CY62148BN MoBL®
4-Mbit (512K x 8) Static RAM
Functional Description
Features
• High Speed
The CY62148BN is a high-performance CMOS static RAM
organized as 512K words by 8 bits. Easy memory expansion
is provided by an active LOW Chip Enable (CE), an active
LOW Output Enable (OE), and three-state drivers. This device
has an automatic power-down feature that reduces power
consumption by more than 99% when deselected.
— 70 ns
• 4.5V–5.5V operation
• Low active power
— Typical active current: 2.5 mA @ f = 1 MHz
Writing to the device is accomplished by taking Chip Enable
(CE) and Write Enable (WE) inputs LOW. Data on the eight I/O
— Typical active current:12.5 mA @ f = f
(70 ns)
max
• Low standby current
pins (I/O through I/O ) is then written into the location
0
7
specified on the address pins (A through A ).
0
18
• Automatic power-down when deselected
• TTL-compatible inputs and outputs
Reading from the device is accomplished by taking Chip
Enable (CE) and Output Enable (OE) LOW while forcing Write
Enable (WE) HIGH for read. Under these conditions, the
contents of the memory location specified by the address pins
will appear on the I/O pins.
• Easy memory expansion with CE and OE features
• CMOS for optimum speed/power
• Available in standard lead-free and non-lead-free
32-lead (450-mil) SOIC, 32-lead TSOP II and 32-lead
Reverse TSOP II packages
The eight input/output pins (I/O through I/O ) are placed in a
0
7
high-impedance state when the device is deselected (CE
HIGH), the outputs are disabled (OE HIGH), or during a write
operation (CE LOW, and WE LOW).
Logic Block Diagram
I/O
0
INPUT BUFFER
I/O
I/O
1
2
A
0
A
1
A
4
A
5
A
6
I/O
I/O
I/O
3
4
5
512K x 8
ARRAY
A
7
A
12
A
14
A
16
A
17
I/O
6
7
POWER
DOWN
COLUMN
DECODER
CE
I/O
WE
OE
Cypress Semiconductor Corporation
Document #: 001-06517 Rev. *A
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised August 2, 2006
Download from Www.Somanuals.com. All Manuals Search And Download.
CY62148BN MoBL®
Current into Outputs (LOW)......................................... 20 mA
Maximum Ratings
Static Discharge Voltage...............................................2001V
(per MIL-STD-883, Method 3015)
(Above which the useful life may be impaired. For user guide-
lines, not tested.)
Latch-Up Current.....................................................>200 mA
Storage Temperature .................................–65°C to +150°C
Ambient Temperature with
Power Applied.............................................–55°C to +125°C
Operating Range
Ambient
Supply Voltage on V to Relative GND........ –0.5V to +7.0V
CC
[3]
Range
Commercial
Industrial
Temperature
0°C to +70°C
–40°C to +85°C
V
CC
DC Voltage Applied to Outputs
4.5V–5.5V
[2]
in High Z State .....................................–0.5V to V +0.5V
CC
[2]
DC Input Voltage ..................................–0.5V to V +0.5V
CC
Electrical Characteristics Over the Operating Range
CY62148BN-70
[1]
Parameter
Description
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Test Conditions
= Min., I = – 1 mA
Min.
Typ.
Max.
Unit
V
V
V
V
I
V
V
2.4
V
V
OH
OL
IH
CC
OH
= Min., I = 2.1 mA
0.4
CC
OL
2.2
–0.3
–1
V
+0.3
V
CC
0.8
V
IL
Input Leakage Current
Output Leakage Current
GND ≤ V ≤ V
CC
+1
+1
20
µA
µA
mA
mA
IX
I
I
I
GND ≤ V ≤ V , Output Disabled
–1
OZ
I
CC
RC
V
Operating
f = f = 1/t
MAX
Com’l/Ind’l
12.5
2.5
CC
CC
Supply Current
I
V
=0 mA
= Max.,
OUT
f = 1 MHz
Max. V ,CE ≤ V
IH
IN IH IN IL
MAX
CC
I
I
Automatic CE
Power-Down Current
—TTL Inputs
Com’l/
≤ V orV ≤ V , Ind’l
1.5
20
mA
SB1
SB2
CC
V
f = f
Automatic CE
Power-Down Current
—CMOS Inputs
Max. V
,
Com’l/
Ind’l
4
µA
CC
CE ≤ V – 0.3V,
CC
V
≤ V – 0.3V,
CC
IN
or V ≤ 0.3V, f =0
IN
Capacitance[4]
Parameter
Description
Input Capacitance
Output Capacitance
Test Conditions
Max.
Unit
pF
C
C
T = 25°C, f = 1 MHz,
6
8
IN
A
V
= 5.0V
CC
pF
OUT
AC Test Loads and Waveforms
R1 1800Ω
R1 1800Ω
5V
ALL INPUT PULSES
5V
3.0V
GND
OUTPUT
OUTPUT
R2
990Ω
90%
10%
90%
10%
R2
990Ω
100 pF
5 pF
INCLUDING
JIG AND
SCOPE
INCLUDING
JIG AND
SCOPE
≤ 3 ns
≤ 3 ns
(b)
(a)
Equivalent to:
OUTPUT
THEVENIN EQUIVALENT
639Ω
1.77V
Notes:
2. V (min.) = –2.0V for pulse durations of less than 20 ns.
IL
3. T is the “Instant On” case temperature
A
4. Tested initially and after any design or process changes that may affect these parameters.
Document #: 001-06517 Rev. *A
Page 3 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
CY62148BN MoBL®
Switching Characteristics[5] Over the Operating Range
62148BNLL-70
Parameter
Description
Min.
Max.
Unit
READ CYCLE
t
t
t
t
t
t
t
t
t
t
t
Read Cycle Time
70
10
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
RC
Address to Data Valid
70
AA
Data Hold from Address Change
CE LOW to Data Valid
OHA
ACE
DOE
LZOE
HZOE
LZCE
HZCE
PU
70
35
OE LOW to Data Valid
[6]
OE LOW to Low Z
5
10
0
[6, 7]
OE HIGH to High Z
25
25
70
[6]
CE LOW to Low Z
[6, 7]
CE HIGH to High Z
CE LOW to Power-Up
CE HIGH to Power-Down
PD
[8]
WRITE CYCLE
t
t
t
t
t
t
t
t
t
t
Write Cycle Time
70
60
60
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
WC
CE LOW to Write End
SCE
AW
Address Set-Up to Write End
Address Hold from Write End
Address Set-Up to Write Start
WE Pulse Width
HA
0
SA
55
30
0
PWE
SD
Data Set-Up to Write End
Data Hold from Write End
HD
[6]
WE HIGH to Low Z
5
LZWE
HZWE
[6, 7]
WE LOW to High Z
25
Notes:
5. Test conditions assume signal transition time of 5 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V, and output loading of the specified
/I and 100-pF load capacitance.
I
OL OH
6. At any given temperature and voltage condition, t
is less than t
, t
is less than t
, and t
is less than t
for any given device.
HZCE
LZCE HZOE
LZOE
HZWE
LZWE
7. t
, t
, and t
are specified with a load capacitance of 5 pF as in part (b) of AC Test Loads. Transition is measured ±500 mV from steady-state voltage.
HZOE HZCE
HZWE
8. The internal write time of the memory is defined by the overlap of CE LOW, and WE LOW. CE and WE must be LOW to initiate a write, and the transition of
any of these signals can terminate the write. The input data set-up and hold timing should be referenced to the leading edge of the signal that terminates the write.
Document #: 001-06517 Rev. *A
Page 4 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
CY62148BN MoBL®
Data Retention Characteristics (Over the Operating Range)
[1]
Parameter
Description
for Data Retention
CC
Conditions
Min.
Typ.
Max.
Unit
V
V
I
V
2.0
DR
Data Retention Current
Com’l LL
Ind’l LL
No input may exceed
20
20
µA
µA
ns
CCDR
V
V
+ 0.3V
CC
CC
= V = 3.0V
DR
[4]
t
t
Chip Deselect to Data Retention Time
Operation Recovery Time
CE > V – 0.3V
0
CDR
[9]
R
CC
V
V
> V – 0.3V or
IN
IN
CC
t
ns
RC
< 0.3V
Data Retention Waveform
DATA RETENTION MODE
> 2V
3.0V
3.0V
V
V
CC
DR
t
t
R
CDR
CE
Switching Waveforms
[10, 11]
Read Cycle No.1
t
RC
ADDRESS
t
AA
t
OHA
DATA OUT
PREVIOUS DATA VALID
[11, 12]
DATA VALID
Read Cycle No. 2 (OE Controlled)
ADDRESS
CE
t
RC
t
ACE
OE
t
HZOE
t
DOE
t
HZCE
t
LZOE
HIGH
IMPEDANCE
HIGH IMPEDANCE
DATA OUT
DATA VALID
t
LZCE
t
PD
t
PU
V
CC
50%
50%
SUPPLY
ISB
CURRENT
Notes:
9. Full Device operation requires linear V ramp from V to V
> 100 ms or stable at V > 100 ms.
cc(min)
CC
DR
CC(min)
10. Device is continuously selected. OE, CE = V .
IL
11. WE is HIGH for read cycle.
12. Address valid prior to or coincident with CE transition LOW.
Document #: 001-06517 Rev. *A
Page 5 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
CY62148BN MoBL®
Switching Waveforms (continued)
[13]
Write Cycle No. 1 (CE Controlled)
t
WC
ADDRESS
CE
t
SCE
t
SA
t
t
HA
AW
t
PWE
WE
t
t
HD
SD
DATA I/O
DATA VALID
[13, 14]
WC
Write Cycle No. 2 (WE Controlled, OE HIGH During Write)
t
ADDRESS
CE
t
SCE
t
HZCE
t
t
HA
AW
t
t
PWE
SA
WE
OE
t
t
SD
HD
DATA VALID
DATA I/O
IN
NOTE
15
t
HZOE
Notes:
13. If CE goes HIGH simultaneously with WE going HIGH, the output remains in a high-impedance state.
14. Data I/O is high-impedance if OE = V
.
IH
15. During this period the I/Os are in the output state and input signals should not be applied.
Document #: 001-06517 Rev. *A
Page 6 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
CY62148BN MoBL®
Switching Waveforms (continued)
[13, 14]
Write Cycle No.3 (WE Controlled, OE LOW)
t
WC
ADDRESS
CE
t
SCE
t
HZCE
t
t
HA
AW
t
SA
t
PWE
WE
t
t
HD
SD
NOTE 15
DATAI/O
DATA VALID
t
t
LZWE
HZWE
Truth Table
CE
OE
WE
I/O –I/O
Mode
Power
0
7
H
X
L
X
H
L
High Z
Power-Down
Read
Standby (I
)
SB
L
L
L
Data Out
Data In
High Z
Active (I
Active (I
Active (I
)
)
)
CC
CC
CC
X
H
Write
H
Selected, Outputs Disabled
Ordering Information
Speed
Package
Operating
Range
(ns)
Ordering Code
CY62148BNLL-70SC
CY62148BNLL-70SXC
CY62148BNLL-70ZC
CY62148BNLL-70ZXC
CY62148BNLL-70ZRC
CY62148BNLL-70SI
CY62148BNLL-70SXI
CY62148BNLL-70ZI
CY62148BNLL-70ZXI
CY62148BNLL-70ZRI
Diagram
51-85081
51-85081
51-85095
51-85095
51-85138
51-85081
51-85081
51-85095
51-85095
51-85138
Package Type
70
32-lead (450-Mil) Molded SOIC
Commercial
32-lead (450-Mil) Molded SOIC (Pb-Free)
32-lead TSOP II
32-lead TSOP II (Pb-Free)
32-lead RTSOP II
32-lead (450-Mil) Molded SOIC
32-lead (450-Mil) Molded SOIC (Pb-Free)
32-lead TSOP II
Industrial
32-lead TSOP II (Pb-Free)
32-lead RTSOP II
Please contact your local Cypress sales representative for availability of these parts
Document #: 001-06517 Rev. *A
Page 7 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
CY62148BN MoBL®
Package Diagrams
32 LD (450 Mil) SOIC32-lead (450-Mil) Molded SOIC (51-85081)
16
1
0.546[13.868]
0.566[14.376]
0.440[11.176]
0.450[11.430]
MIN.
MAX.
DIMENSIONS IN INCHES[MM]
PACKAGE WEIGHT 1.42gms
PART #
S32.45 STANDARD PKG.
SZ32.45 LEAD FREE PKG.
17
32
0.793[20.142]
0.817[20.751]
0.006[0.152]
0.012[0.304]
0.101[2.565]
0.111[2.819]
0.118[2.997]
MAX.
0.004[0.102]
0.047[1.193]
0.063[1.600]
0.004[0.102]
0.050[1.270]
BSC.
0.023[0.584]
0.039[0.990]
MIN.
0.014[0.355]
0.020[0.508]
SEATING PLANE
51-85081-*B
32-Lead
Thin Small Outline Package Type II (51-85095)
51-85095 **
Document #: 001-06517 Rev. *A
Page 8 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
CY62148BN MoBL®
Package Diagrams (continued)
32-lead Reverse Thin Small Outline Package Type II (51-85138)
51-85138-**
More Battery Life is a trademark, and MoBL is a registered trademark, of Cypress Semiconductor. All products and company
names mentioned in this document may be the trademarks of their respective holders.
Document #: 001-06517 Rev. *A
Page 9 of 10
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implDiesotwhantlothaedmfarnoumfacWturwerwa.sSsuommeasnaullarilssk.cofosmuc.hAulsleMaannduinadlsoinSgesaoricnhdeAmnndifieDsoCwypnrelosasda.gainst all charges.
CY62148BN MoBL®
Document History Page
®
Document Title: CY62148BN MoBL 4-Mbit (512K x 8) Static RAM
Document Number: 001-06517
Issue
Date
Orig. of
Change
REV.
**
ECN NO.
426504
485639
Description of Change
See ECN
See ECN
NXR
VKN
New Data Sheet
Corrected the typo in the Array size in the Logic Block Diagram
*A
Document #: 001-06517 Rev. *A
Page 10 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
|