OWNER’S MANUAL
C P - 7 2 0
®
INTENNA
C O R D L E S S
T E LE P H O N E
C o b r a Ele c t r o n ic s C o r p o r a t io n
6 5 0 0 W . C o rt la n d S t re e t
C h ic a g o , IL 6 0 6 3 5
®
PRINTED IN HONG KONG
©COBRA ELECTRONICS CORPORATION 1997
480-102-P-001
Download from Www.Somanuals.com. All Manuals Search And Download.
When using your telephone equipment,
basic safety precautions should always be
followed to reduce the risk of fire, electric
shock and injury to persons, including the
following:
product through cabinet slots as they
may touch dangerous voltage points or
short out parts that could result in a risk
of fire or electric shock. Never spill liquid
of any kind on the product.
The cordless handset operates on batteries.
CAUTION:To reduce the risk of fire or
personal injury, read and follow these
instructions:
A. Use only the battery pack supplied
with the unit or identical replacement.
B. Do not dispose of battery pack in a
fire. The cells may explode. Check
with local codes for possible disposal
instruction.
C. Since released electrolyte is corrosive
and may cause damage to eyes or
skin and may be toxic if swallowed:
1. Read and understand all instructions.
11. To reduce the risk of electric shock, do
not disassemble this product, but take it
to qualified servicemen when service or
repair work is required. Opening or
removing covers may expose you to
dangerous voltages or other risks.
Incorrect reassembly can cause electric
shock when the appliance is
2. Follow all warnings and instructions
marked on the product.
IMPORTANT
SAFETY
INSTRUCTIONS
3. Unplug this product from the wall outlet
before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
subsequently used.
C1. Do not open or mutilate battery
pack.
C2. Always replace the entire battery
pack rather than reusing one or
more cells.
4. Do not locate base unit near water, for
example, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet
basement or near a swimming pool.
12. Avoid using telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
5. Do not place this product on an unstable
cart, stand or table. The product may fall,
causing serious damage to the product.
13. Do not use the telephone to report a
gas leak in the vicinity of the leak.
14. Unplug this product from the wall outlet
and refer servicing to qualified service
personnel under the following
conditions:
C3. Do not expose batteries to heat or
flame.
D. Exercise care in handling the battery
pack in order not to “short” the
battery contacts with conducting
materials such as rings, bracelets, and
keys. The battery or conductor may
overheat and cause burns.
6. Slots and openings in the cabinet and
the bottom or back are provided for
ventilation, to protect it from
5
A. When the power supply cord or plug
is damaged or frayed.
B. If liquid has been spilled into the
product.
C. If the product has been exposed to
rain or water.
D. If the product does not operate
normally by following the operating
instructions. Adjust only those
controls that are covered by the
operating instructions because
improper adjustment of other
controls may result in damage and
will often require extensive work by a
qualified technician to restore the
product to normal operation.
E. If the product has been dropped or
the cabinet has been damaged.
F. If the product exhibits a distinct
change in performance.
overheating; these openings must not
be blocked or covered. The openings
should never be blocked by placing the
product in the bed, sofa, rug or other
similar surface. This product should
never be placed near or over a radiator
or heat register. This product should not
be placed in a built-in installation unless
proper ventilation is provided.
15. Never install telephone wiring during a
lightning storm.
16. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
17. Never touch uninsulated telephone wires
or terminals unless the telephone line has
been disconnected at the network
interface.
18. Use caution when installing or modifying
telephone lines.
7. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure
of the type of power supply to your
home, consult your dealer or local power
company.
P o w e r S u p p ly S p e c if ic a t io n s
This symbol signifies that only the Cobra AC
Adapter supplied with this cordless telephone
(Part No. 768-021-N-001) should be used
Input: AC 120V, 60Hz, 4W
8. Do not allow anything to rest on the
power cord. Do not locate this product
where the cord will be abused by
persons walking on it.
Output: DC 12V, 400mA
!
9. Do not overload outlets and extension
cords as this can result in the risk of fire
or electric shock.
SAVE THESE INSTRUCTIONS
®
10. Never push objects of any kind into this
Cobra
C P -7 2 0
N EED H ELP ?
1 -7 7 3 -8 8 9 -3 0 8 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SOME THINGS YOU NEED TO
number s int o t he digit al
memor y syst em and r et r ieve
t hem j ust by pr essing a
but t on or t wo. For
addit ional inf or mat ion,
s e e pa ge s 10 & 11.
KNOW BEFORE YOU GET STARTED
Now that your new Cobra Intenna is out of
the box and ready to use, here are some
things you’ll need to be aware of before
getting started.
DID YOU
KNOW THAT...
Lo c a t io n
Be sure the location you‘ve chosen is near
both an electrical outlet and a telephone
jack—both are required to connect your
new Cobra Intenna. Maximum range is
obtained by locating the base as high as
possible in your home.
◆
You can sel ect f r om
any one of t he
10 CHANNELS
You can REPLACE THE
BATTERIES in t he
handset your sel f . It ’s f ast
and easy. Se e pa ge 18
f or simpl e-t o-f ol l ow
inst r uct ions.
C h a r g in g
AVAILABLE any t ime you
wish by pr essing a but t on.
If t he channel you’r e using
get s t oo much noise or
st at ic, pick a cl eaner one,
wit hout disconnect ing your
cal l . Se e pa ge 14 f or
mor e det ail s.
After connecting, and before using the
handset of your new system, it will need to
rest in the base overnight (at least 12 hours)
in order to charge.
R in g e r
1
Make sure the RINGER switches (one
for handset and one for base), located
7
RINGER
◆
on the side of the base, are set to ON.
1
P u ls e / To n e
Your new Cobr a Int enna
Cor dl ess Tel ephone has a
t r ue TWO-WAY
INTERCOM buil t in. You
can page f r om t he base or
t he handset , use t he
int er com as a baby
monit or —even use it t o
l ocat e a mispl aced handset .
For det ail s, see pa ge s 12
& 13.
2
Set the PULSE/TONE switch, located
on the rear of the base, to the operation
◆
PULSE/
TONE
2
that is correct for your installation—see
page 15 for additional information.
Your handset is HEARING
AID COMPATIBLE
(HAC) which means t hat
it ’s special l y designed t o
act ivat e and enhance t he
sound qual it y of your
hear ing aid syst em. For
mor e det ail s on how t his
can wor k f or you, s e e
pa ge 16.
Ke e p Th is G u id e
Put this guide in a handy place. You may
want to refer to it for information when
using or programming different features of
your Cobra Intenna Cordless Telephone.
ALL YOU HAVE TO DO TO IS PLUG IT IN
Plug the adapter cord into the power jack on
the rear of the base, then plug the adapter
into any standard 110V outlet.
This syst em has MEMORY
DIALING. You can
pr ogr am 32 of your most
f r equent l y cal l ed phone
S e t t h e h a n d s e t o n t h e b a s e a n d le t it
c h a r g e o v e r n ig h t . M a k e s u r e t h e
C H A R G E in d ic a t o r o n t h e b a s e lig h t s .
C o n n e c t t h e p h o n e c o r d a n d in 1 2 h o u r s
y o u ’r e r e a d y t o m a k e a n d r e c e iv e c a lls .
®
Cobra
C P -7 2 0
N EED H ELP ?
1 -7 7 3 -8 8 9 -3 0 8 7
Download from Www.Somanuals.com. All Manuals Search And Download.
WALL MOUNTING
USING YOUR COBRA
INTENNA CORDLESS PHONE
O n A P la t e
Your Cobra Intenna is designed to be used
with AT&T, GTE or any other wall-mounting
plates that may be purchased from most
local electronics or home repair stores.
Now that the handset batteries have
charged overnight (at least 12 hours) your
Cobra Intenna Cordless Phone is ready to
use.
2
1. Press the telephone cord into the slots
under the base and wrap it around the
cord storage area as shown.
To A n s w e r A C a ll A t Th e
B a s e
2. Plug the phone connector into the
telephone wall jack.
2
When the phone rings, simply pick up
the handset from the base and the
TALK button will automatically light.
When you hang up, it disconnects.
TALK
3. Plug the power adapter into the
telephone base and a nearby AC
power outlet.
4.To hang the phone base, simply align
the holes on the bottom of the base
with the studs on the wall plate and
slide the base down until it locks into
place.
To P la c e A C a ll A t Th e B a s e
2
Pick up the handset from the base,
then press and release the TALK button.
TALK
When you hear the dial tone, place your
call.
5. Pull cradle hook to correct position to
hold handset.
9
1
CRADLE
HOOK
D ir e c t ly O n Th e W a ll
To A n s w e r o r P la c e A C a ll
A w a y Fr o m Th e B a s e
To install the base directly on any wall, you’ll
need two screws and wall anchors (not
included).
2
The TALK button must be off (not lit)
when the handset is away from the
TALK
base and not in use. Press and release
the TALK button and, when your
conversation is finished, press the TALK
button again to disconnect. If you
replace the handset in the base, the
TALK button will disconnect
1. Drill two holes aligned vertically, one
31⁄4" higher than the other, and insert
the wall anchors.
2. Drive the screws into the anchors until
the head of each screw sticks out
about 1⁄8" from the wall.
1
automatically.
3. Plug the phone connector into the
telephone wall jack.
To A n s w e r A C a ll
A t Th e B a s e U s in g
Th e S p e a k e r p h o n e
4. Plug the power adapter into the
telephone base and a nearby AC
power outlet.
3
Press the SPEAKERPHONE button. See
page 13 for details.
5. To hang the phone base, simply align
the holes on the bottom of the base
with the screws on the wall and slide
the base down until it locks into place.
SPEAKER-
PHONE
3
6. Pull cradle hook to correct position to
hold handset
1
CRADLE
HOOK
®
Cobra
C P -7 2 0
N EED H ELP ?
1 -7 7 3 -8 8 9 -3 0 8 7
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE MEMORY
DIALING FEATURE
positions. Be sure to note the names
for each number you are storing, so
you can create your directory card
when you are finished.
when your call goes through for hands-free
communication, or pick up the cordless
handset and press TALK for mobility.
Memory dialing lets you store and dial 32
commonly-called telephone numbers
automatically, just by pressing a button.No
more fumbling with the phone book,
guessing at numbers or accidentally
misdialing the people you call most.
5
To S t o r e A N u m b e r
Lo n g e r Th a n 1 6 D ig it s
To D ia l A N u m b e r S t o r e d In
M e m o r y Fr o m t h e H a n d s e t
For telephone banking or alternate long
distance service, you may need to program
a number that is longer than 16 digits. To do
so, you will need to divide the number
between two different memory locations.
Example: Store an alternate long distance
acces number in location 1 and personal
identification number for that service in
location 2.
If you are away from the base where
5
the written directory is stored, you will
have to remember the directory storage
number for the call you wish to make.
TALK
To S t o r e A N u m b e r In M e m o r y
U s in g t h e B a s e Ke y p a d :
6
1. Press TALK for dial tone.
2. Press MEMORY button.
6
In order to accomodate 32 numbers, your
memory system is designed with 16
buttons which control both upper (1-16) and
lower (17-32) banks of memory numbers. A
red LED (light-emitting diode) lights to show
you are using either upper or lower bank. To
switch banks, press the button next to the
LED marked “Lower”.
MEMORY
3. Enter the directory storage number
(01-32) for the call you wish to make
(you must enter 0 before numbers 1-
9 in order to access the memory
number from the handset); the
C r e a t in g A D ir e c t o r y
As you are programming the memory bank,
you will want to keep track of whose
number will be dialed automatically.
number you are assigning to each location.
When finished, you may indicate who is
assigned to each number by filling in the
directory located on the base. This provides
a quick and easy reference. To create the
directory, remove the protective plastic
cover by sliding it gently toward the middle
and lifting it out. Fill in the names on the
directory next to the number they have
been assigned and replace the cover.
To p r o g r a m n u m b e r s
in t o t h e m e m o r y b a n k
f r o m t h e b a s e :
1
To R e p la c e O r C h a n g e A
N u m b e r S t o r e d In M e m o r y
11
Simply repeat the steps under “To Store A
Number In Memory”. The new number will
automatically replace the previous number
stored. Be sure the red LED indicator is set
on the correct memory bank.
1. Make sure the LED for the bank you
SWITCH
BUTTON
want (“Upper” or “Lower”) is lit. If
not, press the button next to the
“Lower” LED until the correct LED
lights.
2
1
LOWER
P e r m a n e n t M e m o r y C ir c u it
LED
2. Press the button for the memory
Your Cobra Intenna provides you with a
permanent memory circuit; even if you
disconnect the AC power or experience a
power outage, don’t worry-- your memory
bank will remain programmed
location you wish to program. You
To D ia l A N u m b e r S t o r e d In
M e m o r y Fr o m B a s e Ke y p a d
U s in g S p e a k e r p h o n e
2
3
will hear a beep and the LED will
flash to let you know it is ready to
store a number. You have 10 seconds
to begin programming the number (if
10 seconds elapses without digits
being entered, the LED will stop
flashing, you will hear a long beep
and the LED will light steadily again).
3
UPPER
LED
1. Be sure the proper memory bank is
in use (LED is lit) for the call you wish
to place. If not, press the button next
to “Lower” LED until either “Upper”
or “Lower” LED is lit.
1
SWITCH
BUTTON
2
3. Enter the number you wish to store
(up to 16 digits).
2. Press SPEAKERPHONE button to
get a dial tone. Speakerphone LED
lights to tell you the speakerphone is
in use.
LOWER
LED
4. Press the same memory button
again. You will hear two double
beeps to confirm the number is
stored. If you hear three beeps
instead, you may have pressed the
incorrect storage button, and you’ll
need to repeat the steps above.
3
UPPER
LED
3. Press the storage button next to the
name of the location you wish to call.
The number is dialed automatically.
4
You may continue using speakerphone
SPEAKER-
PHONE
5. Repeat the above steps for up to 32
®
Cobra
C P -7 2 0
N EED H ELP ?
1 -7 7 3 -8 8 9 -3 0 8 7
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE BUILT-IN
INTERCOM/PAGING SYSTEM
4. If someone tries to reach you on the
Intercom while you are talking on the
handset, you will hear three rings.
Press HOLD, then INTCM on the
handset. (The base will beep and
speakerphone will activate.
Speakerphone LED will flash when
there is a call on hold). Your caller will
then be put on hold while you
answer the INTCM. The TALK button
will flash to remind you that you have
a call on hold. Press TALK again to
disconnect the INTCM and
To U s e Th e P a g e r
A s A H a n d s e t Lo c a t o r
Call Dad to dinner, monitor the baby while
you do laundry or keep an ear out to make
sure that the children aren’t hurt. These
options, along with many others, are at your
fingertips with your Cobra Intenna because
it doubles as a two-way intercom/paging
system between the base and the
handset—and outside calls will still come
through! If you should misplace the
handset, simply activate the pager and
follow the signal until you locate it.
5
1
3
2
HOLD
1. To locate a misplaced handset around
the home, press and release the
INTERCOM button on the base.
INTERCOM
1
INTCM
2. The handset will sound a series of
three beeps for 30 seconds, giving
you time to locate it. Once found,
press and release the INTCM button
on the handset to eliminate the
signal.
1
INTCM
5
3
TALK
To U s e Th e In t e r c o m / P a g e r
reconnect with your telephone call.
1
1. If you are at the handset and wish to
speak with someone at the base,
INTCM
3. If you have not located the handset
in 30 seconds, repeat steps above.
press and release INTCM which will
sound three rings and light the red
indicator next to the INTERCOM
To U s e Th e In t e r c o m
A s A M o n it o r
2
INTERCOM
1
button on the base. The person may
then respond just by speaking into
the base. To end the conversation,
simply press the INTCM button on
the handset again.
Monitor the room in which the base is
located from another location using the
Intercom feature.
INTCM
1 3
USING THE SPEAKERPHONE
1. Press INTCM button on the handset.
This engages the itercom
2. If you are at the base and wish to
page someone at the handset, press
and release INTERCOM, which will
sound a series of three beeps and
light the INTCM button on the
handset. The person may then
respond by pressing INTCM and
speaking into the handset.
Whether you’re conducting a business
meeting or want to let everyone in the
family hear and talk when grandma calls to
say “hello”, nothing beats the convenience
of our new speakerphone.
microphone in the base, allowing you
to listen to the base location area.
2. Listen through the handset for as
long as you like.
To U s e Th e S p e a k e r p h o n e
4
3. Disconnect by pressing INTCM
again.
1
After your call is connected, simply
2
SPEAKER-
INTCM
3. If you receive a call during an
press the button on the base next to
PHONE
3
intercom conversation, you will hear
a low volume ringing. If you are at
the handset, press TALK, which will
disconnect the intercom and connect
you with the incoming call. If you are
SPEAKERPHONE and the red LED will
light, indicating that the speakerphone
is on. If desired, one person may
continue to speak through the handset
while connected. Press the button
again to disconnect.
4. If you receive an incoming call while
you are using the monitor, you will
hear a ringing in the handset.
TALK
4
5. Press TALK to connect the call. The
Intercom is automatically
disconnected.
at the base, press SPEAKERPHONE.
3
SPEAKER-
PHONE
TALK
4
®
Cobra
C P -7 2 0
N EED H ELP ?
1 -7 7 3 -8 8 9 -3 0 8 7
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL FEATURES OF YOUR NEW COBRA INTENNA
CORDLESS TELEPHONE WITH 32 NUMBER MEMORY
Redial feature will try the call again in 60
seconds, up to 10 times. When the call is
answered, press SPEAKERPHONE to be
connected. If you decide to call another
number, the Auto Redial for the previous
number will be cancelled. To disconnect the
Auto Redial feature, press the AUTO
REDIAL button again (Speakerphone LED
will go out).
■ B A T T E R Y S A V E R
■ D IG ITA L S E C U R IT Y
Aside from the features that have already
been outlined, your Cobra Intenna is easier
to program and use than ever before
because many of the features you want
most are built right in—You don’t have to do
a thing!
The handset may be positioned away from
the base without losing power for up to 7
days, depending upon how often you use it.
Cobra suggests that you regularly leave the
handset in the base (for example, overnight)
when not in use to keep your handset
battery from losing its charge. The battery
will not overcharge, even though the
Your Cobra Intenna is manufactured with
65,000 randomly generated security codes
to guard against accidental or intentional
eavesdropping on your private
conversations.
■ ILLU M IN A T E D K E Y P A D
■ B U ILT- IN A N T E N N A
CHARGE indicator light remains on.
When the phone rings or you touch any
button, the keypad automatically lights up,
making it easy to read and use, even in the
darkest room or late at night.
There’s no unsightly antenna to extend,
nothing to get bent or broken or possibly
even cause physical harm, because
antennas are built into the handset and
base. That, along with our Clear Call® PLUS
Compander Noise Reduction system which
minimizes background noise and
interference for optimum audio
performance, makes the Intenna quality
comparable to a standard corded phone.
■ H E A R IN G A ID
C O M P A T IB LE (H A C )
■ P U LS E / T O N E S W IT C H
Your Cobra Intenna handset is specially
designed to be compatible with standard
hearing aid systems.
Your Cobra Intenna may be set to either
PULSE orTONE, (depending upon your
phone system) by moving the switch
located on the back of the base. Mixed
PULSE and TONE dialing may be used
(when you have a PULSE system and need
to access certain long-distance or
computerized banking services) by keeping
the base switch to PULSE and pressing the
TONE button on the handset to temporarily
switch to TONE. Hanging up resets to
PULSE.
■ E LE C T R O N IC H O LD
Save time and steps in houses with more
than one telephone. After you put a call on
hold, your Intenna automatically releases
when you, or someone else, picks up
another handset on the same line. No need
to come back and turn it off, because it
turns itself off automatically.
■ F LA S H B U T T O N
1 5
Press and release the FLASH button to
briefly interrupt the phone line and, if you
subscribe, access some of the advanced
options like “Call Waiting” or “Three Way
Calling” that may be offered by your
telephone company.
■ S C R A M B LE D S IG N A LS
Although you may not realize it, other
people with cordless phones, scanners or
even baby monitors may be listening in on
your conversations. This is especially
disturbing when discussing personal
information such as credit card numbers,
vacation plans, etc. over the phone. Cobra’s
PRIVATE CALL™ voice scrambler eliminates
that worry forever!
■ LA S T N U M B E R R E D IA L
(f r o m h a n d s e t o n l y )
■ H A N D S E T A N D B A S E
■ R IN G E R S W IT C H F O R
Reached a busy number? Press FLASH to
get a new dial tone, then press REDIAL
button and the last number called will be
redialed for you.
V O LU M E C O N T R O LS
H A N D S E T O R B A S E
Gradually change the volume of your caller’s
voice from low to high or high to low by
pressing the volume control up/down
button located on the side of your handset.
You may do the same for the speakerphone
by using the up/down button located on the
base. Adjust to 3 levels from the handset
and 16 levels from the base.
You’re taking a nap, watching your favorite
TV show or just got the baby to sleep and
don’t want to be disturbed. Temporarily turn
off the ringer on the handset, the base or
both by moving the switch on the side of
the base into the off position.
■ A U T O M A T IC LA S T
N U M B E R R E D IA L
(f r o m s p e a k e r p h o n e
o n b a s e o n l y )
■ 1 0 - C H A N N E L
R E C E P T IO N
Your Cobra Intenna automatically scans
through 10 channels every time you pick up
the handset, to offer you the clearest, noise-
free connection available. Should
interference occur during a conversation,
simply press and release the CHANNEL
button until you reach a clear channel.
■ 2 - P O S IT IO N H A N D S E T
You’re getting a busy signal but need to get
through as soon as possible. No problem.
When the number you’ve dialed is busy,
disconnect from the speakerphone by
pressing SPEAKERPHONE button, the
press AUTO REDIAL button. The number
will redial and the Speakerphone LED will
flash. If the number is still busy, the Auto
Handset may be positioned lying down or
upright. However,it will not charge in the
base when standing upright.
■ O U T- O F - R A N G E S IG N A L
When you press the TALK button and
immediately hear three beeps, you know
your handset is too far away from the base
to work properly. Move closer to the base
and try your call again.
®
Cobra
C P -7 2 0
N EED H ELP ?
1 -7 7 3 -8 8 9 -3 0 8 7
Download from Www.Somanuals.com. All Manuals Search And Download.
RECHARGEABLE BATTERY INFORMATION
R e p la c in g Th e B a t t e r y
To D is p o s e O f Yo u r B a t t e r y
Your Cobra Intenna comes complete with a
rechargeable nickel-cadmium battery
already in the handset. You will need to
charge the battery by plugging in the base,
placing the handset in the base and letting it
charge overnight (at least 12 hours).
If you have recharged the battery for 12
hours or more and the handset does not
work when the TALK button is pressed, you
may need to replace the battery. To order a
new battery, call Cobra toll-free at 1-773-
889-3087, or remove it from the handset
and take it to a local hardware store or
home center store to be certain that you
are getting the proper replacement battery.
The rechargeable nickel-cadmium (NiCad)
battery in this product must be recycled or
disposed of properly in compliance with all
applicable laws. Certain states or
municipalities require recycling and have
established collection programs. Please
contact your local waste removal authority
for instruction or return to Cobra for
recycling. Wrap carefully and mail postage
prepaid to:
B a t t e r y R e c h a r g in g
There are three things that can happen to
indicate that your handset battery needs
recharging. When one of these three things
occurs, you will need to return the handset
to the base and recharge for at least 12
continuous hours.
To R e m o v e / R e p la c e Th e
H a n d s e t B a t t e r y
1
1. To remove the battery door, press
and slide downward.
1. The TALK button on the handset
flashes.
2. Carefully disconnect the battery pack
and dispose of it properly. See
BATTERY DISPOSAL below.
C O B R A E LE C T R O N IC S
C O R P O R A T IO N
1 7
2. A 2-beep warning sounds while you
are using the phone. This indicates
that you have just a few minutes of
power left to complete your
conversation before the phone
disconnects.
1
6 5 0 0 W . C o r t la n d S t r e e t
C h ic a g o , Il. 6 0 6 3 5
3. To replace, connect the new battery
and replace the door. Return the
handset to the base and charge the
battery overnight (at least 12 hours).
A t t n : B a t t e r y R e c y c lin g
D o n o t p u t b a t t e r ie s in t o f ir e o r
e x p o s e t o h ig h h e a t . (lo g o )
Th e y m a y e x p lo d e .
3. The handset beeps at 30 second
intervals for five minutes when it has
been away from the base too long.
After five minutes, it will not flash or
beep, nor will you be able to get a
dial tone. Return the handset to the
base for recharging.
To C le a n Th e
C h a r g in g C o n t a c t s
The two metal charging contacts on both
the handset and the base should be
cleaned regularly with a soft, dry cloth for
optimum recharging performance.
“Contains Nickel-Cadmium
rechargeable batteries. Must be
recycled or disposed of properly”.
NOTE:To prevent your batteries from
running out of power, Cobra suggests that
you leave the handset in the base as much
as possible, when not in use. The CHARGE
indicator will remain on as long as the
handset is in the base, even after the
batteries are fully recharged. This will not
damage the batteries.
Ni-Cd
®
Cobra
C P -7 2 0
N EED H ELP ?
1 -7 7 3 -8 8 9 -3 0 8 7
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED ONE-YEAR WARRANTY
IF YOU THINK YOU NEED SERVICE,
CALL 1-773-889-3087
COBRA ELECTRONICS CORPORATION warrants that its COBRA cordless telephone products,
and the component parts thereof, will be free of defects in workmanship and materials for
period of one (1) year from the date of first consumer purchase. This warranty may be enforced
by the first consumer purchaser, provided that the product is utilized within the U.S.A.
You may be asked to send your unit to the Cobra
factory. It will be necessary to furnish the
following in order to have the product serviced and
returned.
carrier (to avoid loss in transit), such as United
Parcel Service (UPS), Roadway Parcel Service
(RPS) or First Class Insured Mail to: Cobra
Factory Service, Cobra Electronics Corporation,
6500 W. Cortland St., Chicago, IL 60635. Cobra
is not responsible for units not received if
package has not been properly insured.
Cobra will, without charge, repair or replace, at its option defective cordless telephone products
or component parts upon delivery to the Cobra Factory Service Department, accompanied by
proof of the date of first consumer purchase, such as a duplicated copy of a sales receipt.
1. For Warranty Repair include some form of
proof-of-purchase, such as a mechanical
reproduction or carbon or a sales receipt. If you
send the original receipt it cannot be returned.
2. Send the entire product. Must include
telephone handset, base and all cords.
6. If the unit is in warranty upon receipt of your
unit it will either be repaired or exchanged
depending on the model. Please allow
You must pay any initial shipping charges required to ship the product for warranty service. The
return charges will be at Cobra’s expense if the product is repaired or replaced under warranty.
For further details concerning procedures for obtaining service, see the “IfYou Need Service”
section of this Owner’s Manual.
3. Enclose a description of what is happening with
the unit. Include a typed or clearly printed name
and address of where the unit is to be returned.
4. Pack unit securely to prevent damage in transit.
If possible, use the original packing material.
5. Ship prepaid and insured by way of a traceable
approximately 3 to 4 weeks before contacting
us for status. If the unit is out of warranty a
letter will automatically be sent informing you
of the repair charge or replacement charge. If
you have any questions, please call
Exclusions:This limited warranty does not apply 1) to any product damaged by accident,
improper line voltage or weather related circumstances; 2) in the event of misuse or abuse of
the product or as a result of unauthorized alterations or repairs; 3) to non-defective original
equipment Nickel Cadmium rechargeable batteries; 4) if the serial number has been altered,
defaced or removed; or 5) if the owner of the product resides outside the U.S.A.
1-773-889-3087 for assistance.
For technical assistance, please call our Automated Help Desk which can assist you
by answering the most frequently asked questions about Cobra products.
All implied warranties, including warranties of merchantability and fitness for a particular
purpose, are limited in duration to the length of this warranty. Cobra shall not be liable for any
incidental, consequential or other damages, including, without limitation, damages resulting
from loss of use or cost of installation.
1 9
(773) 889-3087
24 hours a day, 7 days a week.
A Consumer Service Representative can be reached through
this same number 8:00 am - 8:00 pm, Monday through Friday, CST.
Technical assistance is also available on-line in the Frequently Asked Question
Some states do not allow limitations on how long an implied warranty lasts and/or do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitations may
not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
REGISTERED WITH THE FCC
Please note:This cordless telephone system
operates in accordance with part 15 and part
68 of FCC rules. Operation is subject to two
conditions: 1) It may not interfere with radio
communications, and 2) It must accept any
interference received, including that which
may cause undesirable operation. See the
Operational Features section of this booklet for
ways to reduce interference.
The FCC requires you to provide information, if
requested by the local telephone company,
about the connection of an FCC registered
telephone to their lines. They may ask you for
the FCC registration number and the ringer
equivalence number (REN), both of which are
on the bottom of the base. They may also ask
for the Universal Service Order Code (USOC)
number, which is RJ-11C.
C O B R A E LE C T R O N IC S
C O R P O R A T IO N
It is illegal to use this phone on a party line or
to connect it to a coin-operated telephone.
6 5 0 0 W . C o r t la n d S t r e e t
C h ic a g o , Il. 6 0 6 3 5
Your telephone company is required by the
Federal Communications Commission to allow
you to connect FCC registered telephones to
their lines.
®
Cobra
C P -7 2 0
N EED H ELP ?
1 -7 7 3 -8 8 9 -3 0 8 7
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
✔
✔
Th e p h o n e is d e a d ; t h e r e a r e n o
in d ic a t o r lig h t s o n .
Are the power cord and telephone cord
properly connected? If so, handset battery
power has run out. Return to base and
charge for 12 or more hours.
FO R YO U R R EFER EN C E, KEEP
A
R EC O R D O F TH E S ER IA L
N U M B ER P R IN TED O N TH E M O D EL LA B EL O N TH E B A S E
COBRA INTENNA
CORDLESS
TELEPHONE
Th e h a n d s e t b e e p s d u r in g
c o n v e r s a t io n o r a w a y f r o m t h e
b a s e .
S ER IA L N O .
The battery needs to recharge. Return to
the base for overnight charging.
✔
✔
Th e TA LK b u t t o n c o n t in u e s
f la s h in g o n t h e h a n d s e t .
TROUBLESHOOTING
CHECKLIST
If y o u r s y s t e m d o e s n o t
o p e r a t e p r o p e r ly, p le a s e
t a k e a m o m e n t t o r u n
t h r o u g h t h is c h e c k lis t a n d
r e f e r t o t h e a p p r o p r ia t e
s e c t io n s o f t h is g u id e .
The battery needs to recharge. Return to
the base for overnight charging.
P o o r s o u n d q u a lit y ; t o o m u c h
in t e r f e r e n c e .
Don’t cover the top section of the handset
with your hand or rest it on your shoulder.
This blocks the internal Intenna. Try
2 1
switching to a different channel, as well.
✔
✔
✔
Th e h a n d s e t d is c o n n e c t s , lo s e s
p e r f o r m a n c e a n d / o r b e e p s
w h e n in u s e a w a y f r o m t h e
b a s e .
If the problem persists,
don’t hesitate to call :
You may be out of range or the battery
needs recharging. Move closer to the base
and/or recharge the battery overnight.
H a n d s e t d o e s n ’t w o r k a f t e r
p o w e r o u t t a g e o r a f t e r
d is c o n n e c t in g a n d
1-773-
r e c o n n e c t in g it .
Return the handset to the base for about
30 seconds to automatically reset the
security code.
889-3087
24 hours a day,
7 days of the week.
We’re here to help.
P o w e r d o e s n ’t s e e m t o b e o n .
Make sure power adapter is properly
connected to a working outlet and the jack
on the back of the answering system.
®
Cobra
C P -7 2 0
N EED H ELP ?
1 -7 7 3 -8 8 9 -3 0 8 7
Download from Www.Somanuals.com. All Manuals Search And Download.
FO LD O VER BO TTO M ED G E A N D TH EN TA P E S ID ES
NOTES
Cobra CP-720 Intenna Cordless Phone Accessories
Description
Part No.
Cost Ea. X Qty. = Amount
NICKEL-CADMIUM BATTERY PACK ASSEMBLY
For use with model CP-720
213-013-N-001
$25.00
AC POWER ADAPTER
For use with model CP-720
(Prices subject to change without notice.)
★★ Illinois residents add 7%
Amount
★★ Cook Co. residents add .75% (7.75% total)
★★ Chicago residents add 1% (8.75% total)
★★ Indiana residents add 5%
★★ Michigan residents add 4 %
★★ Minnesota residents add 6%
★★ Ohio residents add 6%
(Tax if applicable)
Shipping//handling
Total
$3.75
★★ Wisconsin residents add 5%
FO LD H ERE FIRS T
Make check or money order (no stamps) payable to:
Cobra Accessories Dept.
6500 W. Cortland St., Chicago, IL 60707
Call 1-773-889-3087 or FAX 1-773-622-2269 (for credit card orders)
Please print clearly:
Name
Address (Not P.O. Box)
City
State
Zip
Exp. Date
Credit Card No.
Customer Signature
Circle One:
Visa
MasterCard
Discover
Allow 4 to 6 weeks for delivery. Offer valid in Continental U.S. only.
FO LD H ERE
Download from Www.Somanuals.com. All Manuals Search And Download.
|