Desa Water Heater PROPANE GAS LOG HEATER User Manual

SPLIT OAK DESIGN

UNVENTED (VENT-FREE)

PROPANE GAS LOG HEATER

— Also Designed Certified as Vented Decorative Appliance —

This appliance may be installed in an aftermarket* manufactured (mobile) home,

where not prohibited by state or local codes.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

OWNER’S OPERATION AND INSTALLATION MANUAL

PILOT

OFF

24" Variably-Controlled Models

WARNING:Improperinstallation,adjust-

ment,alteration,service,ormaintenance

can cause injury or property damage.

Refer to this manual for correct installa-

tion and operational procedures. For

assistanceoradditionalinformationcon-

sultaqualifiedinstaller,serviceagency,

or the gas supplier.

WARNING: If the information in this

manual is not followed exactly, a fire or

explosion may result causing property

damage, personal injury, or loss of life.

— Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

WARNING: This gas log set is for instal-

lation in a masonry solid fuel burning

fireplace, a U.L. listed manufactured

solid fuel burning fireplace or an AGA

design certified vent-free firebox listed

for use with these gas log models.

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your build-

ing.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

WARNING: This is an unvented gas-

fired heater. It uses air (oxygen) from

the room in which it is installed. Provi-

sionsforadequatecombustionandven-

tilation air must be provided. Refer to

“Air for Combustion and Ventilation”

section in this manual.

• If you cannot reach your gas sup-

plier, call the fire department.

— Installation and service must be per-

formed by a qualified installer, service

agency, or the gas supplier.

Save this manual for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNINGS Continued

WARNING: Any change to this heater or its controls can be dangerous.

1. This appliance is only for use with the type of gas indicated on the rating plate. This

appliance is not convertible for use with other gases.

2. Donotplacepropane(LP)supplytank(s)insideanystructure.Locatepropane(LP)supply

tank(s) outdoors.

SAFETY

INFORMATION

Continued

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use any phone in your building

• immediatelycallyourgassupplierfromaneighbor’sphone. Followthegassupplier’s

instructions

• if you cannot reach your gas supplier, call the fire department

4. This heater shall not be installed in a bedroom or bathroom.

5. Never install the heater

• in a recreational vehicle

• where curtains, furniture, clothing, or other flammable objects are less than 36 inches

from the front, top, or sides of the heater

• in high traffic areas

• in windy or drafty areas

6. Before installing in a solid fuel burning fireplace, the chimney flue and firebox must be

cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner. Creosote

will ignite if highly heated. Inspect chimney flue for damage. If damaged, operate heater

with flue damper closed.

7. Iffireplacehasglassdoors,neveroperatethisheaterwithglassdoorsclosed.Ifyouoperate

heater with doors closed, heat buildup inside fireplace will cause glass to burst. Also if

fireplaceopeninghasventsatthebottom,youmustopentheventsbeforeoperatingheater.

8. You must operate this heater with a fireplace screen in place. Make sure fireplace screen

is closed before running heater.

9. This log heater is designed to be smokeless. If logs ever appear to smoke, turn off heater

and call a qualified service person. Note: During initial operation, slight smoking may

occur due to log curing and heater burning manufacturing residues.

10. Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter burner

flame patterns. Ceiling fans may create drafts that alter burner flame patterns. Altered

burner patterns can cause sooting.

11. Do not use a blower insert, heat exchanger insert or other accessory not approved for use

with this heater.

12. This heater needs fresh, outside air ventilation to run properly. This heater has an oxygen

depletion sensor (ODS) pilot light safety system. The ODS shuts down the heater if not

enough fresh air is available. See Air for Combustion and Ventilation, pages 5 through 8.

If heater keeps shutting off, see Troubleshooting, pages 25 through 28.

13. Do not run heater

• where flammable liquids or vapors are used or stored

• under dusty conditions

14. Do not use this heater to cook food or burn paper or other objects.

15. Never place any objects on the heater.

16. Heater base assembly becomes very hot when running heater. Keep children and adults

awayfromhotsurfacetoavoidburnsorclothingignition. Heaterwillremainhotforatime

after shut-down. Allow surface to cool before touching.

17. Carefully supervise young children when they are in the room with heater.

18. Do not use heater if any part has been exposed to or under water. Immediately call a

qualifiedservicetechniciantoinspecttheroomheaterandtoreplaceanypartofthecontrol

system and any gas control which has been under water.

19. Do not operate heater if any log is broken. Do not operate heater if a log is chipped (dime-

sized or larger).

20. Turn heater off and let cool before servicing. Only a qualified service person should

service and repair heater.

21. Operating heater above elevations of 4,500 feet may cause pilot outage.

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

Crossover Log

PRODUCT

IDENTIFICATION

Rear Log

Top Middle

Log

Front Log

Rear

Burner

Piezo

Ignitor

Front

Bottom

Middle

Log

Burner

Base Assembly

Control Knob

Figure 1 - Vent-Free Gas Log Heater

Install and use heater with care. Follow all local codes. In the absence of local

codes, use the latest edition of The National Fuel Gas Code ANSI Z223, also

known as NFPA 54*.

LOCAL CODES

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

1. Remove logs and heater base assembly from carton. Note: Do not pick up heater

base assembly by burners. This could damage heater. Always handle base

assembly by grate.

UNPACKING

2. Remove all protective packaging applied to logs and heater for shipment.

3. Check all items for any shipping damage. If damaged, promptly inform dealer

where you bought heater.

Operation

PRODUCT

FEATURES

This heater is clean burning. It requires no outside venting. There is no heat loss out a

ventorupachimney.Heatisgeneratedbybothrealisticflamesandglowingcoals.This

heater is designed for vent-free operation with flue damper closed. State and local

codes in some areas prohibit the use of vent-free heaters. You can operate heater as a

vented product by opening flue damper.

Safety Device

This heater has a pilot with an Oxygen Depletion Sensor Shutoff System (ODS).

The ODS/pilot is a required feature for vent-free room heaters. The ODS/pilot shuts

off the heater if there is not enough fresh air.

Piezo Ignition System

This heater has a piezo ignitor. This system requires no matches, batteries, or other

sources to light heater.

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

AIR FOR

COMBUSTION

AND

WARNING

WARNING ICON

001

This heater shall not be installed in a confined space unless

provisions are provided for adequate combustion and ventilation

air. Read the following instructions to insure proper fresh air for

this and other fuel-burning appliances in your home.

VENTILATION

Today’s homes are built more energy efficient than ever. New materials, increased

insulation, and new construction methods help reduce heat loss in homes. Home

owners weather strip and caulk around windows and doors to keep the cold air out

and the warm air in. During heating months, home owners want their homes as

airtight as possible.

While it is good to make your home energy efficient, your home needs to breathe.

Fresh air must enter your home. All fuel-burning appliances need fresh air for

proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances draw air from

the house to operate. You must provide adequate fresh air for these appliances.

This will insure proper venting of vented fuel-burning appliances.

PROVIDING ADEQUATE VENTILATION

The following is exerpts from National Fuel Gas Code. NFPA 54/ANSI Z223.1,

Section 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three following ventilation classifications:

1. Unusually Tight Contruction; 2. Unconfined Space; 3. Confined Space.

The information on pages 5 through 7 will help you classify your space and provide

adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for

combustion and ventilation. However, in buildings of unusually tight construction,

you must provide additional fresh air.

Unusually tight construction is defined as construction where:

a. walls and ceilings exposed to the outside atmosphere have a continu-

ous water vapor retarder with a rating of one perm or less with open-

ings gasketed or sealed and

b. weather stripping has been added on openable windows and doors and

c. caulking or sealants are applied to areas such as joints around window

and door frames, between sole plates and floors, between wall-ceiling

joints, between wall panels, at penetrations for plumbing, electrical, and

gas lines, and at other openings.

If your home meets all of the three criteria above, you must provide addi-

tional fresh air. See Ventilation Air From Outdoors, page 7.

If your home does not meet all of the three criteria above, proceed to page 6.

Unconfined Space

The National Fuel Gas Code, ANSIZ223.1, 1992, Section 5.3 defines uncon-

fined space as having a minimum air volume of 50 cubic feet (127 cubic cm) for

each 1000 Btu/Hr input rating of all appliances in the space (cubic feet equals

length x width x height of space). Include adjoining rooms only if there are

doorless passageways or ventilation grills between the rooms.

Confined Space

The National Fuel Gas Code, ANSIZ223.1, 1992, Section 5.3 defines confined

space as having an air volume of less than 50 cubic feet (127 cubic cm) for each

1000 Btu/Hr input rating of all appliances in the space (cubic feet equals length

x width x height of space). Include adjoining rooms only if there are doorless

passageways or ventilation grills between the rooms.

Continued

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

DETERMINING AIR FLOW FOR HEATER LOCATION

AIR FOR

COMBUSTION

AND

Determining if You Have a Confined or Unconfined Space

Use this work sheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install heater plus any adjoining rooms with

doorless passageways or ventilation grills between the rooms.

VENTILATION

1. Determine the volume of the space (length x width x height).

Continued

Length x Width x Height =

___________________

cu. ft. (volume of space)

Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) =

2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the

volume of these rooms to the total volume of the space.

2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space

can support.

____________ (volume of space) ÷ 50 cu. ft. = (Maximum Btu/Hr

the space can support)

Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. =

51.2 or 51,200 (maximum

Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free heater

Gas water heater*

Gas furnace

Vented gas heater

Gas fireplace logs

Other gas appliances*

Total

___________________ Btu/Hr

+ ___________________ Btu/Hr

= ___________________ Btu/Hr

Example: Gas water heater

Vent-free heater

Total

40,000

33,000

73,000

Btu/Hr

* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the

outdoors and vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr

used.

_________________ Btu/Hr (maximum the space can support)

_________________ Btu/Hr (actual amount of Btu/Hr used)

Example: 51,200 Btu/Hr (maximum the space can support)

73,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/Hr used is more

than the maximum Btu/Hr the space can support. You must provide additional fresh air.

Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the extra space provides

an unconfined space, remove door to adjoining room or add ventilation grills between

rooms. See Ventilation Air From Inside Building, page 7.

B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 7.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space

is an unconfined space. You will need no additional fresh air ventilation.

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

AIR FOR

COMBUSTION

AND

WARNING

If the area in which the heater may be operated is smaller than

that defined as an unconfined space, provide adequate combus-

tion and ventilation air by one of the methods described in the

National Fuel Gas Code, ANSI Z223.1, 1992, Section 5.3.

VENTILATION

Continued

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconfined space. When ventilating to an

adjoining unconfined space, you must provide two permanent openings: one within 12" of the

ceiling and one within 12" of the floor on the wall connecting the two spaces (see options 1 and

2, Figure 2). You can also remove door into adjoining room (see option 3, Figure 2). Follow

the National Fuel Gas Code NFPA 54/ANSI Z223.1, Section 5.3, Air for Combustion and

Ventilation for required size of ventilation grills or ducts.

WARNING

Rework worksheet, adding the space of the adjoining unconfined

space. The combined spaces must have enough fresh air to supply all

appliances in both spaces.

12"

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilation

Grills

into Adjoining

Room,

Option 1

Remove

Door into

Adjoining

Room,

Option 3

12"

Figure 2 - Ventilation Air from Inside Building

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts. You must provide two perma-

nent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these

items directly to the outdoors or spaces open to the outdoors. These spaces include attics

and crawl spaces.

IMPORTANT: Do not provide openings for inlet or outlet air into attic if attic has a thermo-

stat-controlled power vent. Heated air entering the attic will activate the power vent.

Ventilated

Outlet

Attic

Air

Outlet

Air

To Attic

Crawl

Space

Inlet

Air

Ventilated

Inlet Air

Crawl Space

Figure 3 - Ventilation Air from Outdoors

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING

NOTICE

A qualified service person must install heater. Follow all local codes.

NOTICE

State or local codes may only allow operation of this appliance in a

vented configuration. Check your state or local codes.

WARNING

Before installing in a solid fuel burning fireplace, the chimney flue

and firebox must be cleaned of soot, creosote, ashes and loose paint

by a qualified chimney cleaner. Creosote will ignite if highly heated.

Inspect chimney flue for damage. If damaged, operate heater with

flue damper closed.

WARNING

Sealanyfreshairventsorashclean-outdoorslocatedonfloororwall

of fireplace. If not, drafting may cause pilot outage or sooting. Use a

heat-resistant sealant. Do not seal chimney flue damper.

WARNING

Never install the heater

• in a bedroom or bathroom

• in a recreational vehicle

• wherecurtains,furniture,clothing,orotherflammableobjectsare

less than 36 inches from the front, top, or sides of the heater

• in high traffic areas

• in windy or drafty areas

CAUTION

This heater creates warm air currents. These currents move heat

to wall surfaces next to heater. Installing heater next to vinyl or

cloth wall coverings or operating heater where impurities in the air

(such as tobacco smoke) exist, may discolor walls.

IMPORTANT: Vent-free heaters add moisture to the air. Although this is beneficial,

installing heater in rooms without enough ventilation air may cause mildew to form

from too much moisture. See Air for Combustion and Ventilation, pages 5 through 7.

CHECK GAS TYPE

Use only propane gas. If your gas supply is not propane, do not install heater. Call

dealer where you bought heater for proper type heater.

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CLEARANCES (Vent-Free Operation Only)

INSTALLING

Continued

WARNING

Maintain the minimum clearances. If you can, provide greater clear-

ances from floor, ceiling, and adjoining wall.

MINIMUM FIREPLACE CLEARANCE

TO COMBUSTIBLE MATERIALS

Log Size

Side Wall

Ceiling

Floor

24"

16"

42"

LOG SIZING REQUIREMENTS

Log

Size

Minimum Firebox Size

Height

Depth

Front Width

Rear Width

24"

17"

14"

26"

18"

Carefully follow the instructions below. This will ensure safe installation into a

masonry or U.L. listed manufactured fireplace.

Minimum Wall and Ceiling Clearances (see Figure 4)

A. Clearances from the side of the fireplace opening to any combustible wall

should not be less than 16 inches.

B. Clearances from the top of the fireplace opening to the ceiling should not be

less than 42 inches.

42"

16"

Left and

Right Sides

Figure 4 - Minimum Clearance to Wall and Ceiling

Continued

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING

NOTICE

You may use this heater as a vented product. If

so, you must always run heater with chimney flue

damper open. If running heater with damper open,

non-combustible material above fireplace open-

ing is not needed. Go to Installing Damper Clamp

Accessory for Vented Operation, page 13.

Continued

Minimum Non Combustible Material Clearances

If Not Using Mantel

Note: If using a mantel, go to page 11. If not using a mantel, follow the information

on this page.

You must have non combustible material(s) above the fireplace opening. Non

combustible materials (such as slate, marble, tile, etc.) must be at least 1/2 inch

thick. With sheet metal, you must have non combustible material behind it. Non

combustible material must extend at least 8" up. If non combustible material is less

than 12", you must install the fireplace hood accessory. See chart below and Figure

5 for minimum clearances.

IMPORTANT: If you cannot meet these minimum clearances, you must operate

heater with chimney flue damper open. Go to Installing Damper Clamp Accessory

for Vented Operation, page 13.

Non-Combustible

Material Distance (A)

Requirements for

Safe Installation

12" or more

Non combustible material OK.

Between 8" and 12"

Istall fireplace hood acessory (GA6050

or GA6052, see Accessories, page 31).

Less than 8"

Non combustible material must be

extended to at least 8". See Between 8"

and 12", above. If you cannot extend

material, you must operate heater with

flue damper open.

Heat Resistant

Material

(A)

Figure 5 - Heat Resistant Material (Slate, Marble, Tile, etc.) Above Fireplace

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

Minimum Non Combustible Material Clearances

INSTALLING

If Using Mantel

Continued

You must have non combustible material(s) above the fireplace opening. Non

combustible materials (such as slate, marble, tile, etc.) must be at least 1/2 inch

thick. With sheet metal, you must have non combustible material behind it. Non

combustible material must extend at least 8 inches up. If combustible material is

less than 12", you must install the fireplace hood accessory. Even if non combus-

tible material is more than 12", you may need the hood accessory to deflect heat

away from your mantel shelf. See chart below and Figures 6 and 7 for minimum

clearances.

IMPORTANT: If you cannot meet these minimum clearances, you must operate

heater with chimney flue damper open. Go to Installing Damper Clamp Accessory

for Vented Operation, page 13.

Non Combustible

Material Distance (A)

Requirements for

Safe Installation

12" or more

Non combustible material OK.

Between 8" and 12"

Install fireplace hood acessory (GA6050

or GA6052, see Accessories, page 31).

Less than 8"

Non combustible material must be

extended to at least 8". See Between 8"

and 12", above. If you cannot extend

material, you must operate heater with

flue damper open.

Mantel Clearances

If you meet minimum clearance between mantel shelf and top of fireplace opening,

a hood is not required (see Figure 6).

Mantel Shelf

10"

Underside of

Mantel Shelf

2 ^1/2"

All minimum

distances are

in inches

Minimum Non-

Combustible

Material

(A)

Log Set

24"/30" Models

12"

20"

14"

24¹/2"

16³/4"

27¹/2" 30"

18¹/2" 20"

18" Model

Top of Fireplace

Opening

Minimum Non-

Combustible

Material Height

Distances to

Underside of

Mantel

Figure 6 - Minimum Mantel Clearances Without Using Hood

If above minimum clearances are not met, you must have a hood. Follow

minimum clearances shown in Figure 7 when using hood.

Continued

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

Mantel Shelf

12"

10"

INSTALLING

Underside of

Mantel Shelf

Continued

2 ^1/2"

All minimum

distances are

in inches

Minimum Non-

Combustible

Material

Log Sets

12"

15"

18"

20"

18", 24",

Min.

& 30" Models

Top of Fireplace

Opening

Hood

(GA6050, GA6052)

Distances to

Underside of

Mantel

Figure 7 - Minimum Mantel Clearances When Using Hood

If your installation does not meet the above minimum clearances, you must:

• operate the logs only with the flue damper open, OR

• raise the mantel to an acceptable height, OR

• remove the mantel.

Floor Clearances

A. If installing appliance on the floor level, you must maintain the minimum

distance of 14" to combustibles (see Figure 8).

Combustible

Material

14"

Min.

Noncombustible

Material

Figure 8 - Minimum Fireplace Clearances If Installed at Floor Level

B. If combustible materials are less than 14" to the fireplace, you must install

appliance at least 5" above the combustible flooring (see Figure 9).

Hearth

Combustible

Material

Min.

Figure 9 - Minimum Fireplace Clearances Above Combustible Flooring

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING DAMPER CLAMP ACCESSORY FOR

VENTED OPERATION

Note: When used as a vented heater, appliance must be installed only in a solid-

fuel burning fireplace with a working flue and constructed of non combustible

material.

INSTALLING

Continued

If your heater is a manually controlled model, you may use this heater as a vented

product. There are three reasons for operating your heater in the vented mode.

1. The fireplace does not meet the clearance to combustibles requirements for

vent-free operation.

2. State or local codes do not permit vent-free operation.

3. You prefer vented operation.

If reasons number 1 or 2 above apply to you, you must permanently open chimney flue

damper. You must install the damper clamp accessory (to order, see Accessories, page

31). This will insure vented operation (see Figure 10). The damper clamp will keep

damper open. Installation instructions are included with clamp accessory.

See chart below for minimum permanent flue opening you must provide. Attach

damper clamp so the minimum permanent flue opening will be maintained at all times.

Chimney

Height (ft.)

Minimum Permanent

Flue Opening (sq. ins.)

6' to 15'

15' to 30'

39 sq. inches

29 sq. inches

Area of Various Standard Round Flues

Diameter (ins.)

Area (sq. ins.)

20 sq. inches

29 sq. inches

39 sq. inches

51 sq. inches

Damper

Clamp

Damper

Clamp

Damper

Masonry Fireplace

Manufactured Fireplace

Figure 10 - Attaching Damper Clamp

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING HEATER BASE ASSEMBLY

INSTALLING

WARNING

Continued

You must secure this heater to fireplace floor. If not, heater will

move when you adjust controls. Moving heater may cause a gas

leak.

WARNING

If installing in a sunken fireplace, special care is needed. You

must raise the fireplace floor to allow access to heater control

panel. This will insure adequate air flow and guard against soot-

ing. Raise fireplace floor with non-combustible material. Make

sure material is secure.

CAUTION

Do not pick up heater base assembly by burners. This could

damage heater. Only handle base assembly by grates.

IMPORTANT: Make sure the heater burners are level. If heater is not level, heater will

not work properly.

Installation Items Needed

• hardware package (provided with heater)

• approved flexible gas hose (not provided) (if allowed by local codes)

• sealant resistant to propane (LP) gas, not provided

• electric drill with 3/16" drill bit

1. Apply pipe joint sealant lightly to male threads of gas regulator. Connect approved

flexible gas hose to gas regulator of heater (see Figure 11).

IMPORTANT: Hold gas regulator with wrench when connecting flexible gas hose.

2. Locate mounting brackets, bolts, and nuts in hardware package. Attach mounting

brackets to heater base (see Figure 12). Attach nuts finger tight.

3. Position heater base assembly in fireplace.

4. Mark screw locations through holes in mounting brackets. If installing in a brick-

bottom fireplace, mark screw locations in mortar joint of bricks.

5. Remove heater base from fireplace. Remove mounting brackets from heater base.

6. Drill holes at marked locations using 3/16" drill bit.

7. Attachmountingbracketstofireplacefloorusingmasonryscrews(inhardwarepackage).

8. Reattach heater base to mounting brackets. Tighten nuts firmly.

9. Connect to gas supply. See Connecting To Gas Supply, page 15.

Heater Gas

Regulator

Flexible Gas Hose (if

allowed by local codes)

Figure 11 - Attaching Flexible Gas Hose to Heater Gas Regulator

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING

Continued

Masonry Screw

Mounting

Bracket

Figure 12 - Attaching Mounting Brackets to Heater

CONNECTING TO GAS SUPPLY

NOTICE

A qualified service person must connect heater to gas supply.

Follow all local codes.

CAUTION

Never connect heater directly to the propane supply. This heater

requires an external regulator (not supplied). Install the external

regulator between the heater and propane supply.

Installation Items Needed

Before installing heater, make sure you have the items listed below.

• external regulator (supplied by

installer, see page 16)

• piping (check local codes)

• sealant (resistant to LP gas)

• manual shutoff valve *

• test gauge connection *

• sediment trap

• tee joint

• pipe wrench

* An A.G.A. design-certified manual shutoff valve with 1/8" NPT tap is an acceptable

alternative to test gauge connection. Purchase the optional A.G.A. design-certified manual

shutoff valve from your dealer. See Accessories, page 31.

Continued

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

The installer must supply an external regulator. The external regulator will reduce

incoming gas pressure. You must reduce incoming gas pressure to between 11 and

14 inches of water. If you do not reduce incoming gas pressure, heater regulator

damage could occur. Install external regulator with the vent pointing down as

shown in Figure 13. Pointing the vent down protects it from freezing rain or sleet.

INSTALLING

Continued

Propane

Supply Tank

External

Regulator

Vent Pointing

Down

Figure 13 - External Regulator With Vent Pointing Down

CAUTION

Use only new, black iron or steel pipe. Internally-tinned copper

tubing may be used in certain areas. Check your local codes. Use

pipe of 1/2" diameter or greater to allow proper gas volume to

heater. If pipe is too small, undue loss of pressure will occur.

Installation must include a manual shutoff valve, union, and plugged 1/8" NPT tap.

Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream

from heater (see Figure 14, page 17).

Apply pipe joint sealant lightly to male threads. This will prevent excess sealant

from going into pipe. Excess sealant in pipe could result in clogged heater valves.

CAUTION

Use pipe joint sealant that is resistant to liquid petroleum (LP) gas.

Install sediment trap in supply line as shown in Figure 14, page 17. Locate sedi-

ment trap where it is within reach for cleaning. Locate sediment trap where trapped

matter is not likely to freeze. A sediment trap traps moisture and contaminants. This

keeps them from going into heater controls. If sediment trap is not installed or is

installed wrong, heater may not run properly.

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING

CAUTION

Avoid damage to regulator. Hold gas regulator with wrench when

connecting it to gas piping and/or fittings.

Continued

A.G.A. Design-Certified

Manual Shutoff Valve

With 1/8" NPT Tap*

From

External Regulator

(11" W.C.** to

14" W.C.

Approved Flexible

Gas Hose (if allowed

by local codes)

Pressure)

Gas

Regulator

Tee Joint

Pipe

Nipple

3" Minimum

Cap

Sediment

Trap

Figure 14 - Gas Connection

*PurchasetheoptionalA.G.A.design-certifiedmanualshutoffvalvefromyourdealer.

See Accessories, page 31.

** Minimum inlet pressure for purpose of input adjustment.

CHECKING GAS CONNECTIONS

WARNING

Test all gas piping and connections for leaks after installing or

servicing. Correct all leaks at once.

WARNING

Never use an open flame to check for a leak. Apply a mixture of

liquid soap and water to all joints. Bubbles forming show a leak.

Correct all leaks at once.

CAUTION

Make sure external regulator has been installed between propane

supply and heater. See guidelines under Connecting to Gas Sup-

ply, page 15.

Pressure Testing gas Supply Piping system

Test Pressures In Excess Of 1/2 PSIG

1. Disconnect heater and its individual manual shutoff valve from gas supply

piping system. Pressures in excess of 1/2 psig will damage heater regulator.

2. Cap off open end of gas pipe where manual shutoff valve was connected.

Continued

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Pressurize supply piping system by either using compressed air or

opening propane supply tank valve.

4. Check all joints of gas supply piping system. Apply mixture of liquid soap and water to

gas joints. Bubbles forming show a leak.

INSTALLING

Continued

5. Correct all leaks at once.

6. Re-connect heater and manual shutoff valve to gas supply. Check re-connected fittings

for leaks.

Test Pressures Equal To or Less Than 1/2 PSIG

1. Close manual shutoff valve (see Figure 15).

2. Pressurize supply piping system by either using compressed air or opening propane

supply tank valve.

3. Check all joints from propane supply tank to manual shutoff valve (see Figure 16).

Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak.

4. Correct all leaks at once.

Pressure Testing Heater Gas Connections

1. Open manual shutoff valve (see Figure 15).

2. Open propane supply tank valve.

3. Make sure control knob of heater is in the OFF position.

4. Check all joints from manual shutoff valve to control valve (see Figure 16). Apply

mixture of liquid soap and water to gas joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Light heater (see Operating Heater, pages 22 through 23). Check all other internal

joints for leaks.

7. Turn off heater (see To Turn Off Gas to Appliance, page 23).

OSI

TIO

^ONe

Manual

Shutoff

Valve

OFF

POSITION

Closed

Figure 15 - Manual Shutoff Valve

Manual

Shutoff

Valve

Control Valve Location

Propane

Supply Tank

Figure 16 - Checking Gas Joints

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING LOGS

INSTALLING

Continued

WARNING

Failure to position the parts in accordance with these diagrams or

failure to use only parts specifically approved with this heater may

result in property damage or personal injury.

Each log is marked with a number. These numbers will help you identify the log when

installing. It is very important to install these logs exactly as instructed. Do not modify logs.

Only use logs supplied with heater.

1. Place front logs (#1L and #1R) on top of the grate. Make sure the notches in the bottom

of the logs fit over the grate prongs (see Figure 17). Push back of logs flush with metal

grate bar.

Front Log (#1L)

Notch

Front Log (#1R)

Grate Prongs

Metal Grate Bar

Figure 17 - Installing Front Logs (#1L and #1R)

2. Rest bottom middle log (#2) behind metal posts on front burner. Make sure the grooves in

the bottom of the log fit over the grate. Bring the log forward next to the metal posts. The

pegs on the log must be on top (see Figure 18).

Peg

Bottom Middle Log (#2)

Peg

Groove

Metal Post

Groove

Metal Post

Grate

Figure 18 - Installing Bottom Middle Log (#2)

Continued

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Slide the grooves in the back of the rear log (#3) against the rear grate prongs. Make sure

the peg on the log is on top (see Figure 19).

INSTALLING

Continued

Peg

Groove in

Back of Log

Rear Log (#3)

Grate Prong

Groove in

Back of Log

Rear Burner

Grate Prong

Figure 19 - Installing Rear Log (#3)

4. Place the top middle log (#4) on the bottom middle log (#2). Make sure the pegs of the

bottom middle log fit securely in the holes of the top middle log (see Figure 20).

Top Middle Log (#4)

Hole

Peg

Bottom

Middle Log

Figure 20 - Installing Top Log (#4)

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Place the crossover log (#5) on the back log and the top middle log. Make sure the peg

on the rear log is in the hole in the bottom of the crossover log. The crossover log should

fit in the cutout of the top middle log (see Figure 21).

INSTALLING

Continued

Crossover

Log (#4)

Hole

Cutout

Peg

Figure 21 - Installing Crossover Log (#5)

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

FOR YOUR SAFETY READ BEFORE LIGHTING

OPERATING

HEATER

WARNING

If you do not follow these instructions exactly, a fire or explosion

may result causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand. When lighting the pilot,

follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell

next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

C. Useonlyyourhandtopushinorturnthegascontrolknob. Neverusetools. Iftheknob

will not push in or turn by hand, don’t try to repair it, call a qualified service

technician or gas supplier. Force or attempted repair may result in a fire or explosion.

D. Do not use this appliance if any part has been under water. Immediately call a

qualified service technician to inspect the appliance and to replace any part of the

control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS

WARNING

• If fireplace has glass doors, never operate this heater with glass doors

closed. If you operate heater with doors closed, heat buildup inside

fireplacewillcauseglasstoburst. Alsoiffireplaceopeninghasventsatthe

bottom, you must open the vents before operating heater.

• You must operate this heater with a fireplace screen in place. Make sure

fireplace screen is closed before running heater.

NOTICE

During initial operation of new heater, burning logs will give off a paper-

burning smell. Orange flame will also be present. Open damper or window

to vent smell. This will only last a few hours.

Note: Homeowners generally prefer to operate their heater with the chimney damper

closed. This will put all the heat into the room. However there may be times you will

desire the full flames of the Hi heat setting but will find the heat output excessive. You

can open the chimney damper (if you have one) fully or partially to release some of the

heat. WARNING: Damper handle will be hot if heater has been running.

1. STOP! Read the safety information above.

2. Make sure manual shutoff valve is fully open.

Clockwise

3. Turn control knob clockwise

to the OFF position.

Control Knob

Ignitor Button

PILOT

OFF

Figure 22 - Control Knob and Ignitor Button Location

4. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the

floor. If you smell gas, STOP! Follow “B” in the safety information above. If you

don’t smell gas, go to the next step.

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

C-clockwise

5. Turn control knob counterclockwise

to the PILOT position. Press in

OPERATING

control knob for five (5) seconds (see Page 22).

Note: You may be running this heater for the first time after hooking up to gas

supply. If so, the control knob may need to be pressed in for 30 seconds or less.

This will allow air to bleed from the gas system.

HEATER

Continued

• If control knob does not pop out when released, contact a qualified service

person or gas supplier for repairs.

6. With control knob pressed in, press and release ignitor button. This will light pilot.

The pilot is attached to the front burner. If needed, keep pressing ignitor button

until pilot lights.

Note: If pilot does not stay lit, contact a qualified service person or gas supplier

for repairs. Until repairs are made, light pilot with match. To light pilot with

match, see Manual Lighting Procedure, below.

7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds,

release control knob.

Note: If pilot goes out, repeat steps 3 through 7. This heater has a safety inter-

lock system. Wait one (1) minute for system to reset before lighting pilot again.

Ignitor Electrode

Pilot Burner

Thermocouple

Figure 23 - Pilot

8. Turn control knob counterclockwise

to desired heating level. The burners

C-clockwise

should light. Set control knob to any heat level between HI and LO.

CAUTION

Do not try to adjust heating levels by using the manual shutoff valve.

TO TURN OFF GAS TO APPLIANCE

Shutting Off Heater

1. Turn control knob clockwise

Shutting Off Burners Only (pilot stays lit)

1. Turn control knob clockwise to the PILOT position.

to the OFF position.

Clockwise

VARIABLE CONTROL OPERATION

The variable control valve can be set to any heat setting and flame height desired, by

simply turning the control knob until that setting is attained. Even the lowest setting

provides realistic flames and glowing embers from two burners. Selecting higher

settings produces greater heat output. This results in increased heating comfort.

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

Check pilot flame pattern and burner flame patterns often.

INSPECTING

BURNERS

PILOT FLAME PATTERN

Figure 24 shows a correct pilot flame pattern. Figure 25 shows an incorrect pilot flame

pattern. The incorrect pilot flame is not touching the thermocouple. This will cause the

thermocouple to cool. When the thermocouple cools, the heater will shut down.

Thermocouple

Pilot Burner

Figure 24 - Correct Pilot

Flame Pattern

Figure 25 - Incorrect Pilot

Flame Pattern

If pilot flame pattern is incorrect, as shown in Figure 25

• turn heater off (see To Turn Off Gas to Appliance, page 23)

• see Troubleshooting, pages 25 through 28

FRONT BURNER FLAME PATTERN

Figure 26 shows correct front burner flame pattern. Figure 27 shows incorrect front

burner flame pattern. The incorrect burner flame pattern shows yellow tipping at top of

blue flame.

WARNING

If yellow tipping occurs, your heater could produce increased levels

of carbon monoxide. If front burner flame pattern shows yellow

tipping,followinstructionsatbottomofthispage.Yellowflameonrear

burner is normal.

NOTICE

Do not mistake orange flames with yellow tipping. Dirt or other fine

particles are burned by heater, causing brief patches of orange flame.

CORRECT FLAME PATTERN AT HIGH POSITION

Figure 26 - Correct Front Burner Flame Pattern

Yellow

Tipping

At Top

of Blue

Flame

INCORRECT FLAME PATTERN AT HIGH POSITION

Figure 27 - Incorrect Front Burner Flame Pattern

If front burner flame pattern is incorrect, as shown in Figure 27

• turn heater off (see To Turn Off Gas to Appliance, page 23)

• see Troubleshooting, pages 25 through 28

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

CLEANING

AND

WARNING

Turn off heater and let cool before cleaning.

MAINTENANCE

CAUTION

You must keep control areas, burners, and circulating air passage-

ways of heater clean. Inspect these areas of heater before each

use. Have heater inspected yearly by a qualified service person.

Heater may need more frequent cleaning due to excessive lint from

carpeting, bedding material, etc.

ODS/PILOT AND BURNERS

• Use a vacuum cleaner or small, soft bristled brush to clean.

LOGS

• If you remove logs for cleaning, refer to Installing Logs, page 19, to properly

replace logs.

• Replace log(s) if broken or chipped (dime-sized or larger).

TROUBLE-

SHOOTING

WARNING

Turn off and unplug heater and let cool before servicing. Only a

qualified service person should service and repair heater.

Note: All trouble-

shooting items are

listed in order of

operation.

CAUTION

Never use a wire, needle, or similar object to clean ODS/pilot. This

can damage ODS/pilot unit.

OBSERVED

PROBLEM

POSSIBLE

CAUSE

REMEDY

When ignitor button

is pressed, there is no

spark at ODS/pilot

1. Ignitor electrode not con- 1. Reconnect ignitor cable

nected to ignitor cable

2. Ignitor cable pinched or

wet

2. Free ignitor cable if

pinched by any metal or

tubing. Keep ignitor

cable dry

3. Piezo ignitor nut is loose 3. Tighten nut holding

piezo ignitor to base

panel of log set. Nut is

located behind base

panel.

4. Broken ignitor cable

5. Bad piezo ignitor

6. Ignitor electrode broken

7. Ignitor electrode posi-

tioned wrong

4. Replace ignitor cable

5. Replace piezo ignitor

6. Replace piezo ignitor

7. Replace piezo ignitor

Continued

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

OBSERVED

PROBLEM

POSSIBLE

CAUSE

TROUBLE-

REMEDY

SHOOTING

When ignitor button

is pressed, there is

spark at ODS/pilot

but no ignition

1. Gas supply turned off or 1. Turn on gas supply or

Continued

manual shutoff valve

closed

open manual shutoff

valve

2. Control knob not in

PILOT position

2. Turn control knob to

PILOT position

3. Control knob not

pressed in while in

PILOT position

3. Press in control knob

while in PILOT position

4. Air in gas lines when

installed

4. Continue holding down

control knob. Repeat

igniting operation until

air is removed

5. Depleted gas supply

6. ODS/pilot is clogged

5. Contact local propane

gas company

6. Clean ODS/pilot (see

Cleaning and Mainte-

nance, page 25) or

replace ODS/pilot

assembly

7. Gas regulator setting is

not correct

7. Replace gas regulator

ODS/pilot lights but

flame goes out when

control knob is

released

1. Control knob not fully

pressed in

2. Control knob not

pressed in long enough

1. Press in control knob

fully

2. After ODS/pilot lights,

keep control knob

pressed in 30 seconds

3. Fully open manual shut-

off valve

3. Manual shutoff valve

not fully open

4. Pilot flame not touching

thermocouple, which

allows thermocouple to

cool, causing pilot flame

to go out. This problem

could be caused by one

or both of the following:

A) Low gas pressure

B) Dirty or partially

clogged ODS/pilot

4. A) Contact local propane

gas company

B) Clean ODS/pilot (see

Cleaning and Mainte-

nance, page 25) or

replace ODS/pilot

assembly

5. Thermocouple connec-

tion loose at control

valve

5. Hand tighten until snug,

then tighten 1/4 turn

6. Thermocouple damaged 6. Replace thermocouple

7. Control valve damaged 7. Replace control valve

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

OBSERVED

PROBLEM

POSSIBLE

CAUSE

TROUBLE-

REMEDY

SHOOTING

One or both burners

do not light after

ODS/pilot is lit

1. Burner orifice(s)

clogged

1. Clean burner(s) (see

Cleaning and Mainte-

nance, page 25) or

Continued

replace burner orifice(s)

2. Contact local propane

gas company

3. Contact qualified service

person

2. Inlet gas pressure is

too low

3. Mislocated crossover

tube

4. Burner orifice(s)

diameter is too small

4. Replace burner orifice(s)

Delayed ignition of

one or both burners

1. Manifold pressure is

too low

2. Burner orifice(s)

clogged

1. Contact local propane

gas company

2. Clean burner(s) (see

Cleaning and Mainte-

nance, page 25) or

replace burner orifice(s)

3. Contact qualified service

person

3. Mislocated crossover

tube

Burner backfiring

during combustion

1. Burner orifice is

clogged or damaged

1. Clean burner (see

Cleaning and Mainte-

nance, page 25) or

replace burner orifice

2. Replace damaged burner

3. Replace gas regulator

2. Damaged burner

3. Gas regulator defective

Yellow flame in front

burner during burner

combustion

1. Not enough air

1. Check burner(s) for dirt

and debris. If found,

clean burner(s) (see

Cleaning and Mainte-

nance, page 25)

2. Gas regulator defective

2. Replace gas regulator

Slight smoke or odor

during initial opera-

tion

1. Residues from manu-

facturing processes

and logs curing

1. Problem will stop after a

few hours of operation

Moisture/condensation 1. Not enough combus-

1. Refer to Air for Com-

bustion and Ventilation

requirements (page 5)

noticed on windows

tion/ventilation air

Heater produces a

whistling noise when

burners are lit

1. Turning control knob

to HI position when

burners are cold

1. Turn control knob to LO

position and let warm up

for a minute

2. Operate burners until air

is removed from line.

Have gas line checked

by local propane gas

company

2. Air in gas line

3. Air passageways on

heater blocked

3. Observe minimum

installation clearances

(see pages 9-12)

4. Dirty or partially

clogged burner

orifice(s)

4. Clean burners (see

Cleaning and Maintenance,

page 25) or replace

burner orifice(s)

Continued

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLE-

WARNING

If you smell gas

SHOOTING

• Shut off gas supply.

Continued

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the fire department.

IMPORTANT: Operating heater where impurities in air exist may create odors.

Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new

carpet or textiles, etc., create fumes. These fumes may mix with combustion air and

create odors. These odors will disappear over time.

OBSERVED

PROBLEM

POSSIBLE

CAUSE

REMEDY

Heater produces a

clicking/ticking noise

just after burners are lit

or shut off

1. This is common with

most heaters. If noise is

excessive, contact

1. Metal expanding while

heating or contracting

while cooling

qualified service person

Heater produces

unwanted odors

1. Open window to ventilate

room. Stop using odor

causing products while

heater is running

1. Heater burning vapors

from paint, hair spray,

glues, cleaners, chemi-

cals, new carpet, etc.

(See IMPORTANT

statement above)

2. Refill supply tank

2. Low fuel supply

3. Gas leak. See Warning

statement at top of

page

3. Locate and correct all leaks

(see Checking Gas Con-

nections, page 17)

Heater shuts off in use

(ODS operates)

1. Open window and/or door

for ventilation

1. Not enough fresh air is

available

2. Contact local propane gas

company

2. Low line pressure

3. Clean ODS/pilot (see

Cleaning and Mainte-

nance, page 25)

3. ODS/pilot is partially

clogged

Gas odor even when

control knob is in OFF

position

1. Locate and correct all leaks

(see Checking Gas Con-

nections, page 17)

1. Gas leak. See Warning

statement at top of

page

2. Replace control valve

2. Control valve defective

Gas odor during

combustion

1. Take apart gas tubing and

remove foreign matter

2. Locate and correct all leaks

(see Checking Gas Con-

nections, page 17)

1. Foreign matter between

control valve and burner

2. Gas leak. See Warning

statement at top of

page

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

You may have further questions about installation, operation, or troubleshooting.

If so, contact DESA International’s Technical Service Department at

1-800-DESA LOG (1-800-337-2564).

TECHNICAL

SERVICE

24" MODEL

SPECIFICATIONS

Btu (Variable)

Type Gas

20,000/33,000

Propane Only

Piezo

Ignition

Manifold Pressure

7.9" W.C.

Inlet Gas

Pressure (in. of water)

Maximum

14"

11"

Minimum*

Shipping Weight

38 lbs.

* For the purpose of input adjustment

When gas pressure is too low

• pilot will not stay lit

SERVICE

HINTS

• burners will have delayed ignition

• heater will not produce specified heat

• propane gas supply may be low

When gas quality is bad

• pilot will not stay lit

• burners will produce flames and soot

• heater will backfire when lit

You may feel your gas pressure is too low or gas quality is bad. If so, contact your

local propane gas supplier.

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

Note: Use only original replacement parts. This will protect your warranty cover-

age for parts replaced under warranty.

REPLACEMENT

PARTS

Parts Under Warranty

Contact authorized dealers of this product. If they can’t supply original replacement

part(s), call DESA International’s Technical Service Department at

1-800-DESA LOG (1-800-337-2564).

When calling DESA International, have ready

• your name

• your address

• model number of your heater

• how heater was malfunctioning

• type of gas used (propane or natural gas)

• purchase date

Usually, we will ask you to return the defective part to the factory.

Parts Not Under Warranty

Contact authorized dealers of this product. If they can’t supply original replacement

part(s), call DESA International’s Parts Department at 1-800-972-7879 for information.

When calling DESA International, have ready

• model number of your heater

• the replacement part number

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

Purchase these fireplace accessories from your local dealer. If they can not supply

these accessories, call DESA International’s Sales Department at 1-800-432-2382

for information. You can also write to the address listed on the back page of this

manual.

ACCESSORIES

MANUAL SHUTOFF

VALVE - GA5010

For all models. Manual shutoff valve

with 1/8" NPT tap. Fits 1/2" NPT

pipe.

BLACK FIREPLACE

HOOD - GA6050

For all models. Helps

deflect heat away from

mantel or wall above

fireplace.

BRASS FIREPLACE

HOOD - GA6052

For all models. Helps

deflect heat away from

mantel or wall above

fireplace.

DAMPER CLAMP - GA6080

For variably controlled models.

Permanently opens chimney flue

damper for vented operation.

LAVA ROCK - GA6060

For all models. Order when additional

rock is desired. (3 lb. bag)

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

ILLUSTRATED

PARTS

BREAKDOWN

28-1

28-2

7-2

7-1

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

This list contains replaceable parts used in your heater. When ordering parts, follow

the instructions listed under Replacement Parts on page 30 of this manual.

PARTS LIST

KEY

NO.

PART NUMBER

DESCRIPTION

QTY.

102474-01

102474-02

102475-01

102478-01

102477-01

102479-01

101006-01

101330-05

101008-01

101007-01

100999-02

101331-08

098271-06

102445-01

098867-08

M11084-38

100996-02

098354-01

102013-01

100000-01

101053-01

099211-01

101329-10

100994-01

101004-01

101004-02

101012-01

099387-09

102255-01

M11084-26

099059-02

Left Front Log (#1)

Right Front Log (#1R)

Bottom Middle Log (#2)

Rear Log (#3)

Top Middle Log (#4)

Crossover Log (#5)

Pilot Bracket

Front Burner Assembly

Gasket, Crossover Burner

Crossover Burner

Rear Burner Assembly

Base Assembly (with decals)

Ignitor Cable

Piezo Ignitor

Gas Regulator

Screw

Pipe Nipple

Control Knob

Control Rod

Cotter Pin

Adapter

Screw

Gas Valve Assembly

Valve Bracket

Rear Burner Injector

Front Burner Injector

Burner Tube

Pilot Tube

Strap

Screw

O.D.S. Pilot

7-1

7-2

28-1 098594-01

28-2 098593-01

Ignitor Electrode

Thermocouple

Nut

098249-01

102764-01

Heat Shield

PARTS AVAILABLE — NOT SHOWN

100563-01

Warning Plate

Lighting Instructions Plate

Chain

Caution Decal

Hardware Kit

101054-01

100565-01

100639-01

101137-01

101416-10

GA6060

Information Video

Lava Rock

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

________________________________________________________________

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

________________________________________________________________

102318

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY INFORMATION

KEEP THIS WARRANTY

Model

Serial No.

Date Purchased

Always specify model and serial numbers when communicating with the factory.

We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard

written warranty. We make no other warranty, expressed or implied.

LIMITED WARRANTY

VENT-FREE PROPANE GAS LOG HEATERS

DESA International warrants this product to be free from defects in materials and components for three (3) years and five

(5) years on stainless steel burners from the date of first purchase, provided that the product has been properly installed,

operated and maintained in accordance with all applicable instructions. To make a claim under this warranty the Bill of Sale

or cancelled check must be presented.

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this

heater to proper operating condition and an allowance for labor when provided by a DESA Authorized Service Center.

Warranty part(s) MUST be obtained through authorized dealers of this product and/or DESA International who will provide

original factory replacement parts. Failure to use original factory replacement parts voids this warranty. The heater MUST

be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or

become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation.

Travel, diagnostic cost, labor, transportation and any and all such other costs related to repairing a defective heater will be

the responsibility of the owner.

TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE

PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND

LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO THREE (3) YEARS ON ALL COMPONENTS

AND FIVE (5) YEARS ON STAINLESS STEEL BURNERS FROM THE DATE OF FIRST PURCHASE; AND DESA

INTERNATIONAL’SLIABILITYISHEREBYLIMITEDTOTHEPURCHASEPRICEOFTHEPRODUCTANDDESA

INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDI-

RECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or

consequential damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply

to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

For information about this warranty write:

INTERNATIONAL

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

102318-01

Rev. D

12/95

Download from Www.Somanuals.com. All Manuals Search And Download.

Coleman Tent 2000004408 User Manual
Conair Electric Shaver GMT170ECS User Manual
Contec Universal Remote RT U50 25S User Manual
Cooper Lighting Indoor Furnishings 23ADIW User Manual
Creative Headphones HQ 2300D User Manual
Curtis Mathes CRT Television CM 13102 User Manual
Delta Electronics Power Supply HMU1356S User Manual
Faber Ventilation Hood INCA SMART User Manual
FujiFilm Digital Camera 40i User Manual
Fundex Games Games Timber Tumble User Manual