Char Broil Charcoal Grill 463460712 User Manual

PRODUCT GUIDE

MODEL 463460712

Classic C-45G5CB

IMPORTANT: Fill out the product record information below.

Serial Number

See rating label on grill for serial number.

Date Purchased

For support and to register your

grill, please visit us at

www.charbroil.com

If you have questions or need

assistance during assembly,

please call 1-800-241-7548.

08/17/11 • G438-001-120801

Printed in China

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

CAUTION

CALIFORNIA PROPOSITION 65

Using pots larger than 6 quarts in capacity could

exceed weight limit of the

side burner shelf

1. Combustion by-products produced when using

this product contain chemicals known to the State of

California to cause cancer, birth defects, and other

reproductive harm.

or side shelf,

resulting in failure

2. This product contains chemicals, including lead

and lead compounds, known to the State of

California to cause cancer, birth defects or other

reproductive harm.

of grill cart

components.

Wash your hands after handling this product.

Installation Safety Precautions

• Use grill, as purchased, only with LP (propane) gas and the

regulator/valve assembly supplied. If your grill is Dual Fuel ready,

a conversion kit must be purchased for use with natural gas.

• Grill installation must conform with local codes, or in their

absence of local codes, with either the National Fuel Gas

Code, ANSI Z223.1/ NFPA 54, Natural Gas and Propane

Installation Code, CSA B149.1, or Propane Storage and

Handling Code, B149.2.

• All electrical accessories (such as rotisserie) must be

electrically grounded in accordance with local codes, or

National Electrical Code, ANSI / NFPA 70 or Canadian

Electrical Code, CSA C22.1. Keep any electrical cords and/or

fuel supply hoses away from any hot surfaces.

• This grill is safety certified for use in the United States and/or

Canada only. Do not modify for use in any other location.

Modification will result in a safety hazard.

WARNING

Do not attempt to repair or alter the

hose/valve/regulator for any “assumed” defect. Any

modification to this assembly will void your warranty

and create the risk of a gas leak and fire. Use only

authorized replacement parts supplied by

manufacturer.

NOTE: DO NOT over tighten screws and

washers that come into contact with porcelain

coated surfaces. Over tightening may cause the

porcelain coating to crack and break, resulting in

exposed metal that will be prone to rust.

Download from Www.Somanuals.com. All Manuals Search And Download.

GRILLING GUIDE – Getting Started

Temperature - Convective Grills ONLY.

The temperature gauge in the hood of your new grill measures

air temperature. The air temperature inside your grill will never

be as hot as the temperature at the cooking surface.

First Time Use

Read your Assembly Manual and ensure the grill is put together

properly. Remove all Point-of-Purchase advertising material from

all grill surfaces before first use. We recommend operating your

grill on its highest setting for 15-20 minutes prior to your first use.

This aids in removing the oils used during manufacturing.

Note: Since 1995, all regulators (the part that attaches to the gas

tank to regulate the flow of gas) have included a safety feature

that restricts gas flow in the event of a gas leak. You can

inadvertently activate this safety feature without having a gas

leak. This typically occurs when you turn on the gas using the

grill control knob before you turn on the LP tank valve. If the gas

regulator safety feature activates, the grill will only reach

temperatures between 250°F and 300°F even with all burners on

the high setting.

Lava Rock / Briquettes

This gas grill has been designed, engineered, and tested to be

used with flame tamers or heat distribution plates to provide

more even heating, improve the cleaning process, and reduce

flare-ups. The addition of after market lava rocks, charcoal, or

briquettes of any type will cause poor combustion and increase

the likelihood of a grease fire, and is not recommended. Using

briquettes, lava rock, or charcoal in this grill will void your

warranty. For extra smoke flavor, we recommend using a

smoker box with wood chips.

Regulator

Coupling Nut

If your grill is not getting hotter than 250°F to 300°F these

steps should be taken first to reset the gas regulator safety

device:

1. Open the grill lid.

2. Turn off all knobs on the control panel in front.

3. Turn off the tank knob.

4. Disconnect the regulator from the LP tank.

5. Wait 30 seconds.

6. Reconnect the regulator to the LP tank.

7. Slowly open the LP tank knob all the way. Do not put

excessive force on the valve at the full open position to avoid

damaging the valve.

8. Turn on the appropriate control knob and light the grill per the

instructions on the control panel.

An illustration of this process is included in this Product Guide.

See Troubleshooting section for additional information.

Pre-Heating Your Grill

Just like your home oven, your grill should be pre-heated to

provide optimum performance. Pre-heat the grill on high for 10-

15 minutes – longer if weather conditions require. Please refer to

the lighting instructions inside the Product Guide if you have

questions about how to light your grill. A match-light chain and

hole is provided for your convenience.

Download from Www.Somanuals.com. All Manuals Search And Download.

Rotisserie Cooking

GRILLING GUIDE – Grilling 101

Rotisserie cooking is best for 'round' meat, such as large roasts,

whole poultry, and pork. It generally requires an accessory motor

and spit rod that allows the meat to be turned at a constant

speed. Rotisserie cooking is best done in front of a special

rotisserie burner, or utilizing an indirect cooking burner

arrangement. A pan can be placed underneath the meat to catch

grease and food drippings, and helps minimize clean-up.

Outdoor grilling is really quite simple. You'll succeed with

burgers, dogs, or steaks usually on your very first try. With

experience, you will learn how to work with your grill, creating

more imaginative meals all the time. This knowledge makes up

the art of grilling. Before you start grilling, organize your food

according to cooking technique and required cooking time, and

optimize the use of your grilling area.

Direct Cooking

Direct cooking involves grilling your meat directly over high heat.

It is perfect for searing steaks, chops, and other smaller pieces of

meat and vegetables that quickly make their way to the table.

Indirect Cooking

Indirect cooking utilizes select burners to circulate heat

throughout the grill, without direct contact between the meat and

the flame. The meat is placed over the burner that is 'off'. This

method is generally used to slow cook large cuts of meat and

poultry. A pan can be placed underneath the meat to catch

grease and food drippings, and helps minimize clean-up.

Food Safety

Food safety is a very important part of enjoying the outdoor

cooking experience. To keep food safe from harmful bacteria,

follow these four basic steps:

Clean: Wash hands, utensils, and surfaces with hot soapy water

before and after handling raw meat.

Separate: Separate raw meats from ready-to-eat foods to avoid

cross contamination. Use a clean platter and utensils when

removing cooked foods.

Cook: Cook meat and poultry thoroughly to kill bacteria. Use a

thermometer to ensure proper internal food temperatures.

Chill: Refrigerate prepared foods and leftovers promptly.

Download from Www.Somanuals.com. All Manuals Search And Download.

Wood Chips

GRILLING GUIDE – Tips & Tricks

For extra smoke flavor when grilling, try adding wood chips.

Soak the chips in water for approximately 30 minutes before

adding to a smoke box or pan. Place smoke box or pan on top of

the cooking grate above the flame. Turn grill on high until the

wood starts to smoke. Reduce heat to desired temperature for

cooking, and place food on cooking grate as desired. Close lid to

retain more smoke. Hardwood varieties that work particularly

well with grilled foods include Alder, Apple, Cherry, Grapevines,

Hickory, Mesquite, Oak, Rosemary and Sassafras.

Cooking on your new grill is a hands-on experience, and it is

recommended to remain outside with your grill while cooking.

Grilling can be affected by many external conditions. In cold

weather, you will need more heat to reach an ideal cooking

temperature, and grilling may take longer. The meat's internal

temperature and thickness can also affect cooking times. Cold

and thicker meats will take longer to cook.

Internal Meat Temperatures

Meat cooked on a grill often browns very fast on the outside.

Therefore, use a meat thermometer to ensure it has reached

safe internal temperatures.

USDA Recommended Safe Minimum

Internal Temperatures

145° F

Beef, Veal, Lamb, Steak, Roasts, & Whole Pork

(with a 3 minute rest time)

Skewers

145° F

160° F

165° F

Fish

Metal skewers should be flat, with long handles. Round skewers

allow food to roll when turned, so it may not cook as evenly. Use

metal skewers when cooking meat kabobs. Wooden skewers

should be soaked in water for an hour before use, and are best

used for quick cooking foods such as vegetables and fruits.

Beef, Veal, Lamb, and Pork - Ground

Egg Dishes

Turkey, Chicken &

Duck-Whole, Pieces &

Ground

Please refer to the USDA for complete, up-to-date information.

Our internal temperature chart is based on USDA standards for

meat doneness. Check it out at www.isitdoneyet.gov

Sauces

Sauces containing sugars and fats can cause flare-ups, and your

food may burn. In general, apply these sauces during the final

10 minutes of cooking. Keep in mind, use of excessive sauces

or glazes will also require extra cleaning afterwards.

Marinades and Rubs

To enhance the flavor of grilled foods, a liquid marinade or dry

rub can be used prior to cooking. Meat can be either soaked or

injected with liquid marinade up to 24 hours prior to grilling. Dry

rubs can be applied directly to the meat immediately before

grilling.

Utensils

Use tongs or a spatula to handle the food instead of a fork, and

don't turn the food too

often. Piercing the food

with a fork will release

juices that you want in

the meat, and may

cause flare-ups.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cooking surfaces: If a bristle brush is used to clean any of the

grill cooking surfaces, ensure no loose bristles remain on cooking

surfaces prior to grilling. It is not recommended to clean cooking

surfaces while grill is hot.

GRILLING GUIDE – Cleaning Your Grill

Why Clean?

We've all heard the saying 'An ounce of prevention is worth a

pound of cure'. This is great advice when it comes to keeping

your grill clean.

Storing Your Grill

• Clean cooking grates.

• Store grill in dry location.

Routine Care

• When LP cylinder is connected to grill, store outdoors in a well

ventilated space and out of reach of children.

• Cover grill if stored outdoors. Choose from a variety of grill

covers offered by manufacturer.

Periodic cleaning of this grill is necessary,

as grill fires can occur when grease and

food debris collect in the bottom of the grill.

After each use, remove any remaining

food particles from the cooking grate and

inside of the grill using a grill brush. Do

this after the grill has cooled down, yet is

still warm. It is much easier to clean food

particles while warmth is still present, than

after the food particles have completely

cooled and hardened. This grill is not

designed to be 'burned off' by closing the

lid and turning the burners on High for an

extended time. The excessive heat

generated can cause leftover grease to

catch fire, and can cause permanent

damage to your grill.

• Store grill indoors ONLY if LP cylinder is turned off,

disconnected, and removed from grill. Never store LP cylinder

indoors.

• When removing grill from storage, follow the 'Cleaning the

Burner Assembly' instructions in the Use and Care section of

the Product Guide.

General Cleaning

Plastic parts: Wash with warm soapy water and wipe dry. Do not

use abrasive cleaners, degreasers or a concentrated grill cleaner

on plastic parts. Damage to and failure of parts can result.

Porcelain surfaces: Because of glass-like composition, most

residue can be wiped away with baking soda/water solution or

glass cleaner. Use non-abrasive scouring powder for stubborn

stains.

Painted surfaces: Wash with mild detergent or non-abrasive

cleaner and warm water. Wipe dry with a soft non-abrasive cloth.

Critters

Spiders like to make their homes in the venturi tubes of grills.

These must be inspected and cleaned regularly to ensure there

are no blockages. Refer to the Use and Care portion of this

Product Guide for complete information.

Stainless steel surfaces: Stainless steel can rust under certain

conditions. This can be caused by environmental conditions

such as chlorine or salt water, or improper

cleaning tools such as wire or steel

wool. It can also discolor due to heat,

chemicals, or grease build-up. To

maintain your grill's high quality

appearance, wash with mild detergent

and warm water, or use a stainless

steel grill cleaner. Baked-on grease

deposits may require the use of an

abrasive plastic cleaning pad. Use only

in direction of brushed finish to avoid

damage. Do not use abrasive pad on

areas with graphics.

Download from Www.Somanuals.com. All Manuals Search And Download.

LP Cylinder

USE AND CARE

•The LP cylinder used with your grill must meet the

following requirements:

•Use LP cylinders only with these required measurements: 12"

(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.)

capacity maximum.

•LP cylinders must be constructed and marked in accordance

with specifications for LP cylinders of the U.S. Department of

Transportation (DOT) or for Canada, CAN/CSA-B339,

cylinders, spheres and tubes for transportation of dangerous

goods. Transport Canada (TC). See LP cylinder collar for

marking.

DANGER

• NEVER store a spare LP cylinder under or near

the appliance or in an enclosed area.

•LP cylinder valve must have:

•Type 1 outlet compatible with

regulator or grill.

•Safety relief valve.

•UL listed Overfill Protection

Device (OPD). This OPD safety

OPD Hand Wheel

feature is identified by a unique triangular hand wheel. Use

only LP cylinders equipped with this type of valve.

•LP cylinder must be arranged for vapor withdrawal and include

collar to protect LP cylinder valve. Always keep LP cylinders in

upright position during use, transit or storage.

• Never fill a cylinder beyond 80% full.

• An over filled or improperly stored cylinder is a

hazard due to possible gas release from the

safety relief valve. This could cause an intense

fire with risk of property damage, serious injury or

death.

• If you see, smell or hear gas escaping,

LP cylinder in upright position for vapor withdrawal

immediately get away from the LP

LP (Liquefied Petroleum Gas)

•LP gas is nontoxic, odorless and colorless when produced. For

Your Safety, LP gas has been given an odor (similar to rotten

cabbage) so that it can be smelled.

cylinder/appliance and call your fire department.

LP Cylinder Removal, Transport and Storage

•Turn OFF all control knobs and LP cylinder valve. Turn coupling

nut counterclockwise by hand only - do not use tools to

disconnect. Loosen cylinder screw beneath bottom shelf or

disconnect other retention means, then lift PL cylinder up and

and out of cart. Install safety cap onto LP cylinder valve.

Always use cap and strap supplied with valve.

•LP gas is highly flammable and may ignite unexpectedly when

mixed with air.

LP Cylinder Filling

•Use only licensed and experienced dealers.

•LP dealer must purge new cylinder before filling.

•Dealer should NEVER fill LP cylinder more than 80% of LP

cylinder volume. Volume of propane in cylinder will vary by

temperature.

Failure to use safety cap as directed may result in serious

personal injury and/or property damage.

LP Cylinder Valve

•A disconnected LP cylinder in

storage or being transported

•A frosty regulator indicates gas overfill. Immediately close LP

cylinder valve and call local LP gas dealer for assistance.

must have a safety cap installed (as shown).

Do not store an LP cylinder in enclosed spaces

such as a carport, garage, porch, covered

patio or other building. Never leave an LP cylinder

inside a vehicle which may become overheated

by the sun.

•Do not release liquid propane (LP) gas into the atmosphere.

This is a hazardous practice.

Safety

Cap

Retainer Strap

•To remove gas from LP cylinder, contact an LP dealer or call a

local fire department for assistance. Check the telephone

directory under “Gas Companies” for nearest certified LP

dealers.

•Do not store an LP cylinder in an area where children play.

Download from Www.Somanuals.com. All Manuals Search And Download.

LP Cylinder Exchange

Connecting Regulator to the LP Cylinder

•Many retailers that sell grills offer you the option of replacing

your empty LP cylinder through an exchange service. Use only

those reputable exchange companies that inspect, precision fill,

test and certify their cylinders. Exchange your cylinder only

for an OPD safety feature-equipped cylinder as described

in the "LP Cylinder" section of this manual.

1.LP cylinder must be properly secured onto grill. (Refer to

assembly section.)

2.Turn all control knobs to the OFF position.

3.Turn LP cylinder OFF by turning hand-wheel clockwise to a

full stop.

•Always keep new and exchanged LP cylinders in upright

4.Remove the protective cap from LP cylinder valve. Always use

position during use, transit or storage.

cap and strap supplied with valve.

•Leak test new and exchanged LP cylinders BEFORE

connecting to grill.

•Place dust cap on cylinder valve outlet whenever the cylinder is

not in use. Only install the type of dust cap on the cylinder valve

outlet that is provided with the cylinder valve. Other types of caps

or plugs may result in leakage of propane.

OPD Hand Wheel

Type 1 outlet with

thread on outside

LP Cylinder Leak Test

For your safety

•Leak test must be repeated each time LP cylinder is exchanged

or refilled.

Safety Relief Valve

•Do not smoke during leak test.

•Do not use an open flame to check for gas leaks.

•Grill must be leak tested outdoors in a well-ventilated area,

away from ignition sources such as gas fired or electrical

appliances. During leak test, keep grill away from open flames

or sparks.

Strap and Cap

•Use a clean paintbrush and a 50/50 mild soap and water

solution. Brush soapy solution onto areas indicated by arrows

in figure below.

Do not use a POL transport plug

(plastic part with external threads)!

It will defeat the safety feature of

the valve.

Do not use household cleaning agents. Damage to gas

train components can result.

5.Hold regulator and insert nipple into LP

cylinder valve. Hand-tighten the

coupling nut, holding regulator in a

straight line with LP cylinder valve so

as not to cross-thread the connection.

Nipple has to be centered

into the LP cylinder valve.

WARNING

If “growing” bubbles appear do not use or move the LP

cylinder. Contact an LP gas supplier or your fire

department!

Download from Www.Somanuals.com. All Manuals Search And Download.

Leak Testing Valves, Hose and Regulator

1.Turn all grill control knobs to OFF.

2.Be sure regulator is tightly connected to LP cylinder.

3.Completely open LP cylinder valve by turning hand wheel

counterclockwise. If you hear a rushing sound, turn gas off

immediately. There is a major leak at the connection. Correct

before proceeding.

4.Brush soapy solution onto areas circled below, or other similar

fittings on your grill.

Hold coupling nut and regulator

as shown for proper connection

to LP cylinder valve.

6.Turn the coupling nut clockwise and tighten to a full stop. The

regulator will seal on the back-check feature in the LP cylinder

valve, resulting in some resistance. An additional one-half to

three-quarters turn is required to complete the

connection. Tighten by hand only – do not use tools.

NOTE:

If you cannot complete the connection, disconnect regulator and

repeat steps 5 and 6. If you are still unable to complete the

connection, do not use this regulator!

DANGER

• Do not insert any tool or foreign object into the valve

outlet or safety relief valve. You may damage the valve

and cause a leak. Leaking propane may result in

explosion, fire, severe personal injury, or death.

NOTE: Your grill

NOTE: Sideburner

shelf fascia not

may NOT be

equipped with a

sideburner.

shown for clarity.

WARNING

• Outdoor gas appliance is not intended to be installed

5.If “growing” bubbles appear, there is a leak. Close LP

cylinder valve immediately and retighten connections. If leaks

cannot be stopped do not try to repair. Call for replacement

parts.

in or on a boat.

• Outdoor gas appliance is not intended to be installed

in or on an RV.

• Never attempt to attach this grill to the self-contained

6.Always close LP cylinder valve after performing leak test by

LP gas system of a camper trailer or motor home.

turning hand wheel clockwise.

• Do not use grill until leak-tested.

• If a leak is detected at any time, STOP and call the fire

department.

• If you cannot stop a gas leak, immediately close

LP cylinder valve and call LP gas supplier or your fire

department!

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Tips

Before opening LP cylinder valve, check the coupling nut for

WARNING

tightness.

When grill is not in use, turn off all control knobs and LP

cylinder valve.

Never move grill while in operation or still hot.

Use long-handled barbecue utensils and oven mitts to avoid

burns and splatters.

Maximum load for sideburner and side shelf is 10 lbs.

For Safe Use of Your Grill and to Avoid Serious

Injury:

• Do not let children operate or play near grill.

• Keep grill area clear and free from materials that burn.

• Do not block holes in sides or back of grill.

• Check burner flames regularly.

• Use grill only in well-ventilated space. NEVER use in

enclosed space such as carport, garage, porch,

covered patio, or under an overhead structure of any

kind.

The grease tray or cup must be installed during use and

emptied after each use. Do not remove grease tray or cup

until grill has completely cooled.

Clean grill often, preferably after each cookout. If a bristle

brush is used to clean any of the grill cooking surfaces,

ensure no loose bristles remain on cooking surfaces prior to

grilling. It is not recommended to clean cooking surfaces

while grill is hot.

If you notice grease or other hot material dripping from grill

• Do not use charcoal or ceramic briquets in a gas grill.

onto valve, hose or regulator, turn off gas supply at once.

Determine the cause, correct it, then clean and inspect valve,

hose and regulator before continuing. Perform a leak test.

(Unless briquets are supplied with your grill.)

•

Do not cover grates with aluminum foil or any other

material. This will block burner ventilation and create

a potentially dangerous condition resulting in

property damage and/or personal injury.

Keep ventilation openings in cylinder enclosure (grill cart) free

and clear of debris.

Do not store objects or materials inside the grill cart

enclosure that would block the flow of combustion air to the

underside of either the control panel or the firebox bowl.

Use grill at least 3 ft. from any wall or surface.

Maintain 10 ft. clearance to objects that can catch fire

or sources of ignition such as pilot lights on water

heaters, live electrical appliances, etc.

The regulator may make a humming or whistling noise during

operation. This will not affect safety or use of grill.

If you have a grill problem see the "Troubleshooting Section".

If the regulator frosts, turn off grill and LP cylinder valve

immediately. This indicates a problem with the cylinder and it

should not be used on any product. Return to supplier!

CAUTION

• Putting out grease fires by closing the lid is not possible.

Grills are well ventilated for safety reasons.

• Do not use water on a grease fire. Personal injury may

result. If a grease fire develops, turn knobs and LP

cylinder off.

• Do not leave grill unattended while preheating or burning

off food residue on HI. If grill has not been regularly

cleaned, a grease fire can occur that may damage the

product. Follow instructions on General Grill Cleaning

and Cleaning The Burner Assembly to prevent grease fires.

• Apartment Dwellers:

Check with management to learn the requirements

and fire codes for using an LP gas grill in your

apartment complex. If allowed, use outside on the

ground floor with a three (3) foot clearance from walls

or rails. Do not use on or under balconies.

• NEVER attempt to light burner with lid closed. A

buildup of non-ignited gas inside a closed grill is

hazardous.

Ignitor Lighting

sDo not lean over grill while lighting.

1. Turn OFF gas burner control valves.

2. Turn ON gas at LP cylinder.

3. Open lid during lighting.

4. To ignite, push and turn ignition burner knob to HI.

5. P. ush and hold ELECTRONIC IGNITION button until the burner

lights.

6. If ignition does NOT occur in 5 seconds, turn the burner

controls OFF, wait 5 minutes and repeat the lighting

procedure.

• Never operate grill with LP cylinder out of correct

position specified in assembly instructions.

• Always close LP cylinder valve and remove

coupling nut before moving LP cylinder from

specified operation position.

7. To ignite remaining burners, turn knob to the HI position

starting with the burners closest to IGNITION BURNERS first.

If ignitor does not work, follow match lighting instructions.

Lighting instructions are continued on the next page

Download from Www.Somanuals.com. All Manuals Search And Download.

Burner Flame Check

Ignitor Lighting (continued)

• Remove cooking grates and flame tamers. Light burners, rotate

knobs from HI to LOW. You should see a smaller flame in

LOW position than seen on HI. Perform burner flame check

on sideburner, also. Always check flame prior to each use. If

only low flame is seen refer to "Sudden drop or low flame" in

the Troubleshooting Section.

8. For grills equipped with ELECTRONIC IGNITION at

each burner:

Repeat steps 4 through 6 to light each burner.

9. Once each burner has ignited, turn knobs to desired setting.

WARNING

Turn controls and gas source or tank OFF when not

in use.

LOW

Turning Grill Off

CAUTION

• Turn all knobs to the OFFposition. Turn LP cylinder OFF by turning

hand-wheel clockwise to a full stop.

If ignition does NOT occur in 5 seconds, turn the

burner controls OFF, wait 5 minutes and repeat the

lighting procedure. If the burner does not ignite with

the valve open, gas will continue to flow out of the

burner and could accidently ignite with risk of injury.

Ignitor Check

• Turn gas off at LP cylinder. Press and hold electronic ignitor

button. "Click" should be heard and spark seen each time

between each collector box or burner and electrode. See

"Troubleshooting" if no click or spark.

Valve Check

Match-Lighting

• Important: Make sure gas is off at LP cylinder before

checking valves. Knobs lock in OFF position. To check

valves, first push in knobs and release, knobs should spring

back. If knobs do not spring back, replace valve assembly

before using grill. Turn knobs to LOW position then turn back to

OFF position. Valves should turn smoothly.

Do not lean over grill while lighting.

1. Open lid. Turn ON gas at LP cylinder.

2. Place match into match holder (hanging from side panel of

grill). Light match; then light burner by placing match through

the match light hole on right or left side of grill.

Hose Check

3. Push in and turn far right or far left burner knob to the HI

position, depending on match light hole selected. Be sure

burner lights and stays lit.

• Before each use, check to see if hoses are cut or worn or kinked.

Replace damaged hoses before using grill. Use only

valve/hose/regulator specified by manufacturer.

General Grill Cleaning

4. Light adjacent burners in sequence by pushing knobs in and

turning to the HI position.

• Do not mistake brown or black accumulation of grease and

smoke for paint. Interiors of gas grills are not painted at the

factory (and should never be painted). Apply a strong solution

of detergent and water or use a grill cleaner with scrub brush

on insides of grill lid and bottom. Rinse and allow to completely

air dry. Do not apply a caustic grill/oven cleaner to painted

surfaces.

• Plastic parts: Wash with warm soapy water and wipe dry.

Do not use citrisol, abrasive cleaners, degreasers or a

concentrated grill cleaner on plastic parts. Damage to and

failure of parts can result.

NOTE: Your grill may NOT be equipped with a Sideburner!

Sideburner Ignitor Lighting

• Porcelain surfaces: Because of glass-like composition, most

residue can be wiped away with baking soda/water solution or

specially formulated cleaner. Use nonabrasive scouring powder

for stubborn stains.

Do not lean over grill while lighting.

1. Open sideburner lid. Turn ON gas at LP cylinder.

• Painted surfaces: Wash with mild detergent or nonabrasive

cleaner and warm soapy water. Wipe dry with a soft

nonabrasive cloth.

2. Turn sideburner knob to the HI position, push and hold

ELECTRONIC IGNITOR button.

3. If sideburner does NOT light within 5 seconds, turn knob to OFF,

wait 5 minutes, then

• Stainless steel surfaces: To maintain your grill’s high quality

appearance, wash with mild detergent and warm soapy water

and wipe dry with a soft cloth after each use. Baked-on grease

deposits may require the use of an abrasive plastic cleaning

pad. Use only in direction of brushed finish to avoid damage.

Do not use abrasive pad on areas with graphics.

• Cooking surfaces: If a bristle brush is used to clean any of

the grill cooking surfaces, ensure no loose bristles remain on

cooking surfaces prior to grilling. It is not recommended to

clean cooking surfaces while grill is hot.

repeat lighting procedure.

Sideburner Match Lighting

1. Open sideburner lid. Turn ON

gas at LP cylinder.

2. Place lit match near burner.

3. Turn sideburner knob to the

HI position.

Be sure burner lights and

stays lit.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Remove carryover tubes and burners.

Detach electrode from burner.

CAUTION

NOTE: Removal/Detachment method will depend on the

burner configuration. See different configurations in

illustrations below.

SPIDER ALERT!

5. Carefully lift each burner up and away from valve openings.

We suggest three ways to clean the burner tubes. Use the one

SPIDER AND WEBS

INSIDE BURNER TUBE

easiest for you.

(A) Bend a stiff wire (a light weight coat hanger works well)

into a small hook. Run the hook through each burner

tube several times.

(B) Use a narrow bottle brush with a flexible handle (do not

use a brass wire brush), run the brush through each

burner tube several times.

If you notice that your grill is getting hard to light or that the

flame isn’t as strong as it should be, take the time to check and

clean the venturi’s.

the burner tube and out the burner ports. Check each

port to make sure air comes out each hole.

6. Wire brush entire outer surface of burner to remove food

residue and dirt.

7. Clean any blocked ports with a stiff wire such as an open

paper clip.

VALVE

SPIDER WEBS

CONTROL PANEL

INSIDE VENTURI

8. Check burner for damage, due to normal wear and corrosion

some holes may become enlarged. If any large cracks or

holes are found replace burner.

BURNER

VERY IMPORTANT: Burner tubes must reengage valve

openings. See illustrations at right.

Correct

9. Attach electrode to burner.

burner-to-valve

In some areas of the country, spiders or small insects have been

known to create “flashback” problems. The spiders spin webs, build

nests and lay eggs in the grill’s venturi tube(s) obstructing the flow of

gas to the burner. The backed-up gas can ignite in the venturi behind

the control panel. This is known as a flashback and it can damage

your grill and even cause injury.

10. Carefully replace burners.

engagement

11. Attach burners to brackets on firebox.

12. Reposition carryover tubes and attach

to burners. Replace flame tamers and

cooking grates.

Remove screws

To prevent flashbacks and ensure good performance the burner and

venturi assembly should be removed from the grill and cleaned

before use whenever the grill has been idle for an extended period.

Storing Your Grill

• Clean cooking grates.

• Store in dry location.

• When LP cylinder is connected to grill, store outdoors in a well-

ventilated space and out of reach of children.

• Cover grill if stored outdoors. Choose from a variety of grill

covers offered by manufacturers.

Firebox

Electrode

burner

bracket

• Store grill indoors ONLY if LP cylinder is turned off and

disconnected, removed from grill and stored outdoors.

• When removing grill from storage, follow “Cleaning the Burner

Assembly” instructions before starting grill.

Cleaning the Burner Assembly

Electrode

Follow these instructions to clean and/or replace parts of burner

assembly or if you have trouble igniting grill.

1. Turn gas OFF at control knobs and LP cylinder.

2. Remove cooking grates and flame tamers.

Pry off

electrode with

a flat blade

screwdriver

Firebox burner

bracket

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this

product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods

indicated below beginning on the date of purchase*. The manufacturer reserves the right to require that defective parts be returned, postage and or

freight pre-paid by the consumer for review and examination.

SCOPE OF COVERAGE

PERIOD OF COVERAGE

TYPE OF FAILURE COVERAGE

1 year from date of purchase*

PERFORATION, MANUFACTURING,

AND MATERIAL DEFECTS ONLY

All Parts

*Note: A dated sales reciept WILL be required for warranty service.

The original consumer-purchaser will be responsible for all shipping charges for parts replaced under the terms of this limited warranty.

This limited warranty is applicable in the United States and Canada only, is only available to the original owner of the product and is not transferable.

Manufacturer requires proof of your date of purchase. Therefore, you should retain your sales slip or invoice. Registering your product is not a

substitute for proof of purchase and the manufacturer is not responsible for or required to retain proof of purchase records.

This limited warranty applies to the functionality of the product ONLY and does not cover cosmetic issues such as scratches, dents, corrosions or

discoloring by heat, abrasive and chemical cleaners or any tools used in the assembly or installation of the appliance, surface rust, or the

discoloration of stainless steel surfaces. RUST is not considered a manufacturing or materials defect.

This limited warranty will not reimburse you for the cost of any inconvenience, food, personal injury or property damage.

ITEMS MANUFACTURER WILL NOT PAY FOR:

1. Shipping cost, standard or expedited, for warranty and replacement parts

2. Service calls to your home.

3. Repairs when your product is used for other than normal, single-family household or residential use.

4. Damage, failures, or operating difficulties resulting from accident, alteration, careless handling, misuse, abuse, fire, flood,

acts of God, improper installation or maintenance, installation not in accordance with electrical or plumbing codes, or use

of products not approved by the manufacturer.

5. Any food loss due to product failures or operating difficulties.

6. Replacement parts or repair labor costs for units operated outside the United States or Canada.

7. Pickup and delivery of your product.

8. Repairs to parts or systems resulting from unauthorized modifications made to the product.

9. The removal and/or reinstallation of your product.

DISCLAIMER OF IMPLIED WARRANTIES and LIMITATION OF REMEDIES

Repair or replacement of defective parts is your exclusive remedy under the terms of this limited warranty. In the event of parts availability issues,

the manufacturer reserves the right to substitute like or similar parts that are equally functional.

Manufacturer will not be responsible for any consequential or incidental damages arising from the breach of either this limited warranty or any

applicable implied warranty, or for failure or damage resulting from acts of God, improper care and maintenance, grease fire, accident, alteration,

replacement of parts by anyone other than Manufacturer, misuse, transportation, commercial use, abuse, hostile environments (inclement weather,

acts of nature, animal tampering), improper installation or installation not in accordance with local codes or printed manufacturer instructions.

THIS LIMITED WARRANTY IS THE SOLE EXPRESS WARRANTY GIVEN BY THE MANUFACTURER. NO PRODUCT PERFORMANCE

SPECIFICATION OR DESCRIPTION WHEREVER APPEARING IS WARRANTED BY MANUFACTURER EXCEPT TO THE EXTENT SET

FORTH IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTY PROTECTION ARISING UNDER THE LAWS OF ANY STATE,

INCLUDING IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE, IS HEREBY

LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY.

Neither dealers nor the retail establishment selling this product has any authority to make any additional warranties or to promise remedies

in addition to or inconsistent with those stated above. Manufacturer's maximum liability, in any event, shall not exceed the purchase price of the

product paid by the original consumer.

NOTE: Some states do not allow an exclusion or limitation of incidental or consequential damages, so some of the above limitations or exclusions

may not apply to you. This limited warranty gives you specific legal rights as set foth herein. You may also have other rights which vary from state

to state. In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling this product or

the Manufacturer will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumer-purchaser

prior to discovery of the nonconformity. In addition, in the state of California only, you may take the product to the retail establishment selling this

product in order to obtain performance under this limited warranty.

If you wish to obtain performance of any obligation under this limited warranty, you should

write to:

Consumer Relations

P. O. Box 1240

Columbus, GA 31902-1240

Consumer returns will not be accepted unless a valid Return Authorization is first acquired. Authorized returns are clearly marked on the outside of

the package with an RA number and the package is shipped freight/postage pre-paid. Consumer returns that do not meet these standards will be

refused.

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS LIST

Key Qty Description

FIREBOX, GRILL BOTTOM

MAIN BURNER

RIGHT DOOR

CASTER, FIXED

CASTER, LOCKING

CLIP, F/ GREASE CUP

ELECTRODE, MAIN BURNER

BURNER CARRY OVER TUBE

CONTROL PANEL, MAIN

ELECTRONIC IGNITION MODULE

BUTTON, F/ IGNITION MODULE

HOSE VALVE REGULATOR ASSEMBLY

BEZEL F/ CONTROL KNOB

CONTROL KNOB

GREASE CUP

TANK EXCLUSION, LOWER

TEMPERATURE GAUGE BEZEL

ELECTRODE, SIDEBURNER

TANK EXCLUSION, UPPER

ELECTRODE WIRE, F/ SIDEBURNER

SHIELD, F/ ELECTRONIC IGNITOR MODULE

MATCH HOLDER

GRILL LID

LOGO PLATE F/ LID

TEMPERATURE GAUGE

LID BUMPER

NOT Pictured

…

CASTER PIN

HARDWARE PACK

ASSEMBLY MANUAL, ENGLISH

HANDLE, F/ LID

TOP LID HARDWARE

HEAT TENT

COOKING GRATE

WARMING RACK

SIDEBURNER GRATE

LEFT SIDE SHELF F/ SB

DRIP PAN, F/ SB

SIDE BURNER

LEFT CONTROL PANEL, F/ SIDE SHELF

RIGHT SIDE SHELF

PANEL F/ RIGHT SIDE SHELF

SIDEBURNER LID

RIGHT CART FRAME

LEFT CART FRAME

GROMMET, F/ REGULATOR HOLE

REAR CART BRACE

BOTTOM SHELF

MAGNET ASSEMBLY

WING SCREW TANK

FRONT DOOR BRACE

LEFT DOOR

DOOR HANDLE

NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from

those on your particular grill model. However, the method of assembly remains the same.

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

Place bottom shelf upside down. Insert Caster Pin into the caster mounting plate to lock it in place, shown A.

Spin the caster clockwise into the threads on the bottom shelf until secure. Remove the Caster Pin and repeat for remaining

casters. Make sure the two locking casters are secured at the rear and the non-locking casters are secured at the front.

After all 4 casters are secure remove the Caster Pin and save for future maintenance.

Fixed caster

Locking caster

Caster pin

Bottom shelf

Attach side panels to bottom shelf using three 1/4-20x1/2”

screws, 7mm lock washers, and 7mm flat washers per panel.

IMPORTANT: Panel with large hole must

Be on left side of bottom shelf.

1/4-20x1/2” screw

7mm lock washer

7mm flat washer

Right side panel

Make sure side panels

are pushed as far to the

rear of bottom shelf as

possible before fully

tightening screws.

Left side panel

(with large hole)

Download from Www.Somanuals.com. All Manuals Search And Download.

Attach front brace to side panels using two #10-24X1/2” screws, 5mm lock washers and 5mm flat washers on each side.

Magnet

5mm flat washers

#10-24x1/2”

screws

5mm lock washers

Attach rear cart brace to cart frames using two #8-32x1/2” screws, 4mm lock washers and 4mm flat washers on each side.

Download from Www.Somanuals.com. All Manuals Search And Download.

Insert wire ends on lower tank exclusion wire into bottom shelf (A). Attach with two #8-32x3/8" screws diagonally. Place

upper tank exclusion wire on front brace and back brace as shown, secure with two #8-32x3/8" screws and #8-32 flange

nuts (B).

Magnet

Front brace

#8-32

flange nut

Upper tank

exclusion wire

#8-32x3/8"

screw

Lower tank

exclusion wire

Two #8-32x3/8" machine screws are installed partially in the cart side panel. Slide door hinges onto the screws as shown.

Secure right door with four #8-32x3/8" machine screws. Repeat assembly for left door.

#8-32x3/8”

machine screws

Download from Www.Somanuals.com. All Manuals Search And Download.

This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart. Make sure the

regulator hose is hanging outside the cart. Insert 1/4-20x1/2" screws through side panels and firebox in all four corners. Secure with

fiber washers and 1/4-20 flange nuts.

1/4-20 flange nut

Fiber washer

1/4-20x1/2" screw

Mount fascia onto side shelf using three #10-24x1/2" screws, 5mm lock washers

and 5mm flat washers (A). Hang side shelf on the tabs mounted on the firebox.

CAUTION

Secure shelf brackets to cart side panel using two 1/4-20x1/2" screws, fiber

washers and 1/4-20 flange nuts on each bracket (B). Secure fascia to firebox

using two 1/4-20x1/2" screws, 7mm lock washers and 7mm flat washers (C).

SHARP EDGES! Wear gloves if necessary

Repeat on front bracket

1/4-20x1/2"

screw

1/4-20 flange nut

Fiber washer

#10-24x1/2" screw

Flat washer

Lock washer

Flat washer

Lock washer

1/4-20x1/2"

screw

Repeat on left side shelf

Download from Www.Somanuals.com. All Manuals Search And Download.

Repeat step 7 (A) on left side shelf. Hang sideburner shelf on tabs mounted on

the firebox. Secure shelf brackets to cart side panel using two 1/4-20x1/2"

screws, fiber washers and 1/4-20 flange nuts on each bracket (A).

Secure fascia to firebox using two 1/4-20x1/2" screws, 7mm lock washers and

7mm flat washers (B).

flange

nut

7mm lock

washer

7mm flat

CAUTION

washer

SHARP EDGES! Wear gloves if necessary.

1/4-20x1/2”

screw

Place drip pan onto sideburner shelf. Secure with #10-24x 1/2" screws, 5mm fiber washers, 5mm flat washers, 5mm

lock washers , #10-24 hex nuts, #10-24x 1/2” screws, 5mm lock washers, 5mm flat washers and side burner lid

supports.

#10-24 x ½" Screws

5mm Fiber Washers

5mm Flat Washers

5mm Lock Washers

#10-24 Hex Nut

5mm Flat Washers

5mm Lock Washers

#10-24 x ½" Screws

Download from Www.Somanuals.com. All Manuals Search And Download.

Remove two #8-32x3/8" screws from sideburner valve bracket. From behind the fascia, place sideburner valve bracket into

hole. Attach bezel to valve with #8-32x3/8" screws. Press sideburner control knob onto valve stem.

Sideburner

valve bracket

Control knob bezel

Control knob

Insert sideburner into sideburner drip pan (A), make sure burner tube engages with sideburner valve. Illustration (B) shows

correct burner-to-valve engagement. Center stud on bottom of sideburner fits into center hole in sideburner drip pan. Secure

with one wingnut (C). Connect sideburner ignitor wire to sideburner electrode.

Sideburner

Electrode

Sideburner

ignitor wire

Download from Www.Somanuals.com. All Manuals Search And Download.

Place sideburner cooking grate into holes in drip pan.

Sideburner

grate

Place four flame tamers over burners by inserting tabs into slots in front of firebox. Opposite ends of flame tamers rest on

pins in back of firebox.

Download from Www.Somanuals.com. All Manuals Search And Download.

Place cooking grates into grill bottom.

Cooking Grates

To assemble Swing Away, first insert pivot wire into holes in side of grill lid. Second, insert leg wires into holes in sides

of grill bottom.

Pivot wire

Swing Away

Leg wire

Download from Www.Somanuals.com. All Manuals Search And Download.

Hang grease cup wire from bottom of firebox and place grease cup into grease cup clip.

CAUTION

Failure to install grease cup will cause

hot grease to drip from bottom of grill

with risk of fire or property damage.

Grease Cup Wire

Grease Cup

Unscrew ignitor cap and place AA battery into ignitor slot with positive end (+) facing outward. Screw ignitor cap onto ignitor.

AA Battery

–

Download from Www.Somanuals.com. All Manuals Search And Download.

LP tank is sold separately. Fill and leak check the tank (see Use & Care section) before attaching to grill and regulator.

Once tank has been filled and leak checked, place tank into tank hole in bottom shelf. Make sure tank valve is facing front of

grill. Put regulator assembly through circular opening of cart side panel. Connect regulator to tank valve securely. Secure

tank with tank screw at rear of bottom shelf. Ensure Over Pressure Device (OPD) of tank valve face to front door.

See Use & Care manual to perform the "Burner Flame Check" and for important safety instructions before

using.

LP Cylinder

(not included)

CAUTION

Cylinder valve must face to front of cart once

tank is attached. Failure to install cylinder

correctly may allow gas hose to be damaged

in operation, resulting in the risk of fire.

Tank screw

Download from Www.Somanuals.com. All Manuals Search And Download.

DANGER: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.

Emergencies

Possible Cause

Prevention/Solution

Gas leaking from

cracked/cut/burned

hose.

• Damaged hose.

• Turn off gas at LP cylinder or at source on natural gas systems. If

anything but burned, replace valve/hose/regulator. If burned,

discontinue use of product until a plumber has investigated cause

and corrections are made.

Gas leaking from LP

cylinder.

• Mechanical failure due to rusting or

mishandling.

• Replace LP cylinder.

Gas leaking from LP

cylinder valve.

• Failure of cylinder valve from

• Turn off LP cylinder valve. Return LP cylinder to gas supplier.

mishandling or mechanical failure.

Gas leaking between

LP cylinder and

• Improper installation, connection not

tight, failure of rubber seal.

• Turn off LP cylinder valve. Remove regulator from cylinder and

visually inspect rubber seal for damage. See LP Cylinder Leak Test

and Connecting Regulator to the LP Cylinder.

regulator connection.

Fire coming through

control panel.

• Fire in burner tube section of burner due

to blockage.

• Turn off control knobs and LP cylinder valve. Leave lid open to

allow flames to die down. After fire is out and grill is cold, remove

burner and inspect for spider nests or rust. See Natural Hazard

and Cleaning the Burner Assembly pages.

Grease fire or

• Too much grease buildup in burner area.

• Turn off control knobs and LP cylinder valve. Leave lid open to

allow flames to die down. After cooling, clean food particles and

excess grease from inside firebox area, grease tray, and other

surfaces.

continuous excessive

flames above cooking

surface.

Troubleshooting

Problem

Possible Cause

Prevention/Solution

GAS ISSUES:

Burner(s) will not light

using ignitor.

• Trying to light wrong burner.

• See instructions on control panel and in Use and Care section.

• Make sure valves are positioned inside of burner tubes.

(See Electronic Ignition

Troubleshooting also)

• Burner not engaged with control valve.

• Obstruction in burner.

• Ensure burner tubes are not obstructed with spider webs or other

matter. See cleaning section of Use and Care.

Continued on next

page.

• No gas flow.

• Make sure LP cylinder is not empty. If LP cylinder is not empty,

refer to “Sudden drop in gas flow.”

• For a grill equipped with the AUTO-CLEAN™ feature, make sure

the AUTO-CLEAN™ valve is set to “Grill”

• Vapor lock at coupling nut to LP cylinder.

• Turn off knobs and disconnect coupling nut from LP cylinder.

Reconnect and retry.

• Coupling nut and LP cylinder valve not

fully connected.

• Turn the coupling nut approximately one-half to three-quarters

additional turn until solid stop. Tighten by hand only - do not use

tools.

ELECTRICAL ISSUES:

• Electrode cracked or broken; “sparks at

crack.”

• Replace electrode(s).

• Electrode tip not in proper position.

Main Burners:

• Tip of electrode should be pointing toward gas port opening on

burner. The distance should be 1/8” to 1/4”. Adjust if necessary.

Sideburner:

• Tip of electrode should be pointing toward gas port opening on

burner. the distance should be 1/8” to 3/16”. Adjust if necessary.

• Wire and/or electrode covered with

cooking residue.

• Clean wire and/or electrode with rubbing alcohol and clean swab.

• Wires are loose or disconnected.

• Reconnect wires or replace electrode/wire assembly.

• Replace ignitor wire/electrode assembly.

• Wires are shorting (sparking) between

ignitor and electrode.

• Dead battery.

• Replace with a new alkaline battery.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting (continued)

Problem

Possible Cause

Prevention/Solution

Burner(s) will not light

using ignitor.

ELECTRONIC IGNITION:

• No spark, no ignition noise.

• See Section I of Electronic Ignition System.

• See Section II of Electronic Ignition System.

• See Section III of Electronic Ignition System.

(See Electronic Ignition

Troubleshooting also)

• No spark, some ignition noise.

• Sparks, but not at electrode or at full

strength.

Burner(s) will not

match light.

• See “GAS ISSUES:” on previous page.

• Match will not reach.

• Use long-stem match (fireplace match).

• Improper method of match-lighting.

• Out of gas.

• See “Match-Lighting” section of Use and Care.

• Check for gas in LP cylinder.

Sudden drop in gas

flow or low flame.

• Excess flow valve tripped.

• Turn off knobs, wait 30 seconds and light grill. If flames are still low,

turn off knobs and LP cylinder valve. Disconnect regulator.

Reconnect regulator and leak-test. Turn on LP cylinder valve, wait

30 seconds and then light grill.

• Vapor lock at coupling nut/LP cylinder

connection.

• Turn off knobs and LP cylinder valve. Disconnect coupling nut from

cylinder. Reconnect and retry.

Flames blow out.

Flare-up.

• High or gusting winds.

• Low on LP gas.

• Turn front of grill to face wind or increase flame height.

• Refill LP cylinder.

• Excess flow valve tripped.

• Grease buildup.

• Refer to “Sudden drop in gas flow” above.

• Clean burners and inside of grill/firebox.

• Excessive fat in meat.

• Trim fat from meat before grilling.

• Excessive cooking temperature.

• Adjust (lower) temperature accordingly.

Persistent grease fire.

• Grease trapped by food buildup around

burner system.

• Turn knobs to OFF. Turn gas off at LP cylinder. Leave lid in position

and let fire burn out. After grill cools, remove and clean all parts.

Flashback...

• Burner and/or burner tubes are blocked.

• Turn knobs to OFF. Clean burner and/or burner tubes. See burner

cleaning section of Use and Care.

(fire in burner tube(s)).

Unable to fill LP

cylinder.

• Some dealers have older fill nozzles

with worn threads.

• The worn nozzles don’t have enough “bite” to engage the valve. Try

a second LP dealer.

One burner does not

light from other

burner(s).

• Grease buildup or food particles in

end(s) of carryover tube(s).

• Clean carry-over tube(s) with wire brush.

AUTO-CLEAN™

Possible Cause

Prevention/Solution

(If Equipped)

ŸReplace batteries

Timer does not work

(Green light does not

flash)

ŸDead Battery

Install batteries correctly.

ŸBatteries installed incorrectly.

ŸKnob Position did not start the Clean

Cycle

ŸPush Knob in to start the clean cycle. (Green LED should begin to

flash)

ŸReplace batteries

No LED’s will illuminate

ŸDead Battery

ŸPrepare to replace batteries (NOTE: Clean cycle will operate with

Red LED next to battery

symbol is illuminated

ŸLow Battery Strength

a weak battery.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting - Electronic Ignition

Problem (Ignition)

Possible Cause

Check Procedure

Prevention/Solution

SECTION I

• Battery not installed

properly.

• Check battery orientation.

• Install battery (make sure that “+” and “–”

connectors are oriented correctly, with “+” end up

and “–” end down.)

No sparks appear at

any electrodes when

Electronic Ignition Button

is pressed; no noise can

be heard from spark

module.

• Dead battery.

• Has battery been used

previously?

• Replace battery with new alkaline battery.

• Button assembly not

installed properly.

• Check to insure threads are

properly engaged. Button

should travel up and down

without binding.

• Unscrew button cap assembly and reinstall, making

sure threads are aligned and engaged fully.

• Faulty spark module.

• If no sparks are generated

with new battery and good

wire connections, module is

faulty.

• Replace spark module assembly.

SECTION II

• Output lead

connections not

connected.

• Are output connections on

and tight?

• Remove and reconnect all output connections at

module and electrodes.

No sparks appear at

any electrodes when

Electronic Ignition Button

is pressed; noise can

be heard from spark

module.

• Output lead

connections not

connected.

• Are output connections on

and tight?

• Remove and reconnect all output connections at

module and electrodes.

SECTION III

Sparks are present

but not at all

electrodes and/or not

at full strength

• Arcing to grill away

from burner(s).

• If possible, observe grill in

dark location. Operate

ignition system and look for

arcing between output wires

and grill frame.

• If sparks are observed other than from burner(s),

wire insulation may be damaged. Replace wires.

• Weak battery.

• All sparks present but weak

or at slow rate.

• Replace battery with a new alkaline battery.

• Use paper towel to remove moisture.

• Electrodes are wet.

• Has moisture accumulated

on electrode and/or in burner

ports?

• Electrodes cracked or

broken “sparks at

crack”.

• Inspect electrodes for

cracks.

• Replace cracked or broken electrodes.

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

Please register your product online at:

www.charbroil.com/register

(If you register online, you do not need to send in this registration card.)

PLEASE FILL OUT THIS CARD AND ATTACH A COPY OF YOUR SALES RECEIPT. RETURN IT WITHIN 10 DAYS OF PURCHASE. FOR WARRANTY SERVICE PROOF OF PURCHASE

WILL BE REQUIRED. THIS WARRANTY IS NON‐TRANSFERABLE.

LLENE ESTA TARJETA Y DEVUELVALA DENTRO DE LOS 10 DIAS DE LA COMPRA. PARA EL SERVICIO DE GARANTIA ES NECESARIO QUE PRESENTE SU COMPROBANTE DE

COMPRA. CONSERVE LA FACTURA. ESTA GARANTIA ES INTRANSFERIBLE.

VEUILLEZ COMPLETER CETTE CARTE ET LA RETOURNER DANS LES 10 JOURS SUIVANT L’ACHAT. POUR OBTENIR LE SERVICE SOUS GARANTIE, UNE PREUVE D’ACHAT DOIT

ETRE PRESENTEE. VEUILLEZ CONSERVER VOTRE FACTURE. LA PRESENTE GARANTIE N’EST PAS TRANSFERABLE.

*Required | Necesario | Exigé

~ PLEASE PRINT ~ IMPRIMA POR FAVOR ~ S'IL VOUS PLAÎT IMPRIMER ~

* 1 First Name | Nombre | Prénom

Initial | Inicial | Initiale

Last Name | Apellido | Nom de Famillie

Address (number & street) | Dirección (número y calle) | Adresse (numéro et rue)

Apt Number | Nºde apart | Nºd’appt.

Zip Code | Código Zip | Code Postal

City | Cludad | Ville

State | Estado | Province

* 2 ^{E‐mail Address | Dirección de correo electrónico | Adresse électronique}

* 3 ^{Phone Number | Número telefónico | Numéro de téléphone}

* 4 ^{Model Number | Número de modelo | Numéro de modèle}

* 5 Attach copy of your

STICKER ON PRODUCT

Serial Number | Número de serie| Numéro de série

sales receipt here.

Adjunte aqui la copia

de su recibo de

compra

Date of Purchase | Fecha de compra | Date de l’achat

Store Name | Nombre de la tienda | Nom du magasin

Purchase Price | Precio de compra | Prix d’achat

Your Gender | Sexo | Sexe:

Male | Masculino | Masculin

Female | Femenino | Féminin

Veuillez attacher une

copie de votre reçu

ici.

10 Which product are you registering?

¿Qué producto está registrando?

Quel produit enregistrez‐vous?

Mail to: / Envíelo a:

Gas Grill | Parrilla a gas | Gril au gaz

Electric Grill | Parrilla eléctrica | Gril électrique

Smoker | Ahumador | Fumoir

Charcoal Grill | Parrilla a carbón | Barbecue au charbon

Cooker/Fryer | Cocina/freidora | Cuiseur/Friteuse

Other | Otro | Autre

Char‐Broil Warranty Registration

P.O. Box 1240

Columbus, GA 31902‐1240

We respect your privacy. | Respetamos su privacidad. | Nous respectons votre vie privée.

If you prefer not to receive special offers and promotions from Char‐Broil, please check here:

Marque aquí si no desea recibir ofertas y promociones especiales de Char‐Broil:

Si vous préférez ne pas recevoir d’informations concernant des offres spéciales et des

promotions de Charbroil, veuillez cocher ici:

Thank you for completing this questionnaire. | Gracias por completer este cuestionario. | Merci d’avoir bien voulu remplir ce questionnaire.

Download from Www.Somanuals.com. All Manuals Search And Download.

Black Decker Cordless Drill 611306 00 User Manual
Breville Hot Beverage Maker BKE830 User Manual
BRK electronic Carbon Monoxide Alarm C0250LBT User Manual
Brother Copier 4750e User Manual
Brother Sewing Machine BM 3500 User Manual
Campbell Hausfeld Nail Gun NB004100 User Manual
Cannon Scanner DR 2580C User Manual
Canon Film Camera F1 N User Manual
Canon Projector SX6000 User Manual
Cateye Home Safety Product ABS 10 User Manual