®
Chromalox
DIVISION
SALES
SECTION
4
VTS
(Supersedes PG435 )
PG435-1
REFERENCE
161-304901-003
DATE
NOVEMBER, 2003
STAR-05A, -06A and -14A Cart Kit
For Conversion of Fixed Style to Portable Style
STAR-05 Portable Heater
After Conversion
See Page 2 – Fig. 2
STAR-05A Fixed Heater
Before Conversion
See Page 2 – Fig. 1
STAR-06A Portable Heater
After Conversion
See Page 3 – Fig. 2
STAR-06A Fixed Heater
Before Conversion
See Page 3 – Fig. 1
STAR-14A Portable Heater
After Conversion
See Page 4 – Fig. 2
STAR-14A Fixed Heater
Before Conversion
See Page 4 – Fig. 1
© 2010 Chromalox, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
6.0 kW UNIT CONVERSION INSTRUCTIONS
INSTRUCTIONS FOR CONVERTING
A FIXED STYLE INTO A PORTABLE STYLE
(Installation of Cart making it a Portable Heater Voids UL Listing)
11-1/2"
1. The kit (168-053169-079) that converts a 6.0 KW fixed style radiant
heater includes the following parts. Verify that all parts are included, if
not, contact the Chromalox Service Department at 1-800-368-2493.
(1) Lower Leg
(2) Axle
(10) 1/4-20 x 1/2” Long Bolt (4 Req’d)
(11) 1/4-20 Square nut (4 Req’d)
(12) Pop Rivet (4 Req’d)
(13) No. 10 Sheet Metal Screw ( Req’d)
(14) 3/8-16 x 1-1/2” Long Bolts (2 Req’d)
(15) 3/8-16 Nuts (2 Req’d)
(16) 3/8 Lockwashers (2 Req’d)
(17) 10-32 x 1/2” Long Self Tapping
Screw (2 Req’d)
(3) Wheel (2 Req’d)
(4) Cap (2 Req’d)
(5) Upper Handle
(6) Front Leg
(7) Grip
23-5/8"
(8) Grille
(9) Baffle
2. Using hammer tap cap (4) onto one end of axle (2). Slide one wheel
(3) onto axle. Slide end of axle through both holes of lower leg (1).
Slide remaining wheel onto portion of axle protruding through lower
leg. Tap cap on axle.
32-1/2"
3. Remove Lower Bracket by removing nuts and washers.
6.0kW Fixed Style Heater
4. Slide the two (2) 3/8” bolts in the outer extrusions to the 4-1/2”
dimension and the one (1) 3/8” bolt in the center extrusion to the 8-
15/16” dimension.
3
5. Place lower leg assy made in step 2 onto the three (3) bolts. Secure in
2
place with washers and nuts removed in step 3.
6. Loosen three nuts on upper bracket and reposition to the 3” dimension
2
9
shown.
7. Slide the two 3/8-16 x 1-1/2” long bolts (14) into the top center extru-
sion. Locate one at 3/4” and the other at 2-1/4” as shown.
8. Place upper handle (5) onto two bolts. Secure in place with washers
5
and nuts provided.
6
9. Slide grip (7) onto end of upper handle (5).
10.Stand heater vertically. If heater does not sit evenly, loosen nuts that
5
1
secure lower leg assy and adjust accordingly.
6
11.Rotate heater back until handle (5) is on floor.
Scribe
Line on
Extrusion
12.Install front leg (6) with two 10-32 x 1/2” long self tapping
screws (17).
13.Install baffle (8) using pop rivets, if pop rivet gun is not available use
the No. 10 sheet metal screws.
14.Place grille prongs into slots of reflector using a counterclockwise rota-
tion see Detail A. Insert 1/4-20 screws through looped end of grille
with 1/4-20 square nut on opposite side. Tighten screws with screw
driver.
15.If fixed heater is being converted to a portable by the factory, then drill
2x Loop of Grill
out nameplate rivets and replace nameplate with 196-891789-004.
7
10
4
6.0 kW Fixed Style Heater
Modified to add cart, baffle and grille
8
2x Prong of Grill
3
Download from Www.Somanuals.com. All Manuals Search And Download.
13.5 kW UNIT CONVERSION INSTRUCTIONS
INSTRUCTIONS FOR CONVERTING
A FIXED STYLE INTO A PORTABLE STYLE
(Installation of Cart making it a Portable Heater Voids UL Listing)
11-1/2"
1. The kit (168-053169-057) that converts a 13.5 kW fixed style radiant heater
into a protable includes the following parts. Verify that all parts are included,
if not, contact the Chromalox Service Department at 1-800-368-2493.
(1)Lower Leg
(7) Grille (2 Req’d)
(2)Axle
(8) Baffle
(3)Wheel (2 Req’d)
(4)Cap (2 Req’d)
(5)Upper Handle
(6)Grip (2 Req’d)
(9) 1/4-20 x 1/2” long bolt (4 Req’d)
(10) 1/2-20 Square nut (4 Req’d)
(11) Pop Rivet (6 Req’d)
(12) No. 10 Sheet Metal Screw (6 Req’d)
23-5/8"
2. Using hammer tap cap (4) onto one end of axle (2). Slide one wheel (3)
onto axle. Slide end of axle through both holes of lower leg (1). Slide
remaining wheel onto portion of axle protruding through lower leg. Tap
cap on axle.
3. Remove Lower Bracket by removing nuts and washers.
55-5/8"
4. Slide the two 3/8” bolts in the outer extrusions to the 7-3/32” dimension
and the one 3/8” bolt in the center extrusion to the 11-17/32” dimension.
13.5 kW Fixed Style Heater
5. Place lower leg assy made in step 2 onto the three bolts. Secure in place
with washers and nuts removed in step 3.
6. Remove upper bracket by removing nuts and washers.
7. Place upper handle (5) onto three bolts. secure in place with washers and
nuts removed in step 6.
8. Slide grips (6) onto ends of upper handle.
9. Stand heater vertically. If heater does not sit evenly, loosen nuts that
secure lower leg assy and adjust accordingly.
3
6
5
10. Rotate heater back until handle (5) is on floor.
11. Install baffle (8) using pop rivets, if pop rivet gun is not available use the
NO. 10 sheet metal screws.
3
12. Place grille prongs into slots of reflector using a counterclockwise rotation
see Detail A. Insert 1/4-20 bolts (9) through looped end of grille with 1/4-
20 square not (10) on opposite side. Tighten screws with screw driver.
2
2
13. Install remaining grille in same manner as step 12.
14. If fixed heater is being converted to a portable by the factory, then drill out
nameplate rivets and replace nameplate with 196-891789-004.
5
6
7
1
9
2x Loop of Grill
4
5
6
3
Scribe Line
2x Prong of Grill
on Extrusion
4
13.5 kW Fixed Style Heater
Modified to add cart, baffle and grille
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL
IMPORTANT: SAVE THESE INSTRUCTIONS
FIRE HAZARD. Do not use as a residential or
household heater. Keep combustible material away
from heater. Do not operate heater where flamma-
ble vapors, gases or liquids are present.
To avoid personal injury read “IMPORTANT
INSTRUCTIONS” on this page before installation or
operation of heater.
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should
always be followed to reduce risk of fire, electric shock and injury
to persons, including the following:
7. This heater has hot surfaces. Do not use it in areas where gaso-
line, paint or flammable liquids are used or stored.
8. Use this heater only as described in this manual. Any other use
not recommended by the manufacturer may cause fire, electric
shock or injury to persons.
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not let bare
skin touch hot surfaces. Keep combustible materials, such as
furniture and papers at least 7 feet from the front of the heater.
3. Do not leave heater unattended while in operation.
4. Always disconnect heater when not in use.
5. Do not use outdoors in areas subject to wind.
6. Connect to properly grounded outlets or building ground.
9. In order to prevent equipment damage, protect with a ground
fault device such as Chromalox STAR-TG series monitor.
10. These instructions amend the fixed instructions that came
with the original heater.
SAVE THESE INSTRUCTIONS
WIRING
Use type “SO” or equal power cord. Refer to table 1 for proper wire gage and number of conductors.
Table 1
Amperage
Cord Ga./No. cond.
Model
Volts
KW
1 Phase
3 Phase
1 Phase
3 Phase
STAR-05-81-P
STAR-05-21-P
STAR-05-71-P
STAR-05-41-P
STAR-05-61-P
208
240
277
480
600
4.5
4.5
4.5
4.5
4.5
21.6
18.8
16.2
9.4
NA
NA
NA
NA
NA
12/3
12/3
14/3
14/3
14/3
NA
NA
NA
NA
NA
7.5
STAR-06-83-P
STAR-06-23-P
STAR-06-71-P
STAR-06-43-P
STAR-06-63-P
208
240
277
480
600
6
6
6
6
6
28.8
25.0
21.7
12.5
10.0
16.7
14.4
—
10/3
10/3
10/3
12/3
12/3
12/4
12/4
—
12/4
12/4
7.2
5.8
STAR-14-83-P
STAR-14-23-P
STAR-14-71-P
STAR-14-43-P
STAR-14-63-P
208
240
277
480
600
13.5
13.5
13.2
13.5
13.5
NR
NR
47.7
28.1
22.5
37.5
32.5
—
16.2
13.0
NR
NR
6/4
8/4
6/3
—
10/3
10/3
12/4
12/4
NA - Not Available
NR - Not Recommended
RENEWAL PARTS IDENTIFICATION
Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333-557518-001
End Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 039-510848-001
Vinyl Grip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 024-304894-001
Grill for STAR-06. . . . . . . . . . . . . . . . . . . . . . . 143-304892-001
Grills for STAR-14 (2) . . . . . . . . . . . . . . . . . . . 134-304892-003
Hardware for Mounting Grills GR14TW
Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248-075512-123
Square Nut . . . . . . . . . . . . . . . . . . . . . . . . . 200-048688-007
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty:
Please refer to the Chromalox limited warranty applicable to this product at
2150 N. RULON WHITE BLVD., OGDEN, UT 84404
Phone: 1-800-368-2493
Download from Www.Somanuals.com. All Manuals Search And Download.
|