Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
ITEM 69231
7″ PORTABLE WET CUTTING
TILE SAW
Email our technical support at: [email protected]
REV 12a
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-800-444-3353 as soon as possible.
©
®
Copyright 2011 by Harbor Freight Tools . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Download from Www.Somanuals.com. All Manuals Search And Download.
General Tool Safety Warnings (cont.)
13. DON’T OVERREACH. Keep proper
Table A: RECOMMENDED MINIMUM WIRE GAUGE
FOR EXTENSION CORDS
footing and balance at all times.
(120 VOLT)
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
EXTENSION CORD
LENGTH
NAMEPLATE
AMPERES
(at full load)
25′
50′ 100′ 150′
15. DISCONNECT TOOLS before servicing;
when changing accessories, such as
blades, bits, cutters, and the like.
0 – 6
18
18
16
14
16
16
16
12
16
14
14
14
12
12
6.1 – 10
10.1 – 12
12.1 – 16
16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in
off position before plugging in.
Do not use.
9. USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Table A shows the correct size to use depending
on cord length and nameplate ampere rating.
If in doubt, use the next heavier gauge.
17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.
18. NEVER STAND ON TOOL. Serious injury
could occur if the tool is tipped or if the
cutting tool is unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function – check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
The smaller the gauge number, the heavier the cord.
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings, bracelets,
or other jewelry which may get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
20. DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of
rotation of the blade or cutter only.
12. SECURE WORK. Use clamps or a vise to hold
work when practical. It’s safer than using your
hand and it frees both hands to operate tool.
21. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool
until it comes to a complete stop.
Item 69231
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Instructions
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION
READ AND FOLLOW THESE INSTRUCTIONS:
110-120 V~ Grounded Tools: Tools with Three Prong Plugs
1. In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
6. Repair or replace damaged or worn cord immediately.
Grounding
Pin
2. Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.
Figure A: 125 V~ 3-Prong Plug and Outlet
(for up to 125 V~ and up to 15 A)
3. Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow
stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
7. This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated above
in Figure A: 125 V~ 3-Prong Plug and Outlet.
The tool has a grounding plug
that looks like the plug illustrated above in
Figure A: 125 V~ 3-Prong Plug and Outlet.
4. Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as
to whether the tool is properly grounded.
8. The outlet must be properly installed and grounded
in accordance with all codes and ordinances.
9. Do not use an adapter to connect
this tool to a different outlet.
5. Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.
Tilesaw Safety Warnings
1. For Your Own Safety Read Instruction
9. Make sure the workpiece is supported at all
times while sawing. Use a roller stand (not
provided) with larger workpieces if necessary.
Manual Before Operating Saw
2. Wear eye protection.
10. To properly understand all safety warnings, be familiar
with the following safety terms and equipment:
3. Use saw-blade guard and spreader
for every operation for which it can be
used, including all through sawing.
a. Featherboard – A block with “fingers” that hold
the workpiece against the fence while sawing.
4. Keep hands out of the line of saw blade.
5. Use an appropriate push-stick when required.
6. Know how to reduce risk of kickback.
7. Do not perform any operation freehand.
8. Never reach around or over saw blade.
b. Through-sawing – A cut made from one side of
a tile to the opposite side, without stopping.
c. Push-stick – A narrow strip of wood or other soft
material with a notch cut into one end and which
is used to push short pieces of material through
saws. It provides a safe distance between the
hands and the cutting tool. Must be narrower than
the cut width to prevent contact with the blade.
Page 4
For technical questions, please call 1-800-444-3353.
Item 69231
Download from Www.Somanuals.com. All Manuals Search And Download.
Tilesaw Safety Warnings (cont.)
d. Freehand – Feeding a workpiece through the
saw without using a fence or guided support
to guide it. NOT A SAFE METHOD.
12. Check the guard for proper operation with
saw disconnected from power before each
use. Do not disable any guard. Do not
operate saw if any movable guard does not
move freely and close instantly. Make sure
any movable guard does not touch the blade
in all angles, depths of cut, and positions.
e. Kerf – The gap made by the saw in the workpiece.
f. Kickback – A sudden reaction to a pinched,
bound, or misaligned blade, causing
an uncontrolled workpiece to lift up and
out of the saw toward the operator.
13. Keep the guard in place while through-
sawing. Verify that the spreader lines up
with the blade to prevent binding.
g. Spreader – A metal plate that follows the
saw blade to keep the kerf (gap) from closing
on the saw blade. Spreaders, except riving
knives, must be aligned to the blade after
blade adjustment to prevent binding.
14. Construct an appropriate Push Stick out of wood
according to the guidelines on the following page.
15. DO NOT OPERATE WITH ANY GUARD DISABLED,
DAMAGED, OR REMOVED. Moving guards
must move freely and close instantly.
h. Riving Knife – A spreader mounted on the
same mechanism as the blade. Generally
more effective than simple spreaders.
16. The use of accessories or attachments not
recommended by the manufacturer may
result in a risk of injury to persons.
11. As noted previously, Kickback is a sudden reaction
to a pinched, bound, or misaligned blade, causing an
uncontrolled workpiece to lift up and out of the saw
toward the operator.
17. When servicing use only identical replacement parts.
Kickback is usually a result of tool misuse and can be
limited or avoided by following the precautions below:
18. Only use safety equipment that has been approved
by an appropriate standards agency. Unapproved
safety equipment may not provide adequate
• Fence must be completely
parallel to the saw blade.
protection. Eye protection must be ANSI-approved
and breathing protection must be NIOSH-approved
for the specific hazards in the work area.
• Workpiece must be free from flaws and from
foreign objects (such as nails and screws).
• Support large workpieces along their
entire length. Large workpieces tend
to bend, grabbing the blade.
19. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
• Do not use a dull or damaged blade.
• Maintain control of the workpiece. Do not
allow the workpiece to rest against the
moving blade without holding onto it.
20. Industrial applications must follow OSHA guidelines.
• If the blade binds or a cut is interrupted, turn
off the power switch and hold the workpiece
still until the blade stops. Correct the cause
of blade binding before proceeding.
21. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
• Before continuing an unfinished cut, center
the blade in the pre-cut kerf and check that
the saw teeth are not engaged into the
workpiece before turning on the saw.
22. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
• Push the workpiece past the
blade prior to release.
23. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
Item 69231
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Essential Straight Push-stick
Features and Functions
Handle Notch
Note: Straight style (traditional) stick shown. A different stick
design may be used if it properly protects against all hazards.
Diagram not to scale.
• Must be far
enough down
the stick to allow
a comfortable
and firm grip.
• Push sticks must be made from sturdy, defect-free,
plywood or normal wood to prevent unexpected
breakage. Material must be at least 1/4″ thick,
but no thicker than the finished wood.
• Must be deep
enough to prevent
hand from slipping
down the stick.
• Inspect push stick before use and do not use
a damaged or deteriorated push stick.
• Push stick dimensions will vary depending
• Do not cut more than
halfway into the stick
to prevent weakening.
on the application and user.
• Corners may
be rounded to
increase comfort.
Stick Length
• Must be long enough
to keep hand
clear of blade.
• At least 6″ from end
of handle to closest
part of notch.
90°
Notch
• Must be right (90°) angle, cut at 30°-40° from the angle
of the stick to keep hands out of the line of the blade.
30°-40°
• The lower lip of the notch must be no
longer than the workpiece is thick.
Page 6
For technical questions, please call 1-800-444-3353.
Item 69231
Download from Www.Somanuals.com. All Manuals Search And Download.
POSITION OF TILE SAW
EXTENSION CORDS
4. Use only extension cords that are intended for
outdoor use. These extension cords are identified
by a marking “Acceptable for use with outdoor
tools; store indoors while not in use.” Use only
extension cords having an electrical rating not
less than the rating of the product. Do not use
damaged extension cords. Examine extension
cord before using and replace if damaged.
Do not abuse extension cords and do not yank
on any cord to disconnect. Keep cord away
from heat and sharp edges. Always disconnect
the extension cord from the receptacle before
disconnecting the product from the extension cord.
Tile Saw
Power Cord
5. WARNING – To reduce the risk of electrocution,
keep all connections dry and off the ground.
Do not touch plug with wet hands.
Drip Loop
6. Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s)
to be used for the tile saw. Receptacles are
available having built-in GFCI protection and
may be used for this measure of safety.
Figure B: Drip Loop
1. To avoid the possibility of the tool plug or
receptacle getting wet, position tile saw to one
side of a wall mounted receptacle to prevent
water from dripping onto the receptacle or plug.
The user should arrange a “drip loop” in the cord
connecting the saw to a receptacle. The “drip loop”
is that part of the cord below the level of the
receptacle, or the connector if an extension cord
is used, to prevent water traveling along the cord
and coming in contact with the receptacle.
7. WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities, contains chemicals known [to the State
of California] to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other
masonry products
• Arsenic and chromium from
chemically treated lumber
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
2. If the plug or receptacle does get wet, DON’T unplug
the cord. Disconnect the fuse or circuit breaker
that supplies power to the tool. Then unplug and
examine for presence of water in the receptacle.
Tile Saw
8. WARNING: Handling the cord on this product will
expose you to lead, a chemical known to the State
of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
Power Cord
Extension
Cord
Drip Loop
9. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
Figure C: Extension Cord Drip Loop
3. If an extension cord is used, the drip loop must be
before the cord connection and the extension cord
connection must be placed on an elevated surface.
Item 69231
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Vibration Safety
This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent
physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an extended period should first be examined by
a doctor and then have regular medical check-ups to ensure medical problems are not being
caused or worsened from use. Pregnant women or people who have impaired blood circulation
to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers), seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces the blood supply to the hands
and fingers, increasing the risk of vibration-related injury.
3. Use tools with the lowest vibration when there is a choice between different processes.
4. Include vibration-free periods each day of work.
5. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool do the work.
6. To reduce vibration, maintain the tool as explained in this manual. If
any abnormal vibration occurs, stop use immediately.
SAVE THESE INSTRUCTIONS.
Page 8
For technical questions, please call 1-800-444-3353.
Item 69231
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Electrical Rating
Motor No Load Speed
Arbor Size
120V~ / 60Hz / 4.8A
3,550 RPM
5/8"
Max. Accessory Diameter 7"
Bevel Cut
0-45°
1" @ 90°
3/5" @ 45°
Maximum Depth of Cut
Blade Type
Diamond, continuous rim (sold separately)
184892
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool to its “OFF” position, remove the Safety Lock and unplug the
tool from its electrical outlet before assembling or making any adjustments to the tool.
Note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Functions
Upper Blade
Miter Guide
Guard (2)
(40)
Table Top (7)
Rip Fence (12)
Saw Blade (26)
(under Upper Guard)
Lower Blade
Guard (23)
Water Tray (57)
Safety Lock
Power Switch (56)
Bevel Lock Knob (39)
(additional Bevel Lock Knob
on other side of saw)
Angle Gauge
Figure D
Item 69231
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Tool Set Up
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool to its “OFF” position, remove the Safety Lock and unplug the
tool from its electrical outlet before assembling or making any adjustments to the tool.
TO PREVENT SERIOUS INJURY:
DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED.
Moving guards must move freely and close instantly.
Installing the Blade (blade sold separately)
1. Unthread the two Screws holding the Lower Blade Guard in place. Remove the Screws, Washers and
Lower Blade Guard.
Outer Flange
Inner Flange
2. Slide the Hex Wrench onto
the Hex Nut and the Slotted
Wrench onto the Spindle.
Hex Nut
Hex Wrench
3. Hold the Spindle in place with the
Slotted Wrench while unthreading
the Hex Nut with the Hex Wrench.
Spindle
4. Remove the Hex Nut, Outer
Flange and old blade (if in place).
Keep the Inner Flange in place.
Washer
5. Slide the new Blade and the
Outer Flange onto the Spindle.
Saw Blade
Slotted Wrench
6. Thread the Hex Nut onto
the Spindle and tighten in
place with the wrenches.
Screw
Lower Blade Guard
7. Replace the Lower Blade Guard and
secure in place with the Washers and
Screws.
Figure E
Installing/Adjusting the Rip Fence
Miter Guide
1. Place the Rip Fence on the Table
Top to the left of the Blade.
Rip Fence
2. Pull up on the Lock Lever, slide the Rip Fence to the
desired location, then press the Lock Lever down to lock the
Rip Fence in place on the Table Top.
Lock
Lever
Figure F
Page 10
For technical questions, please call 1-800-444-3353.
Item 69231
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning the Miter Guide
Place the Miter Guide against the Rip Fence.
Work Piece and Work Area Set Up
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
3. Make sure that the Base is on a steady level
work surface so the water level of the tank can
be accurately measured and maintained.
2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard
or exposing the power cord to possible damage.
The power cord must reach the work area with
enough extra length to allow for a drip loop.
4. There must not be objects, such as utility lines,
nearby that will present a hazard while working.
5. Keep workpieces pressed firmly against
the Table and Fence while cutting.
6. Mark cut lines using waterproof marker or crayon.
General Operating Instructions
1. Install the Blade and check that the Upper
and Lower Blade Gaurds are in place.
2. Fill the Water Tray to the Maximum Fill
line on the sides of the Tray and slide it
under the Lower Blade Guard, raising
the tool slightly to allow the Water Tray
to fit. Check that the water level is
Lower
Blade
Guard
between the MIN and MAX on the Lower
Blade Guard and adjust if needed.
MAX
CAUTION: Do not operate the Tile
Saw with too little or too much water in
the Water Tank. Keep the water level
between the minimum and maximum level
markings on the Lower Blade Guard.
MIN
Water Tray
Figure G
Item 69231
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. For Straight/Miter Cuts:
a. Install the Rip Fence on the Table Top
with or without the Miter Gauge.
b. Place the workpiece on the Table and firmly
against the Miter Gauge and/or Rip Fence.
c. Make sure the workpiece is clear of the Blade,
then dry your hands, plug in the Saw, insert the
Safety Lock and turn the Power Switch ON.
d. Let the Blade build up to full speed before cutting.
e. Hold the material firmly against the Rip Fence
and feed the material into the Blade.
f. When the cut is made, turn the Saw OFF.
Wait for the Blade to come to a complete stop
before removing any part of the workpiece.
Figure H: Straight Cuts
4. For Bevel Cuts:
a. Adjust the location of the Rip Fence if needed.
b. Loosen the two Bevel Lock Knobs on the front and back
of the table Base and tilt the table to the desired angle.
c. Tighten the Bevel Lock Knobs to secure the Table Top.
d. Place the workpiece against the Miter
Gauge and/or Rip Fence.
e. Make sure the workpiece is clear of the Blade,
then dry your hands, plug in the Saw, insert the
Safety Lock and turn the Power Switch ON.
f. Let the Blade build up to full speed before cutting.
g. Hold the material steadily against the Rip Fence
and feed the material into the Blade.
h. When the cut is made, turn the Saw OFF.
Wait for the Blade to come to a complete stop
before removing any part of the workpiece.
Figure I: Bevel Cuts
5. To prevent accidents, turn off the tool, remove the Safety Lock,
and disconnect its power supply after use. Lift the tool slightly and
slide out the Water Tray. Empty the Water Tray, clean out silt and
mud. Clean, then store the tool indoors out of children’s reach.
Page 12
For technical questions, please call 1-800-444-3353.
Item 69231
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool to its “OFF” position, remove the Safety Lock and unplug the tool
from its electrical outlet before performing any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general condition
of the tool. Check for loose hardware, misalignment
or binding of moving parts, cracked or broken
parts, damaged electrical wiring, and any other
condition that may affect its safe operation.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.
3.
WARNING! If the supply cord of this
power tool is damaged, it must be replaced
only by a qualified service technician.
Troubleshooting
Problem
Tool will not start. 1. Cord not connected.
Possible Causes
Likely Solutions
1. Check that cord is plugged in.
2. No power at outlet.
2. Check power at outlet. If outlet is unpowered, turn off tool
and check circuit breaker. If breaker is tripped, make sure
circuit is right capacity for tool and circuit has no other loads.
3. Tool’s thermal reset breaker
tripped (if equipped).
3. Turn off tool and allow to cool. Press reset button on tool.
4. Internal damage or wear. (Carbon
brushes or switch, for example.)
4. Have technician service tool.
Tool operates
slowly.
Extension cord too long or
wire size too small.
Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for its
length and load. See Table A on page 3.
Performance
decreases
over time.
1. Accessory dull or damaged.
1. Keep cutting accessories sharp. Replace as needed.
2. Have qualified technician replace brushes.
2. Carbon brushes worn or damaged.
Excessive noise
or rattling.
1. Belt (if equipped) too loose (slipping)
or too tight (bearing damage).
1. Properly tension belt.
2. Internal damage or wear. (Carbon
brushes or bearings, for example.)
2. Have technician service tool.
Overheating.
1. Forcing machine to work too fast.
2. Accessory misaligned.
1. Allow machine to work at its own rate.
2. Check and correct accessory to fence
and/or table alignment.
3. Accessory dull or damaged.
4. Blocked motor housing vents.
3. Keep cutting accessories sharp. Replace as needed.
4. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while blowing
dust out of motor using compressed air.
5. Motor being strained by long or
small diameter extension cord.
5. Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for its
length and load. See Table A on page 3.
Follow all safety precautions whenever diagnosing or servicing
the tool. Disconnect power supply before service.
Item 69231
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List and Diagram
Part
Description
Qty
1
1
1
1
2
1
1
1
1
1
1
1
6
7
2
1
1
1
1
1
2
8
1
1
1
1
1
5
1
Part
Description
Qty
1
1
2
4
1
2
2
2
2
1
1
2
2
1
2
2
2
6
1
1
1
1
2
1
2
1
1
1
1
1
2
3
4
5
6
7
8
9
Hex Nut M5
31 Lock Press Plate
Upper Blade Guard
Bracket
32 Housing
33 Cross Sunk Head Screw (M4 x 10)
34 Foot
35 Big Flat Washer 5
36 Nylon Locknut M6
37 Hex Bolt M6 x 12
38 Big Flat Washer 6
39 Bevel Lock Knob
40 Miter Guide
41 Carry Handle
42 Cross Head Screw M5 x 10
43 Wire Clamp
44 Seal Ring
45 Star Washer
46 Ground Terminal Plate
47 Spring Washer 4
48 Cross Head Screw
49 Motor
50 Rear Cover
51 Strain Relief
52 Cord & Plug
53 Cross Head Self-Tapping Screw
54 Switch Plate
55 Cross Head Screw
56 Power Switch
57 Water Tray
Warning Label
Roll Pin
Bevel Lock Knob
Table Top
Moving Paw
Compressing Spring
10 Square Washer,A
11 Carriage Bolt
12 Rip Fence
13 Flat Washer 5
14 Spring Washer 5
15 Hex Bolt M5 x 10
16 Fix Paw
17 Rubber Washer
18 Big Flat Washer 8
19 Connection Bolt
20 Lock Lever
21 Cross Head Screw M4 x 16
22 Flat Washer 4
23 Lower Blade Guard
24 Hex Nut M12 x 1.5
25 Outer Flange
27 Inner Flange
28 Inner Blade Guard
29 Cross Head Screw M5 x 12
30 Protection Plate
58 Slotted Wrench
59 Hex Wrench A
1
2
3
4
5
40
6
7
50
22
48
15
14
13
41
12
42
43
44
16
33
17
18
19
5
49
20
32
31
48
45
47
46
54
43
51
30
52
11
13
8
14
28
9
10
35
14
29
29
36
37
27
53
34
38
39
22
23
25
55
57
24
56
59
58
22
21
Page 14
For technical questions, please call 1-800-444-3353.
Item 69231
Download from Www.Somanuals.com. All Manuals Search And Download.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Item 69231
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
|