1
CCH00701:09/00 JCHE p65
15061,16101,16151,16191,16281
DOUBLEDROPSIDE CRIB
child craft
CHILD CRAFT INDUSTRIES, INC.
P.O. Box 444, Salem, IN USA 47167-0444
ASSEMBLY DIRECTIONS AND PARTS LIST
ΦREADALLINSTRUCTIONSWITHCAREBEFORESTARTINGTHEASSEMBLYPROCEDURE.
Φ YOUWILLNEEDA#2PHILLIPSSCREWDRIVER,ASLOTTEDSCREWDRIVERANDAHAMMER.
PARTS ENCLOSEDIN HARDWARE BAG(NOTED WHEN SHOWN ACTUAL SIZE)
(12) Slotted/Phillips
Machine Screws
(4) Spring Hangers
(4) Gate Shoes
(18) Slotted/Phillips
Wood Screws
A
B
C
D
E
(2)
Moulded
plastic
(actual size)
(actual size)
(2)
4-Position
Spring
Hanger
Brackets
backers
(4) Casters
(style may vary)
(4) Compression
(4) Bumper
Springs
(2) Angle
Brackets
F
G
H
I
Springs
PARTS INCLUDED IN CARTON
(1) Spring
(1) Footboard
(1) Headboard
(2) Stabilizer Bars
O
N
P
&
Q
R
J
K
(2) Crib sides
(Dropsides)
(4) Crib Rods
PREPARATION
Carefully remove and lay out all hardware and parts. Remove wires securing the (2) Stabilizer Bars J and the (4) Crib Rods K to Crib Spring R. Check
quantities and match to the three Parts Lists above. If any part is missing or broken contact your dealer or Child Craft (P.O. Box 444, Salem, IN 47167-
0444 USA (ph# 812/883-3111), [email protected] for a replacement part or instructional literature. Before making this contact, identify your crib.
A model identification number is stamped on the underneath side of the bottom rail of either a crib end N/O or a crib side P/Q. Record the model
Identification Number now: # ______________________. Include this number with a request for a part or instructional literature. DO NOT SUBSTITUTE
PARTS!
STEP 1-DIAGRAM 1:ATTACH OF 4-POSITION SPRING HANGER BRACKETS AND ANGLE BRACKETS.
Note the two piece assembly of 4-Position Spring Hanger Brackets D. Before
attachment to crib (ends) N &O, check to be sure the moulded plastic backer
aligns with the 4-Position Spring Hanger Bracket D as shown. These items are
shipped assembled, in the unlikely event they should become detached during
shipment, simply take the plastic backer, align with the holes in the metal bracket
O
and snap together to create an assembly as shown in the Hardware Parts Diagram.
Holes to
IMPORTANT! All four plastic tabs on each moulded plastic backer should project
toward the metal hooks on 4-Position Spring Hanger Brackets D. If you should
find a tab on an uninstalled 4-Position Spring Hanger Bracket not so projected,
simply use a screwdriver to push tab forward until it contacts the metal hook. If
a plastic tab is not projected on a factory installed 4-Position Spring Hanger Bracket
simply place a small slotted screwdriver underneath the plastic tab and pull
forward until it contacts the metal hook. Attach a 4-Position Spring Hanger Bracket
D, (2 piece assembly), to both Headboard N & Footboard O with Slotted/Phillips
Wood Screws E, to be positioned exactly as the ones already factory installed.
Attach Angle Brackets I with Slotted/Phillips Wood Screws E to Headboard N
and Footboard O, to be positioned exactly as the ones already factory installed.DO
NOT REMOVE 4-POSITION SPRING HANGER BRACKETS OR ANY OTHER
HARDWARE ITEMATTACHEDWITHSLOTTED/PHILLIPSWOODSCREWS E.
D
receive
Slotted/
Phillips
Wood
Screws
E
D
E
Factory
installed
I
E
Download from Www.Somanuals.com. All Manuals Search And Download.
3
CCH00701:09/00
MAIN DIAGRAM 6
TIGHTEN SCREW A MANUALLY, DO NOT USE ANY TYPE OF POWER SCREWDRIVER.
O
N
A
A
K
K
P / Q
Top rail
D
Plastic
pouch
B
J
F
G
I
H
Locate the 4 Casters H, insert each into a
Foot latch
lower corner post of Headboard N/Footboard
O. Refer to Main Diagram 6. (Caster H
design may possibly vary according to your
particular crib model.)
P / Q
Bottom rail
CAUTION: If crib is placed on exception-
ally thick carpet, take care when crib is
rolled as Casters H could catch on thick
carpet pile and possibly cause breakage
or damage to lower corner posts of crib.
CLOSE UP VIEW
K
D
Hook end
down
CRIB SPRING R:
R
Be sure the smooth side of wire is
placed up as illustrated. Also,style
of Crib Spring R may differ with
your model of crib.
H
B
J
Permanent Storage of Assembly Instructions: After completing the assembly
process you are advised to read and be aware of all WARNINGS, CAUTIONS,
CLEANING, STORAGE, USE, and MAINTENANCE notices contained in this set of
assembly directions and printed on the plastic pouch located on the underneath side of
crib spring. You will then place this complete set of assembly directions into the plastic
pouch for future referral. We caution you not to place excess hardware in the plastic
pouch as it could present danger to a small child if retrieved.
Place a purchased mattress on Crib Spring R and crib is ready for use.
TO RAISE & LOWER CRIB DROPSIDE: To lower lift the dropside
slightly, pushthefootlatchtowardtheinsideofcribwhichwillrelease
thedropsidetothelowest or"DOWN"position.Toraisethedropside,
lift up on the dropside, rail will then lock into the "UP" position.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
CCH00701:09/00
WARNING
CAUTION
!
▲
Φ ANY MATTRESS USED IN THIS
CRIB MUST BE AT LEAST 27-1/4
INCHES (69 CENTIMETERS), BY 51-
5/8 INCHES (131 CENTIMETERS),
WITH A THICKNESS NOT EXCEED-
ING 6 INCHES (15 CENTIMETERS).
thedimensionsofthemattressshall
betakenfromseamtoseamoredge
to edge where appropriate.
Φ FAILURE TO FOLLOW THESE WARNINGS AND ASSEM-
BLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY
OR DEATH.
Φ READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB.
KEEP INSTRUCTIONS FOR FUTURE USE. A plastic pouch
is attached to crib spring for permanent storage of the
instructionalliterature.
Φ BEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB
FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING
PARTS OR SHARP EDGES. DO NOT USE CRIB IF ANY
PARTSAREMISSINGORBROKEN.ASKYOURDEALEROR
CHILD CRAFT, P.O. BOX 444, SALEM, IN 47167-0444 USA
(812/883-3111) [email protected] FOR REPLACE-
MENT PARTS AND INSTRUCTIONAL LITERATURE IF
Φ UPON COMPLETION OF ASSEM-
BLY BE SURE ALL SCREWS,
BOLTS AND FASTENING DEVICES
HAVE BEEN TIGHTENED SE-
CURELY. A FREQUENT CHECK
NEEDED. INCLUDE MODEL IDENTIFICATION NUMBERS SHOULD BE MADE OF ALL
WITH YOUR REQUEST WHICH YOU RECORDED ON PAGE
ONE. DO NOT SUBSTITUTE PARTS.
SCREWS, BOLTS AND FASTENING
DEVICES AND TIGHTEN IF
NEEDED.
MAINTENANCEOFYOURCHILDCRAFTCRIB:Upon
completion of assembly be sure all screws, bolts and
fastening devices have been tightened securely. A
frequent periodic check should be made of all screws,
bolts and fastening devices and tighten if needed. Before
each usage or assembly, inspect crib for damaged
hardware, loose joints, missing parts or sharp edges. DO
NOT use crib if parts are missing or broken. Ask your
Φ AFTER RAISING SIDE, MAKE SURE LATCHES ARE SE-
CURE.
Φ WHEN CHILD IS ABLE TO CLIMB OUT OR REACHES THE
HEIGHTOF35INCHES(90CENTIMETERS)THECRIBSHALL
NO LONGER BE USED.
Φ DO NOT PLACE CRIB NEAR WINDOW WHERE CORDS
Dealer
or
Child
Craft
(812/883-3111),
FROM BLINDS OR DRAPES MAY STRANGLE A CHILD.
[email protected] for replacement parts and
instructional literature if needed. Include Model Identifi-
cation Number with your request which you recorded on
page 1. DO NOT substitute parts. DO NOT make any
alteration to this crib.
CLEANINGINSTRUCTIONSFORYOURCHILDCRAFT
CRIB: Mixtogetheramildsolutionofgentledishwashing
liquid and water, apply to crib surface using a soft clean
cloth lightly dampened in the solution. Rinse with clear
water again using a soft clean cloth then dry all surfaces
thoroughly with a soft dry cloth. NO ABRASIVE CLEAN-
ERS, SCOURING PADS, STEEL WOOL, OR COARSE
RAGSSHOULDBEUSEDTOCLEANTHISFINEFURNI-
TURE.
Φ IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED
FOR CHILDREN'S PRODUCTS.
Φ DO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE
SURE SIDE IS IN RAISED AND LOCKED POSITION WHEN-
EVER CHILD IS IN CRIB.
Φ WHENCHILDISABLETOPULLTOSTANDINGPOSITION,
SET MATTRESS TO LOWEST POSITION AND REMOVE
BUMPERPADS,LARGETOYSANDOTHEROBJECTSTHAT
COULD SERVE AS STEPS FOR CLIMBING OUT.
STORAGEANDUSEOFYOURCHILDCRAFTCRIB:
A
Φ NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLAS-
TIC FILM AS MATTRESS COVERS BECAUSE THEY CAN
CAUSE SUFFOCATION.
printed plastic pouch is attached to the crib spring for the
permanent storage of the assembly directions. After
completing the assembly process you are advised to
readandbeawareofallWARNINGS,CAUTIONS,CLEAN-
ING,STORAGE,USEANDMAINTENANCEnoticescon-
tained in this set of assembly directions and printed on
the plastic pouch located on the underneath side of crib
spring. You will then place the complete set of assembly
directions into the plastic pouch for future referral. We
caution you not to place excess hardware in the plastic
pouch as it could present danger to a child if retrieved and
it could also puncture crib mattress. When storing crib
use CAUTION as extreme temperature or humidity
changes could be harmful. Use CAUTION when a vapor-
izer is in use, always aim vaporstream away from crib
as well as away from any other wood furniture item.
Φ DO NOT USE A WATER MATTRESS WITH THIS CRIB.
Φ REPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE.
Φ STRINGSCANCAUSESTRANGULATION!DONOTPLACE
ITEMS WITH A STRING AROUND A CHILD'S NECK, SUCH
AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUS-
PEND STRINGS OVER A CRIB OR ATTACH STRINGS TO
TOYS.
Φ REMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS
CRIB AREA WHEN YOUR CHILD IS BEGINNING TO PUSH
UP ON HANDS AND KNEES OR IS 5 MONTHS OF AGE,
WHICHEVER OCCURS EARLIEST. THESE TOYS CAN
CAUSE STRANGULATION!
CCH00701:09/00 JCHE p65
madeinusa
Φ WHEN DISASSEMBLING THIS CRIB, DO NOT REMOVE
ANY ITEM ATTACHED WITH WOOD SCREWS.
Φ ALWAYS ENSURE A SAFE ENVIRONMENT FOR THE
CHILD BY CHECKING REGULARLY, BEFORE PLACING
THE CHILD IN THE CRIB, THAT EVERY COMPONENT IS
PROPERLY AND SECURELY IN PLACE.
CHILDCRAFTINDUSTRIES,INC.
P.O. Box 444, Salem, IN USA 47167-0444
PH: 812-883-3111 - FAX: 812-883-1819
Download from Www.Somanuals.com. All Manuals Search And Download.
|