Cisco Systems Network Router 2821 Series User Manual

Installing and Upgrading Fans in the Cisco 2821  
and Cisco 2851 Series Routers  
This document describes how to install or upgrade fans inside your Cisco 2821 and Cisco 2851 series  
routers.  
This document is intended for the fan installer who is familiar with electronic circuitry and wiring  
practices and has experience as an electronic or electromechanical technician.  
Note  
Use this document in conjunction with the following documents:  
Cisco 2800 Series Hardware Installation guide:  
Cisco 2800 Series and Cisco 3800 Series Integrated Services Routers Regulatory Compliance and  
Safety Information document:  
If you have questions or need help, see the “Obtaining Documentation, Obtaining Support, and Security  
This document contains the following sections:  
Americas Headquarters:  
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA  
© 2008 Cisco Systems, Inc. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Warnings and Guidelines  
Statement 1071—Warning Definition  
Warning  
IMPORTANT SAFETY INSTRUCTIONS  
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you  
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar  
with standard practices for preventing accidents. Use the statement number provided at the end of  
each warning to locate its translation in the translated safety warnings that accompanied this  
device. Statement 1071  
SAVE THESE INSTRUCTIONS  
Waarschuwing  
BELANGRIJKE VEILIGHEIDSINSTRUCTIES  
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan  
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij  
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard  
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de  
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt  
raadplegen.  
BEWAAR DEZE INSTRUCTIES  
Varoitus  
TÄRKEITÄ TURVALLISUUSOHJEITA  
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin  
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu  
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen  
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien  
lausuntonumeroiden avulla.  
SÄILYTÄ NÄMÄ OHJEET  
Attention  
IMPORTANTES INFORMATIONS DE SÉCURITÉ  
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant  
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez  
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures  
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des  
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,  
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.  
CONSERVEZ CES INFORMATIONS  
WICHTIGE SICHERHEITSHINWEISE  
Warnung  
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen  
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und  
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder  
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten  
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.  
BEWAHREN SIE DIESE HINWEISE GUT AUF.  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Warnings and Guidelines  
Avvertenza  
IMPORTANTI ISTRUZIONI SULLA SICUREZZA  
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle  
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli  
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.  
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le  
traduzioni delle avvertenze riportate in questo documento.  
CONSERVARE QUESTE ISTRUZIONI  
Advarsel  
VIKTIGE SIKKERHETSINSTRUKSJONER  
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du  
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med  
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten  
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne  
enheten.  
TA VARE PÅ DISSE INSTRUKSJONENE  
Aviso  
INSTRUÇÕES IMPORTANTES DE SEGURANÇA  
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de  
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos  
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de  
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para  
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.  
GUARDE ESTAS INSTRUÇÕES  
¡Advertencia!  
INSTRUCCIONES IMPORTANTES DE SEGURIDAD  
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular  
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los  
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el  
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña  
a este dispositivo.  
GUARDE ESTAS INSTRUCCIONES  
VIKTIGA SÄKERHETSANVISNINGAR  
Varning!  
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.  
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och  
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av  
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna  
anordning.  
SPARA DESSA ANVISNINGAR  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Warnings and Guidelines  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Warnings and Guidelines  
Aviso  
INSTRUÇÕES IMPORTANTES DE SEGURANÇA  
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões  
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os  
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o  
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de  
segurança traduzidos que acompanham o dispositivo.  
GUARDE ESTAS INSTRUÇÕES  
Advarsel  
VIGTIGE SIKKERHEDSANVISNINGER  
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for  
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de  
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til  
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de  
oversatte advarsler, der fulgte med denne enhed.  
GEM DISSE ANVISNINGER  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Warnings and Guidelines  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Warnings and Guidelines  
Warning  
Do not touch the power supply when the power cord is connected. For systems with a power switch,  
line voltages are present within the power supply even when the power switch is off and the power  
cord is connected. For systems without a power switch, line voltages are present within the power  
supply when the power cord is connected. Statement 4  
Warning  
Warning  
Warning  
Do not work on the system or connect or disconnect cables during periods of lightning activity.  
Statement 1001  
Before opening the chassis, disconnect the telephone-network cables to avoid contact with  
telephone-network voltages. Statement 1041  
Network hazardous voltages are present in the BRI cable. If you detach the BRI cable, detach the end  
away from the router first to avoid possible electric shock. Network hazardous voltages also are  
present on the system card in the area of the BRI port (RJ-45 connector), regardless of when power is  
turned off. Statement 44  
Warning  
Warning  
Before working on a chassis or working near power supplies, unplug the power cord on AC units;  
disconnect the power at the circuit breaker on DC units. Statement 12  
When installing the unit, always make the ground connection first and disconnect it last. Statement 42  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Warnings and Guidelines  
Warning  
Warning  
Before working on equipment that is connected to power lines, remove jewelry (including rings,  
necklaces, and watches). Metal objects will heat up when connected to power and ground and can  
cause serious burns or weld the metal object to the terminals. Statement 43  
Do not touch the power supply when the power cord is connected. For systems with a power switch,  
line voltages are present within the power supply even when the power switch is off and the power  
cord is connected. For systems without a power switch, line voltages are present within the power  
supply when the power cord is connected. Statement 4  
Warning  
Before performing any of the following procedures, ensure that power is removed from the DC circuit.  
Statement 1003  
Safety Guidelines  
Follow these guidelines to ensure general safety:  
Keep the chassis area clear and dust-free during and after installation.  
Place the removed chassis cover in a safe place.  
Keep tools away from walk areas where you or others could fall over them.  
Do not wear loose clothing that may get caught in the chassis. Fasten your tie or scarf and roll up  
your sleeves.  
Wear safety glasses when working under conditions that may be hazardous to your eyes.  
Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.  
Safety with Electricity  
Warning  
Before working on equipment that is connected to power lines, remove jewelry (including rings,  
necklaces, and watches). Metal objects will heat up when connected to power and ground and can  
cause serious burns or weld the metal object to the terminals. Statement 43  
Follow these guidelines when working on equipment powered by electricity:  
Locate the room’s emergency power-off switch. Then, if an electrical accident occurs, you can  
quickly shut the power off.  
Before working on the system, turn off the power and unplug the power cord.  
Disconnect all power.  
Do not work alone if potentially hazardous conditions exist.  
Look carefully for possible hazards in your work area, such as moist floors, ungrounded power  
extension cables, and missing safety grounds.  
Never assume that power is disconnected from a circuit. Always check.  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Items in the Fan Replacement Kit  
If an electrical accident occurs, proceed as follows:  
Use caution, and do not become a victim yourself.  
Turn off power to the system.  
If possible, send another person to get medical aid. Otherwise, determine the condition of the  
victim and then call for help.  
Preventing Electrostatic Discharge Damage  
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when  
electronic printed circuit cards are improperly handled and can result in complete or intermittent  
failures. Always follow ESD-prevention procedures when removing and replacing cards. Ensure that the  
router chassis is electrically connected to earth ground. Wear an ESD-preventive wrist strap, ensuring  
that it makes good skin contact. Connect the clip to an unpainted surface of the chassis frame to safely  
channel unwanted ESD voltages to ground. To properly guard against ESD damage and shocks, the wrist  
strap and cord must operate effectively. If no wrist strap is available, ground yourself by touching the  
metal part of the chassis.  
Caution  
For safety, periodically check the resistance value of the antistatic strap, which should be between 1 and  
10 megohms (Mohms).  
Items in the Fan Replacement Kit  
The fan replacement kit contains the following items:  
Fan unit (three fans connected together as one unit)  
Additional replacement screws (a few extra screws are provided in case you misplace the original  
screws)  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers document (this  
document)  
Required Tools and Equipment  
Installation might require some tools and equipment that are not provided as standard equipment with  
the router. The following tools and parts are required for a typical router installation:  
Number 2 Phillips screwdriver  
ESD-preventive wrist strap  
Antistatic mat  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Location of the Cisco 2821 and Cisco 2851 Router Fans  
Location of the Cisco 2821 and Cisco 2851 Router Fans  
Figure 1 shows the location of the fan unit in the Cisco 2821 and Cisco 2851 routers. The router contains  
three fans, which are connected together as one unit.  
Figure 1  
Fan Unit Location in the Cisco 2821 and Cisco 2851 Routers  
1
1
Location of the fan unit  
Upgrading the Cisco 2821 and Cisco 2851 Fan Unit  
The fan unit and cabling for the Cisco 2821 and Cisco 2851 routers are contained inside the chassis.  
Note  
The fan unit upgrade procedure will take approximately one hour.  
To upgrade the fan unit, complete these procedures:  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Upgrading the Cisco 2821 and Cisco 2851 Fan Unit  
Removing the Router Cover  
To access the Cisco 2821 or Cisco 2851 fan unit, you must first remove the bezel and then remove the  
router cover. The bezel is the front plastic panel on the chassis, which has the Cisco logo, LEDs, ports,  
and input power connection.  
To remove the bezel and router cover, complete the steps that follow. You will need a number 2 Phillips  
screwdriver.  
If your router uses AC or DC power, observe the following warning:  
Warning  
Warning  
Do not touch the power supply when the power cord is connected. For systems with a power switch,  
line voltages are present within the power supply even when the power switch is off and the power  
cord is connected. For systems without a power switch, line voltages are present within the power  
supply when the power cord is connected. Statement 4  
If your router uses DC power, observe the following warning:  
Before performing any of the following procedures, ensure that power is removed from the DC circuit.  
Statement 1003  
Step 1  
Power down the router and disconnect the power cord from the front of the router.  
Warning  
Before opening the unit, disconnect the telephone-network cables to avoid contact with  
telephone-network voltages. Statement 1041  
Step 2  
Step 3  
Step 4  
Disconnect all network interface cables from the back panel of the router.  
Place the router on a flat surface.  
Remove the bezel from the front of the router. Follow these steps.  
Caution  
Before removing the bezel, make sure that the flash memory card ejector button is flush with the bezel.  
If the button projects from the bezel, removing the bezel can damage it.  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Upgrading the Cisco 2821 and Cisco 2851 Fan Unit  
a. Grasp the bezel at the upward-facing arrow located at the top and center of the front bezel. (See  
Figure 2  
Location of the Arrow on the Bezel  
.
1
1
0
SYS AUX/ SYS  
PWR PWR ACT  
CF  
COMPACT FLASH  
Do Not Remove During Network Operation  
CONSOLE  
AUX  
SYS AUX/ SYS  
PWR PWR ACT  
1
0
CF  
COMPACT FLASH  
Do Not Remove During Network Operation  
100-240V~ 8A  
50/60 Hz  
OPTIONAL RPS INPUT  
12V  
-48V  
18A  
8A  
1
Location of the arrow  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Upgrading the Cisco 2821 and Cisco 2851 Fan Unit  
b. Pull the top of the bezel 1/8 to 1/4 inch (3 to 8 mm) away from the chassis. (See number 1 in  
Figure 3  
Removing the Bezel  
.
Plastic bezel  
1
2
1
Pull top of bezel away from chassis  
2
Slide bezel to release it from chassis  
c. While holding the bezel away from the chassis, slide it toward the left side (input power side) until  
it comes off the chassis, as shown in Figure 3. (See number 2 in Figure 3.)  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Upgrading the Cisco 2821 and Cisco 2851 Fan Unit  
Step 5  
Remove the router cover. Follow these steps:  
a. Use a number 2 Phillips screwdriver to remove the three screws at the back of the top cover. Set the  
screws aside in a safe place.  
b. Lift the cover up at a 45-degree angle, as shown in Figure 4.  
Figure 4  
Removing the Cover from a Cisco 2821 or Cisco 2851 Router  
2
1
1
Lift cover  
2
Slide cover to free the tabs  
c. Slide the cover to the side (toward the side with the fans) until the tabs are free from the slots, as  
shown in Figure 4.  
d. Lift the cover away from the router chassis, and set the cover aside.  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Upgrading the Cisco 2821 and Cisco 2851 Fan Unit  
Removing the Fan Unit  
After you remove the router cover, follow these steps to remove the fan unit.  
Note  
Before you begin, read the safety warnings as described in the “Safety Warnings and Guidelines” section  
Step 1  
Locate the three fan connectors on the motherboard and remove them by lifting the connector away from  
the receptacle, as shown in Figure 5.  
Figure 5  
Lifting the Connector from the Receptacle  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Upgrading the Cisco 2821 and Cisco 2851 Fan Unit  
Step 2  
Remove the three screws that hold the fan unit to the side of the chassis. (See number 1 in Figure 6.)  
Figure 6  
Removing Fan Mounting Screws from the Chassis  
1
2
1
Fan mounting screws on the side of the  
chassis  
2
Fan mounting screw on the front of the chassis  
Step 3  
Step 4  
Remove the one screw that holds the fan unit to the front of the chassis. (See number 2 in Figure 6.)  
Lift the fan unit out of the chassis.  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Upgrading the Cisco 2821 and Cisco 2851 Fan Unit  
Installing the Fan Unit  
Follow these steps to install the fan unit.  
Note  
Before you begin, read the safety warnings as described in the “Safety Warnings and Guidelines” section  
Step 1  
Step 2  
Step 3  
Step 4  
Lower the fan unit down and onto the chassis floor.  
Attach fan 1 to the J9 connector on the motherboard. (See number 1 and 2 in Figure 7.)  
Attach fan 2 to the J8 connector on the motherboard. (See number 3 and 4 in Figure 7.)  
Attach fan 3 to the J7 connector on the motherboard. (See number 5 and 6 in Figure 7.)  
Caution  
The connectors are polarized/keyed to allow easy insertion in one orientation only. Orient the fan  
connectors correctly before you insert them. Incorrect orientation can damage the connector pins.  
Figure 7  
Attaching Fan Cable to the J Connectors  
1
2
4
3
6
5
1
3
5
Fan 1  
2
4
6
Fan 1 to J9 connector  
Fan 2 to J8 connector  
Fan 3 to J7 connector  
Fan 2  
Fan 3  
Step 5  
Step 6  
Reinstall the one screw on the front of the chassis. (See number 2 in Figure 6 on page 17.)  
Reinstall the three screws on the side of the chassis. (See number 1 in Figure 6 on page 17.)  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Upgrading the Cisco 2821 and Cisco 2851 Fan Unit  
Replacing the Router Cover  
Note  
Before you begin, read the safety warnings as described in the “Safety Warnings and Guidelines” section  
To replace the chassis cover on a Cisco 2821 or Cisco 2851 router, follow these steps. You need a number  
2 Phillips screwdriver.  
Step 1  
Step 2  
Place the chassis on a flat surface.  
Hold the cover at a 45-degree angle, and insert the tabs into the slots along the front (bezel) edge of the  
chassis, as shown in Figure 8.  
Figure 8  
Installing the Cover on the Cisco 2821 or Cisco 2851 Routers  
1
2
1
Insert tabs and center the cover  
2
Close the cover  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Obtaining Documentation, Obtaining Support, and Security Guidelines  
Step 3  
Step 4  
Center the cover over the chassis and lower it onto the chassis, as shown in Figure 8.  
Reinstall the three cover screws.  
Caution  
Step 5  
When replacing the cover, do not pinch the wires.  
Replace the bezel by sliding it into the front of the chassis. Make sure the upward-facing arrow on the  
bezel is at the top and center of the chassis, as shown in Figure 2 on page 13.  
Step 6  
Step 7  
Reconnect power and network interface cables.  
Power up the router, and verify that the alarms and warnings disappear.  
Obtaining Documentation, Obtaining Support, and Security  
Guidelines  
For information on obtaining documentation, obtaining support, providing documentation feedback,  
security guidelines, and also recommended aliases and general Cisco documents, see the monthly  
What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical  
documentation, at:  
CCDE, CCENT, Cisco Eos, Cisco StadiumVision, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way We  
Work, Live, Play, and Learn is a service mark; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE,  
CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems  
Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Event  
Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQ Expertise, the iQ logo, iQ Net  
Readiness Scorecard, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace, MGX, Networkers, Networking  
Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The  
Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its  
affiliates in the United States and certain other countries.  
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply  
a partnership relationship between Cisco and any other company. (0803R)  
© 2008 Cisco Systems, Inc. All rights reserved.  
Installing and Upgrading Fans in the Cisco 2821 and Cisco 2851 Series Routers  
78-18643-02  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

Cobra Electronics Marine GPS System MC 600CI User Manual
Cooper Lighting Indoor Furnishings 1268 User Manual
Craftsman Lawn Mower 91737742 User Manual
Cuisinart Coffeemaker PRC 12 Series User Manual
Dell Server 3YPMN User Manual
Edelbrock Water Pump 8805 User Manual
Electro Voice Microphone PL50 N D User Manual
Electro Voice Portable Speaker EVX 180A User Manual
Gitzo Camcorder Accessories GT3531 User Manual
Global Machinery Company Portable Generator LSSLV User Manual