RR30NS, RR30NFS, RR30NIS, RR30NIFS
Document # PG05-009
Revised 05/23/13 Page 1/5
Renaissance® 30” Wide
Electric Inductive Range
PLANNING
GUIDE
Model Versions
Model
warning
Configuration
Handle Type
•
•
Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
Freestanding,
(full size side panels)
Mounted on
outside of door
RR30NS[-C]*
Freestanding,
(full size side panels)
Flush handle,
integrated in door
RR30NFS[-C]*
RR30NIS[-C]*
This appliance must be installed in accordance with the
accompanying installation instructions.
Built-in/Slide-in
(3 1/4” removable side panels)
Mounted on
outside of door
Built-in/Slide-in
(3 1/4” removable side panels)
Mounted on
outside of door
available Backguards
RR30NIFS[-C]*
Part number Description
Compatibility
Optional on all models
* Order -C option for corded wiring configuration, see page 3/5 for details.
ADRB30E03
ADRB30E06
ADRB30E0
3 Inch
Standard on models RR30NS, RR30NFS
Optional on models RR30NIS, RR30NIFS
ptional on all models
Models Rme equipped from the factory with
flat staa backguard. A backguard may be
purcsory. Add an additional 1/16 inch to depth
dilling a backguard on models RR30NIS and
Product Dimensions
All tolerances ±1/16” (±1.6 mm) unless otherwise noted.
A
B
C
D
panel
ckguard thickness
�
d*
6” (15.2 cm)
backguard*
3” (7.6 cm)
backguard*
RR30NI[F]S:
3/8” (9.5 mm)
thick top trim
Dimension rr30nS, rr30nFS
rr30niS, rr30niFS
46 1/16” (117.0 cm)
25 5/16” (64.3 cm)
23 3/16” (58.9 cm)
A
C
D
46 1/4” (117.5 cm)
25 1/2” (64.8 cm)
23 3/8” (59.4 cm)
External handle
shown, some models
have integral handle
RR30N[F]S:
full stainless
steel side panels
35”
(88.9 cm)
to
37”
(94.0 cm)
Dimension
rr30nS
rr30niS
B
27 7/8” (70.8 cm)
27 11/16” (70.3 cm)
RR30NI[F]S:
3” (7.6 cm)
partial stainless
steel side panels
(removable)
The trim on models RR30NS and RR30NFS are not compatible
with a raised vent.
Models RR30NIS and RR30NIFS are compatible with Dacor
raised vent models ERV30 and ERV3015. Use only these
specified raised vent models.
Product width:
29 15/16” (76.0 cm)
*�
See table for compatibility
OvERALL DEPth DImENSIONS - SIDE vIEW
All specifications subject to change without notice.
Phone: (800) 793-0093
Download from Www.Somanuals.com. All Manuals Search And Download.
RR30NS, RR30NFS, RR30NIS, RR30NIFS
Document # PG05-009
Revised 05/23/13 Page 3/5
Renaissance 30” Wide
Electric Inductive Range
PLANNING
GUIDE
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.
■
Failure to meet or exceed the maximum and
minimum dimensions/clearances stated may result
in a fire hazard.
■
The shaded area shown denotes the location of
the electrical junction box/receptacle. This is the
suggested location. For replacement purposes, the
location of the existing electrical supply may be
utilized provided that it does not interfere with the
sides or rear of the range.
B
■
■
Access to the remote circuit breaker panel/fuse box,
with the range in place and operating, must also be
allowed for in the installation.
The electrical junction box/receptacle must be
ocated so that it does not interfere with the range
n it is installed and under operation. In addition,
ction box/receptacle must be located so
can be removed for service and remain
o power.
13” (33.0 cm)
max.4
Non-combustible
surface along
back wall
recommended
the risk of burns or fire by reaching
ed surface units, cabinet storage space
above surface units should be avoided. If
net storage space is to be provided directly
bove the range, the risk of personal injury may be
reduced by installing a range hood.
Top of
finished
counter
Note 1
Suggest
■
■
■
In all instances, installation of a range hood is highly
recommended. The hood should project horizontally
a minimum of five (5) inches beyond the face of
the cabinets. See the range hood specifications for
minimum clearances.
A
18” (45.7 cm)
locati
min.4
util
The range may be installed flush to the rear wall.
See diagram and notes for rear wall surface
requirements. It is not necessary to install non-
combustible materials behind the range below the
countertop height.
Note 2
Any openings in the wall behind the appliance or in
the floor underneath it must be sealed.
C
a*
B
c
30 1/16” min.
(76.4 cm)
36” (91.4 cm) recommended
30” (76.2 cm) min.
37” (94.0 cm)
max.
* See the cutout dimensions on following page for self-rimming installations.
FREEStANDING INStALLAtION cAbINEt cUtOUt DImENSIONS - mODELS RR30NS, RR30NFS, RR30NIS AND RR30NIFS
130” (76.2 cm) min. vertical clearance from top of range grates to bottom of uncovered wood or metal cabinet. 24” (61 cm) min. clearance if bottom of wood
or metal cabinets are protected by not less than 1/4“ (0.6 cm) flame retardant millboard covered with no less than No. 28 MSG sheet steel 0.015” (0.04
cm) stainless steel, or 0.024” (0.06 cm) aluminum or 0.020” (0.05cm) copper. If installing range hood, check the hood specifications for minimum required
clearances.
2Cabinet/countertop depth is at discretion of customer but cabinet face SHALL NOT protrude further than rear of front panel. See Product Dimensions.
3Consult local code and following pages for requirements.
4This specification not applicable for cabinets more than a horizontal distance of 1” (2.6 cm) min from edge of range.
51” (2.6 cm) min. to combustible sidewalls above range (both sides).
All specifications subject to change without notice.
Phone: (800) 793-0093
Download from Www.Somanuals.com. All Manuals Search And Download.
RR30NS, RR30NFS, RR30NIS, RR30NIFS
Document # PG05-009
Revised 05/23/13 Page 4/5
Renaissance 30” Wide
Electric Inductive Range
PLANNING
GUIDE
Cabinet Cutouts for Self-rimming installation (Models rr30niS and rr30niFS Only)
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.
Countertop
1 5/8 (41.1 cm)
max. thickness
Countertop height: 34 3/4” (88.3 cm) min.
36 7/8” (93.7 cm) max.
Countertop thickness: 1 5/8” (4.1 cm) max.
(see diagrams)
■
■
The self-rimming installation of the RR30NI[F]S range creates a
“built-in” look where the range trim overlaps the countertop on both
sides and in back.
iMPOrTanT: When installing the range in this configuration,
ventilation must be provided to allow for cooling of the ranges
internal components. See diagram, left.
34 3/4”
(88.3 cm)
to
36 7/8”
(93.7 cm)
■
■
Observe all vecabinet clearances on page 3/5.
Cut 3” dia. (7.6 cm) holes
at back bottom of cabinet
for ventilation.
On self-rimions when sliding the range into position, it
will stop he control panel or side panels contact the
notce countertop.
Provide ventilation through
cabient both sides,
7 square inches min.
Location may vary.
1” min. (2.6 cm)
to any combustibles
above counter both sides
Rear wall or
countertop edge
3/8” min
counte
tOP vIEW - SLIDE-IN, SELF-RImmING INStALLAtION,
3” SIDE PANELS INStALLED
0”
0.8 cm)
to
23”
(58.4 cm)
24 5/8”
(62.5 cm)
max.
29 1/4” (74.3 c
countertop op
30 1/16” (
cabinet
below
Notch co
to width of c
Cabinet fac
below counterto
Countertop front
1” min. (2.6 cm)
Rear wall or
3/8” min. (9.5 mm)
countertop overhang
to any combustibles
countertop edge
above counter both sides
tOP vIEW - SLIDE-IN, SELF-RImmING INStALLAtION,
3” SIDE PANELS REmOvED
* To create a “built-in look” on the front of the cabinet, this
dimension may be changed to 29 1/4” (74.3 cm), with the
width at the notches remaining 30 1/16”. This configuration
is only for models RR30NIS and RR30NIFS with side panels
behind door removed.
23”
(58.4 cm)
24 5/8”
(62.5 cm)
max.
29 1/4” (74.3 cm)
countertop opening
30 1/16” (76.2 cm)*
cabinet opening
below countertop
Notch countertop
to width of cabinets
Cabinet face
below countertop
Countertop front
All specifications subject to change without notice.
Phone: (800) 793-0093
Download from Www.Somanuals.com. All Manuals Search And Download.
RR30NS, RR30NFS, RR30NIS, RR30NIFS
Document # PG05-009
Revised 05/23/13 Page 5/5
Renaissance 30” Wide
Electric Inductive Range
PLANNING
GUIDE
Cabinet Cutouts for Self-rimming installation (Models rr30niS and rr30niFS Only)
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.
Countertop
1 5/8 (41.1 cm)
max. thickness
Countertop height: 34 3/4” (88.3 cm) min.
36 7/8” (93.7 cm) max.
Countertop thickness: 1 5/8” (4.1 cm) max.
(see diagrams)
■
■
Trim kit PN ATKR30SR is required for proper installation of a raised
vent with this range.
The self-rimming installation of the RR30NI[F]S range and ERV30[15]
raised vent create a “built-in” look where the range trim overlaps
the countertop on both sides and the raised vent trim overlaps the
countertop in back. The ATKR30SR trim kit, installed on the back of
the range, will cer the front of the raised vent chassis.
34 3/4”
(88.3 cm)
to
36 7/8”
(93.7 cm)
■
iMPOrTanstalling the range in this configuration,
ventilatioed to allow for cooling of the ranges
internagram, left.
Cut 3” dia. (7.6 cm) holes
at back bottom of cabinet
for ventilation.
■
■
Oarances on page 3/5.
Provide ventilation through
cabient both sides,
7 square inches min.
Location may vary.
configuration is required for raised vent
ons with a raised vent, when sliding the
will stop when the rear of the control panel or
ct the notches toward the front of the countertop.
1” min. (2.6 cm)
to any combustibles
above counter both sides
Rear wall or
countertop edge
3/8
c
(6.7 cm)
27 1/2” (69.9 cm)
raised vent opening
tOP vIEW - DOWNDRAFt ERv30[15] WIth
SLIDE-IN, SELF-RImmING INStALLAtION,
3” SIDE PANELS INStALLED
20 3/8”
(51.8 cm)
to
23 3/8”
(59.4 cm)
25”
(63.5 cm)
max.
cm)
29 1/4” (
countert
30
c
b
Notc
to width s
Cabinet
below countertop
Countertop front
1” min. (2.6 cm)
to any combustibles
above counter both sides
Rear wall or
countertop edge
3/8” min. (1.0 cm)
countertop overhang
2 5/8” (6.7 cm)
27 1/2” (69.9 cm)
raised vent opening
tOP vIEW - DOWNDRAFt ERv30[15] WIth
SLIDE-IN, SELF-RImmING INStALLAtION,
3” SIDE PANELS REmOvED
25”
(63.5 cm)
max.
23 3/8”
(59.4 cm)
29 1/4” (74.3 cm)
countertop opening
30 1/16” (76.2 cm)*
cabinet opening
below countertop
* To create a “built-in look” on the front of the cabinet, this
dimension may be changed to 29 1/4” (74.3 cm), with the
width at the notches remaining 30 1/16”. This configuration
is only for models RR30NIS and RR30NIFS with side
panels behind door removed.
Notch countertop
to width of cabinets
Cabinet face
below countertop
Countertop front
All specifications subject to change without notice.
Phone: (800) 793-0093
Download from Www.Somanuals.com. All Manuals Search And Download.
|