MODEL L-1X & L-1X16
Installation & Operations
Rev 1.14
C M A D I S H M A C H I N E S
1 2 7 0 0 K N O T T A V E N U E
GARDEN GROVE, CALIFORNIA 92841
8 0 0 - 8 5 4 - 6 4 1 7
FAX 714-895-2141
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Specifications
METRIC
EQUIVALENT
1.1.
L-1X & L-1X16
WATER CONSUMPTION
PER RACK
1.7 GAL.
6.44 L
PER HOUR
40.8 GAL.
154.4 L
OPERATING CYCLE
WASH TIME-SEC
57
48
57
48
RINSE TIME-SEC
DWELL TIME-SEC
TOTAL CYCLE
15
15
2 MIN.
2 MIN.
OPERATING CAPACITY
RACKS PER HOUR
WASH TANK CAPACITY
PUMP CAPACITY
24
1.7 GAL.
35 GPM
140°F
½”
24
6.44 L
132.5 LPM
60°C
WATER REQUIREMENTS
WATER INLET
—
DRAIN CONNECTION
CYCLE TEMPERATURES
WASH-°F (Min)
1”
—
140
60°C
FRAME DIMENSIONS
DEPTH
23 ½”
24”
59.69 cm
60.96 cm
76.2 cm
WIDTH
L-1X HEIGHT
30”
L-1X16 HEIGHT
33 ¾”
12 ¼”
16”
85.73 cm
31.11 cm
40.64 cm
L-1X MAX CLEARANCE FOR DISHES
L-1X16 MAX CLEARANCE FOR DISHES
ELECTRICAL*
115 VAC
15.8 AMPS
0.8 kW
SUSTAINER HEATER
(Not Booster Heater)
WASH PUMP MOTOR
13.4 AMPS
*MUST CONNECT TO DEDICATED 20 AMP SUPPLY CIRCUIT.
COMPLIANCE WITH LOCAL ELECTRICAL CODES MUST BE FOLLOWED.
SHIPPING WEIGHT
L-1X (Approximate)
190#
195#
86.2 kg
88.5 kg
L-1X16 (Approximate)
MODEL L-1X & L-1X16 INSTALLATION & OPERATION MANUAL Rev. 1.14
Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2.
L-1X and L-1X16 Operational Cycle
The L-1X and L-1X16 Operational Cycle has a total cycle time of 2 minutes (120
seconds). The Timing Diagram and the steps listed below detail the individual functions
that are executed during each Operational Cycle.
Seconds:
0
10
20
30
40
50
60
70
80
90
100
110
120
Instant
Start Relay
Cam 1
Cam 2
Cam 3
Cam 4
Start/Stop
Detergent
WASH
RINSE
DRAIN
Drain/Rack
Counter
Flush/Fill
Sanitizer
Cam 5
Cam 6
Rinse
Pump Motor
Cam 7
Cam 8
Heater*
*Heater is optional
1. With the machine powered up, toggling the START switch begins a cycle.
a) Toggling the START switch energizes both the cam timer motor and the instant
start relay. The instant start relay latches ON the power to the cam timer motor so
that the START switch can be released a moment after it has been toggled without
the cam timer motor losing power.
b) After about 2 seconds, Cam 1—the Start cam—latches ON the power to the cam
timer motor and drops out the instant start relay. The cam timer motor continues
to run for a total of 2 minutes, at which time it switches OFF—resetting the cam
timer—and waits for the next start command.
2. Cam switch 7 controls the pump motor. The pump motor comes ON at the beginning
of the operational cycle and continues to run until the end of the drain function
(controlled by cam switch 3), at which time it turns off for about eight seconds
MODEL L-1X & L-1X16 INSTALLATION & OPERATION MANUAL Rev. 1.14
Page
3
Download from Www.Somanuals.com. All Manuals Search And Download.
allowing time for the machine to refill enough to avoid running the pump dry before
the pump motor restarts and runs to the completion of the operational cycle.
The pump motor runs the pump for the 57-second wash cycle, then pumps the water
out through the drain, turns off for about 8 seconds (allowing the machine to refill with
clean rinse water) and then runs the pump for the 48-second rinse cycle.
3. Cam switch 3 controls the drain function. At the end of the 57-second wash cycle,
cam switch 3 energizes the drain valve solenoid allowing the pump motor to drain the
wash water out of the machine. Cam switch 3 also increments the rack counter by one
each cycle.
4. Cam switch 4 controls the water valve solenoid on the water supply to flush and fill
the machine. At the end of the wash cycle the drain valve is opened, the pump motor
continues to run (to pump the wash water out through the drain), and the Flush
function begins. At first, flushing the machine because the drain valve is still open,
then—with the drain valve closed and the pump motor stopped— the machine begins
to fill for the rinse cycle. Once the machine has refilled sufficiently, the pump motor
restarts carrying out the rinse portion of the cycle as the filling of the wash tank
completes.
5. Cam switch 2 controls the detergent pump and turns ON about 5 seconds after the
operational cycle is started and runs for a few seconds to provide sufficient detergent
for the wash cycle. This cam can be adjusted as necessary for proper detergent
dosage.
6. Cam switches 5 and 6 control the sanitizer and rinse pumps respectively. They turn
ON at the beginning of the rinse cycle and run for a few seconds to provide sufficient
7. Cam switch 8 operates the optional sustainer heater. This cam assures that the
sustainer heater only turns on when the dishmachine is not in a cycle. This prevents
the machine from drawing too much electrical current at any one time.
MODEL L-1X & L-1X16 INSTALLATION & OPERATION MANUAL Rev. 1.14
Page
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
2. Getting Started
All sections of the manual address both the L-1X and the L-1X16. Separate information on each
machine is only provided where differences exist between the two models.
2.1.
Introduction to the L-1X and L-1X16
The L-1X and L-1X16 Dishmachines are unique in their field; they have all the features of a
standard commercial size machine packed into an under-counter, standalone dishmachine.
Operation of the L-1X and L-1X16 are extremely easy. After initially filling the machine (see
section 3.1.3 Filling the Machine), toggling the Fill/Start switch to the “START” position begins the
Operational Cycle, which runs automatically.
To reduce service time, all electrical components are mounted in a sliding drawer for easy access.
This “Works-In-A-Drawer” can be removed by unplugging a single connector for easy
serviceability.
The only external connections necessary are the power source, water supply and drainpipe.
There are also accessories that can be chosen when desired such as the optional sustainer heater
and 6” legs. The optional sustainer heater with thermostat is extremely practical for maintaining
wash tank temperature between cycles. The 800 watt heater will hold the wash tank temperature
between 130°F and 140°F while the machine is not being run. See section Error! Reference
source not found. Error! Reference source not found. for the parts list and accessories available
for the machine.
The supply water to the L-1X and L-1X16 must be a minimum of 140°F. The pipe supplying the
water must be ½” minimum. The plumbing connection is located at the back of the machine. The
drain is a 1" barbed fitting located at the back of the machine for easy attachment of your drain
This manual is structured to provide a complete reference guide to the L-1X and L-1X16. It is
presented in a manner that all users will be able to comprehend and use as an effective tool in
supporting the installation, operation and maintenance of the dishmachine. The first section
provides the specifications and details of the operational cycle. The next section explains how the
machine is packaged and what to look for when receiving the machine. After unpacking the
machine, this manual explains how to install and set up the machine for use. Requirements are
given for plumbing, wiring, and space considerations. These attributes of the machine are always
taken into consideration by our well-trained sales representatives prior to the order being placed.
In the manual, guidance is also given for operation to ensure that the machine will be able to run
optimally.
We make this portion of the manual easy to understand so that all levels of operators may be able
to read and comprehend the operation of the machine. The function of the machine itself is mostly
diagnostic considerations for the machine if problems occur.
The Maintenance section of the manual is for qualified personnel and provides trouble shooting
procedures and specific maintenance instructions.
The final section of the manual is the Parts Manual. This section has the parts lists and wiring
diagram for the machine.
CMA warranties the workmanship of the machine.
At CMA we are committed to providing the best machines and customer service in the food and
beverage industry and your feedback is welcome.
MODEL L-1X & L-1X16 INSTALLATION & OPERATION MANUAL Rev. 1.14
Page
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
2.2.
Receiving and Installation
The dishwasher is shipped from the factory in a corrugated box on a wooden pallet. The
installation guidelines give a systematic procedure for setting up the machine.
1. Start by removing the box and packaging material. Check for the following component parts:
A. Drain Screen:
The Wash Tank Scrap Screen is shipped inside the wash cavity of the machine. This
screen must be in place during operation. It has been designed to perform two basic
functions:
•
•
Strain water that is circulating through the spray arms and pump assembly.
A basket to catch heavy solids or broken glass that may plug the impeller.
B. Spray Arms
The end caps on the spray arms have been taped to protect them in shipping. Remove
the tape from the spray arm end caps.
C. Tube Stiffeners:
The tube stiffeners must be used to prevent the feed tubes from curling up inside the
chemical pail allowing the tip to rise out of the chemical. Remove the tie-wraps securing
the tube stiffeners to the dishmachine to free them up for use. Be careful not to remove
any of the tie-wraps securing the tube bundle.
2. Set the machine in place and, using the leg adjusters, level from side-to-side and front-to-
back.
2.2.1. Electrical*
A 20-amp, 115 volt, 60 Hz dedicated circuit must be used to supply electrical power to the L-1X or
there is sufficient length of flexible conduit or power cord to permit the machine to be moved for
cleaning.
2.2.2. Plumbing*
The machine is equipped with a gate valve with a ½” female NPT connection located at the lower
left-hand corner (facing the back) of the machine. A 140°F water line should be plumbed to this
point. The water line used must be of sufficient length and flexibility to permit the machine to be
moved for cleaning.
A 1” male NPT fitting is provided for the drain connection on the discharge port of the diverter
valve (lower, right-hand corner of machine). This fitting may be removed and user provided
hardware may be used if necessary to facilitate compliance with local plumbing codes. Code
requires that the drain discharge provides an air gap no less than 1” or two pipe diameters,
whichever is greater, above the flood level rim of an approved floor drain.
2.2.3. Post Instructions
Mount the wall chart provided in a conspicuous place and instruct the operators on proper cleaning
and operation of the L-1X and L-1X16. The instruction chart is also provided as an appendix to
this manual (see appendix).
* Electrical and plumbing connections must be made by a qualified person who will comply with all
available Federal, State, and Local Health, Electrical, Plumbing and Safety codes
MODEL L-1X & L-1X16 Installation & Operations Manual Rev. 1.14
Page6
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
2.2.4. Installers Checklist
ꢀ Dishmachine checked for concealed damage
ꢀ Hot water supply is 140° F (60 C)
ꢀ Incoming water supply line is ½” minimum
ꢀ Supply circuit breaker for machine is properly sized (20 amp)
ꢀ Service voltage and phase type are correct to machine data plate
ꢀ Drain hose is installed with adequate air gap
ꢀ Dishmachine is properly grounded
ꢀ Dishmachine is properly leveled
ꢀ Machine circuit breaker is labeled “DISHWASHER”
ꢀ Machine has been connected with correctly sized wire (12 gauge
minimum)
MODEL L-1X & L-1X16 Installation & Operations Manual Rev. 1.14
Page7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
3. Operation
3.1.
Initial Setup
3.1.1. Check…
ꢀDrain screen is in place
ꢀSpay arms and end plugs are secure
3.1.2. Chemicals
Assure there is a sufficient supply of chemicals before beginning a shift.
3.1.3. Filling the Machine
With the power ON, toggle and hold the Fill/Start switch in the “FILL” position
•
•
until the water level in the wash tank is about 1” deep, or just below the
bottom wash arm.
3.2.
General
Caution: Do not operate the dishmachine without the drain screen in place. Debris
getting into the pump impeller can damage the pump.
1. Load a rack of properly pre-scrapped dished into the machine and close the door.
2. With the machine filled to the proper level, toggle the Fill/Start switch to the “START”
position – the machine will automatically begin its cycle. The green running light will
illuminate while an operational cycle is in process.
3. At the end of the shift, drain the machine by holding the Drain toggle switch in the
“DRAIN” position until the machine is completely drained. To avoid running the pump
dry, do not hold the Drain toggle switch in the “DRAIN” position any longer than
necessary.
4. Remove and clean the drain screen. Remove and clean the spray arms. (See wall
chart instructions or instructions provided in Appendix A: Operator & Cleaning
Instructions).
5. Replace the drain screen and spray arms.
3.2.1. Pre-Scrapping
It is essential that the operator thoroughly understand the importance of pre-scrapping the
dishes before loading them. The L-1X and L-1X16 are equipped with a removable drain
screen. The drain screen can be easily removed for cleaning between Operational Cycles
of the dishmachine. Properly pre-scrapping the dishes should permit the dishmachine to
operate for an entire shift before needing to remove and clean the drain screen.
3.2.2. Proper Chemical Dosage
The amount of chemical delivered, whether it is detergent, sanitizer or rinse aid, is
determined by its respective cam on the cam timer.
•
•
•
Cam number 2 runs the detergent pump
Cam number 5 runs the sanitizer pump
Cam number 6 runs the rinse aid pump
MODEL L-1X & L-1X16 INSTALLATION & OPERATION MANUAL Rev. 1.14
Page
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
These cams were set at the factory but can be adjusted after final installation to maximize
3.2.3. Proper Filling
The amount the machine is automatically filled each cycle is determined by the number 4
cam. When the number 4 cam switch actuator rides down into the cam groove, the
solenoid valve on the fill line is energized causing the machine to fill. Since the cam only
controls the duration of the fill, varying water pressure can vary the amount the machine
fills. If the water pressure at the facility where the machine is installed is enough higher or
lower than the water pressure was at the factory, the number 4 cam may need to be
below the lower wash arm. If the water pressure at the facility varies throughout the day, a
pressure regulator may have to be installed on the water supply line to the machine to
maintain constant pressure.
Note: If the optional sustainer heater is installed, the wash tank must be properly filled,
and the machine properly leveled, or the float switch, which prevents the heater from
turning on if the level is too low, will not permit the heater to turn on.
3.2.4. Water Pump
The water pump takes in water from the drain sump and pumps it to the spray nozzles at a
rate of 68 gallons per minute and a pressure at the nozzles of approximately 7 to 10 PSI.
After being released through the spray arms and washing or rinsing the dishes, the water
runs down the pan to the sump, through the drain screen, and back to the pump.
The pump is driven by a 115 volt, 1 HP motor operating at 3450 RPM. The impeller is
mounted with a right-hand thread onto a 5/8” stainless steel shaft, which is coupled to the
motor armature shaft. See section Error! Reference source not found. Error! Reference
source not found. for a detailed drawing.
3.2.5. Pump Cavitation
By listening to the normal pumping sound of the motor it can be determined if there is
insufficient water in the machine, as you will hear a hesitation in the normal pumping
rhythm, which is created by the air getting into the pump. Cam 4 can be adjusted to
increase the amount of water that is automatically fed into the machine during a cycle (see
MODEL L-1X & L-1X16 Installation & Operations Manual Rev. 1.14
Page9
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
4. Maintenance
The maintenance procedures detailed in this section are to be performed by qualified personnel.
4.1.
Timer assembly
The standard timer assembly consists of a ½ RPM (2 minutes per revolution) motor turning a common
shaft, which, in turn, rotates eight cams. As the cams rotate, they control various functions and the
sequence of the operational cycle.
The individual function of each of the 8 cams is identified by a label on the timer assembly. Cams 1
through 8 are positioned from left to right beginning with the “START” cam (cam 1).
*
MOTOR
PAUSE
START
DET.
DRAIN
FLUSH
SANI.
RINSE
HEATER
Timer Assembly Label
*The “HEATER” label is not present if the optional sustainer heater is not installed on the machine.
Except for cams 1, and 3, all other cams can be user adjusted. The cam positions are all set at the
factory and only the cams controlling the chemical pumps (cams 2, 5 & 6) should ever need adjusting.
Each micro switch on the timer assembly is turned on and off by the cam its actuator rides on. For all of
the cams, except cams 1, 7 and 8, its corresponding switch is ON when its actuator is down in the cam
groove. (Cams 1, 7 and 8 are reverse acting and are turned ON when the micro switch actuator is up
out of the groove.) Opening the groove of any cam other than cams 1, 7 or 8 will increase the amount of
time that the micro switch is held ON. The cams are slip-fit and a cam adjustment wrench is provided (a
small screw driver or the edge of a table knife can also work to adjust the cams).
4.1.1. Cam Adjustment
The two sides of each cam connect to the shaft with a slip-fit so all cam adjustments are made
by rotating one side of the cam on the shaft to either increase or decrease the size of the cam
groove.
1. Turn off the circuit breaker providing power to the machine before pulling the control drawer
out to access the timer assembly.
Caution: One of the terminals on the main power switch remains “hot” even when the
machine’s main power switch is turned off—so turn the power off at the circuit breaker.
2. Remove the two 8–32 x ½” Screws securing the control drawer and slide it out to its fully
extended position.
3. Using the timer assembly label, determine which cam is to be adjusted. Double check by
counting over from cam 1 to the cam to be adjusted.
4. Determine which edge of the cam groove to be adjusted is the leading edge (contacts the
limit switch actuator first when the shaft is rotating) and which edge of the groove is the
trailing edge. The leading edge of the cam groove determines when in the cycle the control
action begins and should not be changed.
5. Adjust the trailing edge of the cam groove by rotating the appropriate side of the cam in the
proper direction to either increase or decrease the cam’s groove; resulting in increasing or
decreasing the total time that switch will be held ON.
MODEL L-1X & L-1X16 PARTS MANUAL Rev. 1.14
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
4.2.
Quick service guide
MODELS: L-1X, L-1X16 UNDER COUNTER
TECHNICAL ISSUE
CAUSE
SOLUTION
Delimer switch in delime position
Faulty delimer switch
Flip to NORMAL position
Wash Pump motor will not shut off
Replace switch, P/N 00475.30
Replace switch, P/N 03406.62
Replace contactor, P/N 00404.82
Replace switch, P/N 00411.00
Replace switch, P/N 03470.01
Faulty manual drain switch
Faulty contactor
Continues cycles
Faulty #1 micro switch (start/stop)
Faulty start/fill switch
Faulty #1 micro switch
Replace switch, P/N 00411.00
Add water to tank to activate float switch, adjust
water cam on timer
Low water level inside machine
Faulty float switch
Sustainer heater not working
Replace switch, P/N 13463.10
Level machine
Machine not level
Faulty ice cube relay
Replace relay, P/N 00631.00
Replace switch, P/N 00411.00
Replace drain valve, P/N 04103.00
Replace switch, P/N 00411.00
Machine does not drain
Does not hold water
Faulty #3 micro switch (drain)
Faulty drain valve
Faulty #3 micro switch (drain)
Clogged or defective drain valve
Clean and/ or replace drain valve, P/N 04103.00
Clean and replace valve diaphragm, P/N
00707.00
Tank overflows overnight
Debris in water Solenoid Valve
Dirty or defective vacuum breaker kit
assy
Clean or replace internal parts, P/N 03623.00
Water leaks out of Vacuum Breaker
Faulty check valve
Replace check valve, P/N 00715.00
Male/ female plug on the back of control Secure plug
drawer is loose
Wash Pump motor not running
Timer does not rotate
Faulty door reed switch
Faulty 7th micro switch
Faulty motor contactor
Faulty Start/Fill Switch
Faulty #1 micro switch
Faulty timer motor
Replace reed switch, P/N 00557.55
Replace switch, P/N 00411.00
Replace contactor, P/N 00404.82
Replace switch, P/N 03470.01
Replace switch, P/N 00411.00
Replace motor assembly, P/N 00501.00
Replace switch, P/N 00411.00
Faulty #4 Micro switch
Debris inside water solenoid valve or
Faulty valve
Clean and replace valve diaphragm, P/N
00707.00
Machine does not fill
Faulty water solenoid coil
Delimer switch in wrong position
Faulty 5th micro switch
Replace solenoid coil, P/N 00738.10
Switch to NORMAL position
Sanitizer pump does not run
Replace switch, P/N 00411.00
Replace motor, P/N 00416.00
Faulty sanitizer pump motor
MODEL L-1X & L-1X16 PARTS MANUAL Rev. 1.14
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
4.3.
Troubleshooting
PROBLEM
LIKELY CAUSE
SOLUTION
Machine inoperative
Power off at circuit breaker
Defective power switch
Reset circuit breaker
Replace power switch
P/N: 00433.10
Defective timer assembly motor
Replace timer assembly motor
P/N: 00501.00
Pump Motor inoperative
Door is open
Close door
Control drawer is pulled out
Defective reed (door) switch
Secure control drawer
Replace reed (door) switch
P/N: 00557.55
Defective timer assembly
(Cam 7)
Replace timer assembly*
P/N: 00408.80
Defective pump motor contactor
Replace contactor
P/N: 00404.82
Defective pump motor
Replace pump motor
P/N: 00201.00
Pump Motor runs with door Defective reed (door) switch
open
Replace reed (door) switch
P/N: 00557.55
Defective pump motor contactor
Replace contactor
P/N: 00404.82
Delime switch is on
Turn off delime switch
Turn off delime switch
Motor runs continuously
Delime switch is on
Optional Sustainer Heater
(no heat)
Defective thermostat on heater
Replace heater
P/N: 04109.10
Defective heater relay
Replace heater relay
P/N: 00631.00
Defective timer assembly
(Cam 8)
Replace timer assembly *
P/N: 00408.80
Defective heater
Replace heater
P/N: 04109.10
Defective float switch
Float switch not actuated
Replace float switch
P/N: 13463.00
Fill wash tank completely
Level machine
Optional Sustainer Heater
(never turns off)
Defective thermostat on heater
Replace heater
P/N: 04109.10
Defective timer assembly
(Cam 8)
Replace timer assembly *
P/N: 00408.80
Defective heater relay
Replace heater relay
P/N: 00631.00
*The timer assembly motor (P/N: 00501.00) or micro switches (P/N: 00411.00) can be replaced
independently if that is the only component that has failed.
MODEL L-1X & L-1X16 PARTS MANUAL Rev. 1.14
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
PROBLEM
LIKELY CAUSE
SOLUTION
Low heat during operation
Low incoming water temperature
(below 140° F)
Turn up supply water heater
Insulate supply water pipe
Adjust thermostat
Thermostat out of adjustment
(Optional) sustainer heater not
installed
Install (optional) sustainer
heater
P/N: 04109.10
Defective sustainer heater
Replace heater
P/N: 04109.10
Low spray arm water flow
With power on, activating
Limed up spray arm nozzles
Defective fill/start switch (cycle
De-lime spray arm nozzles
Replace fill/start switch
start switch does not begin light will not light either)
P/N: 03470.01
cycle
Defective timer assembly
Replace timer assembly*
(Cam 1)
P/N: 00408.80
Start switch requires more
Defective (Instant Start) ice cube
Replace ice cube relay
than 1-second activation to relay
run cycle
P/N: 00631.00
Activating fill switch does
not fill machine
Defective fill/start switch
Replace fill/start switch
P/N: 03470.01
Defective water solenoid valve
Defective water solenoid valve
Defective fill/start switch
Replace water solenoid valve
P/N: 03603.10
Fill water won’t shut off
Replace water solenoid valve
P/N: 03603.10
Replace fill/start switch
P/N: 03470.01
Defective timer assembly
(Cam 4)
Replace timer assembly*
P/N: 00408.80
Activating drain switch
does not drain machine
Drain hose is kinked
Defective drain switch
Un-kink drain hose
Replace drain switch
P/N: 03406.64
Defective drain valve motor
(Pump will still run)
Replace drain valve motor
P/N: 04103.21
Detergent pump does not
run
Defective detergent pump motor
Replace pump motor
P/N: 00416.00
Defective timer assembly
(Cam 2)
Replace timer assembly*
P/N: 00408.80
Sani pump does not run
Defective sani pump motor
Replace pump motor
P/N: 00416.00
Defective timer assembly
(Cam 5)
Replace timer assembly*
P/N: 00408.80
*The timer assembly motor (P/N: 00501.00) or micro switches (P/N: 00411.00) can be replaced
independently if that is the only component that has failed.
MODEL L-1X & L-1X16 PARTS MANUAL Rev. 1.14
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
PROBLEM
LIKELY CAUSE
SOLUTION
Rinse pump does not run
Defective rinse pump motor
Replace pump motor
P/N: 00416.00
Defective timer assembly
(Cam 6)
Replace timer assembly*
P/N: 00408.80
Activating detergent primer Defective sani/detergent primer
Replace primer switch
switch does not run pump
switch
P/N: 03470.00
Defective detergent pump motor
Replace pump motor
P/N: 00416.00
Activating sani primer
switch does not run pump
Defective sani/detergent primer
switch
Replace primer switch
P/N: 03470.00
Defective sani pump motor
Defective rinse primer switch
Defective rinse pump motor
Defective counter
Replace pump motor
P/N: 00416.00
Activating rinse primer
switch does not run pump
Replace primer switch
P/N: 03470.00
Replace pump motor
P/N: 00416.00
Counter does not
increment
Replace counter
P/N: 03408.50
Defective timer assembly
(Cam 3)
Replace timer assembly*
P/N: 00408.80
Running light does not
light while cycle runs
Defective cycle light
Replace running light (green)
P/N: 00476.00
Power light does not light
but machine runs
Defective power light
Replace power light (red)
P/N: 00406.00
Wash tank temperature
gauge displays wrong
temperature
Defective temperature gauge
Replace temperature gauge
P/N: 03202.00
Delime switch does not
activate pump motor
Defective delime switch
Defective pump motor
Replace delime switch
P/N: 00475.30
Replace pump motor
P/N: 00201.00
*The timer assembly motor (P/N: 00501.00) or micro switches (P/N: 00411.00) can be replaced
independently if that is the only component that has failed.
MODEL L-1X & L-1X16 PARTS MANUAL Rev. 1.14
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Addendum
5.Addendum for Machines Installed in the City of Chicago
“All food dispensing establishments using chlorine or other approved chemical sanitizers shall, at all
times, maintain an adequate testing device.”
“Dishes and other eating and drinking utensils to be washed in a dishwashing machine shall be
properly scraped and pre-rinsed and shall be stacked in racks or trays so as to avoid overcrowding,
and so as to permit the wash and rinse waters to reach all surfaces of each utensil.”
“In machine washing, multi-use eating and drinking utensils shall be washed in water containing a
suitable detergent at a temperature of 120° F to 140° F or other method approved by the Department
of Health.”
“The water in the wash tank shall be changed during operation as often as is necessary to keep it
reasonably clean. An effective concentration of detergent in the wash water shall be maintained at
all times.”
“Bactericidal treatment shall consist of exposure of all surfaces of dishes and utensils being washed
to a rinse of clean water, at a temperature of not less than 180° F or other method approved by the
Department of Health.”
“All dishwashing machines shall maintain a flow pressure not less than 15 or more than 25
pounds per square inch on the fresh water line at the machine and not less than 10 pounds per
square inch at the rinse nozzles. A suitable gauge cock shall be provided immediately upstream
from the final rinse sprays to permit checking the flow of the final rinse water. An easily readable
thermometer accurate to a +2° F. shall be provided on both the wash and rinse water lines of the
dishwashing machine which will indicate the temperature of the water solution there in.”
“Dishwashing machines shall be thoroughly cleaned at least once each day. The pumps and the
wash and rinse sprays or jets shall be so designed that a forceful stream of water will reach all
surfaces of the utensils when they are properly racked. These parts shall be thoroughly cleaned at
least once each day. The pumps and the wash and rinse sprays or jets shall be designed that a
forceful stream of water will reach all surfaces of the utensils when they are properly racked. These
pars shall be readily accessible for inspection and cleaning.
“After bactericidal treatment, utensils and containers shall be stored at a sufficient height above the
floor in a clean, dry place, protected from flies, splash, dust, overhead leakage and condensation,
and other contamination. Containers and utensils shall be inverted, covered, or otherwise protected
from contamination until used for serving.”
Drain racks, trays and shelves shall be made of non-corrodible material and shall be kept clean. In
handling containers and utensils the surfaces thereof which come in contact with food or drink shall
not be touched by the hands, except during the process of washing. Tables for clean and dirty
dishes and food shall be so arranged that the dirty dishes will be as far removed from the food and
clean dishes as may be possible.
All single service articles and utensils shall be purchased in sanitary cartons and stored in a clean,
dry place until used, and after removal from the cartons, these articles shall be handled in such a
manner as to prevent contamination.
Please note the following procedures must be followed for City of Chicago Approval:
1. All low energy models must have low level sani-alarms, both visual and audio.
2. All models must have a City of Chicago approval data label affixed to the machine.
3. Chlorine sanitizer must be a minimum of 100 PPM.
MODEL L-1X & L-1X16 PARTS MANUAL Rev. 1.14
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
|
