I N S T A L L A T I O N I N S T R U C T I O N S
LVS1U
LVSXU
ConnexSys™ Video Wall Mounting System
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
LVS1U / LVSXU
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
LVS1U / LVSXU
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ....................................2
TABLE OF CONTENTS ...............................................................3
LEGEND ......................................................................................4
DIMENSIONS ..............................................................................5
TOOLS REQUIRED FOR INSTALLATION .................................6
PARTS .........................................................................................6
LET’S GET STARTED! Measurements You’ll Need ....................7
STRUT CHANNEL REQUIREMENTS (LVSXU) ..........................8
MOUNTING PATTERN OFFSET CALCULATION ......................8
ATTACHING STRUT CHANNEL OR RAIL .................................9
HANGING LVS1U/LVSXU MOUNT ON RAIL .............................10
Preparing Strut Channel (LVSXU only) ..................10
Hanging Mounts .....................................................10
INSTALLING INTERFACE BRACKETS ......................................11
ADDING DISPLAYS TO MOUNTS ..............................................11
ADJUSTMENTS ..........................................................................12
COMPLETING THE INSTALLATION ..........................................14
Cable Management Clips .......................................14
Security ...................................................................14
FASTENER INSTALLATION METHODS ....................................14
Wood Stud ..............................................................14
Concrete .................................................................14
Plywood-Backed Steel Stud ...................................15
SERVICE .....................................................................................16
Extending and Retracting Mount ............................16
Interface Bracket Kickstands ..................................16
RapidDraw Display Release ...................................16
3
Download from Www.Somanuals.com. All Manuals Search And Download.
LVS1U / LVSXU
Installation Instructions
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Potloodmerkteken
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
LVS1U / LVSXU
DIMENSIONS
LVS1U
27.56
[700]
MAX DISPLAY
PATTERN WIDTH
3.99
101.4
MIN DEPTH
1.00
25.4
HEIG HT
ADJUST
17.47
443.7
DIMENSIONS:
INCHES
[MILLIMETERS]
LVSXU
27.56
[700]
MAX DISPLAY
PATTERN WIDTH
3.99
101.4
MIN DEPTH
1.00
25.4
HEIG HT
ADJUST
17.47
443.7
WALL RAILS NOT INC LUDED IN LVSXU VERSION. WALL RAILS
SHOWN FOR DEPTH AND POSITION MEASUREMENTS. 13/16" WALL
STRUT SHOWN. IF USING DEEPER C HANNEL ADD IN THE
ADDITIONAL DEPTH.
DIMENSIONS:
INCHES
[MILLIMETERS]
5
Download from Www.Somanuals.com. All Manuals Search And Download.
LVS1U / LVSXU
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
7/16"
1/2"
3/8"
nut driver
7/16"
1/2"
7/32"
3/8"
7/16"
1/2"
3/8"
M3 x 6"
(included)
#2
PARTS
Display Hardware Kit
(Letters correspond to letters on bag)
Concrete and Wood Stud Walls
Install Hardware Kit
K (4)
5/16"
A (4)
M6 x 12
B (4)
M6 x 16
C (4)
M6 x 30
D (4)
3/16"
J (4)
UX10 x 60
L (4)
5/16" x 2-1/2"
H (4)
M8 x 25
F (4)
M8 x 12
G (4)
M8 x 16
E (4)
.75x.344x.5
M (10)
1/4"
S (2)
[Inner stop
clamp]
Q (4)
[Cable clip]
R (2)
[Outer stop
clamp]
P (8)
[7-1/2" cable tie]
N (10)
#14 x 1-1/2"
T (2)
1/4-20 x 1/2"
Plywood-backed Walls
Install Hardware Kit
Cable Management Kit
(LVSXU only)
X (2)
[Interface
bracket]
W (1)
M3 x 6"
V (1)
[Rail]
(LVS1U only)
U (1)
[LVS1U assembly]
OR
Y (1)
[Label sheet]
U (1)
[LVSXU assembly]
PowerZone™ Adjustment Guide
Z (1)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
LVS1U / LVSXU
LET’S GET STARTED! Measurements You’ll Need
Description
Measurement
A - Number of displays in each row
B - Number of displays in each column
C - Width of individual display
D - Height of individual display
E - Total width - (A) x (C)
F - Floor to bottom of display (bottom row) OR Ceiling to top of display
(top row)
G - 1/2 height of display (D) / 2
H - Display mounting pattern offset. (Only applies to some displays.
Calculation instructions on next page.)
I - Strut channel length* (E) – 4" (102mm) (LVSXU only)
J - Number of strut channel lengths (B) x 2 (LVSXU only)
* Check with your local strut channel dealer to determine the lengths available. You may need to buy multiple pieces or cut longer
pieces down to size.
CEILING
I
F
C
D
G
E
F
FLOOR
Figure 1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
LVS1U / LVSXU
Installation Instructions
STRUT CHANNEL REQUIREMENTS (LVSXU)
UNACCEPTABLE strut channel profiles
IMPORTANT ! : Strut channel must be made of steel
with a minimum yield strength of 33ksi (230MPa), and
meeting the profile and dimension requirements outlined.
Table 1: Strut Channel Dimension Requirements
STEEL THICKNESS
14 ga [0.075"] (2.5mm)
12 ga [0.104"] (3mm)
14 ga or 12 ga
DIMENSION (See Figure 2)
K = 13/16" (21mm)
13/16" (21mm) < K < 3-1/4" (83mm)
L (minimum) = 1/4" (6mm)
L (maximum) = 9/32" (7mm)
Strut channel MUST NOT
have holes or slots on
side walls of channel.
Strut channel MUST have
rolled up lips on both sides
of channel.
Strut Channel Profile
1-5/8"
(41mm)
3/8"
Figure 3
(10mm)
7/8"
(22mm)
L
K
IMPORTANT! All dimensions other than "L" and "K"
are nominal requirements.
Figure 2
MOUNTING PATTERN OFFSET CALCULATION
Center line
of display
Mounting
pattern of
display
Center line
of mounting
pattern
Offset (H)
NOTE: An offset measurement (H) is required if the centerline of the display does not match the centerline of the
display mounting pattern.
1. If display mounting pattern is BELOW display centerline: 8-3/4" - H = Distance from display centerline to rail
mounting location.
2. If display mounting pattern is ABOVE display centerline: 8-3/4" + H = Distance from display centerline to rail
mounting location.
Figure 4
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
LVS1U / LVSXU
10. Attach upper rails (V) using Fastener Information. (See
ATTACHING STRUT CHANNEL OR RAIL
IMPORTANT ! : Reference measurements noted on
page 7.
1. Mark distance (F) from floor to desired location for bottom
of display OR from ceiling to desired location for top of
display (if installing top row first). (See Figure 1) and (See
Figure 5)
Table 2)
11. Measure up from attached rails the distance (D) and mark
for next row of rails (V). (See Figure 1) and (See Figure 5)
12. Repeat Steps 4 - 10 for that row of rails.
13. Repeat Step 11 for any remaining rows of rails (V).
2. Mark distance (G) from bottom of display (or top of display)
IMPORTANT ! : See Fastener Installation Methods section
at end of Installation Instructions for details on installing product
into various wall types.
to center line of display. (See Figure 1) and (See Figure 5)
3. Measure up 8-3/4" (222mm) from centerline of display and
mark location for top strut channel/rail attachment.
Table 2: Fastener Information
NOTE: If an offset measurement (H) is needed (See Figure 4):
PILOT
HOLE
FASTENERS (see PARTS
drawing)
WALL
TYPE
•
If display mounting pattern is BELOW display
centerline, measure up: 8-3/4" (222mm) - H
N/A
#14 x 1-1/2" hex slot head screw
(N) & 1/4" washer (M). Fasteners
placed a maximum of 8" (203mm)
apart AND in last slots on each end of
strut channel.
Drywall
•
If display mounting pattern is ABOVE display
centerline, measure up: 8-3/4" (222mm) + H
attached to
plywood-
backedwalls
/Steel studs
4. Level and attach strut channel/rail (V) using the provided
hardware. See Parts drawing, (See Figure 5) and (See
Table 2).
7/32" x 3"
5/16 x 2-1/2" hex head lag (L) &
5/16" washer (K). Fasteners placed
at stud locations, min. 16" (400mm)
and max. 24" (610mm) AND within 9"
(230mm) of each end of the rail/strut
channel.
Wood stud
(2" x 4")
5. Mark distance (D) (up or down) from first strut channel/rail
slots and mark location of next row of strut channel/rail.
6. Repeat for remaining rows of strut channels/rails.
7. (LVSXU only) Proceed to Hanging LVS1U/LVSXU Mount
On Rail section.
3/8" x 3"
5/16 x 2-1/2" hex head lag (L) &
Fischer UX10x60 anchor (J).
Fasteners placed a min. 16" (400mm)
and max. 24" (610mm) apart AND
within 9" (230mm) of each end of the
rail/strut channel.
Concrete
8. (LVS1U only) Measure over (C) (width of display) from
center of first installed rail, level and mark location of
adjacent rail. (See Figure 1) and (See Figure 5)
9. Repeat Step 8 for remaining rails in that row.
Ceiling
1
I
C
2
Top strut channel - LVSXU
3
Centerline - display
D
5
H
D
7
C
Top rail - LVS1U
3
Centerline - display
2
1
Floor
Figure 5
9
Download from Www.Somanuals.com. All Manuals Search And Download.
LVS1U / LVSXU
Installation Instructions
HANGING LVS1U/LVSXU MOUNT ON RAIL
Preparing Strut Channel (LVSXU only)
wall
side
view
1. On the top rail, slide one inner stop clamp (S) into end of
strut channel section. (See Figure 6)
2. Fasten outer stop clamp (R) to inner stop clamp (S) using
one 1/4-20 x 1/2" hex head screw (T). (See Figure 6)
3. Repeat for each end of each top section of strut channel.
3
Stop clamp fastened
in place at each end
of upper row of
strut channel
upper lip
3
lower strut
channel
strut channel
(S)
mount hooks
(R)
1
Figure 8
(T)
2
4. Tighten two hex head fasteners at bottom of each mount.
(See Figure 8)
Figure 6
Hanging Mounts
1. Lift mount and hang it on lower lip of upper strut channel or
rail (V). (See Figure 7)
lower lip of strut
channel or rail
RapidDraw
pull cord
1
1
x 2
5
Figure 9
5. Fasten bottom rail (LVS1U) or lower strut channel (LVSXU)
to wall using the provided hardware. See Parts drawing,
and (See Table 2).
(LVS1U shown as example)
Figure 7
6. Extend RapidDraw pull cord to bottom row of displays so
that it is accessible, re-tie to correct length and label the pull
cord using label (Y) so that it is identifiable. (See Figure 9)
IMPORTANT ! : See Service section for more
information on properly configurating the RapidDraw cord
and display release.
2. Repeat for remaining mounts in that row, and slide mounts
along strut channels to desired location.
3. LVSXU only: Add lower strut channel to bottom of all
mounts in row by lifting strut channel up from below mounts
and setting upper lip of strut channel onto mounts’ latching
hooks. (See Figure 8)
7. Repeat Attaching Strut Channel or Rail and Hanging
LVS1U/LVSXU Mount On Rail sections for each row of
displays.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
LVS1U / LVSXU
5. Make sure diamond on interface brackets is even with
center of display. (See Figure 10)
INSTALLING INTERFACE BRACKETS
1. Place displays face down on a soft, non-abrasive surface.
6. Use selected screws (A-C or F-H), washers (D, if using
screws A, B or C) and spacers (E), if necessary, to connect
interface brackets (X) to back of display. (See Figure 10)
CAUTION: Using screws of improper diameter may
damage your display! Proper screws will easily thread into
display mounting holes.
ADDING DISPLAYS TO MOUNTS
1. Raise display with attached interface brackets and hook top
of brackets into top of mount. (See Figure 11)
2. Select screw diameter by examining hardware (A-C and F-H)
(6mm or 8mm) and comparing with mounting holes on
display. (See Figure 10)
2. Slowly bring bottom of display in towards mount until it clicks
into place.
3. Select spacers:
3. Repeat Steps 1 and 2 for remaining mounts in that row.
•
Spacers are NOT required if mounting holes are not
recessed and interface brackets (X) can lay flat against
display.
(LVS1U shown
as example)
Interface
•
Spacers (E) ARE required if mounting holes are
recessed, or if protrusions prevent interface brackets
(X) from laying flat.
bracket
hooked over
mount
CAUTION: Using screws of improper length may damage
your display! Proper screws will have adequate thread
engagement without contacting bottom of display mounting
holes.
1
4. Select screw length: (See Figure 10)
•
By hand, insert SHORTEST length screw of selected
diameter (A or F) through 3/16" washer (D, if using
screw A), bracket (X), selected spacer (E, if required),
into display mounting hole. Do NOT thread screw into
hole at this time.
1
•
Proper screw length requires base of screw head to
protrude above flat washer (if flat washer is used) a
distance equal to or greater than the screw diameter. If
screw length is inadequate, select longer screw. Select
shortest screw which will protrude the required
distance.
4
5
(A-C or F-H) x 4
6
4
(Display not shown)
(D) x 4
Figure 11
Match diamond
with center of
display
5
4. The displays can be easily removed by pulling both
interface bracket cords down. (See Figure 11)
5. Pull the bottom of the display out.
6. Lift up display to lift hooks off the mount.
(X)
Bracket kickstand
may be raised to
allow hardware
attachment
(E) x 4, if
required
Figure 10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LVS1U / LVSXU
Installation Instructions
ADJUSTMENTS
NOTE: The following steps are also referenced on the next
page (See Figure 16) and the PowerZone
Adjustment guide (Z).
1. Place the level against the front of the display and use knob
3
(#1 in Figure 16) to straighten the tilt. (See Figure 12)
3
1
Figure 14
4. Slide latch mechanism until tab sits flush against the
interface bracket.
5. Pull tab forward to lock latch mechanism to interface
bracket. (See Figure 15)
6. Push latch down to engage the micro lateral adjustment
knobs (#4B and #4C). (See Figure 15) and (See Figure 16)
7. Turn micro lateral adjustment knobs clockwise to move
display toward knob end until displays are in correct
position. (See Figure 16)
Figure 12
(Display not shown)
2. Place a level on top of display and use the knobs at the top
of the interface brackets (#2 in Figure 16), to raise/lower
each side of display and level the display. (See Figure 13)
and (See Figure 16)
Tab
Interface
bracket
Latch
5
4
6
2
2
Figure 13
Figure 15
3. Place level across face of adjoining screens and adjust
depth (#3 in Figure 16) to make displays flush across the
front of the video wall. (See Figure 14) and (See Figure 16)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
LVS1U / LVSXU
Figure 16
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LVS1U / LVSXU
Installation Instructions
COMPLETING THE INSTALLATION
Cable Management Clips
FASTENER INSTALLATION METHODS
IMPORTANT ! : (See Table 2) for appropriate hardware
and pilot hole sizes for various wall types.
1. Place cable clip (Q) into rail and turn 90° in either direction
until cable clip is vertical. (See Figure 17)
2. Route cables and RapidDraw release cords along rails,
through cable clips.
Wood Stud
3. Fasten cables and cords to cable clips (Q) using cable ties
(P).
1. Use one 5/16" x 2-1/2" lag bolt (L) through product and into
pilot hole. (See Figure 19)
2. Repeat for remaining pilot holes.
1
1
(L) x 2
2
Figure 19
Concrete
(Q)
1. Install one UX10 x 60 anchor (J) into each pilot hole using a
hammer, making sure that the anchor is flush with the wall.
(See Figure 20)
Figure 17
Security
2. Use one 5/16" x 2-1/2" lag bolt (L) through product into each
anchor in wall.
The displays may be secured to the mounts by using a padlock
(not included) through the bottom of the interface brackets.
(See Figure 18)
(J)
NOTE: Padlock must have a 1/4" (6mm) shackle diameter.
1
(L)
2
Figure 20
Insert
padlock
Figure 18
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
LVS1U / LVSXU
Plywood-Backed Steel Stud
1. Use one #14 x 1-1/2" hex-head washer slot head screw (N) and one 1/4" washer (M) through strut channel or rail. (See Figure 21)
If back side of wall is unfinished, drywall must be installed
to a minimum of one stud left and right of the stud(s)
being used to install the mount. Drywall must be
secured to studs with screws a maximum of 12" (305mm) apart down center of stud.
16" or 24" (on center) Studs
There must be a minimum of
1-7/8" (48mm) clearance
inside wall
Plywood
FRONT
5/8" minimum thickness
plywood (5 layers) covered
with drywall having
maximum thickness of 5/8"
5/8" maximum
drywall thickness
(Both Sides of Stud)
Steel Stud (2 x 4 / 25ga minimum)
Stud type and structural strength must conform to the North American
Specification for the Design of Cold-Formed Steel Structural Members.
[362 S 125 18, C-Shaped, S-Stud Section]
Figure 21
15
Download from Www.Somanuals.com. All Manuals Search And Download.
LVS1U / LVSXU
Installation Instructions
RapidDraw Display Release
SERVICE
The RapidDraw pull cord and display release allows easy
service access to any specific display in the video wall.
Extending and Retracting Mount
The mounts may be extended and retracted only in a service
situation.
Each mount ships with the pull cord installed. It is installed so
that when pulled from below the mount or from the right of the
mount it will release the display for service.
1. To Extend Mount: Pull on the RapidDraw release cord
designated for the specific mount.
The following steps should be taken if an installation requires
that the pull cord be accessible from the left of the display or
above the display:
2. When the mount releases, carefully grasp bezel edges of
display and pull out slowly, being careful to clear
surrounding displays.
1. Unhook the pull cord from the mount. (See Figure 23)
3. To Retract Mount: Carefully push against display bezel
edges, being careful to clear surrounding displays.
2. Reinstall the pull cord in the opposite hole on the mount.
(See Figure 23)
4. Push display against mount until it clicks into place.
Mount ships with
cord attached here
To release display from
left or above,
reinstall cord
here
Interface Bracket Kickstands
2
The interface brackets are equipped with kickstands which
must only be used in a service situation.
1. Pull down on interface bracket release cords. (See Figure 22)
2. Pull out bottom of display.
3. Flip down the kickstands on both interface brackets, and
prop against mount during service.
Kickstand
2
1
Figure 23
3
Interface bracket
release cords
(Display not shown)
Figure 22
4. After service, hold display while flipping up both kickstands.
5. Slowly bring bottom of display in towards mount until it clicks
into place.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
LVS1U / LVSXU
Installation Instructions
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
LVS1U / LVSXU
18
Download from Www.Somanuals.com. All Manuals Search And Download.
LVS1U / LVSXU
Installation Instructions
19
Download from Www.Somanuals.com. All Manuals Search And Download.
LVS1U / LVSXU
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
6436 City West Parkway, Eden Prairie, MN 55344
800.582.6480 / 952.225.6000
877.894.6918 / 952.894.6918
Franklinstraat 14, 6003 DK Weert, Netherlands
+31 (0) 495 580 852
+31 (0) 495 580 845
Chief, a products division of
Milestone AV Technologies
Asia Pacific
A
Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
852 2145 4099
852 2145 4477
8800-002523 Rev00
¤2014 Milestone AV Technologies
03/14
P
F
Download from Www.Somanuals.com. All Manuals Search And Download.
|