Model DP-301P
Multiprotocol Ethernet/Fast Ethernet
Print Server
Hardware Guide
Rev. 01 (March 1999)
6DP301P...01
Printed In Taiwan
RECYCLABLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Software:
Warranty service for software products may be obtained by contacting a D-Link office within the
applicable warranty period. A list of D-Link offices is provided at the back of this manual,
together with a copy of the Registration Card. If a Registration Card for the product in question
has not been returned to a D-Link office, then a proof of purchase (such as a copy of the dated
purchase invoice) must be provided when requesting warranty service. The term "purchase" in
this software warranty refers to the purchase transaction and resulting licence to use such
software.
D-Link warrants that its software products will perform in substantial conformance with the
applicable product documentation provided by D-Link with such software product, for a period of
ninety (90) days from the date of purchase from D-Link or its Authorized Reseller. D-Link
warrants the magnetic media, on which D-Link provides its software product, against failure
during the same warranty period. This warranty applies to purchased software, and to
replacement software provided by D-Link pursuant to this warranty, but shall not apply to any
update or replacement which may be provided for download via the Internet, or to any update
which may otherwise be provided free of charge.
D-Link's sole obligation under this software warranty shall be to replace any defective software
product with product which substantially conforms to D-Link's applicable product
documentation. Purchaser assumes responsibility for the selection of appropriate application
and system/platform software and associated reference materials. D-Link makes no warranty
that its software products will work in combination with any hardware, or any application or
system/platform software product provided by any third party, excepting only such products as
are expressly represented, in D-Link's applicable product documentation as being compatible.
D-Link's obligation under this warranty shall be a reasonable effort to provide compatibility, but
D-Link shall have no obligation to provide compatibility when there is fault in the third-party
hardware or software. D-Link makes no warranty that operation of its software products will be
uninterrupted or absolutely error-free, and no warranty that all defects in the software product,
within or without the scope of D-Link's applicable product documentation, will be corrected.
D-Link Offices for Registration and Warranty Service
The product's Registration Card, provided at the back of this manual, must be sent to a D-Link
office. To obtain an RMA number for warranty service as to a hardware product, or to obtain
warranty service as to a software product, contact the D-Link office nearest you. An addresses/
telephone/fax list of D-Link offices is provided in the back of this manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
Limitation of Warranties
IF THE D-LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE
CUSTOMER'S SOLE REMEDY SHALL BE, AT D-LINK'S OPTION, REPAIR OR
REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE
AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN
FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. D-
LINK NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION
MAINTENANCE OR USE OF D-LINK'S PRODUCTS
D-LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND
EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT
EXIST OR WAS CAUSED BY THE CUSTOMER'S OR ANY THIRD PERSON'S MISUSE,
NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO
REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY
ACCIDENT, FIRE, LIGHTNING OR OTHER HAZARD.
LIMITATION OF LIABILITY
IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF
DATA, LOSS OF PROFITS, COST OF COVER OR OTHER INCIDENTAL, CONSEQUENTIAL
OR INDIRECT DAMAGES ARISING OUT THE INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE OR INTERRUPTION OF A D- LINK PRODUCT, HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY. THIS LIMITATION WILL APPLY EVEN IF
D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
IF YOU PURCHASED A D-LINK PRODUCT IN THE UNITED STATES, SOME STATES DO
NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
Download from Www.Somanuals.com. All Manuals Search And Download.
Wichtige Sicherheitshinweise
1. Bitte lesen Sie sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den spätern Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig-
oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung.
4. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden,
die vom Hersteller zugelassen sind.
5. Das Gerät is vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sichern Stand zu achten. Ein Kippen oder Fallen
könnte Verletzungen hervorrufen. Verwenden Sie nur sichere Standorte und beachten Sie
die Aufstellhinweise des Herstellers.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor Überhitzung schützt.
Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.
9. Die Netzanschlußsteckdose muß aus Gründen der elektrischen Sicherheit einen
Schutzleiterkontakt haben.
10. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollete auch
nichts auf der Leitung abgestellt werden.
11. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten.
12. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz
trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden.
13. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät
gelangen. Dies könnte einen Brand bzw. Elektrischen Schlag auslösen.
14. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur
von authorisiertem Servicepersonal geöffnet werden.
15. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer
qualifizierten Servicestelle zu überprüfen:
a – Netzkabel oder Netzstecker sint beschädigt.
b – Flüssigkeit ist in das Gerät eingedrungen.
c – Das Gerät war Feuchtigkeit ausgesetzt.
d – Wenn das Gerät nicht der Bedienungsanleitung ensprechend funktioniert oder Sie mit
Hilfe dieser Anleitung keine Verbesserung erzielen.
e – Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f – Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
16. Bei Reparaturen dürfen nur Orginalersatzteile bzw. den Orginalteilen entsprechende Teile
verwendet werden. Der Einsatz von ungeeigneten Ersatzteilen kann eine weitere
Beschädigung hervorrufen.
17. Wenden Sie sich mit allen Fragen die Service und Repartur betreffen an Ihren
Servicepartner. Somit stellen Sie die Betriebssicherheit des Gerätes sicher.
Download from Www.Somanuals.com. All Manuals Search And Download.
Trademarks
Copyright ã 1997 D-Link Corporation.
Contents subject to change without prior notice.
D-Link is a registered trademark of D-Link Corporation/D-Link
Systems, Inc.
All other trademarks belong to their respective proprietors.
Copyright Statement
No part of this publication may be reproduced in any form or by
any means or used to make any derivative such as translation,
transformation, or adaptation without permission from D-Link
Corporation/D-Link Systems Inc., as stipulated by the United
States Copyright Act of 1976.
FCC Warning
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with this user’s guide, may cause harmful interference
to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product
may cause radio interference in which case the user may be
required to take adequate measures.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
0 ABOUT THIS GUIDE ...............................................................................2
1 INTRODUCTION ......................................................................................3
PRODUCT CAPABILITIES ................................................................................3
EXTERNAL FEATURES ...................................................................................4
Front .........................................................................................................5
Back ..........................................................................................................6
2 UNPACKING AND INSTALLATION.....................................................8
UNPACKING AND INSPECTION .......................................................................8
INSTALLING THE DP-301P ............................................................................9
POWER-UP AND SELF-TEST..........................................................................10
Indicator Test..........................................................................................10
Circuit Tests ............................................................................................10
Operational Test .....................................................................................11
3 PRODUCT SPECIFICATIONS..............................................................12
4 PORT PINOUTS ......................................................................................14
5 INDEX.......................................................................................................17
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-301P Print Server Hardware Guide
0 ABOUT THIS GUIDE
This guide describes the D-Link DP-301P Multiprotocol
Ethernet/Fast Ethernet Print Server. DP-301P features,
installation procedures, and troubleshooting methods are
explained in detail.
The software and related documentation included with your
DP-301P are important parts of the DP-301P package. For
information on installing and using the included software, see the
PS Admin User’s Guide.
2
About this Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-301P Print Server Hardware Guide
1
1 INTRODUCTION
The DP-301P is a pocket-sized device for connecting a printer
directly to an Ethernet or Fast Ethernet local-area network (LAN).
The DP-301P will manage the flow of data from networked
computers to the connected printer, delivering jobs to the printer
much faster than a computer acting as a file server or print server
can.
Product Capabilities
The DP-301P improves network printing services in three ways:
¨
The DP-301P picks up the workload of managing print file
traffic to the connected printer. This provides workload relief to
your file servers, and allows the file servers' full capacity to be
used for file access and other direct services to network users.
On peer-to-peer networks, workstations can print directly to the
DP-301P without increasing the load of another workstation or
server.
¨
¨
The DP-301P's IEEE 1284-compliant high-speed bi-directional
parallel printer port can transmit data much faster than a
computer's parallel printer port can. A high-speed laser printer
can be driven at its full capacity.
Because the DP-301P is very portable (pocket-sized) and
inexpensive compared to a computer-based print server, and
Introduction
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-301P Print Server Hardware Guide
because the DP-301P connects to your file servers through the
network, the printer can be stationed at the location of
maximum convenience to users.
The DP-301P offers extraordinary flexibility, and works with all
major network operating systems and protocols:
¨
IP X/SP X
Novell NetWare 3.x and 4.x (using either bindery emulation or
native NDS)
¨
TCP /IP
Unix lpr/lpd (HP-UX, SunOS, Solaris, SCO, UnixWare, IBM
AIX), Windows NT
¨
¨
NetBEUI
Windows NT, Windows 95, Windows for Workgroups, Microsoft
LAN Manager, IBM LAN Server
Ap p leTa lk
MacOS EtherTalk
Your DP-301P package includes PS Admin, a Windows-based setup
and administration program, which makes configuration and
management of your D-Link print servers quick and easy. The
DP-301P also has a Telnet interface for management
communications. If Windows is not available on the station you
choose for print server administration, then all configuration and
management commands can be issued to the DP-301P, and all
console messages and management report information will be
returned, via Telnet.
External Features
This section describes the visible parts of the DP-301P print server.
4
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-301P Print Server Hardware Guide
Front
The panel on which the DP-301P’s network port, DC power jack,
and light-emitting diode (LED) indicators appear is referred to in
this guide as the device’s “front” section.
Network Port
DC Power
Input
Led Indicators
DP-301P Front Section
Network Port
The network port, an RJ -45 jack in the middle of the DP-301P’s
front section, provides for connection to the network through an
appropriate twisted-pair cable (Category 3 or higher for 10Base-T
Ethernet, Category 5 or higher for 100Base-TX Fast Ethernet).
DC Power Jack
The DC power jack is designed for a 5V/1.5A power supply. The
power adapter included in your DP-301P package is correct for the
DP-301P. Substitution of other equipment may void warranty.
Introduction
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-301P Print Server Hardware Guide
Indicators
The DP-301P’s front panel includes three indicator lights. See
"Power-up and Self-Test," Chapter 2, for a description of indicator
behavior upon device startup. During operation following a normal
startup, the indicators provide the following status signals:
¨
P w /Tx
Steady or flashing green confirms power on.
This indicator blinks (goes off briefly) when the DP-301P is
transmitting to the network.
¨
Lk /Rx
Steady or flashing green confirms that the DP-301P has a good
connection to the network.
This indicator blinks (goes off briefly) when the DP-301P is
receiving from the network.
¨
LP T
This indicator shows steady green whenever the DP-301P is
transferring print data through its printer port.
Back
The “back” section of the DP-301P consists entirely of the device’s
printer port.
DP-301P Back End
6
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-301P Print Server Hardware Guide
Printer Port
The printer port can be configured using the PS Admin program,
or by commands issued to the DP-301P via Telnet. See the PS
Admin User’s Guide for configuration procedures.
Introduction
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2
2 UNPACKING AND
INSTALLATION
This chapter explains how to install your DP-301P print server and
connect it to the network. It also describes the automatic power-on
self-test.
Unpacking and Inspection
Carefully remove all items from the package. In addition to this
Hardware Guide, be certain that you have:
¨
¨
¨
¨
¨
¨
One DP-301P print server
One AC power adapter suitable for AC power in your area
Two PS Admin for Windows software diskettes
One PS Admin User’s Guide
One lpr software diskette
One lpr user's guide
If any item is missing, or if you find any damage or mismatch,
promptly contact your dealer for assistance.
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-301P Print Server Hardware Guide
Installing the DP-301P
Follow these steps for a trouble-free start of print-server operations
with your DP-301P. Please take particular notice of the warning in
step 4: the network connection should be made before supplying
power to the DP-301P.
1. Confirm proper operation of the printer to be connected to the
DP-301P.
2. When you have confirmed proper operation of the printer,
switch its power off.
3. Confirm that your network is operating normally.
4. Connect the DP-301P to the network through the RJ -45 jack on
the print server’s front panel.
WARNING: Configuration problems may result if the DP-301P is
powered up without first establishing its network
connection. Follow this procedure to avoid
complications at the configuration stage.
5. While the printer is off, connect the DP-301P print server
directly to the printer’s parallel port.
6. Switch printer power on.
7. Plug the AC power adapter’s output plug into the DP-301P’s DC
power input jack.
8. Plug the AC power adapter into an AC power outlet. This will
supply power to the DP-301P. (The DP-301P has no power
switch.) The DP-301P’s self-test routines will proceed
automatically.
Unpacking and Installation
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-301P Print Server Hardware Guide
Power-up and Self-test
Whenever the DP-301P is powered up, two testing procedures
follow automatically. The first procedure is a programmed series of
flashes intended to confirm proper operation of the three LED
indicators. The second procedure comprises programmed tests of
the DP-301P’s internal circuitry. If any fault is found during the
circuitry tests, testing stops and a continuous pattern of flashes
signals the nature of the fault.
Indicator Test
Immediately upon power-up, all three indicators will show steady
green for several seconds. Then the LPT indicator will flash three
times while the Pw/Tx and Lk/Rx indicators remain steady.
Irregularity of any indicator during this test indicates that there is
a problem with the indicators themselves. Contact your dealer for
correction of any indicator problems before proceeding.
Circuit Tests
The circuit tests immediately follow the indicator test. A normal
(no fault) result is signaled by three flashes of the LPT indicator
and the start of normal print server operation.
If any error condition is found during the circuit tests, testing will
halt with the LPT indicator continuously signaling the particular
error according to the following table.
10
Unpacking and Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-301P Print Server Hardware Guide
LPT Indicator Flash Pattern
steady long flashes
Error Type
Firmware Reload Required
DRAM Error
continuously on
One long, two short flashes
One long, three short flashes
One long, four short flashes
One long, five short flashes
One long, six short flashes
One long, seven short flashes
One long, eight short flashes
One long, nine short flashes
steady short flashes
Timer INT Error
Flash Protected
Flash ID Error
Flash Erase / Program Error
LAN Controller Error
LAN Memory Error
Parallel Controller Error
LPT Error
EEPROM Error
One long, eleven short flashes
LAN I/O Base error
In the event of a Firmware Reload Required error at startup,
proceed according to instructions given in the PS Admin User’s
Guide ("PS Admin Administration" section, under the heading
"Upgrading the Print Server's Internal Firmware").
In the event that any of the other listed error conditions is
encountered on startup, contact your dealer for correction of the
fault.
Operational Test
The PS Admin software includes a Print Test function for
confirmation of print server connections and functions. This
operational test can be performed after you have installed the PS
Admin software and completed the PS Admin procedures for
configuring the DP-301P. See the instructions given in the PS
Admin User’s Guide ("Getting Started Setting up Your Print
Server" section, under the heading "Testing your Print Server").
Unpacking and Installation
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-301P Print Server Hardware Guide
A
3 PRODUCT
SPECIFICATIONS
Printer Connection
P r in ter P or t: IEEE 1284 standard bidirectional parallel interface
with 36-pin connector.
Bid ir ection a l Com m u n ica tion : Hewlett-Packard PJ L (Printer
J ob Language) standard for bidirectional communication.
Network Connection
Netw or k Sta n d a r d s: IEEE 802.3 10Base-T Ethernet and IEEE
802.3u 100Base-TX Fast Ethernet.
Netw or k Da ta Tr a n sfer Ra te: 10 or 100 megabits per second
(auto-detecting)
Netw or k Con n ector : RJ -45 connector for 10Base-T or
100Base-TX twisted-pair connection.
Network Protocols
Eth er n et F r a m e Typ es: 802.2, 802.3, Ethernet II, SNAP (auto-
switching)
Tr a n sp or t P r otocols: IPX/SPX, TCP/IP NetBEUI,
AppleTalk/EtherTalk
12
Product Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-301P Print Server Hardware Guide
TCP /IP P r otocols Su p p or ted : BOOTP, SNMP, Telnet, TFTP,
FTP, lpd, RARP, DHCP
Management and Diagnostics
Sta n d a r d : SNMP
MIBs: MIB-II (RFC 1213)
Dia gn ostic LED In d ica tor s: Pw/Tx, Lk/Rx, LPT
Environmental and Physical
P ow er Su p p ly: External AC power adapter providing 5V/1.5A
DC power
Dim en sion s: 92.8mm ´ 58mm ´ 25.3mm
Weigh t: approx. 65g
Op er a tin g Tem p er a tu r e: 0 to 50°C
Stor a ge Tem p er a tu r e: -25 to 55°C
Hu m id ity: 5% to 95% non-condensing
E m ission s: FCC Class A, CISPR 22 Class A, VCCI Class 1,
AS/NZS 3548:1995 Class A
Sa fety: UL (UL 1950), CSA (CSA950), TÜV/GS (EN60950)
Product Specifications
13
Download from Www.Somanuals.com. All Manuals Search And Download.
B
4 PORT PINOUTS
The following table lists the pinouts of the DP-301P’s 36-pin
parallel port connector (identical to the parallel port connector
used on most printers.)
Signal names beginning with n are active-low signals.
Pin #
1
2
3
4
5
6
7
8
Signal
nStrobe
Data 1 §
Data 2
Data 3
Data 4
Source
H
Bi-Diª
Bi-Diª
Bi-Diª
Bi-Diª
Bi-Diª
Bi-Diª
Bi-Diª
Bi-Diª
P
Data 5
Data 6
Data 7
9
Data 8¨
nAck
10
11
12
13
14
15
16
17
Busy
PError
Select
P
P
P
H
nAutoFd
Not Defined
Logic Gnd
Chassis Gnd
§
ª
Least Significant Bit
Data signals will be driven by some , but not all peripheral devices.
¨ Most Significant Bit
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-301P Print Server Hardware Guide
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Peripheral Logic High
P
Signal Ground (nStrobe)
Signal Ground (Data 1)
Signal Ground (Data 2)
Signal Ground (Data 3)
Signal Ground (Data 4)
Signal Ground (Data 5)
Signal Ground (Data 6)
Signal Ground (Data 7)
Signal Ground (Data 8)
Signal Ground (PError, Select, nAck)
Signal Ground (Busy, nFault)
Signal Ground (nAutoFd, nSelectIn, nInit)
nInit
H
P
nFault
Not Defined
Not Defined
Not Defined
nSelectIn
H
Port Pinouts
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
5 INDEX
100Base-TX, 5, 12
10Base-T, 5, 12
AC power adapter, 5, 8, 9, 13
AppleTalk, 4, 12
automatic self test, 8
bidirectional printer port, 3, 12
cable, 5
MIB, 13
NetBEUI, 4, 12
NetWare, 4
network port, 5, 12
power adapter, 5, 8, 9, 13
power-up sequence, 9
print test, 11
DC power, 5, 9, 13
diskettes, 8
EtherTalk, 4, 12
protocols, 4, 13
PS Admin, 2, 4, 7, 8, 11
Pw/Tx indicator, 6, 10
reload, 11
file server, 3, 4
firmware, 11
IEEE 1284, 3, 12
RJ-45, 5, 9, 12
self test, 8
IEEE 802.3, 12
SNMP, 13
IEEE 802.3u, 12
IPX/SPX, 4, 12
LED (defined), 5
software diskette, 8
standards, 12, 13
startup tests, 8
Lk/Rx indicator, 6, 10
lpd network printing utility, 4, 13
lpr network printing utility, 4
LPT indicator, 6, 10, 11
TCP/IP, 4, 13
Telnet, 4, 7, 13
twisted-pair, 5, 12
Unix, 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Offices
U.S.A.
D-LINK SYSTEMS, INC.
53 Discovery Drive, Irvine, CA 92618 USA
E-MAIL: tech@dlink.com
CANADA
D-LINK CANADA, INC.
6 - 2180 Dunwin Drive, Mississauga, Ontario, Canada , L5L 5M8
E-MAIL: support@dlink.ca
sales@dlink.ca
FTP: ftp.dlinknet.com
DE NMAR K
F R ANCE
D-LINK DE NMAR K
Naverland 2 DK-2600 Glostrup Copenhagen, Denmark
TEL:45-43-969-040 FAX:45-43-424-347
D-LINK F R ANCE
Le FLORILEGE #2, Allee de la Fresnerie
78330 Fontenay Le Fleury France
GE R MANY
D-LINK (DE UTSCHLAND) GMBH I.G.
Bachstrae 22, 65830 Kriftel Germany
INFO: 0130-7250-00 (toll free) HELP: 0130-7250-40 (toll free)
ITALY
SWEDEN
U.K.
D-LINK ITALY
Via Nino Bonnet n. 6, 20154 Milano, Italy
TEL: 39-2-2900-0676 FAX: 39-2-2900-1723
D-LINK A/B
World Trade Center P. O. Box 70396, 107 24 Stockholm Sweden
TEL: 46-8-700-6211 FAX: 46-8-219-640 E-MAIL: info@dlink.se
D-LINK (EUROP E) LTD.
D-Link House, 6 Garland Road, Stanmore, London HA7 1DP U.K.
E-MAIL: info@dlink.co.uk
AUSTRALIA
CH INA
D-LINK AUSTRALIA P TY.LTD.
Unit 16, 390 Eastern Valley Way Roseville, NSW 2069 Australia
D-LINK BEIJ ING
15th Floor, Science & Technology Tower,
No. 11, Baishiqiao Road, Haidian District, Beijing 100081 China
INDIA
D-LINK (INDIA) P VT. LTD.
Bombay Office : Plot No.5, Kurla-Bandra Complex Rd.
Off Cst Rd., Santacruz (E) Bombay - 400 098 India
TEL: 91-22-6172478 FAX: 91-22-6172476
J AP AN
D-LINK TOKYO
10F, 8-8-15 Nishigotanda, Shinagawa-ku Tokyo 141 J apan
SINGAP OR E
TAIWAN
D-LINK SINGAP ORE P TE .LTD.
1 International Business Park, #03-12 The Synergy, Singapore 609917
TEL : 65-774-6233 FAX: 65-774-6322 BBS: 65-774-4787 E-MAIL: info@dlink.com.sg
D-LINK TAIWAN
2F, No. 233-2 Pao-Chiao Rd, Hsin-Tien, Taipei, Taiwan, R.O.C.
Download from Www.Somanuals.com. All Manuals Search And Download.
Registration Card
Print, type or use block letters.
Your name: Mr./Ms_____________________________________________________________________________
Organization: ________________________________________________Dept. ____________________________
Your title at organization:________________________________________________________________________
Telephone:_______________________________________ Fax:________________________________________
Organization's full address: ______________________________________________________________________
____________________________________________________________________________________________
Country: _____________________________________________________________________________________
Date of purchase (Month/Day/Year): _______________________________________________________________
Product Model
Product Serial
No.
* Product installed in type of
computer (e.g., Compaq 486)
* Product installed in
computer serial No.
(* Applies to adapters only)
Product was purchased from:
Reseller's name: ______________________________________________________________________________
Telephone:_______________________________________ Fax:________________________________________
Reseller's full address: _________________________________________________________________________
_________________________________________________________________________
_________________________________________________________________________
Answers to the following questions help us to support your product:
1. Where and how will the product primarily be used?
oHome oOffice oTravel oCompany Business oHome Business oPersonal Use
2. How many employees work at installation site?
o1 employee o2-9 o10-49 o50-99 o100-499 o500-999 o1000 or more
3. What network protocol(s) does your organization use ?
oXNS/IPX oTCP/IP oDECnet oOthers_____________________________
4. What network operating system(s) does your organization use ?
oD-Link LANsmart oNovell NetWare oNetWare Lite oSCO Unix/Xenix oPC NFS o3Com 3+Open
oBanyan Vines oDECnet Pathwork oWindows NT oWindows NTAS oWindows '95
oOthers__________________________________________
5. What network management program does your organization use ?
oD-View oHP OpenView/Windows oHP OpenView/Unix oSunNet Manager oNovell NMS
oNetView 6000 oOthers________________________________________
6. What network medium/media does your organization use ?
oFiber-optics oThick coax Ethernet oThin coax Ethernet o10BASE-T UTP/STP
o100BASE-TX o100BASE-T4 o100VGAnyLAN oOthers_________________
7. What applications are used on your network?
oDesktop publishing oSpreadsheet oWord processing oCAD/CAM
oDatabase management oAccounting oOthers_____________________
8. What category best describes your company?
oAerospace oEngineering oEducation oFinance oHospital oLegal oInsurance/Real Estate oManufacturing
oRetail/Chainstore/Wholesale oGovernment oTransportation/Utilities/Communication oVAR
oSystem house/company oOther________________________________
9. Would you recommend your D-Link product to a friend?
oYes oNo oDon't know yet
10.Your comments on this product?
__________________________________________________________________________________________
__________________________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|