USER’S GUIDE 2327
General Guide
• Press C to change from mode to mode.
• In any mode (except when making any settings), press L to illuminate the digital
display for about two seconds.
Alarm Mode
Stopwatch Mode
Dual Time Mode
Timekeeping Mode
Calendar Mode
Alarm Mode
Calendar Mode
To set the date
Hold down B.
Press B.
Year
Hold down B.
Hour
Month
Press B.
Day
Press B.
Press B.
Minutes
Month
Day
Day of week
Press B.
Hour
Mode indicator
Minutes
1. In the Calendar Mode, hold down B for about two seconds, until “ADJ” and then
the year digits flash on the display. Keep B depressed until the year digits flash.
2. While any setting is selected (flashing), press C to increase it. Holding down C
changes the flashing setting at high speed.
When an alarm is turned on, an alarm tone sounds for 20 seconds at the preset time
each day.
3. Press B to move the selection around the display in the above sequence.
• The day of the week is automatically set in accordance with the date.
• The date can be set with the range of January 1,1995 to December 31, 2039.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Calendar Mode automatically.
To set the alarm time
1. In the Alarm Mode, hold down B for about two seconds, until “ADJ” and then the
hour digits flash on the display. Keep B depressed until the hour digits flash.
2. Press C to increase the setting. Holding down C changes the current setting at
high speed.
3. Press B to change the selection in the above sequence.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
• The alarm is turned on automatically whenever you change the alarm time setting.
Timekeeping Mode
The minutes hand advances 1/3 of a minute each time the seconds count in the digital
display reaches 00, 20 and 40 seconds.
To set the digital time
Hold down B.
Press B.
To stop the alarm
Seconds
12/24
Hour
Press any button to stop the alarm after it starts to sound.
Press B.
To switch the daily alarm on and off
In the Alarm Mode, press B to turn the daily alarm on and off.
Minutes
ON
OFF
Press B.
Press B.
Hour
Press B.
Seconds
PM indicator
Minutes
1. In the Timekeeping Mode, hold down B for about two seconds, until “ADJ” and
then the seconds digits flash on the display. Keep B depressed until the seconds
digits flash.
2. While the seconds digits are selected (flashing), press C to reset the seconds to
00. If you press C while the seconds count is in the range of 30 to 59, the seconds
are reset to 00 and 1 is added to the minutes. If the seconds count is in the range
of 00 to 29, the minutes count is unchanged.
To test the alarm
Hold down C while in the any mode to sound the alarm.
Stopwatch Mode
3. Press B to move the selection around the display in the above sequence.
4. While hour or minutes are selected (flashing), press C to increase the setting.
Holding down C changes the current setting at high speed. While the 12/24-hour
setting is selected, press C to switch between the two formats.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
The Stopwatch Mode lets you measure elapsed time.
The range of the stopwatch is 23 hours, 59 minutes 59
seconds. The measuring unit for the first hour of elapsed
time measurement is 1/100-second. After that the unit is
one second. You can use the EL backlight at any time
while the stopwatch is operating by pressing L.
1. Press B to start the stopwatch.
Hand setting
2. Press B again to stop the stopwatch.
Each press of A advances the hands 20 seconds. Holding down A advances the
hands at high speed.
• Note that the hands can be advanced only and cannot be moved back. Take care so
you do not go past the setting you want to make.
• You can repeat steps 1 and 2 as many times as you
want.
3. To reset the stopwatch time to all zeros, hold down B.
After the first hour
Minutes
Seconds
Mode indicator
1/100 seconds
About the Backlight
In any mode (except when making any settings), press L to illuminate the digital
display for about two seconds.
Hour
Seconds
Minutes
• The backlight of the watch employs an electro-luminescent (EL) light, which loses
illuminating power after very long use.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch will emit an audible sound whenever the display is illuminated. It does not
indicate malfunction of the watch.
• The backlight automatically stops illuminating whenever an alarm sounds.
• Frequent use of the backlight shortens battery life.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
|