Cuisinart Water Dispenser WCH 1500 User Manual

INSTRUCTION  
BOOKLET  
®
Cuisinart®  
WCH-1500  
Countertop Filtration System  
For your safety and continued enjoyment of this product, always read the instruction book carefully before using.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Indicator Lights  
CONTENTS  
Red/blue LEDs light up when water has  
reached hot/cold temperatures. Green LED  
lights up when unit is in "Energy Saver"  
mode (hot water is Off).  
Important Safeguards. . . . . . . . . . . . . . 2  
Special Cord Set Instructions . . . . . . . 2  
Introduction . . . . . . . . . . . . . . . . . . . . . 3  
Parts and Features. . . . . . . . . . . . . . . . 3  
Unpacking & Placement. . . . . . . . . . . . 4  
Water Filter Setup . . . . . . . . . . . . . . . . 4  
Water Dispenser Setup . . . . . . . . . . .4-5  
Operating Instructions . . . . . . . . . . . . . 5  
Replacing Water Filter . . . . . . . . . . . . . 5  
Tips and Hints . . . . . . . . . . . . . . . . . .5-6  
Cleaning and Care . . . . . . . . . . . . . . . . 6  
Troubleshooting . . . . . . . . . . . . . . . . .6-7  
Storing the Unit . . . . . . . . . . . . . . . . . . 8  
Technical Specifications . . . . . . . . . . . 8  
Performance Data Sheet . . . . . . . . . . . 9  
California Certification . . . . . . . . . . . . 10  
For Purchases Made in Iowa . . . . . . 10  
Warranty . . . . . . . . . . . . . . . . . . . . . . . 11  
10. Spigots  
11. Brushed Stainless Steel Base  
12. Internal Water Tanks (not shown)  
Hot and cold tanks – approx. ½ gallon  
total capacity.  
13. Energy Saver Switch (not shown)  
Turn off your heater when hot water is not  
needed to reduce the system's energy  
usage by more than 50%.  
14. Drainage Plugs (not shown)  
Two removable plastic plugs are located  
on bottom of unit.  
15. Replacement Water Filter  
(Model GF-80)  
The Cuisinart® water filter has an optimum  
filter life of 3 months.  
INTRODUCTION  
Pour yourself a glass of fresher, cleaner,  
filtered water for a refreshing drink without  
opening the refrigerator or a bottle.  
®
1
2
3
Your  
Countertop Filtration  
System is Cuisinart at its most convenient.  
Drink healthy!  
PARTS AND FEATURES  
4
5
1. 12-Week Filter Timer  
Lets you know when to change your  
water filter.  
6
7
8
9
10  
2. Cover  
Flip-top lid for easy filling.  
3. Upper Water Tank  
Holds approx. ½ gallon of unfiltered water.  
11  
12  
4. Lower Water Tank  
Holds approx. 1 gallon of filtered water.  
5. On/Off Power Button  
Press to power On. This will activate the  
chilling and heating functions.  
13  
6. Hot Water Button with Child Lock  
Push safety lock up, then press to dispense  
hot water.  
14  
15  
7. Room Water Button  
Press to dispense room temperature water.  
8. Cold Water Button  
Press to dispense chilled water.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Remove the filter timer from the lid by flipping  
the lid over and pressing on the plastic tab.  
UNPACKING & PLACEMENT  
®
1. Remove your Cuisinart®  
3. Wash both tanks and plastic lid in mild, soapy  
water, and rinse. Replace the filter timer.  
Countertop Filtration System carefully from  
the box.  
4. Lift the filter from the bowl and allow water to  
drain.  
2. Position the unit on a stable flat surface, close  
to a main power outlet. Avoid direct sunlight  
and keep out of the reach of children.  
NOTE: The filter's loose carbon dust may  
slightly darken water while soaking.  
3. Allow at least 3 inches of space around  
the sides and rear of the unit for proper air  
circulation.  
5. With the Cuisinart® logo  
facing up, insert the water  
filter into the upper water  
tank and push firmly into  
place.  
4. Remove filter from upper tank and carefully  
follow the SETUP instructions below. You will  
need a large bowl, a pitcher (or another type  
of container), and a glass.  
6. Place the upper tank on a  
pitcher (or another type of  
container) and fill with cold  
tap water. Allow to drain for  
5 minutes to flush out any  
remaining carbon dust, then  
pour out remaining water.  
NOTE: Do not plug in unit until ALL steps of  
SETUP are complete.  
WATER FILTER SETUP  
NOTE: For optimum filtering and flow rates,  
the water filter must be prepared and installed  
exactly as follows:  
WATER DISPENSER  
SETUP  
Preparing the Water Filter  
1. Remove the filter from its packaging.  
NOTE: Use only cold tap water to fill the unit.  
NOTE: The filter may contain a small amount  
of loose carbon dust. It may also appear moist,  
have a faint smell of plastic or a slight yellowish  
tint – these are all normal. DO  
Filling the Upper and Lower Tanks  
1. Place the upper tank onto the lower tank and  
cover with the lid.  
NOT wash filter with soap or  
Lid  
water.  
Upper  
2. Place water filter in  
water tank  
empty bowl sideways  
(see image). Pressing it  
Lower  
firmly to the bottom of the bowl, and being  
careful not to pour water directly onto the  
filter, slowly add enough cold water to fully  
submerge and cover the filter by at least 1  
inch. (You should see bubbles escaping the  
filter.)  
water tank  
2. Place assembled tanks on base. NOTE: The  
vertical groove on the upper tank must face  
the back of the unit.  
3. Continue to hold filter  
under water for at least 30  
seconds.  
3. Carefully lift the flip top lid and add cold  
water to the FILL line. NOTE: This is a gravity  
fill system. To increase the filtering flow rate,  
continue adding water to the FILL line of the  
upper tank until tanks are completely full.  
4. Release the filter and  
let it soak at least 15 minutes. NOTE:  
While soaking, the filter should be partially  
submerged and may tilt to one side.  
4. During the initial setup, allow 30–40 minutes  
for water to filter into and completely fill upper  
and lower tanks.  
Installing the Prepared Water Filter  
1. While the filter is soaking, remove the lid,  
upper water tank and lower water tank.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Filling the Internal Tanks  
NOTE: Energy Saver switch must be in the  
Upper  
Tank  
Off position for water to heat.  
NOTE: Upper and lower  
tanks must be completely  
full before proceeding.  
4. After about 1 hour and 20 minutes, the BLUE  
cold water indicator will light up, signaling  
water is chilled.  
Lower  
Tank  
1. Place a glass under the  
right spigot and press  
and continue to hold  
the COLD button until  
water flow becomes  
steady (may take up  
to 3 minutes).  
NOTE: On subsequent fill-ups, unit should take  
less than 10 minutes to heat and 30 minutes  
to chill.  
5. Press and hold each button to ensure all air  
has been purged from the unit so water flow  
is steady.  
2. Repeat process with ROOM button, and then  
with the HOT button until all flow steadily.  
Initiating Energy Saver Mode  
You can turn off the heater used to heat the  
water in the hot tank to reduce the system's  
energy usage by more than 50%. While in  
Energy Saver mode, you can still dispense water  
from your hot tank; however, it will not  
be heated.  
NOTE: When filling hot and cold internal tanks,  
the water level in the lower tank will drop and  
you will hear the filling process taking place.  
Setting the Filter Timer  
The filter timer, located on the lid of the unit, lets  
you know when to change your water filter. Each  
filter will last for 3 months.  
NOTE: We recommend you power your unit off  
when only room temperature filtered water  
is needed.  
1. Once unit is set up and all water tanks are full,  
peel off the “Filtering” sticker from the filter  
timer screen.  
1. Put the Energy Saver switch in its On position.  
2. The green LED will light up, indicating your  
unit is in Energy Saver mode.  
2. Press and hold the Start button until  
FILTERING is displayed (approx. 5 seconds).  
3. Because your unit is in Energy Saver mode  
and your hot water heater is disabled, the red  
LED hot water indicator light will turn off when  
the temperature of the hot water decreases  
(this can take up to 2 hours).  
3. In 12 weeks, the word REPLACE will appear.  
For best results, we recommend inserting a  
new Cuisinart® Water Filter immediately.  
4. You may turn off the timer and display by  
pressing the Start button for 5 seconds.  
Once you replace the filter, reset the timer by  
pressing the Start button for 3 seconds.  
4. To resume your hot water, simply put the  
Energy Saver switch in its Off position. After  
about 15 minutes, the red LED hot water  
indicator will light up, signaling hot water is  
ready to dispense.  
NOTE: You may reset the timer at any time by  
pressing and holding the Start button for  
3 seconds.  
NOTE: If your unit has been in Energy Saver  
mode for longer than a week, we recommend  
you flush out your hot water tank by dispensing  
and disposing of a full glass of water from the  
left spigot before enjoying your first glass of hot  
water.  
OPERATING INSTRUCTIONS  
Once set up is completed, tanks are filled and  
water is flowing steadily, your unit is ready to use!  
1. Close the lid and plug unit into outlet.  
2. Press the On/Off power switch on the control REPLACING WATER FILTER  
panel to turn on. The BLUE light around the  
power switch indicates the unit is on and  
cooling and heating functions are activated.  
Replacement filters may be purchased at most  
your filter, follow “Water Filter Setup” on page 4.  
3. After about 15 minutes, the RED hot water  
indicator will light up, signaling hot water is  
ready to dispense.  
TIPS AND HINTS  
• Drinking 4 to 8 glasses of water each day is  
healthy! Your countertop chiller makes it easy.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Regular use of cleaner, filtered water in your  
automatic coffeemaker means less frequent  
decalcification treatments.  
CLEANING AND CARE  
CAUTION: To prevent personal injury  
or electric shock, always unplug your  
Cuisinart®  
® Countertop Filtration  
• Use filtered water in your iron to reduce  
mineral build-up.  
System from outlet before cleaning. Do not  
immerse base in water or other liquid.  
• Treat your pets to cleaner, filtered water.  
1. Turn the unit off and unplug it from outlet.  
2. Remove the filter and place it in a bowl.  
• Cleaner, filtered water makes tea and instant  
soup or coffee taste better.  
• Keeping the upper tank full helps increase  
the filtering process as well as the flow rate  
of water from spigots.  
3. Lift upper water tank and let it drain into  
lower tank, and set it aside. Then lift lower  
tank off base and empty. Careful, a full tank  
can be very heavy!  
• Proper setup of the filter (as instructed  
on page 4) will maximize the reduction of  
contaminants and optimize taste of water.  
4. Clean the water tanks and the cover with  
warm soapy water. NOTE: Remove filter  
timer before washing lid. Filter timer is not  
immersible.  
You may notice some condensation and water  
droplets on the lid and tanks of your unit.  
This is normal due to the heating and cooling  
system.  
5. The base is not immersible. Simply wipe it  
clean with a damp cloth.  
6. Dry thoroughly when clean.  
TROUBLESHOOTING  
Symptom  
Possible Cause  
Solution  
On/Off Power but-  
ton does not light  
up.  
Unit might not be plugged  
into outlet.  
Check the wall outlet for power. Make sure the  
outlet is not controlled by a wall switch.  
It takes longer than  
45 minutes for  
the water to pass  
through the filter.  
Place filter in an empty bowl, then fill with  
water, making sure it is fully submerged.  
Resoak it for 10–15 minutes, or until no  
more bubbles are observed.  
Some air is still in the filter.  
Review “Filling the Internal Tanks” on page 5  
to be sure it was done correctly. Make sure the  
lower water tank is full. Continue to press and  
hold push buttons until water flow is steady. If  
unit still won’t dispense water or flow does not  
become steady, contact Customer Service.  
Unit does not dis-  
pense water when  
buttons are pushed.  
Internal water tanks are  
not completely filled with  
water.  
Water continues  
flowing from spigot  
after push button is  
released.  
Remove water tanks from the base. Continue  
pressing button until it no longer sticks.  
Push button is stuck.  
1. Make sure unit is plugged into outlet.  
2. Make sure air has been purged from  
internal tanks, as stated on page 5.  
3. If there is water in the tanks, it will take  
about 10 minutes for the water to heat.  
1. Power is not on.  
2. There is no water in  
tanks.  
HOT water LED  
does not light up.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
Symptom  
Possible Cause  
Solution  
1. Make sure unit is plugged into outlet.  
2. Make sure air has been purged from inter-  
nal tanks, as stated on page 5.  
3. If there is water in the tanks, it will take  
about 80 minutes for the water to chill the  
first time. It takes only about 30 minutes for  
subsequent fill-ups.  
1. Power is not on.  
2. There is no water in  
tanks.  
COLD water LED  
does not light up.  
COLD water LED  
light turns off even  
though cold water is  
not dispensed.  
Large amount of room  
temperature water was  
dispensed.  
Allow up to 30 minutes for water to chill and  
LED light will turn on.  
Energy Saver mode  
LED does not light  
up.  
1. Power is not on.  
2. Energy Saver is in Off  
position  
1. Make sure unit is plugged into outlet.  
2. Make sure Energy Saver switch is in its On  
position.  
Heater is still work-  
ing and hot water  
is still available in  
Energy Saver mode.  
Contact Customer Service.  
Filter timer does not  
show “Filtering” or  
“Replace.”  
Contact Customer Service for replacement  
filter timer.  
Battery is dead.  
1. Water tanks are not  
properly seated on  
base.  
2. Drainage plugs are not  
fully engaged.  
1. Make sure water tanks are seated  
properly on the base.  
2. Ensure that drainage plugs are correctly  
installed on the bottom of the base.  
Leakage on the  
countertop.  
Water leaks from the  
top cover.  
Drain excess water from tanks by pressing  
push buttons.  
Water tanks are overfilled.  
ROOM temperature  
water is warm.  
Allow up to 30 minutes for cold water to chill  
and blue LED light to turn on.  
HOT temperature  
water is not hot.  
Energy Saver is in On  
position.  
Make sure Energy Saver is in its Off position.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bottom of unit  
STORING THE UNIT  
1. Turn the unit off and unplug it from outlet.  
2. Remove empty water tanks, filter and cover.  
3. Allow hot water to cool, then bring base to sink.  
Drainage  
Plugs  
4. Drain internal reservoir by tilting unit slightly and removing the  
2 plastic drainage plugs from bottom of unit. Plugs are tightly  
inserted and must be gently, but firmly, worked to remove.  
5. When water has completely drained, replace plugs, tanks,  
filter and cover.  
6. Your Cuisinart®  
® Countertop Filtration System is ready to store.  
TECHNICAL SPECIFICATIONS  
®
Unit: WCH-1500  
1 Cuisinart®  
Countertop Filtration System  
1 Cuisinart® Water Filter  
System Capacity  
up to 3 months/ 48 gallons/ 181 liters  
104°F (40°C)  
Maximum Input Temperature  
Minimum Input Temperature  
Maximum Output Temperature  
Minimum Output Temperature  
Rated Service Flow  
34°F (1°C)  
194°F (90°C)  
44°F (7°C)  
6 gallons / 22.7 liters per day  
(may vary according to water conditions)  
Electrical Requirements  
AC~120V 60Hz 3.7A 450W  
System Tested and Certified by WQA against NSF/ANSI Standard 53  
for the reduction of Lead, Benzene, Cadmium, Copper, Mercury,  
Tetrachloroethylene, Toluene, and Standard 42 for the reduction of  
Chlorine Taste and Odor.  
See Performance Data Sheet for specific test conditions and results.  
Claims are calculated based on WQA accepted practice of average percent reduction. The  
contaminants or other substances removed or reduced by this water treatment device are not  
necessarily in all users’ water. Do not use with water that is microbiologically unsafe or of  
unknown quality without adequate disinfection before or after the system. Individuals requiring  
water of specific microbiological purity should consult their physician.  
The Cuisinart®  
® Countertop Filtration System processes approximately 48 gallons/  
181 liters. When the Cuisinart® Water Filter (GF-80) exceeds filtering capacity, replacement is  
essential for the product to perform as represented. In the United States, replacement filters cost  
generally $19.99 per filter. Replacement filters may be purchased at most retail outlets. The  
performance of the filter may vary based on local water conditions.  
Hot water should not be used with the Cuisinart® Water Filter (GF-80) as it will affect the filter’s  
performance.  
Refer to the Operating Instructions and Cleaning and Care for general unit operation and  
maintenance requirements. Testing was performed under standard laboratory conditions;  
actual performance may vary.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PERFORMANCE DATA SHEET  
PERFORMANCE DATA SHEET FOR MODELS WCH-1000 AND WCH-1500  
CONTAMINANT REMOVAL DATA IMPORTANT NOTICE:  
Read this Performance Data Sheet and compare the capabilities of this unit with your actual  
water treatment needs. It is recommended that, before purchasing a water treatment unit, you  
have your water supply tested to determine your actual water treatment needs.  
Performance testing conducted by WQA. These systems have been tested according to NSF/  
ANSI Standard 53 and 42 for reduction of the substances listed below. The concentration of the  
indicated substances in water entering the system was reduced to a concentration less than or  
equal to the permissible limit for the water leaving the system, as specified in NSF/ANSI Standard  
53 and Standard 42.  
Testing was performed under standard laboratory conditions; actual performance may vary.  
Removal  
Removal  
Action Level  
Hardness  
Temp  
Inlet  
Max.  
Influent  
Challenge  
Concentration  
(mg/L)  
Filter  
Effluent  
Max.  
Influent  
Water Avg.  
(mg/L)  
Percent  
Reduction  
(%)  
Permissible  
Product Water  
Concentration  
(mg/L)  
Testing  
Compart.  
(°C)  
CaCO3  
(mg/L)  
Reduction  
Requirement  
Substance  
PH  
(mg/L)  
NSF/ANSI Standard 42-Aesthetic Effects  
Chlorine Taste and  
Odor Reduction  
2.0  
2.0+/-10%  
N/A  
97.5%  
N.A.  
N.A.  
20  
7.53  
>50  
NSF/ANSI Standard 53-Health Effects  
Copper pH 6.5  
Copper pH 8.5  
Mercury pH 6.5  
Mercury pH 8.5  
3.15  
3.10  
.006  
.006  
3.0+/-10%  
3.0+/-10%  
.87  
1.0  
85.0%  
85.4%  
92.8%  
89.9%  
1.3  
1.3  
16  
120  
22  
20  
19  
19  
20  
6.42  
8.42  
6.45  
8.55  
N/A  
N/A  
N/A  
N/A  
0.006+/-10%  
0.006+/-10%  
.0009  
.001  
0.002  
0.002  
140  
Cadmium pH 6.5  
.029  
0.03+/-10%  
.002  
96.6%  
0.005  
18  
20  
6.59  
N/A  
Cadmium pH 8.5  
Benzene  
.03  
.015  
2.9  
0.03+/-10%  
0.015+/-10%  
3.0+/-10%  
.004  
.003  
.770  
92.5%  
84.1%  
89.8%  
0.005  
0.005  
1
120  
130  
320  
20  
20  
20  
8.44  
7.58  
7.54  
N/A  
N/A  
N/A  
Toluene  
Tetrachloroethylene  
Lead pH 8.5  
.014  
.149  
.154  
0.015+/-10%  
.15+/-10%  
.15+/-10%  
.003  
.007  
.004  
92.5%  
95.4%  
98.7%  
0.005  
.010  
.010  
340  
98  
21  
21  
19  
7.56  
8.5  
N/A  
N/A  
N/A  
Lead pH 6.5  
18  
6.5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PURCHASES MADE IN IOWA  
For purchases made in Iowa:  
This form must be signed and dated by the buyer and seller prior to consummation of this sale.  
This form should be retained on file by the seller for a minimum of two years.  
BUYER:  
SELLER:  
Name  
Name  
Address  
City  
Address  
City  
State  
Zip  
State  
Zip  
Signature  
Date  
Signature  
Date  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This warranty expressly excludes any defects or  
damages caused by accessories, replacement  
parts, or repair service other than those that have  
been authorized by Cuisinart.  
WARRANTY  
LIMITED THREE-YEAR WARRANTY  
This warranty is available to consumers only.  
You are a consumer if you own a Cuisinart®  
Countertop Filtration System that was  
This warranty does not cover any damage caused  
by accident, misuse, shipment or other ordinary  
household use.  
purchased at retail for personal, family or household  
use. Except as otherwise required under applicable  
law, this warranty is not available to retailers or other  
commercial purchasers or owners.  
This warranty excludes all incidental or  
consequential damages. Some states do not allow  
the exclusion or limitation of these damages, so  
these exclusions may not apply to you.  
We warrant that your Cuisinart®  
CALIFORNIA RESIDENTS ONLY  
Countertop Filtration System will be free of defects  
in materials and workmanship under normal home  
use for 3 years from the date of original purchase.  
California law provides that for In-Warranty Service,  
California residents have the option of returning a  
nonconforming product (A) to the store where it was  
purchased or (B) to another retail store which sells  
Cuisinart® products of the same type.  
We suggest you complete and return the enclosed  
product registration card promptly to facilitate  
verification of the date of original purchase.  
However, return of the product registration card  
does not eliminate the need for the consumer to  
maintain the original proof of purchase in order to  
obtain the warranty benefits. In the event that you  
do not have proof of purchase date, the purchase  
date for purposes of this warranty will be the date of  
manufacture.  
The retail store shall then, at its discretion, either  
repair the product, refer the consumer to an  
independent repair facility, replace the product, or  
refund the purchase price less the amount directly  
attributable to the consumer’s prior usage of the  
product. If the above two options do not result in  
the appropriate relief to the consumer, the consumer  
may then take the product to an independent repair  
facility if service or repair can be economically  
accomplished. Cuisinart and not the consumer  
will be responsible for the reasonable cost of  
such service, repair, replacement, or refund for  
nonconforming products under warranty.  
If your Cuisinart®  
Countertop Filtration  
System should prove to be defective within the  
warranty period, we will repair it, or if we think  
necessary, replace it.  
To obtain warranty service, simply call our toll-free  
number 1-800-726-0190 for additional information  
from our Customer Service Representatives, or send  
the defective product to Customer Service at:  
California residents may also, according to their  
preference, return nonconforming products directly  
to Cuisinart for repair, or if necessary, replacement,  
by calling our Consumer Service Center toll-free at  
1-800-726-0190.  
Cuisinart  
150 Milford Road  
East Windsor, NJ 08520.  
Cuisinart will be responsible for the cost of the  
repair, replacement, and shipping and handling for  
such products under warranty.  
BEFORE RETURNING YOUR CUISINART®  
PRODUCT  
To facilitate the speed and accuracy of your return,  
please enclose $10.00 for shipping and handling of  
the product.  
Please pay by check or money order (California  
residents need only supply proof of purchase  
and should call 1-800-726-0190 for shipping  
instructions).  
If you are experiencing problems with your  
Cuisinart® product, we suggest that you call our  
Cuisinart® Service Center at 1-800-726-0190  
before returning the product to be serviced. If  
servicing is needed, a Representative can confirm  
whether the product is under warranty and direct  
you to the nearest service location.  
NOTE: For added protection and secure handling  
of any Cuisinart® product that is being returned, we  
recommend you use a traceable, insured delivery  
service. Cuisinart cannot be held responsible for  
in-transit damage or for packages that are not  
delivered to us. Lost and/or damaged products  
are not covered under warranty. Please be sure to  
include your return address, daytime phone number,  
description of the product defect, product model  
number (located on bottom of product), original date  
of purchase, and any other information pertinent to  
the product’s return.  
Important: If the nonconforming product is to be  
serviced by someone other than Cuisinart’s  
Authorized Service Center, please remind the  
servicer to call our Consumer Service Center at  
1-800-726-0190 to ensure that the problem is  
properly diagnosed, the product is serviced with  
the correct parts, and the product is still under  
warranty.  
Your Cuisinart®  
Countertop Filtration  
System has been manufactured to the strictest  
specifications and has been designed for use with  
the authorized accessories and replacement parts.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Coffeemakers  
Food  
Processors  
Toasters  
Rice Cookers  
Cookware  
Grills  
Cuisinart offers an extensive assortment of top quality products to make life in the  
kitchen easier than ever. Try some of our other countertop appliances and  
cookware, and Savor the Good Life®.  
©ꢀ00ꢇ Conair Corporation  
Cuisinart® is a registered  
trademark of the  
Conair Corporation  
Cuisinart  
1ꢃ0 Milford Road  
East Windsor, NJ 0ꢆꢃꢀ0  
1-ꢆ00-ꢅꢀꢄ-01ꢇ0  
Printed in China  
Any trademarks or service marks of third parties  
referred to herein are the trademarks or service  
marks of their respective owners.  
0ꢇCE1ꢁꢇꢁꢂ  
IB-8896A  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Continental Platinum Slow Cooker CP43729 User Manual
Corinex Global Network Router Powerline Router User Manual
Costar Carbon Monoxide Alarm 12SIR User Manual
Craftsman Snow Blower 24788854 User Manual
Cypress Clock CY25822 2 User Manual
Desa Staple Gun 34310 User Manual
Dixon Lawn Mower 966 004201 User Manual
Fortinet Network Card ASM FX2 User Manual
FujiFilm Digital Camera 420 User Manual
FUNAI VCR 31B 254 User Manual