ꢁ Termination Resistance Setup Switch
繁體中文
注意事項
ꢃ
Approx. 30mm
The termination resistance switch is used for determining whether the resistance is valid.
ON = Valid; OFF = Invalid
ꢀ
ꢀ
ꢀ
ꢀ
請在使用前，務必仔細閱讀本使用手冊，並按照本手冊指示進行操作，以免造成產品受損，或導致人員受傷。
實施配線，務必關閉電源。
ON
Use efficient tool to peel the communication cable for
approx. 30mm. DO NOT damage the shielded cable
while peeling.
①
OFF
本使用說明書僅提供電氣規格、功能規格、安裝配線及周邊裝置部分說明。
ꢁ Termination Resistance
本機為開放型 (OPEN TYPE) 機殼，因此使用者使用本機時，必須安裝於具防塵、防潮及免於電擊∕衝擊意
外的外殼配線箱內。另必須具備保護措施（如：特殊的工具或鑰匙才可打開），防止非維護人員操作或意外
衝擊本體，造成危險及損壞。請勿在上電時觸摸任何端子。
Shielded cable
Peel off the metallic shielded net and foil, and you will
find 2 power cables (in red and black), 2 signal cables
(in blue and white) and 1 shielded cable.
②
③
④
TAP-CP01 formulates a 121
Ω
termination resistance.
ꢀ
ꢀ
為避免損壞本產品，只有合格且熟悉本產品結構及操作的專業人員才可進行本產品的安裝、操作、配線及維
護。
交流輸入電源不可連接於輸入∕輸出訊號端，否則可能造成嚴重損壞。請在上電前再次確認電源配線，且請
勿在上電時觸摸任何端子。本體上的接地端子
務必正確的接地，以提高產品抗雜訊能力。
ꢁ Fuse
Peel off the exterior metallic shielded net, foil and the
plastic cover of the power cable and signal cable in
proper length.
ꢀ 產品簡介
TAP-CP01 formulates two 7.5A fuses, EF1 and EF2.
Black (V-)
謝謝您使用台達 TAP-CP01 電源分接盒。TAP-CP01 定義為 DeviceNet 電源分接盒，為 DeviceNet 提供網路電源。
Blue (CAN_L)
Shielded cable (CAN_SHLD)
TB1
與
TB2 用於連接 DeviceNet 匯流排，J1 用於連接電源，EF1
和
EF2 用於連接兩個 7.5A 的熔斷器。TAP-CP01
Insert the peeled communication cables into the holes in
the connector in correct order.
集成一個 121Ω的終端電阻，並通過開關來切換是否有效。
ꢄNotes:
When you are using the fuse and remove the fuse from the slot, the network power supply for the corresponding branch
will be cut off. For example, once EF1 is removed, the network power supply for the bus connected at TB1 will be cut off.
Red (V+)
White (CAN_H)
ꢁ 產品外觀及各部介紹
53.9
[2.12]
1
2
3
4
5
6
7
8
DeviceNet 匯流排通訊連接器
DeviceNet 匯流排通訊連接器
7.5A 熔斷器
71.2
[2.80]
ꢇ
The entire network can contain only one earth point to avoid circulating current.
Tighten the screws on the connector by a slotted
screwdriver and fix the communication cables in the
holes in the connector.
⑤
Screw by a slotted screwdriver.
7.5A 熔斷器
ꢁ Single Power Supply
121Ω終端電阻
Connect V- and the shielded cable to the earth using 25mm copper net or 8AWG copper cable of length shorter
than 3m.
Use standard 35mm DIN rail.
⑥
⑦
終端電阻設置開關
網路電源連接器
DIN 軌槽
Install TAP-CP01 onto the DIN rail.
V-
V-
L
尺寸單位：mm [inch]
L
S
H
S
H
V+
V+
ꢂ 功能規格
EF2
EF1
J1
ꢁ 電氣規格
V+
V-
S
V+
V-
電壓規格：11 ~ 25V DC
電源輸入
電流規格：最大7.5A
V+
V-
Power Supply
Power Supply
ꢁ 環境規格
ꢁ Multi Power Supply
操作：0ºC ~ 55ºC（溫度）、50 ~ 95%（濕度）、污染等級
2
操作∕儲存環境
When many power supplies are connected in a network, connect V- to V- and disconnect V+ to V+. Only one
earth point is allowed in the network.
儲存：-25ºC ~ 70ºC（溫度）、5 ~ 95%（濕度）
Insert the connector into TAP-CP01.
⑧
V-
V-
L
V-
V-
L
ꢃ 安裝說明
ENGLISH
L
L
S
S
S
S
大約 30mm
ꢀ
Please read this instruction sheet carefully before use and follow the sheet to operate TAP-CP01 in order to prevent
damages on the device or injuries to staff.
H
H
H
H
請使用專業工具將通訊電纜剝開大約 30mm，在剝線過程
①
V+
EF2
V+
EF2
V+
V+
EF1
EF1
中注意不要損壞遮罩線。
ꢀ
ꢀ
Switch off the power before wiring.
Disconnect V+
J1
J1
Insert the communication connector into
TAP-CP01 communication terminal.
This instruction sheet only provides introductory information on electrical specifications, functions, wiring,
trouble-shooting and peripherals for TAP-CP01.
V+ V-
S
V+ V-
S
遮蔽線
V+
V-
V+
V-
V+
V-
V+
V-
ꢀ
TAP-CP01 is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity,
electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key
or specific tools are required to open the enclosure) in case danger and damage on the device may occur. DO NOT
touch any terminal when the power is switched on.
One earth
point only.
Connect 24VDC power supply to
TAP-CP01 network power supply
connector.
剝開外層的金屬遮罩網和鋁箔，你會看到
2
根電源線（紅
②
③
Power Supply
Power Supply
Power Supply
Power Supply
色和黑色）
、
2
根訊號線（藍色和白色）
、1
根遮罩線。
ꢄNotes:
1. Use only wires specifically designed for DeviceNet wiring.
ꢀ
ꢀ
In order not to damage it, only qualified professional staff familiar with the structure and operation of TAP-CP01
can stall, operate, wire and repair it.
ꢈ
Establishing a network through TAP-CP01:
2. DO NOT place the signal cable and power cable in the same wiring circuit.
去除外層的金屬遮罩網和鋁箔，然後剝去電源線以及訊號
線的塑膠表皮，剝開的長度要適當。
DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check all
the wiring again before switching on the power and DO NOT touch any terminal when the power is switched on.
ꢅ
Make sure the ground terminal
is correctly grounded in order to prevent electromagnetic interference.
黑色(V-)
藍色(CAN_L)
V-
L
V-
L
遮蔽線(CAN_SHLD)
ꢀ
將剝開的通訊電纜按照正確的順序嵌入通訊連接器的線
孔內，如右圖所示。
④
Thank you very much for choosing Delta TAP-CP01 Power Supply Distribution Box. TAP-CP01 supplies power
to DeviceNet. TB1 and TB2 connect to DeviceNet cable. J1 connects to the power supply. EF1 and EF2
S
S
紅色(V+)
白色(CAN_H)
H
H
connect to two 7.5A fuses. TAP-CP01 formulates a 121
Ω
termination resistance, which is switched by a setup
V+
V+
switch.
EF1
EF2
使用標準的一字起子旋緊通訊連接器的螺絲，將通訊電纜
固定於通訊連接器的線孔內。
⑤
ꢁ Product Profile & Outline
53.9
[2.12]
1
2
3
4
5
6
7
8
DeviceNet cable connector
DeviceNet cable connector
7.5A fuse
71.2
[2.80]
S
V+ V-
J1
使用標準的一字起子旋緊
請使用 35mm 的標準 DIN 軌。
⑥
⑦
To install TAP-CP01 at the starting point or end point of the network, you have to switch ON the termination
resistance. To install TAP-CP01 in the middle of the network, you have to switch OFF the termination
resistance.
①
ꢆ
將
TAP-CP01 固定在 DIN 軌上，如下圖所示：
7.5A fuse
ꢁ DeviceNet Connector
121
Ω
termination resistance
②
When using TAP-CP01 to establish a DeviceNet network, the thin cable cannot be longer than 6m.
To connect to the DeviceNet network, use the connector enclosed with TAP-CP01 or any connectors you can
buy in the store for wiring.
Termination resistance setup switch
Network power supply connector
DIN rail
PIN
V-
L
Signal
V-
Description
0V DC
Unit: mm [inch]
V+
H
CAN_L
SHIELD
CAN_H
V+
Signal-
S
L
S
Shielded cable
Signal+
ꢂ
V-
H
ꢁ Electrical Specifications
V+
24V DC
Voltage: 11 ~ 25V DC
Power Input
PIN
V+
V-
Signal
V+
Description
24V DC
Current: 7.5A max
ꢁ Environment
V-
0V DC
V+ V-
S
Operation: 0oC ~ 55oC (temperature), 50 ~ 95% (humidity), pollution degree 2
Storage: -25oC ~ 70oC (temperature), 5 ~ 95% (humidity)
S
SHIELD
Shielded cable
Operation/storage
Download from Www.Somanuals.com. All Manuals Search And Download.
|