38-VIV206-01
MODEL
✽✽Projection lens is optional.
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPLIANCES
Federal Communication Commission Notice
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures :
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number
Trade Name
Responsible party
Address
: 38-VIV206-01
: Christie
: CHRISTIE DIGITAL SYSTEMS, Inc.
: 10550 Camden Drive Cypress, CA 90630 USA
: (714) 236-8610
Telephone No.
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be
unable to insert the plug into the outlet, contact your electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FEATURES AND DESIGN
6
7
COMPUTER MODE
22
SELECTING INPUT SOURCE
SELECTING COMPUTER SYSTEM
22
22
23
23
24
26
PREPARATION
PC ADJUSTMENT
AUTO PC ADJUSTMENT
MANUAL PC ADJUSTMENT
COMPATIBLE COMPUTER SPECIFICATIONS
NAME OF EACH PART OF PROJECTOR
7
8
8
9
9
9
10
10
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
LENS INSTALLATION
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT
27
27
28
IMAGE LEVEL ADJUSTMENT
POSITIONING PROJECTOR
LENS SHIFT ADJUSTMENT
ADJUSTABLE FEET
PICTURE SCREEN ADJUSTMENT
29
MOVING PROJECTOR
VIDEO MODE
30
CONNECTING PROJECTOR
11
SELECTING INPUT SOURCE
SELECTING VIDEO SYSTEM
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT
30
31
32
32
33
TERMINALS OF PROJECTOR
CONNECTING TO COMPUTER
CONNECTING TO VIDEO EQUIPMENT
11
12
13
IMAGE LEVEL ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
34
BEFORE OPERATION
14
SETTING
35
OPERATION OF REMOTE CONTROL
LASER POINTER FUNCTION
14
14
15
SETTING MENU
35
REMOTE CONTROL BATTERIES INSTALLATION
TOP CONTROL PANEL AND INDICATORS
16
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
MENU BAR
17
17
17
18
APPENDIX
37
OPERATING WIRELESS MOUSE
37
MAINTENANCE
38
38
38
38
39
39
WARNING TEMP. INDICATOR
AIR FILTER CARE AND CLEANING
CLEANING PROJECTION LENS
LAMP REPLACEMENT
BASIC OPERATION
19
TURNING ON / OFF PROJECTOR
19
LAMP REPLACE COUNTER
ADJUSTING SCREEN
ZOOM ADJUSTMENT
20
20
20
20
20
21
21
21
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
40
42
FOCUS ADJUSTMENT
LENS SHIFT ADJUSTMENT
KEYSTONE ADJUSTMENT
PICTURE FREEZE FUNCTION
NO SHOW FUNCTION
P-TIMER FUNCTION
SOUND ADJUSTMENT
21
TRADEMARKS
✽ Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
✽ IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
✽ Windows and PowerPoint are registered trademarks of Microsoft Corporation.
✽ Each name of corporations or products in the user's manual is a trademark or a registered trademark of its
respective corporation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AND DESIGN
This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)
technology.
✽ Compact Design
✽ Digital Zoom (for Computer)
This projector is extremely compact in size and weight.
It is designed to carry and work anywhere.
The Digital Zoom function adjusts the image size to
approx. 1/4 ~ 49 times of original image size, allowing
you to focus on crucial information at a presentation.
✽ Compatibility
✽ Keystone Correction
This projector accepts various video and computer input
signals including;
Positioning of a projector may result in distorted image
being displayed in a trapezoid shape. Keystone
Correction solves this problem by digitally altering
projection to produce undistorted images.
✽ Computers
IBM-compatible or Macintosh computer up to 1280
x 1024 resolution.
✽ 6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-
N color system can be connected.
✽ Power Management
Power Management function is provided to reduce power
consumption while the projector is not in use.
✽ Component Video
Component video signal, such as from a DVD
player, high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i or 1080i, can be
connected.
This Power Management function operates to turn the
Projection Lamp off when the projector detects signal
interruption and any button is not pressed within 5
minutes. The Projection Lamp is automatically turned on
again when the projector detects signal or any operation
button is pressed.
✽ S-Video
S-Video signal, such as a S-VHS VCR output
signal, can be connected.
This projector is shipped with this function ON.
✽ High Resolution Image
✽ Digital Visual Interface
This projector provides 1024 x 768 dots resolution for
computer input and 800 horizontal TV lines. Resolution
from a computer between XGA (1024 x 768) and SXGA
(1280 x 1024) is compressed into 1024 x 768 dots. This
projector can not display images over 1280 x 1024 dots.
When resolution of your computer is more than 1280 x
1024, reset a computer output for lower resolution.
This projector is equipped with DVI 24-pin terminal for
connecting DVI output from a computer.
✽ Laser Pointer Function
The Remote Control Unit supplied with this projector
includes a Laser Pointer function. This function helps you
to make a smart presentation on a projected screen.
✽ Multi-Scan System
This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for troublesome manual adjustment of frequency
and other settings.
✽ Wireless Mouse
The Remote Control Unit supplied with this projector has
a Wireless Mouse function for a connected computer.
This function enables you to operate both the projector
and computer only with the Remote Control Unit.
✽ One-Touch Auto PC Adjustment
Incoming computer video signals are recognized and the
best adjustment is automatically set by Auto PC
Adjustment. No complicated setup is necessary and
projection is always precise.
✽ Multilanguage Menu Display
The Operation menu is displayed in: English, German,
French, Italian, Spanish, Portuguese, Dutch, Swedish,
Chinese, Korean or Japanese.
✽ Motor-driven Lens Shift
✽ ChristieNet (Optional)
The projection lens can be moved up and down with the
motor-driven lens shift function. This function makes it
easy to project the image where you wish.
Zoom and focus can be also adjusted with motor-driven
operation.
ChristieNet is an optional product to control and set up a
projector via the network cable. By accessing to the
connected projector using the web browser on your
computer. It can be controlled and set up the projector
remotely. Contact the sales dealer where you purchased
this projector for optional parts.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
NAME OF EACH PART OF PROJECTOR
FRONT OF CABINET
TOP CONTROL PANEL
AND INDICATORS
PROJECTION LENS
AIR INTAKE
VENT
INFRARED
REMOTE RECEIVER
LENS COVER
SPEAKERS
BACK OF CABINET
EXHAUST VENT
TERMINALS
AND CONNECTORS
INFRARED
REMOTE RECEIVER
POWER CORD
CONNECTOR
HOT AIR EXHAUSTED !
Air blown from exhaust vent is hot. When
using or installing a projector, following
precautions should be taken.
✽ Do not put a flammable object near this vent.
✽ Keep rear grills at least 3’(1 m) away from
any object, especially heat-sensitive object.
✽ Do not touch this area, especially screws
and metallic parts. This area will become
hot while a projector is used.
CARRYING
HANDLE
This projector detects internal temperature
and automatically controls operating power
of Cooling Fans.
LAMP COVER
When attaching the ChristieNet (optional part)
to the projector, remove the these parts.
Refer to the owner's manual in the optional
ChristieNet.
BOTTOM OF CABINET
AIR INTAKE VENTS
This projector is equipped with cooling fans for protection from
overheating. Pay attention to following to ensure proper ventilation
and avoid a possible risk of fire and malfunction.
✽ Do not cover vent slots.
✽ Keep side clear of any objects. Obstructions may block cooling
air.
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
This projector uses nominal input voltages of 100-120 V or 200-240
V AC. This projector automatically selects the correct input
voltage. It is designed to work with single-phase power systems
having a grounded neutral conductor. To reduce risk of electrical
shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of the type of power supply used.
Connect the projector with peripheral equipment before turning the
projector on. (Refer to pages 11 ~ 13 for connection.)
CAUTION
For safety, unplug AC Power Cord when an appliance is not
used.
When this projector is connected to the outlet with an AC Power
Cord, the appliance is in Stand-by Mode and consumes a little
electric power.
Connect the AC Power Cord (supplied) to the
projector.
The AC outlet must be near this equipment and must
be easily accessible.
CAUTION
The AC Power Cord must meet the requirement of the country where you use the projector.
Confirm the AC plug type with the chart below. The proper AC Power Cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
Projector side
AC Outlet side
For U.S.A. and Canada
For Continental Europe
Ground
To POWER CORD
CONNECTOR on the
projector.
To AC Outlet.
(120 V AC)
To AC Outlet.
(200 - 240 V AC)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
LENS INSTALLATION
Before setting up a projector, install Projection Lens on
Projector.
1. Before installation, check where a projector is used and
prepare a suitable lens. For specifications of a Projection
Lens, contact sales dealer where you purchased a projector.
2. For installation, refer to installation manual in the optional
lens.
NOTE;
COVER CAP
When installing the lens, remove the cover cap in the
projector.
POSITIONING PROJECTOR
This projector is designed to project on a flat projection
surface.
SCREEN
ROOM LIGHT
Brightness in a room has a great influence on picture
quality. It is recommended to limit ambient lighting in
order to provide best image.
LENS SHIFT ADJUSTMENT
Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to
provide projected image where you want. U/D ratio can be adjusted 10 : 0 ~ 1 : 1 (refer to figure below.). Refer
to P 20 for operation.
Highest (10 : 0)
Lowest (1 : 1)
1
1
10 : 0
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by
rotating ADJUSTABLE FEET. Projection angle can be
adjusted to 10.5 degrees.
Lift front of a projector and pull FEET LOCK LATCHES
on both sides of a projector.
1
Release FEET LOCK LATCHES to lock ADJUSTABLE
FEET and rotate ADJUSTABLE FEET to fine tune
position and tilt.
2
To shorten ADJUSTABLE FEET, lift front of a projector
and pull and undo FEET LOCK LATCHES.
3
Position and keystone distortion of image can be adjusted
using Menu Operation. (Refer to P 20 and 35.)
ADJUSTABLE FEET
FEET LOCK
LATCHES
NOTE :
THIS PROJECTOR SHOULD BE SET IN THE WAY
INDICATED. PROJECTION LAMP MAY MALFUNCTION.
MOVING PROJECTOR
Use Carry Handle when moving a Projector.
When moving a projector, replace lens cover and retract
feet to prevent damage to lens and cabinet.
When this projector is not in use for an extended period,
put it into case (dust cover) supplied with this projector.
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR
✽ Do not drop or bump a projector, otherwise damages or malfunctioning may result.
✽ When carrying a projector, use a suitable carrying case.
✽ Do not transport a projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to a projector. To transport a projector through a courier or transport service, consult
your dealer for the best method.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on
pages 11 to 13 and connect properly.
COMPUTER INPUT
TERMINALS (DIGITAL/ANALOG)
COMPUTER AUDIO
INPUT (1 and 2) JACKS
Connect the computer (digital/analog)
output to one of these terminals.
(Refer to P12.)
Connect the audio output
(stereo) from the computer
to these jacks.
R/C JACK
When using the Wired/Wireless
Remote Control Unit as a Wired
Remote Control, connect the
Wired Remote Control Unit to
this jack with the Remote
Control Cable (supplied).
(Refer to P12.)
INPUT 1
USB CONNECTOR (Series B)
ANALOG
DIGITAL(DVI-D)
R/C JACK
When controlling the computer
with the Remote Control Unit of
the projector, connect the USB
port of your personal computer
to this terminal. (Refer to P12.)
CONTROL PORT
RESET
USB
AUDIO 1
AUDIO 2
CONTROL PORT CONNECTOR
G
B
R
H/V
V
When controlling the computer
with the Remote Control Unit
of the projector, connect the
mouse port of your personal
computer to this connector.
(Refer to P12.)
VIDEO/Y Cb/Pb
Cr/Pr
INPUT 2
RESET BUTTON
S–VIDEO
VIDEO/Y Cb/Pb Cr/Pr
R–AUDIO–L
This projector uses a micro processor
to control this unit, and occasionally
this micro processor may malfunction
and need to be reset. This can be
done by pressing the RESET button
with a pen, which will shut down and
restart unit. Do not use the RESET
function excessively.
(
)
MONO
INPUT 3
✽ Do not press this button. This button
is used for our optional accessories.
VIDEO INPUT JACKS
AUDIO INPUT JACKS
S-VIDEO INPUT JACK
Connect the composite video Connect the audio output Connect the S-VIDEO
output from video equipment to from video equipment to output from video
5 BNC INPUT JACKS
the VIDEO/Y jack or connect these jacks.
the component video outputs to (Refer to P13.)
the VIDEO/Y, Cb/Pb and Cr/Pr When the audio output is
equipment to this
jack. (Refer to P13.)
Connect the component video
output (Y, Cb, Cr or Y, Pb, Pr)
from video equipment to
VIDEO/Y, Cb/Pb and Cr/Pr
jacks or connect computer
output {5 BNC Type (Green,
Blue, Red, Horiz. Sync and
Vert. Sync.)} from computer
to G, B, R, H/V and V jacks.
(Refer to P12 and 13.)
jacks. (Refer to P13.)
monaural, connect it to
the L (MONO) jack.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
CONNECTING TO COMPUTER
Cables used for connection (✽ = Cable or adapter is not supplied with this projector.)
• VGA Cable (HDB 15 pin)
• USB Cable ✽
• DVI-Digital Cable (for Single Link T.M.D.S.) ✽
• BNC Cable ✽
• MAC Adapter (When connecting to Macintosh computer)
• Audio Cables (RCA x 2 and Mini Plug (stereo) x 1) ✽
• Control Cable for PS/2 Port, Serial Port or ADB Port
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
Desktop type
Laptop type
Monitor Output
Monitor Output
USB port Audio Output Serial port PS/2 port
ADB port
Control Cable
for Serial Port
Control Cable
for PS/2 Port
Control Cable
for ADB Port
USB
Cable ✽
MAC Adapter
Audio
Cable ✽
(stereo)
Set slide switches
according to chart
below.
Terminal
Terminal
DVI
Cable ✽
Terminal
BNC
Cable ✽
VGA Cable
Use one of these Control
Cables corresponding with
terminal of your computer.
COMPUTER
AUDIO IN 1 or 2
USB
COMPUTER IN ANALOG
CONTROL
PORT
COMPUTER IN DIGITAL
INPUT 1
ANALOG
DIGITAL(DVI-D)
R/C JACK
CONTRL PORT
RESET
USB
AUDO
1
AUDO
2
G
B
R
H/V
V
VIDEO/Y Cb/Pb
Cr/Pr
INPUT 2
S–VIDEO
VIDEO/Y Cb/Pb Cr/Pr
R–AUDIO–L
(
)
MONO
INPUT 3
Terminals
of the Projector
✽ MAC ADAPTER
NOTE :
When connecting the cable, the Power
Cords of both the projector and the external
equipment should be disconnected from the
AC outlet. Turn the projector and peripheral
equipment on before the computer is
switched on.
Set switches as shown in table
below depending on RESOLU-
TION MODE that you want to use
before you turn on projector and
computer.
ON
ON
DIP
1
2
3
4
5
6
OFF
3
1
2
4
5
6
13" MODE (640 x 480)
ON
ON OFF OFF OFF OFF
16" MODE (832 x 624) OFF ON OFF ON OFF OFF
19" MODE (1024 x 768) OFF ON
21" MODE (1152 x 870) ON ON
ON OFF OFF OFF
ON ON OFF OFF
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
Cables used for connection (✽ = Cable is not supplied with this projector.)
• Video Cable (RCA x 1 or RCA x 3) ✽
• BNC Cable ✽
• S-VIDEO Cable ✽
• Audio Cable (RCA x 2) ✽
Video Source (example)
Component video output equipment.
(such as DVD player or high-definition TV source.)
Video Cassette Recorder
Video Disc Player
Composite Component Video Output
Composite Component Video Output Audio Output
Video Output
(Y, Cb/Pb, Cr/Pr)
S-VIDEO Output
Video Output
(Y, Cb/Pb, Cr/Pr)
Video Cables
(RCA x 1 or
RCA x 3) ✽
Audio Cable
(RCA x 2) ✽
S-VIDEO
Cable ✽
BNC Cable ✽
VIDEO
Y - Cb/Pb - Cr/Pr VIDEO
Y - Cb/Pb - Cr/Pr AUDIO IN
S-VIDEO
INPUT 1
ANALOG
DIGITAL(DVI-D)
R/C JACK
CONTROL PORT
RESET
USB
AUDIO 1
AUDIO 2
G
B
R
H/V
V
VIDEO/Y Cb/Pb
Cr/Pr
INPUT 2
S–VIDEO
VIDEO/Y Cb/Pb Cr/Pr
R–AUDIO–L
(
)
MONO
INPUT 3
Terminals
of the Projector
NOTE :
When connecting the cable, the Power Cords of
both the projector and the external equipment
should be disconnected from the AC outlet.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATION OF REMOTE CONTROL
Left Side
LASER POINTER INDICATOR
POWER ON-OFF BUTTON
Used to turn projector on or
off. (P19)
Lights red while laser beam
is emitted from Laser Light
Window.
ON-OFF
ZOOM FOCUS
VOLUME
INPUT BUTTON
Used to select input source.
(P22)
D.ZOOM
MUTE
MENU
INPUT
MENU BUTTON
POINT BUTTON
Used to select MENU
operation. (P17, 18)
Used to move a pointer on ON-
SCREEN MENU, adjust each
item, or pan image in DIGITAL
ZOOM +/– mode. (P29)
It is also used as a PC mouse
in Wireless Mouse Operation.
(P37)
SELECT BUTTON
Used to execute item
selected, or to expand
or compress image in
DIGITAL ZOOM +/–
mode. (P29)
It is also used as a PC
mouse in Wireless
Mouse Operation. (P37)
✽ When pressing center of this
button, it works as SELECT
button.
ALL-OFF SWITCH
LASER
When using Remote Control Unit,
turn this switch to “ON.” And turn it
to “ALL OFF” when it is not used.
KEYSTONE
NO SHOW
RIGHT CLICK BUTTON
LENS SHIFT
Used as a PC mouse in
Wireless Mouse Operation.
(P37)
FREEZE
LASER BUTTON
AUTO PC ADJ.
P-TIMER
IMAGE
Used to operate Laser Pointer
Function. Laser beam is
emitted while pressing this
button within 1 minute.
When using this Laser Pointer
for more than 1 minute, release
LASER button and press it
again.
P-TIMER BUTTON
Used to operate P-TIMER
function. (P21)
LASER POINTER FUNCTION
This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is
pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released,
light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being
emitted.
Laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other
people. Three marks bellow are caution labels for laser beam.
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result
hazardous radiation exposure.
These caution labels are put on remote control.
LASER POINTER INDICATOR
Laser Light Window
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
Operating Range
ON-OFF
Point Remote Control Unit toward
projector (Receiver Window)
whenever pressing any button.
Maximum operating range for
Remote Control Unit is about 16.4’
(5m) and 60° in front and rear of a
projector.
ZOOM BUTTON
Used to adjust zoom.
(P20)
VOLUME BUTTON
Used to adjust volume.
(P21)
ZOOM FOCUS
VOLUME
FOCUS BUTTON
Used to adjust focus.
(P20)
D.ZOOM
MUTE
MENU
INPUT
D.ZOOM BUTTON
Used to select DIGITAL
ZOOM +/– mode and
resize image. (P29)
MUTE BUTTON
60°
Used to mute sound.(P21)
KEYSTONE BUTTON
Used to correct
keystone distortion.
(P20, 35)
16.4’
(5 m)
LASER
KEYSTONE
NO SHOW
FREEZE BUTTON
Used to freeze picture.
(P21)
NO SHOW BUTTON
Used to turn picture off.
(P21)
LENS SHIFT
FREEZE
IMAGE BUTTON
Used to select image
level. (P27, 32)
AUTO PC ADJ.
P-TIMER
IMAGE
AUTO PC ADJ. BUTTON
Use to operate AUTO PC
Adjustment function. (P23)
16.4’
(5 m)
LENS SHIFT BUTTON
Used to select LENS
SHIFT function. (P20)
WIRED REMOTE JACK
60°
When using as Wired
Remote Control, connect
Remote Control Cable to
this jack.
Battery installation is
required when using as
Wired Remote Control.
Remote Control Batteries Installation
Remove battery
compartment lid.
Slide batteries into
compartment.
Replace compartment lid.
1
2
3
Two AA size batteries
Press lid down-
ward and slide it.
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
To insure safe operation, please observe following precautions :
✽ Use (2) AA, UM3 or R06 type alkaline batteries.
✽ Replace two batteries at same time.
✽ Do not use a new battery with an used battery.
✽ Avoid contact with water or liquid.
✽ Do not expose Remote Control Unit to moisture, or heat.
✽ Do not drop Remote Control Unit.
✽ If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.
✽ Danger of explosion if battery is incorrectly replaced.
✽ Dispose of used batteries according to batteries manufacturers instructions and local rules.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
TOP CONTROL PANEL AND INDICATORS
This projector has CONTROL BUTTONS (TOP CONTROL PANEL) and INDICATORS on its top.
LAMP REPLACE INDICATOR
WARNING TEMP. INDICATOR
READY INDICATOR
LAMP INDICATOR
Turns yellow when the
life of the projection
lamp draws to an end.
(P39)
Flashes red when
Lights green when the
projector is ready to be
Becomes dim when the
projector is turned on.
And bright when the
projector is in stand-by
mode.
internal
projector
temperature is too
high. (P38)
turned on.
And it
flashes green in Power
Management mode.
(P36)
POWER ON–OFF BUTTON
Used to turn the projector
on or off. (P19)
MENU BUTTON
Used to open or close
MENU operation. (P17,
18)
INPUT BUTTON
Used to select the input
source. (P22, 30)
ZOOM BUTTON
Used to adjust zoom.
(P20)
FOCUS BUTTON
Used to adjust focus.
(P20)
AUTO PC ADJ. BUTTON
LENS SHIFT BUTTON
Used to operate AUTO PC
Adjustment function. (P23)
Used to select LENS
SHIFT function. (P20)
IMAGE BUTTON
Used to select image
level. (P27, 32)
SELECT BUTTON
POINT (VOLUME + / – ) BUTTONS
Used to execute the item
selected. It is also used
to expand/compress the
image in DIGITAL ZOOM
mode. (P29)
Used to select an item or adjust
value in ON-SCREEN MENU. They
are also used to pan the image in
DIGITAL ZOOM +/– mode. (P29)
POINT LEFT/RIGHT buttons are
also used as VOLUME +/– buttons.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
WIRELESS REMOTE CONTROL
You can control and adjust this projector through the ON-SCREEN
MENU. Refer to the following pages to operate each adjustment
on the ON-SCREEN MENU.
POINT BUTTON
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
1 DISPLAY MENU
Press MENU button to display ON-SCREEN MENU.
2 MOVING POINTER
SELECT BUTTON
Used to select item.
Move the pointer (✽ see below) or adjust the value of the item by
pressing POINT button(s) on Top control panel or on Remote
Control Unit.
✽ Pointer is the icon on ON-SCREEN MENU to select the item.
See the figures on the section "FLOW OF ON-SCREEN MENU
OPERATION" below.
TOP CONTROL PANEL
POINT BUTTONS
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
3 SELECT ITEM
Select the item or set selected function by pressing SELECT
button.
SELECT BUTTON
Used to select the item.
FLOW OF ON-SCREEN MENU OPERATION
MENU BAR
MENU ICON
Display ON-SCREEN MENU
Press MENU button to display ON-SCREEN MENU (MENU
BAR). A red frame is POINTER.
1
POINTER
(red frame)
POINTER (red frame)
Select Menu to be adjusted
Press the POINT DOWN but-
ton to move POINTER.
Move POINTER (red frame) to MENU ICON that you want to
2
select by pressing the POINT RIGHT / LEFT buttons.
ITEM
Control or adjust item through ON-SCREEN MENU
Press the POINT DOWN button and move POINTER (red
frame or red arrow) to ITEM that you want to adjust, and then
press SELECT button to show ITEM DATA.
3
SELECT
BUTTON
Adjust ITEM DATA by pressing the POINT RIGHT / LEFT
buttons.
Refer to the following pages for details of respective
adjustments.
4
ITEM DATA
Press the POINT LEFT/RIGHT
buttons to adjust value or set
function.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
MENU BAR
FOR PC SOURCE
Press MENU BUTTON while connecting to PC input source.
IMAGE SELECT MENU
SCREEN MENU
SETTING MENU
Used to select
Used to adjust size
of image. [Normal
/True/Wide/Digital
zoom +/–]
Used to change
settings of projector
or reset Lamp
Replace Counter.
(Refer to P35-37)
GUIDE WINDOW
PC SYSTEM MENU
image level among
Standard, Real
and Image 1 ~ 4.
(Refer to P27)
Shows selected
item of ON-
SCREEN MENU.
Used to select
computer system.
(Refer to P22, 23)
(Refer to P29)
INPUT MENU
PC ADJUST MENU
IMAGE ADJUST MENU
SOUND MENU
Used to select
Used to adjust
parameters to
match with input
signal format.
Used to adjust
Used to adjust
volume or mute
sound.
input source (Input
1, Input 2 or Input
3). (Refer to P22)
computer image.
[Contrast/Brightness/
White Balance
(Refer to P21)
(Refer to P23-25)
(R/G/B)/Gamma]
(Refer to P28)
FOR VIDEO SOURCE
Press MENU BUTTON while connecting to VIDEO input source.
INPUT MENU
Used to select
input source
(Input 1, Input 2
or Input 3).
IMAGE SELECT MENU
SCREEN MENU
Used to select image
level among
Standard, Cinema
and Image 1 ~ 4.
(Refer to P32)
Used to set size of
image to Normal
or Wide.
(Refer to P30)
(Refer to P34)
AV SYSTEM MENU
IMAGE ADJUST MENU
Same function as
Menu for PC source.
Same function as
Menu for PC source.
Used to select
system of selected
video source.
Used to adjust picture image.
[Contrast/Brightness/Color/Tint/
White balance (R/G/B)/
(Refer to P31)
Sharpness/Gamma/Noise
Reduction/Progressive]
(Refer to P33, 34)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
TURNING ON / OFF PROJECTOR
TURNING ON PROJECTOR
Complete peripheral connections (with Computer, VCR, etc.)
before turning on projector. (Refer to "CONNECTING TO
PROJECTOR" on pages 11~13 for connecting that equipment.)
Input position and
Lamp mode status
1
2
Input 1
Connect a projector's AC Power Cord into an AC outlet. LAMP
Indicator lights RED, and READY Indicator lights GREEN.
30
NOTE : When “On start” function is ON, this projector is turned
on automatically by connecting AC Power Cord to an
AC outlet. (Refer to pages 35, 36.)
Press POWER ON-OFF button on Top control panel or on
Remote Control Unit to ON. LAMP Indicator dims, and Cooling
Fans start to operate. Preparation Display appears on a screen
and count-down starts. Signal from PC or Video source appears
after 30 seconds.
3
Preparation Display disappears after 30 seconds.
Current Input position and Lamp mode status are also displayed
on screen for 5 seconds. (Refer to "LAMP MODE" on page 36.)
TURNING OFF PROJECTOR
Press POWER ON-OFF button on Top control panel or on
Remote Control Unit, and a message "Power off?" appears on a
screen.
1
2
Press POWER ON-OFF button again to turn off projector. LAMP
Indicator lights bright and READY Indicator turns off. After
projector is turned off, Cooling Fans operate (for 90 seconds).
During this "Cooling Down" period, this appliance can not be
turned on.
Power off?
Message disappears after 4 seconds.
When projector has cooled down, READY Indicator lights
GREEN again and you can turn projector on. After cooling down
completely, disconnect AC Power Cord.
3
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically.
Refer to “Power Management” on page 35.
When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on
projector again.
When WARNING TEMP. Indicator continues to flash, follow procedures below:
1. Press POWER ON-OFF button to turn a projector off and disconnect AC Power Cord from an AC outlet.
2. Check Air Filters for dust accumulation.
3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 38.)
4. Turn a projector on again.
If WARNING TEMP. Indicator should still continue to flash, contact sales dealer where you purchased this projector or
service center.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
ADJUSTING SCREEN
ZOOM ADJUSTMENT
Press ZOOM button on Top control panel or ZOOM ✽/✽ button
on Remote Control Unit. Message “Zoom” is displayed.
1
2
Press ZOOM ✽ button or the POINT UP button to make image
larger, and press ZOOM ✽ button or the POINT DOWN button
to make image smaller.
Zoom
Message disappears after 4 seconds.
FOCUS ADJUSTMENT
Press FOCUS button on Top control panel or FOCUS ✽/✽
button on Remote Control Unit. Message “Focus” is displayed.
1
2
Adjust focus of image by pressing FOCUS ✽/✽ button or the
POINT UP/DOWN button(s) .
Focus
NOTE;
Focus adjustment may not function properly if the image is
corrected by KEYSTONE adjustment.
Message disappears after 4 seconds.
LENS SHIFT ADJUSTMENT
Press LENS SHIFT button on Top control panel or LENS SHIFT
✽/✽ button on Remote Control Unit. Message “Lens shift” is
displayed.
1
2
Press the POINT UP button or LENS SHIFT ✽ button to move
image up, press the POINT DOWN or LENS SHIFT ✽ button to
move image down.
Lens shift
KEYSTONE ADJUSTMENT
If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.
Press KEYSTONE button on Remote Control Unit or select
Keystone on SETTING menu. (Refer to page 35.) Keystone
dialog box appears.
1
Correct keystone distortion by pressing the POINT
UP/DOWN/LEFT/RIGHT button(s). Press the POINT UP button
to reduce the upper part of the image, and press the POINT
DOWN button to reduce the lower part. Press the POINT LEFT
button to reduce the left part, and press the POINT RIGHT
button to reduce the right part.
2
• Arrows are white in no correction.
• Arrow(s) of direction being corrected turn(s) red.
• Arrow(s) disappear(s) at the maximum
correction.
Reduce the lower width with
the POINT DOWN button.
Reduce the upper width
with the POINT UP button.
Reduce the left part with
the POINT LEFT button.
Reduce the right part with
the POINT RIGHT button.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
PICTURE FREEZE FUNCTION
Press FREEZE button on Remote Control Unit to freeze the picture on-screen. To cancel FREEZE function, press FREEZE
button again or press any other button except the POINT, SELECT, RIGHT CLICK and LASER buttons.
NO SHOW FUNCTION
Press NO SHOW button on Remote Control Unit to black out the
No show
image. To restore to normal, press NO SHOW button again or press
any other button except the POINT, SELECT, RIGHT CLICK and
LASER buttons.
The message disappears after 4 seconds.
P-TIMER FUNCTION
Press P-TIMER button on Remote Control unit. The timer display “00 :
00” appears on the screen and the timer starts to count time (00 : 00 ~
59 : 59).
To stop P-TIMER display, press P-TIMER button. And then, press P-
TIMER button again to cancel P-TIMER function.
SOUND ADJUSTMENT
Indicates roughly level of
volume.
DIRECT OPERATION
Volume
Press VOLUME (+/–) button(s) on Top control panel or on Remote
Control Unit to adjust volume. Volume dialog box appears on screen
for a few seconds.
(+) button to increase volume, and (–) button to decrease.
Mute
Press the MUTE button on Remote Control Unit to disable sound. To
restore sound to its previous level, press MUTE button again or press
Volume (+/–) button(s).
Press the MUTE button to set
Mute function On or Off.
Display disappears after 4 seconds.
MENU OPERATION
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT buttons to move the red frame pointer
to the SOUND Menu icon.
1
SOUND MENU
Press the POINT DOWN button to move the red frame pointer to
the item that you want to select, and then press SELECT button.
2
SOUND Menu icon
Volume
Indicates roughly
level of volume.
To increase volume, press the POINT RIGHT button, and press the
POINT LEFT button for decreasing.
Close SOUND Menu.
Mute
Press the POINT LEFT/RIGHT button(s) to disable sound. The dialog
box display will change to “On” and the sound will be disabled. To
restore sound to its previous level, press the POINT LEFT/RIGHT
button(s) again.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
SELECTING INPUT SOURCE
INPUT button
Input 1
DIRECT OPERATION
Select the appropriate input signal by pressing the INPUT button on
the Top control panel or on the Remote Control Unit.
If projector cannot reproduce proper image, select correct input source
through MENU OPERATION (see below).
Input 2
Input 3
MENU OPERATION
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT buttons to select Input and press
1
SELECT button.
appear.
Menu will
Another dialog box INPUT SELECT
INPUT Menu icon
Press the POINT DOWN button and a red-arrow icon will
appear. Move arrow to INPUT source that you want to select,
and then press SELECT button.
2
SELECTING COMPUTER SYSTEM
WHEN SELECTING INPUT 1 (COMPUTER INPUT TERMINALS )
INPUT MENU
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT button to move the red frame pointer to
INPUT Menu icon.
1
2
3
INPUT Menu icon
Press the POINT DOWN button to move the red arrow pointer to
Input 1 and then press SELECT button. Source Select Menu will
appear.
Move the pointer (red arrow)
to Input 1 and press SELECT
button.
Move the pointer to either Digital or Analog and then press
SELECT button.
Input 1
Source Select Menu
When your computer is connected to COMPUTER
INPUT (DIGITAL) terminal, select RGB (Digital).
Move the pointer to Digital or
Analog and press SELECT
button.
Digital
When your computer is connected to COMPUTER INPUT
(ANALOG) terminal, select RGB (Analog).
Analog
WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )
When connecting a computer output [5 BNC Type (Green, Blue, Red,
Horiz. Sync and Vert. Sync.)] from a computer to G, B, R, H/HV and V
jacks.
INPUT MENU
INPUT Menu icon
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT button to move the red frame pointer to
INPUT Menu icon.
1
Move the pointer (red arrow)
to Input 2 and press SELECT
button.
Press the POINT DOWN button to move the red arrow pointer to
Input 2 and then press SELECT button. Source Select Menu will
appear.
Input 2
2
Source Select Menu
Press the POINT DOWN button and a red-arrow icon will
appear. Move arrow to "RGB", and then press SELECT button.
Move the pointer to RGB
and press SELECT button.
3
22
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
AUTOMATIC MULTI-SCAN SYSTEM
This projector automatically detects different types of computer resolutions such as VGA, SVGA, XGA or SXGA (refer to
“COMPATIBLE COMPUTER SPECIFICATIONS” on page 26). When selecting Computer, this projector automatically
detects incoming signal and projects proper image without any special setting. (Some computers need setting manually.)
Note : Projector may display one of following messages.
When projector can not recognize connected signal as
PC system provided in this projector, Auto PC Adjustment
function operates to adjust projector and the message
“Auto” is displayed on SYSTEM Menu icon.
PC SYSTEM MENU
Auto
When image is not provided properly, manual adjustment
is required. (Refer to P24 and 25.)
PC SYSTEM Menu icon
Displays system being
selected.
There is no signal input from computer. Make sure
connection of computer and the projector is set correctly.
(Refer to TROUBLESHOOTING on page 40.)
––––
D-VGA, D-SVGA or D-XGA
When digital computer signal is received on DVI terminal,
above message is displayed on PC SYSTEM Menu icon.
PC SYSTEM MENU
SELECT COMPUTER SYSTEM MANUALLY
This projector automatically selects PC system among those provided
in this projector and PC system can be also selected manually.
PC SYSTEM Menu icon
Displays system being selected.
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT buttons to move the red frame pointer
to PC SYSTEM Menu icon.
1
Systems on this dialog box can
be selected.
Press the POINT DOWN button to move the red arrow pointer to
Custom Mode (1~5) set in PC
ADJUST Menu. (P24, 25)
2
the system that you want to set, and then press
SELECT button.
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your
computer. Auto PC Adjustment function can be operated as follows.
Auto PC Adj.
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT button to move the red frame pointer to
PC ADJUST Menu icon.
PC ADJUST MENU
1
2
Press the POINT DOWN button to move the red frame pointer to
AUTO PC Adj. icon and then press SELECT button twice.
This Auto PC Adjustment can be also executed by pressing
AUTO PC ADJ. button on the Top control panel or on the
Remote Control Unit.
PC ADJUST Menu icon
Move the red frame pointer to AUTO PC
Adj. icon and press SELECT button.
Store adjustment parameters.
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector. Once parameters are memorized, setting can be
done just by selecting Mode in PC SYSTEM Menu (P23). Refer to
step 3 of MANUAL PC ADJUSTMENT section (P25).
NOTE
✽ Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment
function. When the image is not provided properly through this function, manual adjustments are required. (Refer to page
24, 25.)
✽ Auto PC Adjustment function can not be operated in Digital Signal input on DVI terminal and when “RGB”, “720p (HDTV)”,
“1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically detect display signals from most personal computers currently distributed. However, some
computers employ special signal formats which are different from the standard ones and may not be detected by the Multi-
Scan system of this projector. If this happens, the projector can not reproduce a proper image and the image may be
recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special
signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This
enables you to recall the setting for a specific computer whenever you use it.
Note : This PC ADJUST Menu can not be operated when a digital signal is input to the DVI terminal or “RGB” is selected on
PC SYSTEM MENU (P23).
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT button to move the red frame pointer to
PC ADJUST Menu icon.
PC ADJUST MENU
1
2
Press the POINT DOWN button to move the red frame pointer to
the item that you want to adjust and then press SELECT button.
Adjustment dialog box will appear. Press the POINT
LEFT/RIGHT button to adjust value.
PC ADJUST Menu icon
Move the red frame icon to the item and
press SELECT button.
Fine sync
Adjusts an image as necessary to eliminate flicker from display.
Press the POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)
Shows status
(Stored / Free) of the
selected Mode.
Total dots
Selected Mode
The number of total dots in one horizontal period. Press the POINT
LEFT/RIGHT button(s) and adjust number to match your PC image.
Horizontal
Adjusts horizontal picture position. Press the POINT LEFT/RIGHT
button(s) to adjust position.
Press the POINT LEFT/RIGHT
button to adjust the value.
Vertical
Adjusts vertical picture position. Press the POINT LEFT/RIGHT
button(s) to adjust position.
Press SELECT button at this icon to
adjust “Clamp,” “Display area (H/V)” or
set “Full screen.”
Current mode
Press SELECT button to show information of computer selected.
Clamp
Current mode
Adjusts clamp position. When image has a dark bar(s), try this
adjustment.
Press SELECT button at
Current mode icon to show
information of computer
connected.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
Display area
Selects area displayed with this projector. Select the resolution in the
Display area dialog box.
Press SELECT button at
Display area icon and Display
area dialog box appears.
Display area H
Adjustment of horizontal area displayed with this projector. Press the
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Display area
Display area V
Adjustment of vertical area displayed with this projector. Press the
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Press the POINT LEFT
/RIGHT button(s) to
adjust value and then
press SELECT button.
Full screen
Press the POINT LEFT/RIGHT button(s) to switch Full screen
function to “On” or “Off.” Set “On” to resize image with 4 x 3 aspect
ratio to fit screen.
NOTE : Fine sync., Total dots, Display area (H/V) and Full screen
can not be adjusted when “1035i (HDTV)” or “1080i (HDTV)”
is selected on PC SYSTEM Menu (P23).
To store adjustment data.
This Mode has parameters being stored.
Store
3
To store adjustment parameters, move the red frame pointer to
Store icon and then press SELECT button. Move the red arrow
pointer to any of Mode 1 to 5 that you want to store and then
press SELECT button.
Mode free
To clear adjustment parameters previously set, move the red
frame pointer to Mode free icon and then SELECT button. Move
the red arrow pointer to Mode that you want to clear and then
press SELECT button.
Vacant Mode
Store icon
Shows values of “Total dots,”
“Horizontal,” “Vertical,” “Display
area H,” and “Display area V.”
Other icons operate as follows.
Reset
Reset all adjusted parameters on the adjustment dialog box to
previous settings.
To clear adjustment data.
Quit
Closes PC ADJUST MENU.
Close this dialog box.
Mode free icon
25
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
COMPATIBLE COMPUTER SPECIFICATIONS
This projector can accept a signal from all computers with V, H-Frequency mentioned below and less than 160
MHz of Dot Clock.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
VGA 3
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
RGB
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
15.734
15.625
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
56.47
60.31
48.50
44.00
63.48
36.00
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
30
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
XGA15
1024 x 768
1024 x 768
62.04
61.00
35.522
46.90
47.00
58.03
60.24
68.68
64.20
62.50
63.90
63.34
63.74
71.69
81.13
63.98
79.976
60.00
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
63.79
75.00
80.00
45.00
33.75
33.75
77.07
75.70
43.48
58.20
58.30
72.0
1024 x 768
(Interlace)
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 870
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1152 x 900
1152 x 900
MAC 19
MAC 21
SXGA 1
SXGA 2
SXGA 3
SXGA 4
SXGA 5
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
SXGA 13
SXGA 14
75.08
75.06
70.40
58.60
60.00
59.98
60.01
67.19
76.107
60.02
75.025
60.00
65.20
75.60
43.00
47.00
60.01
72.00
66.00
43.35
60.18
75.08
75.08
60.00
30.00
30.00
––––––––
(Interlace)
––––––––
(Interlace)
RGB
25
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
XGA 2
XGA 3
XGA 4
XGA 5
XGA 6
XGA 7
XGA 8
XGA 9
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
43.59
1280 x 1024
(Interlace)
1280 x 1024
(Interlace)
SXGA 15 1280 x 1024
SXGA 16 1280 x 1024
SXGA 17
SXGA 18
1152 x 900
1280 x 1024
(Interlace)
SXGA 19 1280 x 1024
MAC
MAC
720p (HDTV)
1035i (HDTV)
1080i (HDTV)
1280 x 960
1280 x 1024
––––––––
(Progressive)
––––––––
(Interlace)
1024 x 768
(Interlace)
––––––––
(Interlace)
When an input signal is digital from the DVI terminal, refer to chart below.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
D-VGA
640 x 480
800 x 600
31.469
37.879
59.940
60.317
D-XGA
1024 x 768
48.363
60.004
D-SVGA
NOTE : Specifications are subject to change without notice.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Real, Image 1, Image 2, Image 3
IMAGE button
and Image 4 by pressing IMAGE button on Top control panel or on
Remote Control Unit.
Standard
Real
Standard
Normal picture level preset on this projector.
Image 1
Image 2
Image 3
Image 4
Real
Picture level with improved halftone for graphics.
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P28).
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT button to move the red frame pointer to
IMAGE SELECT Menu icon.
IMAGE SELECT MENU
1
2
Press the POINT DOWN button to move the red frame pointer to
level that you want to set and then press SELECT button.
IMAGE SELECT
Menu icon
Standard
Normal picture level preset on this projector.
Move the red frame icon to level
and press SELECT button.
Real
Picture level with improved halftone for graphics.
IMAGE 1~4
Level being selected.
User preset picture adjustment in IMAGE ADJUST Menu (P28).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
IMAGE LEVEL ADJUSTMENT
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT buttons to move the red frame pointer
to IMAGE ADJUST Menu icon.
IMAGE ADJUST MENU
1
2
Press the POINT DOWN button to move the red frame pointer to
the item that you want to adjust and then press SELECT button.
The level of each item is displayed. Adjust each level by
pressing the POINT LEFT/RIGHT button(s).
IMAGE ADJUST
Menu icon
Move the red frame pointer to
the item to be selected and
then press SELECT button.
Contrast
Press the POINT LEFT button to decrease contrast, and the POINT
RIGHT button to increase contrast. (From 0 to 63.)
Brightness
Press the POINT LEFT button to decrease brightness, and the
POINT RIGHT button to increase brightness. (From 0 to 63.)
Selected Image level
White balance (Red)
Press the POINT LEFT button to lighten red tone and the POINT
RIGHT button to enhance red tone. (From 0 to 63.)
White balance (Green)
Press the POINT LEFT/RIGHT but-
tons to adjust value.
Press the POINT LEFT button to lighten green tone and the POINT
RIGHT button to enhance green tone. (From 0 to 63.)
White balance (Blue)
Press the POINT LEFT button to lighten blue tone and the POINT
RIGHT button to enhance blue tone. (From 0 to 63.)
Store icon
Press SELECT button at this icon to
store adjustment.
Gamma
Press either the POINT LEFT button or the POINT RIGHT button to
obtain better balance of contrast. (From 0 to 15.)
Store
3
To store manually preset image, move the red frame pointer to
Store icon and press SELECT button. Image Level Menu will
appear. Move the red frame pointer to Image 1 to 4 where you
want to set and then press SELECT button.
Image Level Menu
Other icons operate as follows.
Move the red frame pointer to
any of Image 1 to 4 where you
want to set and then press
SELECT button.
Reset
Reset all adjustment to previous settings.
Quit
Closes IMAGE MENU.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen adjustment function, which enables you to display the desirable image size.
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT button(s) to move the red frame pointer
to SCREEN Menu icon.
SCREEN MENU
1
2
Press the POINT DOWN button and move the red frame pointer
to the function that you want to select and then press SELECT
button.
SCREEN Menu icon
Move the red frame to the function and
press SELECT button.
Normal
Provides image to fit screen size.
True
Provides image in its original size. When original image size is larger
than screen size (1024 x 768), this projector enters “Digital zoom +”
mode automatically.
NOTE
✽ True and Digital zoom +/– can not be operated
when “RGB”, “1035i (HDTV)” or “1080i (HDTV)” is
selected on PC SYSTEM Menu (P23).
Wide
✽ Wide can not be selected when “720p (HDTV)”,
“1035i (HDTV)” or “1080i (HDTV)” is selected on
PC SYSTEM Menu (P23).
Provides image to fit wide video aspect ratio (16 : 9) by expanding
image width uniformly. This function can be used for providing a
squeezed video signal at 16 : 9.
✽ This projector can not display any resolution higher
than 1280 X 1024. If your computer’s screen
resolution is higher than 1280 X 1024, reset
resolution to lower before connecting projector.
Digital zoom +
When Digital zoom + is selected, ON-SCREEN MENU disappears
and the message “D. Zoom +” is displayed. Press SELECT button to
expand image size. And press the POINT UP/DOWN/LEFT/RIGHT
button(s) to pan the image. The panning function can work only when
the image is larger than the screen size.
A projected image can be also expanded by pressing D.ZOOM ✽
button on Remote Control Unit.
✽ Image data in other than XGA (1024 x 768) is
modified to fit screen size in initial mode.
✽ Panning function may not operate properly if
computer system prepared on PC ADJUST Menu
is used.
Digital Zoom –
When Digital zoom – is selected, ON-SCREEN MENU disappears
and the message “D. Zoom –” is displayed. Press SELECT button to
compress image size.
A projected image can be also compressed by pressing D.ZOOM ✽
button on Remote Control Unit.
To cancel Digital Zoom +/– mode, press any button except D.ZOOM
✽/✽, SELECT, POINT and AUTO PC ADJ. buttons.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
SELECTING INPUT SOURCE
WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )
When connecting to those equipment, select a type of Video
source in SOURCE SELECT Menu.
INPUT MENU
INPUT Menu icon
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT button to move the red frame pointer to
INPUT Menu icon.
1
Move the pointer (red arrow)
to Input 2 and press SELECT
button.
Press the POINT DOWN button to move the red arrow pointer to
Input 2 and then press SELECT button. Source Select Menu will
appear.
2
Input 2
Source Select Menu
Move the pointer to Video or
Y, Pb/Cb, Pr/Cr and press
SELECT button.
Move the pointer to source that you want to select and then
press SELECT button.
3
When video input signal is connected to VIDEO jack,
select Video.
Video
When video input signal is connected to Y-Pb/Cb-
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.
Y,Pb/Cb,Pr/Cr
WHEN SELECTING INPUT 3 (AV TERMINALS )
INPUT MENU
When connecting to those equipment, select a type of Video
source in SOURCE SELECT (VIDEO) Menu.
INPUT Menu icon
Press MENU button and ON-SCREEN MENU will appear. Press
1
the POINT LEFT/RIGHT button to move the red frame pointer to
INPUT Menu icon.
Move the pointer (red arrow)
to Input 3 and press SELECT
button.
Press the POINT DOWN button to move the red arrow pointer to
Input 3 and then press SELECT button. Source Select Menu will
appear.
2
Input 3
Source Select Menu (VIDEO)
Move the pointer to source
and press SELECT button.
Move the pointer to source that you want to select and then
press SELECT button.
3
When video input signal is connected to VIDEO jack,
select Video.
Video
When video input signal is connected to Y-Pb/Cb-
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.
Y,Pb/Cb,Pr/Cr
When video input signal is connected to S-VIDEO jack,
select S-Video.
S-Video
30
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
SELECTING VIDEO SYSTEM
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT buttons to move the red frame pointer
to AV SYSTEM Menu icon.
1
2
Press the POINT DOWN button to move the red arrow pointer to
system that you want to select and then press SELECT button.
VIDEO JACK OR S-VIDEO JACK
AV SYSTEM MENU (VIDEO OR S-VIDEO)
Auto
Projector automatically detects incoming Video system, and adjusts
itself to optimize its performance.
When Video System is PAL-M or PAL-N, select system manually first.
AV SYSTEM Menu icon
This box indicates system
being selected.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If projector can not reproduce proper video image, it is necessary to
select a specific broadcast signal format among PAL, SECAM, NTSC,
NTSC 4.43, PAL-M, and PAL-N.
Move the pointer to
system and press
SELECT button.
Y, Pb/Cb, Pr/Cr JACKS
AV SYSTEM MENU (COMPONENT VIDEO)
Auto
Projector automatically detects incoming Video signal, and adjusts
itself to optimize its performance.
When Video System is 1035i or 1080i, select system manually first.
AV SYSTEM Menu icon
This box indicates system
being selected.
COMPONENT VIDEO SIGNAL FORMAT
If projector can not reproduce proper video image, it is necessary to
select a specific component video signal format among 480i, 575i,
480p, 575p, 720p, 1035i and 1080i.
Move the pointer to
system and press
SELECT button.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Cinema, Image 1, Image 2,
Image 3 and Image 4 by pressing IMAGE button on Top control panel
or on Remote Control Unit.
IMAGE button
Standard
Cinema
Image 1
Image 2
Image 3
Image 4
Standard
Normal picture level preset on this projector.
Cinema
Picture level adjusted for picture with fine tone.
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P34).
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT button to move the red frame pointer to
IMAGE SELECT Menu icon.
IMAGE SELECT MENU
1
2
Press the POINT DOWN button to move the red frame pointer to
level that you want to set and then press SELECT button.
IMAGE SELECT
Menu icon
Standard
Normal picture level preset on this projector.
Cinema
Move the red frame pointer to
level and press SELECT button.
Picture level adjusted for picture with fine tone.
IMAGE 1~4
Level being selected.
User preset picture adjustment in IMAGE ADJUST Menu (P34).
32
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
IMAGE LEVEL ADJUSTMENT
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT button(s) to move the red frame pointer
to IMAGE ADJUST Menu icon.
IMAGE ADJUST MENU
1
2
Press the POINT DOWN button to move the red frame pointer to
the item you want to adjust and then press SELECT button. The
level of each item is displayed. Adjust each level by pressing the
POINT LEFT/RIGHT button(s).
IMAGE ADJUST
Menu icon
Move the red frame pointer to
the item to be selected and
then press SELECT button.
Contrast
Press the POINT LEFT button to decrease contrast, and the POINT
RIGHT button to increase contrast. (From 0 to 63.)
Brightness
Press the POINT LEFT button to decrease brightness, and the
POINT RIGHT button to increase brightness. (From 0 to 63.)
Color
Press the POINT LEFT button to lighten color, and the POINT
RIGHT button to deeper color. (From 0 to 63.)
Press the POINT LEFT/RIGHT but-
tons to adjust value.
Tint
Press SELECT button at this icon to
display other items.
Press the POINT LEFT button or the POINT RIGHT button to obtain
proper color. (From 0 to 63.)
White balance (Red)
Press SELECT button at this icon to
display previous items.
Press the POINT LEFT button to lighten red tone and the POINT
RIGHT button to enhance red tone. (From 0 to 63.)
White balance (Green)
Press the POINT LEFT button to lighten green tone and the POINT
RIGHT button to enhance green tone. (From 0 to 63.)
Press the POINT LEFT/RIGHT but-
tons to adjust value.
White balance (Blue)
Press the POINT LEFT button to lighten blue tone and the POINT
RIGHT button to enhance blue tone. (From 0 to 63.)
Sharpness
Press the POINT LEFT button to soften image, and the POINT
RIGHT button to sharpen image. (From 0 to 15.)
Press SELECT button at this icon to
store value.
Gamma
Press either the POINT LEFT button or the POINT RIGHT button to
obtain better balance of contrast. (From 0 to 15.)
NOTE :
Tint can not be adjusted when video system is
PAL, SECAM, PAL-M or PAL-N.
Noise reduction
Press the POINT LEFT/RIGHT button(s) to enable noise reduction
mode. Dialog box display is changed to “On” to reduce noises (rough
Noise Reduction can not be operated when video
signal types and systems as follow.
parts) from the image. Press the POINT LEFT/RIGHT button(s) again ✽✽Composite video signal (SECAM, NTSC4.43,
PAL-M and PAL-N systems).
to change the noise reduction mode to “Off”.
✽✽S-video signal (SECAM, PAL-M and PAL-N
Progressive scan
systems).
✽✽Component video signal.
Press the POINT LEFT/RIGHT button(s) to enable progressive scan
mode. Dialog box display is changed to “Off” and progressive scan
mode is set to “Off”. Press the POINT LEFT/RIGHT button(s) again to
change the progressive scan mode to “On”.
Progressive can not be operated when “480p”,
“575p”, “720p”, “1035i” or “1080i” is selected on AV
SYSTEM MENU (P31).
33
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
Store
3
To store adjustment data, move the red frame pointer to Store
icon and press SELECT button. Image Level Menu will appear.
Move the red frame pointer to Image Level 1 to 4 and then press
SELECT button.
Image Level Menu
Other icons operate as follows.
Move the red frame pointer
to image icon to be set and
then press SELECT button.
Reset
Reset all adjustment to previous settings.
Quit
Store icon
Closes IMAGE MENU.
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen adjustment function, which enables you to display the desirable image size.
Press MENU button and ON-SCREEN MENU will appear. Press
the POINT LEFT/RIGHT button(s) to move the red frame pointer
to SCREEN Menu icon.
SCREEN MENU
1
2
Press the POINT DOWN button and move the red frame pointer
to function that you want to select and then press SELECT
button.
SCREEN Menu icon
Move the red frame to the function and
press SELECT button.
Normal
Provides image at a normal video aspect ratio of 4 : 3.
NOTE : SCREEN Menu can not be operated when
“720p,” “1035i,” or “1080i” is selected on AV
SYSTEM Menu (P31).
Wide
Provides image at a wide screen ratio of 16 : 9.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
SETTING MENU
Press MENU button and ON-SCREEN MENU will appear. Press
SETTING MENU
1
2
the POINT LEFT/RIGHT button(s) to move a red-frame pointer
to SETTING icon.
Press the POINT DOWN button to move a red-frame pointer to
Set a red frame
SETTING Menu icon
item that you want to set and then press
Setting dialog box appears.
SELECT button.
pointer to item and
press SELECT
button.
Language
Language used in ON-SCREEN MENU is selectable from among
English, German, French, Italian, Spanish, Portuguese, Dutch,
Swedish, Chinese, Korean and Japanese.
Keystone
When image is distorted, select Keystone. The ON-SCREEN MENU
will disappear and the Keystone dialog box will appear. Correct
keystone distortion by pressing the POINT UP/DOWN/LEFT/RIGHT
button(s). Refer to KEYSTONE ADJUSTMENT on page 20.
When pressing SELECT
button at Language,
Language Menu appears.
Blue back
When this function is “On,” this projector will produce a blue image
instead of video noise on screen when any input source is unplugged
or turned off.
Display
This function decides whether to display On-Screen Displays.
On ··· shows all On-Screen Displays.
Off ···· sets On-Screen Displays disappeared except;
✽ ON-SCREEN MENU
✽ “Power off?” message
Logo
When this function is “On,” the projector displays the “CHRISTIE” logo
when starting up.
Move a pointer to item and
then press the POINT
LEFT/RIGHT button(s).
Ceiling
When this function is “On,” picture is top / bottom and left / right
reversed. This function is used to project image from a ceiling mounted
projector.
Ceiling function
Rear
When this function is “On,” picture is left / right reversed. This function is
used to project image to a rear projection screen.
Power management
This function turns Projection Lamp off when this projector detects
signal interruption and is not used for a certain period in order to
reduce power consumption and maintain Lamp-life. (This projector is
shipped with this function ON.)
Rear function
Power Management function operates to turn Projection Lamp off
when input signal is interrupted and any button is not pressed over 5
minutes. This function operates as follows;
1. When any input signal is interrupted, “No signal” and counting
down display appears (for 5 minutes).
2. After counting down for 5 minutes, projector lamp and READY
indicator are turned off.
3. When READY indicator flashing, Projection Lamp can be turned
on again (Power Management mode).
In this Power Management mode, Projection Lamp is
automatically turned on when input signal connected or projector
is operated with any button on Top control panel or on Remote
Control Unit again.
Time left until Lamp off.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
On start
When this function is “On,” projector is automatically turned on just
by connecting AC Power cord to a wall outlet.
Note ; Be sure to turn projector off properly (refer to section
“TURNING OFF PROJECTOR” on P19). If projector is turned
off in wrong steps, On Start function does not operate
properly.
Lamp mode
When selecting the
brightness and set itself into low power consumption mode.
(Eco) mode, the projector reduces the
"
"
Press SELECT button at this icon to
display other items.
Remote control
This projector has two different remote control codes; factory-set
normal code (Code 1) and secondary code (Code 2). This switching
function prevents remote control operation mixture (jam) when
operating several projectors or video equipment together.
When operating projector in “Code 2,” both projector and Remote
Control Unit must be switched to “Code 2.”
On start
To change code of Projector;
Press SELECT button at this icon to
display previous items.
Set Remote control in SETTING MENU to “Code 2.”
To change code of Remote Control Unit;
Press both MENU and IMAGE buttons on Remote Control Unit
together for over 10 seconds.
Move pointer to item and then press
the POINT LEFT/RIGHT button(s).
After changing code, make sure Remote Control operates properly.
To return to normal code (Code 1), operate both projector and
Remote Control in ways above again.
NOTE : When batteries of Remote Control Unit are replaced or ALL-
OFF switch is turned to “ALL-OFF,” remote transmit code
automatically returns to normal code (Code 1).
USB
This Projector is equipped with USB port for interactive operation
between a projector and a computer. Follow the steps below for USB
setup
Wireless Mouse mode
Select "
" when controlling a computer with Remote Control of
this projector.
Projector mode
Select "
" when controlling a projector with computer.
NOTE: Before you control a projector by computer, install USB driver
(optionally sold parts) and set up computer following instruc-
tion in USB driver package. Contact your authorized dealer.
ChristieNet
This function can not be adjusted when the ChristieNet (optional
part) is not attached to the projector.
Refer to the owner's manual of the optional ChristieNet for operating
instructions
36
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING/APPENDIX
Lamp counter reset
Lamp
counter reset
This function is used to reset Lamp Replace Counter. When
replacing Projection Lamp, reset Lamp Replace Counter by using
this function. Refer to page 39 for operation.
Quit
Closes SETTING MENU.
Move pointer to Lamp counter reset and then press
SELECT button. Message “Lamp replace counter
reset?” is displayed.
OPERATING WIRELESS MOUSE
The Wireless Remote Control Unit is not only able to operate this projector but also be used as a wireless mouse for most
Personal Computers. POINT buttons and two CLICK buttons are used for wireless mouse operation.
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen. When ON-
SCREEN MENU or any message / dialog box is displayed on screen instead of PC mouse pointer, this Wireless Mouse
function can not be used.
INSTALLATION
To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of mouse driver (not supplied)
is required. Make sure that mouse driver is properly installed in your computer. And make sure that mouse port (or USB
port) of a Personal Computer is activated.
Connect mouse port (or USB port) of your computer to Control
Port (or USB connector) of this projector with Control Cable (or
USB cable). (Refer to page 11, 12 for connection.)
Note : When your computer has no mouse
1
port, connect Serial Port of your
computer to Control Port of a projector
with Control Cable for Serial Port.
Turn a projector on first, and then turn on your computer. When
computer is switched on first, Wireless Mouse may not work
properly.
2
OPERATING WIRELESS MOUSE
When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK
button on Wireless Remote Control Unit.
POINT button
POINT button (Move pointer)
Used to move PC mouse pointer. Pointer is moved corresponding
with direction you are pressing.
SELECT (LEFT CLICK) button
This button has same function as left button in a PC mouse.
RIGHT CLICK button
This button has same function as right button in a PC mouse. This
button is not available for controlling this projector.
SELECT button
(left button of mouse)
RIGHT CLICK button
(right button of mouse)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
MAINTENANCE
WARNING TEMP. INDICATOR
WARNING TEMP. Indicator flashes red when the internal temperature of the projector exceeds the normal temperature.
This Indicator stops flashing when the temperature of the projector returns to normal.
When WARNING TEMP. Indicator continues to flash, check items listed below.
Ventilation Slots of the projector may be blocked. In such an event, reposition the projector so that Ventilation Slots are
not obstructed.
1
Air Filter may be clogged with dust particles. Clean Air Filter by following the section AIR FILTER CARE AND
CLEANING below.
2
If WARNING TEMP. Indicator remains on after performing the above checks, the Cooling Fans or the Internal Circuits
may be malfunctioning. Contact service personnel from an authorized dealer or a service station.
3
AIR FILTER CARE AND CLEANING
The Air Filter prevents dust from accumulating on the surface of the Projection Lens and the Projection Mirror. Should Air
Filter become clogged with dust particles, it will reduce Cooling Fans’ effectiveness and may result in internal heat build up
and adversely affect the life of the projector. Clean the Air Filter following the steps below:
Turn off the projector and disconnect the AC Power Cord from
the AC outlet.
1
Turn the projector upside down and remove the Air Filters (2
used) by pulling the latches upward.
2
Clean the Air Filter with a brush or wash out the dust and
particles.
3
Replace the Air Filter properly. Make sure the Air Filter is fully
inserted.
4
CAUTION
Do not operate the projector with the Air Filter removed.
Dust may accumulate on LCD Panel and Projection Mirror
degrading picture quality.
Do not put small parts into Air Intake Vents. It may result
AIR FILTER
Pull up and remove.
in malfunction of the projector.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating the projector. Usage in these environments
may cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on the lens, liquid crystal panels, or optical elements
inside the projector. This condition may degrade the quality of the projected image.
When the above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.
CLEANING PROJECTION LENS
Follow these steps to clean Projection Lens:
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.
1
Lightly wipe a cleaning cloth over Projection Lens.
2
3
When the projector is not in use, replace the Lens Cover.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP REPLACEMENT
When the life of the Projection Lamp of this projector draws to an end, LAMP REPLACEMENT indicator lights yellow. When
a projected image becomes dark or the color of an image becomes unnatural, replacement of Projection Lamp is required.
CAUTION
CAUTION
For continued safety, replace with a lamp
assembly of same type.
Allow the projector to cool for at least 45
minutes before you open Lamp Cover. The
inside of the projector can become very hot.
Do not drop a lamp assembly or touch a glass
bulb! The glass can shatter and may cause
injury.
Follow these steps to replace lamp assembly.
Turn off a projector and disconnect AC plug. Allow a projector to
cool for at least 45 minutes.
1
Loosen 2 screws with a screwdriver and open Lamp Cover.
2
3
Loosen 2 screws with a screwdriver and pull out Lamp Assembly
by grasping Handle.
LAMP COVER
Replace Lamp Assembly with a new one and tighten 2 screws
back. Make sure that Lamp Assembly is set properly. Replace
Lamp Cover and tighten 2 screws.
4
LAMP
ASSEMBLY
HANDLE
Connect AC Power Cord to a projector and turn it on.
5
6
Reset Lamp Replace Counter (refer to section “Lamp Replace
Counter” below).
NOTE : Do not reset Lamp Replace Counter when Projection
Lamp is not replaced.
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering Projection Lamp, give the following
information to the dealer.
✽ Model No. of your projector : 38-VIV206-01
✽ Replacement Lamp Type No. : 03-000667-01P
(Service Parts No. 610 297 3891)
LAMP REPLACE COUNTER
Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP
REPLACE Indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT button(s)
to move the red frame pointer to SETTING Menu icon (refer to page 37).
1
Press the POINT DOWN button to move the red frame pointer to “Lamp counter reset” and then press
The message "Lamp replace counter reset?" will display. Move pointer to [Yes] and then press SELECT button.
SELECT button.
2
3
Another confirmation dialog box will appear and select [Yes] to reset Lamp Replace Counter.
Do not reset Lamp Replace Counter unless Projection Lamp is replaced.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected the projector to your computer or video equipment as described in section "CONNECTING
PROJECTOR" on pages 11 ~ 13.
2. Check cable connection. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If the projector still does not produce an image, re-start your computer.
5. If an image still does not appear, unplug the projector from your computer and check your computer monitor's display.
The problem may be with your graphics controller rather than with the projector. (When you reconnect the projector, be
sure to turn the computer and monitor off before you power up the projector. Power equipment back on in order of :
Projector and computer.)
6. If problem still exists, check following chart.
Problem:
No power.
Try these Solutions
✽ Plug the projector into your AC outlet.
✽ Make sure READY Indicator lights.
✽ Wait 90 seconds after the projector is turned OFF before turning the projector back on.
NOTE : After pressing Power ON-OFF button to OFF, make sure the projector works as
follows:
1. LAMP indicator lights bright and READY indicator turns off.
2. After 90 seconds, READY indicator lights green again and the projector may be
turned on by pressing Power ON-OFF button.
✽ Check WARNING TEMP. indicator. If indicator flashes red, the projector can not be
turned on.
(See "TURNING ON/OFF PROJECTOR" section on page 19.)
✽ Check Projection Lamp. (Refer to page 39.)
✽ Adjust focus of the projector.
✽ Make sure the projection screen is at least 4.6’ (1.4m) from the projector.
✽ Check Projection Lens to see if it needs cleaning.
Image is out of
focus.
NOTE : Moving the projector from a cool temperature location to a warm temperature
location may result in moisture condensation on Projection Lens. In such an event,
leave the projector OFF and wait until condensation disappears.
✽ Check Ceiling / Rear feature. (See “SETTING” section on page 35.)
Picture is Left/Right
reversed.
✽ Check Ceiling feature. (See “SETTING” section on page 35.)
Picture is
Top/Bottom
reversed.
✽ Check Display feature.(See “SETTING” section on page 35.)
Some displays are
not seen during
Operation.
✽ Check connection between your computer or video equipment and the projector.
✽ When turning the projector on, it takes about 30 seconds to display an image.
✽ Check system that you select is corresponding with your computer or video equipment.
✽ Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).
No image.
✽ Check audio cable connection from audio input source.
✽ Adjust audio source.
No sound.
✽ Press VOLUME (+) button.
✽ Press MUTE button.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Problem:
Remote Control Unit
does not work.
Try these Solutions
✽ Check batteries.
✽ Check ALL-OFF switch on Remote Control Unit is set to “ON.”.
✽ Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
✽ Make sure you are not too far from the projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m).
✽ Make sure the code of the Remote Control is set to conform to the projector.
(See the “SETTINGS” section on page 36.)
✽ Check the cable connection between the projector and your computer.
✽ Check mouse setting on your computer.
✽ Turn the projector on before turning on the computer.
Wireless Mouse
function does not
work.
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.
You can often correct operating problems yourself. If the projector fails to work properly, see the "TROU-
BLESHOOTING" section on pages 40 and 41.
If after following all operating instructions, you find that service is necessary, contact the Christie Service Station
or store where you purchased the unit.
Give the model number and explain the difficulty. We will advise you how to obtain service.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
41
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TECHNICAL SPECIFICATIONS
Multi-media Projector
Projector Type
12.6" x 6.6" x 16.8" (319 mm x 168 mm x 429.5 mm)
15.7 lbs (7.1 kg)
(W x H x D)
Dimensions
Net Weight
1.3" TFT Active Matrix type, 3 panels
1024 x 768 dots
LCD Panel System
Panel Resolution
Number of Pixels
Color System
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i and 1080i
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Up and Down
High Definition TV Signal
Scanning Frequency
Motorized Lens Shift
Horizontal Resolution
Projection Lamp
Input 1 Jacks
800 TV lines (HDTV)
275 watt type
DVI Terminal (Digital), HDB 15-pin Terminal (Analog)
and Stereo Mini Type Jack (Audio)
BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H and V), Stereo Mini
Type Jack (Audio)
Input 2 Jacks
Input 3 Jacks
Other Jacks
RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L)
and DIN 4-pin (S-Video)
DIN 8-pin (Control port), USB port (Series B receptacle), Wired Remote Jack
and ChristieNet Connector
INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)
Built-in Speakers
0˚ to 10.5˚
Feet Adjustment
Voltage and
Power Consumption
Operating Temperature
AC 100 ~ 120 V (4.8 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)
AC 200 ~ 240 V (2.4 A Max. Ampere), 50 / 60 Hz (Continental Europe)
41 F ~ 95 F (5 ˚C ~ 35 ˚C)
14 F ~ 140 F (-10 ˚C ~ 60 ˚C)
Storage Temperature
Power Source
Operating Range
Dimensions
Net Weight
Laser Pointer
:
:
:
:
:
AA, UM3 or R06 Type x 2
16.4’ (5m) / ±30˚
2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
0.36 lbs (165 g) (including batteries)
(Max. Output : 1mW / Wave length : 650±20nm)
Class II Laser
Remote Control Transmitter
User’s Manual
Accessories
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
Remote Control Cable
VGA Cable
MAC/VGA Adapter
3 Types Control Cable (For PS/2, Serial and ADB port)
Protective Dust Cover
✽ Specifications are subject to change without notice.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
CONFIGURATIONS OF TERMINALS
COMPUTER INPUT-1 TERMINAL (ANALOG)
Terminal : HDB15-PIN
Connect the display output terminal of the computer to this terminal with the VGA Cable (supplied). When connecting the
Macintosh computer, the MAC Adapter (supplied) is required.
1
2
3
4
5
6
7
8
Red Input
Green Input
Blue Input
Sense 2
9
+5V Power
Pin Configuration
10 Ground (Vert.sync.)
11 Sense 0
2
1
5
4
3
12 DDC Data
10
9
8
7
6
15
14
13
12
11
Ground (Horiz.sync.) 13 Horiz. sync.
Ground (Red)
Ground (Green)
Ground (Blue)
14 Vert. sync.
15 DDC Clock
COMPUTER INPUT-1 TERMINAL (DIGITAL)
Terminal : DVI 24-pin
Connect the display output terminal of the computer to this terminal with a DVI cable (for Single Link T.M.D.S. / not supplied).
1
2
3
4
5
6
7
8
T.M.D.S. Data2–
9
T.M.D.S. Data1–
17 T.M.D.S. Data0–
18 T.M.D.S. Data0+
Pin Configuration
T.M.D.S. Data2+
10 T.M.D.S. Data1+
T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield
1
9
2
3
4
5
6
7
8
No Connect
No Connect
DDC Clock
DDC Data
12 No Connect
13 No Connect
14 +5V Power
20 No Connect
10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
21 No Connect
22 T.M.D.S. Clock Shield
23 T.M.D.S. Clock+
24 T.M.D.S. Clock–
15 Ground (for +5V)
16 Hot Plug Detect
No Connect
CONTROL PORT CONNECTOR
Terminal : Mini DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this connector with the Control Cable (supplied).
PS/2
-----
Serial
R X D
-----
ADB
-----
Pin Configuration
1
2
3
4
5
6
7
8
CLK
DATA
GND
-----
ADB
-----
-----
8
7
6
GND
GND
-----
5
4
3
RTS / CTS
T X D
GND
2
1
-----
-----
GND
-----
-----
GND
GND
USB CONNECTOR (Series B)
Connect USB port terminal on your computer or peripheral equipment to this connector with USB Cable (not supplied).
Pin Configuration
1
2
3
4
Vcc
- Data
+ Data
Ground
2
3
1
4
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in Japan
Part No. 10-A 610 302 1201 (1AA6P1P3600-- MA8KM)
Download from Www.Somanuals.com. All Manuals Search And Download.
|