To The Owner • Carton Contents • Assembly • Parts Lists • Warranty
OPERATOR’S MANUAL
Twin Rear Bagger Kit
For i1000 Series Lawn Tractors
with a 42” Timed Deck
Model 19A70001000
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
FORM NO. 769-03805A
4/10/2008
PRINTED IN U.S.A.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Use this page to make notes and write down important information.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS OF CARTON
Before beginning installation, remove all parts from the carton to make sure everything is present. Carton
contents are listed below and shown in Figure 2-1.
2
One Chute Tube
Two Mounting Brackets
One Cross-Support Bracket
Two Bracket Supports
One Catcher Support
One Discharge Chute Assembly
Two Grass Bag Assemblies
One Support Tube
Carton
Contents
One Grass Catcher Cover Assembly
Chute Tube
Discharge Chute
Assembly
If you are missing any
parts, call the Customer
Dealer Referral Line at
1-877-282-8684,
Support Tube
Grass Bag
Cover Assembly
or visit
find the nearest Cub
Cadet service dealer in
your area.
Bracket Support
Grass Bag Assemblies
Catcher Support
Mounting Bracket
Cross Support
Bracket
Figure 2-1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS OF HARDWARE PACK
This grass collector kit is shipped with a hardware pack enclosed. Please check your hardware pack against
the illustration below.
2
Carton
Contents
Group A
Assembling and Attaching Mounting Bracket
Clevis Pin (1)
Hex Bolt
5/16-18 x .750 (6)
If you are missing any
parts, call the Cus-
tomer Dealer Referral
Line at 1-877-282-8684,
or visit
Hairpin Clip (1)
Flange Lock Nut
5/16-18 (6)
find the nearest Cub
Cadet service dealer in
your area.
Hex Bolt
1/4-20 x .620 (8)
Flange Lock Nut
1/4-20 (8)
Figure 2-2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling and Attaching
The Bracket Assembly
(Hardware Group A)
IMPORTANT: Before assembly, place the tractor on
a firm, level surface, disengage the PTO, stop the
tractor engine and set the parking brake.
3
Assembling
and
1. Assemble the mounting bracket assembly as shown
in Figure 3-1.
Attaching
Mounting
Bracket
NOTE: The mounting bracket assembly may have been
preassembled at the factory, if this is the case, skip Step
1 and proceed to Step 2.
2. For convenience, pivot the seat forward and leave
it in that position until the grass collector is fully
mounted and assembled.
3. Position the bracket assembly to the outside of the
hitch plate. See Figure 3-2.
Figure 3-2
4. Push the hooked ends of the bracket assembly in (A)
and under the shoulder bolts (B) and swing in the
bottom down over the hitch plate aligning with the
hole on the hitch plate (C). See Figure 3-3.
5. Insert the clevis pin through the aligned holes in both
the bracket assembly and the hitch plate and secure
with the hairpin clip. Refer to Figure 3-4.
A
NOTE: There are two holes in the clevis pin. Be sure
to insert the hairpin clip in the upper hole to properly
secure the bracket assembly to the hitch plate.
IMPORTANT:
Before assembly, place
the tractor on a firm,
level surface, disengage
the PTO, stop the tractor
engine and set the park-
ing brake.
C
B
Figure 3-3
NOTE:
There are two holes in
the clevis pin. Be sure
to insert the hairpin
clip in the upper hole
to properly secure the
bracket assembly to the
hitch plate.
Upper Hole
Figure 3-1
Figure 3-4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching Grass Bags &
Grass Bag Cover
1. Place the support tube in position on the rear of unit
by sliding the support tube down through the holes in
the left side of the bracket assembly. Use the inside
hole on the bracket assembly. Refer to Figure 4-1.
4
Attaching
Grass Bags
& Grass Bag
Cover
2. Attach the grass bags by hooking them onto the grass
bag bracket using the slots in the grass bag and the
tabs on the grass bag bracket as shown in Figure 4-2.
3. Remove the clevis pins, belleville washers, and
hairpin clips, from the hinge brackets on the grass bag
cover.
4. Place the grass bag cover on top of the grass bags
and align the holes on the hinges of the grass bag
cover with the corresponding holes on the support
tube assembly. See Figure 4-3.
Figure 4-1
5. Insert the clevis pin through the hinge on the support
tube assembly and then through the grass bag cover.
See Figure 4-4.
6. Secure with belleville washer and hairpin clip with the
crown side of the washer going against the hairpin
clip. See inset images in Figure 4-4.
NOTE:
Insert the clevis pins
from the outside in as
shown in the inset
images of Figure 4-4.
7. Repeat with the second set of hardware through the
second hinge of the grass bag and the tube assembly
from the opposite direction.
NOTE:
It is very important to
maintain this order and
direction while installing
these hardware pieces.
After installation, make
sure that the grass bag
cover pivots on the sup-
port tube and opens.
NOTE: Insert the clevis pins from the outside in as
shown in the inset images of Figure 4-4. It is very
important to maintain this order and direction while
installing these hardware pieces. After installation, make
sure that the grass bag cover pivots on the support tube
and opens.
Figure 4-2
Figure 4-4
Figure 4-3
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching Discharge Chute
A
1. Lower the deck to its lowest position.
2. Raise the chute deflector on the deck (A) and hold it
while you position the discharge chute over the chute
opening. See Fig. 5-1.
5
B
3. Insert the pin (B) on the discharge chute into the hole
on the deck as indicated by the arrow in Fig. 5-1.
Attaching
Discharge
Chute
4. Push down on the discharge chute so that it covers
the opening of the deck completely.
C
5. Lock the discharge chute in position by stretching the
retainer strap over the front deck wheel bracket and
hooking onto the bottom of the bracket as seen in the
inset (D) in Fig. 5-1.
&
Bagger
Usage
D
6. Insert the curved end of chute tube into the hole in
the grass bag cover. See Fig. 5-2.
Figure 5-1
7. Place the lower end of the chute tube over the
discharge chute so that the tabs on the discharge
chute fits into the pockets on the chute tube. See Fig.
5-3.
8. Secure by hooking the two retainer straps of the
discharge chute to the pins on the chute tube. See
Fig. 5-3.
Bagger Usage
NOTE: When both grass bags are full, place the tractor
on a firm, level surface, disengage the PTO, turn the
tractor engine off and set the parking brake.
1. Flip Seat up.
2. Lift up grass bag cover. Do not remove the chute
tube assembly from the tractor.
3. Remove the grass bags by lifting these up and mov-
ing the bags away from the support tube assembly.
4. Empty the grass clippings at a proper disposal sight,
use the handle at the bottom of each grass bag.
Holding the bag firmly, empty the contents
Figure 5-2
5. Replace grass bags, close lid, flip down seat, restart
your tractor and resume cutting your grass.
Pocket
Tab
Figure 5-3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
6
NOTES
Use this page to take
notes and write down
important information.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4
18
11
12
2
16
14
19
17
20
12
21
14
8
17
13
1
7
30
32
14
20
20
14
9
7
28
29
26
13
17
31
24
27
14
25
13
23
10
22
9
6
3
15
10
Download from Www.Somanuals.com. All Manuals Search And Download.
REF
NO.
PART
NUMBER
DESCRIPTION
Bracket Support
8
1
2
3
4
5
6
7
8
9
16587D
16592
Illustrated
Parts List
Support Tube Assembly
Catcher Bag
764-0221
664-04017 Grass catcher Cover Assembly
683-04348 Mounting Bracket - RH
683-04350 Mounting Bracket - LH
710-0597
710-0751
710-3008
Screw 1/4-20 x 1”
Hex Screw 1/4-20 x0.620
Hex Screw 5/16-18 x 0.75”
10 711-0309A Clevis Pin
11 711-04069
12 711-1421
Grass catcher Pin
Clevis Pin
Y
13 712-04063 Flange Lock Nut, 5/16-18
14 712-04064 Flange Lock Nut, 1/4-20
15 714-0117
16 714-0145
Hairpin Clip
Click Pin
To order replacement
parts, call the Customer
Dealer Referral Line at
1-877-282-8684,
17 723-04008A Chute Strap - 6”
18 731-0899E Catcher Tube
or visit
19 736-0331
20 736-3092
21 783-0601
22 783-0765
23 864-0221
24 16591A
Bell Washer
find the nearest Cub
Cadet service dealer in
your area.
Flat Washer
Catcher Support Bracket
Cross Support Bracket
Grass Bag Assy.
Bag Hanger Bracket
Machine Screw, #10-24 x .5
25 710-0473
26 710-0604A Self-Tapping Screw 5/16-18
27 712-0272 Hex Sems Nut, #10-24
28 749-0701A Grass Bag Frame
29 711-05008
Belt Pin Guard, 1/4 x 1.43
30 731-06099 Chute Elbow, 42” Timing Deck
31 732-04510 Spring Hook
32 738-0754
Shoulder Screw, .437 x .54
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CUB CADET LLC
MANUFACTURER’S LIMITED WARRANTY
FOR SEPARATELY SOLD ATTACHMENTS AND ACCESSORIES
IMPORTANT: To obtain warranty coverage owner may be required
a. Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments, deck
adjustments, and normal deterioration of the exterior finish due to
use or exposure.
to present an original proof of purchase and applicable maintenance
records to the servicing dealer. Please see the operator’s manual for
information on required maintenance and service intervals.
The limited warranty set forth below is given by Cub Cadet LLC with
respect to new merchandise purchased or leased and used in the United
States and/or its territories and possessions, and by MTD Products
Limited with respect to new merchandise purchased or leased and
used in Canada and/or its territories and possessions (either entity
respectively, “Cub Cadet”).
b. Service completed by someone other than an authorized service
dealer.
c. Cub Cadet does not extend any warranty for products sold or
exported outside of the United States and/or Canada, and their
respective possessions and territories, except those sold through
Cub Cadet’s authorized channels of export distribution.
Cub Cadet warrants this product (excluding its Normal Wear Parts,
as described below) against defects in material and workmanship for
a period of three (2) years commencing on the date of original retail
purchase or lease and will, at its option, repair or replace, free of charge,
any part found to be defective in materials or workmanship.
d. Replacement parts and\or accessories that are not genuine Cub
Cadet parts.
e. Transportation charges and service calls.
f. Commercial or Institutional Use.
Normal Wear Parts are warranted to be free from defects in material and
workmanship for a period of thirty (30) days from the date of original
purchase or lease. Normal wear parts include, but are not limited to
items such as: belts, blades, blade adapters, grass bags, rider deck
wheels, seats, and tires.
There are no implied warranties, including without limitation any
implied warranty of merchantability or fitness for a particular
purpose. No warranties shall apply after the applicable period of
express written warranty above. No other express warranties beyond
those mentioned above, given by any person or entity, including a
dealer or retailer, with respect to any product, shall bind Cub Cadet.
The exclusive remedy is repair or replacement of the product as
set forth above. The terms of this warranty provide the sole and
exclusive remedy arising from the sale and/or lease of the products
covered hereby. Cub Cadet shall not be liable for any incidental or
consequential loss or damage including, without limitation, expenses
incurred for substitute or replacement lawn care services or for
rental expenses to temporarily replace a warranted product.
This limited warranty shall only apply if this product has been operated
and maintained in accordance with the Operator’s Manual furnished
with the product, and has not been subject to misuse, abuse, neglect,
accident, improper maintenance, alteration, vandalism, theft, fire, water,
or damage because of other peril or natural disaster. Damage resulting
from the installation or use of any part, accessory or attachment not
approved by Cub Cadet for use with the product(s) covered by this
manual will void your warranty as to any resulting damage. In addition,
Cub Cadet may deny warranty coverage if the hour meter, or any part
thereof, is altered, modified, disconnected or otherwise tampered with.
Some jurisdictions do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply to
you.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF
OF PURCHASE AND APPLICABLE MAINTENANCE RECORDS, through
your local authorized service dealer. To locate the dealer in your area:
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of the
product shall void this warranty. You assume the risk and liability for
loss, damage, or injury to you and your property and/or to others and
their property arising out of the misuse or inability to use the product.
In the U.S.A.:
Check your Yellow Pages, or contact Cub Cadet LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, call 1-877-282- 8684
This limited warranty shall not extend to anyone other than the original
purchaser or to the person for whom it was purchased as a gift.
In Canada:
Contact MTD Products Limited, Kitchener, ON N2G 4J1, call 1-800-668-
HOW LOCAL LAWS RELATE TO THIS WARRANTY: This limited warranty
gives you specific legal rights, and you may also have other rights that
vary in different jurisdictions.
Without limiting the foregoing, this limited warranty does not provide
coverage in the following cases:
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019, Phone: 1-877-282-8684
MTD Products Limited, Kitchener, ON N2G 4J1, Phone: 1-800-668-1238
GDOC-100177 REV. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|