system set-up discs to achieve the kind of
musical reproduction that you prefer.
„ The gain adjustment allows you to set proper signal match for clean, quiet ampli-
fier operation. For full-range and simultaneous stereo/mono bass applications,
start by playing some music you are familiar with. With the gain adjustment on
the amplifier in the middle of its rotation, bring up the volume on your head unit
to the 3/4 volume setting or until you start to hear distortion or clipping. If you
hear distortion before you reach the 3/4 volume setting of your head unit, reduce
the gain setting on the amplifier and start to raise the head unit volume again.
When you can listen to the music at or slightly above 3/4 on your head unit
without audible distortion, slowly raise the gain of the amplifier until distortion is
heard, then back off the gain until the distortion is not audible. This setting will
allow you to reach full output with all but the quietest of source material, while
avoiding excessive noise in the system.
„ For systems using the Remote Sub Level Adjustment, increase the subwoofer gain
on the amplifier by 25% and set the Remote Sub Level knob to the center position
after making all system gain and filter adjustments. This will give the Remote Sub
Level Control a wider range of adjustment to the subwoofer output.
„ The same procedure should be used for adjusting the amplifier when the on-board
crossover is set to LPF or HPF, but you will also have to take into consideration the
effect that gain adjustment has on system frequency response and imaging.
Again, plan on spending some time with music that you know, getting the gain
and crossover settings the way you like. Test discs and analyzers may help with this
process, but in the end it's your ears that count - listen to the music!
18
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Directed model 1200/5 Ch 1-4 Sub Ch.
75
watts
275
watts
RMS continuous power per channel, Channels 1-4 driven into
4 ohms from 20 to 20,000 Hz, with less than 0.08% total
Harmonic Distortion @ 14.4 VDC. Sub channel driven into 4
ohms from 20-250 Hz, with less than 0.4% THD @ 14.4 VDC.
RMS continuous power per channel, Channels 1-4 driven into
2 ohms from 20 to 20,000 Hz, with less than 0.1% Total
Harmonic Distortion @ 14.4 VDC. Sub channel driven into 2
ohms from 20-250 Hz, with less than 0.6% THD @ 14.4 VDC.
125
watts
400
watts
RMS continuous power, 3-channel operation, channels 1-4
bridged into 4 ohms from 20 to 20,000 Hz, with less than
0.1% Total Harmonic Distortion @ 14.4 VDC. Sub channel
driven into 1 ohm from 20-250 Hz, with less than 0.6% THD
@ 14.4 VDC.
250x2
watts
600
watts
Dynamic power rating (IHF-202 Standard) at minimum load
1300 watts
Signal-to-Noise Ratio
Greater than 95 dB (Ch 1-4),
80dB (sub)
Frequency Response
20-20,000 Hz 0.5 dB
(Ch 1-4)
Damping Factor @ 4 ohm
Greater than 100 (Ch 1-4),
50 (sub)
Crossover (Ch 1-4)
Switchable high or low pass
12 dB/octave, continuously
variable 50 to 500 Hz
Subwoofer Crossover
Low pass 24 dB/octave,
variable 30 to 250Hz
Bass Equalization
Input Impedance
Input Sensitivity
Switchable 8 dB/octave,
20K ohms
Variable from 150 mV to
8 volt
Output Impedance
(ch 1-4)
2 to 8 ohms, stereo
4 to 8 ohms, bridged
1 to 4 ohms
(Sub ch.)
Supply Voltage
Fusing and Power
10 to 16 VDC
120A
Minimum Cable Requirements (AWG)
(Per amp, trunk mounted)
#4
19
© 2003 Directed Electronics, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
The company behind this system is Directed Electronics, Inc.
Since its inception, Directed has had one purpose, to provide customers with the
finest vehicle security, car stereo products, rear seat entertainment, and accessories
available. The recipient of more than 20 patents in the field of advanced electronic
technology, Directed is ISO 9001 registered.
Directed Electronics, Inc.
Vista, California 92081
Directed® is committed to delivering world-class quality
products and services that excite and delight our customers.
Directed is a proud member of
Quality Directed products are sold and serviced throughout North America and around the world
Call 800 274 0200 for more information about our products and services
© 2003 Directed Electronics, Inc.
-
All rights reserved
-
G45059 11/03
Download from Www.Somanuals.com. All Manuals Search And Download.
|