Cooper Lighting Landscape Lighting J FE CF 03 User Manual

Installation Instructions  
Sheet 1 of 2  
Large, OUTDOOR  
YR (30 1/2")  
(Yoke mount, Remote ballast)  
Visor and Non-Visor  
Warning: Before starting any work ensure  
that all sources of power are turned off. All  
work must meet local/national codes and be  
performed by a certified electrician. Do not  
mount fixtures vertically.  
Vault  
C-Scroll  
Roundel  
These installation instructions are valid with the above Ametrix styles.  
Exploded view and part call-out  
Mounting yoke to outdoor surface  
1
Outdoor J-box  
(by others)  
#6-32 x 1/2  
Socket cap screw 1/2" Compression  
(x2) fitting  
Yoke end cap  
Yoke  
#6-32 x 1/4  
screw(x2)  
Yoke end cap  
Yoke end cap  
#10-32 x 5/8  
End screw (x2)  
1/4 Fasteners  
(by others) (x4)  
1. To secure yoke to outdoor surface, the fixture head must be  
removed. First, remove both #10-32 x 5/8 end screws.  
2. Remove one #6-32 x 1/4 screw to remove yoke end cap and  
fixture head. Place both fixture head and yoke end cap in a  
safe place.  
3. With fixture head and yoke end cap safely stored, secure  
yoke to outdoor surface using four(4) appropriate 1/4"  
#10-32 x1  
End screw  
#6-32 x 1/4  
#6-32 x 5/8  
Socket cap screw  
(x3)  
Screw (x2)  
1/4" Fasteners  
(by others)  
Fixture head  
fasteners (by others).  
2
3
Wiring and sealing outdoor fixture  
Aiming the fixture  
#6-32 x 1/2  
Socket cap screw  
(x2)  
#10-32 x 5/8  
end screws  
1/2" Compression  
fitting  
Fixture head  
indicator  
#6-32 x 5/8  
Socket cap screw  
(x3)  
40  
Yoke arm indicator  
1. To seal fixture head, after installing lamp, all screws and  
latches must be secured on door face. Holes above latches  
receive the #6-32 x 1/2 socket cap screws. The center hole(s)  
receive the longer #6-32 x 5/8 socket cap screw.  
2. Slide 1/2" compression fitting down fixture head wire and  
splice wit power feed, ensuring all connections are properly  
matched. Seal 1/2" compression fitting to outdoor surface and  
ensure a watertight seal.  
1. To aim fixture, loosen both #10-32 x.625 end screws. When  
the PointGrabTM system indicators are lined up, the slope  
of the lens face is 40-degrees. Each subsequent notch is  
an additional 10-degrees.  
2. When the fixture head is adjusted to the desired angle, re-  
tighten end screws to secure the position.  
ADY071449 Rev A (ECN070295)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Clover Electronics Digital Camera HDC150 User Manual
Compaq Computer Accessories AA RH8RD TE User Manual
Conair Scale WW33D User Manual
Crate Amplifiers Musical Instrument Amplifier KX 50 User Manual
Delta Electronics Power Supply Series L36SA User Manual
Dynaudio DVD VCR Combo Evidence User Manual
Everpure Water System EV9272 22 User Manual
Fostex Cable Box COP 1 96K User Manual
Generac Power Systems Portable Generator 04389 3 04456 3 04390 3 User Manual
Gigabyte Network Card GN A11G User Manual