Chamberlain Garage Door Opener PD210D User Manual

The Chamberlain Group, Inc.

845 Larch Avenue

Elmhurst, Illinois 60126-1196

www.chamberlain.com

GARAGE DOOR OPENER

ASSEMBLY/INSTALLATION MANUAL

■

Please read this manual and the enclosed safety materials carefully!

Fasten the manual near the garage door after installation.

The door WILL NOT CLOSE unless the Protector System is connected

and properly aligned.

■

Periodic checks of the opener are required to ensure safe operation.

The model number label is located under the light lens on the front panel of

your opener.

PD210D • PD212D

248730

PD610D • PD612D • 7920KD

PD612KLD • 48930D

There are two types of garage door openers pictured. Yours may appear slightly different.

IMPORTANT SAFETY NOTES

This garage door opener has been designed and tested to offer safe service provided it is installed, operated,

maintained and tested in strict accordance with the instructions and warnings contained in this manual.

When you see these Safety Symbols and Signal Words on

the following pages, they will alert you to the possibility of

serious injury or death if you do not comply with the

warnings that accompany them. The hazard may come

WARNING

Mechanical

from something mechanical or from electric shock. Read

the warnings carefully.

WARNING

Electrical

When you see this Signal Word on the following pages, it

will alert you to the possibility of damage to your garage

door and/or the garage door opener if you do not comply

with the cautionary statements that accompany it. Read

them carefully.

CAUTION

Download from Www.Somanuals.com. All Manuals Search And Download.

PLANNING

WARNING

Identify the type and height of your garage door. If you

have a one-piece door, follow the assembly

instructions contained in this manual and refer to the

Installation Instructions One-Piece Door for

installation procedures. Survey your garage area to see

if any of the conditions below apply to your installation.

Additional materials may be required. You may find it

helpful to refer back to this page and the accompanying

illustrations as you proceed with the installation of your

opener.

Without a properly working safety reversal system, persons

(particularly small children) could be SERIOUSLY INJURED or

KILLED by a closing garage door.

• The gap between the bottom of the garage door and the floor

MUST NOT exceed 1/4" (6 mm). Otherwise, the safety

reversal system may not work properly.

• The floor or the garage door MUST be repaired to eliminate

the gap.

• Do you have an access door in addition to the garage

door? If not, Model 7702CB Outside Quick Release is

required. See Accessories page.

Depending on your requirements, there are several

installation steps which may call for materials or hardware

not included in the carton.

• Look at the garage door where it meets the floor. Any

gap between the floor and the bottom of the door must

not exceed 1/4" (6 mm). Otherwise, the safety reversal

system may not work properly. See Adjustment Step 3.

Floor or door should be repaired.

• Installation Page 10 – Look at the wall or ceiling above

the garage door. The header bracket must be securely

fastened to structural supports.

• Installation Page 12 – Do you have a finished ceiling in

your garage? If so, a support bracket and additional

fastening hardware may be required.

• The opener should be installed above the center of the

door. If there is a torsion spring or center bearing plate

in the way of the header bracket, it may be installed

within 4 feet (1.22 m) to the left or right of the door

center.

• Installation Page 13 – Do you have a steel, aluminum,

fiberglass or glass panel door? If so, horizontal and

vertical reinforcement is required.

• Installation Page 18 – Depending upon garage

construction, extension brackets or wood blocks may be

needed to install sensors.

• If your door is more than 7 feet (2.13 m) high, see rail

extension kits listed on Accessories page 32.

• Installation Page 18 – Alternate floor mounting of the

safety reversing sensor will require hardware not

provided.

COMPLETED INSTALLATION

FINISHED CEILING

Support bracket &

fastening hardware

is required.

See page 12.

Horizontal and vertical reinforcement

is needed for lightweight garage doors

(fiberglass, steel, aluminum, door with

glass panels, etc.) See page 13 for details.

Slack in chain tension

is normal when

Rail

garage door is closed.

Header Wall

Torsion Spring

CLOSED POSITION

Trolley

Header

Bracket

Trolley

Stop Bolt

Wall-mounted

Door Control

Access

Door

Garage

Center of

Door

Garage door

Chain

Spring

Straight

Door

Emergency

Release

Arm

Rope & Handle

Curved

Door

Header

Wall

Arm

Door

Safety

Garage

Bracket

Gap between floor

Reversing

Sensor

Door

and bottom of door

Safety Reversing

must not exceed 1/4"

Sensor

Download from Www.Somanuals.com. All Manuals Search And Download.

TOOLS NEEDED

2 X 4 Board

Drill

1/4" Nutdriver

Wire Cutters

Drill Bits

Carpenter's

3/16", 5/16"

and 5/32"

Level (Optional)

Pliers

Tape Measure

Adjustable End Wrench

Sockets and Wrench

1/2", 5/8", 7/16", 9/16"

and 1/4"

Stepladder

Phillips and Flat Screwdriver

Pencil

Hack Saw

Claw Hammer

Your garage door opener is packaged in one carton which contains the motor unit and the parts illustrated below. Note

that accessories will depend on the model purchased. If anything is missing, carefully check the packing material. Parts

may be stuck in the foam. Hardware for assembly and installation is shown on the next page. Save the carton and

packing material until installation and adjustment is complete.

OPENER CONTENTS

A11

A20

CLOSED

OPEN

“U” Bracket

Garage Door Monitor

(Model 7920KD only)

Rail

Door

Center/Back

Sections (4)

Control

All Other

Models

A19

Hanging Brackets

LOCK

LIGHT

Keyless Entry

Rail

Models

Front (header)

Section (1)

PD612KLD (1)

7920KD (1)

Straight Door

Arm Section

A12

A13

A14

Chain Spreader

with Screws

Idler Pulley

Chain and Cable in

Dispensing Carton

Curved Door

Arm Section

(included with hardware)

Safety Labels

and Literature

Trolley

Header Bracket

Models

PD210D (1)

PD610D (1)

PD612D (2)

PD612KLD (2)

48930D (2)

7920KD (2)

A16

PD212D (2)

248730 (1)

Motor Unit with Light Lenses

(varies depending

Remote Control Transmitter

A10

upon model purchased)

A15

A21

A17

The Protector System

A18 Assembly and

Installation Hardware

(2) Safety Reversing Sensors

(1 Sending Eye and 1 Receiving Eye)

with 2-Conductor White and White/Black

Bell Wire attached

Safety Sensor

Bracket (2)

Door Bracket

Door Control Button

Model 248730 ONLY

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY HARDWARE

Threaded

Trolley Shaft (1)

Nut 3/8" (1)

Bolt 1/4" - 20 x 1-3/4" (2)

Idler Bolt (1)

Lock Nut

Lock Washer

3/8" (1)

1/2" - 20 (2)

Master Link (2)

INSTALLATION HARDWARE

Lag Screw

Hex Bolt

Spacer (2)

Nut 5/16" - 18 (4)

Rail Grease

5/16"-18 x 1-7/8" (2)

5/16"- 18 x 7/8" (4)

Insulated

Staples (30)

C11

Clevis Pin

5/16" x 1-1/2" (1)

Self-Threading Screw

1/4"-14 x 5/8" (2)

C10

Ring

Clevis Pin

5/16" x 1-1/4" (1)

Lock Washer

5/16" (7)

Fastener (3)

C19

Drywall

C15

Screw

C12

C18

Anchors (2)

C13 Screw 6-32 x 1" (2)

6AB x 1-1/4" (2)

Rope

Carriage Bolts

C14

1/4"-20 x 1/2" (2)

C20

C17

C16

NOTICE

C21

Wing Nut

2-Conductor Bell Wire

White & White/Red

Clevis Pin

Handle (not shown

actual size)

1/4 x 20 (2)

Lag Screw

5/16" x 1" (1)

5/16"- 9 x 1-5/8" (2)

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

CAUTION

To prevent INJURY from pinching, keep hands and fingers

away from the joints while assembling the rail.

Assemble the Rail

As a temporary trolley stop,

insert a screwdriver into the

hole 10" (25 cm) away from

the front of the rail, as shown.

Idler

Pulley

Hole

KEEP SMALL HOLES

ALONG OPPOSITE EDGE

OF RAILS

Window

Cut-Out

A13

As a temporary trolley stop,

insert a screwdriver into the

hole 10" (25 cm) away from

the front of the rail, as shown.

10" (25 cm)

KEEP LARGER

HOLE ON TOP

FRONT RAIL

(TOP)

Window

Cut-Out

A11 “U” Bracket

B6 Bolt

Cover

Protection

Bolt Hole

Trolley

Stop Hole

TO MOTOR UNIT

SLIDE RAIL TO STOPS

ON TOP AND SIDES

OF BRACKET

B3 Lock Nut

Front Rail

(TO DOOR)

Back Rails

(TO MOTOR UNIT)

A11 “U” Bracket

ALL HARDWARE SHOWN ACTUAL SIZE

B6 Bolt

B3 Lock Nut

Download from Www.Somanuals.com. All Manuals Search And Download.

CAUTION

To avoid serious damage to opener, ONLY use bolts/fasteners

mounted in top of motor unit.

Remove Fasteners from

Top of Motor Unit

Attach Rail to Motor Unit

Attach Chain Spreader

Hex Screws

8-32x7/16"

Bolt

Chain

Spreader

Run Cable Through

Cut-Out Window

Install Idler Pulley

Attach Cable to Front

of Trolley

Bolt

Chain

and Cable

Rail

Do NOT remove

Chain/Cable

from box

Pulley

A2 Chain and Cable

Do NOT remove

Chain/Cable

from box

Nut

Washer

Master Link

Clip-On Spring

Idler Bolt

A12 Idler Pulley

Cable

Loop

Lock Washer

Master

Link Bar

Cable Loop

B7 Nut

Cable Loop

ALL HARDWARE SHOWN ACTUAL SIZE

B4 Master Link

B5 Idler Bolt

B7 Nut

B3 Lock Nut

B2 Lock Washer

Download from Www.Somanuals.com. All Manuals Search And Download.

CAUTION

To avoid possible SERIOUS INJURY to fingers:

• Securely attach chain spreader.

• NEVER connect garage door opener to power source until

instructed to do so.

Route Chain/Cable Around Rail Assembly

and Motor Unit Sprocket

Leave chain/cable inside

carton to prevent kinking

Chain and

Cable in

Dispensing

Carton

Cable

Motor Unit

Chain

Sprocket

Attach Chain To Trolley

Threaded Shaft

Attach Nut and Lock

Washer to Trolley

Threaded Shaft

Insert Trolley Threaded

Shaft into Round Hole in

Trolley

Master Link

Clip-On Spring

Trolley

Threaded

Shaft

Trolley

Threaded

Shaft

Trolley

Threaded

Shaft

Inner Nut

Lock

Lock Washer

Washer

Outer Nut

Master

Link Bar

Tighten the Chain

Desired Chain Tension

A2 Chain

1/4" (6 mm)

Base of Rail

Mid Length of Rail

Assembly of your opener is now complete.

ALL HARDWARE SHOWN ACTUAL SIZE

B1 Threaded Trolley Shaft

B4 Master Link

C4 Nut

C5 Lock Washer

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND

INSTRUCTIONS.

2. Install garage door opener ONLY on properly balanced and

lubricated garage door. An improperly balanced door may not

reverse when required and could result in SEVERE INJURY or

DEATH.

3. ALL repairs to cables, spring assemblies and other hardware

MUST be made by a trained door systems technician BEFORE

installing opener.

8. NEVER wear watches, rings or loose clothing while installing

or servicing opener. They could be caught in garage door or

opener mechanisms.

9. Install wall-mounted garage door control:

• within sight of the garage door

• out of reach of children at minimum height of 5 feet (1.5 m)

• away from ALL moving parts of the door.

10. Place entrapment warning label on wall next to garage door

control.

4. Disable ALL locks and remove ALL ropes connected to garage

door BEFORE installing opener to avoid entanglement.

11. Place manual release/safety reverse test label in plain view on

inside of garage door.

5. Install garage door opener 7 feet (2.13 m) or more above floor.

6. Mount emergency release handle 6 feet (1.83 m) above floor.

7. NEVER connect garage door opener to power source until

instructed to do so.

12. Upon completion of installation, test safety reversal system.

Door MUST reverse on contact with a 1-1/2" high (3.8 cm)

object (or a 2 x 4 laid flat) on the floor.

One-Piece Door

Sectional Door

If you have a one-piece door, proceed to the

One-Piece Door Installation Instructions included

with your garage door opener.

If you have a sectional door, proceed to page 10

of this manual.

INSTALLATION

INSTRUCTIONS

FOR ONE-PIECE

DOORS

PAGE 10

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

WARNING

To prevent possible SERIOUS INJURY or DEATH:

• Header bracket MUST be RIGIDLY fastened to structural

support on header wall or ceiling, otherwise garage door

might not reverse when required.

INSTALL THE HEADER BRACKET

• NEVER try to loosen, move or adjust garage door, springs,

cables, pulleys, brackets, or their hardware, ALL of which are

under EXTREME tension.

NOTE: You can fasten the header bracket within 4 feet

(1.2 m) of the left or right of the door center only if a

torsion spring or center bearing plate is in the way; or

you can attach it to the ceiling when clearance is

minimal.

Fasten header bracket securely to structural supports.

It may be necessary to use a 2 x 4 as a structural

support if installing on drywall or between two studs as

shown in Step 3. Securely fasten 2 x 4 to structural

supports using lag screws (not provided). Concrete

anchors must be used if mounting header bracket or

2 x 4 into masonry.

Mark the Center of the

Garage Door

Mark the center of the garage door on door

and wall and extend onto the ceiling

door, wall a

Level

(optional)

Determine the Highest Point of

Travel, and Draw Horizontal Line

for Header Bracket Placement

Add a 2 x 4 as a Structural Support

(If Necessary)

-In some installations it may be

necessary to install a 2x4 across

two studs to create a location for

header bracket or over drywall

Mark a spot on the “center of the

garage door” line, 2" (5 cm) above the

highest point of travel of the garage door

2" (5 cm)

Use lag screws (not provided)

to secure 2x4 (structural support) into

wood. Use concrete anchors to secure 2x4

into masonry.

Highest Point

of Travel

Download from Www.Somanuals.com. All Manuals Search And Download.

MOUNT THE HEADER BRACKET

Mark Bracket Holes

Drill Holes

Attach Bracket

Center bracket on the “center

of garage door” line and the

horizontal line made in Step 2.

Drill two 3/16"

pilot holes

Secure bracket

with lag screws

A14 Bracket

Mark the top

and bottom

Horizontal Line

bracket holes

C18 Lag Screw

Highest Point

of Travel

Center of

Garage Door

Ceiling Mount the Header Bracket (Optional)

NOTE: If your installation requires that the

header bracket be mounted to the ceiling. The

back edge of the bracket MUST NOT be

further than 6" (15 cm) from the header wall

and the arrow MUST point away from the

header wall.

Center the bracket

on the “center of

garage door” line

A14

Bracket

Use holes on

left and right side

to secure bracket

Attach Rail to the Header Bracket

A14 Header Bracket

Ring Fastener

A14

Ceiling Mount

Header

Bracket

A14

Header

Bracket

Ring Fastener

C11

Clevis Pin

C11

Clevis Pin

Mounting

Hole

Existing

Header Bracket

Mounting

Hole

Existing

Clevis Pin

NOTE: If the door spring

is in the way, you’ll need

help. Have someone hold

the opener securely on a

temporary support to allow

the rail to clear the spring.

Spacer

Mounting

Hole

Garage

Door

Option with

some pre-existing

installations

Opener Carton

ALL HARDWARE

SHOWN

ACTUAL SIZE

C11 Clevis Pin

C2 Spacer

C6 Ring Fastener

C18 Lag Screw

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

To avoid possible SERIOUS INJURY from a falling garage door

opener, fasten it securely to structural supports of the garage.

POSITION AND HANG MOTOR UNIT

Open Door to Full Open Position and Rest Rail

on a 2x4 to Position Opener at the Proper

Angle for Hanging from the Ceiling

CAUTION

To prevent damage to garage door, rest garage door opener

rail on 2 x 4 placed on top section of door.

2 x 4

If the top section or panel hits the trolley when you raise

the door, pull down on the trolley release arm to

disconnect inner and outer sections. Slide the outer trolley

toward the motor unit. The trolley can remain

disconnected until installation is completed.

NOTE: The garage door opener motor head will typically

sit lower than the header bracket, therefore, the rail will be

at an angle.

Attach Hanging Brackets to Ceiling and Fasten Motor Unit to Hanging Brackets

NOTE: Before the motor unit is secured to the ceiling, insure that the motor unit and rail are centered

over the door. If you mounted the header bracket off center, hang the motor unit the same distance.

Concrete anchors must be used if installing any brackets into masonry.

Option with finished or unfinished ceiling

Option with unfinished ceiling

Bracket

C8 Lag Screws or

(Not Provided)

Concrete Anchors (Not Provided)

(Not Provided)

C8 Lag Screws

Bolt 5/16"-18 x 7/8"

Lock Washer 5/16"

Measure

Distance

C9 Hex Bolt

C5 Lock Washer

C4 Nut

Nut 5/16" - 18

C9 Hex Bolt

C5 Lock Washer

C4 Nut

Remove

2 x 4

Remove 2x4 and Close Door

Close door

ALL HARDWARE SHOWN ACTUAL SIZE

C8 Lag Screw

C9 Hex Bolt

C4 Nut

C5 Lock Washer

Download from Www.Somanuals.com. All Manuals Search And Download.

CAUTION

To prevent damage to garage door, reinforce inside of door

with angle iron both vertically and horizontally.

HORIZONTAL AND VERTICAL REINFORCEMENT

Horizontal and vertical reinforcement (not provided) is

needed for light weight garage doors (fiberglass,

aluminum, steel, doors with glass panel, etc.).

Top of Door

Door

A horizontal reinforcement brace should be long

enough to be secured to two or three vertical

supports. A vertical reinforcement brace should cover

the height of the top panel. Contact your door

manufacturer for more information regarding

reinforcement of your door.

Bracket

Location

Hardware

Door Arm

(not provided)

Connects

Directly to

Vertical

Reinforcement

Many door reinforcement kits provide for direct

attachment of the clevis pin and door arm. In this

case, you will not need the door bracket; proceed to

Connect Door Arm to Trolley section.

FASTEN THE DOOR BRACKET

Position Door Bracket

Mark and Drill 3/16" Holes

Position the door bracket on

the face of the door within the

following limits:

1. The top edge of the bracket

2"-4" (5-10 cm) below the

top edge of the door.

2. The top edge of the bracket

directly below any structural

support across the top of

the door.

C15

Door Bracket

Center of

Garage Door

Fasten Door Bracket

Metal, insulated or lightweight

factory reinforced doors

Wood doors

Bolt

5/16" x 2"

ALL

HARDWARE

SHOWN

(Not Provided)

Center of

ACTUAL SIZE

Garage Door

C10 Self-Threading Screw

C10 Self-Threading

Center of

Garage Door

Screws

NOTE: The 1/4"-14 x 5/8" self-threading screws

are not intended for use on wood doors.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

To prevent possible SERIOUS INJURY or DEATH from a falling

garage door:

• If possible, use emergency release handle to disengage trolley ONLY

when garage door is CLOSED. Weak or broken springs or

unbalanced door could result in an open door falling rapidly and/or

unexpectedly.

• NEVER use emergency release handle unless garage doorway is

clear of persons and obstructions.

ATTACH DOOR TO TROLLEY

Attach Emergency Release Rope and Handle

Secure handle with overhand knot

and heat seal rope.

• NEVER use handle to pull door open or closed. If rope knot

becomes untied, you could fall.

ENGAGED

NOTE: Handle should hang 6 feet (1.5 m) above floor.

Ensure that the rope and handle clear the tops of all

vehicles to avoid entanglement.

C19 Rope

C20 Emergency

Release Handle

Overhand

Knot

RELEASED

CONNECT DOOR ARM TO TROLLEY

Pull Emergency Release Rope to Disengage

the Trolley

Slide Trolley Back 2" (5 cm) and Connect Straight

Door Arm to the Trolley

2" (5 cm)

Ring

Fastener

Pull Down

to Release

Trolley

Connect

Straight

C21

Door Arm

Clevis Pin

to Trolley

Straight

Door Arm

Connect Curved Door Arm to the Door Bracket

Ensure Door is Fully Closed and Connect

Door Arms

Ring

Fastener

Connect Curved

Nut

Door Arm to

Lock

Door Bracket

Washer

Straight

Door Arm

Curved

Clevis Pin

Door Arm

C9 Hex Bolt

Curved

Door Arm

ALL HARDWARE SHOWN ACTUAL SIZE

C21 Clevis Pin

C5 Lock Washer

C4 Nut

C9 Hex Bolt

C6 Ring Fastener

C7 Clevis Pin

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

To prevent possible SERIOUS INJURY or DEATH from

electrocution:

• Be sure power is not connected BEFORE installing Door

Control.

INSTALLING THE DOOR CONTROL

• Connect ONLY to 24 VOLT low voltage circuit.

To prevent possible SERIOUS INJURY or DEATH from a closing

garage door:

• Install Door Control within sight of garage door, out of reach

of children at a minimum height of 5 feet (1.5 m), and away

from all moving parts of door.

• NEVER permit children to operate or play with door control

push buttons or remote control transmitters.

• Activate door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed.

NEVER permit anyone to cross path of closing garage door.

Strip Door Control

Connect Wire to

Door Control

Wire

Strip

7/16" (11 mm)

Insulation

Wire

A21

Door Control:

Door Control

White

Wire

Multi-Function

Button

Terminal

Screws

White Wire

WHT

RED

Red/White

Wire

Terminal

Screws

Red/White Wire

Position Door Control, Route Door Control Wire to

Motor Unit and Secure with Insulated Staples.

Permanently Mount 2 Safety Labels Using Adhesive

Backing, Tacks or Staples, If Necessary.

Carefully Remove Cover

Multi-Function Door

Controls ONLY

Insulated

Door Control

Wire

Staple

Insulated Staple

LOCK

LIGH

5 FEET (1.5 m)

MINIMUM

Do NOT strip any

insulation from

the staples

Attach Door Control to Wall and Replace Cover

Connect Door Control Wires

Multi-Function Door Control

Door Control Button

Single

to Motor Unit

C15

Red

C13

Screw

Gang Box

Drywall

C12

Screw

24V Circuit

Terminal

Anchors

Red/White

White

Wire

Terminal

C15

C12

Drywall

White

Wire

Screw

Anchors

LOCK

LIGHT

LIGH

C13

Screw

C12

Screw

To release or

insert wire,

push in tab with

screwdriver.

Multi-Function Door Control:

If, No Gang Box is Present

Multi-Function Door Control:

Gang Box Installation

ALL HARDWARE SHOWN ACTUAL SIZE

C12 Screw

C15 Drywall Anchors

C13 Screw

C1 InCsu1laStetadplSestaples

Download from Www.Somanuals.com. All Manuals Search And Download.

CAUTION

To prevent possible OVERHEATING of the endpanel or

light socket:

• DO NOT use short neck or specialty light bulbs.

• DO NOT use halogen bulbs. Use ONLY incandescent.

INSTALLING THE LIGHT BULB(S)

To prevent damage to the opener:

• DO NOT use bulbs larger than 100W.

• ONLY use A19 size bulbs.

Flex Sides of Light Lens to

Remove Lens from Tabs

Rotate Light Lens Down

Install Standard Light Bulb(s)

(100W max) into Socket(s)

100 Watt (Max)

Standard Light Bulb

WARNING

To prevent possible SERIOUS INJURY or DEATH from

electrocution or fire:

ELECTRICAL REQUIREMENTS

• Be sure power is NOT connected to the opener, and

disconnect power to circuit BEFORE removing cover to

establish permanent wiring connection.

Plug Motor Unit into Power Outlet

• Garage door installation and wiring MUST be in compliance

with ALL local electrical and building codes.

• NEVER use an extension cord, 2-wire adapter, or change plug

in ANY way to make it fit outlet. Be sure the opener is

grounded.

RIGHT

WRONG

NOTE: Plug motor unit into grounded power outlet. If a grounded outlet is not available, contact a qualified

electrician to install a proper outlet.

If permanent wiring is required by your local code, follow procedure below. Disconnect power to the

circuit before removing cover to establish permanent wiring connections.

Remove Motor Unit

Screws and Cover

Remove Power

Cord

Run Wire from

Outlet to Motor Unit

Replace Motor Unit

Cover and Screws

ECTION

round Tab

d Wire

Black

Wire

Ground Wire

Black

Wire

White Wire

Black Wire

White Wire

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

To prevent SERIOUS INJURY or DEATH from a closing garage

door:

• Correctly connect and align the safety reversing sensor. This

required safety device MUST NOT be disabled.

INSTALL THE PROTECTOR SYSTEM

• Install the safety reversing sensor so beam is NO HIGHER

than 6" (15 cm) above garage floor.

The safety reversing sensor must be connected and

aligned correctly before the garage door opener will

move in the down direction.

NOTE: DO NOT operate the opener at this time.

IMPORTANT INFORMATION ABOUT THE SAFETY

REVERSING SENSOR

If it is necessary to mount the units on the wall, the

brackets must be securely fastened to a solid surface

such as the wall framing. Extension brackets (see

accessories) are available if needed. If installing in

masonry construction, add a piece of wood at each

location to avoid drilling extra holes in masonry if

repositioning is necessary.

When properly connected and aligned, the sensor will

detect an obstacle in the path of its electronic beam. The

sending eye (with an amber indicator light) transmits an

invisible light beam to the receiving eye (with a green

indicator light). If an obstruction breaks the light beam

while the door is closing, the door will stop and reverse to

full open position, and the opener lights will flash 10 times.

The invisible light beam path must be unobstructed. No

part of the garage door (or door tracks, springs, hinges,

rollers or other hardware) may interrupt the beam while

the door is closing.

The units must be installed inside the garage so that the

sending and receiving eyes face each other across the

door, no more than 6" (15 cm) above the floor. Either can

be installed on the left or right of the door as long as the

sun never shines directly into the receiving eye lens.

The mounting brackets are designed to clip onto the track

of sectional garage doors without additional hardware.

Safety Reversing

Sensor no higher

than 6" (15 cm)

above floor

Safety Reversing

Sensor no higher

than 6" (15 cm)

above floor

Invisible Light Beam

Protection Area

Facing the door from inside the garage

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALL THE PROTECTOR SYSTEM

Assemble Safety Reversing Sensors

Mount Brackets

Garage door track installation (preferred)

A17

Safety Reversing

Sensor

Door

Track

Indicator

Lens Light

A17

Safety Reversing

Sensor

C14

Carriage

Sensor Beam

No Higher

Bolts

Than 6" (15cm)

Above Floor

A10

Safety Sensor

C14

Wing Nut

Bracket

Mount Brackets: Mounting Options

Floor installation (optional)

Wall installation (optional)

Wall installation with Extension

Brackets (optional)

Inside Garage Wall

Extension Bracket

Inside

arage

Attach with

(Provided with

Fasten 2x4 to

concrete anchors

(not provided)

Extension Bracket)

Wall with Lag

Screws (Not

Provided)

Sensor Beam

No Higher Than

6" (15 cm)

Sensor Beam

No Higher

Than 6" (15 cm)

Above Floor

Than 6" (15 cm)

Above Floor

Lag Screws

(Provided with

(Not Provided)

Extension Bracket)

NOTE: The safety reversing sensor must

be connected and aligned correctly before

the garage door opener will move in the

down direction.

Safety Reversing Sensors

MUST be aligned and no

higher than 6" (15 cm)

above floor

Safety Reversing Sensors

MUST be aligned and no

higher than 6" (15 cm)

above floor

ALL HARDWARE SHOWN ACTUAL SIZE

C16 Wing Nut

C14 Carriage Bolt

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRE SAFETY REVERSING SENSOR

Run Safety Sensor Wire to Motor Unit and Secure

with Insulated Staples

Safety Sensor Wire

Insulated Staple

Safety Sensor Wire

Insulated Staple

Do NOT strip any

insulation from

the staples

Safety Reversing Sensor

Sensor

Safety Reversing Sensor

Sensor

Strip All Safety Sensor

Wires

Separate the Black/White

and the White Wires

Twist Like Colored Wires

Together

Strip

7/16" (11 mm)

Insulation

Wire

Black/White

Wire

White

Wire

Black/White

Wires

White

Wires

Connect Safety Sensors to Motor Unit

Locate the quick connect terminals

on your garage door opener, they are

located on back panel.

Insert the two white wires into the white

quick connect terminal and insert the

two black/white wires into the grey quick

connect terminal

White

Wires

Black/White

Wires

Grey

ALL HARDWARE SHOWN

ACTUAL SIZE

Terminal

C1 Staples

Screwdriver

White

Terminal

To release or insert wire,

push in tab with screwdriver.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

ADJUSTMENT

Without a properly installed safety reversal system, persons

(particularly small children) could be SERIOUSLY INJURED or

KILLED by a closing garage door.

• Incorrect adjustment of garage door travel limits will interfere

with proper operation of safety reversal system.

• If one control (force or travel limits) is adjusted, the other

control may also need adjustment.

• After ANY adjustments are made, the safety reversal system

must be tested. Door must reverse on contact with 1-1/2"

(3.8 cm) high object (or 2 x 4 laid flat) on floor.

ADJUSTMENT STEP 1

ADJUST THE UP AND DOWN TRAVEL LIMITS

Limit adjustment settings regulate the points at which the

door will stop when moving up or down.

To operate the opener, press the door control push bar.

Run the opener through a complete travel cycle.

• Does the door open and close completely?

CAUTION

• Does the door stay closed and not reverse

unintentionally when fully closed?

To prevent damage to vehicles, be sure fully open door

provides adequate clearance.

If your door passes both of these tests, no limit

adjustments are necessary unless the reversing test fails

(see Adjustment Step 3).

Cover Protection Bolt

Adjustment procedures are outlined below. Read the

procedures carefully before proceeding to Adjustment Step

2. Use a screwdriver to make limit adjustments. Run the

opener through a complete travel cycle after each

adjustment.

2-4"

(5 cm-

10 cm)

NOTE: Repeated operation of the opener during

adjustment procedures may cause the motor to overheat

and shut off. Simply wait 15 minutes and try again.

NOTE: If anything interferes with the door’s upward travel,

it will stop. If anything interferes with the door’s downward

travel (including binding or unbalanced doors), it will

reverse.

Limit Adjustment Screws

Left Side Panel

ADJUSTMENT LABEL

HOW AND WHEN TO ADJUST THE LIMITS

Turn either limit adjustment screw the direction

of the arrow to increase trolley travel, turn in

the opposite direction to decrease travel

• If the door does not open completely but opens at

least 5 feet (1.5 m):

Increase up travel. Turn the UP limit adjustment screw

clockwise. One turn equals 2" (5 cm) of travel.

• If the opener reverses in fully closed position:

NOTE: To prevent the trolley from hitting the cover

protection bolt, keep a minimum distance of 2-4"

(5-10 cm) between the trolley and the bolt.

Decrease down travel. Turn the DOWN limit adjustment

screw clockwise. One turn equals 2" (5 cm) of travel.

• If the door reverses when closing and there is no

visible interference to travel cycle:

• If door does not open at least 5 feet (1.5 m):

Adjust the UP (open) force as explained in Adjustment

Step 2.

If the opener lights are flashing, the Safety Reversing

Sensors are either not installed, misaligned, or

obstructed.

• If the door does not close completely:

Increase down travel. Turn the DOWN limit adjustment

screw counterclockwise. One turn equals 2" (5 cm) of

travel.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

Without a properly installed safety reversal system, persons

(particularly small children) could be SERIOUSLY INJURED or

KILLED by a closing garage door.

ADJUSTMENT STEP 2

• Too much force on garage door will interfere with proper

operation of safety reversal system.

ADJUST THE FORCES

• NEVER increase force beyond minimum amount required to

close garage door.

• NEVER use force adjustments to compensate for a binding or

sticking garage door.

Force adjustment controls are located on the back panel

of the motor unit. Force adjustment settings regulate the

amount of power required to open and close the door.

If the forces are set too light, door travel may be

interrupted by nuisance reversals in the down direction

and stops in the up direction. Weather conditions can

affect the door movement, so occasional adjustment may

be needed.

• If one control (force or travel limits) is adjusted, the other

control may also need adjustment.

• After ANY adjustments are made, the safety reversal system

must be tested. Door must reverse on contact with 1-1/2"

(3.8 cm) high object (or 2 x 4 laid flat) on floor.

The maximum force adjustment range is about 3/4 of a

complete turn. Do not force controls beyond that point.

Turn force adjustment controls with a screwdriver.

NOTE: If anything interferes with the door’s upward travel,

it will stop. If anything interferes with the door’s downward

travel (including binding or unbalanced doors), it will

reverse.

Force Adjustment

Controls

HOW AND WHEN TO ADJUST THE FORCES

1. Test the DOWN (close) force

• Grasp the door bottom when the door is about halfway

through DOWN (close) travel. The door should reverse.

Reversal halfway through down travel does not

guarantee reversal on a 1-1/2" (3.8 cm) obstruction. See

Adjustment Step 3, page 22. If the door is hard to

hold or doesn’t reverse, decrease the DOWN (close)

force by turning the control counterclockwise. Make

small adjustments until the door reverses normally. After

each adjustment, run the opener through a complete

cycle.

Back Side Panel

FORCE ADJUSTMENT LABEL

• If the door reverses during the down (close) cycle

and the opener lights aren’t flashing, increase DOWN

(close) force by turning the control clockwise. Make

small adjustments until the door completes a close

cycle. After each adjustment, run the opener through a

complete travel cycle. Do not increase the force beyond

the minimum amount required to close the door.

Open Force

Force Settings:

1 = Lowest Force

9 = Maximum Force

Close Force

2. Test the UP (open) force

• Grasp the door bottom when the door is about halfway

through UP (open) travel. The door should stop. If the

door is hard to hold or doesn’t stop, decrease UP

(open) force by turning the control counterclockwise.

Make small adjustments until the door stops easily and

opens fully. After each adjustment, run the opener

through a complete travel cycle.

• If the door doesn’t open at least 5 feet (1.5 m),

increase UP (open) force by turning the control

clockwise. Make small adjustments until door opens

completely. Readjust the UP limit if necessary. After

each adjustment, run the opener through a complete

travel cycle.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

Without a properly installed safety reversal system, persons

(particularly small children) could be SERIOUSLY INJURED or

KILLED by a closing garage door.

ADJUSTMENT STEP 3

• Safety reversal system MUST be tested every month.

• If one control (force or travel limits) is adjusted, the other

control may also need adjustment.

TEST THE SAFETY REVERSAL SYSTEM

Test

• After ANY adjustments are made, the safety reversal system

must be tested. Door must reverse on contact with 1-1/2"

(3.8 cm) high object (or 2 x 4 laid flat) on the floor.

• With the door fully open, place a 1-1/2" (3.8 cm) board

(or a 2 x 4 laid flat) on the floor, centered under the

garage door.

• Operate the door in the down direction. The door must

reverse on striking the obstruction.

Adjust

• If the door stops on the obstruction, it is not traveling far

enough in the down direction. Increase the down travel

by turning the DOWN limit adjustment screw

counterclockwise 1/4 turn.

NOTE: On a sectional door, make sure limit adjustments

do not force the door arm beyond a straight up and

down position. See page 14.

1-1/2" (3.8 cm) board (or a 2x4 laid flat)

• Repeat the test.

• When the door reverses on the 1-1/2" (3.8cm) (or a 2x4

laid flat) board, remove the obstruction and run the

opener through 3 or 4 complete travel cycles to test

adjustment.

TEST THE PROTECTOR SYSTEM

• Press the remote control push button to open the door.

• Place the opener carton in the path of the door.

WARNING

Without a properly installed safety reversing sensor, persons

(particularly small children) could be SERIOUSLY INJURED or

KILLED by a closing garage door.

• Press the remote control push button to close the door.

The door will not move more than an inch, and the

opener lights will flash.

The garage door opener will not close from a remote if the

indicator light in either sensor is off (alerting you to the fact

that the sensor is misaligned or obstructed).

If the opener closes the door when the safety reversing

sensor is obstructed (and the sensors are no more than

6" (25 mm) above the floor), call for a trained door

systems technician.

Safety Reversing Sensor

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.

9. If one control (force or travel limits) is adjusted, the other

control may also need adjustment.

10. After ANY adjustments are made, the safety reversal system

MUST be tested.

2. ALWAYS keep remote controls out of reach of children. NEVER

permit children to operate or play with garage door control

push buttons or remote controls.

3. ONLY activate garage door when it can be seen clearly, it is

properly adjusted, and there are no obstructions to door travel.

4. ALWAYS keep garage door in sight until completely closed. NO

ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.

5. NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY OPEN

DOOR.

6. If possible, use emergency release handle to disengage trolley

ONLY when garage door is CLOSED. Weak or broken springs

or unbalanced door could result in an open door falling rapidly

and/or unexpectedly.

11. Safety reversal system MUST be tested every month. Garage

door MUST reverse on contact with 1-1/2" (3.8 cm) object

(or a 2 x 4 laid flat) on the floor.

12. ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED (see

page 2). An improperly balanced door may NOT reverse

when required and could result in SEVERE INJURY or

DEATH.

13. ALL repairs to cables, spring assemblies and other hardware,

ALL of which are under EXTREME tension, MUST be made

by a trained door systems technician.

14. ALWAYS disconnect electric power to garage door opener

BEFORE making ANY repairs or removing covers.

7. NEVER use emergency release handle unless garage doorway

is clear of persons and obstructions.

8. NEVER use handle to pull garage door open or closed. If rope

knot becomes untied, you could fall.

15.

SAVE THESE INSTRUCTIONS.

USING YOUR GARAGE DOOR OPENER

6. If obstructed while opening, the door will stop.

7. If fully open, the door will not close when the safety

sensor beam is broken. The safety sensor has no effect

in the opening cycle.

Your Security✚^®opener and hand-held remote control

have been factory-set to a matching code which changes

with each use, randomly accessing over 100 billion new

codes. Your opener will operate with up to eight

Security✚^®remote controls and one Security✚^®Keyless

Entry System. If you purchase a new remote, or if you

wish to deactivate any remote, follow the instructions in

the Programming section.

If the safety sensor is not installed, or is misaligned, the

door won’t close from a hand-held remote. However, you

can close the door with the Door Control, the Outside

Keylock, or Keyless Entry, if you activate them until down

travel is complete. If you release them too soon, the door

will reverse.

Activate your opener with any of the following:

The opener lights will turn on under the following

conditions: when the opener is initially plugged in; when

power is restored after interruption; when the opener is

activated.

• The hand-held Remote Control: Hold the push button

down until the door starts to move.

• The wall-mounted Door Control: Hold the push button or

bar down until the door starts to move.

They will turn off automatically after 4-1/2 minutes or

provide constant light when the Light feature on the

Multi-Function Door Control is activated. Bulb size is A19.

Bulb power is 100 watts maximum.

• The Keyless Entry (See Accessories): If provided with

your garage door opener, it must be programmed before

use. See Programming.

Security✚^®light feature: Lights will also turn on when

someone walks through the open garage door. With a

Multi-Function Door Control, this feature may be turned off

as follows: with the opener lights off, press and hold the

light button for 10 seconds, until the light goes on, then off

again. To restore this feature, start with the opener lights

on, then press and hold the light button for 10 seconds

until the light goes off, then on again.

When the opener is activated (with the safety

reversing sensor correctly installed and aligned)

1. If open, the door will close. If closed, it will open.

2. If closing, the door will reverse.

3. If opening, the door will stop.

4. If the door has been stopped in a partially open position,

it will close.

5. If obstructed while closing, the door will reverse. If the

obstruction interrupts the safety sensor beam, the

opener lights will blink for five seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE WALL-MOUNTED DOOR CONTROL

CARE OF YOUR OPENER

Push

Bar

The Multi-Function Door Control

Limit and Force Adjustments

LIMIT CONTROLS

Lock

Press the push bar/push button to open or

close the door. Press again to reverse the

door during the closing cycle or to stop the

door while it’s opening.

Weather conditions may cause some

minor changes in door operation requiring

some readjustments, particularly during

the first year of operation.

Button

LOCK

LIGHT

Light

Button

Open Force Close Force

FORCE CONTROLS

Push

Button

Light Feature

Pages 20 and 21 refer to the limit and

force adjustments. Only a screwdriver is

required. Follow the instructions carefully.

Press the Light button to turn the opener

light on or off. It will not control the opener

lights when the door is in motion. If you turn it on and then

activate the opener, the light will remain on for 4-1/2

minutes. Press again to turn it off sooner. The 4-1/2 minute

interval can be changed to

Repeat the safety reverse test (page 22) after any

adjustment of limits or forces.

Maintenance Schedule

Once a Month

1-1/2, 2-1/2, or 3-1/2 minutes as follows:

• Manually operate door. If it is unbalanced or binding, call

a trained door systems technician.

1. Press and hold the Lock button until the light blinks

(about 10 seconds). A single blink indicates that the

timer is reset to 1-1/2 minutes.

• Check to be sure door opens and closes fully. Adjust

limits and/or force if necessary.

2. Repeat the procedure and the light will blink twice,

resetting the timer to 2-1/2 minutes.

• Repeat the safety reverse test. Make any necessary

adjustments.

3. Repeat again for a 3-1/2 minute interval, etc., up to a

maximum of four blinks and 4-1/2 minutes.

Twice a Year

• Check chain tension. Disconnect trolley first. Adjust if

necessary.

Lock Feature

Designed to prevent operation of the door from hand-held

remote controls. However, the door will open and close

from the Door Control, the Outside Keylock and the

Keyless Entry Accessories.

Once a Year

• Oil door rollers, bearings and hinges. The opener does

not require additional lubrication. Do not grease door

tracks.

To activate, press and hold the Lock button for 2 seconds.

The push bar light will flash as long as the Lock feature

is on.

To turn off, press and hold the Lock button again for

2 seconds.The push bar light will stop flashing. The Lock

feature will also turn off whenever the “Learn” button on

the motor unit panel is activated.

WARNING

To prevent possible SERIOUS INJURY or DEATH from a falling

garage door:

• If possible, use emergency release handle to disengage

trolley ONLY when garage door is CLOSED. Weak or broken

springs or unbalanced door could result in an open door

falling rapidly and/or unexpectedly.

TO OPEN THE DOOR MANUALLY

The door should be fully closed if possible. Pull down on

the emergency release handle and lift the door manually.

To reconnect the door to the opener, press the door

control push bar.

• NEVER use emergency release handle unless garage

doorway is clear of persons and obstructions.

The lockout feature prevents the trolley from reconnecting

automatically, pull the emergency release handle down

and back (toward the opener). The door can then be

raised and lowered manually as often as necessary. To

disengage the lockout feature, pull the handle straight

down. The trolley will reconnect on the next UP or DOWN

operation.

• NEVER use handle to pull door open or closed. If rope knot

becomes untied, you could fall.

Trolley

Release

Arm

Trolley

Release Arm B9

(In Manual

Emergency

Disconnect

Position)

Release Handle B9

(Down and Back)

Manual disconnect position

Lockout position

Download from Www.Somanuals.com. All Manuals Search And Download.

HAVING A PROBLEM?

Bell Wire

Sending Eye

Safety Sensor

(Amber Indicator

Light)

Receiving Eye

Safety Sensor

(Green Indicator

Light)

“Learn”

Button

LED or

Diagnostic

LED

Safety Reversing Sensor

1. My door will not close and the light bulbs blink on

my motor unit: The safety reversing sensor must be

connected and aligned correctly before the garage

door opener will move in the down direction.

5. My lights will not turn off when door is open:

• The garage door opener is equipped with a security

light feature. This feature activates the light on

when the safety sensor beam has been obstructed.

Refer to Operation section; Using the Wall Mounted

Door Control, Light Feature.

• Verify the safety sensors are properly installed,

aligned and free of any obstructions. Refer to

Installation Step, Install The Protector System^®.

6. My motor unit hums briefly:

• Check diagnostic LED for flashes on the motor unit

then refer to the Diagnostic Chart on the following

page.

• First verify that the trolley is against the stop bolt.

• Release the door from the opener by pulling the

Emergency Release Rope.

2. My remotes will not activate the door:

• Manually bring the door to a closed position.

• Verify your Multi-Function door control is not

blinking. If it is blinking, deactivate the Lock Mode

following the instructions for Using the

Multi-Function Door Control.

• Loosen the chain by adjusting the outer nut 4 to 5

turns. This relieves the tension.

• Run the motor unit from the remote control or door

control. The trolley should travel towards the door

and stop. If the trolley re-engages with the door,

pull the Emergency Release Rope to disengage.

• Reprogram remotes following the programming

instructions. Refer to Programming.

• If remote will still not activate your door, check

diagnostic LED for flashes on motor unit then refer

to Diagnostic Chart on the following page.

• Decrease the up travel by turning the UP Travel

adjustment screw 2 full turns away from the arrow.

• If the trolley does not move away from the bolt,

repeat the steps above.

3. My door reverses for no apparent reason: Repeat

safety reverse test after adjustments to force or travel

limits. The need for occasional adjustment for the

force and limit settings is normal. Weather conditions

in particular can affect door travel.

7. My motor unit clicks:

• Motor is overheated. Allow 15 minutes for motor to

cool and try again.

• Manually check door for balance or any binding

problems.

• Refer to Adjustment Step 2, Adjust the Forces.

4. My door reverses for no apparent reason after

fully closing and touching the floor: Repeat safety

reverse test after adjustments to force or travel limits.

The need for occasional adjustment for the force and

limit settings is normal. Weather conditions in

particular can affect door travel.

• Refer to Adjustment Step 1, Adjust the UP and

DOWN Travel Limits. Decrease down travel by

turning DOWN limit adjustment screw clockwise.

Download from Www.Somanuals.com. All Manuals Search And Download.

DIAGNOSTIC CHART

Your garage door opener is programmed with

self-diagnostic capabilities. The “Learn” button/diagnostic

LED will flash a number of times then pause signifying it

has found a potential issue. Consult the Diagnostic

Chart below.

Bell Wire

Diagnostics

Located On

Motor Unit

Installed Safety

LED or

Diagnostic

LED

Reversing Sensor

“Learn”

Button

Safety Reversing Sensor

1 FLASH

Symptom: One or both of the Indicator lights on the safety sensors do

not glow steady.

Safety reversing

sensors wire shorted

or black/white wire

reversed.

• Inspect sensor wires for a short (staple in wire), correct wiring polarity

(black/white wires reversed), broken or disconnected wires, replace/attach

as needed.

• Disconnect all wires from back of motor unit.

2 FLASHES

• Remove sensors from brackets and shorten sensor wires to 1-2 ft

(30-60 cm) from back each of sensor.

• Reattach sending eye to motor unit using shortened wires. If sending eye

indicator light glows steadily, attach the receiving eye.

Safety reversing

sensors wire open

(broken or

• Align sensors, if the indicator lights glow replace the wires for the sensors. If

the sensor indicator lights do not light, replace the safety sensors.

disconnected).

3 FLASHES

Symptom: LED is not lit on door control.

• Inspect door control/wires for a short (staple in wire), replace as needed.

Door control or

wire shorted.

• Disconnect wires at door control, touch wires together. If motor unit

activates, replace door control.

• If motor unit does not activate, disconnect door control wires from motor

unit. Momentarily short across red and white terminals with jumper wire. If

motor unit activates, replace door control wires.

• If motor unit doesn’t operate, motor unit is overheated. Wait 15 minutes and

retry. If motor unit still will not operate replace logic board.

4 FLASHES

Symptom: Sending indicator light glows steadily, receiving indicator light

is dim or flashing.

Safety Reversing

Sensors slightly

misaligned (dim or

flashing LED).

• Realign receiving eye sensor, clean lens and secure brackets.

• Verify door track is firmly secured to wall and does not move.

5 FLASHES

Symptom: Motor has overheated; the motor unit does not operate or

trolley is stuck on stop bolt = Motor unit hums briefly; RPM Sensor =

Short travel 6-8" (15-20 cm).

Motor overheated

or possible RPM

sensor failure.

• Unplug unit to reset. Try to operate motor unit, check diagnostic code.

• If it is still flashing 5 times and motor unit moves 6-8" (15-20 cm), replace

RPM sensor.

Unplug to reset.

6 FLASHES

Symptom: Motor unit doesn’t operate.

• Replace logic board because motor rarely fails.

Motor Circuit Failure.

Replace Receiver

Logic Board.

Download from Www.Somanuals.com. All Manuals Search And Download.

PROGRAMMING

TO ADD OR REPROGRAM AN ADDITIONAL HAND-HELD REMOTE CONTROL

NOTICE: If this Security✚^®garage door opener is operated with a non-rolling code transmitter, the technical measure in

the receiver of the garage door opener, which provides security against code-theft devices, will be circumvented. The

owner of the copyright in the garage door opener does not authorize the purchaser or supplier of the non-rolling code

transmitter to circumvent that technical measure.

Your garage door opener has already been programmed at the factory to operate with your hand-held remote control.

The door will open and close when you press the push button.

Below are instructions for programming your opener to operate with additional Security✚^®remote controls.

Using the “Learn” Button

Using the Multi-Function Door Control

LOCK

LIGHT

1. Press and hold the button on the

hand-held remote* that you wish to

operate your garage door.

1. Press and release the “learn” button on

the motor unit. The learn indicator light

will glow steadily for 30 seconds.

2. While holding the remote button, press

and hold the light button on the

Multi-Function Door Control.

LOCK

LIGHT

2. Within 30 seconds, press and hold the

button on the hand-held remote* that

you wish to operate your garage door.

3. Continue holding both buttons while you

press the push bar on the Multi-Function

Door Control (all three buttons are held).

3. Release the button when the motor

unit lights blink. It has learned the

code. If light bulbs are not installed,

two clicks will be heard.

LOCK

LIGHT

4. Release buttons when the motor unit

lights blink. It has learned the code. If

light bulbs are not installed, two clicks

will be heard.

TO CONTROL THE OPENER LIGHTS

*3-BUTTON REMOTES

Only available with Multi-Function Door Control:

If provided with your garage door opener, the large

button is factory programmed to operate it. Additional

buttons on any Security✚^®

In addition to operating the door, you may

program the remote to operate the lights.

multi-function remote or

mini-remote can be

1. With the door closed, press and hold a

small remote button that you want to control

the light.

programmed to operate

other Security✚^®

2. Press and hold the Light button on the Multi-Function

door control.

garage door openers.

3. While holding the Light button, press and hold the Lock

button on the door control.

4. After the opener lights flash, release all buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

TO ADD, REPROGRAM OR CHANGE A KEYLESS ENTRY PIN

NOTE: Your new Keyless Entry must be programmed to operate your garage door opener.

Using the “Learn” Button

Using the Multi-Function Door Control

LOCK

LIGHT

NOTE: This method requires two people if the Keyless

Entry is already mounted outside the garage.

1. Press and release the “learn” button

on motor unit. The learn indicator light

will glow steadily for 30 seconds.

1. Enter a four digit personal identification

number (PIN) of your choice on the

keypad. Then press and hold enter.

2. Within 30 seconds, enter a four digit

personal identification number (PIN) of

your choice on the keypad. Then press

and hold the enter button.

2. While holding the ENTER button, press

and hold the LIGHT button on the

Multi-Function Door Control.

LOCK

LIGHT

3. Continue holding the ENTER and LIGHT

buttons while you press the push bar on

the Multi-Function Door Control (all three

3. Release the button when the motor

unit lights blink. It has learned the

code. If light bulbs are not installed,

two clicks will be heard.

LOCK

LIGHT

buttons are held).

4. Release buttons when the motor unit

lights blink. It has learned the code. If

light bulbs are not installed, two clicks

will be heard.

TO CHANGE AN EXISTING, KNOWN PIN

If the existing PIN is known, it may be changed by one

person without using a ladder.

PRS

TUV

WXY

1. Press the four buttons for the present PIN, then press

and hold the # button.

ENTER

The opener light will blink twice. Release the # button.

2. Press the new 4-digit PIN you have chosen, then

press Enter.

The motor unit lights will blink once when the PIN has

been learned.

Test by pressing the new PIN, then press Enter. The door

should move.

Download from Www.Somanuals.com. All Manuals Search And Download.

TO SET A TEMPORARY PIN

You may authorize access by visitors or service people

3. To set the number of hours this temporary PIN will work,

press the number of hours (up to 255), then press ✽.

with a temporary 4-digit PIN. After a programmed number

of hours or number of accesses, this temporary PIN

expires and will no longer open the door. It can be used to

close the door even after it has expired. To set a

temporary PIN:

3. To set the number of times this temporary PIN will work,

press the number of times (up to 255), then press #.

The opener light will blink once when the temporary PIN

has been learned.

1. Press the four buttons for your personal entry PIN

(not the last temporary PIN), then press and hold

the ✽ button.

Test by pressing the four buttons for the temporary PIN,

then press Enter. The door should move. If the temporary

PIN was set to a certain number of openings, remember

that the test has used up one opening.To clear the

temporary password, repeat steps 1-3, setting the number

of hours or times to 0 in step 3.

The opener light will blink three times. Release the

button.

2. Press the temporary 4-digit PIN you have chosen, then

press Enter.

The opener light will blink four times.

One Button Close: Opener can be closed by pressing only the ENTER button if the one button close feature has been

activated. This feature has been activated at the factory. To activate or deactivate this feature press and hold buttons 1

and 9 for 10 seconds. The keypad will blink twice when the one button close is active. The keypad will blink four times

when one button close is deactivated.

TO ERASE ALL CODES FROM MOTOR UNIT MEMORY

To deactivate any unwanted remote, first erase all codes:

Press and hold the “learn” button on motor unit until the

learn indicator light goes out (approximately 6 seconds).

All previous codes are now erased. Reprogram each

remote or keyless entry you wish to use.

WARNING

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

To reduce risk of fire, explosion or chemical burn:

THE REMOTE CONTROL BATTERY

To replace battery, use the

visor clip or screwdriver blade

to pry open the case as

shown. Insert battery positive

side up (+).

• Replace ONLY with 3V2032 coin batteries.

• Do NOT recharge, disassemble, heat above 100°C (212°F) or

incinerate.

Battery

positive

side up (+)

Dispose of old battery properly.

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications

of this receiver and/or transmitter are prohibited, except for changing the code setting or

replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

Replace the battery with only

3V2032 coin cell batteries.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS

RAIL ASSEMBLY PARTS

KEY PART

NO. NO.

DESCRIPTION

4A1008

Master link kit

41C5141-1 Complete trolley assembly

183C158-13 Rail - front (header) section

183C157-9 Rail - center/back section

144C56

41A5807

12D598-1

Chain idler pulley

Chain and cable

“U” bracket

NOT SHOWN

183A163

19A47

Wear pads

Cover protection bolt spacer

INSTALLATION PARTS

KEY PART

NO. NO.

DESCRIPTION

41C494-2

950D

953D

10A20

29B137

41A2828

Multi-function door control panel

Single-button remote control

3-button remote control

3V2032 Lithium battery

Transmitter visor clip

Emergency release rope and handle

assembly

LOCK

LIGHT

41B4494-1 2-conductor bell wire – white and

white/red

41A5047-2 Header bracket with clevis pin and

fastener

41A5047-1 Door bracket with clevis pin and

fastener

178B35

178B34

12B776

41A5034

Curved door arm section

Straight door arm section

Hanging bracket

Safety sensor kit (receiving and

sending eyes) with 3'(.9 m)

2-conductor bell wire attached

41A5266-1 Safety sensor brackets (2)

41A4166

Door Control Button

NOT SHOWN

41A5258-11 Installation hardware bag

114A3165

114A3163

Assembly/installation manual

Installation instructions for one-piece

doors

Download from Www.Somanuals.com. All Manuals Search And Download.

MOTOR UNIT ASSEMBLY PARTS

(Down)

Contact

LIMIT SWITCH

ASSEMBLY

Brown

Wire

D N

Grey

Wire

U P

Drive

Gear

Center Limit

Contact

(Up)

Contact

Yellow

Wire

KEY PART

NO. NO.

NO.

DESCRIPTION

41A5615

Chain Spreader

41D3058 Universal replacement motor and

bracket assembly

41C4220A Gear and sprocket assembly

Complete with: Motor, worm, bracket,

bearing assembly, RPM sensor

Complete with: Spring washer, thrust

washer, retaining ring, bearing plate,

roll pins (2), drive gear and worm gear, 14

41A2818 Limit switch drive and retainer

41A2822-1 Interrupter cup assembly

41C4398A RPM sensor assembly

41AC050-1 Receiver logic board assembly

(PD210D/PD212D/248730)

helical gear with retainer and grease

41A2817

41B4245

Drive/worm gear kit with grease,

roll pins (2)

Line cord

41A5484-1 End panels with all labels

(PD610D/PD612D/PD612KLD/7920KD

41AC050-2 Receiver logic board assembly

(PD610D/PD612D/PD612KLD/7920KD

48930D) Complete with: Logic

board,end panel with all labels, light

socket

48930D)

End panels with all labels

(PD210D/PD212D/248730)

41D181

4A1344

108D79

30B532

12A373

41A3150

Light socket

Lens

1/2 hp Capacitor

Capacitor bracket

Terminal block with screws

41C5497 High voltage wire harness assembly

41C5498 Low voltage wire harness assembly

41D180-1 End panels with all labels

(PD610D/PD612D/PD612KLD/7920KD

48930D)

41A5484-1 End panels with all labels

(PD210D/PD212D/248730)

41A5525-5 Cover

41D3452 Limit switch assembly

NOT SHOWN

41A2826 Motor shaft bearing kit

41A2825 Opener assembly hardware kit

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSORIES

953D

7702CB

SECURITY✚^®3-Button Remote

Outside Quick Release:

Control:

Required for a garage with NO

access door.

Includes visor clip.

SECURITY✚^®3-Button Mini

Remote Control:

956D

8 Foot (2.4 m) Rail Extension Kit:

7708CB

7710CB

With key ring and fastening strip.

To allow an 8 foot (2.4 m) door to

open fully.

Motion Detecting Control Panel:

935CB

Multi-function door control with motion

sensor that automatically turns opener

lights on for 5 minutes when it detects a

person entering the garage. Sensor can

be easily deactivated when desired.

10 foot (3 m) Rail Extension Kit:

To allow a 10 foot (3 m) door to

open fully.

945CB

940D

Multi-Function Door Control Panel:

Extension Brackets:

41A5281

Provides a Lock feature which prevents

operation of garage door opener from

portable remotes and a Light feature for

constant light.

(Optional) For safety sensor

installation onto the wall or floor.

To order call: 1-800-528-9131.

SECURITY✚^®Keyless Entry:

Enables homeowner to operate garage

door opener from outside by entering a

password on a specially designed

keyboard. Also can add a temporary

password for visitors or service persons.

This temporary password can be limited

to a programmable number of hours or

entries.

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTIES

CHAMBERLAIN 1 YEAR LIMITED WARRANTY

6 YEAR MOTOR LIMITED WARRANTY

PD210D, PD212D, 7920KD & 248730

The Chamberlain Group, Inc. (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally

installed, that it is free from defect in materials and/or workmanship for a period of 1 YEAR from the date of purchase and that the MOTOR is free

from defect in materials and/or workmanship for a period of 6 YEARS from the date of purchase. The proper operation of this product is dependent

on your compliance with the instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions

will void this limited warranty in its entirety.

If, during the limited warranty period, this product appears to contain

defect covered by this limited warranty, call

1-800-528-9131, toll free, before dismantling this product. Then send this product, pre-paid and insured, to our service center for warranty repair.

You will be advised of shipping instructions when you call. Please include a brief description of the problem and a dated proof-of-purchase receipt

with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be

defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you and returned pre-paid. Defective

parts will be repaired or replaced with new or factory-rebuilt parts at Seller’s sole option.

ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE 1 YEAR LIMITED WARRANTY PERIOD SET FORTH

ABOVE EXCEPT THE IMPLIED WARRANTIES WITH RESPECT TO THE MOTOR, WHICH ARE LIMITED IN DURATION TO THE 6 YEARS

LIMITED WARRANTY PERIOD FOR THE MOTOR, AND NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD. Some

States do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. THIS LIMITED

WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE

(INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE,

UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT), LABOR CHARGES FOR REINSTALLING A REPAIRED OR

REPLACED UNIT, REPLACEMENT OF BATTERIES AND LIGHT BULBS OR UNITS INSTALLED FOR NON-RESIDENTIAL USE.

THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR

HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. THIS LIMITED

WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. ANY SERVICE CALL THAT DETERMINES THE

PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS COULD RESULT IN A FEE TO YOU.

UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN

CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF

WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY.

NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not

apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

CHAMBERLAIN 1 YEAR LIMITED WARRANTY

LIFETIME MOTOR LIMITED WARRANTY

PD610D, PD612D, PD612KLD & 48930D

The Chamberlain Group, Inc. (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally

installed, that it is free from defect in materials and/or workmanship for a period of 1 YEAR from the date of purchase and that the MOTOR is free

from defect in materials and/or workmanship for the lifetime of the product. The proper operation of this product is dependent on your compliance

with the instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions will void this limited

warranty in its entirety.

If, during the limited warranty period, this product appears to contain

defect covered by this limited warranty, call

1-800-528-9131, toll free, before dismantling this product. Then send this product, pre-paid and insured, to our service center for warranty repair.

You will be advised of shipping instructions when you call. Please include a brief description of the problem and a dated proof-of-purchase receipt

with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be

defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you and returned pre-paid. Defective

parts will be repaired or replaced with new or factory-rebuilt parts at Seller’s sole option.

ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE 1 YEAR LIMITED WARRANTY PERIOD SET FORTH

ABOVE EXCEPT THE IMPLIED WARRANTIES WITH RESPECT TO THE MOTOR, WHICH ARE LIMITED IN DURATION TO THE LIFETIME