I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
Automated Dual Horizontal Door System
This device complies with part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio or television
communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment to an outlet on a circuit other than that to which the receiver is connected
Consult the dealer or and experienced radio/TV technician for help
CM6DH SERIES
Download from Www.Somanuals.com. All Manuals Search And Download.
CM6DH SERIES
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
1/2" (12.7mm)
#2
PARTS
A (1)
B (1)
G (1)
C (2)
F (2)
D (1)
08 x 1/2"
E (1)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CM6DH SERIES
Installation Instructions
Installing to Cabinet
INSTALLATION
1. Place mechanism (A) on top of cabinet. (See Figure 1)
2. Align center of track with center of the door opening.
3. Attach using #8 or #10 screws through the holes in track.
Cabinet Considerations
1. Header must not extend beyond top of track.
2. Guide wheel must have free play in toe space.
3. Doors must not exceed 50 lbs (each).
4. Allow ample room for drawers to open past doors, and
for doors to move in front of cabinet, as well as above
floor or carpet.
4. Attach motor box to the track following instructions in box.
(See Figure 2)
5. Use of a quality surge protection device is suggested
for mounting on top of cabinet to make electrical
hook-up of the mechanism and lights.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM6DH SERIES
Figure 1
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CM6DH SERIES
Installation Instructions
Figure 2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM6DH SERIES
Hanging and Adjusting Doors
1. Remove door hanger from mechanism by removing locking
screws and washers. (See Figure 3)
Locking Screws
and Washers
Door
Hanger
(F) x 2
Figure 5
Figure 3
4. Move carriages to one half open position by activating
mechanism and pressing button a second time when
carriage reaches desired position. (See Mechanism
Activation section).
2. Center door hanger to top of door and secure with eight flat
head screws of sufficient length to support weight of door.
(See Figure 4)
5. Lift door and engage guidewheel into guidewheel space.
6. Tip top of door in, engaging the pendant bolts into keyhole
in carriage arms. (See Figure 6)
x 8
Keyhole
6
Figure 4
Pendant
Bolts
3. Attach one guidewheel plate (F) to bottom center of each
door. (See Figure 5)
Figure 6
7. Adjust height and alignment of doors by turning the pendant
bolts. (See Figure 7)
8. After adjustment is complete, replace the washers and
locking screws. (See Figure 7)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CM6DH SERIES
Installation Instructions
8
From Dimmer Module
7
Figure 7
IR Sensor Placement
Figure 8
The placement of the IR sensor can be crucial to proper
operation of the system. A flexible IR sensor is provided to
make it easier to achieve reliable operation.
System Activation
1. Insert plug from the power supply into the jack on the top of
the motor box.
In most applications, the IR sensor may be installed on top of
the cabinet. However, tall and/or dark colored ceilings can
absorb the IR signal. If inconsistent operation is encountered
there are two alternatives.
Top of
Cabinet
24VDC Input
•
One, the flexible IR sensor eye can be placed so
that it gives the sensor "line of sight" to the signal
from the remote controller. Often this merely
involves placing the IR sensor so that it peeks up
over the top of the cabinet. It doesn't have to be
much, just enough to give "line of sight".
•
Two, an IR sensor extension cord can be used to
position the IR sensor in the cabinet near to the
other remote controlled units. (For example, near
to the VCR or DVD player)
Install Light Dimmer Module (Optional)
With the dimmer option installed cabinet lighting can be
switched on or off or dimmed using the left buttons on the
systems remote control.
To install the optional dimmer:
Front of
Cabinet
1. Plug 115VAC lighting into the back of the Light Dimmer
Module.
2. Plug the other end of Dimmer Module cord into a 115VAC
grounded receptacle on motor assembly.
Figure 9
2. Plug Powercord into 115VAC outlet.
CAUTION: The Dimmer is for 120 volt incandescent or
Halogen lamps of at least 25 watts and should not to exceed
300 watts total.
IMPORTANT ! : A quality surge protection device is
recommended.
3. Make sure nothing is obstructing movement of doors,
The system also provides the option of creating and saving two
different lighting "scenes". Please refer to the Remote Control
instructions for information on how to configure "scenes".
4. Press and release the Activator Button on the front of the
Motor Box or the "Close Door button on the Remote Control.
(The doors should travel to the fully closed position)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM6DH SERIES
Activator
Activator Button
Figure 10
Figure 12
5. Press the "Open Door" button on the Remote Control.
The controller will then be in “Learn Mode” (The door will move
for 3 seconds, stop for 10 seconds, and when it starts moving
again it will be in it’s “Learn Mode”).
NOTE: If a different travel distance is required see "Door Travel
Adjustment below.
When put into “Learn Mode” the mechanism runs back and
forth several times and measures it’s environment, such as
open and closed locations etc., and then stops and remembers
these learned measurements, so that next time the system runs
it knows where to start and stop.
ADJUSTMENTS
Adjust Door Travel Distance
To adjust door travel distance:
1. Press and hold the activator button on the front of the motor
box for 13 seconds.
Status Light Codes
There is a light on the front of the mechanism motor box that
will tell through its pattern of flashes and colors what the
mechanism is doing.
The Status Light on the front of the motor box will begin to blink
alternately red and green. When this starts to happen release
the Activator Button. When put into "Learn Moden the system
runs back and forth several times and measures its
environment, such as open and closed locations etc. The
system will then stop and remember these learned
measurements.
Status Indicator
Activator
Figure 13
Normal Doors At Rest - The Status Light will be on steady
green.
Figure 11
Normal Run Motion of Doors - The Status Light will flash in
groups of 2 green followed by a pause. In normal run motion
the doors on the system have a variable speed. The doors will
start slowly, accelerate to a fast speed, and then slow down
before coming to a stop.
System Controls and Indicators
Learn Mode
The CM6DH system has no limit switches. The system uses an
encoder on the motor to collect data and send it to the micro
processor’s memory. The software "learns" about its
environment (speed, time duration, stop points, etc.) during the
initial setup of the unit and retains that information until
requested to "relearn" its environment.
Doors Obstructed - The Status Light will flash in groups of 3
red followed by a pause. If the doors meet an obstruction they
will sense the obstruction, stop momentarily, and move in the
opposite direction for a few seconds. ---- Remove the
obstruction and then activate the doors. They should return to
normal run motion.
The unit is shipped pre-set from the factory and will then
continually adjusts to it’s enviornment on each activation.
Doors Obstructed Both Ways - The Status Light will flash in
groups of 4 red followed by a pause. Similar to Doors
Obstructed but doors are prevented from moving in either
direction. ---- Remove the obstruction and then activate the
doors. They should return to normal run motion.
If for some reason you want to place the system into “Learn
Mode” (such as to stop at other than its normal stop points),
Press and hold the red activator button on the front of the motor
box for approxamatly 13 seconds and then release it when the
Status Light flashes quickly red, green, red, green, red, green.
Travel Too Far - The Status Light will flash in groups of 5 red
followed by a pause. The motor is running but the doors are
not moving. ---- Has the motor box been uncoupled from the
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CM6DH SERIES
Installation Instructions
Control Input on Front of Motor Box
track, or is the motor box bent, causing it to become uncoupled
from the track?
Power Loss - The Status Light will be on solid red. ---- There
has been a power loss (due to an electrical storm, etc.). When
next activated the doors will move at a slow speed to their full
closed position. If the doors are already closed they will not
move. The Status Light will return to solid green and the doors
are ready for normal activation.
Control Input
Optional Control Input Connections
Control Input- 8 position RJ 45 modular phone jack
Discrete control for use with 3rd party control.
Figure 14
•
•
Position 8- Open
Position 7- Stop
IR Receiver “Eye” input for Eubank, Inc. supplied external IR
reciever only.
NOTE: Making a momentary dry contact closure between the
common and the open, closed, stop, or sequence will
activate the system in that mode.
•
•
Position 6 - V out
Position 5 - Vcc, 5v
Radio Power for external RF receiver only.
Position 4 - 24 VDC
Sequence control for use with 3rd party control.
•
•
•
Position 3 - Sequence- Open, Stop, Close, Stop
Position 2 - Common
Discrete control for use with 3rd party control.
•
Position 1 - Close
Control Input on Front of Motor Box
Figure 15
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM6DH SERIES
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CM6DH SERIES
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Asia Pacific
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
8820-000022 RevA
¤2007 Chief Manufacturing
11/07
D
24F
䂀⧂ゑを⚘処⼦㧠䤍D 24⚗F 枅掌⦌棔⮶☵ 㪚
P
F
+86-755-8996 9226
+86-755-8996 9217
Download from Www.Somanuals.com. All Manuals Search And Download.
|