®
A Division of Cisco Systems, Inc.
Cable Modem
with USB and
Ethernet Connections
User Guide
WIRED
Model No.
BEFCMU10
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Table of Contents
Chapter 1: Introduction
1
1
Welcome
What’s in this Guide?
1
Chapter 2: Getting to Know the Cable Modem
Back Panel Ports
3
3
4
Front Panel LEDs
Chapter 3: Connecting the Cable Modem
Overview
Connection Using the Ethernet Port
Connection Using the USB Port
Chapter 4: Installing the USB Driver for Windows XP
Overview
5
5
5
6
7
7
Instructions for Installing the Driver
Chapter 5: Installing the USB Driver for Windows 2000
Overview
Instructions for Installing the Driver
Chapter 6: Installing the USB Driver for Windows Millennium
Overview
Instructions for Installing the Driver
Chapter 7: Installing the Driver for Windows 98
Overview
Instructions for Installing the Driver
Appendix A: Troubleshooting
Common Problems and Solutions
Appendix B: Windows Help
7
8
8
8
10
10
10
11
11
11
13
13
15
Appendix C: Glossary
Appendix D: Specifications
Appendix E: Warranty Information
Appendix F: Regulatory Information
Appendix G: Contact Information
16
23
24
25
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
List of Figures
Figure 2-1: Back Panel
3
4
Figure 2-2: Front Panel
Figure 3-1: Connect the Coaxial Cable
Figure 3-2: Connect the Ethernet Network Cable
Figure 3-3: Connect the Power Cable
Figure 3-4: Connect the Coaxial Cable
Figure 3-5: Connect the USB Cable
Figure 3-6: Connect the Power Cable
Figure 4-1: Welcome
5
5
5
6
6
6
7
Figure 4-2: Please wait...
7
Figure 5-1: Welcome
8
Figure 5-2: Install Hardware Device Drivers
Figure 5-3: Locate Driver Files
8
8
Figure 5-4: Driver Files Search Results
Figure 5-5: Driver Installation Complete
Figure 6-1: Add New Hardware Wizard
Figure 6-2: Driver Installation Complete
Figure 7-1: Add New Hardware Wizard
Figure 7-2: Search for Driver
Figure 7-3: Select CD-ROM Drive
Figure 7-4: Select Updated Driver
Figure 7-5: Location of Driver
9
9
10
10
11
11
11
12
12
12
Figure 7-6: Driver Installation Complete
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Chapter 1: Introduction
Welcome
Thank you for choosing the Linksys Cable Modem. Experience the savings of owning your own cable modem!
The Linksys Cable Modem is the easiest and most affordable way to get a blazing fast connection to the Internet
-- far faster than a dial-up, and without tying up your phone line. The "always on" connection eliminates dial-up
wait time and busy signals. Web surfing and your e-mail are instantly available, anytime. And with the extra
speed, online gaming is a whole new experience, and download time on big music, video, and other files goes
from hours to minutes.
Installation is quick and simple. Connect it directly to any PC with an available USB or Ethernet port, and you’re
ready to surf the Internet. Or connect it to a Linksys router and share that high-speed Internet access with
everyone on your home network.
The Linksys Cable Modem is fully compliant with all industry standards—DOCSIS 1.0, 1.1, and 2.0—so you know
it’ll work with any cable Internet service provider.
With the Linksys Cable Modem, you'll avoid monthly rent charges, and make the most of your high-speed cable
Internet connection.
What’s in this Guide?
This user guide covers the steps for installing the Cable Modem and installing its USB driver if you are using its
USB connection.
•
•
•
•
Chapter 1: Introduction
This chapter describes the Cable Modem’s applications and this User Guide.
Chapter 2: Getting to Know the Cable Modem
This chapter describes the physical features of the Cable Modem.
Chapter 3: Connecting the Cable Modem
This chapter instructs you on how to connect the Cable Modem using its Ethernet or USB port.
Chapter 4: Installing the USB Driver for Windows XP
This chapter explains how to install the Windows XP driver required for a USB connection to the Cable
Modem.
Chapter 1: Introduction
Welcome
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
•
•
•
Chapter 5: Installing the USB Driver for Windows 2000
This chapter explains how to install the Windows 2000 driver required for a USB connection to the Cable
Modem.
Chapter 6: Installing the USB Driver for Windows Millennium
This chapter explains how to install the Windows Millennium driver required for a USB connection to the
Cable Modem.
Chapter 7: Installing the USB Driver for Windows 98
This chapter explains how to install the Windows 98 driver required for a USB connection to the Cable
Modem.
•
•
Appendix A: Troubleshooting
This appendix describes some potential problems and solutions regarding use of the Cable Modem.
Appendix B: Windows Help
This appendix describes how you can use Windows Help
Chapter 1: Introduction
What’s in this Guide?
2
Cable Modem with USB and Ethernet Connections
Chapter 2: Getting to Know the Cable Modem
Back Panel Ports
The Cable Modem’s ports are located on the back panel.
Figure 2-1: Back Panel
Power Port
The Power port is where you will connect the included power adapter.
Reset Button
The Reset button allows you to clear the Cable Modem’s connections and set the Cable
Modem to the factory defaults.
Ethernet Port
The Ethernet port allows you to connect the Cable Modem to your PC or other Ethernet
network device using a Category 5 (or better) Ethernet network cable.
USB Port
The USB port allows you to connect the Cable Modem to your PC using the included USB cable.
Cable Port
The Cable port is where you will connect the cable from your Internet Service Provider (ISP).
This is a round coaxial cable, like the one that connects to the back of your cable box or
television.
Chapter 2: Getting to Know the Cable Modem
Back Panel Ports
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Front Panel LEDs
The Cable Modem’s LEDs are located on the front panel.
Figure 2-2: Front Panel
Power
Green. The Power LED lights up when the Cable Modem is powered on. It stays solid after the
self-test. If the LED lights up red, the self-test has failed.
NOTE: If the US and DS LEDs are flashing, the
modem is still operating, but your Internet service
has been disabled by your Internet Service
Provider.
Internet, Online Green. The Online LED flashes when the Cable Modem is establishing a connection to your
cable ISP. It is solidly lit when the Cable Modem is synchronized with your cable ISP.
Internet, DS
Internet, US
Ethernet
Green. The DS (Downstream) LED lights up and flashes when the Cable Modem is trying to
lock on a downstream signal. The LED stays solid when it has locked on the signal.
Green. The US (Upstream) LED lights up and flashes when the Cable Modem is trying to lock
on an upstream signal. The LED stays solid when it has locked on the signal.
NOTE: If the US, DS, and Online LEDs are flashing,
the modem is performing a self-test.
Green. The Ethernet LED lights up when the Cable Modem is connected to your computer or
network through the Ethernet port. It flashes when there is activity on the Ethernet port. The
LED will light up orange when there is a data collision.
USB
Green. The USB LED lights up when the Cable Modem is connected to your computer or
network through the USB port. It flashes when there is activity on the USB port. The LED will
light up orange when the USB is connected and before the driver is installed.
Chapter 2: Getting to Know the Cable Modem
Front Panel LEDs
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Chapter 3: Connecting the Cable Modem
Overview
NOTE: Make sure that you have TCP/IP installed on
You can connect the Cable Modem to your PC using either the Ethernet port or the USB port. If you use the USB
port, you will also have to install a USB driver on your PC. If you are using the Cable Modem’s Ethernet port,
proceed to the “Connection Using the Ethernet Port” section. If you are using the Cable Modem’s USB port,
proceed to the “Connection Using the USB Port” section.
your computer. For more information, refer to
“Appendix B: Windows Help.”
Connection Using the Ethernet Port
1. Power off your PC. If you have an existing cable modem that you are replacing, disconnect it at this time.
2. Connect the coaxial cable from your Internet Service Provider (ISP) or cable company to the Cable port on
the back panel of the Cable Modem. (The other end of the coaxial cable should be connected according to
the ISP or cable company’s instructions.)
Figure 3-1: Connect the Coaxial Cable
3. Connect the included Ethernet network cable to the Ethernet port on the back panel of the Cable Modem.
4. Connect the other end of the Ethernet network cable to the RJ-45 port of your PC’s Ethernet network adapter
or a network device, such as a router, switch, or hub.
5. Connect the included power adapter to the Power port on the back panel of the Cable Modem. Connect the
other end to a standard electrical outlet.
Figure 3-2: Connect the Ethernet Network Cable
6. The Power LED on the front panel of the Cable Modem should light up and remain lit.
7. Power on your PC.
8. Contact your cable ISP to activate your account. Your cable ISP will need the MAC address for the Cable
Modem in order to set up your account. The 12-digit MAC address is printed on a bar code label on the bottom
of the Cable Modem. Once you have given them this number, your cable ISP should be able to activate your
account.
Congratulations! The installation of the Cable Modem is complete.
Figure 3-3: Connect the Power Cable
NOTE: To activate your high-speed Internet account,
you must contact your cable ISP after you have
connected the Cable Modem.
Chapter 3: Connecting the Cable Modem
Overview
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Connection Using the USB Port
1. Power off your PC. If you have an existing cable modem that you are replacing, disconnect it at this time.
2. Connect the coaxial cable from your Internet Service Provider (ISP) or cable company to the Cable port on the
back panel of the Cable Modem. (The other end of the coaxial cable should be connected according to the ISP
or cable company’s instructions.)
Figure 3-4: Connect the Coaxial Cable
3. Connect the included power adapter to the Power port on the back panel of the Cable Modem. Connect the
other end to a standard electrical outlet.
4. The Power LED on the front panel of the Cable Modem should light up and remain lit.
5. Connect the square end of the included USB cable to the USB port on the back panel of the Cable Modem.
6. Connect the rectangular end of the USB cable to your PC’s USB port.
Figure 3-5: Connect the USB Cable
7. Power on your PC. During the boot-up process, your computer should recognize the Cable Modem and
request to install the Cable Modem’s driver. Proceed to the appropriate chapter for instructions on how to
install the USB driver.
•
•
•
If your PC runs Windows XP, proceed to “Chapter 4: Installing the USB Driver for Windows XP.”
If your PC runs Windows 2000, proceed to “Chapter 5: Installing the USB Driver for Windows 2000.”
If your PC runs Windows Millennium, proceed to “Chapter 6: Installing the USB Driver for Windows
Millennium.”
Figure 3-6: Connect the Power Cable
•
If your PC runs Windows 98, proceed to “Chapter 7: Installing the USB Driver for Windows 98.”
Chapter 3: Connecting the Cable Modem
Connection Using the USB Port
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Chapter 4: Installing the USB Driver for Windows XP
Overview
If you are connecting the Cable Modem to your computer using the USB port, follow these instructions to install
the USB driver required for Windows XP.
Instructions for Installing the Driver
1. Power on your computer. Make sure you have administrative rights on your computer; otherwise you cannot
install the driver.
Figure 4-1: Welcome
2. Windows XP will automatically detect the Cable Modem. Insert the User Guide and USB Drivers CD-ROM into
your computer’s CD-ROM drive.
3. On the Welcome screen of the Found New Hardware Wizard, select Install the software automatically
(Recommended), and click the Next button.
4. Please wait while Windows XP finds and automatically installs the driver. When Windows XP has finished
installing the driver, the screen shown in Figure 4-2 will disappear.
5. The Windows XP driver installation is complete. Contact your cable ISP to activate your account. Your cable
ISP will need the MAC address for the Cable Modem in order to set up your account. The 12-digit MAC
address is printed on a bar code label on the bottom of the Cable Modem. Once you have given them this
number, your cable ISP should be able to activate your account.
Figure 4-2: Please wait...
Congratulations! The installation of the Cable Modem is complete.
NOTE: To activate your high-speed Internet account,
you must contact your cable ISP after you have
connected the Cable Modem.
Chapter 4: Installing the USB Driver for Windows XP
Overview
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Chapter 5: Installing the USB Driver for Windows 2000
Overview
If you are connecting the Cable Modem to your computer using the USB port, follow these instructions to install
the USB driver required for Windows 2000.
Instructions for Installing the Driver
1. Power on your computer. Make sure you have administrative rights on your computer; otherwise you cannot
install the driver.
Figure 5-1: Welcome
Figure 5-2: Install Hardware Device Drivers
Figure 5-3: Locate Driver Files
2. Windows 2000 will automatically detect the Cable Modem. Insert the User Guide and USB Drivers CD-ROM
into your computer’s CD-ROM drive.
3. On the Welcome screen of the Found New Hardware Wizard, click the Next button.
4. On the Install Hardware Device Drivers screen, select Search for a suitable driver for my device
(recommended). Then click the Next button.
5. On the Locate Driver Files screen, select CD-ROM drives, and click the Next button.
Chapter 5: Installing the USB Driver for Windows 2000
Overview
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
6. On the Driver Files Search Results screen, click the Next button.
7. When Windows 2000 has finished installing the driver, the Completing the Found New Hardware Wizard
screen will appear. Click the Finish button.
8. The Windows 2000 driver installation is complete. Contact your cable ISP to activate your account. Your cable
ISP will need the MAC address for the Cable Modem in order to set up your account. The 12-digit MAC
address is printed on a bar code label on the bottom of the Cable Modem. Once you have given them this
number, your cable ISP should be able to activate your account.
Congratulations! The installation of the Cable Modem is complete.
Figure 5-4: Driver Files Search Results
Figure 5-5: Driver Installation Complete
NOTE: To activate your high-speed Internet account,
you must contact your cable ISP after you have
connected the Cable Modem.
Chapter 5: Installing the USB Driver for Windows 2000
Instructions for Installing the Driver
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Chapter 6: Installing the USB Driver for Windows
Millennium
Overview
If you are connecting the Cable Modem to your computer using the USB port, follow these instructions to install
the USB driver required for Windows Millennium.
Instructions for Installing the Driver
1. Power on your computer. Make sure you have administrative rights on your computer; otherwise you cannot
Figure 6-1: Add New Hardware Wizard
install the driver.
2. Windows Millennium will automatically detect the Cable Modem. Insert the User Guide and USB Drivers CD-
ROM into your computer’s CD-ROM drive.
3. On the first screen of the Add New Hardware Wizard, select Automatic search for a better driver
(Recommended). Then click the Next button.
4. Please wait while Windows Millennium finds and automatically installs the driver. When Windows Millennium
has finished installing the driver, click the Finish button.
5. The Windows Millennium driver installation is complete. Contact your cable ISP to activate your account. Your
cable ISP will need the MAC address for the Cable Modem in order to set up your account. The 12-digit MAC
address is printed on a bar code label on the bottom of the Cable Modem. Once you have given them this
number, your cable ISP should be able to activate your account.
Figure 6-2: Driver Installation Complete
Congratulations! The installation of the Cable Modem is complete.
NOTE: To activate your high-speed Internet account,
you must contact your cable ISP after you have
connected the Cable Modem.
Chapter 6: Installing the USB Driver for Windows Millennium
Overview
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Chapter 7: Installing the Driver for Windows 98
Overview
If you are connecting the Cable Modem to your computer using the USB port, follow these instructions to install
the USB driver required for Windows 98.
Instructions for Installing the Driver
1. Power on your computer. Make sure you have administrative rights on your computer; otherwise you cannot
install the driver.
Figure 7-1: Add New Hardware Wizard
2. Windows 98 will automatically detect the Cable Modem. Insert the User Guide and USB Drivers CD-ROM into
your computer’s CD-ROM drive.
3. On the first screen of the Add New Hardware Wizard, click the Next button.
4. Select Search for the best driver for your device (Recommended). Then click the Next button.
5. Select CD-ROM drive. Then click the Next button.
Figure 7-2: Search for Driver
Figure 7-3: Select CD-ROM Drive
Chapter 7: Installing the Driver for Windows 98
Overview
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
6. Select The updated driver (Recommended). Then click the Next button.
7. After Windows has found the driver, click the Next button.
8. When Windows 98 has finished installing the driver, click the Finish button.
9. The Windows 98 driver installation is complete. Contact your cable ISP to activate your account. Your cable
ISP will need the MAC address for the Cable Modem in order to set up your account. The 12-digit MAC
address is printed on a bar code label on the bottom of the Cable Modem. Once you have given them this
number, your cable ISP should be able to activate your account.
Congratulations! The installation of the Cable Modem is complete.
Figure 7-4: Select Updated Driver
Figure 7-5: Location of Driver
Figure 7-6: Driver Installation Complete
NOTE: To activate your high-speed Internet account,
you must contact your cable ISP after you have
connected the Cable Modem.
Chapter 7: Installing the Driver for Windows 98
Instructions for Installing the Driver
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Appendix A: Troubleshooting
This appendix provides solutions to problems that may occur during the installation and operation of the Cable
Modem. Read the description below to solve your problems. If you can't find an answer here, check the Linksys
Common Problems and Solutions
1. I cannot access my e-mail or Internet service.
Go through this checklist until your problem is solved:
•
Make sure all of your connections are secure.
1. The Ethernet cable should be inserted completely into both the computer’s network adapter and the
Ethernet port on the back panel of the Cable Modem.
2. If you are using the Cable Modem’s USB port, check the USB connections to the Cable Modem and
your PC.
3. Check all cables between your computer and the Cable Modem for frays, breaks, or exposed wiring.
4. Make sure your power adapter is properly plugged into both the Cable Modem and the electrical
outlet or surge protector. If the Cable Modem is properly connected, the Power and Cable LEDs on the
Cable Modem should be solidly lit. The Activity LED should be solid or flashing.
Press the Reset button on the back panel of the Cable Modem. Using an object with a small tip, such as a
pen, push the button until you feel it click. Then try reconnecting to the Internet.
Call your cable ISP to verify that their service is two-way. This Cable Modem is designed for use with two-
way cable networks.
•
•
•
If you installed the Cable Modem using the Ethernet port, make sure the computer’s network adapter is
operating correctly. Make sure the adapter is listed in the Windows Device Manager and has no conflicts.
For more information, refer to Windows Help.
•
•
Make sure TCP/IP is the default protocol used by your computer. For more information, refer to “Appendix
B: Windows Help.”
If you are using a cable line splitter so you can connect the Cable Modem and a television at the same
time, remove the splitter and reconnect your cables so that the Cable Modem is connected directly to the
cable wall jack. Then try reconnecting to the Internet.
2. The Online LED never stops flashing.
Go through this checklist until your problem is solved:
•
Make sure the Cable Modem’s MAC address has been registered with your cable ISP. In order for the
Cable Modem to work, you must call and have the ISP activate the Cable Modem by registering its MAC
address. You can find the MAC address on a label located on the Cable Modem’s bottom panel.
Make sure the coaxial cable is firmly attached between the Cable Modem and the wall jack.
•
Appendix A: Troubleshooting
Common Problems and Solutions
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
•
The signal from your cable company’s equipment may be too weak or the cable line may not be properly
attached to the Cable Modem. If the cable line is properly connected to the Cable Modem, then call your
cable company to verify whether a weak signal may be the problem.
3. All of the LEDs on the Cable Modem indicate that the Cable Modem is functioning properly, but I still
can’t access the Internet.
Go through this checklist until your problem is solved:
•
If the Power and Online LEDs are lit but not flashing, then the Cable Modem is operating properly. Power
your computer off and back on again. This will cause your computer to re-establish communications with
your cable ISP.
•
•
Press the Reset button on the back panel of the Cable Modem. Using an object with a small tip, such as a
pen, push the button until you feel it click. Then try reconnecting to the Internet.
Make sure TCP/IP is the default protocol used by your computer. For more information, refer to “Appendix
B: Windows Help.”
4. The power on the Cable Modem goes on and off sporadically.
You may be using the wrong power adapter. Make sure the power adapter you are using is the one included
with the Cable Modem.
Appendix A: Troubleshooting
Common Problems and Solutions
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Appendix B: Windows Help
Most Linksys products require Microsoft Windows. Windows is the most used operating system in the world and
comes with many features that help make networking easier. These features can be accessed through Windows
Help and are described in this appendix.
TCP/IP
Before a computer can communicate with a network router, TCP/IP must be enabled. TCP/IP is a set of
instructions, or protocol, all PCs follow to communicate over a network. This is true for wireless networks as well.
Your PCs will not be able to utilize wireless networking without having TCP/IP enabled. Windows Help provides
complete instructions on enabling TCP/IP.
Shared Resources
If you wish to share printers, folder, or files over your network, Windows Help provides complete instructions on
utilizing shared resources.
Network Neighborhood/My Network Places
Other PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the
version of Windows you're running). Windows Help provides complete instructions on adding PCs to your
network.
Appendix B: Windows Help
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Appendix C: Glossary
802.11a - A wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an
operating frequency of 5GHz.
802.11b - A wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an
operating frequency of 2.4GHz.
802.11g - A wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating
frequency of 2.4GHz, and backward compatibility with 802.11b devices.
Access Point - A device that allows wireless-equipped computers and other devices to communicate with a
wired network. Also used to expand the range of a wireless network.
Adapter - A device that adds network functionality to your PC.
Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of
an access point.
AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption.
Backbone - The part of a network that connects most of the systems and networks together, and handles the
most data.
Bandwidth - The transmission capacity of a given device or network.
Beacon Interval - Data transmitted on your wireless network that keeps the network synchronized.
Bit - A binary digit.
Boot - To start a device and cause it to start executing instructions.
Bridge - A device that connects different networks.
Broadband - An always-on, fast Internet connection.
Browser - An application program that provides a way to look at and interact with all the information on the
World Wide Web.
Appendix C: Glossary
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Buffer - A shared or assigned memory area that is used to support and coordinate different computing and
networking activities so one isn't held up by the other.
Byte - A unit of data that is usually eight bits long
Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the
Internet.
CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - A method of data transfer that is used to prevent
data collisions.
CTS (Clear To Send) - A signal sent by a wireless device, signifying that it is ready to receive data.
Daisy Chain - A method used to connect devices in a series, one after the other.
Database - A collection of data that is organized so that its contents can easily be accessed, managed, and
updated.
DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a
Default Gateway - A device that forwards Internet traffic from your local area network.
DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign
temporary IP addresses to network computers by "leasing" an IP address to a user for a limited amount of time,
instead of assigning permanent IP addresses.
DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be "seen" from
the Internet.
DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP
addresses.
Domain - A specific name for a network of computers.
Download - To receive a file transmitted over a network.
DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines.
DSSS (Direct-Sequence Spread-Spectrum) - Frequency transmission with a redundant bit pattern resulting in a
lower probability of information being lost in transit.
Appendix C: Glossary
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
DTIM (Delivery Traffic Indication Message) - A message included in data packets that can increase wireless
efficiency.
Dynamic IP Address - A temporary IP address assigned by a DHCP server.
EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access.
Many specific authentication methods work within this framework.
EAP-PEAP (Extensible Authentication Protocol-Protected Extensible Authentication Protocol) - A mutual
authentication method that uses a combination of digital certificates and another system, such as passwords.
EAP-TLS (Extensible Authentication Protocol-Transport Layer Security) - A mutual authentication method that
uses digital certificates.
Encryption - Encoding data transmitted in a network.
Ethernet - A networking protocol that specifies how data is placed on and retrieved from a common transmission
medium.
Finger - A program that tells you the name associated with an e-mail address.
Firewall - A set of related programs located at a network gateway server that protects the resources of a
network from users from other networks.
Firmware - The programming code that runs a networking device.
Fragmentation -Breaking a packet into smaller units when transmitting over a network medium that cannot
support the original size of the packet.
FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network.
Full Duplex - The ability of a networking device to receive and transmit data simultaneously.
Gateway - A device that interconnects networks with different, incompatible communications protocols.
Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a
time.
Hardware - The physical aspect of computers, telecommunications, and other information technology devices.
HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World
Wide Web.
Appendix C: Glossary
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Infrastructure - A wireless network that is bridged to a wired network via an access point.
IP (Internet Protocol) - A protocol used to send data over a network.
IP Address - The address used to identify a computer or device on a network.
IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device.
IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer.
ISM band - Radio bandwidth utilized in wireless transmissions.
ISP (Internet Service Provider) - A company that provides access to the Internet.
LAN - The computers and networking products that make up your local network.
LEAP (Lightweight Extensible Authentication Protocol) - A mutual authentication method that uses a username
and password system.
MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking
device.
Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission.
mIRC - An Internet Relay Chat program that runs under Windows.
Multicasting - Sending data to a group of destinations at once.
NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different
IP address for the Internet.
NAT (Network Address Translation) Traversal -A method of enabling specialized applications, such as Internet
phone calls, video, and audio, to travel between your local network and the Internet. STUN is a specific type of
NAT traversal.
Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or
transmission between users.
NNTP (Network News Transfer Protocol) - The protocol used to connect to Usenet groups on the Internet.
Node - A network junction or connection point, typically a computer or work station.
Appendix C: Glossary
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
OFDM (Orthogonal Frequency Division Multiplexing) - Frequency transmission that separates the data stream
into a number of lower-speed data streams, which are then transmitted in parallel to prevent information from
being lost in transit.
Packet - A unit of data sent over a network.
Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically
generating the WEP encryption keys for Linksys products.
PEAP (Protected Extensible Authentication Protocol) - A mutual authentication method that uses a combination
of digital certificates and another system, such as passwords.
Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online.
POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet.
Port - The connection point on a computer or networking device used for plugging in cables or adapters.
Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power.
PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication
(username and password) in addition to data transport.
PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be
tunneled through an IP network. This protocol is also used as a type of broadband connection in Europe.
Preamble - Part of the wireless signal that synchronizes network traffic.
RADIUS (Remote Authentication Dial-In User Service) - A protocol that uses an authentication server to control
network access.
RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires.
Roaming - The ability to take a wireless device from one access point's range to another without losing the
connection.
Router - A networking device that connects multiple networks together.
RTP (Real-time Transport Protocol) - A protocol that enables specialized applications, such as Internet phone
calls, video, and audio, to occur in real time.
RTS (Request To Send) - A networking method of coordinating large packets through the RTS Threshold setting.
Appendix C: Glossary
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Server - Any computer whose function in a network is to provide user access to files, printing, communications,
and other services.
SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet.
SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol.
Software - Instructions for the computer. A series of instructions that performs a particular task is called a
"program".
SOHO (Small Office/Home Office) - Market segment of professionals who work at home or in small offices.
SPI (Stateful Packet Inspection) Firewall - A technology that inspects incoming packets of information before
allowing them to enter the network.
Spread Spectrum - Wideband radio frequency technique used for more reliable and secure data transmission.
SSID (Service Set IDentifier) - Your wireless network's name.
Static IP Address - A fixed address assigned to a computer or device that is connected to a network.
Static Routing - Forwarding data in a network via a fixed path.
STUN (Simple Traversal of UDP through NATs) - A protocol that enables specialized applications, such as Internet
phone calls, video, and audio, to travel between your local network and the Internet. STUN is a specific type of
NAT traversal.
Subnet Mask - An address code that determines the size of the network.
Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of
devices to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an
electrical circuit.
TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement
from the recipient of data sent.
TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to communicate over a
network.
Telnet - A user command and TCP/IP protocol used for accessing remote PCs.
Appendix C: Glossary
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that has no directory or password
capability.
Throughput - The amount of data moved successfully from one node to another in a given time period.
TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for
each packet transmitted.
Topology - The physical layout of a network.
TX Rate - Transmission Rate.
UDP (User Datagram Protocol) - A network protocol for transmitting data that does not require acknowledgement
from the recipient of the data that is sent.
Upgrade - To replace existing software or firmware with a newer version.
Upload - To transmit a file over a network.
URL (Uniform Resource Locator) - The address of a file located on the Internet.
VPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another
over the Internet.
WAN (Wide Area Network)- The Internet.
WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for
greater security.
WINIPCFG - A Windows 98 and Me utility that displays the IP address for a particular networking device.
WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with
each other wirelessly.
WPA (Wi-Fi Protected Access) - a wireless security protocol using TKIP (Temporal Key Integrity Protocol)
encryption, which can be used in conjunction with a RADIUS server.
Appendix C: Glossary
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Appendix D: Specifications
Model
BEFCMU10 v4
Standards
DOCSIS 1.0, DOCSIS 1.1 Certified, DOCSIS 2.0 Certified, IEEE 802.3,
IEEE 802.3u, USB 1.1
Ports
Ethernet, USB, Cable
Reset
Buttons
Cabling Type
Cable: F-type female 75 ohm
Ethernet: 10/100 RJ-45 Port
USB: USB Type B Port
LEDs
Power, Internet DS, Internet US, Internet Online, Ethernet, USB
Dimensions
(W x H x D)
7.32" x 1.89" x 6.50"
(186 mm x 48 mm x 165 mm)
Unit Weight
13.76 oz. (0.39 kg)
Power
12VDC, 1A
Certifications
Operating Temp.
Storage Temp.
Operating Humidity
Storage Humidity
DOCSIS 1.1, DOCSIS 2.0, FCC Part 15 Class B, UL 1950, CE
32ºF to 104ºF (0ºC to 40ºC)
-4ºF to 158ºF (-20ºC to 70ºC)
20% to 90%, Non-Condensing
0% to 90%, Non-Condensing
Appendix D: Specifications
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Appendix E: Warranty Information
LIMITED WARRANTY
Linksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially
free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under
this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any
rebates. This limited warranty extends only to the original purchaser.
If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return
Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are
requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a
copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You
are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You
only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling
charges.
ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED
TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives
You specific legal rights, and You may also have other rights which vary by jurisdiction.
This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated,
repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal
physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new
techniques for intruding upon and attacking networks, Linksys does not warrant that the Product will be free of
vulnerability to intrusion or attack.
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR
PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY
OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT
(INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT
WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even
if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.
24
Appendix E: Warranty Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Appendix F: Regulatory Information
FCC STATEMENT
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which is found by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment or devices
Connect the equipment to an outlet other than the receiver's
Consult a dealer or an experienced radio/TV technician for assistance
INDUSTRY CANADA (CANADA)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
EC DECLARATION OF CONFORMITY (EUROPE)
In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, and Amendment Directive
93/68/EEC, this product meets the requirements of the following standards:
•
•
EN55022 Emission
EN55024 Immunity
Appendix F: Regulatory Information
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Modem with USB and Ethernet Connections
Appendix G: Contact Information
Need to contact Linksys?
Visit us online for information on the latest products and updates
to your existing products at:
ftp.linksys.com
Can't find information about a product you want to buy
on the web? Do you want to know more about networking
with Linksys products? Give our advice line a call at:
Or fax your request in to:
800-546-5797 (LINKSYS)
949-261-8868
If you experience problems with any Linksys product,
you can call us at:
800-326-7114
Don't wish to call? You can e-mail us at:
If any Linksys product proves defective during its warranty period,
you can call the Linksys Return Merchandise Authorization
department for obtaining a Return Authorization Number at:
(Details on Warranty and RMA issues can be found in the Warranty
Information section in this Guide.)
949-261-1288
26
Appendix G: Contact Information
Download from Www.Somanuals.com. All Manuals Search And Download.
|