NAVIGATION ANd CONTROLS
SET-uP LOCAL VIEWING ON YOuR PC
BASIC SETuP
BASIC SETuP
Right for Business
BASIC INSTALLATION GuIdE
BASIC INSTALLATION GuIdE
BASIC INSTALLATION GuIdE
LOCAL VIEWING INSTALLATION GuIdE
Time: 20 Minutes Hand Tools Skills - Easy
Time: 20 Minutes Hand Tools Skills - Easy
Time: 20 Minutes Skills - Easy
Time: 30 Minutes Hardware
Skills - Intermediate
PC/Router
STEP 1
STEP 1
STEP 2
STEP 3
CONTINuEd
This step relates to remote viewing over the LAN (local area network)
by using a PC located on the same network as that of the DVR.
Quick Setup
disabling Quick Setup
Connecting Cameras (not included)
using the Main Menu
By default, the system
You must disable Quick Setup in order to access
6
has Quick Setup enabled.
Connect up to eight BNC cameras
to the BNC ports on the rear panel.
Press the MENu/ESC button on the
front panel or the remote control.
the full system main menu.
To disable Quick Setup:
1
1
Quick Setup lets you
quickly adjust the time
and record mode on
the system. The system
menu will appear as the
Quick Setup menu with
only Time and Record
options available.
Retrieve the dVR Information
1. In Quick Setup Menu under the AdVANCEd tab,
select RuN AdVANCEd.
2. Select ON and press the ENTER button. The window
closes. Quick Setup has been disabled. The full main
menu will appear when you press the MENu/ESC
button.
1. dISPLAY
2. CAMERA
3. MOTION
4. RECORd
NOTE: Test the cameras prior to
selecting a permanent mounting
location by temporarily connecting
the Cameras and Cables to your
DVR.
To find the IP and MAC addresses, press the (REWINd) button
on the remote control or
1
1
5
6
7
8
dH200
Series
digimerge Touch dVR
1. Open the MAIN MENu and select SYSTEM.
2. Under the INFO tab, you will find your system’s IP address.
2
5. ALARM
3
4
6. SCHEduLE
7. NETWORK
8. SYSTEM
Connecting the uSB Mouse
QuICK SETuP GuIdE
Managing Passwords
Connect a mouse (USB/PS2
compatible) to the USB port on
By default, you do not have to enter a
password upon initial startup.
However, you can enable this option
in MAIN MENu>SYSTEM>GENERAL.
For more details, please refer to the
2
7
using a Mouse
the rear panel.
1. Left-Button: While in a split-screen display mode,
double-click an individual channel to view it in full-
screen; double-click again to return to the split-
screen display mode. While navigating menus, click
to select a menu option; double-click to open the next
menu.
2
MOuSE TIPS
3
2
PACKAGE CONTENTS:
1 x DIGITAL VIDEO RECORDER WITH PRE-INSTALLED HDD*
1 x POWER ADAPTOR
1 x REMOTE CONTROL
1 x MOUSE
1 x USER MANUAL
1 x QUICK START GUIDE
1 x SOFTWARE CD
user’s manual.
NOTE: This step refers to accessing the MAIN
MENU without enabling the Quick Setup.
1
When using the mouse, the ENTER and
EXIT buttons appear in the top-right corner
of every menu window. When you change
system settings and configurations, click
to confirm your changes.
Setting the date & Time
2. Right-Button: Right-click anywhere on the screen
to open the Virtual Remote; double-click anywhere on
the screen to return to the previous menu.
3. Scroll-Wheel: Move the scroll wheel up or down
to increase/decrease the value of a selected menu
option.
Stop recording (including Manual and
Schedule recording) on the system by
Record the IP and MAC Addresses in the section below:
8
Connecting a Monitor (not included)
pressing/on the front panel, or
pressing the button on the remote
control and enter your 6-digit system
password (by default, 000000).
1. Press the MENu/ESC button to open the
system menu. Select SYSTEM and press
the ENTER button. The System menu
opens.
2. Select the TIME tab.
3. Select dATE and enter the date
(mm/dd/yyyy).
4. Select TIME and enter the time
(hh/mm/ss).
5. Press the ENTER button located at the
top right corner of the screen to save
your changes.
IP ADDRESS :
.
.
.
Connect the VGA cable (not
included) from your LCD monitor
3a
MAC ADDRESS :
:
:
:
:
:
to the VGA port on the rear panel
of the Touch DVR.
Touch Panel Tips and Tricks
(Required for DDNS registration)
If using the Touch panel, you will often use the following
OUT
NOTE: It is highly recommended to set
the time on the system prior to doing any
recording. All recording must be stopped
on the system in order to set the time.
NOTE: If using the mouse right click and
then click on the Virtual Remote.
3
buttons when controlling the system:
• CLR : Menus: move cursor up; Playback: pause playback; Live
OR
viewing: show/hide OSD; clear channel icons
/ : Menus: move cursor down; Playback: stop playback;
Install Software (on your local computer):
ATTENTION:
•
Live viewing: open Log menu
• / : Menus: move cursor left; Playback: increase reverse
playback speed; Live viewing: start/stop recording
IN
Insert the software CD into your
computer’s CD/DVD-R drive. At
From one of the Video-Out ports
3b
• * Channel/ Port configuration and HDD (hard disk drive) capacity may
vary by model. Check your package for specific content information.
• Monitor and Cameras are not included.
2
connect a BNC terminated cable
•
/ : Menus: move cursor right; Playback: increase forward
playback speed; Live viewing: start/stop scheduled recording
the prompt, run or double-click
NetViewInstaller.exe
to a TV or CCTV monitor.
• Ethernet Cable, Broadband Router and Computer are required for
local and remote monitoring (not included).
• For detailed setup and software information, please refer to your
printed User’s manual (included).
• Press the MENu/ESC button to open the main menu and
close windows.
6. Press /on the front panel, or press
the button on the remote control to
resume Continuous Recording.
• Press the
• Press the
button to increase values for selected menu options.
button to decrease values for selected menu options.
OUT
Stopping Scheduled Recording: If you need
to stop a recording schedule, press
on
• Press the button to enter/confirm.
Connecting the Ethernet Cable
the front panel or
on the Remote conrol
NOTE: This step refers to accessing the
MAIN MENU without enabling the Quick
Setup.
1
2
and enter your 6-digit system password (by
default, 000000).
using the Virtual Remote
Connect one end of the Ethernet
4
www.digimerge.com
dVR NetView Software (on your local computer):
It’s all on the Web
cable (not included) (for remote
monitoring) to one of the router’s
(not included) LAN ports and the
other end to the DVR’s Network
Port.
Right-click anywhere on the screen to open the
Virtual Remote. The Virtual Remote gives you
quick acces to many of the system’s features
using only a USB mouse (included).
1. Quick Function Keys
2. Navigation/Menu
3. Playback controls
4. Channel Buttons
4
using the Remote Control
Follow the installation screens to
1
3
Toll free tech support
complete dVR NetView Software
1. LEd Indicator: Flashes red with
2
9
9
available after completing
product registration. For
more information on this
product, firmware updates,
warranty and accessory
products, please visit us at:
every button-press
installation.
10
3
4
2. POWER: Press to power the system
ON/OFF (password required).
3. Navigation/Menu
3
11
12
4
5
Powering ON the Touch dVR
4.
: Press to switch between single
channel full-screen, quad, and
split-screen displays.
Connect the power cable to the
DC port on the rear panel of the
using the Virtual Keyboard
5
6
5.
: Press to confirm menu options/
selections.
When configuring certain options, such as
Camera Title, the Virtual Keyboard opens
to make mouse input easier.
DVR. Touch the POWER button
on the front panel OR press the
POWER button on the remote
control. At startup, the system
performs a basic system check
and runs an initial loading
sequence. After a few moments,
the system loads a live display
view.
7
8
5
6. Playback controls
7. Channel buttons: Press to view
channels 1~8.
Once the installation finishes,
click Close. A shortcut icon
4
NOTE: You will need to input your
system password (by default,
000000) to power off the system.
NOTE: Pressing the “Power”
button after plugging in the power
cable is only necessary for initial
startup (first time out of the box).
appears on your desktop.
Congratulations! You have completed STEP
1 & 2 successfully. Your DVR is now ready to
use. Refer to the owner’s manual to learn
how to record, playback, use the search
features and all other features available
with this DVR.
8.
Press to open the Time Search
menu.
Information in this document is subject to change without notice. As our products are
subject to continuous improvement, Digimerge Technology Inc. reserve the right to
modify product design, specifications and prices, without notice and without incurring
any obligation. E&OE © 2009 Digimerge. All rights reserved.
NOTE: You can use the channel
buttons on the remote control
to enter numbers, letters, and
other characters.
9. CANCEL/ESC: Press to close menu
windows.
10. + increase values.
11. - decrease menu options.
12. Press to start manual recording.
DH200 Touch Series Quick Setup Guide - English - R1
Download from Www.Somanuals.com. All Manuals Search And Download.
|