Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
ITEM 68987
Email our technical support at: [email protected]
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-800-444-3353 as soon as possible.
©
®
Copyright 2011 by Harbor Freight Tools . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SaVE thiS manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical safety
1. power tool plugs must match the
outlet. never modify the plug in any way.
Do not use any adapter plugs with grounded
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
4. Do not abuse the cord. never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
2. avoid body contact with grounded surfaces
such as pipes, radiators, ranges and
5. When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use
refrigerators. There is an increased risk of
electric shock if your body is grounded.
reduces the risk of electric shock.
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
6. if operating a power tool in a damp location
is unavoidable, use a Ground Fault circuit
interrupter (GFci) protected supply. Use of
a GFCI reduces the risk of electric shock.
personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication. A moment of inattention while operating
power tools may result in serious personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
2. use safety equipment. always wear eye
protection. Safety equipment such as
dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate
conditions will reduce personal injuries.
7. if devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust-related hazards.
3. prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energizing power
tools that have the switch on invites accidents.
8. Only use safety equipment that has been
approved by an appropriate standards agency.
Unapproved safety equipment may not provide
adequate protection. Eye protection must
be ANSI-approved and breathing
protection must be NIOSH-approved for
the specific hazards in the work area.
4. Remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
Item 68987
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
power tool use and care
1. Do not force the power tool. use the
correct power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
5. maintain power tools. check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. if damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
2. Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
3. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
7. use the power tool, accessories and blades
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
Service
have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Biscuit plate Joiner Safety Warnings
7. When using a handheld power tool,
maintain a firm grip on the tool with
both hands to resist starting torque.
1.
DanGER: Keep hands away from cutting
area and the blade. Keep your second hand on
auxiliary handle, or motor housing. If both hands
are holding the saw, they cannot be cut by the blade.
8. Do not depress the spindle lock when
starting or during operation.
2. Disc cutters must be rated for at least the speed
recommended on the tool. Disc cutters running
over rated speed can fly apart and cause injury.
9. Do not leave the tool unattended when it is
plugged into an electrical outlet. Turn off the tool,
and unplug it from its electrical outlet before leaving.
3. always use the guard. The guard protects the
operator from broken disc cutter fragments and
unintentional contact with the disc cutter.
10. this product is not a toy.
Keep it out of reach of children.
4. maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
11. never hold piece being cut in your hands
or across your leg. Secure the workpiece
to a stable platform. It is important to
Harbor Freight Tools for a replacement.
support the work properly to minimize body
exposure, blade binding, or loss of control.
5. avoid unintentional starting.
Prepare to begin work before turning on the tool.
12. always use blades with correct size and
shape (diamond versus round) of arbor holes.
Blades that do not match the mounting hardware of
the saw will run eccentrically, causing loss of control.
6. Do not lay the tool down until it has come to
a complete stop. Moving parts can grab the
surface and pull the tool out of your control.
Page 4
For technical questions, please call 1-800-444-3353.
Item 68987
Download from Www.Somanuals.com. All Manuals Search And Download.
Biscuit plate Joiner Biscuit plate Joiner Safety Warnings (cont.)
13. never use damaged or incorrect blade
washers or bolt. The blade washers and
bolt were specially designed for your saw, for
optimum performance and safety of operation.
20. WaRninG: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities, contains chemicals known [to the State
of california] to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
14. Do not use dull or damaged blades.
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other
masonry products
15. Blades must be rated to at least the
maximum speed marked on the tool.
• Arsenic and chromium from
chemically treated lumber
16. maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
Harbor Freight Tools for a replacement.
17. Do not leave the tool unattended when it is
plugged into an electrical outlet. Turn off the tool,
and unplug it from its electrical outlet before leaving.
18. use clamps (not included) or other practical ways
to secure and support the workpiece to a stable
platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
21. WaRninG: handling the cord on this product
will expose you to lead, a chemical known
to the State of california to cause cancer,
and birth defects or other reproductive
harm. Wash hands after handling. (California
Health & Safety Code § 25249.5, et seq.)
19. people with pacemakers should consult their
physician(s) before use. Electromagnetic fields
in close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure. In
addition, people with pacemakers should:
• Avoid operating alone.
22. the warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
• Do not use with power switch locked on.
• Properly maintain and inspect to avoid
electrical shock.
• Any power cord must be properly grounded.
Ground Fault Circuit Interrupter (GFCI)
should also be implemented – it prevents
sustained electrical shock.
Vibration Safety
This tool vibrates during use. Repeated or long-term
exposure to vibration may cause temporary or permanent
physical injury, particularly to the hands, arms and
shoulders. To reduce the risk of vibration-related injury:
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
1. anyone using vibrating tools regularly or for
an extended period should first be examined
by a doctor and then have regular medical
check-ups to ensure medical problems are
not being caused or worsened from use.
Pregnant women or people who have impaired
blood circulation to the hand, past hand injuries,
nervous system disorders, diabetes, or Raynaud’s
Disease should not use this tool. If you feel any
medical or physical symptoms related to vibration
(such as tingling, numbness, and white or blue
fingers), seek medical advice as soon as possible.
vibration effects on the user.
4. use tools with the lowest vibration
when there is a choice.
5. include vibration-free periods each day of work.
6. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.
7. to reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
SaVE thESE inStRuctiOnS.
Item 68987
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Biscuit plate Joiner Safety Warnings (cont.)
Grounding
tO pREVEnt ElEctRic ShOcK anD DEath FROm
incORREct GROunDinG WiRE cOnnEctiOn:
check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
Do not modify the power cord plug provided with the tool. never remove the grounding prong from
the plug. Do not use the tool if the power cord or plug is damaged. if damaged, have it repaired by a service
facility before use. if the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
Grounded tools: tools with three prong plugs
2. The grounding prong in the plug is connected through
the green wire inside the cord to the grounding
system in the tool. The green wire in the cord must
be the only wire connected to the tool’s grounding
system and must never be attached to an electrically
“live” terminal. (See 3-prong plug and Outlet.)
3. The tool must be plugged into an appropriate outlet,
properly installed and grounded in accordance with
all codes and ordinances. The plug and outlet should
look like those in the preceding illustration.
3-prong plug and Outlet
(See 3-prong plug and Outlet.)
1. Tools marked with “Grounding Required” have a three
wire cord and three prong grounding plug. The plug
must be connected to a properly grounded outlet.
If the tool should electrically malfunction or break
down, grounding provides a low resistance path to
carry electricity away from the user, reducing the risk
of electric shock. (See 3-prong plug and Outlet.)
Double insulated tools: tools with two prong plugs
1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies OSHA
requirements and complies with the applicable
standards of Underwriters Laboratories, Inc.,
the Canadian Standard Association,
and the National Electrical Code.
2. Double insulated tools may be used in either of the
120 volt outlets shown in the preceding illustration.
(See Outlets for 2-prong plug.)
Outlets for 2-prong plug
Page 6
For technical questions, please call 1-800-444-3353.
Item 68987
Download from Www.Somanuals.com. All Manuals Search And Download.
Biscuit plate Joiner Safety Warnings (cont.)
Extension cords
1. Grounded tools require a three wire extension cord.
Double Insulated tools can use either
7. Make sure the extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired
by a qualified electrician before using it.
a two or three wire extension cord.
2. As the distance from the supply outlet increases,
you must use a heavier gauge extension cord.
Using extension cords with inadequately sized wire
causes a serious drop in voltage, resulting in loss of
power and possible tool damage. (See table a.)
8. Protect the extension cords from sharp objects,
excessive heat, and damp or wet areas.
REcOmmEnDED minimum WiRE GauGE
FOR EXtEnSiOn cORDS* (120/240 VOlt)
3. The smaller the gauge number of the wire, the
greater the capacity of the cord. For example,
a 14 gauge cord can carry a higher current
than a 16 gauge cord. (See table a.)
EXtEnSiOn cORD
namEplatE
lEnGth
ampERES
(at full load)
25′ 50′ 75′ 100′ 150′
4. When using more than one extension cord to make
up the total length, make sure each cord contains at
least the minimum wire size required. (See table a.)
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5. If you are using one extension cord for more
than one tool, add the nameplate amperes
and use the sum to determine the required
minimum cord size. (See table a.)
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
6. If you are using an extension cord outdoors, make
sure it is marked with the suffix “W-A” (“W” in
-
-
* Based on limiting the line volt-
age drop to five volts at 150% of
the rated amperes.
Canada) to indicate it is acceptable for outdoor use.
taBlE a
Symbology
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Read the manual before
set-up and/or use.
WARNING marking concerning
Risk of Hearing Loss.
Wear hearing protection.
Volts Alternating Current
V~
a
WARNING marking
concerning Risk of Fire.
Do not cover ventilation ducts.
Keep flammable objects away.
WARNING marking concerning
Risk of Electric Shock.
Amperes
No Load Revolutions per Minute (RPM)
n xxxx/min.
0
Properly connect power cord
to appropriate outlet.
Item 68987
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Electrical Rating
Motor No Load Speed
Blade
120V~ / 60Hz / 8.5A
11,000 RPM
4″ Diameter (Item 38840)
7/8″ round
Arbor
note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Setup - Before use:
Read the EntiRE impORtant SaFEty inFORmatiOn section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
tO pREVEnt SERiOuS inJuRy FROm acciDEntal OpERatiOn:
turn the power Switch of the tool off and unplug the tool from its electrical outlet
before assembling or making any adjustments to the tool.
note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Functions
Handle (23)
Angle Locking Knob (84)
Spindle Lock
Angle Ruler (82)
Angle Fence (81)
Height Locking
Knob (74)
Cutting Guide
Trigger (29)
Trigger Lock
Dust Chute (85)
Depth Setting
Dial (65)
Depth Adjustment
Bolt (55)
Page 8
For technical questions, please call 1-800-444-3353.
Item 68987
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating instructions
Read the EntiRE impORtant SaFEty inFORmatiOn section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
tool Set up
tO pREVEnt SERiOuS inJuRy FROm acciDEntal OpERatiOn:
turn the power Switch of the tool off and unplug the tool from its electrical outlet
before adjusting the tool or installing accessories.
make sure that all guards are in place and in proper working order and
that all adjustment knobs are tight before operation.
changing Blades
1. Remove the four Screws and the Base
Plate on the bottom of the unit.
Base Plate
2. While pressing in on the Spindle Lock Button on the
top of the unit, use the Spanner Wrench to loosen
(counterclockwise) and remove the Outer Flange
and Blade. Do not remove the Inner Flange. Note the
direction of the blade teeth when removing the Blade.
Outer Flange
Blade
3. Place a new Blade and the Outer Flange onto
the Spindle making sure the blade teeth are
facing the correct direction and the flat side
of the Outer Flange is facing outward.
Spanner Wrench
4. Press and hold the Spindle Lock Button
and use the Spanner Wrench to tighten
(clockwise) the Blade in place.
Figure 1
5. Replace the Base Plate and secure
in place with the four Screws.
attaching the Dust Bag
2. If the bag is not already attached to the Dust
Chute, squeeze together the wire brace
ends on the Dust Bag and slide the Bag
onto the Dust Chute. Release the wires.
1. Align the Dust Chute with the Dust
Port and slide it in place.
3. To empty the bag, unzip the Zipper at the large end
of the bag and empty contents. Zip bag closed.
Item 68987
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the cutting Depth
The Depth Adjustment Dial sets the cutting depth
of the blade. The Dial has settings for three sizes
of biscuits (0, 10 or 20), and an “M” setting which
is the maximum depth that the tool can cut.
To check the setting for your biscuit
size do either of the following:
a. Make a sample cut in a scrap piece of
wood and check that the biscuit will fit.
To set the tool for a biscuit size:
b. Being careful of the blade, depress
the Fence as far as it will go, then
measure how far the blade extends.
Rotate the Depth Adjustment Dial to the desired
setting for the biscuit size you will be using.
Press and
hold Fence
Depth Adjustment Dial
Figure 2
Figure 3
Measure Blade
To adjust the cutting depth:
Nut
Depth
Bolt
Figure 4
a. Loosen the Nut on the Depth Bolt, then thread
the bolt in or out. Adjusting the Bolt closer to
the Depth Adjustment Dial makes a shallower
cut, while farther away will make a deeper cut.
b. Depress the Fence and measure how far
the Blade extends. Once the desired setting
is reached, tighten the Nut in place.
Page 10
For technical questions, please call 1-800-444-3353.
Item 68987
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Fence angle
To adjust the fence angle to anywhere from 0º to 90º:
Angle Locking Knob
1. Loosen the Angle Locking Knob and
rotate the Angle Fence until the desired
angle is set on the Angle Ruler.
2. Tighten the Angle Locking Knob.
Angle Ruler
Figure 5
Setting the height
The Height fence setting is to measure the cut from
the top surface of the workpiece. It is set using
both the Angle Fence and the Height Fence.
Height Locking
Knob
1. Set the Angle Fence to 90º (see above,
Setting the Fence Angle).
2. Loosen the Height Locking Knob and
raise or lower the Fence Assembly.
3. Tighten the Height Locking Knob.
Figure 6
Work piece and Work area Set up
1. Work piece selection:
3. Route the power cord along a safe route
to reach the work area without creating a
tripping hazard or exposing the power cord
to possible damage. The power cord must
reach the work area with enough extra length
to allow free movement while working.
a. Work piece must be free of foreign
objects and loose knots.
b. Wet lumber, green (unseasoned) lumber,
and pressure treated lumber all have an
increased potential for kickback and should
only be cut with a blade designed for cutting
that lumber. Wear a NIOSH-approved
respirator and have appropriate ventilation
whenever cutting pressure treated lumber.
4. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
5. Verify that there are no utility lines or
hardware in or near the workpiece.
This is especially critical for plunge cuts.
2. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
Item 68987
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
General Operating instructions
locking trigger
1. Secure the piece in place with the
cutting mark facing up.
The Biscuit Joiner has a safety lock mechanism to
prevent accidentally turning the unit on. You can
either turn the tool on and lock it on, or turn it on so
that it only stays on while the Trigger is depressed.
2. Adjust the tool to the desired cutting
depth, angle and height.
3. Plug the Biscuit Joiner into a
grounded 120V~, 60Hz outlet.
Trigger
Trigger Lock
4. Align the cutting guide on the Fence with
the cutting mark on the workpiece.
5. Turn on the tool and wait for the
Blade to reach full speed.
Figure 7
6. Press into the workpiece to make the cut.
To turn the tool on without locking it, press and
hold the Trigger while pushing forward then
releasing the Trigger Lock. Continue to depress
the Trigger as long as you want it powered.
Release the Trigger to turn the power off.
7. When the cut is complete, slide the tool out of
the finished slot and release the Trigger.
8. To prevent accidents, turn off the tool and
disconnect its power supply after use. Clean, then
store the tool indoors out of children’s reach.
To lock the tool on, press and hold the Trigger while
pressing forward on the Trigger Lock. Release the
Trigger, then release the Trigger Lock. The Biscuit
Joiner will stay on without depressing the Trigger.
Press and release the Trigger to turn the unit off.
note: For efficient dust pickup, empty
the Dust Bag frequently.
to make a cut:
Operating tips
Before cutting your workpiece, make a test cut on scraps of wood, and fit them together to ensure the cut is
the correct size, depth and location. Adjust the cutting depth as needed (See Setting the Cutting Depth).
This Joiner is set up to cut slots for 3 different sizes of biscuits. Use the largest size biscuit that will fit your
operation, usually a workpiece 1/2" thick or larger will use the largest size biscuit (size #20).
Biscuit Sizes for this Joiner
1"
(23 mm)
3/4"
(19 mm)
5/8"
(15 mm)
#20
#10
#0
Figure 8
Page 12
For technical questions, please call 1-800-444-3353.
Item 68987
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating tips (cont.)
typical types of Joints
Miter Joints
T-Joints
Joining
Butt Joints
Edge-to-Edge
Cuts
Figure 9
Plan the biscuit slot at a point at least 2-1/2" from the outer edge of the board. Allow at least 1" between
slots in multiple plate applications for best results. Mark all slots on both boards at the same time to assure
proper alignment.
Ends of
Face of wood
wood
Figure 10
Figure 11
1. Begin with the Joiner base cutting into the end of the
wood, rather than the face as illustrated below.
3. Otherwise, mark the center line of each cut
individually.
4. Adjust the fences to the angle and depth
needed to make the cut (See Tool Set Up
section). Align center line on face plate with
the pencil mark on wood then make the cut.
Figure 11
2. If possible, lay the workpieces as they will be
joined together and mark a center line across
the join to mark the center of cut to be made.
Item 68987
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
maintenance and Servicing
procedures not specifically explained in this manual must
be performed only by a qualified technician.
tO pREVEnt SERiOuS inJuRy FROm acciDEntal OpERatiOn:
turn the power Switch of the tool off and unplug the tool from its electrical outlet
before performing any inspection, maintenance, or cleaning procedures.
tO pREVEnt SERiOuS inJuRy FROm tOOl FailuRE:
Do not use damaged equipment. if abnormal noise or vibration
occurs, have the problem corrected before further use.
cleaning, maintenance, and lubrication
BEFORE Each uSE, inspect the general condition of the tool. Check for loose
screws, misalignment or binding of moving parts, cracked or broken parts, damaged
electrical wiring, and any other condition that may affect its safe operation.
aFtER uSE:
1. Remove and empty the Dust Bag.
2. Wearing ANSI-approved safety glasses, use compressed air to blow saw
dust out of the tool vents and off the surface of the tool.
3. Wipe external surfaces of the tool with clean cloth.
4.
WaRninG! if the supply cord of this power tool is damaged, it
must be replaced only by a qualified service technician.
Page 14
For technical questions, please call 1-800-444-3353.
Item 68987
Download from Www.Somanuals.com. All Manuals Search And Download.
troubleshooting
problem
Tool will not start.
possible causes
1. Cord not connected.
likely Solutions
1. Check that cord is plugged in.
2. No power at outlet.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker. If breaker
is tripped, make sure circuit is right capacity
for tool and circuit has no other loads.
3. Tool’s thermal reset breaker
tripped (if equipped).
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Internal damage or
wear. (Carbon brushes or
switch, for example.)
4. Have technician service tool.
Tool operates slowly. Power being reduced by long or
small diameter extension cord.
Eliminate use of extension cord. If an extension
cord is needed, use one with the proper
diameter for its length and load. See Extension
Cords in GROUNDING section.
Performance
1. Blade dull or damaged.
1. Keep blade sharp. Replace as needed.
decreases over time.
2. Carbon brushes worn
2. Have qualified technician replace brushes.
or damaged.
Excessive noise
or rattling.
Overheating.
Internal damage or wear. (Carbon
brushes or bearings, for example.)
1. Forcing tool to work too fast.
Have technician service tool.
1. Allow tool to work at its own rate.
2. Blade dull or damaged.
2. Keep blade sharp. Replace as needed.
3. Blocked motor housing vents.
3. Wear ANSI-approved safety goggles and NIOSH-
approved dust mask/respirator while blowing
dust out of motor using compressed air.
4. Motor being strained by long or
small diameter extension cord.
4. Eliminate use of extension cord.
If an extension cord is needed, use one with
the proper diameter for its length and load.
See Extension Cords in GROUNDING section.
Follow all safety precautions whenever diagnosing or servicing
the tool. Disconnect power supply before service.
Item 68987
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
parts list and Diagram
plEaSE REaD thE FOllOWinG caREFully
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE
Any PARTS oF The PRoDuCT. In FACT, The MAnuFACTuReR AnD/oR DISTRIBuToR eXPReSSLy
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
parts list
part
Description
Qty
1
1
1
2
2
1
1
1
1
4
1
1
1
1
2
1
1
11
2
1
1
2
1
1
1
1
2
1
1
5
1
1
1
1
1
2
4
2
2
1
1
1
2
1
part
Description
Qty
1
1
1
1
1
1
1
2
1
1
1
1
4
1
2
1
1
1
1
1
1
1
4
2
1
1
2
1
1
1
1
1
1
2
1
1
2
1
1
1
1
1
2
2
1
2
3
4
5
6
7
8
9
Bearing Set
46 Spring Washer φ8
Bearing 60017
Armature
47 Nut M8
49 Fan Guide
Check Ring φ10
Screw M4x10
Bearing 60100
Spindle Lock Button
Spring
50 Spanner Wrench
51 Inner Flange
52 Blade
53 Outer Flange
54 Flat Screw M4X8
55 Depth Setting Bolt M4X25
56 Depth Base Block
57 Depth Slide Plate
58 Guide Bar 1
59 Screw M4X14
60 Guide Bar 2
61 Spring
62 Set Screw M4
63 Compressing Spring
64 Steel Ball φ3
65 Depth Adjustment Dial
66 Shoulder Screw M5X12
67 Slide Plate
Gear Box
10 Screw
11 Check Ring φ5
12 Bearing φ12Xφ8X10
13 Spring Washer φ10
14 Gear
15 Screw M4X12
16 Bearing 80201
17 Front Cap
18 Spring Washer φ4
19 Screw M4X14
20 Woodruff-Key 3X10
21 Spindle
22 Screw M6X14
23 Upper Handle
24 Handle(L)
68 Base Plate
69 Flat Screw M4X6
70 Screw M3X6
71 Depth Mark
25 Handle(R)
26 Cord Clamp
27 Screw ST4.2X13
28 Capacitor
29 Trigger
30 Screw ST4.2X16
31 Cord Plug
32 Cord Protector
33 Brush Cap (R)
34 Brush Cap(L)
35 Brush Spring
36 Label
37 Screw ST3.5X10
38 Brush
39 Brush Holder
40 Roller φ3X4.9
41 Housing
72 Support Stand Board
73 Allen Bolt M4X16
74 Height Locking Knob
75 Pressed Block
76 Height Fence
77 Depth Pointer
78 Screw M4X14
79 Angle Pointer
80 Dowel
81 Angle Fence
82 Angle Ruler
83 Sink Screw
84 Angle Locking Knob
85 Dust Port
86 Dust Chute
87 Dust Bag
88 Nut
89 Cap
90 Spring Washer 65Mn(φ4)
42 Stator
43 Screw M4X55
45 Pinion
Page 16
For technical questions, please call 1-800-444-3353.
Item 68987
Download from Www.Somanuals.com. All Manuals Search And Download.
assembly Diagram
Item 68987
For technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Record product’s Serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Page 18
For technical questions, please call 1-800-444-3353.
Item 68987
Download from Www.Somanuals.com. All Manuals Search And Download.
limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. ThIS WARRAnTy IS eXPReSSLy In LIeu oF ALL oTheR
WARRAnTIeS, eXPReSS oR IMPLIeD, InCLuDIng The WARRAnTIeS oF MeRChAnTABILITy AnD FITneSS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Item 68987
For technical questions, please call 1-800-444-3353.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
|