Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
ITEM 69454
7"
anglE grIndEr
Email our technical support at: [email protected]
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-800-444-3353 as soon as possible.
©
®
Copyright 2012 by Harbor Freight Tools . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SaVE thiS manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical safety
1. power tool plugs must match the outlet.
never modify the plug in any way.
4. Do not abuse the cord. never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
Do not use any adapter plugs with grounded
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
2. avoid body contact with grounded surfaces
such as pipes, radiators, ranges and
5. When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use
refrigerators. There is an increased risk of
electric shock if your body is grounded.
reduces the risk of electric shock.
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
6. if operating a power tool in a damp location
is unavoidable, use a Ground Fault Circuit
interrupter (GFCi) protected supply.
Use of a GFCI reduces the risk of electric shock.
personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication. A moment of inattention while operating
power tools may result in serious personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
2. use safety equipment. always wear eye
protection. Safety equipment such as
dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate
conditions will reduce personal injuries.
7. if devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust-related hazards.
3. prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energizing power
tools that have the switch on invites accidents.
8. Only use safety equipment that has been
approved by an appropriate standards agency.
Unapproved safety equipment may not provide
adequate protection. Eye protection must
be ANSI-approved and breathing
protection must be NIOSH-approved for
the specific hazards in the work area.
4. Remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
Item 69454
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
power tool use and care
1. Do not force the power tool. use the
correct power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
5. maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. if damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
2. Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
6. Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
3. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
7. use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
Service
have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
Page 4
For technical questions, please call 1-800-444-3353.
Item 69454
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Warnings Common for Grinding, Sanding, Wire Brushing,
polishing, or abrasive Cutting-Off Operations
1. this power tool is intended to function
as a grinder, sander, wire brush, polisher
or cut-off tool. Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool.
workpiece fragments. the eye protection must
be capable of stopping flying debris generated
by various operations. The eye protection must
be capable of stopping flying debris generated by
various operations. The dust mask or respirator
must be capable of filtering out particles generated
by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2. Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because the
accessory can be attached to your power tool,
it does not assure safe operation.
8. Keep bystanders a safe distance away from work
area. anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
3. the rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their RATED SPEED can break and fly apart.
9. hold power tool by insulated gripping surfaces
only, when performing an operation where
the accessory may contact hidden wiring
or its own cord. An accessory contacting a
″live″ wire may make exposed metal parts of
the power tool ″live″ and shock the operator.
4. the outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
10. position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or
snagged and your hand or arm may be
5. the arbor size of wheels, flanges, backing
pads or any other accessory must properly
fit the spindle of the power tool. Accessories
with arbor holes that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
pulled into the spinning accessory.
11. never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the surface
and pull the power tool out of your control.
6. Do not use a damaged accessory.
Before each use inspect the accessory such
as abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess wear,
wire brush for loose or cracked wires. if power
tool or accessory is dropped, inspect for
damage or install an undamaged accessory.
after inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run
the power tool at maximum no-load speed
for one minute. Damaged accessories will
normally break apart during this test time.
12. Do not run the power tool while carrying
it at your side. Accidental contact with the
spinning accessory could snag your clothing,
pulling the accessory into your body.
13. Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside
the housing and excessive accumulation of
powdered metal may cause electrical hazards.
14. Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
15. Do not use accessories that require liquid
coolants. Using water or other liquid coolants
may result in electrocution or shock.
7. Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. as appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
Item 69454
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
16. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
23. WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities, contains chemicals known [to the State
of California] to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
Harbor Freight Tools for a replacement.
17. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
• Lead from lead-based paints
• Crystalline silica from bricks and cement or
other masonry products
• Arsenic and chromium from
18. Do not depress the spindle lock when
starting or during operation.
chemically treated lumber
19. Do not leave the tool unattended when it is plugged
into an electrical outlet. Turn off the tool, and
unplug it from its electrical outlet before leaving.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
20. Use clamps (not included) or other practical
ways to secure and support the workpiece to
a stable platform. Holding the work by hand
or against your body is unstable and may
lead to loss of control and personal injury.
24. WARNING: Handling the cord on this product will
expose you to lead, a chemical known to the State
of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
21. This product is not a toy.
Keep it out of reach of children.
22. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
In addition, people with pacemakers should:
• Avoid operating alone.
25. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
• Do not use with power switch locked on.
• Properly maintain and inspect
to avoid electrical shock.
• Properly ground power cord. Ground Fault Circuit
Interrupter (GFCI) should also be implemented
– it prevents sustained electrical shock.
Page 6
For technical questions, please call 1-800-444-3353.
Item 69454
Download from Www.Somanuals.com. All Manuals Search And Download.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush
or any other accessory. Pinching or snagging
causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power
tool to be forced in the direction opposite of the
accessory’s rotation at the point of the binding.
2. never place your hand near the rotating
accessory. Accessory may kickback over your hand.
3. Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to
the wheel’s movement at the point of snagging.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward
or away from the operator, depending on direction
of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
4. use special care when working corners, sharp
edges etc. avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
5. Do not attach a saw chain woodcarving
blade or toothed saw blade. Such blades
create frequent kickback and loss of control.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.
1. maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The operator can control torque reactions or
kickback forces, if proper precautions are taken.
Safety Warnings Specific for Grinding and
abrasive Cutting-off Operations
1. use only wheel types that are recommended
for your power tool and the specific
4. always use undamaged wheel flanges that are of
correct size and shape for your selected wheel.
Proper wheel flanges support the wheel thus reducing
the possibility of wheel breakage. Flanges for cut-off
wheels may be different from grinding wheel flanges.
guard designed for the selected wheel.
Wheels for which the power tool was not designed
cannot be adequately guarded and are unsafe.
2. the guard must be securely attached
to the power tool and positioned for
5. Do not use worn down wheels from larger
power tools. Wheel intended for larger
power tool is not suitable for the higher
speed of a smaller tool and may burst.
maximum safety, so the least amount of
wheel is exposed towards the operator.
The guard helps to protect operator from broken
wheel fragments and accidental contact with wheel.
6. Dress appropriately. Wear leather leggings and
fire resistant footwear during use. Do not wear pants
with cuffs, shirts with open pockets, or any clothing
that can catch and hold molten metal or sparks.
3. Wheels must be used only for recommended
applications. For example: do not grind with
the side of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side forces
applied to these wheels may cause them to shatter.
Item 69454
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Warnings Specific for abrasive Cutting-off Operations
1. Do not “jam” the cut-off wheel or apply
excessive pressure. Do not attempt to make
an excessive depth of cut. Overstressing the
wheel increases the loading and susceptibility
to twisting or binding of the wheel in the cut and
the possibility of kickback or wheel breakage.
4. Do not restart the cutting operation in
the workpiece. let the wheel reach full
speed and carefully reenter the cut.
The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
5. Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece
near the line of cut and near the edge of the
workpiece on both sides of the wheel.
2. Do not position your body in line with and
behind the rotating wheel. When the wheel,
at the point of operation, is moving away from
your body, the possible kickback may propel the
spinning wheel and the power tool directly at you.
3. When wheel is binding or when interrupting a
cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. never attempt
to remove the cut-off wheel from the cut while
the wheel is in motion otherwise kickback
may occur. Investigate and take corrective
6. use extra caution when making a “pocket cut”
into existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
action to eliminate the cause of wheel binding.
Safety Warnings Specific for Sanding Operations
Do not use excessively oversized sanding disc paper. Follow manufacturer’s recommendations
when selecting sanding paper. Larger sanding paper extending beyond the sanding pad
presents a laceration hazard and may cause snagging, tearing of the disc or kickback.
Safety Warnings Specific for polishing Operations
Do not allow any loose portion of the polishing bonnet or its attachment strings
to spin freely. tuck away or trim any loose attachment strings. Loose and spinning
attachment strings can entangle your fingers or snag on the workpiece.
Safety Warnings Specific for Wire Brushing Operations
1. Be aware that wire bristles are thrown by
the brush even during ordinary operation.
Do not overstress the wires by applying
excessive load to the brush. The wire bristles
can easily penetrate light clothing and/or skin.
2. if the use of a guard is recommended for
wire brushing, do not allow any interference
of the wire wheel or brush with the guard.
Wire wheel or brush may expand in diameter
due to work load and centrifugal forces.
Page 8
For technical questions, please call 1-800-444-3353.
Item 69454
Download from Www.Somanuals.com. All Manuals Search And Download.
Vibration Safety
This tool vibrates during use. Repeated or long-term
exposure to vibration may cause temporary or permanent
physical injury, particularly to the hands, arms and
shoulders. To reduce the risk of vibration-related injury:
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check-ups
to ensure medical problems are not being caused
or worsened from use. Pregnant women or
people who have impaired blood circulation to
the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
4. Use tools with the lowest vibration when there
is a choice between different processes.
5. Include vibration-free periods each day of work.
6. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.
7. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
SaVE thESE inStRuCtiOnS.
Item 69454
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding
tO pREVEnt ElECtRiC ShOCK anD DEath FROm
inCORRECt GROunDinG WiRE COnnECtiOn:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
Do not modify the power cord plug provided with the tool. never remove the grounding prong from
the plug. Do not use the tool if the power cord or plug is damaged. if damaged, have it repaired by a service
facility before use. if the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
Grounded tools: tools with three prong plugs
2. The grounding prong in the plug is connected through
the green wire inside the cord to the grounding
system in the tool. The green wire in the cord must
be the only wire connected to the tool’s grounding
system and must never be attached to an electrically
“live” terminal. (See 3-prong plug and Outlet.)
3. The tool must be plugged into an appropriate outlet,
properly installed and grounded in accordance with
all codes and ordinances. The plug and outlet should
look like those in the preceding illustration.
3-prong plug and Outlet
(See 3-prong plug and Outlet.)
1. Tools marked with “Grounding Required” have a three
wire cord and three prong grounding plug. The plug
must be connected to a properly grounded outlet.
If the tool should electrically malfunction or break
down, grounding provides a low resistance path to
carry electricity away from the user, reducing the risk
of electric shock. (See 3-prong plug and Outlet.)
Double insulated tools: tools with two prong plugs
1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies OSHA
requirements and complies with the applicable
standards of Underwriters Laboratories, Inc.,
the Canadian Standard Association,
and the National Electrical Code.
2. Double insulated tools may be used in either of the
120 volt outlets shown in the preceding illustration.
(See Outlets for 2-prong plug.)
Outlets for 2-prong plug
Page 10
For technical questions, please call 1-800-444-3353.
Item 69454
Download from Www.Somanuals.com. All Manuals Search And Download.
Extension Cords
1. Grounded tools require a three wire extension cord.
Double Insulated tools can use either
7. Make sure the extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired
by a qualified electrician before using it.
a two or three wire extension cord.
2. As the distance from the supply outlet increases,
you must use a heavier gauge extension cord.
Using extension cords with inadequately sized wire
causes a serious drop in voltage, resulting in loss of
power and possible tool damage. (See table a.)
8. Protect the extension cords from sharp objects,
excessive heat, and damp or wet areas.
RECOmmEnDED minimum WiRE GauGE
FOR EXtEnSiOn CORDS* (120/240 VOlt)
3. The smaller the gauge number of the wire, the
greater the capacity of the cord. For example,
a 14 gauge cord can carry a higher current
than a 16 gauge cord. (See table a.)
EXtEnSiOn CORD
namEplatE
lEnGth
ampERES
(at full load)
25′ 50′ 75′ 100′ 150′
4. When using more than one extension cord to make
up the total length, make sure each cord contains at
least the minimum wire size required. (See table a.)
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5. If you are using one extension cord for more
than one tool, add the nameplate amperes
and use the sum to determine the required
minimum cord size. (See table a.)
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
6. If you are using an extension cord outdoors, make
sure it is marked with the suffix “W-A” (“W” in
-
-
* Based on limiting the line volt-
age drop to five volts at 150% of
the rated amperes.
Canada) to indicate it is acceptable for outdoor use.
taBlE a
Symbology
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Read the manual before
set-up and/or use.
WARNING marking concerning
Risk of Hearing Loss.
Wear hearing protection.
Volts Alternating Current
V~
a
WARNING marking
concerning Risk of Fire.
Do not cover ventilation ducts.
Keep flammable objects away.
WARNING marking concerning
Risk of Electric Shock.
Amperes
No Load Revolutions per Minute (RPM)
n xxxx/min.
0
Properly connect power cord
to appropriate outlet.
Item 69454
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Electrical Rating
120V~ / 60Hz / 11A
7800 RPM
Motor No Load Speed
Max. Accessory Diameter
7″ (178 mm)
Max. Accessory Thickness 1/4" (6mm)
7/8"
Arbor Hole Diameter
Using included adapter
Spindle Thread
5/8″ x 11 TPI
Setup - Before use:
Read the EntiRE impORtant SaFEtY inFORmatiOn section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
tO pREVEnt SERiOuS injuRY FROm aCCiDEntal OpERatiOn:
turn the power Switch of the tool off and unplug the tool from its electrical
outlet before assembling or making any adjustments to the tool.
note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
aSSEmBlY
installing the Wheel Guard
tO pREVEnt SERiOuS injuRY: Do not operate this tool without the Wheel Guard properly installed.
Wheel
Guard
Nut
1. Loosen the Wheel Guard Nut.
2. Slide the collar of the Wheel Guard
over the rim of the Gear Housing.
Collar
Wheel Guard
3. Rotate the Wheel Guard as needed to
shield you during the planned work.
4. Tighten the Wheel Guard Nut securely.
5. Check the Wheel Guard to ensure it is firmly in place.
Gear
Housing
Adjust if necessary before proceeding.
Figure a
Page 12
For technical questions, please call 1-800-444-3353.
Item 69454
Download from Www.Somanuals.com. All Manuals Search And Download.
installing the auxiliary handle
tO pREVEnt SERiOuS injuRY:
Do not operate this tool with one hand only or without the auxiliary handle properly installed.
Auxiliary Handle
1. The Auxiliary Handle may be installed
in one of three positions, on either side
or on top of the Gear Housing.
Alternate locations
2. Screw the threaded end of the
Auxiliary Handle into the selected position.
Tighten securely before beginning work.
Figure B
Functions
Indicator Light
Lock ON Button
Auxiliary Handle
Spindle Lock
Blade
Trigger
Guard
Figure C
Item 69454
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating instructions
Read the EntiRE impORtant SaFEtY inFORmatiOn section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
tool Set up
tO pREVEnt SERiOuS injuRY FROm aCCiDEntal OpERatiOn:
turn the power Switch of the tool off and unplug the tool from its
electrical outlet before installing accessories.
installing a non-threaded Grinding Wheel
1. The Grinding Wheel MUST be:
• rated to at least 7800 RPM.
c. Rotate the wheel 90° and repeat the test
until the entire wheel has been checked.
• no larger than 7″ (178 mm) in diameter.
• fitted with a 7/8” round arbor hole.
• 1/4” (6mm) thick or less.
• suitable for surface grinding, not edge grinding.
• dry and clean.
d. An undamaged wheel will give a clear tone.
If cracked, there will be a dead sound
and not a clear ring.
5. For wheels with paper gaskets (blotters) or
metal gaskets: Slip the grinding wheel onto the
Spindle with the gasket first. The gasket should be
centered on the grinding wheel and the wheel and
gasket should rest flat against the Inner Flange.
• proven undamaged by inspection and
by the ring-test explained below.
2. Press in and hold the Spindle Lock Button
to prevent the Spindle from turning.
WaRninG: to prevent serious
injury, gaskets must be used for all
3. Remove the Outer Flange. Keep the
Inner Flange in position on the Spindle.
grinding wheels they are provided with.
Gaskets help prevent grinding wheel damage
and wheel slippage, causes of wheel failure.
4. Closely inspect the Grinding Wheel before mounting.
Perform a ring-test on the wheel (unless wheel is
smaller than 4″ or is an unusual shape) as follows:
6. Thread the Outer Flange onto the Spindle.
Wrench tighten only enough so that the wheel is
securely held on the spindle.
a. Suspend wheel using a dowel or
finger through the arbor hole.
WaRninG: to prevent serious injury,
do not overtighten flange. Overtightening can
damage the wheel, causing wheel failure.
45°
45°
hang
Wheel
from
V
E
R
t
i
C
a
l
Dowel
tap
Wheel
here
C
E
n
t
E
R
45°
45°
b. Tap the flat side of the wheel with a light non-
metallic object, such as a screwdriver handle,
at a point 45° from the vertical center line on
each side of the wheel and 1 – 2 inches from
the edge of the wheel (see Illustration).
Page 14
For technical questions, please call 1-800-444-3353.
Item 69454
Download from Www.Somanuals.com. All Manuals Search And Download.
installing a threaded accessory
tO pREVEnt injuRY: Wear heavy-duty work gloves when handling wire wheels and brushes.
these accessories are sharp and can cause injury.
1. The accessory MUST be:
• rated to at least 7800 RPM.
• no larger than 7″ (178 mm) in diameter.
• fitted with a threaded opening of 5/8″ x 11 TPI.
• undamaged.
• a sanding disc and backing pad,
a sanding flap disc, a wire wheel or
a wire cup brush (accessories not included).
2. Press in and hold the Spindle Lock Button
to prevent the Spindle from turning.
3. Remove the Outer Flange and the
Inner Flange and keep in a safe place.
Figure E
4. Thread disc accessory firmly onto the Spindle.
Wrench tighten onto the spindle.
Workpiece and Work area Set up
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
3. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be hazardous objects, such
as utility lines or foreign objects, nearby that
will present a hazard while working.
2. Route the power cord along a safe route
to reach the work area without creating a
tripping hazard or exposing the power cord to
possible damage. The power cord must
reach the work area with enough extra length
to allow free movement while working.
5. You must use personal safety equipment including,
but not limited to, ANSI-approved eye and hearing
protection, as well as heavy-duty work gloves.
6. Before beginning work, provide for sparks and
debris that will fly off the work surface.
General Operating instructions
tO pREVEnt SERiOuS injuRY: Grip the tool firmly in both hands.
1. Make sure that the Trigger is not
locked on, then plug in the tool.
5. To create a smoother surface,
keep the tool moving over the work surface.
2. Squeeze the Trigger to start the tool.
To lock the tool on, press the Lock ON
Button then release the Trigger.
6. Release the Trigger to stop the tool, or press and
release the Trigger if the Lock ON Button is engaged.
7. Allow the tool to come to a complete
stop before setting it down.
3. Allow the tool to come up to full speed
before touching the work material.
8. To prevent accidents, turn off the tool and
disconnect its power supply after use. Clean, then
store the tool indoors out of children’s reach.
4. Apply the wheel to the work material at a 10° – 15°
angle, allowing the tool to operate at full speed.
If the tool bogs down, use lighter pressure.
Item 69454
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
maintenance and Servicing
procedures not specifically explained in this manual must
be performed only by a qualified technician.
tO pREVEnt SERiOuS injuRY FROm aCCiDEntal OpERatiOn:
turn the power Switch of the tool off and unplug the tool from its electrical outlet
before performing any inspection, maintenance, or cleaning procedures.
tO pREVEnt SERiOuS injuRY FROm tOOl FailuRE:
Do not use damaged equipment. if abnormal noise or vibration occurs,
have the problem corrected before further use.
Cleaning, maintenance, and lubrication
1. BEFORE EaCh uSE, inspect the general
2. aFtER uSE, wipe external surfaces
condition of the tool. Check for:
of the tool with clean cloth.
• loose hardware,
3. Periodically blow dust and grit out of the motor vents
using dry compressed air. Wear ANSI-approved
safety goggles and NIOSH-approved
• misalignment or binding of moving parts,
• cracked or broken parts,
breathing protection while doing this.
• damaged electrical wiring, and
4.
WaRninG! if the supply cord of this
power tool is damaged, it must be replaced
only by a qualified service technician.
• any other condition that may
affect its safe operation.
accessory Storage and handling
1. Handle accessories carefully to prevent
dropping or bumping. Do not use wheels
that have been dropped or bumped.
2. Store accessories in shelves, racks, boxes, or
drawers. Storage area must be kept dry, and above
freezing. Any grinding or cut-off wheels exposed to
humidity or freezing temperatures must not be used.
Page 16
For technical questions, please call 1-800-444-3353.
Item 69454
Download from Www.Somanuals.com. All Manuals Search And Download.
troubleshooting
problem
Tool will not start.
possible Causes
1. Cord not connected.
likely Solutions
1. Check that cord is plugged in.
2. No power at outlet.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Tool’s thermal reset
3. Turn off tool and allow to cool.
Press reset button on tool.
breaker tripped (if equipped).
4. Internal damage or wear. (Carbon
brushes or switch, for example.)
4. Have technician service tool.
Tool operates slowly. 1. Excess pressure applied to workpiece. 1. Decrease pressure, allow tool to do the work.
2. Power being reduced by long or
small diameter extension cord.
2. Eliminate use of extension cord.
If an extension cord is needed, use one with
the proper diameter for its length and load.
See Extension Cords in GROUNDING section.
Have qualified technician replace brushes.
Performance
Carbon brushes worn or damaged.
decreases over time.
Excessive noise
or rattling.
Internal damage or wear.
(Carbon brushes or bearings, for example.)
1. Forcing tool to work too fast.
Have technician service tool.
Overheating.
1. Allow tool to work at its own rate.
2. Blocked motor housing vents.
2. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.
3. Motor being strained by long or
small diameter extension cord.
3. Eliminate use of extension cord.
If an extension cord is needed, use one with
the proper diameter for its length and load.
See Extension Cords in GROUNDING section.
1. Be sure disc accessory arbor is correct
and Outer Flange/Arbor Nut is tight.
Tool does not
grind, sand or
brush effectively.
1. Disc accessory may be
loose on Spindle.
2. Disc accessory may be damaged,
worn or wrong type for the material.
2. Check condition and type of disc accessory.
Use only proper type of disc
accessory in good condition.
Follow all safety precautions whenever diagnosing or servicing
the tool. Disconnect power supply before service.
Item 69454
For technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
parts list and Diagram
plEaSE REaD thE FOllOWinG CaREFullY
THe MANUFACTUReR AND/oR DISTRIBUToR HAS PRovIDeD THe PARTS LIST AND ASSeMBLy DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING oUT oF HIS oR HeR RePAIRS To THe oRIGINAL PRoDUCT oR RePLACeMeNT PARTS
THeReTo, oR ARISING oUT oF HIS oR HeR INSTALLATIoN oF RePLACeMeNT PARTS THeReTo.
parts list
part
1
2
3
4
5
6
7
8
Description
Qty
1
1
1
1
1
1
1
1
4
4
4
1
2
1
7
1
1
1
1
1
4
1
1
1
1
1
1
1
1
part
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
Description
Qty
1
2
1
1
1
1
1
1
1
2
1
2
2
2
1
1
1
1
2
1
1
1
1
1
1
5
1
1
Outer Flange
Rotor
Grinding Wheel
Inner Flange
Wheel Guard
Screw St4.8x60
Air Baffle Plate
Stator
Bearing 608
Bearing Sleeve
Housing
Bolt M8x30
Nut M8
Spindle
Half Round Key 4X5xφ13
Screw M5x14
Spring Washer 5
Flat Washer 5
Front Cover
Bearing 6201
Bearing Retaining Plate
Screw M4x10
Nameplate
9
Side Cover (right)
Screw St2.9x10
Rear Cover (right)
Brush Holder
Disc Spring
Carbon Brush
Rear Cover (left)
Side Cover (left)
Power Cord
Cable Sleeve
Screw St4.2x14
Cable Pressplate
Right Handle
Trigger
Power Indicator-Lamp
Indicator-Lamp Cover
Left Handle
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Big Gear
Wave Washer Φ12
Circlip For Shaft Φ12
Circlip Φ5
Needle Bearing Hk081410
Screw St4.8x25
Gear Box
Spindle Lock Spring
Spindle Lock
Auxiliary Handle
Aulminium Sleeve
Nut M8
Screw St4.2x16
Pin Wrench
Small Gear
Bearing Retaining Plate
Hex Key
Record product’s Serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Page 18
For technical questions, please call 1-800-444-3353.
Item 69454
Download from Www.Somanuals.com. All Manuals Search And Download.
assembly Diagram
Item 69454
For technical questions, please call 1-800-444-3353.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS ExPRESSLY IN LIEU OF ALL OTHER
WARRANTIeS, eXPReSS oR IMPLIeD, INCLUDING THe WARRANTIeS oF MeRCHANTABILITy AND FITNeSS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
|