Desa Stove S26NT User Manual

VENT-FREE NATURAL GAS

FREESTANDING PEDESTAL STOVE SYSTEM

OWNER’S OPERATION AND INSTALLATION MANUAL

S26NT

20,000 to 26,000 Btu/Hr

Thermostatically-

Controlled

WARNING: Improper installa-

tion,adjustment,alteration,ser-

vice,ormaintenancecancause

injury or property damage. Re-

WARNING: If the information in this manual is not

followed exactly, a fire or explosion may result caus-

ing property damage, personal injury, or loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

fer to this manual for correct

installationandoperationalpro-

cedures. For assistance or ad-

ditional information consult a

qualified installer, service

agency, or the gas supplier.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

fire department.

WARNING: This is an unvented

gas-fired heater. It uses air (oxy-

gen) from the room in which it is

installed.Provisionsforadequate

combustion and ventilation air

must be provided. Refer to Air for

Combustion and Ventilation sec-

tion on page 4 of this manual.

— Installation and service must be performed

by a qualified installer, service agency, or the

gas supplier.

This appliance may be installed in an aftermarket*, permanently located, manu-

factured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate.

This appliance is not convertible for use with other gases.

*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

Save this manual for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

PRODUCT

IDENTIFICATION

PRODUCT

FEATURES

SAFETY PILOT

ThisheaterhasapilotwithanOxygenDeple-

tion Sensing (ODS) safety shutoff system.

The ODS/pilot is a required feature for vent-

free room heaters. The ODS/pilot shuts off

the heater if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This heater has a piezo ignitor. This system

requires no matches, batteries, or other

sources to light heater.

Stove

Cabinet

Screen

Logs

Heater Controls

(Inside Door)

Figure 1 - Vent-Free Natural Gas Stove

LOCAL CODES

UNPACKING

Install and use heater with care. Follow all

local codes. In the absence of local codes, use

the latest edition of The National Fuel Gas

Code, ANSZ223.1,alsoknownasNFPA54*.

1. Remove top inner pack.

2. Tilt carton so that stove is upright.

3. Remove protective side packaging.

4. Slide stove out of carton.

*Available from:

5. Remove protective plastic wrap.

American National Standards Institute, Inc.

1430 Broadway

6. Remove screen by lifting and then pull-

ing forward.

New York, NY 10018

7. Remove log set by cutting plastic ties.

8. Carefully unwrap log.

National Fire Protection Association, Inc.

Batterymarch Park

9. Check for any shipping damage. If

stove or log is damaged, promptly in-

form dealer where you bought stove.

Quincy, MA 02269

This heater is designed for vent-free opera-

tion. State and local codes in some areas

prohibit the use of vent-free heaters.

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE NATURAL GAS PEDESTAL STOVE

Confined and Unconfined Space

PROVIDING ADEQUATE

VENTILATION

AIR FOR

The National Fuel Gas Code, ANS Z223.1

defines a confined space as a space whose

volume is less than 50 cubic feet per 1,000

Btu per hour (4.8 m³per kw) of the aggre-

gate input rating of all appliances installed

in that space and an unconfining space as a

space whose volume is not less than 50

cubicfeetper1,000Btuperhour(4.8m³per

kw) of the aggregate input rating of all

appliances installed in that space. Rooms

communicating directly with the space in

whichtheappliancesareinstalled*,through

openings not furnished with doors, are con-

sidered a part of the unconfined space.

COMBUSTION AND

VENTILATION

The following are excerpts from National

Fuel Gas Code, NFPA 54/ANS Z223.1, Sec-

tion5.3, AirforCombustionandVentilation.

WARNING: This heater shall

notbeinstalledinaconfinedspace

or unusually tight construction

unless provisions are provided

foradequatecombustionandven-

tilation air. Read the following in-

structions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

All spaces in homes fall into one of the three

following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 4 through 6 will

help you classify your space and provide

adequate ventilation.

This heater shall not be installed in a con-

fined space or unusually tight construction

unless provisions are provided for adequate

combustion and ventilation air.

Today’s homes are built more energy effi-

cient than ever. New materials, increased

insulation, and new construction methods

help reduce heat loss in homes. Home

owners weather strip and caulk around

windows and doors to keep the cold air out

andthewarmairin.Duringheatingmonths,

home owners want their homes as airtight

as possible.

Unusually Tight Construction

The air that leaks around doors and win-

dows may provide enough fresh air for

combustion and ventilation. However, in

buildings of unusually tight construction,

you must provide additional fresh air.

*Adjoiningroomsarecommunicatingonly

iftherearedoorlesspassagewaysorventila-

tion grills between them.

Unusually tight construction is de-

fined as construction where:

a. walls and ceilings exposed to the

outside atmosphere have a con-

tinuous water vapor retarder with

a rating of one perm (6 x 10^-11kg

per pa-sec-m²) or less with open-

ings gasketed or sealed and

While it is good to make your home energy

efficient,yourhomeneedstobreathe.Fresh

air must enter your home. All fuel-burning

appliances need fresh air for proper com-

bustion and ventilation.

Exhaust fans, heaters, clothes dryers, and

fuel burning appliances draw air from the

house to operate. You must provide ad-

equate fresh air for these appliances. This

will insure proper venting of vented fuel-

burning appliances.

b. weather stripping has been

added on openable windows and

doors and

c. caulking or sealants are applied

to areas such as joints around

window and door frames, be-

tween sole plates and floors, be-

tween wall-ceiling joints, be-

tween wall panels, at penetra-

tions for plumbing, electrical, and

gas lines, and at other openings.

If your home meets all of the three

criteria above, you must provide ad-

ditional fresh air. See Ventilation Air

From Outdoors, page 6.

If your home does not meet all of the

three criteria above, proceed to Deter-

mining Fresh-Air Flow For Heater

Location, page 5.

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

AIR FOR

COMBUSTION AND

VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Confined or Unconfined Space

Use this worksheet to determine if you have a confined or unconfined space.

Space:Includestheroominwhichyouwillinstallheaterplusanyadjoiningroomswithdoorlesspassagewaysorventilationgrillsbetween

the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height = ____________________ cu. ft. (volume of space)

Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of

the space.

2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.

_________________ (volume of space) ÷ 50 cu. ft. = (Maximum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free heater

Gas water heater*

Gas furnace

_________________Btu/Hr

Example:

Gas water heater

30,000

26,000

56,000

Btu/Hr

Vent-free heater +

Vented gas heater

Gas heater logs

Total

Other gas appliances* +

Total

* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_________________ Btu/Hr (maximum the space can support)

_________________ Btu/Hr (actual amount of Btu/Hr used)

Example: 51,200 Btu/Hr (maximum the space can support)

56,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support.

You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoining

room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.

B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no

additional fresh air ventilation.

WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space

or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of

the methods described in the National Fuel Gas Code, ANS Z223.1, Section 5.3 or applicable local codes.

Continued

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE NATURAL GAS PEDESTAL STOVE

AIR FOR

12"

COMBUSTION AND

VENTILATION

Ventilation

Grills

Into Adjoining

Room,

Option 1

Ventilation Grills

Into Adjoining Room,

Option 2

Continued

VENTILATION AIR

Remove

Door into

Adjoining

Room,

Option

Ventilation Air From Inside

Building

Thisfreshairwouldcomefromanadjoining

unconfined space. When ventilating to an

adjoining unconfined space, you must pro-

vide two permanent openings: one within

12" of the ceiling and one within 12" of the

floor on the wall connecting the two spaces

(see options 1 and 2, Figure 2). You can also

remove door into adjoining room (see op-

tion 3, Figure 2). Follow the National Fuel

Gas Code, NFPA 54/ANS Z223.1, Section

5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

12"

Figure 2 - Ventilation Air from Inside Building

WARNING: Rework work-

sheet, adding the space of the

adjoining unconfined space. The

combined spaces must have

enough fresh air to supply all

appliances in both spaces.

Ventilated

Outlet

Attic

Air

Outlet

Air

To Attic

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two per-

manent openings: one within 12" of the

ceiling and one within 12" of the floor.

Connect these items directly to the outdoors

orspacesopentotheoutdoors.Thesespaces

include attics and crawl spaces. Follow the

National Fuel Gas Code, NFPA 54/ANS

Z223.1,Section5.3,AirforCombustionand

Ventilation for required size of ventilation

grills or ducts.

Crawl

Space

Inlet

Air

Ventilated

Crawl Space

Inlet Air

Figure 3 - Ventilation Air from Outdoors

IMPORTANT: Do not provide openings

for inlet or outlet air into attic if attic has

a thermostat-controlled power vent.

Heated air entering the attic will activate

the power vent.

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

IMPORTANT:Vent-freeheatersaddmois- Carefullyfollowtheinstructionsbelow.This

ture to the air. Although this is beneficial, stove is a freestanding unit designed to set

installing heater in rooms without enough directly on the floor. IMPORTANT: You

ventilation air may cause mildew to form must maintain minimum wall and ceiling

from too much moisture. See Air for Com- clearances during installation. The mini-

bustion and Ventilation, pages 4 through 6. mum clearances are shown in Figure 4.

INSTALLATION

NOTICE: This heater is intended

foruseassupplementalheat.Use

this heater along with your pri-

mary heating system. Do not in-

stall this heater as your primary

heat source. If you have a central

heating system, you may run

system’scirculatingblowerwhile

using heater. This will help circu-

late the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

Measure from outermost point of stove top.

CHECK GAS TYPE

Minimum Wall and Ceiling

Clearances (see Figure 4)

A. Clearances from outermost point of

stove top to any combustible side wall

should not be less than 12 inches.

Use only natural gas. If your gas supply is

not natural gas, do not install heater. Call

dealer where you bought heater for proper

type heater.

CLEARANCES TO

COMBUSTIBLES

(Vent-Free Operation Only)

B. Clearances from outermost point of

stove top to any combustible back wall

should not be less than 6 inches (In-

cludes corner installations).

WARNING: A qualified ser-

vice person must install heater.

Follow all local codes.

C. Clearances from the stove top to the

ceiling should not be less than 48

inches.

WARNING:Maintainthemini-

mum clearances. If you can, pro-

vide greater clearances from

floor, ceiling, and adjoining side

and back walls.

WARNING: Never install the

heater

Ceiling

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other flammable

objectsarelessthan42inches

from the front, top, or sides of

the heater

Front View

48"

Minimum

12"

Minimum

12"

Minimum

Side Wall

• in high traffic areas

• in windy or drafty areas

CAUTION: This heater cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to heater. Installing

heater next to vinyl or cloth wall

coverings or operating heater

where impurities (such as to-

bacco smoke, aromatic candles,

cleaning fluids, oil or kerosene

lamps, etc.) in the air exist, may

discolor walls.

Top View

Back Wall

Minimum

Side View

Ceiling

Minimum

Side Wall

48"

Minimum

Corner

Wall

Back Wall

Minimum

Front of

Minimum

Stove Unit

Wall

Minimum

Floor

Figure 4 - Minimum Clearance to Walls and Ceiling

Continued

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE NATURAL GAS PEDESTAL STOVE

Apply pipe joint sealant lightly to male

INSTALLATION

WARNING: Never connect

heater to private (non-utility) gas

wells. This gas is commonly

known as wellhead gas.

threads. This will prevent excess sealant

from going into pipe. Excess sealant in pipe

could result in clogged heater valves.

Continued

CONNECTING TO GAS

SUPPLY

CAUTION:Usepipejointseal-

ant that is resistant to liquid pe-

troleum (LP) gas.

CAUTION: Use only new,

black iron or steel pipe. Inter-

nally-tinned copper tubing may

be used in certain areas. Check

yourlocalcodes. Usepipeof1/2"

diameter or greater to allow

proper gas volume to heater. If

pipe is too small, undue loss of

pressure will occur.

WARNING: A qualified service

personmustconnectheatertogas

supply. Follow all local codes.

We recommend that you install a sediment

trap in supply line as shown in Figure 6.

Locate sediment trap where it is within

reach for cleaning. Install in piping system

betweenfuelsupplyandheater.Locatesedi-

ment trap where trapped matter is not likely

to freeze. A sediment trap traps moisture

and contaminants. This keeps them from

going into heater controls. If sediment trap

is not installed or is installed wrong, heater

may not run properly.

Installation Items Needed

Beforeinstallingheater,makesureyouhave

the items listed below.

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection *

• sediment trap

Installation must include an equipment

shutoff valve, union, and plugged 1/8" NPT

tap. Locate NPT tap within reach for test

gauge hook up. NPT tap must be upstream

from heater (see Figure 6).

• tee joint

CAUTION: Avoid damage to

regulator.Holdgasregulatorwith

wrenchwhenconnectingittogas

piping and/or fittings.

• pipe wrench

IMPORTANT: Install equipment shutoff

valve in an accessible location. The equip-

ment shutoff valve is for turning on or

shutting off the gas to the appliance.

An CSA design-certified equipment

shutoff valve with 1/8" NPT tap is an ac-

ceptable alternative to test gauge connec-

tion. Purchase the optional CSA design-

certifiedequipmentshutoffvalvefromyour

dealer. See Accessories, page 22.

CSA Design-Certified Equipment

Shutoff Valve With 1/8" NPT Tap*

From Gas Meter

(5" W.C.** to 10.5"

W.C. Pressure)

Back View

Approved Flexible Gas Hose

(if allowed by local codes)

Tee Joint

Sediment

Pipe

Trap

Gas

Regulator

of Heater

Nipple

Side View

3" Minimum

Cap

Front

Figure 6 - Gas Connection

Stove

Unit

* Purchase the optional CSA design-certified equipment shutoff valve from your dealer.

Gas Regulator

Inlet Connection

See Accessories, page 22.

**Minimum inlet pressure for purpose of input adjustment.

Figure 5 - Gas Regulator Location and

Gas Line Access Into Stove Cabinet

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

Test Pressures Equal To or Less Than

1/2 PSIG (3.5 kPa)

Pressure Testing Heater Gas

Connections

1. Open equipment shutoff valve (see Fig-

ure 7).

INSTALLATION

Continued

1. Close equipment shutoff valve (see Fig-

ure 7).

CHECKING GAS

CONNECTIONS

2. Pressurize supply piping system by ei-

ther using compressed air or opening

main gas valve located on or near gas

meter.

2. Open main gas valve located on or near

gas meter.

3. Make sure control knob of heater is in

the OFF position.

WARNING: Test all gas pip-

ing and connections for leaks

after installing or servicing. Cor-

rect all leaks at once.

3. Check all joints from gas meter to

equipment shutoff valve (see Figure 8).

Apply mixture of liquid soap and water

to gas joints. Bubbles forming show a

leak.

4. Check all joints from equipment shutoff

valve to control valve (see Figure 8).

Apply mixture of liquid soap and wa-

ter to gas joints. Bubbles forming show

a leak.

WARNING:Neveruseanopen

flame to check for a leak. Apply a

mixture of liquid soap and water

toalljoints.Bubblesformingshow

a leak. Correct all leaks at once.

4. Correct all leaks at once.

5. Correct all leaks at once.

6. Light heater (see Operating Heater,

pages 11 and 12). Check all other in-

ternal joints for leaks.

Open

POSIT

Equipment

Shutoff

Valve

7. Turn off heater (see To Turn Off Gas to

Appliance, page 12).

Pressure Testing Gas Supply

Piping System

Closed

POS

Test Pressures In Excess Of 1/2 PSIG

(3.5 kPa)

Figure 7- Equipment Shutoff Valve

1. Disconnect appliance with its appliance

main gas valve (control valve) and equip-

ment shutoff valve from gas supply pip-

ing system. Pressures in excess of 1/2

psig will damage heater regulator.

Equipment Shutoff

Valve

2. Cap off open end of gas pipe where

equipment shutoff valve was connected.

Gas Meter

3. Pressurize supply piping system by ei-

ther using compressed air or opening

main gas valve located on or near gas

meter.

4. Check all joints of gas supply piping

system. Apply mixture of liquid soap

and water to gas joints. Bubbles form-

ing show a leak.

Control Valve Location

5. Correct all leaks at once.

6. Reconnect heater and equipment

shutoff valve to gas supply. Check re-

connected fittings for leaks.

Figure 8 - Checking Gas Joints

Continued

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE NATURAL GAS PEDESTAL STOVE

5. Install one plastic bushing provided in

INSTALLING BLOWER

ACCESSORY - GA3750

INSTALLATION

blower kit into the 1 ¹/2" hole in the left

Continued

rear of firebox floor. Access hole

through the rectangular opening in the

rear panel (see Figure 13).

Tools required: Phillips screwdriver

INSTALLING LOGS

NOTICE:Shutoffgasheaterduring

the following blower installation.

6. Remove the two blower mounting

brackets from the rear panel by remov-

ing two screws each (see Figure 14).

WARNING: Failure to position

thepartsinaccordancewiththese

diagrams or failure to use only

parts specifically approved with

this heater may result in property

damage or personal injury.

1. Remove top panel of stove by remov-

ing three screws from under top lip on

each side of stove (see Figure 11).

7. Attach the two mounting brackets to

blower housing using four screws pro-

vided in blower kit (2 for each bracket)

(see Figure 14). Tighten screws se-

curely. Place blower assembly tempo-

rarily on top of firebox.

2. Facing front of stove, carefully slide top

panel forward until it is completely re-

moved from stove (see Figure 11).

CAUTION:Afterinstallationand

periodicallythereafter,checktoen-

surethatnoflamecomesincontact

with any log. With the heater set to

High,checktoseeifflamescontact

any log. If so, reposition logs ac-

cording to the log installation in-

structions in this manual. Flames

contacting logs will create soot.

3. Disconnect power cord wires from blower

motor (if connected) (see Figure 12).

8. Working from the rear of the stove,

place entire power cord, including

speed control housing, in lower control

compartment.

4. Disconnect green ground wire from

blower housing (if connected) by re-

moving screw holding wire terminal

(see Figure 12).

9. Route ends of 3-wire power cord up

from the lower control compartment

through the plastic bushing, then up to

the upper cavity of stove (see Figure 15).

10. Attach the terminal ends of the white

and black power cord wires to the ter-

minals on the blower motor (see Fig-

ure 14). Push firmly.

Itisveryimportanttoinstallthelogsexactly

as instructed. Do not modify logs. Only use

logs supplied with heater.

Place one-piece log set on grate to fit as

illustratedinFigure9.Makesurelogsitsflat

on firebox floor (see Figure 9).

IMPORTANT:Makesurelogdoesnotcover

any burner ports (see Figure 10).

11. Attach the terminal end of the green

power cord wire to the front tab of the

blower housing using screw provided

(see Figure 12).

Figure 11 - Removing Stove Top Panel

12. Using the four screws previously re-

moved, mount blower assembly to

stove by reattaching blower brackets to

rear panel (see Figure 14). Tighten

screws securely.

White Powercord Wire

Black Powercord Wire

One Piece

Log Set

Blower

Bracket

I ^P

Screw

Green

Ground Wire

Blower

Figure 12 - Removing Wires from Blower

Firebox Floor

Figure 9 - Installing One-Piece Log Set

Burner Ports

One Piece Log Set

Figure 13 - Installing Bushing

Firebox Top

Figure 14 - Removing Blower Brackets

from Stove and Attaching to Blower

Figure 10 - Installing One-Piece Log set

(Top View)

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

INSTALLATION

OPERATING HEATER

WARNING: ELECTRICAL

Continued

GROUNDING INSTRUCTIONS

Thisapplianceisequippedwitha

three-prong (grounding) plug for

your protection against shock

hazard and should be plugged

directly into a properly grounded

three-prong receptacle.

FOR YOUR SAFETY

READ BEFORE

LIGHTING

13. Install plastic control knob onto output

shaft of speed control housing (see Fig-

ure 15). Place speed control housing

just inside control compartment door

in front of stove (see Figure 16).

WARNING: If you do not fol-

low these instructions exactly, a

fireorexplosionmayresultcaus-

ing property damage, personal

injury or loss of life.

14. Using two screws provided in blower

kit, mount blower speed control hous-

ing to mounting tab in left side of lower

control compartment (see Figure 16).

19. Using speed control knob, turn blower

on and check for operation.

20. All remaining parts from blower kit

may be discarded.

15. Check to make sure that the power cord is

completelyclearofblowerwheelandthere

are no foreign objects in blower wheel.

A. This appliance has a pilot which must

be lighted by hand. When lighting the

pilot, follow these instructions exactly.

16. Carefully replace stove top panel.Align

holes and replace six screws removed

in step 1.

B. BEFORE LIGHTING smell all

around the appliance area for gas. Be

sure to smell next to the floor because

some gas is heavier than air and will

settle on the floor.

17. Peel off the backing paper and stick

the supplied wiring diagram decal on

the stove floor bottom as shown in

Figure 15.

WHATTO DO IFYOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow

the gas supplier’s instructions.

Blower Speed

Control Housing

18. Plugpowercordintoaconvenient3-prong

grounded wall receptacle near the stove.

Figure16-InstallingBlowerControlHousing

• If you cannot reach your gas sup-

plier, call the fire department.

C. Use only your hand to push in or turn

the gas control knob. Never use tools.

If the knob will not push in or turn

by hand, don’t try to repair it, call a

qualified service technician or gas

supplier. Force or attempted repair

may result in a fire or explosion.

WARNING: Never attempt to service heater while it

is plugged in, operating, or hot. Burns and electrical

shock could result. Only a qualified service person

should service or repair heater.

If any of the original wire as supplied with the appliance must be

replaced, it must be replaced with 105°C wire or it’s equivalent.

D. Do not use this appliance if any part

has been under water. Immediately call

a qualified service technician to inspect

the appliance and to replace any part

of the control system and any gas con-

trol which has been under water.

WARNING: Label all wires prior to disconnection

when servicing controls. Wiring errors can cause im-

proper and dangerous operation. Verify proper opera-

tion after servicing.

Power

Cord

Variable

Fan Switch

Off

110/115

V.A.C.

Blower

Motor

Black

Green

White

Black

White

Wiring

Diagram

Decal

Speed Control

Control

120 Vac. 60 Hz. . 78 Amps

DESA International, Bowling Green, KY

101584-05

Housing

Knob

Figure 15 - Routing Power Cord

Continued

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE NATURAL GAS PEDESTAL STOVE

7. Keep control knob pressed in for 30

MANUAL LIGHTING

OPERATING

seconds after lighting pilot. After 30

seconds, release control knob.

• Ifcontrolknobdoesnotpopoutwhen

released, contact a qualified service

person or gas supplier for repairs.

PROCEDURE

HEATER

1. Follow steps 1 through 5 under Light-

ing Instructions.

Continued

LIGHTING

INSTRUCTIONS

2. Depress control knob and light pilot

with match.

Note: If pilot goes out, repeat steps 3

through 7.This heater has a safetyinter-

lock system.Wait one (1) minute for sys-

tem to reset before lighting pilot again.

3. Keep control knob pressed in for 30

seconds after lighting pilot. After 30

seconds, release control knob. Now

follow step 8 in column 2.

NOTICE: During initial operation

of new heater, burning logs will

give off a paper-burning smell.

Orange flame will also be present.

Open a window to vent smell. This

will only last a few hours.

8. Turn control knob counterclockwise

C-clockwise

to desired heating level. The

burners should light. Set control knob

to any heat level between HI and LO.

INSPECTING

BURNERS

1. STOP! Read the safety information,

page 11, column 3.

Ignitor Electrode

Check pilot flame pattern and burner flame

patterns often.

Thermocouple

Pilot Burner

2. Make sure equipment shutoff valve

is fully open.

PILOT FLAME PATTERN

3. Turn control knob clockwise

to the OFF position.

Clockwise

Figure 19 shows a correct pilot flame pat-

tern. Figure 20 shows an incorrect pilot

flame pattern. (Note: Appearance of pilot

assembly may vary by model). The incor-

rect pilot flame is not touching the thermo-

couple. This will cause the thermocouple to

cool.Whenthethermocouplecools,theheater

will shut down.

4. Wait five (5) minutes to clear out any

gas. Then smell for gas, including

near the floor. If you smell gas,

STOP! Follow “B” in the safety in-

formation, page 11, column 3. If you

don’t smell gas, go to the next step.

Figure 18 - Pilot

CAUTION:Donottrytoadjust

heatinglevelsbyusingtheequip-

ment shutoff valve.

5. Turn control knob counterclockwise

TO TURN OFF GAS

TO APPLIANCE

to the PILOT position.

C-clockwise

If pilot flame pattern is incorrect, as shown

in Figure 20

Press in control knob for five (5) sec-

onds (see Figure 17). Note:You may

be running this heater for the first

• turn heater off (see To Turn Off Gas to

Appliance)

Shutting Off Heater

time after hooking up to gas supply. Turn control knob clockwise

If so, the control knob may need to the OFF position.

be pressed in for 30 seconds or less.

Clockwise

• see Troubleshooting, pages 14 through 16

Shutting Off Burners Only (pilot

stays lit)

Pilot Burner

Thermocouple

This will allow air to bleed from the

gas system.

Turn control knob clockwise

the PILOT position.

Clockwise

6. With control knob pressed in, press

and release ignitor button. This will

light pilot. The pilot is attached to the

front burner. If needed, keep press-

ing ignitor button until pilot lights.

THERMOSTAT CONTROL

OPERATION

The thermostat control knob can be set to

Figure 19 - Correct Pilot Flame Pattern

Note: If pilot does not stay lit, con-

tact a qualified service person or gas any comfort level between Hi and Lo. The

supplier for repairs. Until repairs are thermostatwillgraduallymodulatetheheat

Thermocouple

Pilot Burner

made, light pilot with match. To light

output and flame height from higher to

pilot with match, see Manual Light- lower settings, or pilot, in order to maintain

ing Procedure.

the comfort level you select. The ideal com-

fort setting will vary by household depend-

ing upon the amount of space to be heated,

the output of the central heating system, etc.

Control Knob

Ignitor Button

Note: Selecting the Hi setting with the

control knob will cause the burners to

remainfullyon,withoutmodulatingdown

in most cases.

Figure 20 - Incorrect Pilot Flame Pattern

Figure 17- Control Knob and Ignitor

Button Location

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

Burner

Tube

CLEANING BURNER

INJECTOR HOLDER AND

PILOT AIR INLET HOLE

INSPECTING

Injector Holder

BURNERS

Continued

The primary air inlet holes allow the proper

amount of air to mix with the gas. This pro-

videsacleanburningflame. Keeptheseholes

clearofdust,dirt,lint,andpethair.Cleanthese

air inlet holes prior to each heating season.

Blockedairholeswillcreatesoot. Werecom-

mend that you clean the unit every three

months during operation and have heater in-

spected yearly by a qualified service person.

BURNER FLAME PATTERN

Primary Air

Inlet Holes

Figure 21 shows a correct burner flame pat-

tern. Figure 22 shows an incorrect burner

flame pattern. If burner flame pattern is

incorrect,

Figure 23 - Injector Holder On Outlet

Burner Tube

Ports/Slots

• turn heater off (see To Turn Off Gas to

Appliance, page 12)

Burner

Tube

• see Troubleshooting, pages 14 through 16

Wealsorecommendthatyoukeeptheburner

tubeandpilotassemblycleanandfreeofdust

and dirt. To clean these parts we recommend

using compressed air no greater than 30 PSI.

Yourlocalcomputerstore,hardwarestore,or

home center may carry compressed air in a

can. You can use a vacuum cleaner in the

blow position. If using compressed air in a

can, please follow the directions on the can.

If you don't follow directions on the can, you

could damage the pilot assembly.

Approx. 3-6" Above

Top of Logs

Pilot

Assembly

Pilot Air

Inlet

Hole

Figure 21 - Correct Flame Pattern with

Control Knob Set to High Flame.

Figure 24 - Pilot Inlet Air Hole

1. Shut off the unit, including the pilot.

Allow the unit to cool for at least thirty

minutes.

More Than 8"

Above Top of Logs

CABINET

Air Passageways

• Use a vacuum cleaner or pressurized air

to clean.

2. Inspect burner, pilot, and primary air

inlet holes on injector holder for dust

and dirt (see Figure 23).

Exterior

3. Blow air through the ports/slots and

holes in the burner.

• Use a soft cloth dampened with a mild

soap and water mixture. Wipe the cabi-

net to remove dust.

4. Check the injector holder located at the

end of the burner tube again. Remove any

large particles of dust, dirt, lint, or pet hair

with a soft cloth or vacuum cleaner nozzle.

Figure 22 - Incorrect Flame Pattern with

Control Knob Set to High Flame

LOGS

• If you remove logs for cleaning, refer to

Installing Logs, page 10, to properly re-

place logs.

5. Blow air into the primary air holes on

the injector holder.

CLEANING AND

MAINTENANCE

6. In case any large clumps of dust have

now been pushed into the burner repeat

steps 3 and 4.

• Replace log(s) if broken or chipped

(dime-sized or larger).

WARNING: Turn off heater

and let cool before cleaning.

MAIN BURNER

Clean the pilot assembly also. A yellow tip on

thepilotflameindicatesdustanddirtinthepilot

assembly. There is a small pilot air inlet hole

about two inches from where the pilot flame

comesoutofthepilotassembly(seeFigure24).

Withtheunitoff,lightlyblowairthroughtheair

inlet hole. You may blow through a drinking

straw if compressed air is not available.

Periodically inspect all burner flame holes

with the heater running. All slotted burner

flame holes should be open with yellow

flame present. All round burner flame holes

should be open with a small blue flame

present. Some burner flame holes may be-

comeblockedbydebrisorrust,withnoflame

present. If so, turn off heater and let cool.

Either remove blockage or replace burner.

Blocked burner flame holes will create soot.

CAUTION: You must keep con-

trol areas, burner, and circulating

air passageways of heater clean.

Inspect these areas of heater be-

fore each use. Have heater in-

spected yearly by a qualified ser-

viceperson.Heatermayneedmore

frequentcleaningduetoexcessive

lint from carpeting, bedding mate-

rial, pet hair, etc.

Reviewyourvideoincludedwithyourheater

for additional cleaning instructions.

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE NATURAL GAS PEDESTAL STOVE

TROUBLESHOOTING

CAUTION: Never use a wire,

needle, or similar object to clean

ODS/pilot.ThiscandamageODS/

pilot unit.

WARNING: Turn off heater

andletcoolbeforeservicing.Only

aqualifiedservicepersonshould

service and repair heater.

Note: For additional help, visit DESA

International’stechnicalservicewebsite

at www.desatech.com.

Note:Alltroubleshootingitemsarelistedin

order of operation.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

When ignitor button is pressed, there is no 1. Ignitor electrode not connected to igni- 1. Reconnect ignitor cable

spark at ODS/pilot

tor cable

2. Ignitor cable pinched or wet

2. Free ignitor cable if pinched by any

metal or tubing. Keep ignitor cable dry

3. Tighten nut holding piezo ignitor to base

panel of log set. Nut is located behind

base panel

3. Piezo ignitor nut is loose

4. Broken ignitor cable

4. Replace ignitor cable

5. Bad piezo ignitor

5. Replace piezo ignitor

6. Ignitor electrode broken

7. Ignitor electrode positioned wrong

6. Replace piezo ignitor

7. Replace piezo ignitor

When ignitor button is pressed, there is 1. Gas supply turned off or equipment 1. Turn on gas supply or open equipment

spark at ODS/pilot but no ignition

shutoff valve closed

shutoff valve

2. Control knob not in PILOT position

2. Turn control knob to PILOT position

3. Control knob not pressed in while in 3. Press in control knob while in PILOT

PILOT position

position

4. Air in gas lines when installed

4. Continue holding down control knob.

Repeat igniting operation until air is re-

moved

5. ODS/pilot is clogged

5. Clean ODS/pilot (see Cleaning and

Maintenance, page 13) or replace ODS/

pilot assembly

6. Gas regulator setting is not correct

6. Replace gas control

ODS/pilot lights but flame goes out when 1. Control knob not fully pressed in

1. Press in control knob fully

control knob is released

2. Control knob not pressed in long enough 2. After ODS/pilot lights, keep control

knob pressed in 30 seconds

3. Equipment shutoff valve not fully open 3. Fully open equipment shutoff valve

4. Pilot flame not touching thermocouple, 4. A) Contact local natural gas company

which allows thermocouple to cool,

causing pilot flame to go out. This prob-

lem could be caused by one or both of

the following:

B) Clean ODS/pilot (see Cleaning and

Maintenance, page 13) or replace ODS/

pilot assembly

A) Low gas pressure

B) Dirty or partially clogged ODS/pilot

5. Thermocouple connection loose at con- 5. Hand tighten until snug, then tighten 1/4

trol valve

turn more

6. Thermocouple damaged

7. Control valve damaged

6. Replace thermocouple

7. Replace control valve

www.desatech.com

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

TROUBLESHOOTING

Continued

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

Burner does not light after ODS/pilot is lit

1. Burner orifice clogged

1. Clean burner (see Cleaning and Mainte-

nance, page 13) or replace burner orifice

2. Contact local natural gas company

2. Inlet gas pressure is too low

3. Burner orifice diameter is too small

3. Replace burner orifice

4. Thermopile leads disconnected or im- 4. Reconnect leads (see wiring diagram)

properly connected

5. Burners will not come on in remote position 5. Replace battery in transmitter and receiver

Delayed ignition burner

1. Manifold pressure is too low

2. Burner orifice clogged

1. Contact local natural gas company

2. Clean burner (see Cleaning and Mainte-

nance, page 13) or replace burner orifice

Burner backfiring during combustion

1. Burner orifice is clogged or damaged

1. Clean burner (see Cleaning and Mainte-

nance, page 13) or replace burner orifice

2. Replace damaged burner

2. Damaged burner

3. Gas regulator defective

3. Replace gas control

Slight smoke or odor during initial operation 1. Not enough air

1. Check burner for dirt and debris. If found,

clean burner (see Cleaning and Mainte-

nance, page 13)

2. Gas regulator defective

2. Replace gas control

3. Residues from manufacturing processes 3. Problem will stop after a few hours of

and logs curing

operation

Moisture/condensation noticed on windows 1. Not enough combustion/ventilation air

1. Refer to Air for Combustion and Ventila-

tion requirements (page 4)

Heater produces a whistling noise when 1. Turning control knob to HI position when 1. Turn control knob to LO position and let

burner is lit

burner is cold

warm up for a minute

2. Air in gas line

2. Operate burner until air is removed from

line. Have gas line checked by local natu-

ral gas company

3. Air passageways on heater blocked

3. Observe minimum installation clearances

(see pages 7 through 9)

4. Dirty or partially clogged burner orifice

4. Clean burner (see Cleaning and Mainte-

nance, page 13) or replace burner orifice

Dark residue on logs or inside of fireplace

1. Improper log placement

1. Properly locate logs (see Installing Logs,

page 10)

2. Drafts or other air currents affecting 2. Eliminate source of drafts around heater

flame pattern

3. Air holes at burner inlet blocked

3. Clean out air holes at burner inlet. Peri-

odically repeat as needed

4. Burner flame holes blocked

4. Remove blockage or replace burner

Whitepowderresidueformingwithinburner 1. When heated, vapors from furniture pol- 1. Turn heater off when using furniture pol-

box or on adjacent walls or furniture

ish, wax, carpet cleaners, etc. turn into

white powder residue

ish, wax, carpet cleaners, or similar

products

Continued

www.desatech.com

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE NATURAL GAS PEDESTAL STOVE

TROUBLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your

building.

• Immediatelycallyourgassupplierfromaneighbor’sphone.Followthe

gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning

supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles,

etc., create fumes. These fumes may mix with combustion air and create odors. These odors

will disappear over time.

POSSIBLE CAUSE

OBSERVED PROBLEM

REMEDY

1. Metal expanding while heating or con-

tracting while cooling

Heater produces a clicking/ticking noise

just after burner is lit or shut off

1. This is common with most heaters. If

noise is excessive, contact qualified ser-

vice person

1. Heater burning vapors from paint, hair

spray, glues, cleaners, chemicals, new

carpet, etc. (See IMPORTANT state-

ment above)

Heater produces unwanted odors

1. Open window and ventilate room. Stop

using odor causing products while heater

is running

2. Gas leak. SeeWarning statement at

top of page

2. Locate and correct all leaks (see Check-

ing Gas Connections, page 9)

1. Not enough fresh air is available

2. Low line pressure

3. ODS/pilot is partially clogged

Heater shuts off in use (ODS operates)

1. Open window and/or door for ventilation

2. Contact local natural gas company

3. Clean ODS/pilot (see Cleaning and

Maintenance, page 13)

1. Gas leak. SeeWarning statement at

top of page

2. Control valve defective

Gas odor even when control knob is in OFF

position

1. Locate and correct all leaks (see Check-

ing Gas Connections, page 9)

2. Replace control valve

1. Foreign matter between control valve

and burner

Gas odor during combustion

1. Take apart gas tubing and remove for-

eign matter

2. Gas leak. SeeWarning statement at

top of page

2. Locate and correct all leaks (see Check-

ing Gas Connections, page 9)

1. Excessive line or manifold pressure

2. Dirty primary air holes

Burner flame is excessively large and is

very near or touches the top of firebox

1. Check manifold pressure and correct as

needed

2. Clean burner air holes (see Cleaning and

Maintenance, page13).

www.desatech.com

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

SPECIFICATIONS

PARTS CENTRALS

These Parts Centrals are privately owned businesses. They have agreed to support our

customer’s needs by providing original replacement parts and accessories.

Btu (Variable)

Type Gas

20,000/26,000

Natural Only

Piezo

Ignition

Baltimore Electric

1348 Dixwell Avenue

Hamden, CT 06514-0322

1-800-397-7553

203-248-7553

Parts Department

East Coast Energy Products

707 Broadway

W. Long Branch, NJ 07764-1542

732-870-8809

1-800-755-8809

Manifold Pressure

3.0" W.C.

Inlet Gas Pressure

(in. of water) *

Maximum

Minimum

Dimensions, Inches (H x W x D)

Stove

Carton

Weight, pounds

Stove

10.5"

www.njplaza.com/ecep

24 x 27 ¹/4 x 17 ¹/4

22 x 31 x 31 ¹/2

Portable Heater Parts

342 N. County Rd. 400 East

Valparaiso, IN 46383-9704

All States

219-462-7441

1-800-362-6951

Dayton Hardware

P.O. Box 275

North Dayton Station

Dayton, OH 45404-0275

All States

66 lbs.

80 lbs.

Shipping

937-258-3721

OH 1-800-762-3426

* For purposes of input adjustment

[email protected]

Halco Enterprises

208 Carter Drive, Unit 21

West Chester, PA 19382-4500

610-430-7717

1-800-368-0803

www.halcoenterprises.com

SERVICE HINTS

FBD

When Gas Pressure Is Too Low

• pilot will not stay lit

1349 Adams Street

Bowling Green, KY 42103-3414

270-846-1199

• burners will have delayed ignition

• heater will not produce specified heat

• natual gas supply may be low

1-800-654-8534

Fax: 1-800-846-0090

[email protected]

Laporte’s Parts & Service

2444 N. 5th Street

Hartsville, SC 29550-7704

803-332-0191

Parts Department

When Gas Quality Is Bad

• pilot will not stay lit

Master Parts Dist.

1251 Mound Ave NW

Grand Rapids, MI 49504-2672

616-791-0505

1-800-446-1446

Fax: 616-791-8270

www.nbmc.com

• burners will produce flames and soot

• heater will backfire when lit

Cans Unlimited, Inc.

P.O. Box 645

Taylor, SC 29687-0013

All States

803-879-3009

Youmayfeelyourgaspressureistoolowor

gas quality is bad. If so, contact your local

natural gas supplier.

Washer Equipment Co.

1715 Main Street

Kansas City, MO 64108-2195

KS, MO, AR

816-842-3911

www.washerparts.com

1-800-845-5301

[email protected]

TECHNICAL

SERVICE

You may have further questions about in-

stallation, operation, or troubleshooting.

If so, contact DESA International’s Techni-

calServiceDepartmentat1-800-DESALOG

(1-800-337-2564).

You can also visit DESA International’s

technical services web site at

www.desatech.com.

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE NATURAL GAS PEDESTAL STOVE

ILLUSTRATED

PARTS

BREAKDOWN

S26NT

105683

Download from Www.Somanuals.com. All Manuals Search And Download.

For more information, visit www.desatech.com

OWNER’S MANUAL

This list contains replaceable parts used in your heater. When ordering parts, follow the

instructions listed under Replacement Parts on page 22 of this manual.

PARTS LIST

S26NT

KEY PART

NO.

NUMBER

DESCRIPTION

QTY.

106039-01

14285-01

Log Set

ODS Pilot (NG)

ODS Nut

Burner Outlet Tube

Injector Holder

Burner Clip

Burner Orifice Injector

Gas Control Valve

Burner

098249-01

105973-01

105737-01

102843-01

099056-27

101329-25

102980-01

099387-09

098271-07

101381-01

L98515-01

L98303-01

105972-01

Pilot Tube

Ignitor Cable

Piezo Ignitor and Cover

Pilot Shield

Regulator

Inlet Tube

PARTS AVAILABLE — NOT SHOWN

100563-01

101054-01

Warning Plate

Lighting Instructions Plate

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE NATURAL GAS PEDESTAL STOVE

ILLUSTRATED

PARTS

BREAKDOWN

S26NT

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

Thislistcontainsreplaceablepartsusedinyourheater. Whenorderingparts, followtheinstructions

listed under Replacement Parts on page 22 of this manual.

PARTS LIST

S26NT

KEY

NO.

PART NO.

DESCRIPTION

QTY.

105666-01

105656-01

105655-01

105654-01

105653-01

105657-01

105658-01

105659-01

105660-01

105661-01

105970-01

101382-01

105672-01

105673-01

106754-01

105971-01

099230-02

106020-01

Top Panel, Stove

Pedestal Stove

Stove Base

Stove Back Panel

Louver Panel

Blower Bracket

Door

Firebox Back Panel

Firebox Floor

Firebox Top Assembly

Screen Assembly

Valve Bracket

Brass Trim, Bottom

Brass Trim, Firebox

Knob

Door Hinge

Shoulder Screw

Heat Deflector

PARTS AVAILABLE — NOT SHOWN

101054-01

100563-01

104310-10

104108-06

Lighting Instructions Plate

Warning Plate

Information Video

Touch-Up Paint Kit (12 oz. can)

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT-FREE NATURAL GAS PEDESTAL STOVE

CLEANING KIT - CCK

(Not Shown)

REPLACEMENT

PARTS

ACCESSORIES

Purchasetheseheateraccessoriesfromyour

localdealerorPartsCentral(seepage17). If

they cannot supply these accessories call

Your vent-free gas appliance requires regu-

lar cleaning and maintenance to prevent

performance problems. This kit gives you

the tools and instructions to make it easy to

clean all critical areas of your appliance.

Note: Use only original replacement parts.

This will protect your warranty coverage DESA International’s Sales Department at

for parts replaced under warranty.

1-800-458-2472 for referral information.

You can also write to the address listed on

the back page of this manual.

PARTS UNDER WARRANTY

Contact authorized dealers of this product.

If they can’t supply original replacement

part(s)callDESAInternational’sTechnical

Service Department at 1-800-323-5190 for

referral information.

WhencallingDESAInternational,haveready

• your name

• your address

• model and serial numbers of your heater

• how heater was malfunctioning

• type of gas used (propane/LP or natural gas)

• purchase date

EQUIPMENT SHUTOFF

VALVE - GA5010

Usually, we will ask you to return the defec-

tive part to the factory.

Equipmentshutoffvalvewith1/8"NPTtap.

PARTS NOT UNDER

WARRANTY

Contact authorized dealers of this product

or Parts Central (see page 17). If they can’t

supply original replacement part(s) call

DESA International’s Parts Department at

1-800-972-7879 for referral information.

WhencallingDESAInternational,haveready

• model number of your heater

MANUALLY-CONTROLLED

BLOWER KIT - GA3750

• the replacement part number

Provides better heat distribution. Features

variable speed control knob.

105683

For more information, visit www.desatech.com

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

NOTES

_______________________________________________________________________________________________

105683

Download from Www.Somanuals.com. All Manuals Search And Download.

For more information, visit www.desatech.com

WARRANTY INFORMATION

KEEP THIS WARRANTY

Model

Serial No.

Date Purchased

Always specify model and serial numbers when communicating with the factory.

We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard

written warranty. We make no other warranty, expressed or implied.

LIMITED WARRANTY

VENT-FREE NATURAL GAS PEDESTAL STOVE

DESA International warrants this product to be free from defects in materials and components for two (2) years from the date

of first purchase, provided that the product has been properly installed, operated and maintained in accordance with all

applicable instructions. To make a claim under this warranty the Bill of Sale or cancelled check must be presented.

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this

heatertoproperoperatingconditionandanallowanceforlaborwhenprovidedbyaDESAAuthorizedServiceCenter.Warranty

part(s) MUST be obtained through authorized dealers of this product and/or DESA International who will provide original

factory replacement parts. Failure to use original factory replacement parts voids this warranty. The heater MUST be installed

by a qualified installer in accordance with all local codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or

becomedamagedasaresultofmisuse, accidents, lackofpropermaintenanceordefectscausedbyimproperinstallation. Travel,

diagnostic cost, labor, transportation and any and all such other costs related to repairing a defective heater will be the

responsibility of the owner.

TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE

PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND

LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO TWO (2) YEARS ON ALL COMPONENTS

FROM THE DATE OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO

THE PURCHASE PRICE OF THE PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY

OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or

consequentialdamages, sotheabovelimitationonimpliedwarranties, orexclusionorlimitationondamagesmaynotapplytoyou.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

For information about this warranty write:

INTERNATIONAL

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

www.desatech.com

105683-01

Rev. C

105683 01

09/00

NOT A UPC

Download from Www.Somanuals.com. All Manuals Search And Download.

Cognitive Solutions Printer DD2424 User Manual
Cranium Games Jungle Adventure User Manual
Cuisinart Coffeemaker DCC 1400C User Manual
Dual Marine RADAR MDM300 User Manual
Electro Voice Speaker System Force i User Manual
Fellowes Paper Shredder 220C 2 User Manual
FieldServer Computer Drive FS 8700 82 User Manual
Fisher Paykel Ice Maker E331TL User Manual
Furman Sound Power Supply PL PRO E II User Manual
Fusion Car Stereo System CA CD500 User Manual