®
Model RGAIPI
Wireless Gate Access Intercom
Talk Button: Following the ringing
Overview
of the doorbell by a guest, press
and hold the Talk button to talk to
the guest. Once the link to the
Outdoor Intercom is made, any
other intercoms in the network
cannot hear the conversation.
Select Button: During a conversation, the Select
button can be pressed to open the gate. A beep will
be heard and the gate will open. To open the gate
when not in a conversation, press and hold the Select
Button for 10 seconds.
The Wireless Gate Access Intercom allows
homeowners to communicate with guests at the gate
and operate the gate from inside the house. The
Indoor Intercom emits a doorbell sound and
establishes a secure 900 Mhz digital radio link with
the Outdoor Intercom. The Wireless Gate Access
Intercom is compatible with various Chamberlain
Wireless Products and all Chamberlain Gate
Operators.
Carton Inventory
Volume: Pressing the Volume
button repeatedly will cycle through
volume levels.
Battery: The AA Alkaline batteries
(not provided) will last up to a year
depending on use (Lithium batteries
recommended for colder
Rubber Pads
environments). When batteries are
low intercom will emit two beeps
every ten minutes.
Indoor Intercom
An AC Adapter (not provided) can
also be used to power the
intercom. In this case, both the
power and channel lights will
OPTIONAL
Mounting Tape
remain on.
Outdoor Intercom
Alcohol Wipe
Call Button
Learn Button
Dipswitch
Outdoor Intercom
Block
Speaker
Operation & Features
Indoor Intercom
Call Button: To communicate with the Indoor
Intercom, press and release the Call button. A
doorbell sound will be heard on the Indoor Intercom.
Once a secure link is made, the Call button on the
Outdoor Intercom does not need to be pressed to
speak again.
Volume Button
Battery: The AA Alkaline batteries (not provided) will
last up to a year depending on use. (Lithium batteries
recommended for colder environments.)
Volume: To increase the Outdoor Intercom volume,
set Dipswitch #4 to OFF.
Talk
(Power - On)
Select Button
AC Adapter
Sensitivity: To increase sensitivity on
the Outdoor Intercom set Dipswitch #3
to OFF.
NOTE: Dipswitch #1 must always
remain ON. Dipswitch #2 is not used.
Learn Button
Dipswitch #1
Dipswitch #2
On/Off: To turn Indoor Intercom ON, press any
button. To turn Indoor Intercom OFF, hold down the
Volume button for 5 seconds.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting with Tape
Mount Outdoor Intercom
Step 1
The Outdoor Intercom should be mounted where it is
easily accessible to a driver. The Outdoor Intercom
can be mounted by using the included screws or by
using the double-sided mounting tape. It is
recommended to use the mounting tape on surfaces
such as metal or glass.
Mounting with Screws
Step 1
Clean back of Outdoor Intercom and mounting
surface using the alcohol wipe.
Step 2
Mount Outdoor Intercom with small silver screws.
Screw the top two screws halfway into the mounting
surface. Place back of Outdoor Intercom over screws.
Tighten screws.
Peel off white paper from mounting tape. Firmly press
mounting tape on back of Outdoor Intercom.
Step 2
Step 3
Put the remaining silver screws into the bottom holes
of Outdoor Intercom. Tighten screws.
Peel paper from mounting tape. Firmly press Outdoor
Intercom onto mounting surface.
Secure Cover
Secure cover with the
two large black screws.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Additional Intercoms
Troubleshooting
Indoor Intercom does not receive voice
transmission from Outdoor Intercom.
Check the batteries in both intercoms. Ensure the
Indoor Intercom is programmed to the Outdoor
Intercom. See Program Indoor Intercom to Outdoor
Intercom.
NOTE: Some older versions of Chamberlain Wireless
Intercoms are not compatible with the Gate Access
Intercom. Ensure that the additional intercoms state
that they are compatible with Chamberlain's Gate
Access Intercom.
The Indoor Intercom can be programmed to at least
one other intercom to become a network or it can be
programmed into an existing network. Any intercom
that has been programmed into the network can
respond to a call and operate the gate.
Indoor Intercom is not getting expected
transmission range.
Keep antenna vertical. Keep Outdoor Intercom away
from trees, metal objects and electrical wiring. Cell
phones, cordless phones, or other radio devices near
the Indoor Intercom may also limit range.
Indoor Intercom beeps once every ten minutes.
The battery is low in the Indoor Intercom. Replace
with AA Alkaline batteries or operate it with AC
Adapter (not provided). A 9-12 volt, 500mA AC
Adapter may be used (center positive polarity on the
round plug).
Press the Learn button on the Indoor Intercom until a
beep is heard. Within 10 seconds put the new
intercom into Learn Mode (refer to table below).
Indoor Intercom beeps three times every ten
minutes.
The battery is low in the Outdoor Intercom. Replace
INTERCOM
OR
LEARN MODE
Press the Learn
button until a beep is
heard.
with AA Alkaline batteries.
Need to clear Indoor Intercom’s memory.
Press and hold Learn button, an initial beep will be
heard. Continue to hold until a second beep is heard
(about 15 seconds). Ensure other intercoms are not
activated during this time. Intercoms in the network
that are on will signal during the clearing process.
Once memory is clear the intercom can be
programmed to a new network.
Press and hold
both buttons for 5
seconds.
Each intercom will emit a tone when programmed into
network. Repeat for any additional intercoms.
NOTE: Do not program new intercoms to each other
before adding them to the network or they will form a
separate network and the memory will need to be
cleared.
Outdoor Intercom does not function.
Check batteries in Outdoor Intercom. When you press
the Call button you should hear a tone.
Ensure Outdoor Intercom is connected to a network.
Press and release the Talk button on the Indoor
Intercom to verify network is complete.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Template
1 3/8"
4 1/4"
2"
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:
1-800-528-9131
www.chamberlain-DIY.com
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.
THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
© 2008, The Chamberlain Group Inc.
All Rights Reserved
114A3670B
Download from Www.Somanuals.com. All Manuals Search And Download.
|