ENGLISH
Warning
TP-PCC01 doesn’t support plug and play function. Please turn off power before plugging.
ꢀ
ꢀ
The voltage for TP-PCC01 is supplied from TP extension slot. Please ensure that plug direction is correct when connecting
TP-PCC01 to TP extension slot in case danger and damage on the device may occur.
ꢀ Introduction
Model Name Explanation
Program Copy Card
Series
ꢁ Electrical Specifications
Model Name
TP-PCC01
Item
Data Reserved Life
Writing In
/
Times for
20 years / one hundred thousand times
Operation Temperature
Weight / Dimensions
0ºC ~ 55ºC
6g / 50.85×19.8×10 mm
ꢂ Program Copy Card Functions
Compatible firmware version: TP05G/TP08G (V1.00 and above)
Using program copy card functions can copy the whole system parameters and application programs set in
one TP05G/TP08G to another TP05G/TP08G rapidly. It can save much time and manpower. The operation is
described in the following sections.
TP-PCC01 : Program Copy Card
TP
: Terminal Panel (TP05G/TP08G Series)
TPꢁTP-PCC01
(Copy TP program to TP-PCC01)
TP-PCC01ꢁTP
(Copy program in TP-PCC01 to TP)
Step
Turn the switch on the TP-PCC01 to
TPꢁTP-PCC01
Turn the switch on the TP-PCC01 to
TP-PCC01ꢁTP
1
Insert the TP-PCC01 into the extension slot of TP
Apply power to TP
Insert the TP-PCC01 into the extension slot of TP
Apply power to TP
2
3
ꢂ
If the model type of TP does not match the
model type of the program set in TP-PCC01:
ꢂ
If there is no program in TP-PCC01.
TP will display:
(TP05G program and TP08G program can’t be
compatible with each other. It means that
TP05G program can’t be opened and edited by
TP08G, and TP08G program can’t be opened
and edited by TP05G either.)
The TP-PCC01 is Empty
TP-PCC01 ꢁ TP series
is illegal
4
TP will display:
TP series and TP-PCC01 is different
Press Enter to Confirm
TP seriesꢁTP-PCC01
Press Esc to Exit
Press CLR to Erase TP-PCC01
ꢂ
Remove the program
ꢂ
If the model type of TP does not match the
model type of the program set in TP-PCC01.
TP will display:
TP will display:
TP-PCC01 will be Erased!
Press Enter to Confirm
Press ESC to Exit
TP series and TP-PCC01 is different
Please Remove the TP-PCC01
and Reboot
ꢂ
If the model type of TP and the model type of
the program set in TP-PCC01 is matched.
ꢂ
If the model type of TP and the model type of
the program set in TP-PCC01 is matched.
TP will display:
TP will display:
Press Enter to Confirm
TP seriesꢁTP-PCC01
Press Esc to Exit
Press Enter to Confirm
TP-PCC01 ꢁTP series
Press Esc to Exit
Press CLR to Erase TP-PCC01
Press <Enter> key to confirm the “writing in”
operation.
5
Press <Enter> key to confirm the “writing in”
operation.
ꢂ
When executing “writing in” operation,
ꢂ
When executing “writing in” operation,
TP will display:
TP will display:
TP series ꢁTP-PCC01
Please wait!
TP-PCC01 ꢁTP series
Please wait!
ꢂ
“Writing in” operation is completed.
ꢂ
“Writing in” operation is completed.
TP will display:
TP will display:
Please Remove the TP-PCC01 and
Reboot
Please Remove the TP-PCC01 and
Reboot
Please turn the power of TP off and remove
TP-PCC01 from TP. At this time, all TP programs
and system parameters have been copied to
TP-PCC01.
Please turn the power of TP off and remove
TP-PCC01 from TP. At this time, all programs and
system parameters stored in TP-PCC01 have
been copied to TP.
Turn the power of TP off and then remove
TP-PCC01 when the message “Please Remove
the TP-PCC01 and Reboot” displays on the
screen of TP.
Turn the power of TP off and then remove
TP-PCC01 when the message “Please Remove
the TP-PCC01 and Reboot” displays on the
screen of TP.
6
ꢃ Dimension and Installation
Note:
To avoid damage to TP-PCC01, when installing
TP-PCC01 into TP, please pay particular attention
to the installation direction of TP-PCC01 and ensure
that the side which there is a switch on it should be
up and toward the user.
Units: mm
Download from Www.Somanuals.com. All Manuals Search And Download.
|