Tumble Dryer
Instruction Book
5kg Models
You must read these instructions prior to using the
appliance and retain them for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
For your safety
IMPORTANT
Using your Tumble Dryer is easy.
Nevertheless, for your own safety and to get the best results it is important to know your
Dryer by reading right through this handbook before using your dryer for the first time.
NEVER ꢀ Allow children to play with or otherwise interfere with the dryer.
NEVER ꢀ Allow the air inlet at the back of the dryer, the air outlet or vent hose
to be obstructed.
NEVER ꢀ Direct the vent hose outlet towards the air intake at the back of the
machine.
NEVER ꢀ Allow the tumble dryer to recycle exhaust air.
NEVER ꢀ Switch the machine off leaving a hot load in the drum.
NEVER ꢀ Tumble dry without the filter in position.
NEVER ꢀ Exceed the maximum load capacity recommended or place
dripping wet items in the drum.
NEVER ꢀ Use the dryer on a carpeted floor where the pile height would
prevent air from entering the dryer from the base.
NEVER ꢀ Allow lint to collect around the dryer.
NEVER ꢀ Add liquid or sheet fabric conditioner to the dryer, use liquid
conditioner in the final rinse of your wash.
NEVER ꢀ Use the dryer for commercial drying, the dryer is only suitable for
domestic use.
NEVER ꢀ Dry Acrylics on the high heat setting.
NEVER ꢀ Tumble dry articles that have NOT been well washed in water and
detergent then well rinsed and spun.
NEVER ꢀ Tumble dry articles that have had chemicals used for cleaning.
NEVER ꢀ Dry articles that are contaminated with flammable substances such
as: petrol, oil, paint, hair lacquer, creams, cooking fat or oil.
NEVER ꢀ Tumble dry: rubber, foam rubber, plastic, plastic foam, nappy pants
or liners, polythene or paper.
Large, very bulky items including duvets and sleeping bags.
NEVER ꢀ Never attempt to stand on top of your dryer, it is not designed for
such use and you could injure yourself or damage the dryer by such
abuse.
NEVER ꢀ Switch electricity On or Off with wet hands.
IMPORTANT
A CHILD COULD CLIMB INTO OR TAMPER WITH AN UNATTENDED
TUMBLE DRYER.
WHEN THE MACHINE IS NOT IN USE SWITCH OFF, REMOVE THE PLUG AND
CLOSE THE DOOR.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
For your safety
ALWAYS ꢀ When the dryer is not in use, switch off at the wall, remove plug
and close the door.
ALWAYS ꢀ Comply with the specified electrical requirements.
ALWAYS ꢀ Ensure that your dryer is installed correctly and has adequate
ventilation. (see, "Where to put and vent your dryer.")
ALWAYS ꢀ Use the vent hose for optimum drying performance.
ALWAYS ꢀ Finish every programme with the cool tumble cycle provided on
the control.
ALWAYS ꢀ Clean the filter, it is essential that the filter is kept clear of fluff
after EACH drying cycle.
ALWAYS ꢀ Observe the rules for drying garments:
In particular woollen articles should not be dried in a
tumble dryer unless they are labelled ‘Superwash’,
‘Machine washable’ or have the ‘May be tumble dried’
symbol:
If in any doubt do not dry wool in the machine.
Unlike other materials, the mechanism of wool
shrinkage is irreversible, i.e. it will not stretch back to
the original size and shape.
ALWAYS ꢀ Buy genuine accessories and spares.
CAUTION: WHEN THE DRYER IS IN USE AVOID
TOUCHING THE REAR OF THE DRYER AS IT MAY
BE HOT.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Requirements
WARNING: This appliance must be earthed!
Supply
REFER TO THE RATING PLATE FOR VOLTAGE AND CURRENT
REQUIREMENTS. (see diagram for location.)
The flexible mains lead is supplied fitted with a BS1363 plug and
with a 13 amp BS1362 fuse.
The plug should be connected to the mains supply via a suitable
switched socket which is accessible after installing your dryer.
Changing
the fuse
If it is necessary to fit a replacement fuse, it must be a 13 amp
ASTA approved to BS1362 type.
Moulded plug
WARNING: The plug must not be used without a fuse cover.
If a replacement fuse holder/cover is required, it must be of the
same colour coding or wording as shown on the base of the plug.
Replacements are available from your Spares stockist.
Changing
the plug
The wires in the mains lead are coloured in accordance with the
following:
GREEN/YELLOW - EARTH
BLUE
BROWN
- NEUTRAL
- LIVE
Rewirable plug
GREEN &
YELLOW TO
EARTH
If a replacement plug is to be fitted, the appropriate wire must be
connected to the correct terminal,as follows:
Connect:
Green/Yellow to terminal marked Earth or Green or
Blue to terminal marked Neutral or N or Black
13 AMP Brown to terminal marked Live or L or Red.
FUSE
If the plug being replaced is a non-rewirable type then the cut-off
BROWN
TO LIVE
plug must be disposed of safely. DO NOT leave where it can be
inserted into a socket and create a shock hazard.
BLUE TO
NEUTRAL
CORD
CLAMP
Changing the
mains cable
Should the mains lead ever require replacing at any time please
contact your nearest Service Centre. A charge will be made for the
replacement of the mains lead or if you require a longer lead.
The mains lead must only be replaced by a specially prepared
cable obtainable from your Spares Stockist and fitted by a
qualified electrician.
NOTE: IF IN DOUBT ABOUT ANY OF THE ABOVE CONSULT A
QUALIFIED ELECTRICIAN.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Features - Get to know the main parts of your dryer
See “The Controls”
NOTE: if your dryer is new wipe out
the inside of the drum before you first
use it to remove any dust which may
have accumulated during transit.
Drum
FLUFF FILTER
Clean after
each use
Model and
serial numbers
Fig. 2
Front vent with hose
(Vent cover at rear)
Rating Plate
Fig. 1
Air Intake
grill
Vent Cover
Fig. 4
Caution
Hot
Fig. 3
Vent hose
fitted here
Wall/window vent
(Vent cover at front)
Rear venting with hose
(Vent cover at front)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Where to put and vent your dryer
ꢀ
Your tumble dryer should NOT be located adjacent to a gas hob,
cooker, heater, or eye level grill as flames from the burners could
cause damage to your machine.
ꢀ
ꢀ
When the dryer is fitted under a work surface, allow space for air
to enter the rear grille, 10mm above the dryer minimum.
If you are using this dryer adjacent or stacked on top of a
washing machine SEPARATE mains plugs and sockets must be
used for each appliance. DO NOT use 2-way adaptors or
extension leads.
Both your tumble dryer and front loading washing machine are
similar in design allowing the tumble dryer to be permanently
stacked on top saving you valuable floor space. A special
stacking kit complete with instructions is available from your
retailer or nearest Spares Centre.
Stacking it on
your washing
machine
IMPORTANT:
Only use genuine stacking kits. When ordering you must
state the model numbers of both your Washing Machine and
your Tumble Dryer. Unsuitable kits may result in potential
hazard and will invalidate your warranty rights.
Some models are designed to give the option of venting the moist
air from the front of the dryer. The dryer as supplied is rear
venting. Some models can be converted to front venting by
removing the vent cover from the aperture on the front (Fig. 1) of
the dryer and fitting it in the aperture at the back.
When operating the dryer, there has to be adequate ventilation to
avoid the back flow of gases into the room from appliances
burning other fuels, including open fires.
Venting options
ꢀ
ꢀ
ꢀ
A vent hose is recommended for optimum performance.
A vent hose must be used if the rear venting option is used.
(If this is not supplied it can be obtained from your retailer or
Spares Centre).
ꢀ
ꢀ
When front venting without a hose a window must always be
opened to reduce condensation.
The hose must be fitted securely into the dryer, as shown on the
diagrams on the previous page. If possible it is always best to
connect the hose to a permanent outlet close to the dryer (see
instructions on next page).
ꢀ
ꢀ
Ensure that the end of the hose is not directed towards the
air intake grille at the rear of the dryer.
If permanent installation is not possible, the dryer will work just as
well with the hose passed through a partly opened window. (See
diagram on next page).
NOTE: The vent hose should not exceed 2.4 metres in length,
and should be kept free of any possible accumulation of fluff
lint (and water) by frequently shaking it out. Always ensure
that the hose is not squashed.
ꢀ
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Where to put and vent your dryer
Permanent
Venting
In conjunction with the vent hose we recommend the use of a
Wall/Window Vent Kit. These are available from your retailer or
nearest Spares Centre.
Wall/Window
Venting
Fitting instructions are supplied with the kits, which can be mounted
through a wall or window. Details of positioning for wall mounting
are as follows:- Break a hole through the wall to the left of the
proposed position for the dryer. Keep the hose as short and straight
as possible to prevent condensed moisture running back into the
dryer. Similarly the duct inserted into the wall should slope
downwards to the outside. For window venting with stacked dryer,
the hole in the window should ideally be made below the outlet and
the hose should be kept as short as possible.
Depending on the frequency of use, it is essential that the areas
A
B
A and B in the illustrations are checked periodically and any fluff
or debris removed.
It is particularly important that the vent hose adaptor is fitted
securely thus preventing any moisture laden air from being
emitted back into the room.
NOTE: The dryer should not be pushed so far back that the
hose adaptor is pulled out of position or the hose squashed.
The hose should be kept clear of the air intake grille and kinks
or ‘U’ bends avoided as these will obstruct the hose or trap
condensation.
Storm cover
WARNING:
1. ENSURE THAT THE DRYER IS ADEQUATELY
VENTILATED AND THAT THE END OF THE VENT HOSE
IS NOT DIRECTED TOWARDS THE AIR INTAKE DUCT.
2. THE DRYER MUST NOT RECYCLE EXHAUST AIR.
3. THE VENT HOSE MUST ALWAYS BE FITTED FOR
OPTIMUM PERFORMANCE.
4. MAKE SURE THAT THE VENT HOSE AND AIR INTAKE
GRILLES ARE NOT OBSTRUCTED OR BLOCKED.
5. MISUSE OF A TUMBLE DRYER MAY CREATE A FIRE
HAZARD.
6. DO NOT DISCHARGE THE EXHAUST AIR INTO A FLUE
WHICH IS USED FOR EXHAUSTING FUMES FROM
OTHER APPLIANCES BURNING GAS OR OTHER FUELS.
For open window venting it must be possible for the end of the hose
to be directed downwards to prevent warm, moist air condensing
in the room or in the dryer.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use your dryer
1. Plug in, switch
on electricity.
2. Sort your laundry
(see section “Sorting
Your Laundry”)
WARNING:
WHEN SWITCHING
ELECTRICITY ON
OR OFF, PLEASE
ENSURE THAT
YOUR HANDS ARE
DRY.
4. Load the dryer
placing the clothes
carefully in the drum
pushing them well
towards the back
and away from the
door seal. Close the
door.
3. Open the door.
Check that the fluff
filter is clean (see
section How to
remove and clean
the fluff filter).
5. Select the relevant heat setting
(see section “Sorting Your Laundry”).
When low heat is selected a coloured
indicator (on top of switch) will be
visible.
Button IN
HIGH HEAT
Button OUT
LOW HEAT
6. (Selected models only)
Select Audio Signal (Buzzer) option, if
required.
The buzzer is selected with the switch
button ‘IN’ and cancelled with the button
‘OUT’.
7. Select the
Button IN
required
Audio Signal ON
programme/ drying
time (See section
“The Controls”).
The dryer will start.
Button OUT
Audio Signal OFF
9. Switch off
electricity and remove
plug from socket.
8. When finished
open the door and
take out the laundry.
Clean and replace
the fluff filter.
WARNING:
WHEN SWITCHING
ELECTRICITY ON
OR OFF, PLEASE
ENSURE THAT
YOUR HANDS ARE
DRY.
Never switch the dryer off with a hot load in the drum.
You must terminate every programme with the Cool Tumble Phase.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
The Controls - Basic Models (not Reverse Action)
Heat Switch (OUT low heat, IN high heat)
Indicator
Turn the timer clockwise to select the required drying time.
Timer control
The drying time for both heat settings is controlled by the timer. All you
have to do is turn the Timer Control clockwise until the required time
appears in line with the indicator.
Do not rotate the knob beyond 120 minutes (maximum drying time),
or past the zero stop. If you have selected more time than you require
turn the knob anti-clockwise to select the correct time required.
This operation also starts the dryer, provided the door is closed and
the machine is plugged in. The “Guide To Drying Times” section will tell
you how much time you’ll need for various loads.
About 10 minutes before the programme is completed, the heating
elements will be switched off and the programme enters the final ‘Cool
Tumble’ phase. During this phase the fabric is cooled. You should
always allow the dryer to complete this phase.
The Cool Tumble
phase
By opening the door, the dryer will stop and you can check the dryness
of the load a often as you wish and, if you want, remove (or add) some
items before they are fully dry. (This is particularly useful for a mixed
load where you want to iron some items, but others are to be fully
dried).
We recommend that the clothes are removed immediately after this
programme to minimise creasing.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
The Controls - Anti Tangle (Reverse Action) Models
Indicator
Heat Switch (OUT low heat, IN high heat)
Turn the timer clockwise to select the required drying time.
Timer control
The drying time for both heat settings is controlled by the timer. All you
have to do is turn the Timer Control clockwise until the required time
appears in line with the indicator.
Never wind the timer control anti-clockwise.
This operation also starts the dryer, provided the door is closed and
the machine is plugged in. The “Guide To Drying Times” section will tell
you how much time you’ll need for various loads.
About 10 minutes before the programme is completed, the heating
elements will be switched off and the programme enters the final ‘Cool
Tumble’ phase. During this phase the fabric is cooled. You should
always allow the dryer to complete this phase.
The Cool Tumble
phase
By opening the door, the dryer will stop and you can check the
dryness of the load a often as you wish and, if you want, remove (or
add) some items before they are fully dry. (This is particularly useful for
a mixed load where you want to iron some items, but others are to be
fully dried).
We recommend that the clothes are removed immediately this
programme is finished to minimise creasing.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The Controls - Smart Dry Models
Heat Switch (OUT low heat, IN high heat)
Smart Drying Light
Audio/Audio Switch
Indicator
To set the required programme, all you have to do is turn the Timer
Control clockwise until the required selection appears in line with the
indicator. Never turn the timer control anti-clockwise.
This operation also starts the dryer, provided the door is closed and
the machine is plugged in.
1. Smart (Automatic) Drying Half (average) loads
2. Smart (Automatic) Drying Full (large) loads
3. Easy Iron Cycle
Programme
options
4. Timed drying (up to 60 minutes)
5. Cool Tumble Phase
The Smart Drying programmes will automatically dry most loads to the
fully dry ready to wear condition. This eliminates the need to guess the
drying times and saves energy. High Heat MUST be selected. (Heat
switch IN). To select Smart Drying turn the selector to position:
i) Automatic
Drying
S-HALF LOAD for average loads and S-FULL LOAD for large loads.
S-HALF LOAD Smart Drying average loads
1 to 3kg Cottons, Polycottons or Synthetics (Dry Weight).
S-FULL LOAD Smart Drying large loads
3 to 5kg Cottons (Dry weight)
When the door is closed the Smart Drying light will glow to indicate that
Smart Drying programme is running. When the load is dry, the selec-
tor will automatically advance to the 8 minute cool tumble phase.
Note:
•
•
•
If LOW heat is selected for a Smart Drying programme, the
dryer will advance to COOL without drying the load.
For acrylics and acrylic mixtures, select LOW heat and use
timed drying.
Small loads (less than 1kg) must be dried using the timed
drying programme.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
The Controls - Smart Dry Models (continued)
This light will glow when Smart Drying is selected. it will stop glowing
when the load is dry and the programme advances to the Cool Tumble
phase.
Smart Drying Light
ii) Easy Iron Cycle
This is a short programme of approximately 10 minutes to condition
previously dried clothes (See section “Easy Iron Programme”).
It consists of a period of heating followed by a short cool tumble
period (as detailed below).
Select high heat for this programme.
It should not be used on damp loads, as it is NOT a drying
programme.
iii) Timed Drying
To set the required time, all you have to do is turn the timer control
clockwise until the required time appears in line with the indicator.
Never turn the timer control anti-clockwise.
The chart in the section “Guide to Drying Times” will tell you how much
time you’ll need for various loads.
This programme is particularly useful in cases where a damp load is
required for ironing or LOW heat drying is required and also for small
loads.
About 10 minutes before the programme is completed, the heating ele-
ments are switched off and the programme enters the final ‘Cool
Tumble” phase.
iv) Cool Tumble
Phase
During this phase the fabric is cooled. You should always allow the
dryer to complete this phase.
By opening the door the dryer will stop and you can check the dryness
of the load as often as you wish and if you want to remove (or add)
some items before they are fully dry. (This is particularly useful for a
mixed load where you want to iron some items, but others are to be
fully dried).
After this cycle, the ready signal (buzzer) will sound (if selected) to
remind you that the clothes are ready to take out. To cancel, turn the
timer to 0 or press the option button (to its OUT position).
We recommend that the clothes Are removed immediately this
programme ends to minimise creasing.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Sorting your laundry
1. Always separate laundry into the correct fabric groups before
washing and drying.
2. See that all zips are closed, hooks and eyes are fastened and
belt, strings etc. are tied loosely in bows, you will normally have
done this for each item before the washing stage.
3. It is important to extract as much water as possible from each
item before drying. This saves you time and money.
WARNING: CLOTHES SHOULD NEVER BE LOADED
DRIPPING WET
4. Make sure that the items to be dried are suitable for tumble
drying, or are not of a type requiring ‘special attention’ (see“Wash
Care Labels” section).
Maximum
load size
Your dryer will hold a load of 5kg (11lb) dry weight of natural fabrics.
if you are drying items of man-made fibres (synthetic or acrylics), the
maximum load should not exceed 3kg (6.6lb) dry weight.
This difference is that man-made fibres require more space to
tumble-dry without creasing.
WARNING: DO NOT OVERLOAD AS THIS COULD RESULT
IN REDUCED DRYING PERFORMANCE AND A POSSIBLE
FIRE HAZARD.
Typical load
To help you estimate how many items it takes to make up a drying
load, the charts below show the approximate weights of some
everyday washing items.
Clothes
Household Items
Blouse
Cotton 150g 5oz
Duvet cover
(Double)
Cotton 1500g 3lb 5oz
1
2
Other
100g 3 / oz
Other
1000g 2lb 3oz
700g 1lb 6oz
Large Tablecloth
Small Tablecloth
Tea Towel
Dress
Cotton 500g 1lb 2oz
250g 9oz
Other
350g 12oz
1
Jeans
700g 1lb 6oz
1000g 2lb 3oz
2
100g 3 / oz
10 Nappies
Shirt
Bath Towel
700g 1lb 8oz
350g 12oz
500g 1lb 2oz
350g 12oz
1
2
Cotton 300g 10 / oz
Hand Towel
Double Sheet
Single Sheet
Other
200g 7oz
1
2
T-Shirt
125g 4 / oz
If you group small cotton or terry-towelling items with a synthetic
fabric load they could be damp at the end of the drying cycle. If this
happens simply give them an additional short period of drying to
finish them off.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash Care Labels
Most of today’s fabrics can be tumble dried in your Dryer with no
trouble at all, but there are certain fabric finishes which should be
dried away from direct heat.
The majority of garments now have wash-care labels on them, giving
full washing and drying instructions. These should always be
followed carefully especially when you are drying something for the
first time.
Typical symbols are:
May be tumble dried
Do not tumble dry
Or:
Tumble dry at high heat setting
Tumble dry at low heat setting
Items not suitable for tumble drying
•
Those containing foam rubber or rubber-like materials or plastic
film (e.g. pillows, cushions, PVC rainwear), or any other articles
which are inflammable or contain inflammable substances (e.g.
towels contaminated with hair lacquer
•
•
•
Fibreglass (e.g. some types of curtains)
Items which have been dry cleaned
Woollens. Woollen items need as much care in drying as they do
in washing. The movement of the tumble-drying action causes the
woollen fibre to shrink and distort.
•
•
Garments with the ITCL Code (see ‘Items Requiring Special
Attention’).
Do not tumble dry.
Large bulky items e.g. continental quilts, sleeping bags, pillows,
cushions, double blankets and large bedspreads. These expand
when drying and would prevent airflow through the Dryer.
WARNING: THE DRYER IS INTENDED FOR USE ONLY
WHERE WATER SOLUTION IS USED FOR THE CLEANING
PROCESS. MISUSE OF A TUMBLE DRYER MAY CREATE A
FIRE HAZARD.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Items requiring special attention
Blankets and
Bedspreads
The drying requirements of blankets and bedspreads will, of course,
vary tremendously according to size and weight. Some, however are
simply too big. if you have difficulty getting them into the Dryer, the
machine will have difficulty drying them properly. Blankets (and
Garments) made from Acrylic fibres (e.g. Acilan, Courtelle, Orion and
Dralon) must be dried with special care on Low heat setting.
Overdrying should be avoided to ensure heat creasing does not
occur.
Permanently
Your dryer will cope with such clothes very well, but you should
pleated or creased always read the manufacturer’s drying instructions attached to the
garments
garment before you begin.
Starched articles Starched articles should be dried together in the same load to avoid
the distribution of starch to non-starched items. You should use a
slightly heavier starch solution than you would when drying the items
on the washing line. Make sure that as much of the solution is
removed from the load as possible before placing it in the Dryer.
Remove the items from the dryer as soon as they reach ironing
dampness. If they are overdried the starch will powder, leaving the
fabric limp - which rather defeats the purpose of the exercise!
Fabric conditioner To make sure all your tumble dried clothes come out really fresh and
soft we recommend you use a liquid fabric conditioner in the final
rinse of your wash. A liquid fabric conditioner restores bounce and
softness and helps eliminate static cling.
WARNING: ON NO ACCOUNT SHOULD LIQUID OR SHEET
FABRIC CONDITIONER BE ADDED TO THE DRYER ITSELF.
Home dry cleaning Garments with the ITCL code
may be cleaned using one of the
Home Dry Cleaning Kits available.
The instructions supplied with the Home Dry Cleaning Kit must be
strictly followed.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Easy Iron Programme - Selected Models
‘Easy Iron’ provides a short programme consisting of approximately
7.5 minutes of heat with an approximately 2.5 minutes cool tumble
period. It is a short conditioning programme that softens the fibres
allowing them to relax making handling and ironing easier and less
time consuming.
However garments are dried, outside on the line, inside on a radiator,
hung around the home or using a tumble dryer, once dry they usually
get left in the same position/place for a long period of time. This tends
to cause garment fibre stiffness which can make the handling of
garments difficult and therefore the ironing time longer. Garments
dried in any of the ways described above and left will benefit from the
‘Easy Iron’ programme.
When to use
‘Easy Iron’
ꢀ The ‘Easy Iron’ cycle is not a drying programme. It has been
designed to condition/soften garments that have already been
dried and left unattended in this state for a period of time.
ꢀ All materials do not behave in exactly the same way when heated.
For instance, our testing has shown that materials such as
Tencel® and Acrylics are not relaxed quite as effectively by
applying the ‘Easy Iron’ cycle as we found on the more traditional
Cottons and Polycottons.
Important!
ꢀ To obtain the best results from ‘Easy Iron’ it is important that the
weights recommended below are not exceeded and HIGH heat is
selected. (Heat switch IN).
ꢀ For best results We recommend garments should be
removed from the dryer immediately after the ‘Easy Iron’
programme to be hung, folded neatly or ironed.
When this is not possible the ‘Easy Iron’ programme should
be repeated.
Recommended weights and materials
Material
Cotton and Cotton mixtures
Synthetics
Maximum load
2.5kg
5.5lb
4.4lb
4.4lb
2kg
2kg
Denim
On completion of the programme an audio signal is sounded (if
selected) to remind you to remove garments from the dryer.
Audio Signal
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Drying Times
Please note that the Drying Times stated below and on appliance
control panel are a GUIDE only and drying times are affected by:
The amount of
Items such as towelling retain a lot of water after spinning, also the
water remaining in suggested wash programme for small items such as T-Shirts may
the clothes after
spinning
sometimes incorporate a low spin speed which has the same effect.
The type of fabric Your drying load may contain the same type of fabric but of different
thicknesses. Thinner items will take less time to dry. Some fabrics,
such as those used for jeans are of closer texture than others and
although light when dry will be heavy after washing and spinning.
The quantity of
Single items of clothes or small loads may take disproportionally
clothes to be dried longer to dry. It is more energy efficient to dry larger loads.
How dry you want As it takes longer to fully dry clothes than to have them ready for
the clothes
ironing, you may wish to remove some clothes when they are slightly
damp, ready for ironing and then continue to dry the remainder until
they are fully dry.
The heat setting
The label on the garment should tell you the correct heat setting to
you have selected select. See ‘Wash Care Labels’.
The temperature
of the room
If the room in which the dryer is situated is cold, your clothes will take
longer to dry than if the room is warm.
Bulky items
Some bulky items such as padded jackets can be dried, with care,
and we do advise that you remove these items several times, shake
them and return them to the dryer. THERE ARE HOWEVER SOME
ITEMS THAT WE DO NOT ADVISE YOU TO DRY. SEE ‘ITEMS
NOT SUITABLE FOR TUMBLE DRYING’
Drying Guide - approximate drying time in minutes (weights specified are when dry)
COTTONS
SYNTHETICS
ACRYLICS
High Heat
High Heat
Gentle Heat
Drying times 800 - 1000rpm in washing
machine
Drying times on reduced
spin in washing machine
Drying times on
reduced spin in
washing machine
Half
load
Full
load
Half
load
Full
load
Half
load
Full
load
1 kg
2 kg
3 kg
4 kg
5 kg
1 kg
2 kg
3 kg
1 kg
2 kg
20 - 30 35 - 45 45 - 60 60 - 70 70 - 80 20 - 30 35 - 45 45 - 60 25 - 40 40 - 60
Be careful not to
overdry
All fabrics contain a little natural moisture even when ‘dry’ and this
natural moisture should not be lost if the clothes are to remain soft
and fluffy. Clothes that are dried for too long tend to wrinkle and will
need more ironing than usual giving you extra work that the dryer
was designed to remove.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
How to remove and clean the fluff filter
A very important part of your dryer is the fluff filter at
the front edge of the drum. It’s there to trap the parti-
Position of filter
cles of lint and fluff which are normally blown away
when clothes are dried on the washing-line.
if the filter is allowed to become blocked, the passage
of warm air through the drum will be severely restrict-
ed. This means your clothes will take much longer than
normal to dry and the cost of drying them will be
increased. it may also damage your dryer.
Small items, e.g. babies socks, may fall onto the filter.
These should be removed so that the filter is not
restricted.
WARNING: DO NOT OPERATE THE DRYER
WITHOUT CLEANING THE FILTER AFTER
EACH DRYING CYCLE. FAILURE TO CLEAN
THE FILTER MAY RESULT IN A FIRE HAZARD.
WARNING: NEVER USE SHEET
FABRIC CONDITIONER. IT MAY FALL
INTO THE FILTER AND RESTRICT THE
AIRFLOW THROUGH THE DRYER
Grip the centre rib and pull the filter upwards and for-
wards through the door seal (see diagram).
Open the filter, and remove the fluff that has collected
on the inside.
To remove the filter
Wash or vacuum clean the filter occasionally.
Don’t be alarmed by the amount of fluff you may find
on the filter. It’s part of the wearing, washing and dry-
ing process.
WARNING: DO NOT OPERATE THE DRYER
WITHOUT THE FILTER IN POSITION.
It is essential that the filter is replaced correctly. It must
be fitted so that the symbols, shown on the filter above,
face towards the front of the dryer. Ensure the filter is
fully located into the tumble dryer duct.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for your Dryer
Your tumble dryer needs very little attention. The following simple
steps will keep it performing well.
Switch off electricity and remove plug.
When finished
After each load
Always clean the filter and turn the drum by hand to check that small
items like handkerchiefs do not get missed.
Clean exterior metal and plastic surfaces with a damp cloth or silicon
polish only. Regularly check and clean if necessary, the vent hose and
any permanent venting fixture to ensure that there has been no accu-
mulation of fluff or lint during the drying process. Do not use abrasive
cleaners, scouring agents, acids, chlorine bleach or metal polish to
clean any part of the machine. These could damage the machine.
Clean fluff from the area behind the front venting adaptor fitted at the
lower left hand corner of the front panel (not fitted to rear venting only
models). The adaptor can be removed by turning it anti-clockwise a
twelfth of a turn. Refitting is the reverse of the above.
As necessary
Your tumble dryer uses special bearing components. Lubrication by
the user is not necessary and must not be attempted.
Lubrication
We strongly recommend that all appliances are regularly checked for
electrical and mechanical safety.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Spare parts
Please remember your new appliance is a complex piece of
equipment.
‘DIY” repairs or unqualified and untrained service people may put
you in danger, could damage the appliance, and might mean you
lose cover under the Parts Guarantee.
If you do experience a problem with the appliance don’t take risks,
call in our Service Engineer. Our Spare Parts are designed
exclusively to fit your appliance. Do not use them for any other
purpose as you may create a safety hazard.
Disposal of your product
To minimise the risk of injury to children please dispose of your
product carefully and safely.
Remove all doors and lids. Remove the mains cable (where fitted)
by cutting off flush with the appliance and always ensure that no
plug is left in a condition where it could be connected to the
electricity supply.
To help the environment Local Authority instructions should be
followed for the disposal of your product.
This appliance conforms to the following EEC Directives.
Low Voltage Equipment
72/23/EEC
93/68/EEC
Electromagnetic Compatability
89/336/EEC
92/31/EEC
93/68/EEC
21
Download from Www.Somanuals.com. All Manuals Search And Download.
If something goes wrong
First, don’t panic! There may be nothing wrong at all. Look for your
problem below, then check the things we suggest. More often than
not, this will give you the answer to your problem, and you’ll be able
to carry on without having to telephone your Service Centre.
If after this you still cannot get your machine to work, follow the
advice given on the next page.
Problem
Check these things first
‘It won’t start’
1. Is the machine plugged in and switched on at the socket?
2. Is the Timer Control set to required programme/time?
3. Is the door securely closed?
4. Has the fuse blown? (Try plugging in another appliance to check)
5. Have you used an extension lead? Many are not suitable. Try
plugging the dryer directly into a socket to check.
‘It is taking a long
time to dry’
(All Models)
1. Have you forgotten to clean the filter? Check it.
2. Have you selected the correct Heat setting for the type of fabric
you are drying? (IN for High, OUT for low).
3. Is the flexible vent hose squashed, blocked or kinked? Check it
for foreign objects or condensate (water).
4. Is the air inlet obstructed in any way?
5. Permanent venting - is flap on the storm cover obstructed?
6. Were the clothes ‘excessively wet’ when they were put in?
7. Was the correct programme/time selected?
8. Have you overloaded the dryer?
Auto Programmes
(Some models)
1. Has the correct programme been selected for the load?
3 - 5kg programme S - FULL LOAD
1 - 3kg programme S - HALF LOAD
Less than 1kg use timed dry programme.
2. Has high heat been selected?
The Smart Dry programmes will not operate on low heat, if low
heat is required use timed dry.
‘The dryer keeps
buzzing’ (Some
models)
This is perfectly normal, the dryer has finished its programme. Press
the Ready (Audio) button and the buzzing will stop or turn the Timer
Control to the off ‘O’ position.
Any other
problem
Have you re-read this instruction book?
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Contacts
Service
Creda has the largest appliance manufacturer’s service team in Europe,
trained specialists directly employed by us to ensure your complete
confidence.
Repair Service
UK: 08709 066 066
Republic of Ireland: 1850 302 200
You will be asked for the following information:-
Name, address and postcode.
Telephone number
Model / Serial number of the appliance
Clear and concise details of the query or fault
Place and Date of purchase
(Please keep the receipt as evidence will be required when the engineer calls).
Extended Warranty
To join: UK 08709 088 088
Republic of Ireland: 1850 502 200
Genuine Parts & Accessories
Mail Order Hotline
UK: 08709 077 077
Republic of Ireland: (01) 842 6836
For further product information 08701 50 60 70
All Creda Services are offered as an extra benefit and do not affect your statutory rights.
General Domestic Appliances Limited, Morley Way, Peterborough, PE2 9JB
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.
December 2001 Part No. 0766200033-02
Download from Www.Somanuals.com. All Manuals Search And Download.
|