Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Op e r a t O r ’s Ma n u a l
Single-Stage Snow Thrower — Model 221 HP
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
Form No. 769-07046
(April 28, 2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safe Operation Practices
2
WARNING! This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
CALIFORNIA PROPOSITION 65
WARNING! Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.
DANGER: This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating fingers, hands,
toes and feet and throwing foreign objects. Failure to observe the following safety
instructions could result in serious injury or death.
Training
Preparation
1.
Read, understand, and follow all instructions on the
Thoroughly inspect the area where the equipment is to be used.
Remove all doormats, newspapers, sleds, boards, wires and other
foreign objects, which could be tripped over or thrown by the
auger/impeller.
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
1.
Always wear safety glasses or eye shields during operation
and while performing an adjustment or repair to protect
your eyes. Thrown objects which ricochet can cause serious
injury to the eyes.
2.
Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.
3.
Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and be trained and supervised by an
adult.
2.
Do not operate without wearing adequate winter outer
garments. Do not wear jewelry, long scarves or other loose
clothing, which could become entangled in moving parts.
Wear footwear which will improve footing on slippery
surfaces.
4.
5.
Never allow adults to operate this machine without proper
instruction.
3.
Use a grounded three-wire extension cord and receptacle
for all machines with electric start engines.
Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
4.
5.
Disengage all control levers before starting the engine.
Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual.
6.
7.
Keep bystanders, pets and children at least 75 feet from the
machine while it is in operation. Stop machine if anyone
enters the area.
6.
Let engine and machine adjust to outdoor temperature
before starting to clear snow.
Exercise caution to avoid slipping or falling, especially
when operating in reverse.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless
and deadly gas.
Safe Handling of Gasoline
To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
6.
7.
Do not operate machine while under the influence of
alcohol or drugs.
Muffler and engine become hot and can cause a burn. Do
not touch. Keep children away.
a. Use only an approved gasoline container.
8.
9.
Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
b. Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
Exercise caution when changing direction and while
operating on slopes. Do not operate on steep slopes.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine is
hot or running.
10. Plan your snow-throwing pattern to avoid discharge
towards windows, walls, cars etc. Thus, avoiding possible
property damage or personal injury caused by a ricochet.
e. Allow engine to cool at least two minutes before
refueling.
11. Never direct discharge at children, bystanders and pets or
f.
Never over fill fuel tank. Fill tank to no more than ½
inch below bottom of filler neck to provide space for
fuel expansion.
allow anyone in front of the machine.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
g. Replace gasoline cap and tighten securely.
13. Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
h. If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area. Wait 5
minutes before starting the engine.
14. Disengage power to the auger/impeller when transporting
i.
Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
(e.g. furnace, water heater, space heater, clothes
dryer etc.).
or not in use.
15. Never operate machine at high transport speeds on
slippery surfaces. Look down and behind and use care
when backing up.
j.
Allow machine to cool at least 5 minutes before
storing.
16. If the machine should start to vibrate abnormally, stop
the engine, disconnect the spark plug wire and ground it
against the engine. Inspect thoroughly for damage. Repair
any damage before starting and operating.
k. Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.
17. Disengage all control levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments,
or inspections.
l.
If possible, remove gas-powered equipment from
the truck or trailer and refuel it on the ground. If this
is not possible, then refuel such equipment on a
trailer with a portable container, rather than from a
gasoline dispenser nozzle.
18. Never put your hand in the discharge or collector openings.
Do not unclog chute assembly while engine is running.
Shut off engine and remain behind handles until all moving
parts have stopped before unclogging.
m. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
Operation
20. When starting engine, pull cord slowly until resistance
is felt, then pull rapidly. Rapid retraction of starter cord
(kickback) will pull hand and arm toward engine faster than
you can let go. Broken bones, fractures, bruises or sprains
could result.
1.
2.
3.
4.
Do not put hands or feet near rotating parts, in the auger/
impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
The auger/impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
21. If situations occur which are not covered in this manual, use
care and good judgment. Contact Customer Support for
assistance and the name of your nearest servicing dealer.
The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
4
se c t i O n 2 — iM p O r t a n t sa f e Op e r a t iO n pr a c t ic e s
Download from Www.Somanuals.com. All Manuals Search And Download.
14. According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years,
or 60 hours of operation. At the end of the Average Useful
Life have the machine inspected annually by an authorized
service dealer to ensure that all mechanical and safety
systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
Clearing a Clogged Discharge Chute
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with snow
throwers. Never use your hand to clean out the discharge chute.
To clear the chute:
1.
SHUT THE ENGINE OFF!
2.
Wait 10 seconds to be sure the impeller blades have
stopped rotating.
Do not modify engine
3.
Always use a clean-out tool, not your hands.
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Maintenance & Storage
1.
Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and
adjustment sections of this manual.
Notice Regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM), Oxidizing Catalyst (OC), Secondary Air
Injection (SAI) and Three Way Catalyst (TWC) if so equipped.
2.
Before cleaning, repairing, or inspecting machine
disengage all control levers and stop the engine. Wait until
the auger/impeller come to a complete stop. Disconnect
the spark plug wire and ground against the engine to
prevent unintended starting.
3.
4.
5.
Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
Spark Arrestor
WARNING! This machine is equipped with an
internal combustion engine and should not be used
on or near any unimproved forest-covered, brush
covered or grass-covered land unless the engine’s
exhaust system is equipped with a spark arrestor
meeting applicable local or state laws (if any).
Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”
If a spark arrestor is used, it should be maintained in effective
working order by the operator. In the State of California the
above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws
apply on federal lands.
A spark arrestor for the muffler is available through your
nearest engine authorized service dealer or contact the service
department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
6.
Check control levers periodically to verify they engage
and disengage properly and adjust, if necessary. Refer
to the adjustment section in this operator’s manual for
instructions.
7.
8.
9.
Maintain or replace safety and instruction labels, as
necessary.
Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
11. Always refer to the operator’s manual for proper
instructions on off-season storage.
12. Check fuel line, tank, cap, and fittings frequently for cracks
or leaks. Replace if necessary.
13. Do not crank engine with spark plug removed.
se c t i O n 2 — iM p O r t a n t sa f e Op e r a t iO n pr a c t ic e s
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the
machine before attempting to assemble and operate.
Symbol
Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before attempting to
assemble and operate
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running. There are rotating
blades inside
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running. There are rotating
blades inside
WARNING— ROTATING AUGER
Do not put hands or feet near rotating parts, in the auger/impeller housing or chute
assembly. Contact with the rotating parts can amputate hands and feet.
WARNING—THROWN OBJECTS
This machine may pick up and throw and objects which can cause serious personal injury.
WARNING—GASOLINE IS FLAMMABLE
Allow the engine to cool at least two minutes before refueling.
WARNING— CARBON MONOXIDE
Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
WARNING— ELECTRICAL SHOCK
Do not use the engine’s electric starter in the rain
WARNING— HOT SURFACE
Engine parts, especially the muffler, become extremely hot during operation. Allow engine
and muffler to cool before touching.
WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
6
se c t i O n 2 — iM p O r t a n t sa f e Op e r a t iO n pr a c t ic e s
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly & Set-Up
3
Contents of Carton
•
•
•
One Snow Thrower
•
•
One Chute Assembly
•
•
Two Ignition Keys
One 3-Prong Extension Cord
One Engine Operator’s Manual
One 20 oz. Bottle 5W-30 Oil
One Snow Thrower Operator’s Manual
2.
Pivot the upper handle into the operating position. Be sure
not to pinch any of the cables in the process. See Fig. 3-2.
NOTE: All references to the left or right side of the snow thrower
are from the operator’s position. Any exceptions will be noted.
Unpacking the Snow Thrower
1.
Open the top of the carton.
2.
Cut down the corners on the front of the carton and fold
down the front side.
3.
Pull the snow thrower out of the carton. Be sure not to
damage the chute, or any cables attached to the chute. The
chute is shipped under the shroud on the back side of the
carton. Check for any cable ties securing the chute and
remove if necessary.
Wing
Knobs
Carriage Bolts
Set-Up
Adding Fuel & Oil
Refer to the Engine Operator’s Manual packed with your snow
thrower for information on adding fuel and oil.
Wing
Knobs
Assembly
Positioning the Upper Handle
Figure 3-2
1.
Remove the wing knob and carriage bolt from the top of
the lower handle. See Fig. 3-1. It is not necessary to remove
the shoulder screw and flange lock nut below the wing
knob and carriage bolt.
3.
Tighten the previously removed hardware to secure the
handle in place. See Fig. 3-2.
Wing Knobs
Carriage Bolts
Wing Knobs
Figure 3-1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Align the holes in the chute base with the holes in the
lower chute and secure with the previously removed hex
washer screws. See Fig. 3-5.
Installing the Chute
1.
Place the chute handle on the lower chute as shown in Fig.
3-3. Be certain that the handle is aligned in the channel on
the chute and the tabs snap into place.
Channel
Tab
Figure 3-5
Figure 3-3
Installing the Recoil Starter Handle
2.
Remove the hex washer screws in the chute base. See Fig.
1.
Remove the eye bolt and handle knob from the manual
bag.
3-4.
2.
Place the eye bolt and handle knob on the upper handle as
shown in Fig. 3-6. Do not fully tighten the hardware until
instructed to do so.
Recoil Starter Handle
Eye Bolt
Hex Washer
Screw
Handle
Knob
Figure 3-4
Figure 3-6
NOTE: The opening of the eye bolt should face toward the
back of the snow thrower.
3.
4.
5.
Slowly pull the recoil starter handle up towards the eye
bolt.
Slip the recoil starter rope into the eye bolt from the back
side of the snow thrower. See Fig. 3-6.
Securely tighten the eye bolt and handle knob.
8
se c t i O n 3— as s e M b l y & se t -up
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls & Features
4
Auger Control
Recoil Starter Handle
Chute Control Handle
Chute Assembly
Shave Plate
Auger
Figure 4-1
Auger
Shave Plate
The shave plate maintains contact with the pavement as
the snow thrower is propelled, allowing snow close to the
pavement’s surface to be discharged.
When engaged, the auger rotation draws snow into the auger
housing and throws it out the discharge chute. Rubber paddles
on the auger also aid in propelling the snow thrower as they
come in contact with the pavement.
Recoil Starter Handle
The recoil starter handle is used to manually start the engine.
Auger Control
Located on the upper handle, the auger control is used to
engage and disengage drive to the auger. Squeeze the control
against the upper handle to engage the auger; release it to
disengage.
EZ Chute
The rotation of the chute is controlled by rotating the chute
control handle left or right. The angle/distance that snow is
thrown is changed by manually tilting the upper chute to the
desired position.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
5
NOTE: Refer to the Engine Operator’s Manual for instruction on
starting, stopping and operating the engine.
Chute
Refer to Fig. 5-2 for the chute controls.
Engaging the Auger
Chute Control
Handle
1.
To engage the auger and start throwing snow, squeeze the
auger control against the handle. Release to stop the auger.
See Fig. 5-1.
Upper
Chute
Auger
Control
Handle
Wing Nut
Figure 5-2
To increase the angle/distance snow is thrown, pull up/back on
the upper chute. To decrease the angle/distance snow is thrown,
push down/forward on the upper chute.
Figure 5-1
To rotate the chute to the left, turn the chute control handle to
the right. To rotate the chute to the right, turn the chute control
handle to the left.
Engaging the Drive
Lift up slightly on the handle to allow the rubber paddles on the
auger to contact the pavement and propel the snow thrower
forward. Pushing downward on the handle will raise the auger
off the ground and stop the forward motion.
NOTE: Excessive upward pressure on the handle will result
in premature wear on the rubber auger blades which will
not be covered by the warranty.
Clearing a Clogged Discharge Chute
WARNING! Never use your hands to clear a
clogged chute assembly. Shut off engine and remain
behind handles until all moving parts have stopped
before using the clean-out tool to clear the chute
assembly.
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with snow
throwers. Never use your hand to clean out the discharge chute.
To clear the chute:
1.
SHUT THE ENGINE OFF!
2.
Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3.
Always use a clean-out tool, not your hands.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance & Adjustments
6
6.
Inspect the spark plug. If it is wet, clean off any oil before
re-installing.
Adjustments
WARNING! Before servicing, repairing or
inspecting the snow thrower, disengage the auger
control. Stop the engine and remove the key to
prevent unintended starting.
Control Cable
As a result of both the control cable and the auger drive belt
stretching due to wear, periodic adjustments may be necessary. If
the auger seems to hesitate when rotating, proceed as follows:
Shave Plate
The upper hole in the control handle provides for an adjustment
in cable tension. To adjust, disconnect the end of control cable
from the bottom hole in the control handle and reinsert it in the
upper hole. Insert the cable from the outside as shown in Fig. 6-2.
To check the adjustment of the shave plate, place the machine
on a level surface. The wheels, shave plate and auger should all
contact the level surface. Note that if the shave plate is adjusted
too high, snow may blow under the housing. If the shave plate
wears out excessively, or the snow thrower does not self-propel,
the shave plate may be too low and needs to be adjusted.
Auger Control Handle
NOTE: On new snow throwers or machines with a new shave
plate installed, the auger may be slightly off the ground.
To adjust the shave plate proceed as follows:
1.
2.
3.
Drain the gas from the snow thrower by running the
engine until it is empty.
Pull the recoil starter handle until resistance is felt. Then tip
the snow thrower back until it rests on the handles.
Loosen the four flange lock nuts and carriage bolts which
secure the shave plate to the housing. See Fig. 6-1. Move
the shave plate to the desired position and retighten the
nuts and bolts securely.
Control Cable
Figure 6-2
Side View
Carriage Screw
Test the snow thrower to see if there is a noticeable difference. If after
the adjustment to the control cable the auger still hesitates when
rotating, see the Service section for instructions on replacing the belt.
Flange Lock Nut
Reversible Shave Plate
Figure 6-1
4.
5.
Tip the snow thrower back to the operating position and pull
the starter handle a few times to see if it is difficult to pull.
If the starter is difficult to pull, remove the spark plug and
pull the handle several times to ensure that any oil trapped
in the head is removed.
CAUTION: Oil may come out of the spark plug hole
when it is removed and the starter handle is pulled.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
6.
Tip the snow thrower back to the operating position and pull
the starter handle a few times to see if it is difficult to pull.
Maintenance
Off-Season Storage
If the snow thrower will not be used for 30 days or longer, follow
the instructions below.
If the starter is difficult to pull, remove the spark plug and
pull the handle several times to ensure that any oil trapped
in the head is removed.
1.
Store the equipment in a clean, dry area.
CAUTION: Oil may come out of the spark plug hole
when it is removed and the starter handle is pulled.
2.
If storing the snow thrower in an unventilated area,
rustproof the machine using a light oil or silicone to coat
the snow thrower.
7.
Inspect the spark plug. If it is wet, clean off any oil before
re-installing.
3.
Clean the exterior of the engine and the snow thrower.
4.
Lubricate pivot points on control handle and extension
spring at end of control cable with a light oil.
Engine
Refer to the Engine Operators manual packed separately with
your snow thrower for maintenance and adjustment information
on your engine.
1.
To access the oil drain and spark plug it is necessary to
remove the lower panel.
2.
Remove the three screws that secure the lower panel.
Remove the lower panel by lifting up on the panel to free
the tabs at the bottom of the panel from the tab slots and
then pull back. See Fig. 6-3.
Figure 6-3
NOTE: The bottom of the panel has tabs that help hold it in
place.
NOTE: An oil drain extension kit is available separately.
Contact your local Cub Cadet dealer or contact Cub Cadet’s
Customer Support for kit #753-06684.
3.
Change the oil and/or the spark plug as instructed in your
Engine Operator’s manual.
4.
Re-install the lower panel by placing the tabs in the tab
slots, lifting the panel into place and secure with the three
screws removed in step 2.
12
se c t i O n 6 — Ma i n t e n a n c e & ad j u s t M e n t s
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
7
To replace the belt follow these instructions and refer to Fig. 7-3:
Replacing Belt
1.
Run the snow thrower until the fuel tank is empty.
Drive Pulley
2.
Pull the recoil starter handle until resistance is felt. Then tip
the snow thrower back until it rests on the handles.
Idler Pulley
3.
Slide a board up through the auger and through the chute
to secure the auger in place.
4.
Remove the belt cover by removing the three hex washer
screws and one hex lock screw that secure it to the frame.
See Fig. 7-1.
Belt Keeper
Flange Nut
Hex Lock Screw
Auger Pulley
Figure 7-3
NOTE: Installing the belt and belt cover may be easier if the
auger control is squeezed against the upper handle.
1.
Route the belt around the drive pulley and under the idler
pulley. See Fig. 7-3.
2.
Route the end of the belt around the auger pulley and slide
the pulley back on to the auger shaft. It may be necessary
to push down on the idler pulley to get the auger pulley
under the belt keeper.
Hex Washer Screw
Figure 7-1
3.
4.
5.
6.
Replace the flange nut and tighten securely.
Reinstall the belt cover removed earlier.
Remove the board from the auger and chute.
5.
Remove the flange nut that secures the auger pulley to the
auger shaft. See Fig. 7-2.
Tip the snow thrower back to the operating position and pull
the starter handle a few times to see if it is difficult to pull.
7.
If the starter is difficult to pull, remove the spark plug and
pull the handle several times to ensure that any oil trapped
in the head is removed.
CAUTION: Oil may come out of the spark plug hole
when it is removed and the starter handle is pulled.
8.
Inspect the spark plug. If it is wet, clean off any oil before
re-installing.
Flange Nut
Auger Shaft
Auger Pulley
Figure 7-2
6.
Remove the auger pulley and the belt.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Auger Paddles
Replacing Shave Plate
The shave plate is attached to the bottom of the auger housing
and is subject to wear. It should be checked periodically. There
are two wearing edges and the shave plate can be reversed.
The snow thrower auger’s rubber paddles are subject to wear
and should be replaced if any signs of excessive wear are present.
CAUTION: Do NOT allow the auger’s rubber
paddles to wear to the point where portions of the
metal auger itself can come in contact with the
pavement. Doing so can result in serious damage to
your snow thrower.
1.
Run the snow thrower until the fuel tank is empty.
2.
Pull the recoil starter handle until resistance is felt. Then tip
the snow thrower back until it rests on the handles.
3.
Remove the four carriage bolts and flange lock nuts which
attach it to the snow thrower housing. See Fig. 7-5.
To change the rubber paddles, proceed as follows:
1.
Run the snow thrower until the fuel tank is empty.
2.
Pull the recoil starter handle until resistance is felt. Then tip
the snow thrower back until it rests on the handles.
Side View
3.
Remove the existing rubber paddles by unthreading the hex
washer screws which secure them to the auger. See Fig. 7-4.
Carriage Screw
Flange Lock Nut
Hex Washer Screw
Auger Paddle
Reversible Shave Plate
Figure 7-5
4.
5.
6.
Install the new shave plate, making sure the heads of the
carriage bolts are on the inside of the housing.
Hex Washer Screw
Adjust the shave plate as instructed in the Maintenance &
Adjustments section.
Figure 7-4
Tighten securely once adjusted.
NOTE: The auger paddles should be replaced one-at-a-time
so that the auger still attached can be used as an example for Engine
positioning and re-installing the new auger.
Refer to the Engine Operators manual packed separately with
your snow thrower for service information for your engine.
4.
Secure the replacement rubber paddles to the auger using
the hardware removed earlier.
14
se c t i O n 7— se r v i c e
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Problem
Cause
Remedy
Excessive vibration
1. Loose parts or damaged auger.
1. Stop engine immediately and disconnect
spark plug wire. Check for possible damage.
Tighten all bolts and nuts. Repair as needed.
If the problem persists, take snow thrower to
an authorized service dealer.
Snow thrower fails to self-
propel
1. Auger control cable out of adjustment.
1. Adjust auger control cable as shown in
Maintenance & Adjustments section.
2. Auger drive belt loose or damaged.
2. Replace auger drive belt.
Augers continue to rotate
1. Auger control cable out of adjustment.
1. Adjust auger control cable as shown in
Maintenance & Adjustments section.
Snow thrower fails to
discharge snow
1. Chute assembly clogged.
1. Stop engine and disconnect spark plug wire.
Clean chute and inside of auger housing with
clean-out tool or stick.
2. Foreign object lodged in auger.
2. Stop engine immediately and disconnect the
spark plug wire. Remove object from auger.
3. Auger control cable out of adjustment.
3. Adjust auger control cable.
4. Auger belt loose or damaged.
4. Replace auger belt.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts
9
Component
Part Number and Description
731-08171
Shave Plate
954-04050
Belt
753-06469
946-04701
Rubber Auger Paddle Kit (Includes 2
paddles and 12 hex washer screws)
Clutch Cable
634-04347
751-10487
Wheel Assembly, 8”
Fuel Cap
731-05632
951-10292
Key
Spark Plug
Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial number
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
10
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
se c t i O n 10— nO t e s
Download from Www.Somanuals.com. All Manuals Search And Download.
se c t i O n 10 — nO t e s
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CUB CADET LLC
MANUFACTURER’S LIMITED WARRANTY FOR
SNOW THROWERS
The limited warranty set forth below is given by Cub Cadet LLC with
b. Cub Cadet does not extend any warranty for products sold or
exported outside of the United States and/or Canada, and their
respective possessions and territories, except those sold through
Cub Cadet’s authorized channels of export distribution.
respect to new merchandise purchased and used in the United States,
its possessions and territories, and by MTD Products Limited with
respect to new merchandise purchased and used in Canada and/or its
territories and possessions.
c. Replacement parts that are not genuine Cub Cadet parts.
For non-commercial use: Cub Cadet warrants this product (excluding
Normal Wear Parts, as described below) against defects in material
and workmanship for a period of three (3) years from the date of
original retail purchase or lease.
d. Service completed by someone other than an authorized service
dealer.
e. Transportation charges and service calls.
For commercial uses and applications: Cub Cadet warrants this
product (excluding Normal Wear Parts, as described below) against
defects in material and workmanship for a period of one (1) year from
the date of original retail purchase or lease.
No implied warranty, including any implied warranty of mer-
chantability of fitness for a particular purpose, applies after the
applicable period of express written warranty above as to the
parts as identified. No other express warranty, whether written
or oral, except as mentioned above, given by any person or
entity, including a dealer or retailer, with respect to any product,
shall bind Cub Cadet. During the period of the warranty, the
exclusive remedy is repair or replacement of the product as set
forth above.
The provisions as set forth in this warranty provide the sole and
exclusive remedy arising from the sale. Cub Cadet shall not be
liable for incidental or consequential loss or damage including,
without limitation, expenses incurred for substitute or replace-
ment lawn care services or for rental expenses to temporarily
replace a warranted product.
“Cub Cadet” will, at its option, repair or replace, free of charge, any
part found to be defective in materials or workmanship. This limited
warranty shall only apply if this product has been operated and
maintained in accordance with the Operator’s Manual furnished with
the product, and has not been subject to misuse, abuse, neglect,
accident, improper maintenance, alteration, vandalism, theft, fire,
water, or damage because of other peril or natural disaster. Damage
resulting from the installation or use of any part, accessory or
attachment not approved by Cub Cadet for use with the product(s)
covered by this manual will void your warranty as to any resulting
damage.
Normal Wear Parts are warranted to be free from defects in material
and workmanship for a period of thirty (30) days from the date of
purchase. Normal wear parts include, but are not limited to items
such as: belts, skid shoes, shave plates and tires.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply
to you.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service
dealer. To locate the dealer in your area:
In no event shall recovery of any kind be greater than the amount
of the purchase price of the product sold. Alteration of safety
features of the product shall void this warranty. You assume the
risk and liability for loss, damage, or injury to you and your property
and/or to others and their property arising out of the misuse or
inability to use the product.
In the U.S.A.
To locate the dealer in your area, check your Yellow Pages, or contact
Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or
com.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased as a
gift.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call
com.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have other
rights that vary in different jurisdictions.
This limited warranty does not provide coverage in the following
cases:
IMPORTANT: Owner must present Original Proof of Purchase to
obtain warranty coverage.
a. Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior finish
due to use or exposure.
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
GDOC-100160 REV. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|