COOKER HOOD
USER HANDBOOK FOR
INSTALLATION AND OPERATION
MODELS CRC95
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Page
Electrical Requirements
Get to know your Cooker Hood
Installing your Cooker Hood
Operating your Cooker Hood
The Controls
2
4
5-8
9
Do’s and Don’ts
Caring for your Cooker Hood
Filters and their Replacement
Cleaning
10
How to Replace the Light
Troubleshooting
11
Key Contacts
Back Cover
Appliance manufactured in EU.
Retention of the Instruction Book
This Instruction Book must be kept handy for reference as it contains important details on the
safe and proper use of the appliance.
If you sell or pass the appliance to someone else, or move house and leave it behind, make sure
this Book is also provided so the new owner can become familiar with the appliance and safety
warnings.
If the book is lost or damaged a copy may be obtained from:
GDA Ltd., Morley Way, Peterborough, PE2 9JB
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Get to know your Cooker Hood.
Unpacking - This is a two person operation.
Before installation, ensure that you have removed all packing pieces.
Ensure the fixing kit, ducting spigots and literature pack are retained with the hood.
Chimney Section
Controls
Glass Visor
Worktop Lighting
Filter Grille
Performance Table
No. of speeds Pressure Pa
3 360
Capacity (m3/h)
Noise Level
MIN
MAX
MIN
MAX
225
600
45
68
Dimensions of your Cooker Hood
Height adjustable from: 660mm to 965mm
Width
900mm
Depth 500mm
All measurements are in millimetres.
298
298
Min 660
Max 965
468
900
500
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing your Cooker Hood
SAFETY WARNINGS: THIS COOKER HOOD IS NOTE: All installations must comply with
DESIGNED FOR DOMESTIC USE ONLY.
local authorities and building regulation
requirements for the discharge of exhaust
air into the atmosphere.
When installed above a cooking appliance,
the distance between the surface of the hob
elements and the lower grille of the chimney
hood must be as follows:
Minimum 650mm - over an electric hob.
Minimum 750mm - over a gas or mixed fuel
hob.
All the fittings are supplied. If the hood is to
be installed onto a hollow construction or
plaster board wall, then special fixings will
have to be purchased.
This chimney hood is not suitable for
Before drilling, care should be taken to check
installation above a cooking appliance with for electric cables, water pipes or gas pipes in
a high level grill.
the location where the cabinet/canopy is to
be fitted.
If the hood can only be fixed to a hollow
construction plaster or partition board
structure, then the wall must be sufficiently
reinforced to be quite rigid in the area of the
mounting brackets.
To avoid the risk of accidents when fitting the
canopy and chimney to the wall or ceiling
please read and follow the installation
instructions.
THERMAL CUT-OUT:
The fan motor of this appliance incorporates a
thermal cut-out device which will operate if
the hood is installed below the minimum
recommended heights listed above, or if the
motor becomes overheated. If the cut-out
device is activated, switch off the fan motor
and allow the hood to cool.
The cut-out device will reset itself when the
fan motor has cooled significantly.
For ease of installation proceed as follows:
1. Fix the wall brackets.
2. Fix the canopy hood.
3. Connect the hood to the mains supply
ensuring that the canopy is functioning
correctly.
4. Select the type of installation, ie. ducting or
recirculation.
5. Fix the chimney stack.
NOTE: This hood has been designed and
approved for installation over an electric hob
with a maximum input of 7kW or a gas hob
with a maximum input of 10kW when fitted in
accordance with the heights recommended
above.
Your Cooker Hood can be installed either
for recirculation back to the room or
extraction through an outside wall.
NOTE: The hood is more efficient in the
exhaust mode, therefore, this position
When used in the extraction mode the Cooker should be selected during the warmer
Hood ducting must not be connected to a
flue which is used for exhausting fumes from
a central heating flue or water heating flue.
months of the year when no heating is
being used. When the room is being
heated, if the recycle position is selected
heat will not be wasted.
IMPORTANT: The exhaust air must not be
expelled through a smoke or waste-gas
chimney which is in use or through a shaft
used for ventilating rooms or into the
cavity of a cavity wall or into a cupboard
above the cooker hood.
If the room contains, a flued fuel burning
appliance, such as a gas or oil fired central
heating boiler which is not of the ‘Balanced
Flue’type, you should make sure that there is
adequate air inlet into the room at all times,
so that fumes from the boiler are not drawn
back into the room by the Cooker Hood.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing your Cooker Hood
Wall Mounted Model
3. Drill the two holes for the wall bracket,
Lower Fixings
insert the wall plugs and fit the bracket
using the screws provided.
1. Draw a vertical line on the wall, from the
centre of the cooking appliance, up to the
ceiling. Check the line is vertical using a
spirit level.
2. Put the template provided on the wall
paying particular attention to positioning
distances (see page 5).
3. Drill two holes (Fig.6 2) and insert wall
plugs.
3. Fit two hooks in the drilled holes (Fig.6 4)
using screws (Fig.6 5).
If the hood is to be installed onto a hollow or
plasterboard wall, special fixings will be
required.
FIXING THE CANOPY HOOD:
1. Remove the metal filter.
2. Hang the rear of the hood canopy on the
hooks and adjust the position of the hood
using the adjusting screws (Fig.6 6 & 7).
3. Whilst the hood is positioned, mark the
two holes (Fig.6 9).
Upper Fixing Bracket
1. Draw a horizontal line through the vertical
line, 15mm from the ceiling. Check the line
is level using a spirit level.
2. Place the chimney support bracket
(Fig.6 13) over the line, ensuring the
bracket is level. Mark the positions for the
fixing screws (Fig.6 14).
4. Remove the hood and drill the two holes.
Insert the wall plugs, return the hood to
the hooks and fix in place with the two
screws (Fig.6 10).
Fig.6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing your Cooker Hood
RECIRCULATION:
EXTRACTION:
Ducting Fitting
The chimney hood is supplied specified for
installation in the extraction mode. To convert The chimney hood can be ducted to the out-
to recirculation it will be necessary to obtain
the optional carbon filter.
In the recirculation mode, contaminated air
enters the chimney hood and passes through
side, using either rigid or flexible ducting of
150mm. The choice of ducting is left to the
discretion of the installer, however, the best
performance will be obtained by using
the grease filter and carbon filter and then out 150mm of rigid ducting. Where flexible duct-
into the kitchen through two grilles, at either
side of the chimney.
ing is fitted it should not be turned through
very tight bends as this could impair the per-
formance of the hood.
To convert the chimney hood to recirculation
proceed as follows:
1. Remove the metal grease filter, push the
securing tabs towards the centre and pull
the filter downwards (Fig.7).
Fig.9
Fig.7
The ducting must be manufactured from fire
retardant material conforming to the relevant
British Standard or DIN 4102-B1.
2. Fit the carbon filter and secure to the hood
with two screws provided (Fig.8).
Fig.8
3. Push the metal grease filter back into
place.
4. Fit the recirculation spigot (Fig.6 15F) to
the ducting pipe as illustrated on the
installation instructions.
NOTE: The two venting grilles must not be
fitted into the chimney stack until the
chimney stack has been installed onto the
wall above the canopy.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing your Cooker Hood
Fitting the Chimney Stack:
To fit the upper chimney section, first expand
the chimney slightly to allow it to be fitted
over the wall brackets. Then secure the upper
section using the two self tapping screws
provided.
The lower chimney section should be located
following instructions on page 6, ensuring
that the lugs in the base of the chimney are
seated into the two recesses on either side of
the canopy.
Fig.10
ATTENTION: Should the lower chimney
section subsequently be removed, the two
securing lugs in the top canopy must be
released.
Once the chimney stack has been installed, fit
the two venting grilles into the apertures
located on either side of the upper chimney
stack. The grilles are marked with two arrows
and should be fitted with one arrow pointing
upwards and the other towards the front.
When used in the recirculation mode, ensure
the grilles are properly secured to the
recirculation spigot.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your Cooker Hood
The Controls
Make sure that the Cooker Hood is wired in
and the power supply is switched on.
Fan Speed
Your Cooker Hood has three speeds to give
you the correct extraction level to suit your
cooking conditions.
The Cooker Hood functions are controlled by
five push buttons, located on the front face of
the hood.
Button d Position 1 should be selected when
simmering or when using only one pan.
Button e Position 2 should be selected for
normal cooking up to four pans.
To obtain the best performance it is advisable
to switch on the chimney hood a few minutes
before you start cooking and leave it running
for approximately 15 minutes after finishing.
Button f Position 3 should be selected when
frying or cooking food with strong odours.
Simply press the required fan speed selector
button.
Button c turns the selected fan speed ‘OFF”
a is an indicator light.
Work Top Illumination
Button b controls the two lights. Press to turn
‘on’, press again to turn ‘off’.
a
d
b
e
f
c
Indicator Light
Do’s and Don’ts
DO
DON’T
Don’t
Do take extra care when frying.
Do keep the heating areas on your hob
use the hood without the grease
filter.
covered over with pots and pans etc.
when using the hob and Cooker Hood
simultaneously (especially if you are
using a gas hob).
Don’t
Don’t
leave a naked flame under the hood.
leave cooker/hob hotplates ‘On’
when not covered, as the fan motor
of this cooker hood incorporates a
thermal cut-out device which will
operate if the hood overheats. The
fan motor will take approximately 20
minutes to automatically reset at
which point the hood will resume
normal functions.
Do make sure that there is an adequate air
inlet into the room if you are using the
hood to vent externally and have a boiler
or fire in the room, so that fumes are not
drawn back from the flue.
Do install the hood at the correct height,
allowing at least the minimum distance
above a cooking appliance (see page 5).
NEVER do flambé cooking beneath this
cooker hood.
NEVER leave frying pans or deep fat fryers
unattended during use, overheated
fat/oil may catch fire.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for your Cooker Hood
Before doing any cleaning or replacing the
filters or light bulb, always ensure that the
electricity supply to the Cooker Hood is
switched ‘OFF’.
Cleaning:
For your own safety and in the interest of
hygiene your Cooker Hood needs to be kept
clean. A build up of grease or fat from
cooking could cause a fire hazard.
Never use excessive amounts of water when
cleaning, particularly around the control panel
area.
Filters and their replacement:
THE METAL GREASE FILTER -
The grease filter is fitted to absorb grease and
dust during cooking to help keep the
appliance clean inside.
The metal casing and grille assembly should
be cleaned at least once a month to keep it
looking like new. Wipe over with a soft cloth,
wrung out in warm water and dry with a clean
soft cloth. Wear protective gloves.
You can use mild non-abrasive cleaners but
always read the manufacturer’s instructions
first. Always test their suitability on a small
area of the Cooker Hood not noticeable in
normal use.
The metal filter must be cleaned frequently, at
least once every thirty days of normal use.
The filter should be handwashed in hot soapy
water. Alternatively it could be washed in a
dishwasher.
After cleaning the filter, dry thoroughly before
reinstalling.
NOTE: DO NOT use scouring pads or
abrasive cleaners as they may scratch the
surface.
IMPORTANT:There could be a possible fire
hazard if the grease filter is not cleaned
when necessary and according to these
instructions.
How to replace the light:
Should the light fail to work, switch ‘Off’the
mains supply to the Hood.
TO REMOVE THE GREASE FILTER -
Release the catches on the filter (Fig.7 on
page 7), then the filter can be removed.
Unscrew the lamp cover (Fig.11) and first
check the bulb is screwed securely into the
lamp holder then switch ‘On’ at the mains
supply.
If the light still fails to work do not worry, it
will not affect the working of your hood.
Obtain a replacement halogen 20 Watt max
lamp.
THE CARBON FILTER -
The carbon filter absorbs odours arising from
the cooking. In use, the filter will slowly
become saturated and gradually less effective. Switch ‘Off’the mains supply. Unscrew the old
The filter will normally require changing every bulb anti-clockwise to remove and replace
six months, depending on the amount and
type of cooking.
NOTE: The carbon filter must never be
washed.
with the new bulb turning clockwise until
secure.
Refit the lamp cover and switch back ‘On’at
the mains supply.
TO FIT THE CARBON FILTERS -
NOTE: When changing the bulb, an
identical replacement must be fitted to
ensure the safe operation of the hood.
1. Remove the metal grease filter.
2. Remove the two securing screws from the
carbon filter.
3. Remove the old carbon filter, replace with
the new one.
4. Replace the securing screws to fix in place.
5. Replace the metal grease filter.
Fig.11
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting.
First, don’t panic!
Parts
There may be nothing wrong at all. Look for
your problem below, then check the things we
suggest.More often than not, this will give you
the answer to your problem, and you’ll be able
to carry on without having to telephone your
Service Office.
Please remember your new appliance is a
complex piece of equipment.
‘DIY’repairs or unqualified and untrained
service people may put you in danger, could
damage the appliance and might mean that
you lose cover under the Guarantee.
It is not working!
Are you using a plug and socket?
- Check that the plug is firmly pushed in.
- Check the power supply, by plugging in
another appliance.
If you do experience a problem with the
appliance, don’t take any risks, call in a Service
Engineer (See back cover).
- Has the fuse blown?
Our Parts are designed exclusively to fit only
GDA Ltd appliances. Do not use them for any
other purpose as you may create a safety
hazard.
It is not working!
Is the mains lead wired directly into a
double pole isolating switch?
- Check that the wires in the mains lead are
correctly connected.(See page 2)
The Cooker Hood is not working
satisfactorily...
- Check you have selected the correct fan
speed.(See page 9)
- Check you have left the cover over the
recirculation grille on top of the Hood,
extraction only (See installation).
- Check if the grease filter needs cleaning
(See page 10).
The light is not working...
- Check the bulb is screwed in securely.
- Replace the light bulb (See page10)
The Cooker Hood switches off
intermittently...
- Check the mounting height above the
hob is correct (See page 5).
The heat from the hob may cause the fan
motor to overheat/cut-out.
If, after following these instructions, you are
still having problems, contact your nearest
Service Centre (See back cover).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Conta cts
Service
Creda has the largest appliance manufacturer’s service team in Europe, trained
specialists directly employed by us to ensure your complete confidence.
Repair Service
UK: 08709 066 066
Republic of Ireland: 1850 302 200
You will be asked for the following information:-
Name, address and postcode.
Telephone number
Model / Serial number of the appliance
Clear and concise details of the query or fault
Place and Date of purchase
(Please keep the receipt as evidence will be required when the engineer calls).
Extended Warranty
To join: UK 08709 088 088
Republic of Ireland: 1850 502 200
Genuine Parts & Accessories
Mail Order Hotline
UK: 08709 077 077
Republic of Ireland: (01) 842 6836
For further product information 08701 54 64 74
All Creda Services are offered as an extra benefit and do not affect your statutory rights.
General Domestic Appliances Limited, Morley Way, Peterborough, PE2 9JB
Part No. FP084-01
Download from Www.Somanuals.com. All Manuals Search And Download.
|