IMI CORNELIUS INC.
One Cornelius Place
Anoka. MN 55303-6234
Telephone (800) 238–3600
Facsimile (763) 422–3246
DF/ED XXX LID KITS FOR THE FOLLOWING ICE MAKERS:
CORNELIUS XTREME SERIES
322/522/330/530/630/830/1030/1230
KITS FOR USE WITH CORNELIUS XTREME 322/522 22” SINGLE CURTAIN ICE MAKERS.
Dispenser
ED 100/150
(Black)
ED 150
(Black)
ED 175
(Black)
ED 2XX
(Black)
ED 300
(Black)
Kit Number
Components
1. Lid Assembly
2. Cover
629087940
629087939
629087938
629087937
629087936
Qty
1
620027505
52934
620046012
620043512
620037007
631500109
22127
620046011
620043512
620037007
631500109
22127
15276
15210
52969
52946
1
3. Ice Baffle
4. Bin–Stat Kit
5. Bracket
620037007
631500109
620027306
70217
620037003
631500109
22127
620042919
631500116
22127
1
1
2
6. Screw, Mounting
7. Gasket
70217
70217
70217
70217
6–8
87”
1
620050102
90221
620050102
90221
620050102
90221
620050102
90221
620050102
90221
8. Label
9. Acorn Nut, Nylon 620701902
10. Sealing Washer 620701901
620701902
620701901
621701903
620701902
620701901
621701903
620701902
620701901
621701903
620701902
620701901
621701903
2–4
2–4
2–4
11. Nylon Washer
621701903
Dispenser
DF 100/150
(Gray)
DF/ED 150
(Gray)
DF/ED 175
(Gray)
DF/ED 2XX
(Gray)
DF/ED 300
(Gray)
Kit Number
Components
1.Lid Assembly
2. Cover
629087935
629087931
629087934
629087933
629087928
Qty
1
620027505
52933
620046012
620043511
620037007
631500109
22127
620046011
620043511
620037007
631500109
22127
15276
15210
52970
52964
1
3. Ice Baffle
4. Bin–Stat Kit
5. Bracket
620037007
631500109
620027306
70217
620037003
631500109
22127
620042919
631500116
22127
1
1
2
6. Screw, Mounting
7. Gasket
70217
70217
70217
70217
6–8
87”
1
620050102
90221
620050102
90221
620050102
90221
620050102
90221
620050102
90221
8. Label
9. Acorn Nut, Nylon 620701902
10. Sealing Washer 620701901
620701902
620701901
621701903
620701902
620701901
621701903
620701902
620701901
621701903
620701902
620701901
621701903
2–4
2–4
2–4
11. Nylon Washer
621701903
January 13, 2002
EIMI Cornelius Inc; 2001–03
Download from Www.Somanuals.com. All Manuals Search And Download.
Revision D
620919549
7. Gasket
8. Label
620050102
90221
620050102
90221
620050102
90221
620050102
90221
620050102
90221
103”
1
9. Acorn Nut, Nylon 620701902
10. Sealing Washer 620701901
620701902
620701901
621701903
620701902
620701901
621701903
620701902
620701901
621701903
620701902
620701901
621701903
2–4
2–4
2–4
11. Nylon Washer
621701903
IMPORTANT: For DF/ED300 models, adjust the automatic agitation timer located in the dispenser’s
electrical control box to 5 seconds on, 20 minutes off. Access to the timer is provided by removing the
merchandiser/upper front panel.
1. Unpack kit. Refer to Figures 1 and 2 for component detail.
2. Insert the ice baffle (item 3) into the lid assembly (item1) (Figures 1).
IMPORTANT: The baffle prevents ice from over–filling the manual fill area during agitation/dispensing with
a full storage bin and forcing the manual fill cover off.
3. Place the sealing washers (item 10) over the studs and flat washers (item 11) then fasten in place with the
nylon acorn nuts (item 9).
4. Set the lid assembly onto the dispenser. Using the slotted holes on the side of the lid as a template, drill four
(4) 9/64” diameter holes at the bottom of the slots (Figure 2).
Note: Use extreme care not to drill into the hopper. Use a drill stop to ensure that the drill bit does not
penetrate deeper than ¼” past the sheet metal. Failure to do so could result in a hole in the hopper, great-
ly reducing the efficiency of both the dispenser and ice maker.
5. Fasten the lid to the dispenser with four (4) #8 sheet metal screws (item 6), two on each side.
6. Seal the ice maker to the top of the dispenser as follows:
A. Remove the ice maker front panel.
B. Position the ice maker base on the gasket (item 7) located on the lid assembly.
IMPORTANT: Do not slide the ice maker into position on the lid.
C. Lift and set the ice maker base onto the lid to avoid damaging the gasket seal.
7. Install the brackets (item 5) on either the rear corners or on the back of the ice maker, using the brackets as
a template. Use care not to drill into any ice maker components (condenser, tubing, etc.) or into the ice hop-
per. Be sure to overlap the lid assembly with the brackets, installing screws in both the lid assembly and ice
maker.
8. Install the wireform bracket supplied with the bin–stat kit (item 4) through the 5/8” diameter hole in the bottom
of the ice maker, wrapping the eye of the wireform over the stud near the hole in the ice maker and secure
with the 8–32 nut provided (Figure 3). Feed the bin–stat cap tube through the hole to the end of the wireform
bracket and wrap the tube around the end of the bracket several times , insuring that the tube is secure.
Note: The bin–stat must not interfere with the agitator rotation not be in the path of the ice falling from the
ice maker. If so, bend the bracket out of the way.
9. Apply the label (item 8) on the front of the cover.
January 13, 2002
Revision D
620919549
EIMI Cornelius Inc; 2001–03
Download from Www.Somanuals.com. All Manuals Search And Download.
9
11
10
SECTION Z–Z
SCALE 0.500
2X
9
11
2X
10
2X
3
NOTE: NOT ALL PARTS ARE SHOWN FOR CLARITY.
FIGURE 1. PARTS
January 13, 2002
Revision D
620919549
EIMI Cornelius Inc; 2001–03
Download from Www.Somanuals.com. All Manuals Search And Download.
DRILL ø9/64 (.140) HOLES
USING BOTTOM OF SLOTTED
HOLES AS A TEMPLATE.
ICEMAKER
NOTE: SET THE ICEMAKER ONTO THE GASKET.
DO NOT SLIDE THE ICEMAKER INTO POSITION
ON THE LID.
VIEW Y
SCALE
0.500
5
P/N 620027306
5
P/N 620027306
8
1
2
6
8X
7
5
P/N 22127
2X
4X
6
6
2X
SEE VIEW Y
FIGURE 2. DISPENSER ASSEMBLY
NOTE: ITEM 5–USE EITHER P/N 620027306
OR P/N 22127
January 13, 2002
Revision D
620919549
EIMI Cornelius Inc; 2001–03
Download from Www.Somanuals.com. All Manuals Search And Download.
January 13, 2002
Revision D
620919549
EIMI Cornelius Inc; 2001–03
Download from Www.Somanuals.com. All Manuals Search And Download.
|