C H A P T E R
3
Installing the Cisco Global Site
Selector 4490
This chapter explains how to install a Cisco Global Site Selector 4490 in an
equipment rack. It also provides general instructions for installing a GSS 4490 on
a table or workbench.
This chapter contains the following major sections:
•
•
•
•
•
•
•
•
Before you begin the installation be sure to read:
•
•
•
Appendix C, Regulatory Compliance and EMI Class A Warnings
Regulatory Compliance and Safety Information for the Cisco Global Site
Selector 4490
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Tools and Parts Required
If the Product is Damaged
If any portion of the unit or component is damaged in transit, forward an
immediate request to the delivering carrier to perform an inspection of the product
and to prepare a damage report. Save the container and all packing materials until
the contents are verified.
Concurrently, report the nature and extent of the damage to Customer Service.
Report the problem or deficiency to Customer Service along with the model
number and serial number. Upon receipt of this information, you will be provided
with service instructions, or a Return Material Authorization (RMA) number and
shipping information. To obtain assistance, refer to the “Preface”.
Tools and Parts Required
Your Global Site Selector 4490 comes with the following rack kits suitable for
mounting the GSS 4490 in a 19-inch (48.26-cm) equipment rack:
•
•
A sliding rail four-post rack-mount kit
A two-post rack-mount kit
To install the Global Site Selector 4490 in a rack you need the following parts and
tools:
•
•
•
Flat-blade screwdriver
Phillips screwdriver
One rack-mount kit
Figure 3-1 identifies the items included with the four-post rack. If any items are
missing or damaged, contact your place of purchase.
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Tools and Parts Required
Figure 3-1 Four-Post Rack Installation Kit
1
2
3
4
5
6
7
1
Slide rail assemblies (2)
M4 screws (6)
2
4
6
M3.5 screws with lock washers (3)
M6 screws (10)
3
5
7
Clip nuts (10)
Cage nuts (10)
Cage nut insertion tool (1)
Note
The right and left slide rails are identical.
Cisco Global Site Selector 4490 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
78-15755-01
3 -4
Chapter 3 Installing the Cisco Global Site Selector 4490
Installing Your Unit
Installing Your Unit
Place the unit in the desired location. You can mount it in a rack for your
convenience, or place it on a solid, stable surface. If you do not plan to install the
GSS 4490 in an equipment rack, proceed to the “Installing the Chassis on a
Workbench or Tabletop” section.
Racks are marked in vertical increments of 1.75 inches (4.44 cm). Each increment
is referred to as a rack unit (RU). A 1-RU device is 1.75 inches (4.44 cm) tall.
Warning
To prevent bodily injury when mounting or servicing this unit in a rack, you must
take special precautions to ensure that the system remains stable. The
following guidelines are provided to ensure your safety:
•
•
This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
When mounting this unit in a partially filled rack, load the rack from the
bottom to the top with the heaviest component at the bottom of the rack.
If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
This section contains the following procedures:
•
•
•
Cisco Global Site Selector 4490 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
78-15755-01
3 -5
Chapter 3 Installing the Cisco Global Site Selector 4490
Installing Your Unit
Installing the Chassis in a Four-Post Rack
To install the Global Site Selector 4490 in a four-post rack, follow these steps:
1. Select a 1-RU-size location in the rack to mount the GSS 4490. If the rack
holes are not threaded, install a clip nut or cage nut in the top and bottom
front side of the rack (as viewed from the front of the GSS 4490). Install a
clip nut or cage nut in the corresponding positions on the rear of the rack.
Repeat this step for the left front side of the rack and the corresponding
location on the rear of the rack.
Figure 3-2 Installing Clip Nuts or Cage Nuts in a Non-Threaded Rack
1
2
1
Cage nuts
2
Clip nuts
Cisco Global Site Selector 4490 Hardware Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
78-15755-01
3 -6
Chapter 3 Installing the Cisco Global Site Selector 4490
Installing Your Unit
2. Remove the inner slide rails from the slide rail assemblies by pressing the
Figure 3-3 Rem oving the Inner Slide Rail
3
2
1
1
3
Slide rail assembly
Inner slide rail
2
Release latch
indicated by the arrow on the side of the GSS 4490. Use two M4 screws to
secure the inner slide rail to the GSS 4490.
Repeat this step to attach the other inner slide rail to the GSS 4490.
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Installing Your Unit
Figure 3-4 Attaching the Inner Slide Rail to the GSS 4490
1
4. Insert the tab on the front of the slide rail assembly through the center hole
between the two clip nuts or cage nuts on the front flange.
5. Align the slide rail assembly to the front flange on the rack.
Repeat step 4 and this step to install the other slide rail assembly.
Note
If it is necessary to adjust the length of the slide rail, loosen the
adjustment screw on the rear of the slide rail; then adjust the length of the
6. Insert and tighten two M6 screws to secure the slide rail to the front flange
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Installing Your Unit
Figure 3-5 Attaching the Slide Rails to the Rack
Front
Rear
1
2
3
1
Tab
Rear flange
2
Adjustment screw
3
7. Insert and tighten two M6 screws to secure the other slide rail assembly to the
rear flange.
8. Align and insert the inner slide rails into the slide rail assemblies until they
lock into place.
9. Slide the GSS 4490 into the rack until it locks into place.
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Installing Your Unit
of the GSS 4490 to secure it to the rack.
Figure 3-6 Inserting the Inner Slide Rails
1
1
Release tab
11. Attach the power cord and the Ethernet cables to the GSS 4490.
Because the GSS 4490 does not contain cable retention brackets or cable
strain relief brackets, you must first bundle the external cables before you
route them. Use the remaining two cable straps to bundle the cables.
Note
Leave sufficient slack in the cables to allow for sliding the GSS 4490 in
or out of the rack.
To remove the GSS 4490 from the rack, reverse these instructions.
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -1 0
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Installing Your Unit
Installing the Chassis in a Two-Post Rack
To install the Global Site Selector 4490 in a two-post rack, follow these steps:
indicated by the arrow on the side of the GSS 4490. Use two M4 x 8 screws
to secure the bracket to the GSS 4490.
Repeat this step to attach the other bracket to the GSS 4490.
Figure 3-7 Attaching a Bracket to the Right Side of the GSS 4490
Cisco GSS 4490
SERIES
!
3
2
1
1
3
Alignment marker
M4 x 8 screws
2
Bracket
2. Select a location in the rack to mount the GSS 4490, then position the
GSS 4490 and brackets in the rack.
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -1 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Installing Your Unit
3. Align the right side bracket on the GSS 4490 to the two-post rack, then insert
GSS 4490 to the rack.
Note
Due to variations in rack size and rack holes, Cisco Systems does not
provide the two-post rack mounting screws in the rack kit.
Repeat this step to secure the left side bracket to the rack.
Figure 3-8 Attaching the GSS 4490 to the Two-Post Rack
Cisco GSS 4490
SERIES
!
1
1
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -1 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Installing Your Unit
Installing the Chassis on a Workbench or Tabletop
When you install a Global Site Selector 4490 on a workbench or tabletop, ensure
that the surface is clean and in a safe location and that you have considered the
following:
•
The chassis should be installed off the floor. (Dust that accumulates on the
floor is drawn into the interior of the chassis by the cooling fans. Excessive
dust inside the GSS 4490 can cause overtemperature conditions and
component failures.)
•
•
There must be approximately 19 inches (48.26 cm) of clearance at the front
and rear of the chassis for accessing network cables or equipment.
The GSS 4490 must receive adequate ventilation (it is not being installed in
an enclosed cabinet where ventilation is inadequate).
Follow these steps to install the GSS 4490 on a workbench or tabletop:
1. Remove any debris and dust from the tabletop or workbench, as well as from
the surrounding area. Also make sure that your path between the GSS 4490
and its new location is unobstructed.
2. Attach the rubber feet to the bottom of the chassis. The rubber feet have an
adhesive backing. Peel the protective tape off the adhesive and stick the feet
to the bottom of a clean chassis surface. Place one foot in each corner.
3. Place the chassis on the tabletop or workbench.
4. Ensure that no exhaust air from other equipment will be drawn into the
chassis. Also, ensure that there is adequate clearance at the front and rear of
the chassis.
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -1 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Connecting Cables
Connecting Cables
To connect network and console cables to your GSS 4490, follow these steps.
1. For network connections, insert a Category 5 UTP cable into the Ethernet 0
2. Connect the other end of the network cable to a hub or switch in your
network.
3. For console connections, plug the cable into the console port on the
GSS 4490 back panel.
4. Connect the other end of the console cable to a console or a
communications server.
Figure 3-9 Global Site Selector 4490 Back Panel Ports and Receptacles
1
2
3
4
1
3
AC power receptacle
Ethernet 1 receptacle
2
4
Ethernet 0 receptacle
Console port
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -1 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Connecting Power
Connecting Power
To connect power to your AC system, follow these steps:
2. Plug the AC power cord into the power cord receptacle at the rear of the
3. Connect the other end of the power cord to a power source at your
installation site.
4. Power up all externally connected devices.
5. Press the power control button on the front of the GSS 4490.
Booting the System
When you power up a Cisco Global Site Selector, the boot process:
•
•
•
•
•
•
Performs hardware initialization and power-on self tests
Initializes the BIOS
Initializes the Linux boot manager, LILO (Linux Loader)
Boots the GSS image (kernel and software)
Displays the startup banner and splash screen for strong encryption
Prompts you to log in to the GSS
Note
While the GSS 4490 is powering up, the green power LED on the front of the
GSS 4490 is on.
At this point you are ready to use the GSS device. Refer to the Cisco Global Site
Selector Configuration Guide and the Cisco Global Site Selector Command
Reference for details on setting up, configuring, and using the GSS device.
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -1 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Checking the Front Panel LEDs
If you are booting the GSS 4490 for the first time and the system boots without a
startup-configuration file, a setup script automatically runs to quickly guide you
through the process of initially configuring the GSS. Refer to the Global Site
Selector Configuration Guide, Chapter 2, Setting Up Your GSS and GSSM, for
details.
Checking the Front Panel LEDs
When the Global Site Selector 4490 is up and running, observe the front panel
describes their function.
Figure 3-10 Front Panel LEDs
1
2
3
4
1
3
CD-ROM drive activity
Hard disk drive activity
2
4
System error
Power
Table 3-1 Front Panel LEDs
LED
Color
State
Description
CD-ROM drive
activity
Green
On
Indicates that the CD-ROM drive is in use.
System error
Amber
On
Indicates that a system error has occurred. An LED on
the diagnostic LED panel will also be on to further
isolate the error.
Hard disk drive
activity
Green
Flashing Indicates that the associated hard disk drive is in use.
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -1 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Removing or Replacing a Cisco Global Site Selector 4490
Table 3-1 Front Panel LEDs (continued)
LED
Color
State
Description
Indicates that the GSS 4490 has power.
Power
Green
On
Flashing Indicates that the GSS 4490 is in standby mode.
Removing or Replacing a Cisco Global Site
Selector 4490
Warning
Before working on a system that has an On/Off switch, turn OFF the power and
unplug the power cord.
Warning
Ultimate disposal of this product should be handled according to all national
laws and regulations.
Before removing or replacing a GSS 4490, you should logically remove the GSS
from the network before physically removing it.
To logically remove a GSS 4490 from the network, follow these steps:
1. Log on to the CLI (see the Cisco Global Site Selector Configuration Guide).
2. At the CLI prompt, enable privileged EXEC mode and then global
configuration mode on the device. For example:
localhost.localdomain> enable
3. Use the gss stop command to stop the GSS software running on the
GSS 4490. For example:
localhost.localdomain# gss stop
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -1 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Removing or Replacing a Cisco Global Site Selector 4490
4. Use the gss disable command to disable the selected GSS 4490 and remove
any existing configuration, including deleting the GSSM database from the
GSS device. This option returns the GSS 4490 to the initial, unenabled state.
For example:
localhost.localdomain# gss disable
localhost.localdomain# shutdown
5. If you are logically removing a GSS or a standby GSSM from the network,
access the primary GSSM graphical user interface and click the Resources
tab.
Note
To logically remove the primary GSSM from the network, you must
enable the standby GSSM in the role of the primary GSSM using the gss
enable gssm-primary CLI command. You may then access the newly
assigned primary GSSM and logically remove the GSSM from the
network. Refer to the Cisco Global Site Selector Configuration Guide for
details.
6. Click the Global Site Selectors navigation link. The Global Site Selectors list
page appears.
7. From the Global Site Selectors list, click the Modify GSS icon located to the
left of the GSS device you want to delete. The Modifying GSS details page
appears.
8. Click the Delete icon in the upper right corner of the page. The GSS software
prompts you to confirm your decision to delete the GSS device.
9. Click OK to confirm your decision. You return to the Global Site Selectors
list page with the deleted device removed from the list.
To physically remove a GSS 4490 from your network, follow these steps:
1. Power down the GSS 4490.
2. Disconnect the power cords and network cables.
3. Physically remove the chassis from the rack.
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -1 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Removing or Replacing a Cisco Global Site Selector 4490
To physically replace a GSS 4490, follow these steps:
1. Remove the GSS 4490 from the network (as described above).
2. Install the new GSS 4490 and configure it using the same configuration
parameters (such as IP address) that you used for the removed GSS 4490.
Refer to the Cisco Global Site Selector Configuration Guide, Chapter 2,
Setting Up Your GSS for details.
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -1 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the Cisco Global Site Selector 4490
Removing or Replacing a Cisco Global Site Selector 4490
Cisco Global Site Selector 4490 Hardware Installation Guide
78-15755-01
3 -2 0
Download from Www.Somanuals.com. All Manuals Search And Download.
|