Coleman Tent 2000001597 User Manual

®
WEATHERMASTER 6 SCREENED TENT  
MODEL 2000001597  
Before you begin  
6. Rotate all eight Leg Poles upright and insert  
Read all instructions before set up.  
pin on each web loop at the side locations  
7A  
• Select a level site clear of rocks, branches, and other hard or sharp  
objects, to install your tent.  
as shown. (Fig. 7 & 7A)  
Pin  
WARNING: Keep clear of overhead power lines.  
• Do not set up your tent under trees because of potential lightning strikes  
or falling tree limbs in inclement weather.  
• Secure with all stakes and guylines provided to prevent property damage  
or personal injury.  
• For best results in windy conditions, position narrow end of tent into  
the wind.  
• Enlist the help of at least one other person to assist you when it is time  
to assemble the tent.  
Pole Descriptions  
Pole  
Pole  
Pole  
Fig. 7  
Description  
Qty. Dia.  
Repair Kit Replacement Kit  
7. Locate the plastic hooks at sides and  
corners of tent, then snap onto Leg  
Poles to attach. (Fig. 8)  
Long Leg Pole, steel  
(w/ red marking)  
Short Leg Pole, steel  
Curved Ridge Pole, steel  
(w/ red marking)  
Curved Ridge Pole, steel  
Awning Pole, black,  
fiberglass, metal tips  
Door Pole, long, thin, black,  
fiberglass, rubber tips  
Vert. Door Pole, short, black,  
fiberglass, rubber tips  
4
4
19mm  
19mm  
N/A  
N/A  
5010000608  
5010000610  
2
2
19mm  
19mm  
N/A  
N/A  
5010000607  
5010000609  
Fig. 8  
Fig. 9  
8. To stretch tent to finished size:  
• Push in button on Leg Pole while  
twisting lower Leg Pole section  
counterclockwise (Fig.9);  
1
1
1
6.3mm 5010000543 5010000545  
6.3mm 5010000543 5010000545  
6.3mm 5010000543 5010000545  
Upper  
Leg Pole  
Section  
• Pull up on top Leg Pole section  
until tent is taut;  
• Twist the lower Leg Pole clock-  
wise until the button locks into  
the center or lowest hole;  
Button  
Center Hole  
Lower Hole  
To Set Up Tent  
1. Unfold tent and spread out on a clean, level surface with the  
Lower  
door facing the desired direction. Unzip doors. (Fig. 1)  
Leg Pole  
Section  
Fig. 1  
• Repeat on remaining Leg Poles.  
9. Insert plastic stakes through web  
straps located on both sides of tent,  
then drive in to secure. (Fig. 10)  
Door  
NOTE: It may be necessary to remove  
metal stakes through web straps at  
side of tent and screen room, pull tent  
taut, and drive in stakes to secure.  
2. Pull four corners of tent taut, then secure by  
driving stakes through web loops at an angle  
for better anchoring. (Fig. 2)  
Fig. 10  
Fig. 2  
3. Assemble four, steel, shock-corded,  
curved Ridge Poles. Insert Ridge Poles  
(with red marking) into center sleeves  
on top of tent with the red trim (Fig. 3).  
Insert the remaining curved Ridge Poles  
into the other two sleeves on top of tent.  
Fig. 3  
Hinged, Rigid Door  
Ridge Pole  
with Red  
Marking  
1. Assemble Vertical Door Pole (shorter black pole with plastic  
cap tips); then insert through zippered vertical pole sleeveon  
hinged side of door. (Fig. 11)  
Sleeve  
with Red  
Trim  
2. Insert end of Vertical Door Pole into bottom hinge plate,  
apply pressure to form a slight bow, then insert other tip of  
pole into top hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)  
3. Assemble Door Pole (longer black pole with plastic cap tips);  
then insert into zippered pole sleeve at top of door. (Fig. 14)  
4. Insert end of Door Pole into top hinge plate, apply pressure  
to form a bow, then insert other tip of pole into the bottom  
hinge. (Fig. 15)  
4. Assemble eight, steel, shock-corded, Leg Poles. Push down  
on steel button on tapered end and insert into end with  
four holes.  
NOTE: Make sure steel button locks  
into third hole on pole as shown. (Fig.4)  
5. Insert curved end of Leg Poles  
Button in third hole  
Fig. 4  
(with red marking) into the ends of the  
Ridge Poles (with red  
marking). Insert curved  
end of remaining short  
5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)  
Fig. 11  
Fig. 12  
Fig. 13  
Ridge Pole with  
Red Marking  
Vertical Pole  
Sleeve  
Leg Poles into the ends  
of the remaining Ridge  
Poles. (Fig. 5 & 6)  
Door Hinge  
Sleeve  
with Red  
Trim  
Curved End of  
Long Leg Pole  
Fig. 5  
Fig. 6  
Fig. 15  
Fig. 14  
Curved Ridge  
Poles with Red  
Marking in  
center 2  
Top  
Door  
Pole  
Sleeve  
Hinge  
sleeves  
Fig. 16  
(continued on other side)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Contec Stud Sensor CS2000 User Manual
Craftsman Lawn Mower 37654 User Manual
Craftsman Lawn Mower 91725693 User Manual
Cuisinart Toaster CPT 120 Series User Manual
Dacor Double Oven EORX230 User Manual
Dacor Oven ECD ECS User Manual
Fisher Paykel Ventilation Hood HT90DBX1 User Manual
GE Monogram Microwave Oven ZEM200BF User Manual
Genesis ICE Cordless Drill GCD18BK User Manual
GE VCR VGN550 User Manual