ES
USER’S GUIDE
GUÍA DEL USUARIO
Please keep all information for future reference.
Guarde toda información para tener como referencia futura.
Safety Precautions
Before trying to use the piano, be sure to read
the separate “Safety Precautions”.
Precauciones de seguridad
Antes de intentar usar el piano, asegúrese de
leer las “Precauciones de seguridad” separadas.
AP620/6ES1A
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Download from Www.Somanuals.com. All Manuals Search And Download.
Any reproduction of the contents of this manual, either in part or its entirety, is prohibited. Except for your
own, personal use, any other use of the contents of this manual without the consent of CASIO is prohibited
under copyright laws.
IN NO EVENT SHALL CASIO BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT
LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION)
ARISING OUT OF THE USE OF OR INABILITY TO USE THIS MANUAL OR PRODUCT, EVEN IF CASIO
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
The contents of this manual are subject to change without notice.
The actual appearance of the product may be different from that shown in the illustrations in this User’s
Guide.
Company and product names used in this manual may be registered trademarks of others.
This mark applies in EU countries only.
Manufacturer:
CASIO COMPUTER CO.,LTD.
6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan
Responsible within the European Union:
CASIO EUROPE GmbH
Casio-Platz 1, 22848 Norderstedt, Germany
This mark applies to the AP-620BKV and AP-6BPV.
Please keep all information for future reference.
B
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Assembling the Stand.................................................................................E-56
Unpacking ..........................................................................E-56
To assemble the stand.......................................................E-56
To connect cables..............................................................E-59
To install the music stand and headphones hook..............E-60
General Guide...............................E-2
Recording Your
Saving Settings and Using Panel Lock.................................. E-4
Returning the Digital Piano to Its Factory Default Settings.... E-4
Keyboard Play............................ E-34
Recording or Playing Back a Single Song ........................... E-34
Recording or Playing Back Multiple Songs .......................... E-35
Recording to a Specific Track (Part) .................................... E-35
Deleting Recorder Data........................................................ E-37
Power Supply................................E-5
Connections..................................E-6
Re-recording Part of a Recorder Song
(Punch-in Recording) ........................................................... E-37
Connecting Headphones ....................................................... E-6
Connecting Audio Equipment or an Amplifier ........................ E-6
Bundled and Optional Accessories........................................ E-7
Other Settings ............................ E-40
Configuring Settings............................................................. E-40
Using Built-in Tones.....................E-8
Using a Memory Card................ E-43
Turning on the Digital Piano and Playing Something............. E-8
Selecting a Tone.................................................................... E-8
Layering Two Tones .............................................................. E-9
Splitting the Keyboard between Two Tones ........................ E-10
Using Octave Shift ............................................................... E-11
Adjusting the Brilliance of a Tone ........................................ E-11
Adding Reverb to the Tone.................................................. E-12
Adding the Chorus Effect to the Tone.................................. E-12
Using the Digital Piano’s Pedals.......................................... E-13
Using the Metronome........................................................... E-13
Playing a Duet...................................................................... E-14
Loading and Removing a Memory Card .............................. E-44
Formatting a Memory Card .................................................. E-45
Saving Digital Piano Data to a Memory Card....................... E-45
Loading Data from a Memory Card...................................... E-46
Deleting Memory Card Data................................................. E-47
Renaming a Memory Card File ............................................ E-47
Playing Back a Song from a Memory Card.......................... E-48
Saving Data to Digital Piano Memory (Internal Area)
Instead of a Memory Card.................................................... E-49
Error Messages.................................................................... E-50
Connecting to a Computer........ E-51
Using Auto Accompaniment .....E-16
Minimum Computer System Requirements ......................... E-51
Connecting the Digital Piano to Your Computer .................. E-51
Using MIDI ........................................................................... E-52
Playing an Auto Accompaniment......................................... E-16
Using One-Touch Presets.................................................... E-19
Using Auto Harmonize......................................................... E-19
Creating Your Own Original Rhythms.................................. E-20
Transferring Data between the Digital Piano
and a Computer ................................................................... E-52
Playing Back Built-in Songs......E-23
Reference.................................... E-61
Playing Back All of the Built-in Songs.................................. E-23
Playing Back a Specific Music Library Song........................ E-24
Troubleshooting ................................................................... E-61
Product Specifications.......................................................... E-62
Operating Precautions ......................................................... E-63
Music Presets .............................E-26
Selecting a Music Preset ..................................................... E-26
Creating an Original User Preset......................................... E-27
Appendix....................................... A-1
Tone List ................................................................................ A-1
Drum Assignment List............................................................ A-3
Rhythm List ............................................................................ A-4
Song List ................................................................................ A-6
Music Preset List.................................................................... A-7
Fingering Guide...................................................................... A-9
Chord Example List.............................................................. A-10
Registering Tone and
Rhythm Setups ...........................E-32
Saving Registration Data ..................................................... E-33
Recalling a Registration....................................................... E-33
MIDI Implementation Chart
E-1
Download from Www.Somanuals.com. All Manuals Search And Download.
General Guide
8
9
bl
2
3
4
5
6
7
bk
bm bn bo bp
1
bq
do
br
bs
bt
cs ct dk dl
ck cl cm cn co cp cq cr
dm
dn
Bottom
dr
dp
dq*
ds dt ek el
* With the AP-620BK and AP-6BP, the power cord is hard-wired to the Digital Piano.
B
E-2
Download from Www.Somanuals.com. All Manuals Search And Download.
General Guide
• This manual uses the numbers and names below to refer to buttons and controllers.
POWER button
ELEC PIANO button
INTRO/REPEAT button
VIBES/CLAVI button
NORMAL/FILL-IN, sREW button
VARIATION/FILL-IN, dFF button
SYNCHRO/ENDING, PAUSE button
START/STOP, PLAY/STOP button
ACCOMP ON/OFF, PART button
METRONOME button
ORGAN button
STRINGS/SYNTH-PAD button
BASS/GUITAR button
VARIOUS/GM TONES button
REVERB, REV TYPE, EXIT button
CHORUS, CHOR TYPE, u button
SPLIT, SPLIT POINT, i button
RECORDER button
TEMPO buttons
CARD/INTERNAL, SAVE/LOAD,
ENTER button
RHYTHM, MUSIC LIBRARY button
POPS/JAZZ, MUSIC PRESET button
LATIN/WORLD, MUSIC PRESET button
STORE, USB DEVICE MODE button
SD CARD SLOT
VOLUME controller
PHONES jacks
BALLAD/PIANO RHYTHMS,
RHYTHM EDITOR button
USER RHYTHMS, RHYTHM EDITOR button
Display
AC power jack
USB port
TONE, REGISTRATION button
FUNCTION button
MIDI OUT/IN terminals
LINE IN R, L/MONO jacks
LINE OUT R, L/MONO jacks
Pedal connector
w/NO, q/YES buttons
GRAND PIANO (MODERN) button
GRAND PIANO (CLASSIC) button
E-3
Download from Www.Somanuals.com. All Manuals Search And Download.
General Guide
Saving Settings and Using
Panel Lock
Your Digital Piano lets you save its current settings,
and lock its buttons to protect against operation errors.
For details, see “Setting Backup” (page E-42) and
“Panel Lock” (page E-42).
Returning the Digital Piano to
Its Factory Default Settings
Perform the following procedure when you want to
return the Digital Piano’s stored data and settings to
their initial factory defaults.
1.
2.
Turn off the Digital Piano.
While holding down both the
(TONE) and
(FUNCTION) buttons, press the
(POWER) button.
The Digital Piano will turn on and initialize its internal
system. You will be able to use the Digital Piano in a
short while.
NOTE
• See “Turning on the Digital Piano and Playing
Something” (page E-8) for information about
turning digital power on and off.
E-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Supply
Your Digital Piano runs on standard household power.
IMPORTANT!
• Be sure to turn off power whenever you are not using
the Digital Piano.
Placing the cover on the Digital Piano while power is
on can cause internal circuitry to over heat and lead
to the risk of fire.
1.
Make sure that the POWER button is in the
OFF position (raised).
POWER button
ON
(Power lamp on)
OFF
(Power lamp off)
Front
Power lamp
2.
3.
Connect the power cord that comes with the
Digital Piano to the AC power jack on the
bottom of the Digital Piano.*
* applies to the AP-620BKV and AP-6BPV
Plug the power cord into a household power
outlet.
IMPORTANT!
• Always make sure that the POWER button is the
OFF position before plugging in or unplugging the
power cord.
• The shape of the power cord plug and household
power outlet receptacle differ according to country
and geographical area. The illustration shows just
one example of the shapes that are available.
Make sure the power lamp is completely turned off
before unplugging the power cord from the power
outlet. Be sure to read and observe all of the safety
precautions concerning power supply.
B
E-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting Headphones
Connecting Audio Equipment
or an Amplifier
IMPORTANT!
You can connect audio equipment or a music amplifier
to the Digital Piano and then play through external
speakers for more powerful volume and better sound
quality.
• Before connecting headphones, be sure to use the
Digital Piano’s VOLUME controller to turn the
volume down to a low level. After connecting, you
can adjust the volume to the level you want.
• The Digital Piano automatically adjusts sound output
to optimize for headphones (when headphones are
connected) or the built-in speakers (when
IMPORTANT!
• The Digital Piano automatically adjusts sound output
to optimize for headphone output (when headphones
are connected) or built-in speaker output (when
headphones are not connected). This also will cause
a change in the output quality from the Digital
Piano’s LINE OUT R and L/MONO jacks.
headphones are not connected).
Bottom
PHONES jacks
• Whenever connecting a device to the Digital Piano,
first use the VOLUME controller to set the volume to
a low level. After connecting, you can adjust the
volume to the level you want.
• Whenever you connect any device to the Digital
Piano, be sure to read the user documentation that
comes with the device.
Pin plug
Stereo standard plug
RIGHT (Red)
LEFT (White)
Connect commercially available headphones to the
PHONES jacks. Connecting headphones to either of
the PHONES jack cuts off output to the speakers,
which means you can practice even late at night
without bothering others. To protect your hearing,
make sure that you do not set the volume level too high
when using headphones.
Standard jack
Audio amplifier AUX IN jack, etc.
Portable audio player, etc.
Guitar amplifier
Keyboard amplifier, etc.
Standard plug
INPUT 1
INPUT 2
NOTE
• Be sure to push the headphones plug into the
PHONES jacks as far as it will go. If you don’t, you
may hear sound from only one side of the
headphones.
• If the plug of the headphones you are using does not
match the PHONES jacks, use the applicable
commercially available adaptor plug.
• If you are using headphones that require an adaptor
plug, make sure you do not leave the adaptor
plugged in when you unplug the headphones. If you
do, nothing will sound from the speakers when you
play.
Playing Output from External Equipment
through the Piano’s Speakers
Use commercially available cables to connect the
external audio equipment to the piano’s LINE IN jacks
as shown in Figure .
LINE IN R jack input sounds through the piano’s right
speaker, while LINE IN L/MONO jack input sounds
through the left speaker. Connecting to the LINE IN
L/MONO jack only causes the same output to be
produced from both speakers. It is up to you to
purchase connecting cables that are compatible with
the equipment you are connecting.
B
E-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to Audio Equipment
Bundled and Optional
Accessories
Use only accessories that are specified for use with this
Digital Piano.
Use commercially available cables to connect the
external audio equipment to the piano’s LINE OUT
jacks as shown in Figure . LINE OUT R jack output is
right channel sound, while LINE OUT L/MONO jack
output is left channel sound. It is up to you to purchase
connecting cables like the ones shown in the
Use of unauthorized accessories creates the risk of fire,
electric shock, and personal injury.
illustration for connection of audio equipment.
Normally in this configuration you must set the audio
equipment’s input selector to the setting that specifies
the terminal (such as AUX IN) to which the piano is
connected. Use the piano’s VOLUME controller to
adjust the volume level.
NOTE
• You can get information about accessories that are
sold separately for this product from the CASIO
catalog available from your retailer, and from the
CASIO website at the following URL.
Connecting to a Musical Instrument
Amplifier
Use commercially available cables to connect the
amplifier to the piano’s LINE OUT jacks as shown in
Figure . LINE OUT R jack output is right channel
sound, while LINE OUT L/MONO jack output is left
channel sound. Connecting to the LINE OUT
L/ MONO jack only outputs a mixture of both
channels. It is up to you to purchase connecting cable
like the one shown in the illustration for connection of
the amplifier. Use the piano’s VOLUME controller to
adjust the volume level.
E-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Built-in Tones
8METRONOME
btw, q
ctCHORUS, u
blMUSIC LIBRARY
bsFUNCTION
brTONE
csREVERB dkSPLIT, i
dlENTER
7PART
–
Tone groups
bkTEMPO
Turning on the Digital Piano
and Playing Something
Selecting a Tone
Your Digital Piano has 250 tones, divided into eight
groups.
• For more information, see the “Tone List” (page
A-1).
• The Digital Piano has built-in demonstration tunes
that highlight the different characteristics of tones.
For more information, see “Playing Back All of the
Built-in Songs” (page E-23).
1.
Press the
(POWER) button.
This turns on power.
• To turn off the Digital Piano, press the
again.
button
Left Side
button
1.
Press the
is lit.
(TONE) button so its upper lamp
• Each press of the button toggles between the upper
and lower lamps.
Lit
2.
After a short while, the display screen should
appear as shown below, which indicates that
the Digital Piano is ready to be played.
IMPORTANT!
• Continuing on to the next step while the
REGISTRATION lamp is lit will perform a registration
recall operation (page E-32), which will change the
setup of the Digital Piano. Make sure that the TONE
lamp is lit before you advance to the next step.
2.
Use the “Tone List” (page A-1) to look up the
group and the number of the tone you want to
select.
3.
4.
Use the
volume level.
(VOLUME) controller to adjust the
Play something on the keyboard.
B
E-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Built-in Tones
3.
4.
Use the
select the group you want.
to
(tone groups) buttons to
2.
Hold down the button of the group that
contains the tone you want to select as the
layered tone until “LAYER: ON” appears on
the display as shown below for a few
moments.
Example: To select the ORGAN group
This will layer the tones currently selected in the two
groups.
Lit
Use the
tone you want.
(w, q) buttons to select the
Example: To select “002 Jazz Organ”
Tone number
Tone name
The button you held down in step 2 will light to
indicate that it is selected.
Example: When BASS/GUITAR group is selected
Lit
NOTE
• Pressing q and w at the same time will jump to
tone 001 of the currently selected group. Holding
down either button changes the tone number at high
speed.
3.
4.
Use the
(w, q) buttons to select the
tone you want in the group you selected in
step 2.
• See page E-40 for more information about scrolling.
Example: When “006 Picked Bass” is selected
Layered tone number
Layered tone name
Layering Two Tones
You can layer two different tones so they play at the
same time when you press a keyboard key.
• The first tone you select is called the “main tone,”
while the second tone is called the “layered tone.”
1.
Select the main tone.
Example: To select MELLOW PIANO in the CLASSIC
To unlayer the tones and return the keyboard
to a single tone, press any one of the tone
group buttons.
group, press the
(CLASSIC) button and
then use the
(w, q) buttons to select
“002 Mellow Piano”.
NOTE
• You can adjust the balance between the main tone
and layered tone. For details, see “Layer Balance”
(page E-41).
B
E-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Built-in Tones
Moving the Keyboard Split Point
Splitting the Keyboard
between Two Tones
You can split the keyboard so the left side (lower
range) plays one tone and the right side (upper range)
plays a different tone.
You can use the procedure below to specify the
location on the keyboard where it splits between the
left side and the right side. That location is called the
“split point”.
Left (Lower Range) side
Right (Upper Range) side
Example: To split the keyboard between the GM SLAP
BASS 1 tone on the left (lower range) and the
GRAND PIANO tone on the right (upper range).
Left (Lower Range)
Tone: GM SLAP BASS 1
Right (Upper Range)
Tone: GRAND PIANO
Split point
1.
Hold down the
split point setting screen appears on the
display as shown below.
(SPLIT) button until the
1.
2.
Press the
(SPLIT) button.
This causes the SPLIT lamp to light, indicating that the
keyboard is split between two tones.
Lit
Current split point key name
Select the tone you want to assign to the left
side (lower range) of the keyboard.
2.
3.
Press the keyboard key where you want to
specify as the leftmost key of the right (upper
range) tone.
Example: To select GM SLAP BASS 1 in the VARIOUS/
GM TONES group, press the
GM TONES) button and then use the (w,
q) buttons to select “073 GM SlapBass1”.
(VARIOUS/
This specifies the split point.
Press the
(SPLIT) button.
This exits the split point screen.
Lit
Left tone number
Left tone name
3.
To unsplit the keyboard and return it to a
single tone, press the
(SPLIT) button.
The SPLIT lamp will go out, indicating that the
keyboard is no longer split.
NOTE
• If the keyboard is set up with layered tones (page
E-9) when you perform the above split operation,
the layered tones will play on the right (upper
range) side of the keyboard.
E-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Built-in Tones
Using Octave Shift
Adjusting the Brilliance of a
Tone
After you split the keyboard (page E-10), you may find
out that the lower range notes on the left are too low or
that the upper range notes on the right are too high.
You can use octave shift to shift the octaves of the
upper range and lower range upwards or downwards
in octave units.
1.
Press the
(FUNCTION) button.
The FUNCTION lamp will light and the function screen
will appear on the display.
1.
While holding down the
(FUNCTION)
button, press the
(TONE) button.
This displays the octave shift screen.
Lit
2.
Use the
the Tmpr/Effect screen.
(i) and
(u) buttons to select
Currently selected range
Shift amount
2.
Use the
(PART) button to select the range
3.
4.
Press the
(ENTER) button.
whose octave you want to change.
• Each press of
below.
This will display a screen for selecting settings in the
Tmpr/Effect group.
(PART) cycles through the ranges
Use the
(i) or
(u) button to select
U1 (Upper1): Main tone
the brilliance screen shown below.
U2 (Upper2): Layered tone
L1 (Lower1): Left (lower range) tone
3.
4.
Use the
(w, q) buttons to shift the
5.
6.
Use the
(
w
,
q) buttons to adjust the
octave of the currently selected range.
• You can shift the octave within the range of –2 to 0 to
2.
brilliance of the currently selected tone. You
can adjust brilliance in the range of –3 to 0 to 3.
w: Mellower and softer
q: Brighter and harder
Press the
This exits the octave shift screen.
(FUNCTION) button.
Press the
(FUNCTION) button.
NOTE
This will exit the brilliance screen and cause the
FUNCTION lamp to go out.
• Octave shift also can be performed as described for
“Octave Shift” (page E-41).
NOTE
• See “Other Settings” (page E-40) for details about
using the (FUNCTION) button.
E-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Built-in Tones
Adding Reverb to the Tone
Adding the Chorus Effect to
the Tone
1.
Press the
reverb on and off.
(REVERB) button to toggle
1.
Press the
(CHORUS) button to toggle
Lit when on
chorus (which adds depth to a tone) on and
off.
Lit when on
Selecting the Reverb Type
You can select from among the following four types of
reverb.
Selecting the Chorus Type
You can select from among the following four chorus
types.
1: Room
2: Hall
3: Large Hall
4: Stadium
1: LightChorus
2: Chorus
3: Deep Chorus
4: Flanger
1.
Hold down the
reverb type selection screen shown below
(REVERB) button until the
1.
Hold down the
chorus type selection screen shown below
(CHORUS) button until the
appears on the display.
appears on the display.
2.
3.
Use the
reverb type you want.
(w, q) buttons to select the
2.
3.
Use the
chorus type you want.
(w, q) buttons to select the
Press the (REVERB) button to exit the
reverb type screen.
Press the (CHORUS) button to exit the
chorus type screen.
E-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Built-in Tones
Using the Digital Piano’s
Pedals
Your Digital Piano comes equipped with three pedals:
damper, soft, and sostenuto.
Using the Metronome
1.
Press the
This will start the metronome.
(METRONOME) button.
Soft pedal
Damper pedal
Sostenuto pedal
Lights with the first beat
of each measure
Lights with each subsequent beat of
each measure
Pedal Functions
2.
Press the
stop the metronome.
(METRONOME) button again to
Damper Pedal
Pressing the damper pedal while playing will cause the
notes you play to reverberate for a very long time.
• When a GRAND PIANO tone (MODERN, CLASSIC,
VARIATION) is selected as the tone, pressing this
pedal will cause notes to reverberate (acoustic
resonance) just like the damper pedal on an acoustic
grand piano. Half-pedal operation (pressing the
pedal part way) is also supported.
Changing the Beats Per Measure
You can specify from two to six beats per measure for
the metronome. After you do, a chime will sound at the
beginning of each measure. Specifying 0 for this setting
will sound a straight beat, without a chime. This setting
lets you practice with a steady beat.
Soft Pedal
Pressing this pedal while playing suppresses notes
played on the keyboard after the pedal was pressed,
and makes them sound softer.
1.
Hold down the
until the number of beats per measure screen
shown below appears on the display.
(METRONOME) button
Sostenuto Pedal
Only the notes of the keys that are depressed when this
pedal is pressed are sustained until the pedal is
released.
2.
3.
Use the
(w, q) buttons to select the
beats per measure value you want.
Press the (METRONOME) button to exit
the number of beats per measure screen.
E-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Built-in Tones
Changing the Tempo Setting
Adjusting the Metronome Volume
There are two different methods you can use to change
the tempo setting: by pressing q (faster) and w
(slower) buttons or by tapping a beat with a button.
You can use the following procedure to adjust the
volume level of the metronome, without affecting the
volume of Digital Piano output.
1.
While holding down the
(FUNCTION)
■ To adjust the tempo using q and w
buttons
button, press the
(METRONOME) button.
This displays the metronome volume screen.
1.
Use the
adjust the tempo setting.
(TEMPO w, q) buttons to
Each press of a button increases or decreases the beats
per minute value by one.
• Holding down either button changes the value at
high speed.
• You can specify a tempo value in the range of 20 to
255.
Metronome volume
2.
3.
Use the
metronome volume.
(w, q) buttons to adjust the
Press the (FUNCTION) button.
This will exit the metronome volume screen and cause
the FUNCTION lamp to go out.
Tempo value
NOTE
■ To adjust the tempo by tapping a beat
• You also can use the procedure under “Metronome
Volume” (page E-41) to adjust the metronome
volume.
1.
While holding down the
(FUNCTION)
button, tap the q
(TEMPO) button four
times in time with the beat you want to
specify.
Playing a Duet
• The tempo setting will change in accordance with the
timing of your tapping.
• After you use this method to specify the approximate
tempo, you can then use the procedure under “To
adjust the tempo using q and w buttons” to adjust
the setting to a more exact value.
You can use the Duet Mode to split the Digital Piano’s
keyboard in the center so two people can play a duet.
This makes it possible to configure the keyboard so, for
example, the teacher can play on the left and the
student can follow along on the right. Or one person
can play the left hand part on the left, while another
plays the right hand part on the right.
Tap four times
Left keyboard
Right keyboard
C3
C4
C5
C6
C3
C4
C5
C6
(Middle C)
(Middle C)
Pedal Operation when Playing a Duet
Right side damper pedal
(Half-pedal operation
supported)
Left keyboard
damper pedal
Left and right side damper pedal
E-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Built-in Tones
Configuring the Digital Piano for Duet
Play
Changing the Octave of a Duet Mode
Keyboard
You can use the following procedure to change the
octave of the left and right Duet Mode keyboards.
1.
Press the
lower lamp is lit.
(MUSIC LIBRARY) button so its
1.
While holding down the
(FUNCTION)
button, press the
(SPLIT) button.
This displays the Duet Mode on/off screen shown in
step 2 under “Configuring the Digital Piano for Duet
Play” (page E-15). If the Duet Mode is currently turned
Lit
off, press the
(q) button to turn it on.
• To practice with songs stored on a memory card,
2.
Of the four C keys in the left keyboard, press
the one that you want to have located at
middle C.
press the
(CARD/INTERNAL) button so its lamp
is lit in place of the
(MUSIC LIBRARY) button.
2.
While holding down the
(FUNCTION)
• This will sound the note assigned to C4 and change
the octave of the left keyboard.
Example: To change the configuration so the leftmost C
button, press the
(SPLIT) button.
This causes the Duet Mode on/off screen to appear.
key is middle C as shown below.
Leftmost C key (Pressed key)
C4
C5
C6
C7
C3
C4
C5
C6
1 octave higher than initial setting
Unchanged
3.
4.
Press the
Mode.
(q) button to turn on the Duet
(FUNCTION) button.
3.
4.
You can use the same procedure as step 2 to
select one of the C keys in the right keyboard
to shift its octave as well.
Press the
This exits the Duet Mode on/off screen and configures
the Digital Piano’s keyboard for duet play.
This will cause the
Press the
(FUNCTION) button.
(SPLIT) button lamp to flash.
This exits the Duet Mode on/off screen and causes the
(FUNCION) button lamp to go out.
5.
To turn off the Duet Mode, press the
(SPLIT) button so the SPLIT lamp goes out.
The left and right keyboards will be configured
according to your settings.
NOTE
NOTE
• You also can use the procedure under “Duet Mode”
(page E-41) to turn the Duet Mode on or off.
• Turning off the Duet Mode will clear your octave
shift settings and return the keyboard to its initial
default settings.
B
E-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Auto Accompaniment
5SYNCHRO/ENDING
6START/STOP
blRHYTHM
boBALLAD/PIANO RHYTHMS
btw/NO, q/YES
brTONE csEXIT dlENTER
bpUSER RHYTHMS
–
Accompaniment
bkTEMPO
patterns
–
–
Rhythm groups
Instrument parts
7ACCOMP ON/OFF
With Auto Accompaniment, simply select the
accompaniment rhythm you want and the matching
accompaniment (drums, guitar, etc.) will play
automatically when you play a chord with your left
hand. It’s like having your own personal backup group
along with you wherever you go.
3.
4.
Use the
select the group you want.
to
(rhythm groups) buttons to
Example: When the LATIN/WORLD group is selected
This Digital Piano has 180 built-in Auto
Accompaniment patterns, which are divided into three
groups. You can edit built-in rhythms to create your
own original rhythms (called “user rhythms”), which
you can save in a fourth group. For more information,
see the “Rhythm List” (page A-4).
Lit
Use the
rhythm you want.
(w, q) buttons to select the
Example: When “005 Samba 2” is selected
Playing an Auto
Accompaniment
1.
Press the
lamp is lit.
(RHYTHM) button so its upper
This enables Auto Accompaniment.
• Each press of the button toggles between the
RHYTHM and MUSIC LIBRARY lamps.
Rhythm name
Tempo
Rhythm number
Measure
Lit
5.
Use the
adjust the tempo setting.
(TEMPO w, q) buttons to
• This is the same as metronome tempo adjustment
(page E-14).
• To return the rhythm to its standard tempo setting,
press the
time.
(TEMPO w, q) buttons at the same
2.
Use the “Rhythm List” (page A-4) to look up
the group and the number of the rhythm you
want to select.
E-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Auto Accompaniment
6.
7.
Press the
its lamp is lit.
This turns ACCOMP on, so all accompaniment parts
sound.
• Turning ACCOMP off so the ACCOMP lamp is unlit
causes only the percussion instrument parts to sound.
(ACCOMP ON/OFF) button so
9.
Play other chords with left hand as you play
the melody with your right hand.
• You can use “CASIO Chord” or other simplified
chord fingering modes to play chords. For details, see
“Selecting a Chord Fingering Mode” in the following
section.
• You can use the
(NORMAL) and
• Each press of the
toggles ACCOMP on and off.
(ACCOMP ON/OFF) button
(VARIATION) buttons to modify accompaniment
patterns. For details, see “Modifying Auto
Accompaniment Patterns” (page E-19).
Lit
10. When you are finished, press the
STOP) button again to stop Auto
Accompaniment.
(START/
• Pressing the
(SYNCHRO/ENDING) button
Press the
(SYNCHRO/ENDING) button.
instead of the
(START/STOP) button will play an
ending pattern before stopping Auto
Accompaniment play. For details about ending
patterns, see “Modifying Auto Accompaniment
Patterns” (page E-19).
This puts Auto Accompaniment into “synchro
standby”. Playing a chord during synchro standby will
cause Auto Accompaniment to start to play
automatically.
• Pressing the
Accompaniment is in synchro standby will enter
intro standby. Pressing the (VARIATION) button
(INTRO) button while Auto
NOTE
• You can use the following procedure to adjust the
volume level of the Auto Accompaniment, without
affecting the volume of Digital Piano output. For
details, see “Auto Accompaniment Volume” (page
E-41).
will enter variation standby. For details about intro
and variation patterns, see “Modifying Auto
Accompaniment Patterns” (page E-19).
Flashing
• You can change the size of the chord keyboard by
using the split feature to move the split point (page
E-10). The keyboard keys to the left of the split point
make up the chord keyboard.
8.
Play the chord you want on the chord
keyboard (left keyboard keys).
Auto Accompaniment will start playing when you play
the chord.
• To start percussion part play without playing a
chord, press the
(START/STOP) button.
Example: To play a C chord
Chord keyboard
Melody keyboard
E-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Auto Accompaniment
■ CASIO CHORD
Selecting a Chord Fingering Mode
With “CASIO Chord”, you can use simplified
fingerings to play the four types of chords described
below.
You can select from among the following five chord
fingering modes.
1: Fingered 1
2: Fingered 2
3: Fingered 3
4: CASIO Chord
5: Full Range
Chord keyboard
Chord Type
Example
1.
Hold down the (ACCOMP ON/OFF) button
until the chord type selection screen appears
on the display.
Major Chords
C (C Major)
CC#DEb E
F
F#GAbABb
B
CC#DEb E
F
Press one key, whose note
corresponds to the chord
name.
Note name
• To play C Major, press any
C key in the chord
keyboard. The octave of the
note does not matter.
Minor Chords
Cm (C minor)
CC#DEb E
F
F#GAbABb
B
CC#DEb E
F
Press the chord keyboard key
that corresponds to the major
chord, while also pressing one
other chord keyboard key to
the right.
Chord fingering mode
2.
3.
Use the
(w, q) buttons to select the
chord fingering mode you want.
Seventh Chords
C7 (C seventh)
CC#DEb E
F#GAbABb
F
B
CC#DEb E
F
Press the chord keyboard key
that corresponds to the major
chord, while also pressing
two other chord keyboard
keys to the right.
Press the (ACCOMP ON/OFF) button.
This exits the chord fingering screen.
■ Fingered 1, 2, 3
Minor Seventh Chords
Press the chord keyboard key
that corresponds to the major
chord, while also pressing
three other chord keyboard
keys to the right.
Cm7 (C minor seventh)
CC#DEb E CC#DEb E
F#GAbABb
With these three chord fingering modes, you play
chords on the chord keyboard using their normal
chord fingerings. Some chord forms are abbreviated,
and can be fingered with one or two keys.
For information about the types of chords you can
finger and their fingerings, see the “Fingering Guide”
(page A-9).
F
B
F
When pressing more than one chord keyboard key,
makes no difference whether the additional keys are
white or black.
Chord keyboard
■ FULL RANGE CHORD
With this chord fingering mode, you can use the full
range of the keyboard to play chords and the melody.
For information about the types of chords you can
finger and their fingerings, see the “Fingering Guide”
(page A-9).
Fingered 1: Play the component notes of the chord on the
keyboard.
Fingered 2: Unlike Fingered 1, 6th input is not possible with
this mode.
Fingered 3: Unlike Fingered 1, this mode allows input of
fraction chords with the lowest keyboard note as
the bass note.
Melody keyboard
Chord keyboard
E-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Auto Accompaniment
Modifying Auto Accompaniment Patterns
Using One-Touch Presets
One-Touch Preset gives you one-touch access to tone
and tempo settings that go well with the currently
selected Auto Accompaniment rhythm pattern.
There are six different Auto Accompaniment patterns,
shown below. You can switch between patterns during
accompaniment play and even modify patterns. Use
buttons
through
to select the pattern you want.
1.
Hold down the
least two seconds.
(RHYTHM) button for at
This will configure tone, tempo, and other settings to
match the currently selected rhythm pattern. At this
time, Auto Accompaniment play also will go into
synchro standby, which means that Auto
Accompaniment will start to play automatically when
you finger a chord.
Intro *1
Normal
Variation
Ending *4
2.
Play a chord on the keyboard.
This will start Auto Accompaniment play.
Normal fill-in *2
Variation fill-in *3
*1 Press at the beginning of a song.
NOTE
Accompaniment play proceeds with the normal
pattern after the intro pattern is complete. Pressing
• One-Touch Presets are not supported for user
rhythms (001 through 010 of the USER RHYTHMS
group).
the
(VARIATION/FILL-IN) button before
pressing this button will proceed with the variation
pattern after the intro pattern is complete.
*2 Press while a normal pattern is playing to insert a
fill-in pattern.
*3 Press while a variation pattern is playing to insert a
fill-in variation pattern.
Using Auto Harmonize
Auto Harmonize lets you add harmony to melody
notes you play with your right hand. You can select
any one of 12 Auto Harmonize settings.
*4 Press at the end of a song.
This will play an ending pattern and then stop Auto
Accompaniment.
1.
Press the
(TONE) button so its lamp is lit.
Lit
2.
Hold down the
auto harmonize screen appears on the
display.
(TONE) button until the
Type number
Type name
E-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Auto Accompaniment
3.
Use the
(w, q) buttons to select the
Creating Your Own Original
Rhythms
You can use rhythm editing to modify a built-in Auto
Accompaniment rhythm to create an original “user
rhythm” of your own. You can select a part (drum,
bass, etc.) of a normal, intro, or other pattern (page
E-19) and turn it on or off, adjust its volume level, and
perform other operations.
Auto Harmonize type you want.
Type
Number
Type Name
Off
Description
00
Turns off Auto Harmonize.
Adds close (separated by two to
four degrees) one-note harmony
below the melody note.
01
Duet 1
Adds open (separated by more
than 4 to 6 degrees) 1-note
harmony below the melody
note.
02
Duet 2
1.
2.
Select the number of the Auto
Accompaniment rhythm you want to edit.
03
04
05
06
Country
Octave
Adds country style harmony.
At the same time, press the
(BALLAD/
Adds the note from the next
lower octave.
PIANO RHYTHMS) and
RHYTHMS) buttons.
(USER
5th
Adds the fifth degree note.
This displays the rhythm editor screen.
Adds 2-note open harmony, for
a total of three notes.
3-Way Open
Adds 2-note close harmony, for
a total of three notes.
07
08
09
10
3-Way Close
Strings
Adds harmony that is optimal
for strings.
Adds 3-note open harmony, for
a total of four notes.
4-Way Open
4-Way Close
3.
Use the accompaniment pattern buttons (
Adds 3-note close harmony, for
a total of four notes.
through ) to select the pattern (normal,
intro, ending, etc.) you want to edit.
The button you press will light, indicating that the
pattern is being edited.
11
12
Block
Adds block chord notes.
Big Band
Adds big band style harmony.
• Each press of
(NORMAL/FILL-IN) toggles
4.
5.
Press the
This will exit the auto harmonize screen.
(TONE) button.
between NORMAL and FILL-IN, and each press of
(VARIATION/FILL-IN) toggles between
VARIATION and FILL-IN. The applicable button
flashes while the fill-in pattern is selected.
Example: When intro is selected
While playing chords, play the melody on the
keyboard.
Harmony will be added to your melody notes based on
the chords you play.
E-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Auto Accompaniment
4.
Use the instrument part buttons ( through
Shortcut
Button
Parameter Description
Replaces the part
Setting
) to select the part (drums, bass etc.) you
want to edit.
(drum, bass, etc.)
accompaniment
data with that of the
specified rhythm
number. *1
The name of the part you select will appear on the
display. Rhythm patterns are made up of the eight parts
shown below.
Rhythm
Select:
Rhythm
001 to 190:
Rhythm number
*2 *3
ck
cl
cm
cn
co
cp
cq
cr
Switches the part
Tone
Select:
Tone
tone (instrument) to 001 to 250: Tone
that of the specified Numbers *2 *4
tone number.
Drums Percus-
sion
Bass
Chord 1 Chord 2 Chord 3 Chord 4 Chord 5
Parts
OFF:
Prt:
Toggles each part on Mutes the part.
Part on/off or off.
ON:
Sounds the part.
• Button illumination does not change when you press
the instrument part buttons ( through ). Button
Vol:
Volume
level
illumination indicates whether there is
accompaniment data corresponding to each part.
Example: When bass is selected
Controls the volume
000 to 127
level of each part.
Controls whether
the sound of the part
can be heard from
the left side or right
side.
Pan:
Panning
(position)
–64 to 0 to 63 *5
Controls the level of
the reverb effect
(page E-12) applied
to the part notes.
Reverb:
Reverb
000 to 127
000 to 127
Instrument part name
Controls the level of
the chorus effect
(page E-12) applied
to the part notes.
5.
Edit the selected part as desired.
The table below describes the parameters you can edit.
Chorus:
Chorus
• Use the
(u) and
(i) buttons to select a
parameter, and the
setting. You also can use shortcut buttons (see table
below) to select parameters.
(w, q) buttons to change its
*1 Replacing part accompaniment data clears all edits to the
currently selected accompaniment data made up to that
point.
*2 Sequential numbers starting from 001, which is the first
rhythm of the first group (POPS/JAZZ). See the “Tone
List” (page A-1) and “Rhythm List” (page A-4) for
information on the numbering system.
*3 In the case of the intro and ending, specifying a rhythm
for one part (drum, bass, etc.) will cause the same rhythm
to be specified automatically for all of the other parts of
the pattern.
• Pressing the
(w, q) buttons at the same time
will return the currently selected parameter to its
initial default setting.
• Pressing the
(START/STOP) button during an
edit operation will sound the accompaniment pattern
with the edits you have made up to that point.
Pressing the
(ACCOMP ON/OFF) button will
sound only the instrument part you are editing.
*4 Only drum set sounds (tone numbers 237 through 250)
can be selected for drum parts and percussion parts.
Drum set sounds cannot be selected for the bass and the
chord 1 through chord 5 parts.
Procedure continues on page E-22.
*5 A smaller value shifts leftward, while a larger value shifts
rightward. A value of zero specifies center.
E-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Auto Accompaniment
6.
Repeat steps 3 through 5 to edit all of the
accompaniment patterns and parts you want.
10. Decide on the user rhythm number where you
want to save the rhythm and a rhythm name.
• Use the
(u) and
(i) buttons to move the
7.
After editing is complete, adjust the tempo of
the rhythm as desired.
• The tempo you set here becomes the initial default
tempo of the rhythm.
cursor to the user rhythm number and rhythm name
character you want to change. Use the (w, q)
buttons to select the number or character you want.
• The rhythm name characters you can select are
shown below. To input a space, press both of the
(w and q) buttons at the same time.
8.
Press the
(EXIT) button.
This causes a confirmation message to appear asking if
you want to save your edits.
9.
Press the
(YES) button.
This displays a screen for specifying the user rhythm
number and rhythm name.
• If you want to exit the editing operation without
saving, press the
(YES) button.
(NO) button instead of the
11. Press the
(ENTER) button.
This saves the data.
• If the rhythm number where you are saving the data
already has data saved to it, a message (Replace?) will
appear on the display to confirm whether you want
to replace the existing data with the new data. Press
the
(YES) button to replace. To cancel the save
operation and return to the screen in step 9, press the
(NO) button instead.
Rhythm name
Destination user rhythm number
IMPORTANT!
• Saving user rhythm data to a user rhythm number
that already has data will cause the existing data to
be replaced by the new data.
NOTE
• If the size of the accompaniment pattern or
instrument part data is too large to be edited, a
memory full message (Memory Full) will appear on
the display. If that happens, select a different
accompaniment pattern or instrument part for
editing.
E-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Back Built-in Songs
blMUSIC LIBRARY
btw, q
dlCARD/INTERNAL
6PLAY/STOP
2REPEAT
7PART
–
–
Song groups A to D
Tone groups
2.
Press the
This stops demo song playback.
Playback of the demo songs will continue in an endless
loop until you press the
stop it.
(PLAY/STOP) button.
Playing Back All of the Built-in
Songs
Your Digital Piano comes with a total of 68 built-in
songs: eight demo songs that are arranged to highlight
the characteristics of the tones in each of the tone
groups, and 60 classics in the Music Library. You can
configure the Digital Piano to play back these songs in
sequence.
(PLAY/STOP) button to
NOTE
• Only the operations described above can be
performed while demo song playback is in progress.
• See “Song List” (page A-6) for a list of built-in songs.
1.
While holding down the
(PART) button,
press the
(PLAY/STOP) button.
This will start sequential playback of the tone demo
songs, starting from song 1.
Song number
Current measure
Song tempo
Song name
• Pressing a tone group button (buttons
through
)
while demo song playback is in progress will switch
to the demo song that uses the tones of that group.
Pressing a Music Library song group button (buttons
through , Group A through C) while demo song
playback is in progress will switch to playback of the
songs in that group.
• Pressing the
(CARD/INTERNAL) button during
demo song playback will start playback of the songs
on the loaded card. For details, see “Playing Back All
of the Songs in a Folder” (page E-48).
B
E-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Back Built-in Songs
5.
Press the
This starts playback of the song.
• Press the (FF) button to perform a fast forward
operation or the
(PLAY/STOP) button.
Playing Back a Specific Music
Library Song
(REW) button for rewind.
You can use the procedure below to select a Music
Library song for listening or practice.
Pressing and releasing either button moves one
measure, while holding down a button scrolls at high
speed.
• Pressing the
Press again to resume song playback.
(PAUSE) button pauses playback.
The Music Library has a total of 60 songs, divided into
three groups (A, B, C). You also can load songs from a
memory card or your computer into a fourth Music
Library group (Group D) for playback and practice
(pages 46 and 52).
Lights with each subsequent beat of each measure
Lights with the first beat of each measure
2
3
4
5
6
1.
Press the
lamp is lit.
(MUSIC LIBRARY) button so its
• Each press of the button toggles between the upper
and lower lamps.
Rewind
Pause
Fast forward
6.
Press the
This stops song playback.
(PLAY/STOP) button again.
Lit
• Song playback also will stop automatically when the
end of the song is reached. To configure the Digital
Piano to loop song playback without stopping, turn
on “Song Repeat” (page E-42).
2.
3.
In the “Song List” (page A-6), find the group
and group number of the song you want.
• User songs are in Group D.
Changing the Song Tempo
Use the
to select the group you want.
• Press button
song.
to
(Song group A to D) buttons
You can change the song tempo using the same
procedure that you use to adjust the metronome
tempo. For more information, see “Changing the
Tempo Setting” (page E-14).
(Group D) if you want to select a user
Example: When Group B is selected
Playing on the Keyboard Using the Same
Tone as the Song
1.
Hold down the
for at least two seconds.
(MUSIC LIBRARY) button
Lit
This will assign the same tone as the right hand part of
the current song to the keyboard.
4.
Use the
song you want.
(w, q) buttons to select the
NOTE
• You can use the procedure under “Practicing Either
Hand’s Part (Part Off)” (page E-25) to turn off the
left hand part and play along on the keyboard using
the left hand part tone.
Example: When “008 Gavotte” is selected
Song number
Song name
E-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Back Built-in Songs
Adjusting the Song Volume
Repeating Playback of a Specific Section
(Repeat)
You can use the following procedure to adjust the
volume level of the song’s Auto Accompaniment,
without affecting the volume of keyboard tone output.
For details, see “Song Volume” (page E-41).
You can configure the Digital Piano to repeat the
section of a song you want to practice. You could, for
example, specify repeat play from measure 5 to
measure 8.
Start
End
Practicing Either Hand’s Part (Part Off)
You can turn off the right hand part or left hand part of
a song and play that part on the Digital Piano while the
song plays back.
These measures are repeated.
1.
2.
Press the
(PART) button.
1.
2.
Press the
This starts playback of the song.
(PLAY/STOP) button.
This causes “L-[ON] R-[ON]” to appear on the display.
Use the
(w, q) buttons to turn off the
When playback reaches the first measure of
the section you want to repeat, press the
(REPEAT) button.
part you want.
Press (w) to toggle the left hand part or (q) to toggle
the right hand part on and off.
This makes the measure the “start measure”.
3.
4.
Press the
This exits the part on/off screen.
(PART) button again.
The
(REPEAT) button lamp flashes at this time.
3.
4.
When playback reaches the last measure of
the section you want to repeat, press the
(REPEAT) button again.
This makes the measure the “end measure”.
Repeat playback of the specified section starts as soon
as you select the end measure.
Hold down the
for at least two seconds.
This will assign the same tone as the hand that is turned
off to the keyboard.
(MUSIC LIBRARY) button
5.
Press the
song playback.
The part you turned off does not sound, so you can play
it on the keyboard.
(PLAY/STOP) button to start
The
(REPEAT) button lamp is lit (not flashing) at
this time.
Pressing
(REPEAT) again returns to
normal play.
Sounding a Count at the Beginning of a
Song
This will cause the
(REPEAT) button lamp to go out.
You can configure the Digital Piano to sound a count
before playback of a song starts, which helps to get the
timing right when you are playing along on the
keyboard. For details, see “Pre-count” (page E-42).
E-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Music Presets
6START/STOP
blRHYTHM
btw/NO, q/YES
ctu
dlENTER
–
Music Preset groups
csEXIT dki
–
Tone groups
4FF
3REW 7ACCOMP ON/OFF bmbnMUSIC PRESET
Music Presets provide you with one-touch tone,
rhythm, chord, and other settings that are optimized
for specific musical genres and songs.
In addition to built-in presets, you can create your own
original Music Presets (user presets).
Selecting a Music Preset
1.
Press
same time.
and
(MUSIC PRESET) at the
This causes the
and the Music Preset screen to appear.
(ACCOMP ON/OFF) lamp to flash
There are a total of 300 built-in Music Presets, which
are divided into three groups (A, B, C). A fourth group
(D) is provided for user presets.
• For more information, see the “Music Preset List”
(page A-7).
Music Preset number
Music Preset name
2.
Use buttons
buttons) to select a group, and then use the
to
(Music Preset group
(w, q) buttons to select the Music
Preset you want.
This will configure the Digital Piano with settings (tone,
rhythm, etc.) of the selected Music Preset.
The following are the settings that are included in a
Music Preset.
• Tones (main, layer, lower split) (page E-8)
• Layer balance (page E-9)
• Octave shift (page E-11)
• Reverb (page E-12)
• Chorus (page E-12)
• Rhythm (page E-20)
• Tempo (page E-19)
• Auto Harmonize (page E-19)
B
E-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Music Presets
3.
Press the
(START/STOP) button to start
Creating an Original User
Auto Accompaniment with the chord
progression of the Music Preset. Play the
melody on the keyboard.
• The preset chord progression repeats until you stop it
by pressing the
Preset
A Music Preset editor is provided to allow you to
create your own original Music Presets (user presets).
Up to 50 user presets can be stored in Music Preset
Group D.
(START/STOP) button again.
• Pressing the
(ACCOMP ON/OFF) button so the
ACCOMP ON/OFF lamp is lit (not flashing) or unlit
will turn off the chord progression of the Music
Preset and play the normal Auto Accompaniment
pattern.
• Each press of the
cycles in the sequence shown below.
1.
2.
Select the Music Preset you want to edit in
order to create your user preset.
(ACCOMP ON/OFF) button
Change the tone number, rhythm number,
and other settings of the Music Preset as you
want.
Unlit
Lit
Flashing
• The settings you configure here will be saved as a
user Music Preset. See step 2 under “Selecting a
Music Preset” (page E-26) for the settings you can
configure and save for a user Music Preset.
Music Preset
chord progression
Normal Auto Accompaniment
3.
Press the
(BALLAD/PIANO RHYTHMS)
• You can use the following steps to change the rhythm
after selecting a Music Preset.
and
(USER RHYTHMS) buttons at the
same time.
This displays a screen for selecting the type of editing
operation you want to perform.
(1) Hold down the
(RHYTHM) button until the
displayed Music Preset number and name change
to the rhythm number and name.
(2) Use the
(w, q) buttons to select the rhythm
you want.
(3) Hold down the
(RHYTHM) button again until
the rhythm number and name change back to the
Music Preset number and name.
• To change the tone, use the
through
(tone
group) buttons to select the tone group and then use
the (w, q) buttons to select a tone number.
Editing operation type
4.
To exit a Music Preset, press
(MUSIC PRESET) at the same time.
and
E-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Music Presets
4.
Edit the Music Preset parameters.
8.
Enter a name for the preset.
Use the
(u) and
(i) buttons to move the cursor
4-1.To edit the chord progression
Press the (w) down button to display
to the character you want to change and then use the
(w, q) buttons to change the character. The
following shows a table of available characters.
• To input a space, press both of the
buttons at the same time.
“CHORD” and then press the
(ENTER)
button to advance to the chord progression
editing screen.
(w and q)
Next, perform the editing operation described
under “To edit the chord progression” (page
E-29). After you finish the editing operation,
press the
(EXIT) button to return to the
screen for selecting the type of editing
operation, above.
4-2.To edit Auto Accompaniment parameters
Press the
(q) up button to display
“Parameter” and then press the
(ENTER)
button to advance to the Auto
Accompaniment parameter editing screen.
Next, perform the editing operation described
under “To edit Auto Accompaniment
parameters” (page E-31). After you finish the
9.
Press the
This saves the data.
(ENTER) button.
editing operation, press the
(EXIT) button
to return to the screen for selecting the type of
editing operation, above.
• If the preset number where you are saving the data
already has data saved to it, a message (Replace?) will
appear on the display to confirm whether you want
to replace the existing data with the new data. Press
5.
6.
After editing everything you want, press the
the
(YES) button to replace. To cancel the save
operation and return to the screen in step 6, press the
(NO) button instead.
(EXIT) button.
• This will display a message asking if you want to
save the user preset.
Press the
(YES) button.
This displays a screen for selecting the Music Preset
number and name for storing the edited data.
• If you do not want to save the edited data, press the
(NO) button in place of the
(YES) button.
Music Preset name
Music Preset number for data storage
7.
Use the
(w, q) buttons to select the
Music Preset number where you want to
store the edited data.
E-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Music Presets
■ To edit the chord progression
2.
3.
Use the
(REW) and
(FF) buttons to
move the cursor (2) on the chord progression
editing screen to the step you want to select.
1.
On the editing operation selection screen
(page E-27), select “CHORD” and then press
the
(ENTER) button to display the chord
Change the content of the selected step as
desired.
progression editing screen shown below.
3-1.Select a chord fingering mode and use the
chord keyboard (page E-18) to input chords.
Fingering a chord causes the cursor (2) to
move to the next step automatically.
• If you want to advance to the next step
without changing the current chord, press
the
(PAUSE) button.
(2) Cursor
(1) Step (timing and chord)
(3) Resolution
• If (3) Resolution is shorter than the time up
to the next step, a new step (without chord)
that is equal to the time of the resolution
will be inserted temporarily into the Music
Preset. Fingering a chord for the new step
will cause the step to be registered as part
of the Music Preset, and the cursor will
advance to the next step.* You can use this
operation to insert a new step between the
current and following step.
(1) Step (timing and chord)
The timing of a chord progression is expressed as a
series of three values separated by colons (such as
001:1:00) indicating measure*1 (001), beat (1), and
tick (00).*2 This series of three values is referred to
collectively as a “step”.
The screen shot above shows the first two steps
(001, 002) of the Music Preset. Use the (REW) and
* Using the
(REW) and
(FF) buttons to
(FF) buttons to scroll and view other steps.
move the cursor without inputting a chord
will delete the temporarily inserted step.
*1 Up to 999 measures
*2 There are 12 ticks per beat, as shown below.
3-2.Use the
(w, q) buttons to change the
Chord progression
step timing (measure:beat:tick).
Each press of either button changing the
timing in accordance with the resolution.
• The range of values you can specify for the
step timing is limited by the steps before
and after the current step.
• The timing of the first step (001:1:00) is
fixed and cannot be changed. Also, the final
step is always one measure, regardless of
the resolution.
Measure 1
Beat 2 Beat 3
Measure 2
Beat 2
Beat 1
Beat 4
Beat 1
002:1:00
Tick
00 01 02
09 10 11
For the sample display
above, the chord change
from C to Bm occurs here.
001:1:00
(2) Cursor
Specifies the step that is currently selected for
editing.
(3) Resolution
Resolution is a unit used when editing step timing.
The initial resolution is R1 (one measure), but you
also can select R4 (1 beat = 4 quarter notes) when
you want to specify chords for each beat. Use the
Last step
instrument part buttons ( through ) to select
one of the eight resolutions shown below.
3-3.To delete a step, press both of the
(w and
q) buttons at the same time.
ck
cl
cm
cn
co
cp
cq
cr
• You cannot delete the first step or the last
step.
R1
R2
R4
R8
R8T
3
R16
R16T
3
R32T
3
(1 measure)
(2 beats)
(1 beat)
(1/2 beat)
(1/3 beat)
(1/4 beat)
(1/6 beat)
(1/12 beat)
E-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Music Presets
4.
Repeat the above steps to edit all of the steps
you want.
• You can playback the Music Preset you are currently
editing by pressing the
(START/STOP) button.
• The table below describes other Music Preset editing
operations you can perform. Press the
(u) and
(FUNCTION) button, use the
(i)
buttons to select the editing operation you want,
perform the required operation, and then press the
(ENTER) button to apply the edit and return to the
chord progression editing screen.
• To exit the editing operation and discard all of your
edits, press the
(EXIT) button.
Editing
Operation
(Display)
Description
Operation
Initializes all steps.
Initialization is
useful when you
want to create a
totally new chord
progression from
scratch.
Initialize
(Initialize)
1
–
Changes the pitch
Use the
(w, q)
Change Key (key) of the chords
buttons to select the
2
3
(Change
Key)
in all of the steps in amount of change
semitone units.
you want (–5 to 6
semitones).
Copies all of the
steps of another
Music Preset to the
end of the current
Music Preset.
Use the
(w, q)
Append
buttons to select the
number of the Music
Preset you want to
add.
Music Preset
(Append
Chords)
Delete
Deletes a specified
Use the
(w, q)
Measures
(DELETE
Measure)
number of measures buttons to select the
4
5
from the current
measures.
cursor step forward.
Insert
Inserts a blank
measure at the
currently selected
step.
Measure
(INSERT
1Measure)
–
* The Music Presets in groups B, C, and D are
numbered sequentially, following the numbers in
group A, which start with 001. For details about
sequential numbers, see the “Music Preset List” on
page A-7.
5.
After all editing operations are complete,
press the (EXIT) button to return to the
editing operation selection screen (page
E-27).
NOTE
• A single preset can contain up to approximately
2,000 chords. If your edits cause the chord limit to be
exceeded, the message “Memory Full” will appear
on the display and further editing will become
impossible.
E-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Music Presets
■ To edit Auto Accompaniment parameters
1.
On the editing operation selection screen (page E-27), select “Parameter” and then press the
(ENTER) button to display the Auto Accompaniment parameter editing screen shown below.
Setting
Parameter
2.
Use the
setting.
(u) and
(i) buttons to select a parameter, and the (w, q) buttons to change its
Parameter
Description
Setting
0 Off: Off (no standby)
SYNCHRO TYPE:
Synchro type
Selects the synchro standby status and type
when the Music Preset is selected.
1 Normal: From standby to normal pattern
2 Variation: From standby to variation pattern
3 Intro: From standby to intro pattern
1
DRUM ON/OFF:
Drum on/off
OFF: Mutes the part.
ON: Sounds the part.
2
3
4
Toggles the drum part (page E-21) on or off.
PERC ON/OFF:
Percussion on/off
Toggles the percussion part (page E-21) on or OFF: Mutes the part.
off.
ON: Sounds the part.
BASS ON/OFF:
Bass on/off
OFF: Mutes the part.
ON: Sounds the part.
Toggles the bass part (page E-21) on or off.
CHORD1 - 5
5 - 9 ON/OFF:
Toggles the Chord 1 through 5 parts (page
E-21) on or off.
OFF: Mutes the parts.
ON: Sounds the parts.
Chord 1 - 5 on/off
INTRO CHORD:
Intro chord
Selects from among major (× 12 keys) and
minor (× 12 keys) for the intro chords.
C - B: Major (C to B)
Cm - Bm: Minor (Cm to Bm)
10
11
ENDING CHORD:
Ending chord
Selects from among major (× 12 keys) and
minor (× 12 keys) for the ending chords.
C - B: Major (C to B)
Cm - Bm: Minor (Cm to Bm)
Specifies whether or not a fill-in should be
inserted into the final measure of a chord
progression.
AUTO FILL-IN:
Auto fill-in on/off
OFF: Fill-in not inserted
ON: Fill-in inserted
12
1 Normal: Edited chord progression proceeds
as-is.
• This parameter lets you add different
variations to the timing of the chord
progression being edited. You can use it to
2 Half: Halves chord timing within a measure.
3 Double: Doubles chord timing within a
measure.
TIMING SET:
13 Chord progression
variation
match the chord progression to the beat of a 4 3/4: Multiplies chord timing within a measure
specific rhythm.
• A chord (step) that is outside of the rhythm’s
beat is cut off.
by 3/4. Select this setting to match to a
6/8 time rhythm.
5 6/4: Multiplies chord timing within a measure
by 3/2. Select this setting to match to a
6/4 time rhythm.
3.
After all editing operations are complete, press the
selection screen (page E-27).
(EXIT) button to return to the editing operation
E-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering Tone and Rhythm Setups
btw, q
brREGISTRATION
–
Tone and accompaniment areas
dmSTORE
–
Tone areas
Registrations let you save Digital Piano setups (tone,
rhythm, tempo, etc.) and for quick and easy recall
when you need them.
■ Registration Data Types
Tone Settings
• Tone numbers (main, layer, lower split)
• Layer on/off
• Layer balance
• Split on/off
• Split point
• Octave shift
• Brightness
• Reverb
Registrations are stored using eight banks of 12 areas
each as shown in the illustration below, for a total of 96
setups. Areas A through D on the left (tone and
accompaniment area) is for storing tones and Auto
Accompaniment settings, while areas 1 through 8 (tone
areas) are for storing tone settings only.
• Chorus
• Transpose
• Touch response
Tone and
accompaniment area
Tone area
A
B
C
D
1
2
3
4
5
6
7
8
Auto Accompaniment Settings
(Areas A through D only)
• Rhythm number
• Accomp on/off
• Chord fingering mode
• Synchro standby
• Tempo
• Auto Accompaniment volume
• Auto harmonize
1
2
3
4
5
6
7
8
Banks
Bank 7, Area B data
Bank 3, Area 2 data
Tone Settings
Keyboard Tone:
003 Harpsichord
Brightness: 2
Reverb: 1 Room
Chorus: Off
·
Tone Settings
Keyboard Tone:
002 Electric Piano2
Brightness: –1
Reverb: 4 Stadium
Chorus: 1 LightChorus
·
·
·
Auto Accompaniment
Settings
Rhythm: 005 Pop Rock
Tempo: 180
Accompaniment Volume: 35
·
·
E-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering Tone and Rhythm Setups
Saving Registration Data
Recalling a Registration
1.
Configure the Digital Piano with the tone,
rhythm, and other settings you want to save.
1.
Press the
lower lamp is lit.
(REGISTRATION) button so its
This enters the registration recall mode.
2.
While holding down the
(STORE) button,
use the (w, q) buttons to select the bank
where you want to save the registration.
Example: Bank 4
Lit
3.
Next, hold down the
(STORE) button
again as you use the rhythm group buttons
through ) or instrument part buttons (
2.
3.
Use the
(w, q) buttons to select the
(
bank where the registration you want to recall
is located.
through ) to select an area.
The data will be saved to the bank and area you specify.
Use the rhythm group buttons ( through
or instrument part buttons ( through ) to
)
Tone and
accompaniment area
specify the area.
This will configure the Digital Piano with the
registration data located at the bank and area you
specified.
Example: When recalling the registration data in Bank
4, Area C
Tone area
Example: Bank 4, Area C
Area
E-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Keyboard Play
6START/STOP
9RECORDER
btw/NO, q/YES
ctu
bsFUNCTION csEXIT dki
You can record your music as you play and store up to
five songs in Digital Piano memory for later playback.
You can divide a song into parts (by instrument, by left
hand and right hand, etc.) and record each part
separately. You can even use “punch-in recording” to
edit specific parts of existing recordings.
3.
4.
Play something on the keyboard.
Recording starts as soon as you play something.
• If Auto Accompaniment is playing, it will be
included in the recorded data.
When you are finished, press the
STOP) button.
(START/
This will cause the
then light, indicating the playback mode.
• If you are using Auto Accompaniment, you also can
end the recording session by pressing the
(RECORDER) lamp to flash and
Recording or Playing Back a
Single Song
(ENDING) button.
The following are the steps for recording or playing
back a single recorder memory song.
Lit: Playback mode
1.
Press the
its lamp is flashing.
(RECORDER) button twice so
This turns on the recorder and enters record mode.
5.
6.
To play back what you have recorded, press
(START/STOP) again.
• Each press of the
through modes as shown below.
(RECORDER) button cycles
• Each press of
starts and stops playback.
Recorder Off
Recorder On
Unlit
Flashing: Record mode
Lit: Playback mode
To turn off the recorder, press the
(RECORDER) button so its lamp goes out.
Unlit: Recorder off
2.
Configure the tone, rhythm, and other
settings you want to use.
• The settings you configure here will be included as
part of the recorded song data.
• For details about what is included in the recorded
song data, see “System Track” (page E-35).
E-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Keyboard Play
5.
6.
To record to the currently selected song,
NOTE
press the
(RECORDER) button. To play
• Recorder memory capacity is approximately 10,000
notes per song. When remaining capacity is 100
notes or less, the
flash at high speed. Recording will stop
automatically when memory becomes full.
• Repeat, fast reverse, fast forward, pause, and tempo
adjustment during playback are the same as when
playing back songs. See “Playing Back a Specific
Music Library Song” (page E-24) for more
information.
back the currently selected song, press the
(START/STOP) button.
(RECORDER) button lamp will
If you are recording, continue from step 2
under “Recording or Playing Back a Single
Song” (page E-34).
Recording to a Specific Track
(Part)
• You can listen to the song data currently stored in
recorder memory at any time by pressing the
(RECORDER) button to enter the playback mode
and then pressing
You can record specific instruments, the left hand and
right hand, or other parts of a song individually, and
then combine them into a final song.
(START/STOP).
IMPORTANT!
• A new recording replaces (deletes) previously
recorded contents.
■ What is a track?
• If power to the Digital Piano is cut off while recording
is in progress, everything you recorded up to that
point will be deleted. Take care so power is not
turned off accidentally during recording operations.
A “track” is a separate recorded part of a song. The
recorder of this Digital Piano supports a total of 17
tracks, which are divided between two types described
below.
System Track
Recording or Playing Back
Multiple Songs
In addition to notes you play on the keyboard and
other performance operation data, the system track
also includes a wide range of setup information for
the song, including layer on/off, split on/off, tempo,
Auto Accompaniment settings, reverb on/off, etc.
When you record a single-track song to recorder
memory, as shown under “Recording or Playing
Back a Single Song” (page E-34) and “Recording or
Playing Back Multiple Songs” (page E-35),
everything is recorded to the system track.
You can record up to five songs (numbered 1 through
5) in memory. After that, you can select a specific song
for playback.
1.
Use the
(RECORDER) button to cycle
through the recorder modes until the
playback mode is selected.
Lit: Playback mode
Tracks 01 through 16
These tracks are used to record keyboard notes, tone
settings, and pedal operations. These tracks can be
combined with the system track and each other to
create the final song.
2.
While holding down the
(FUNCTION)
button, press the
(RECORDER) button.
This displays the song selection screen.
3.
4.
Use the
song number you want.
(w, q) buttons to select the
Press the (EXIT) button to exit the song
selection screen.
E-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Keyboard Play
■ Supported Track Data
The following describes the data that can be recorded
to each type of track.
4.
5.
Select the tone of the part you want to record
to the track.
Press the
(START/STOP) button.
System Track, Tracks 01 through 16
Keyboard notes, keyboard tone setting (main), and
pedal operations
This will start playback of what you recorded to the
system track and start recording to the currently
selected track. Play what you want to record to the
current track along with the playback from the system
track.
System Track only
Layer, split, octave shift, reverb, chorus, keyboard
temperament, tempo, Auto Accompaniment play, auto
harmonize, one-touch preset, Music Preset,*1
registration*1*2
6.
To stop recording, press the
STOP) button again.
(START/
This enters the playback mode. Press the
(START/
STOP) button again to play back the track you just
*1 Recall only
recorded. Each press of
stops playback.
(START/STOP) starts and
*2 The Auto Accompaniment volume level and
transpose setting of the recalled data is not included
in the recording.
• You can use the following procedure to turn specific
tracks on (play enabled) and off (play disabled). This
allows you to listen only to the track(s) you want
when recording a new track.
1.
Record the first part to the system track.
(1) While holding down the
(FUNCTION)
• Use the procedure under “Recording or Playing Back
a Single Song” (page E-34) or “Recording or Playing
Back Multiple Songs” (page E-35) to record to the
system track.
button, press the
(RECORDER) button.
This displays the song selection screen.
(2) Press the (i) button once.
This displays the track on/off screen.
(3) Use the
(w, q) buttons to select the track
2.
Use the
(RECORDER) button to cycle
you want, and then press the
to toggle it on or off.
(ENTER) button
through the recorder modes until the
RECORDER lamp is flashing (record mode).
Flashing: Record mode
7.
Repeat steps 2 through 6 as required to
record all of the tracks you want.
3.
While holding down the
(FUNCTION)
button, press the
(RECORDER) button.
This displays the track selection screen.
Use the ) button to select the track you
(
,
w q
want to record next (T01 through T16).
After selecting a track, press the
exit the track selection screen.
(EXIT) button to
Track Name
Display
System Track
Sys
Tracks 01 through 16
T01 through T16
E-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Keyboard Play
Deleting a Recorder Song Track
Deleting Recorder Data
1.
Perform steps 1 through 3 of the procedure
under “Deleting a Recorder Song” to select
the recorder song that contains the track you
want to delete.
You can use the procedures below to delete an entire
recorder song or to delete a specific track of a recorder
song.
Deleting a Recorder Song
2.
3.
4.
Press the
This displays the track selection screen.
(i) button.
1.
Use the
(RECORDER) button to cycle
through the recorder modes until the
RECORDER lamp is lit (playback mode).
Lit: Playback mode
Use the
(w, q) buttons to select the
track you want to delete.
Hold down the (RECORDER) button until
the message “Sure?” appears on the display.
5.
Press the (YES) button to delete the track.
2.
While holding down the
(FUNCTION)
• To cancel the delete operation, press the
(NO)
button.
button, press the
(RECORDER) button.
This displays the recorder song selection screen.
Re-recording Part of a
Recorder Song
3.
4.
5.
Use the
(w, q) buttons to select the
recorder song you want to delete.
(Punch-in Recording)
Hold down the (RECORDER) button until
the message “Sure?” appears on the display.
You can use punch-in recording to re-record a specific
part of recorder song that you want to improve or
correct.
Press the (YES) button to delete the
recorder song.
Mistake
• To cancel the delete operation, press the
button.
(NO)
Playback
Use punch-in
recording to re-record
only this part.
1.
2.
Turn on the recorder, enter the record mode,
and select the track that contains the section
you want to re-record.
• See step 3 under “Recording to a Specific Track
(Part)” (page E-35).
Hold down the
(RECORDER) button until
the punch-in recording screen appears on the
display.
E-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Keyboard Play
3.
Press the
This will start playback of the selected track.
(START/STOP) button.
Specifying the Punch-in Recording
Location (Auto Punch-in Recording)
You can use the following procedure to specify a
particular range for punch-in recording.
4.
When playback reaches the point you want to
re-record, play the notes and perform the
other operations you want.
Start measure
End measure
This automatically starts punch-in recording, which
will continue until step 5, below.
• Any one of the following also will start punch-in
recording: a pedal operation; pressing the
Punch-in recording range
(RECORDER) button;*1 changing the tone setting;
changing the rhythm or tempo setting*2.
*1 Press
(RECORDER) when you want to start
1.
Turn on the recorder, enter the record mode,
and display the recording setup screen.
punch-in recording without note input or a setting
change.
*2 System track only
• You can perform
• While holding down the
(FUNCTION) button,
press the
(RECORDER) button.
(REW),
(FF), and
(PAUSE)
button operations during punch-in playback to jump
more quickly to the section you want to re-record.
2.
3.
Use the
“AutoPu.IN”, and then use the
buttons to select the start measure.
(
u
) and
(i) buttons to display
(
w
,
q
)
5.
To stop punch-in recording, press the
(START/STOP) button again.
Anything in the track following the point where you
Use the (u) and (i) buttons to
display “AutoPu.OUT”, and then use the
(w, q) buttons to select the end measure.
pressed the
as-is.
(START/STOP) button will be retained
• If you want to delete all of the data in the track
• After selecting the start and end measures, press the
following the section you re-recorded with punch-in
(EXIT) button to exit the recording setup screen.
recording, press the (RECORDER) button in place
of the
(START/STOP) button above.
4.
5.
Select the track that contains the range of
measures you want to re-record.
• See step 3 under “Recording to a Specific Track
(Part)” (page E-35).
• If you want to cancel punch-in recording and retain
the original (unedited) track data, hold down the
(RECORDER) button until the display exits the
punch-in recording screen.
Hold down the
(RECORDER) button until
the punch-in recording screen appears on the
display.
6.
7.
Press the
punch-in recording.
(q) button to turn on auto
Press the
playback.
(START/STOP) button to start
• Punch in recording will start from the start measure
and stop with the end measure automatically.
8.
Play the notes and perform the other
operations you want.
E-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Keyboard Play
■ Performing Punch-in Recording for Areas
Smaller than One Measure
Use the procedure below to specify a punch-in
recording area that includes a part of a measure.
Example: To re-record from beat 3 of measure 2 up to beat
1 of measure 4
To re-record this section
1.
2.
Start playback of the song that contains the
section you want to re-record.
When playback reaches the beginning of the
section you want to re-record, press the
(REPEAT) button.
3.
When playback reaches the end of the
section you want to re-record, press the
(REPEAT) button again.
4.
5.
Press the
playback.
(START/STOP) button to stop
Turn on the recorder and select the track that
contains the section you want to re-record.
• For information about selecting a track, see step 3
under “Recording to a Specific Track (Part)” (page
E-35).
6.
Hold down the
the punch-in recording screen appears on the
display.
(RECORDER) button until
7.
8.
9.
Press the
punch-in recording.
(q) button to turn on auto
Press the
repeat.
(REPEAT) button to turn on
Press the
(START/STOP) button.
This starts punch-in playback from the measure before
the location (start point) you specified in step 2, above.
• Punch-in recording starts automatically when
playback reaches the start point and ends
automatically when it reaches the location you
specified in step 3 (end point).
E-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Settings
btw, q
bsFUNCTION
dki
ctu
You can use the settings in this section to adjust the
tuning and touch of the keyboard, to configure pedal
and MIDI settings, and to configure other parameters
in order to tailor Digital Piano operation to your
particular needs.
NOTE
• Holding down the
you press the
scroll the setting in steps of 10.
• You also can use the (FUNCTION) button for
(FUNCTION) button while
(w, q) buttons in step 3 will
faster scrolling while changing the tone number,
rhythm number, and other scrollable settings.
Configuring Settings
• Keep the
while pressing a
speed scrolling. Releasing the
(FUNCTION) button depressed
(w, q) button for high-
1.
Press the
(FUNCTION) button.
(FUNCTION)
The FUNCTION lamp will light and the function screen
will appear on the display. (See table below.)
button first can result in another unintended
setting being changed.
Parameter or group
Setting
2.
Use the
(u) and
(i) buttons to select
one of the parameters (1 through 8) shown in
the table below.
• Parameters 4 through 8 actually are parameter
groups. After selecting a group, press the
(ENTER) button, and then use buttons (u) and
(i) to select the parameter you want.
• Short cut buttons also are available for accessing a
parameter directly after you press the
(FUNCTION) button, without going through the
menu. See the “Shortcut Button” column in the table
below for the applicable shortcut button of each
parameter.
3.
Use the
(w, q) buttons to change the
setting of the currently selected parameter.
• To return to the function screen, press the
(EXIT)
or
(FUNCTION) button.
E-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Settings
Display
Name
Shortcut
Button*
No.
Parameter
Description
Settings
1
Keyboard Key (Transpose)
Transpose
Adjusts keyboard tuning by semitone
units.
–12 to 00 to 12 semitones
–99 to 00 to 99 cents
2
3
Keyboard Fine Tuning
(Tuning)
Tune
Adjusts keyboard tuning by cent
(1 semitone = 100 cents) units.
Keyboard Touch (Touch
Response)
Touch
Adjusts keyboard touch.
Off: Off
1: Strong sound even
with light pressure
2: Normal
–
3: Normal sound even
with strong pressure
4
Volume Level Group
4-1 Layer Balance
Volume
LayerBal.
Adjusts the volume balance of two tones
layered using the Layer function (page
E-9).
To lower the volume of the layered tone,
set a negative value. To lower the volume
of the main tone, set a positive value.
–24 to 00 to 24
4-2 Auto Accompaniment
Volume
AccompVol.
SongVol.
Adjusts the volume level of Auto
Accompaniment without changing the
keyboard tone volume level.
00 to 42
–
4-3 Song Volume
Adjusts the volume level of song playback 00 to 42
without changing the keyboard tone
volume level.
–
4-4 Metronome Volume
Temperament/Effect Group
5-1 Temperament
MetroVol.
Tmpr/Effect
Temper.
See page E-14.
00 to 42
–
5
Changes the temperament of the
<Temperaments>
keyboard and Auto Accompaniment from 00: Equal / 01: Pure Major /
the standard equal temperament to
another tuning more suitable for playing
classics, etc.
02: Pure Minor /
03: Pythagorean /
04: Kirnberger 3 /
• Pressing a keyboard key while the
temperament screen is displayed will
make the pressed key the base note of
the temperament.
05: Werckmeister /
06: Mean-Tone / 07: Rast /
08: Bayati / 09: Hijaz /
10: Saba / 11: Dashti /
12: Chahargah / 13: Segah /
14: Gurjari Todi /
–
15: Chandrakauns /
16: Charukeshi
<Base notes>
C to B (12 types)
5-2 Accompaniment
Temperament
AccompTmpr Turn this setting off to play Auto
Accompaniment patterns using standard
equal temperament (00: Equal), regardless
of the temperament setting currently
selected with the Temperament parameter
(5-1).
Off, On
–
5-3 Stretch Tuning
Stretch
Sharpens high notes and flattens low
notes to achieve stretch tuning. Turn off
this setting to play with normal (non-
stretch) tuning.
Off, On
–
–
5-4 Brilliance
Brilliance
See page E-11.
–3 to 0 to 3
Off, On
5-5 Acoustic Resonance
AcoResona.
Reproduces the acoustic resonance that
occurs when the damper pedal is
depressed on a grand piano.
No acoustic resonance is applied when
this setting is turned off.
–
5-6 Octave Shift
5-7 Duet Mode
OctShift
Duet
See page E-11.
U1 : –2 to 0 to 2
U2 : –2 to 0 to 2
L1 : –2 to 0 to 2
–
See page E-14.
Off, On
–
*
– in this column means, “While holding down , press .”
B
E-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Settings
Display
Name
Shortcut
Button*
No.
Parameter
Description
Settings
6
Song Playback/Card Group
6-1 Pre-count
Play/CARD
PreCount
Turn on this setting for an audible count
before starting playback of a song.
Off, On
–
6-2 Song Repeat
6-3 Card Folder
SongRepeat
Turn on this setting to repeat play a song. Off, On
(Folder Name)
–
CARD Folder See page E-53.
–
to
6-4 Formatting a Memory
Card
CARD
FORMAT
See page E-45.
–
–
6-5 Card File Delete
6-6 Card File Rename
MIDI Group
File DELETE
See page E-47.
–
–
–
–
File RENAME See page E-47.
MIDI
7
7-1 Keyboard Channel
KeyboardCh
Selects the keyboard channel, which is the 01 to 16
channel used to send MIDI data
–
corresponding to Digital Piano keyboard
play to an external device.
7-2 Accomp MIDI Out
AccompOut
ChordJudge
Turn on this setting to send MIDI data
corresponding to Auto Accompaniment
to an external device.
Off, On
Off, On
–
–
–
7-3 MIDI In Chord Judge
Select whether chord input should be
performed when an Auto
Accompaniment chord keyboard MIDI
note on message is received.
7-4 Local Control
LocalCtl.
Turn off this setting to have keyboard
notes sent to an external device without
being sounded by the Digital Piano.
Off, On
8
Other Parameters Group
8-1 Display Contrast
General
Contrast
Adjusts the contrast of the Digital Piano’s 00 to 16
display.
–
8-2 Panel Lock
PanelLock
BackUp
Turn on to lock the Digital Piano’s control Off, On
panel to prevent unauthorized or
accidental operation.
• This setting is disabled while the
recorder is on, or while Auto
–
–
Accompaniment, a song, or the
metronome is playing.
8-3 Setting Backup
Switching this setting from off to on will
save various Digital Piano settings in
effect at that time, and restore them the
next time the Digital Piano is turned on.
• This operation is disabled in the Duet
Mode, while the recorder is on, or while
Auto Accompaniment, a song, or the
metronome is playing.
Off, On
*
– in this column means, “While holding down , press .”
B
E-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Memory Card
6PLAY/STOP
7PART
btw/NO, q/YES
bsFUNCTION
dlCARD/INTERNAL, ENTER
–
Folders
ctu dki
dnSD CARD SLOT
You can use the procedures in this section to transfer
edited Auto Accompaniment data, recorder data, and
other data from the Digital Piano to a commercially
available SD memory card for storage. You also can use
a memory card to transfer standard MIDI files (SMF),
and accompaniment data you downloaded from the
CASIO website from your computer to Digital Piano
memory. Once you do, you can use them as user songs
and user rhythms.
■ Types of Data
Supported
Operations
Description
(File Name Extension)
Load
Data Type
Save to
Memory
Card
from
Memory
Card
User
rhythms
Auto Accompaniment
data edited with this
O
O
O
O
(page E-20) Digital Piano (AC7)
Use a memory card with a capacity of 2GB or less.
Use of a card with a capacity that is greater than
2GB or other types of memory cards is not
supported.
User songs One of the following two
(page E-24) types of music data
1. CASIO format data
(CM2)
–
In this manual, mentions of a “memory card” refer
2. Standard MIDI files
(MID)
SMF Format 0 or
to an SD memory card.
Format 1
User Music Music Preset data edited
Presets
on this Digital Piano
O
(page E-27) (MPS)
Recorder
songs
(page E-34)
Song data recorded on
this Digital Piano (CSR)
O*
O
O
Registration Tone and rhythm setup
(page E-32) settings (CR6)
O
* Can be saved as a standard MIDI file (SMF format 0).
E-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Memory Card
Card and Card Slot Precautions
IMPORTANT!
Loading and Removing a
Memory Card
• Be sure to observe the precautions provided in the
documentation that comes with the memory card.
• Memory cards have a write-protect switch. Use it
when you want to protect the data on the card from
accidental deletion.
• Avoid using a memory card under the following
conditions. Such conditions can corrupt data stored
on the memory card.
• Areas subjected to high temperature, high
humidity, or corrosive gas
• Areas subjected to strong electrostatic charge and
digital noise
IMPORTANT!
• A memory card must be positioned correctly when
being loaded into the Digital Piano. Trying to force
an improperly oriented memory card into the slot can
damage the memory card and the slot.
1.
With the top of the memory card facing
upwards (so you can see it), carefully insert it
into the Digital Piano’s memory card slot (
until stops with a click.
)
• Never touch the contacts of a memory card when
loading it or removing it from the Digital Piano.
• Never eject the memory card while data is being
written to or loaded from it. Doing so can corrupt the
data on the memory card and damage the memory
card slot.
• Never insert anything besides a memory card into
the card slot. Doing so creates the risk of
malfunction.
Top
• Electrostatic charge from your fingers or the memory
card to the card slot can cause malfunction of the
Digital Piano. If this happens, turn the Digital Piano
off and then back on again.
A memory card can become quite warm after very
long use in the memory card slot. This is normal and
does not indicate malfunction.
2.
To remove the memory card first press it into
the slot further.
This will cause the memory card to disengage and eject
partially. Pull the memory card the rest of the way out
of the slot.
E-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Memory Card
Formatting a Memory Card
Saving Digital Piano Data to a
Memory Card
IMPORTANT!
Use the following procedure to save Digital Piano data
to a memory card.
• Format a memory card before using it for the first
time.
• Recorder songs can be saved as a standard MIDI file
(SMF format 0).
• User songs (downloaded songs, etc.) cannot be
saved to a memory card.
• Before formatting a memory card, make sure it does
not have any valuable data stored on it.
• The memory card format operation performed by this
Digital Piano is a “quick format”. If you want to
completely delete all of the data on the memory
card, format it on your computer or some other
device.
1.
2.
Insert a memory card into the Digital Piano’s
memory card slot.
1.
Insert the memory card you want to format
into the Digital Piano’s memory card slot.
Select the data you want to save to the
memory card.
Make sure the write-protect switch of the memory card
is not in the write-protect position so writing is enabled.
To select this
type of data:*1
Do this:
User rhythms Select from among user rhythms 001
through 010 (page E-20).
2.
While holding down the
(FUNCTION)
button, press the
button.
(CARD/INTERNAL)
User Music
Preset
Select from among user Music Preset
001 through 050 (page E-27).
This displays the format screen.
Recorder songs Select from among recorder songs 1
through 5 (page E-34).
Registrations*2 Press the (REGISTRATION) button
so its lower lamp is lit.
*1 For more information about data types, see page
E-43.
*2 All registration data (8 banks × 12 areas) is saved
3.
4.
Press the
(ENTER) button.
in a single file.
This will display a confirmation message (SURE?).
• If you want to cancel the format operation, press the
3.
4.
Hold down the
until the “LOAD” screen appears for the data
you selected.
• You can cancel the LOAD/SAVE operation any time
(CARD/INTERNAL) button
(NO) or
(EXIT) button.
Press the
(YES) button.
• The message “Please Wait” will remain on the
display while the format operation is being
performed. Do not perform any Digital Piano
operation while this message is on the display.
“Complete” appears on the display after formatting
is complete.
by pressing the
(EXIT) button.
Press the
(i) button to switch to the
“SAVE” screen for the data you selected.
• If you are saving a recorder song to a standard MIDI
file (SMF), press the
(i) button again so “SMF” is
displayed on the right side of the screen.
E-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Memory Card
5.
Use the
(w, q) buttons to select the file
Loading Data from a Memory
Card
number (01 to 99) you want to assign to the
data when it is saved to the memory card.
• The file number is the final two characters of the file
name* that appears on the display. By changing this
within the range of 01 to 99 for each save, up to 99
files of the same data type can be stored on the
memory card.
You can use the procedure below to load data from a
memory card into Digital Piano memory.
IMPORTANT!
* The first six characters of the file name indicate the
data type as shown below. These characters are
fixed and cannot be changed.
• Make sure that all of the data you want to load is in
the MUSICDAT folder on the memory card.
Note that if you put data into a music data play-only
folder on a memory card (such as the MUSIC__B
folder), you will no longer be able to load that file into
Digital Piano memory.
File Name
Data Type
(** = file number)
User rhythms
User Music Preset
Recorder songs
Registrations
USRRHY**
USRMPS**
RECSNG**
REGIST**
1.
Insert the memory card into the Digital
Piano’s memory card slot.
2.
Select the data you want to load.
To load this
6.
Press the
(ENTER) button.
Do this:
type of data*
• The message “Please Wait” will remain on the
display while the save operation is being performed.
Do not perform any Digital Piano operation while
this message is on the display. “Complete” appears
on the display after data save is complete.
User rhythms Select from among user rhythms 001
through 010 (page E-20).
User songs
Select from among user songs 001
through 010 (page E-24).
• If there already is a file with the same name on the
memory card, a message (Replace?) will appear
asking if you want to replace it with the new data.
User Music
Preset
Select from among user Music Presets
001 through 050 (page E-27).
Recorder songs Select from among recorder songs 1
through 5 (page E-34).
Press the
(YES) button to replace or the
(NO)
button to cancel the save operation.
Registrations
Press the (REGISTRATION) button
so its lower lamp is lit.
■ Memory Card Data Storage
The above procedure stores Digital Piano data in a
folder named MUSICDAT on the memory card.
• The MUSICDAT folder is created automatically
when you format the memory card on the Digital
Piano (page E-45).
• Note that files not in the MUSICDAT folder cannot
be loaded, deleted, or renamed by this Digital Piano.
You also will not be able to load or delete any file
stored in any subfolder inside the MUSICDAT
folder.
* For more information about data types, see page
E-43.
3.
Hold down the
until the “LOAD” screen appears for the data
you selected.
(CARD/INTERNAL) button
• You can cancel the LOAD/SAVE operation any time
by pressing the
(EXIT) button.
4.
5.
Use the
you want.
(w, q) buttons to select the file
Press the
(ENTER) button.
• The message “Please Wait” will remain on the
display while the load operation is being performed.
Do not perform any Digital Piano operation while
this message is on the display. “Complete” appears
on the display after data loading is complete.
• If there is already data in the destination you are
loading to, a message (Replace?) will appear asking if
you want to replace it with the new data. Press the
(YES) button to replace or the
(NO) button to
cancel the load operation.
B
E-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Memory Card
Deleting Memory Card Data
Renaming a Memory Card File
Use the following procedure to delete memory card
data (files).
Use the following procedure to change the file name of
a file on a memory card.
1.
2.
Insert the memory card into the Digital
Piano’s memory card slot.
1.
2.
Insert the memory card into the Digital
Piano’s memory card slot.
While holding down the
(FUNCTION)
While holding down the
(FUNCTION)
button, press the
button.
(CARD/INTERNAL)
button, press the
button.
(CARD/INTERNAL)
This displays the memory card format screen (page
E-45).
This displays the memory card format screen (page
E-45).
3.
4.
5.
Press the
This displays the file delete screen.
(i) button.
3.
Press the
RENAME” is displayed.
button (i) twice so “File
Press the
(ENTER) button.
4.
5.
Press the (ENTER) button.
This displays a screen for changing the file name.
This displays a screen for selecting data for deletion.
Use the
(w, q) buttons to select the file
Use the
(w, q) buttons to select the file
you want.
you want.
6.
Press the
(ENTER) button.
6.
Use the
(i) and
(u) buttons to move
This will display a confirmation message (SURE?).
• If you want to cancel the delete operation, press the
the flashing cursor to the character you want
to change, and then use the (w, q)
buttons to change the character.
• The characters you can select are shown below.
(NO) or
(EXIT) button.
7.
Press the
(YES) button.
• The message “Please Wait” will remain on the
display while the delete operation is being
performed. Do not perform any Digital Piano
operation while this message is on the display.
“Complete” appears on the display after deletion is
complete.
0
A
K
U
(
1
B
L
2
3
4
5
F
P
Z
}
6
G
Q
S
7
H
R
&
8
I
9
J
T
'
C
D
E
M N O
S
_
`
V W X
Y
{
)
-
^
@ ~
7.
8.
After the file name is the way you want, press
the (ENTER) button.
This will display a confirmation message (SURE?).
• If you want to cancel the renaming operation, press
the
(NO) or
(EXIT) button.
Press the
(YES) button.
• The message “Please Wait” will remain on the
display while the rename operation is being
performed. Do not perform any Digital Piano
operation while this message is on the display.
“Complete” appears on the display after renaming is
complete.
E-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Memory Card
Playing Back All of the Songs in a Folder
Playing Back a Song from a
Memory Card
You can use the procedure below to play back a user
song (page E-24) stored on a memory card without
loading the song into Digital Piano memory.
Use the procedure below to select one of the four
folders on a memory card and play back all of the
songs in the folder in succession.
1.
2.
While holding down the
(PART) button,
press the
(PLAY/STOP) button.
■ Memory Card Folders
This will start tone demo tune playback (page E-23).
Formatting a memory card on the Digital Piano will
automatically create the four folders shown below. You
put playback song data into any one of the folders. You
can use the four folders to group your music data by
family member, genre, or some other categories. Use
Press the
(CARD/INTERNAL) button.
This will switch from tone demo tune playback to card
tune playback.
• While playback is in progress, you can use the
through
buttons (folders) to switch playback to
buttons
through
(folders) to select a folder.
another folder.
• To stop playback, press the
(PLAY/STOP) button.
Folder Name
MUSICDAT
MUSIC__B
MUSIC__C
MUSIC__D
Button Assignment
(A)
(B)
(C)
(D)
Assigning a Different Folder to a Folder
Selection Button
You can use the following procedure to assign different
folders to folder selection buttons
, , and
.
1.
2.
Store the music data you want to play back in
one of the memory card folders.
1.
While holding down the
button, press the folder selection button (
(FUNCTION)
,
, or ) whose folder assignment you want
Insert the memory card into the Digital
Piano’s memory card slot.
to change.
• This displays the folder assignment screen for the
button you press.
3.
4.
Press the
(CARD/INTERNAL) button.
2.
3.
Use the
(w, q) buttons to select the
Press one of the folder selection buttons (
folder you want to assign to the button.
• You can select any folder on the memory card.
through ) to select the card folder you want.
This will display the song number and song
name of the first song in the folder you
selected.
After selecting a folder, you can rename it if
you want.
• Perform steps 6 through 8 of the procedure under
“Renaming a Memory Card File” (page E-47) to
rename the folder.
5.
6.
Use the
song you want.
(w, q) buttons to select the
Press the (PLAY/STOP) button.
This will start playback.
• Each press of
(PLAY/STOP) starts and stops
playback.
• Fast forward, fast reverse, tempo changes, and other
operations are the same as those during playback of a
user song in Digital Piano memory. For details, see
“Playing Back a Specific Music Library Song” (page
E-24).
7.
To quit memory card data playback, press the
(CARD/INTERNAL) button.
E-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Memory Card
Saving Data to Digital Piano
Memory (Internal Area) Instead
of a Memory Card
Even when you do not have a memory card loaded in
the Digital Piano’s memory card slot, you can save up
to about 16MB of data in the Digital Piano’s internal
memory area. You also can load and delete internal
memory area data using the same procedures that you
use with a memory card.
1.
Remove the memory card from the Digital
Piano’s memory card slot (page E-44).
• Removing the memory card from the slot enables
internal memory area data operations (save, load,
delete, rename, playback).
To do this
Save data to the
Perform this operation
From step 2 under “Saving Digital
internal memory Piano Data to a Memory Card” on
area
page E-45
Load data from
the internal
From step 2 under “Loading Data
from a Memory Card” on page E-46
memory area
Delete data from From step 2 under “Deleting
the internal
Memory Card Data” on page E-47
memory area
Rename a file in
the internal
From step 2 under “Renaming a
Memory Card File” on page E-47
memory area
Play back a song From step 3 under “Playing Back a
in the internal
memory area
Song from a Memory Card” on page
E-48
• The operation in step 4 of the
above procedure is not possible in
the case of internal memory area
song playback.
E-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Memory Card
Error Messages
One of the error messages below appears on the display when a problem occurs.
• All mentions of “memory card” in the following table refer to an SD memory card.
Display
Message
Cause
Required Action
Convert
There is not enough Digital Piano memory available to
Reduce the size of the recorder song data by deleting unneeded
convert a recorder song (page E-34) to SMF data and store tracks (page E-37), if there are any.
it on the memory card.
FileName
Format
You are trying to use the procedure under “Renaming a
Memory Card File” (page E-47) to change to a file name
that already exists on the memory card.
Use a different file name.
1. The current memory card format is not compatible
with this Digital Piano.
1. Format the memory card on the Digital Piano (page E-45).
2. The memory card capacity is greater than 2GB.
3. There is something wrong with the memory card.
2. Use a memory card with a capacity of 2GB or less.
3. Use a different memory card.
MediaFull
Media R/W
1. There is not enough room available on the memory
card.
1. Delete some of the files on the memory card to make room for
new data (page E-47), or use a different card.
2. There is not enough room available in Digital Piano
memory.
2. Delete some or all user data from Digital Piano memory to make
room for new data.
1. Memory card data is corrupted.
1. Use a different memory card.
2. Digital Piano memory is corrupted.
2. Back-up Digital Piano memory data by copying it to your
computer, and then turn the Digital Piano off and then back on
again.
• Note that you may not be able to back-up Digital Piano data
in certain cases.
No Card
1. The memory card is not loaded correctly in the Digital 1. Correctly load the memory card into the memory card slot.
Piano’s memory card slot.
2. The memory card was removed while some operation 2. Do not remove the memory card while any operation is in
was in progress.
progress.
No Data
No File
You tried to save a Digital Piano user area (user rhythm, Select a user area that contains data.
user rhythm song, etc.) that does not contain any data to
the memory card.
1. There is no MUSICDAT folder (page E-46) on the
memory card.
1. Create a MUSICDAT folder on the memory card or format the
memory card on the Digital Piano (page E-45).
2. There is no loadable or playable data in the
MUSICDAT folder, or there is no playable data in a
song playback folder (MUSIC__B, etc.)
2. Move the file you want to load or play into the memory card’s
MUSICDAT folder. For song playback, you can place the song
data into any one of the following folders: MUSIC__B,
MUSIC__C, or MUSIC__D.
Not SMF01
You are attempting to play back SMF Format 2 song data. This Digital Piano supports playback of SMF Format 0 or Format 1
only.
Protect
The memory card is write-protected.
Use the memory card’s write protect switch to enable writing.
ReadOnly
A read-only file with the same name you are trying to use • Use a different name to save the new file.
is already stored on the memory card.
• Remove the read-only attribute from the existing file and
overwrite it with the new file.
• Use a different memory card.
SizeOver
1. The data on the memory card is too big to play.
2. The data you are trying to load is too large.
1. This Digital Piano supports playback of song data files with a
maximum size of 320KB.
2. The following is the maximum data size (per data item) when
loading data into Digital Piano memory.
User rhythm: Approximately 40KB
User Song: 320KB
User Music Preset: Approximately 8KB
WrongDat
1. The memory card data is corrupted.
—
2. The memory card contains data that is not supported
by this Digital Piano.
B
E-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
You can connect the Digital Piano to a computer and
Connecting the Digital Piano
exchange MIDI data between them. You can send play
data from the Digital Piano to music software running
on your computer, or you can send MIDI data from
your computer to the Digital Piano for playback.
to Your Computer
IMPORTANT!
• Make sure you follow the steps of the procedure
below exactly. Connecting incorrectly can make data
send and receive impossible.
Minimum Computer System
Requirements
1.
Turn off the Digital Piano and then start up
your computer.
The following shows the minimum computer system
requirements for sending and receiving MIDI data.
Check to make sure that your computer complies with
these requirements before connecting the Digital Piano
to it.
• Do not start up the music software on your computer
yet!
2.
After starting up your computer, use a
commercially available USB cable to connect
it to the Digital Piano.
Operating System
Windows® XP (SP2 or later)*1
Windows Vista® *2
B connector
Windows® 7 *3
USB cable
(A-B type)
Mac OS® X (10.3.9, 10.4.11 or later, 10.5.6 or later, 10.6.2
or later)
*1 Windows XP Home Edition
Windows XP Professional (32-bit)
*2 Windows Vista (32-bit)
*3 Windows 7 (32-bit, 64-bit)
A connector
Digital Piano USB port
Computer USB port
USB port
3.
Turn on the Digital Piano.
IMPORTANT!
• If this is the first time you are connecting the Digital
Piano to your computer, the driver software required
to send and receive data will be installed on your
computer automatically.
• Never connect to a computer that does not conform
to the above requirements. Doing so can cause
problems with your computer.
4.
5.
Start up your computer’s music software.
Configure the music software settings to
select one of the following as the MIDI device.
CASIO USB-MIDI : (For Windows Vista, Windows 7,
Mac OS X)
USB Audio Device: (For Windows XP)
• For information about how to select the MIDI device,
see the user documentation that comes with the
music software you are using.
IMPORTANT!
• Be sure to turn on the Digital Piano first before
starting up your computer’s music software.
B
E-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
NOTE
Transferring Data between the
Digital Piano and a Computer
You can use the procedure below to transfer edited
Auto Accompaniment data, recorder data, and other
data from the Digital Piano to a computer for storage.
You also can transfer standard MIDI files (SMF), as
well as Auto Accompaniment data you downloaded
from the CASIO website from your computer to Digital
Piano memory.
• Once you are able to connect successfully, there is no
problem with leaving the USB cable connected when
you turn off your computer and/or Digital Piano.
• This Digital Piano conforms to General MIDI Level 1
(GM).
• For detailed specifications and connections that
apply to MIDI data send and receive by this Digital
Piano, see the latest support information provided
by the website at the following URL.
■ Data Types Supported for Data Transfer
Using MIDI
The types of data that can be exchanged with a
computer are the same as those that can be saved to an
SD memory card from the Digital Piano (page E-43).*
* Recorder songs (page E-34) cannot be converted to
SMF data for storage on a computer.
What is MIDI?
The letters MIDI stand for Musical Instrument Digital
Interface, which is the name of a worldwide standard
for digital signals and connectors that makes it possible
to exchange musical data between musical instruments
and computers (machines) produced by different
manufacturers.
For details about the MIDI specifications of this Digital
Piano, see the “MIDI Implementation” document at the
website located at the URL below.
IMPORTANT!
• Turning off the Digital Piano while data is being
saved or loaded can cause all data currently stored
in Digital Piano memory (recorded songs, etc.) to be
deleted. Take care so power is not turned off
accidentally during data save and load operations. If
data is deleted, it will take longer than normal for the
Digital Piano to power up the next time you turn it on
(page E-8).
NOTE
1.
Remove the memory card from the Digital
Piano’s memory card slot (page E-44).
• You will not be able to transfer data between the
Digital Piano and a computer if a card is in the
memory card slot.
• You can alter the Digital Piano’s MIDI setup by
changing the MIDI data send channel or other
settings. For details, see “MIDI Group” (page E-42).
• Use a separately available or commercially available
MIDI cable to connect the MIDI terminals of your
Digital Piano and another electronic musical
instrument for exchange of MIDI data.
• The MIDI terminal cannot be used to exchange data
while the Digital Piano is connected to a computer
via the USB port.
2.
Perform steps 1 through 3 under “Connecting
the Digital Piano to Your Computer” to
connect the piano to your computer (page
E-51).
E-52
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
3.
While holding down the
(FUNCTION)
5.
6.
Double-click “PIANO”.
You now should see five data folders, one for each data
type.
button, press the
button.
(USB DEVICE MODE)
This will enter the storage mode, which enables data
transfer with the connected computer. The
(FUNCTION) button lamp will flash and the display
will appear as shown below.
This folder is not a data folder. You should not try to
use it for normal Digital Piano operation.
• To exit the storage mode at any time, press the
(FUNCTION) button. This is the only button
operation that is supported while the Digital Piano is
in the storage mode.
• You will not be able to enter the storage mode while
any one of the following operations is in progress.
Metronome, Auto Accompaniment, song playback,
recorder (on), Auto Accompaniment editing, Music
Preset editing, data transfer between the Digital
Piano and card
Referring to the table below, open the folder
that corresponds to the type of data you want
to transfer.
To load this
type of data
Open this data
folder
Data File Name
User rhythms
(page E-20)
BIDRHYnn.AC7
(nn: 01 to 10)
RHYTHMAC
MUSICLIB
BIDSNGnn.MID
(nn: 01 to 10)
(SMF Format 0 or
Format 1)
BIDSNGnn.CM2
(nn: 01 to 10)
(CASIO format)
4.
If your computer is running Windows XP,
double-click “My Computer”.*
Under “Devices with Removable Storage”, you should
be able to see a folder representing Digital Piano
memory or the memory card loaded in the Digital
Piano (see below).
User songs
(page E-24)
* Windows Vista, Windows 7:
User Music Presets
(page E-27)
BIDMPSnn.MPS
(nn: 01 to 50)
MUSICPST
RECORDER
REGISTMR
Double-click “Computer”.
Mac OS: Skip step 4 and double-click “PIANO” on
your Mac desktop.
Recorder songs
(page E-34)
BIDRECnn.CSR
(nn: 01 to 05)
Registration
(page E-32)
BIDREGAL.CR6
• Data types and contents are the same as those when
saving Digital Piano data to or loading it from an SD
memory card. See “Using a Memory Card” (page
E-43) for more information.
PIANO drive (Digital Piano memory)
B
E-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
7.
File name extensions (.MID, .CM2, etc.) are
not displayed under initial default Windows
settings. Perform the procedure below to turn
on display of file name extensions.
(1) Open any one of the folders shown on page
E-53.
9.
Press the
storage mode.
• If you are using a Macintosh, drag the PIANO folder
to the Trash and then press the Digital Piano’s
(FUNCTION) button to exit the
(FUNCTION) button.
IMPORTANT!
(2) Perform one of the following operations to
• The message “ERROR, DATA EXCHANGE” will
appear on the display if a problem occurs during
data transfer. If this happens, check the message in
the “STATELOG” folder (page E-53) on the “PIANO”
drive. Next find the same message in the table on
page E-50 of this manual to determine the cause of
the problem and what action you need to take to
avoid it.
display folder information.
• Windows XP:
On the [Tools] menu at the top of the folder
window, select [Folder Options].
• Windows Vista, Windows 7:
On the left side of the folder window, click
[Organize] and then select [Folder and
Search Options].
(3) On the Folder Information window, click the
[View] tab.
(4) Under “Advanced Settings”, clear the “Hide
extensions for known file types” check box and
then click [OK].
8.
After opening a data folder, perform either of
the following operations to transfer data.
8-1. To transfer data from Digital Piano memory
to a computer, perform the required
operation on your computer to copy the data
from the Digital Piano folder you opened in
step 6 of this procedure to another location on
your computer.
8-2. To load data from your computer to Digital
Piano memory, first copy the data you want
to load to the data folder you opened. Next,
rename the file as shown in the “Data File
Name” * column in the table under step 6 of
this procedure.
* The value you assign for “nn” in the data file name in
this case specifies the user number (user rhythm, user
song, recorder song, user preset) you want the data to
be assigned to.
Example: Renaming downloaded song data to
BIDSNG04.CM2 to the MUSICLIB folder will
make the data user song 004.
B
E-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
Playing Back User Song Data by Copying
It to the PIANO Drive
Using Your Digital Piano as a Memory
Card Reader
You can use the procedure below at any time to copy
user song data to the PIANO drive (without putting it
in the MUSICLIB folder) for simplified playback on the
Digital Piano.
You can display the contents of the memory card
currently loaded in the Digital Piano’s card slot and
perform copy, delete, and other card operations from
your computer.
• When you copy a user song data file to the
MUSICLIB folder, you need to rename it according
to specified format (page E-53, step 6). You do not
need to rename the file if you use the procedure
below.
1.
2.
Insert the memory card into the Digital
Piano’s memory card slot.
Perform the procedure starting from step 2 on
page E-52.
In step 4 of the procedure, “SD_MMC” will appear in
place of “PIANO”. You can double-click “SD_MMC” to
display the contents of the card loaded in the Digital
Piano card slot, and change it as you like.
■ Using Auto Accompaniment (Rhythm) Data
from the CASIO Website
You can download other model Auto Accompaniment
data from the “Internet Data Expansion System” of the
transfer it to Digital Piano memory.
CASIO format song data
MIDI file song data
1.
2.
3.
Perform the previous procedure to copy the
user song data file to the PIANO drive.
NOTE
• Since the accompaniment data is for other models,
you may experience some abnormalities when
playing it on this model.
Press the
(FUNCTION) button to exit the
storage mode.
Copyrights
Press the (CARD/INTERNAL) button.
The rights of creators and copyright holders of music,
images, computer programs, databases, and other
data are protected by copyright laws. You are allowed
to reproduce such works for personal or non-
commercial use only. For any other purpose, all
reproduction (including data format conversion),
modification, transfer of reproductions, distribution
over a network, or any other use without permission
of the copyright holder exposes you to claims for
damages and criminal prosecution for copyright
infringement and violation of the author’s personal
rights. Be sure to reproduce and otherwise use
copyrighted works only in accordance with applicable
copyright laws.
This will cause the button’s lamp to light and will the
display the song number and song name of the first
song on the PIANO drive.
4.
5.
Use the
(w, q) buttons to select the
song you want to play.
Press the (PLAY/STOP) button.
This starts playback of the selected song.
• Each press of the (PLAY/STOP) button toggles
between play and stop.
• Fast forward, fast reverse, tempo change, and other
operations are the same as those during playback of a
loaded user song and a song file on a memory card.
6.
When you are finished playing back songs,
press the
(CARD/INTERNAL) button.
B
E-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling the Stand
*
CAUTION
Unpacking
• Assembly of the stand should be performed by
at least two people working together.
• This stand should be assembled on a flat
surface.
• Do not remove the tape securing the keyboard
cover in place until assembly is complete.
Removing the tape can cause the keyboard
cover to open and close during assembly,
creating the risk of personal injury to your hands
and fingers.
PREPARATION
• This stand does not include any of the tools required
for assembly. It is up to you to prepare a large
Philips head (+) screwdriver for assembly.
C
A
• Take care that you do not pinch your fingers
between parts when assembling them.
B
To assemble the stand
D
1.
Unfasten the band
cable to the back of the crosspiece
that bundles the pedal
and
Part
Qty
pull the pedal cord out from the crosspiece.
4
N
6
1
2
1
2
4
Pedal cable
2
2.
Attach the side panels
and
to the
crosspiece . Secure the side panels using
the four screws
.
1
1
• When installing part , slide the brackets
into the
slots in either end crosspiece . If the brackets
not inserted into the ends of the crosspiece
as they will go, the screws
are
as far
will not be able to enter
into the screw holes of the brackets , which can
strip the threads of the screws.
IMPORTANT!
• Cover the screw heads with the caps
.
• If anything is missing or damaged, contact your local
CASIO service provider.
J
• Do not use any screws other than those that come
with the stand. Doing so risks damage to the stand
and/or the Digital Piano.
A
E
J
D
E
3
B
2
E-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling the Stand
3.
Slide the back panel
the side panels.
into the grooves
of
4.
Attach the right side of the back panel
to
the bracket
of the side panel
.
• Secure the back panel in place with a screw
.
C
A
5
C
I
4
IMPORTANT!
• Be sure to check that the back panel
engages correctly with the side panel
bracket
bracket as
5.
Pull the side panel
direction marked with in the illustration
below.
slightly outwards in the
shown in the nearby illustration marked “O”.
Assembling the stand while these brackets are not
engaged correctly (as shown in the illustration
marked “X”) creates the risk of damage to stand
components.
• Check to make sure that the relative positions of the
back panel
bracket and the side panel
bracket
are as shown in the illustration A. This step creates a
slight gap between the side panels and , which
makes it easier to mount the Digital Piano onto the
stand in step 6 below.
Back panel
bracket
B
C
B
C
A
Side panel
bracket
E-57
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling the Stand
6.
Place the piano onto the stand.
7.
First, use the two butterfly bolts
the back of the piano to the stand. Next, use
to secure
IMPORTANT!
the two screws
piano.
to secure the front of the
• In order to ensure you do not get your fingers
pinched between the piano and the stand, grasp the
piano on its sides (not its ends) at the locations
marked with stars () in the illustration.
H
At least 10cm
At least 10cm
K
7
IMPORTANT!
• The butterfly bolts
piano from slipping off the stand. Never use the
and the screws
keep the
piano without the butterfly bolts
installed.
and the screws
8.
Attach the left side of the back panel
to the
bracket
of the side panel
.
• At this time the screws on the bottom of the piano
• When attaching the back panel, place the clip
on
should hook into the cutouts in the stand
the screw
as shown in the illustration below.
brackets
.
Back of piano
8
G
I
Stand side
panel
Bracket cutout
7
B
6
C
E-58
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling the Stand
9.
Next, secure the bottom of the back panel
To connect cables
with the six screws
.
1.
Orienting the pedal plug as shown in the
illustration, plug it into the pedal connector on
the bottom of the piano.
• Secure the pedal cord with the clip
.
Pedal plug
C
F
G
10. Adjust the height adjustment screw
to
does
provide support so the crosspiece
not bow downwards when the pedals are
pressed.
2.
3.
Check to make sure that the POWER button
is in the OFF position (raised). If power is on,
press the POWER button to turn it off.
Plug the power cord that comes with the
Digital Piano into the AC power jack on the
bottom of the Digital Piano.*
* applies to the AP-620BKV and AP-6BPV
9
D
IMPORTANT!
• Pressing the pedals without adjusting the height
adjustment screw can result in damage to the
crosspiece . Always make sure you adjust the
height adjustment screw
pedals.
before operating the
Power Cord
IMPORTANT!
• The shape of the power cord plug and household
power outlet receptacle differ according to country
and geographical area. The illustration shows just
one example of the shapes that are available.
• With the AP-620BK and AP-6BP, the power cord is
hard-wired to the Digital Piano.
B
E-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling the Stand
4.
Plug the power cord into a household power
outlet.
To install the music stand and
headphones hook
1.
Insert music stand
Digital Piano console as shown in the figure
into the groove on the
below.
N
Household power outlet
*
CAUTION
• The screws of the stand can work loose due to
the effects of temperature and humidity changes,
vibration, etc. Because of this, you need to
periodically check the screws for proper
tightness. Retighten any loose screws you find.
• To power the Digital Piano, use a power outlet
that allows easy access when plugging in or
unplugging the power cord.
2.
Install the headphones hook.
2-1. Insert the headphones hook
into the two
holes on the bottom of the piano.
2-2. Use the screw to secure the headphones
hook in place.
2-1
L
2-2
M
E-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Troubleshooting
Problem
Cause
Action
See Page
No sound is produced when I
press a keyboard key.
1. The VOLUME controller is set to
“MIN”.
1. Rotate the VOLUME controller more towards E-8
“MAX”.
2. Headphones or an adaptor plug is
plugged into one of the PHONES
jacks.
2. Disconnect whatever is connected to the
PHONES jack.
E-6
The pitch of the Digital Piano is
off.
1. The Digital Piano’s key setting is
something other than “00”.
1. Change the key setting to “00”, or turn Digital E-41
Piano power off and then back on again.
2. Digital Piano tuning is incorrect.
2. Adjust Digital Piano tuning, or turn the piano
off and then back on again.
E-41
E-41
3. A non-standard temperament setting
is being used.
3. Change the temperament setting to
“00:Equal”, which is the standard modern
tuning.
4. Octave shift is enabled.
4. Change the octave shift setting to 0.
E-11
E-42
Tones and/or effects sound
strange. Turning power off and
then back on again does not
eliminate the problem.
The “Setting Backup” feature is turned
on.
Turn off “Setting Backup”. Next, turn power off
and then back on again.
Example: Note intensity does not
change even though I alter key
pressure.
I cannot transfer data after
connecting the Digital Piano to a
computer.
—
1. Check to make sure that the USB cable is
connected to the Digital Piano and computer,
and that the correct device is selected with
your computer’s music software.
E-51
2. Turn off the Digital Piano and then exit the
music software on your computer. Next, turn
the Digital Piano back on and then restart the
music software on your computer.
I cannot record chord
accompaniment data on my
computer.
Accomp MIDI Out is turned off.
—
Turn on Accomp MIDI Out.
E-42
—
I cannot store data to a memory
card or load data from a memory
card.
See “Error Messages” on page E-50.
Stop song playback, disconnect the USB cable
Playback stops part way through Digital noise from the USB cable or
E-51
while transferring song data from power cord caused data communication from the Digital Piano, and then reconnect it.
my computer.
your computer and Digital Piano to be
interrupted.
Next, try playing back the song again.
If this does not solve the problem, quit the MIDI
software you are using, disconnect the USB
cable from the Digital Piano, and then reconnect
it. Next, restart the MIDI software and then try
playing back the song again.
A tone’s quality and volume
sounds slightly different
depending where it is played on
the keyboard.
This is an unavoidable result of the digital sampling process,* and does not indicate malfunction.
* Multiple digital samples are taken for the low range, middle range, and high range of the original
musical instrument. Because of this, there may be a very slight difference in tonal quality and volume
between sample ranges.
When I press a button, the note
that is sounding cuts out
momentarily or there is a slight
change in how effects are applied.
Performing a button operation while playing with the Duet Mode, Auto Accompaniment, the recorder, or
other functions can cause such phenomena when the Digital Piano switches internal tone effects. It does
not indicate malfunction.
Even though I play on different
The ranges of certain tones are limited, which means that octaves change normally up to a certain low
ranges of the keyboard, the notes note or high note. With such a tone, the notes of the lowest octave will be repeated to the left of the
do not change octaves.
lowest possible note, and the highest octave will be repeated to the right of the highest possible note.
This is due do limitations in the range of the original musical instrument for each tone, and does not
indicate malfunction of the Digital Piano.
E-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Product Specifications
All of the items in these specifications apply to the AP-620BK, AP-620BKV, AP-6BP, and AP-6BPV, unless
specifically noted otherwise.
Models
AP-620BK/AP-620BKV/AP-6BP/AP-6BPV
88-key piano keyboard, with Touch Response (3 types)
128 notes
Keyboard
Maximum Polyphony
Tones
250 (with Layer and Split)
Effects
Reverb (4 types), Chorus (4 types), Brilliance (–3 to 0 to 3), Acoustic Resonance
Metronome
• Beats per measure: 0, 2, 3, 4, 5, 6
• Tempo Range: 20 to 255
Duet
Adjustable tone range: 0 to 3 octaves for the left keyboard; –4 to –1 octaves for the right keyboard
Auto Accompaniment
• Built-in Rhythms: 180
• User Rhythms: Up to 10 (Approximately 40KB* maximum per rhythm)
• One Touch Presets: 180 types
• Auto Harmonize: 12 types
Demo Songs
Music Library
68 (8 tone demo songs; 60 Music Library songs)
• Built-in Songs: 60
• User Songs: Up to 10 (320KB* maximum per song)
Music Presets
Built-in Presets: 300
User Presets: Up to 50 (Approximately 8KB* maximum per preset)
Registration
Recorder
(4 rhythm areas + 8 tone areas) × 8 banks
• Functions: Real-time recording, playback
• Number of Songs: 5
• Number of Tracks: 17 (System Track + Tracks 01 through 16)
• Capacity: Approximately 50,000 notes total (Up to approximately 10,000 notes per song)
• Punch-in recording
Pedals
Damper (with half-pedal operation), Soft, Sostenuto
Other Functions
• Transpose: 1 octave (–12 to 00 to 12)
• Tuning: A4 = 440.0 Hz 99 cents
• Octave Shift: 2 octaves
• Temperaments: 17 types
• Stretch Tune
• Panel Lock
MIDI
16 multi-timbre received, GM Level 1 standard
SD Memory Card
• SD memory card slot
• Supported SD Memory Cards: Up to 2GB
• Functions: SMF playback, file storage, file recall, card format
Inputs/Outputs
• PHONES jacks: Stereo standard jacks × 2
• MIDI OUT/IN terminals
• LINE OUT R, L/MONO jacks: Standard jacks × 2
Output impedance: 2.8K
Output voltage: 1.8V (RMS) MAX
• LINE IN R, L/MONO jacks: Standard jacks × 2
Input impedance: 9.0K
Input voltage: 200mV
• USB port: Type B
• Pedal connector
Speakers
16cm × 2 + 5cm × 2 (Output 30W + 30W)
Power Requirements
AP-620BK/AP-6BP : 120V
AP-620BKV/AP-6BPV : 220-240V
Power Consumption
Dimensions
78W
Digital Piano and Stand: 141.2 (W) × 49.2 (D) × 90.0 (H) cm (55 5/8 × 19 3/8 × 35 7/16 inch)
Weight
Digital Piano and Stand: AP-620BK/AP-620BKV: Approximately 57.1 kg (125.9 lbs)
AP-6BP/AP-6BPV: Approximately 58.2 kg (128.3 lbs)
* Based on 1KB = 1024bytes, 1MB = 10242 bytes
• Specifications and designs are subject to change without notice.
B
E-62
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Operating Precautions
Be sure to read and observe the following operating
precautions.
■ Location
Avoid the following locations for this product.
• Areas exposed to direct sunlight and high humidity
• Areas subjected to temperature extremes
• Near a radio, TV, video deck, or tuner
• The above devices will not cause malfunction of the
product, but the product can cause interference in
the audio or video of a nearby device.
■ User Maintenance
• Never use benzine, alcohol, thinner, or other
chemical agents to clean the product.
• To clean the product or its keyboard, wipe with a
soft cloth moistened in a weak solution of water and
a mild neutral detergent. Wring all excess moisture
from the cloth before wiping.
■ Included and Optional Accessories
Use only accessories that are specified for use with this
product. Use of unauthorized accessories creates the
risk of fire, electric shock, and personal injury.
■ Weld Lines
Lines may be visible on the exterior of the product.
These are “weld lines” that result from the plastic
molding process. They are not cracks or scratches.
■ Musical Instrument Etiquette
Always be aware of others around you whenever using
this product. Be especially careful when playing late at
night to keep the volume at levels that do not disturb
others. Other steps you can take when playing late at
night are closing windows and using headphones.
B
E-63
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix/Apéndice
Tone List/Lista de tonos
Bank
Select
MSB/
MSB de
Selección
de banco
Bank
Select
MSB/
MSB de
Selección
de banco
Group
Name/
Nombre Número
del
grupo
Group
Number/
Program
Change/
Cambio
de
Group
Name/
Nombre Número
del
grupo
Group
Number/
Program
Change/
Cambio
de
Sequential
Number/
Número
Acoustic
Resonance/
Resonancia
acústica
Sequential
Number/
Número
Acoustic
Resonance/
Resonancia
acústica
Tone Name/
Nombre del tono
Tone Name/
Nombre del tono
de
grupo
de
grupo
secuencial
secuencial
programa
programa
GRAND PIANO MODERN
009
010
011
012
013
014
015
016
017
064
065
066
067
068
069
070
071
072
STEEL STR.GUITAR 1
STEEL STR.GUITAR 2
STEEL STR.GUITAR 3
JAZZ GUITAR
25
25
25
26
27
27
27
27
29
48
49
50
48
49
48
50
51
48
001
001
GRAND PIANO MODERN
0
0
48
50
O
O
GRAND PIANO
VARIATION
002
002
003
004
005
006
003
004
005
006
ROCK PIANO
LA PIANO
1
1
1
1
48
49
50
51
O
O
O
O
CLEAN GUITAR
CHORUS CLEAN GUITAR
CRUNCH ELEC.GUITAR 1
CRUNCH ELEC.GUITAR 2
OVERDRIVE GUITAR
MODERN PIANO
DANCE PIANO
GRAND PIANO CLASSIC
001
002
003
004
005
006
007
008
009
010
011
012
GRAND PIANO CLASSIC
MELLOW PIANO
HONKY-TONK
0
0
3
3
0
0
49
51
48
49
52
53
O
O
O
O
O
O
VARIOUS/GM TONES
073
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
BREATHY ALTO SAX
BREATHY TENOR SAX
ALTO SAX
65
66
65
66
71
73
56
57
61
61
62
62
81
81
80
110
15
15
72
107
109
111
77
105
105
104
104
20
15
105
111
110
15
105
72
16
0
49
49
48
48
48
48
48
48
48
49
48
49
48
49
48
56
56
57
56
56
56
57
56
56
57
56
57
56
58
58
56
57
59
59
57
56
0
074
075
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
OCTAVE PIANO
STRINGS PIANO
PIANO PAD
TENOR SAX
CLARINET
ELEC PIANO
FLUTE
001
002
003
004
005
006
007
008
009
013
014
015
016
017
018
019
020
021
ELEC.PIANO 1
4
5
4
2
4
5
4
5
4
48
48
51
48
49
49
50
50
52
TRUMPET
ELEC.PIANO 2
TROMBONE
STEREO BRASS
BRASS SECTION
SYNTH-BRASS
80’S SYNTH-BRASS
SAW LEAD
60’S E.PIANO
E.GRAND 80
DYNO ELEC.PIANO
FM ELEC.PIANO
MELLOW E.PIANO
POP ELEC.PIANO
SYNTH-STR.E.PIANO
MELLOW SAW LEAD
SQUARE LEAD
ER HU
VIBES/CLAVI
001
002
003
022
023
024
VIBRAPHONE
CLAVI
11
7
48
48
48
YANG QIN 1
YANG QIN 2
DI ZI
HARPSICHORD
6
COUPLED
HARPSICHORD
ZHENG
004
025
6
49
SHENG
005
006
026
027
MARIMBA
12
11
48
49
SUO NA
CHORUS VIBRAPHONE
XIAO
ORGAN
PI PA 1
001
002
003
004
005
006
007
008
009
010
011
012
013
028
029
030
031
032
033
034
035
036
037
038
039
040
ROCK ORGAN 1
JAZZ ORGAN
16
17
16
16
16
17
17
16
16
18
16
19
19
49
48
48
50
51
49
50
52
53
48
54
48
49
PI PA 2
SITAR
DRAWBAR ORGAN
ROTARY DRAWBAR
ROTARY ORGAN
PERC.ORGAN
TANPURA
HARMONIUM
SANTUR
SAROD
70’S ORGAN
SHANAI
OVERDRIVE ORGAN
TREMOLO ORGAN
ROCK ORGAN 2
ELEC.ORGAN
SARANGI
KANUN
OUD
NEY
CHURCH ORGAN
CHAPEL ORGAN
ARABIC ORGAN
GM PIANO 1
GM PIANO 2
GM PIANO 3
GM HONKY-TONK
GM E.PIANO 1
GM E.PIANO 2
GM HARPSICHORD
GM CLAVI
O
O
STRINGS/SYNTH-PAD
1
0
001
041
STRINGS
49
48
50
50
50
40
52
54
90
88
88
89
89
90
99
48
48
48
49
50
48
48
48
48
48
49
48
49
49
48
2
0
002
042
043
044
045
046
047
048
049
050
051
052
053
054
055
STRING ENSEMBLE
SYNTH-STRINGS
70’S SYNTH-STR.
80’S SYNTH-STR.
VIOLIN SECTION
CHOIR
3
0
003
4
0
004
5
0
005
6
0
006
7
0
007
GM CELESTA
GM GLOCKENSPIEL
GM MUSIC BOX
GM VIBRAPHONE
GM MARIMBA
GM XYLOPHONE
GM TUBULAR BELL
GM DULCIMER
GM ORGAN 1
GM ORGAN 2
GM ORGAN 3
GM PIPE ORGAN
GM REED ORGAN
GM ACCORDION
GM HARMONICA
GM BANDONEON
GM NYLON STR.GUITAR
8
0
008
SYNTH-VOICE
SYNTH-PAD
9
0
009
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
0
010
FANTASY
0
011
NEW AGE
0
012
WARM PAD
0
013
WARM VOX
0
014
POLYSYNTH PAD
ATMOSPHERE PAD
0
015
0
BASS/GUITAR
0
001
002
003
004
005
006
007
008
056
057
058
059
060
061
062
063
ACOUSTIC BASS
RIDE BASS
32
32
33
33
33
34
38
24
48
49
48
49
50
48
48
48
0
0
FINGERED BASS 1
FINGERED BASS 2
FINGERED BASS 3
PICKED BASS
0
0
0
0
TRANCE BASS
0
NYLON STR.GUITAR
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix/Apéndice
Bank
Select
MSB/
MSB de
Selección
de banco
Bank
Select
MSB/
MSB de
Selección
de banco
Group
Name/
Nombre Número
del
grupo
Group
Number/
Program
Change/
Cambio
de
Group
Name/
Nombre Número
del
grupo
Group
Number/
Program
Change/
Cambio
de
Sequential
Number/
Número
Acoustic
Resonance/
Resonancia
acústica
Sequential
Number/
Número
Acoustic
Resonance/
Resonancia
acústica
Tone Name/
Nombre del tono
Tone Name/
Nombre del tono
de
grupo
de
grupo
secuencial
secuencial
programa
programa
062
063
064
065
066
067
068
069
070
071
072
073
074
075
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
GM STEEL STR.GUITAR
GM JAZZ GUITAR
GM CLEAN GUITAR
GM MUTE GUITAR
GM OVERDRIVE GT
GM DISTORTION GT
GM GT HARMONICS
GM ACOUSTIC BASS
GM FINGERED BASS
GM PICKED BASS
GM FRETLESS BASS
GM SLAP BASS 1
GM SLAP BASS 2
GM SYNTH-BASS 1
GM SYNTH-BASS 2
GM VIOLIN
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
GM SF
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
0
0
0
GM SITAR
GM BANJO
0
GM SHAMISEN
GM KOTO
0
0
GM THUMB PIANO
GM BAGPIPE
0
0
GM FIDDLE
0
GM SHANAI
0
GM TINKLE BELL
GM AGOGO
0
0
GM STEEL DRUMS
GM WOOD BLOCK
GM TAIKO
0
0
0
GM MELODIC TOM
GM SYNTH-DRUM
GM REVERSE CYMBAL
GM GT FRET NOISE
GM BREATH NOISE
GM SEASHORE
GM BIRD
0
0
GM VIOLA
0
GM CELLO
0
GM CONTRABASS
GM TREMOLO STRINGS
GM PIZZICATO
0
0
0
GM HARP
GM TELEPHONE
GM HELICOPTER
GM APPLAUSE
GM GUNSHOT
STANDARD SET 1
STANDARD SET 2
STANDARD SET 3
STANDARD SET 4
ROOM SET
0
GM TIMPANI
0
GM STRINGS 1
0
GM STRINGS 2
0
GM SYNTH-STRINGS 1
GM SYNTH-STRINGS 2
GM CHOIR AAHS
GM VOICE DOO
GM SYNTH-VOICE
GM ORCHESTRA HIT
GM TRUMPET
120
120
120
120
120
120
120
120
120
120
120
120
120
120
1
2
3
8
HIP-HOP SET
9
POWER SET
16
GM TROMBONE
GM TUBA
ELECTRONIC SET
SYNTH SET 1
24
25
GM MUTE TRUMPET
GM FRENCH HORN
GM BRASS
SYNTH SET 2
30
TRANCE SET
31
JAZZ SET
32
GM SYNTH-BRASS 1
GM SYNTH-BRASS 2
GM SOPRANO SAX
GM ALTO SAX
BRUSH SET
40
ORCHESTRA SET
48
NOTE
GM TENOR SAX
GM BARITONE SAX
GM OBOE
• Acoustic resonance (page E-41) is applied only to
tones indicated by “O”.
GM ENGLISH HORN
GM BASSOON
• While sequential numbered tone 065 (STEEL
STR.GUITAR 2) or 066 (STEEL STR.GUITAR 3) is
selected, pressing multiple keys on the far left side of
the keyboard will produce a guitar strumming
sound. It does not indicate malfunction.
• See the “Drum Assignment List” (page A-3) for the
percussion instrument assigned to each keyboard
key when a drum set (Sequential Number 237 to 250)
is selected.
GM CLARINET
GM PICCOLO
GM FLUTE
GM RECORDER
GM PAN FLUTE
GM BOTTLE BLOW
GM SHAKUHACHI
GM WHISTLE
GM OCARINA
GM SQUARE LEAD
GM SAW LEAD
GM CALLIOPE
GM CHIFF LEAD
GM CHARANG
NOTA
GM VOICE LEAD
GM FIFTH LEAD
GM BASS+LEAD
GM FANTASY
• La resonancia acústica (página S-41) se aplica
solamente a los tonos indicados mediante “O”.
• Si presiona múltiples teclas en el extremo izquierdo
del teclado mientras están seleccionados los tonos
secuenciales número 065 (STEEL STR. GUITAR 2) o
066 (STEEL STR. GUITAR 3), producirá un sonido
de rasgueo de guitarra. Esto no es ningún signo de
anomalía.
• Consulte la “Lista de sonidos de batería” (página
A-3) para saber cuáles son los instrumentos de
percusión asignados a cada tecla cuando se
selecciona un ajuste de batería (números
secuenciales 237 a 250).
GM WARM PAD
GM POLYSYNTH
GM SPACE CHOIR
GM BOWED GLASS
GM METAL PAD
GM HALO PAD
GM SWEEP PAD
GM RAIN DROP
GM SOUND TRACK
GM CRYSTAL
GM ATMOSPHERE
GM BRIGHTNESS
GM GOBLINS
GM ECHOES
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix/Apéndice
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix/Apéndice
Rhythm List/Lista de ritmos
Group
Number/
Número de
grupo
Sequential
Number/
Número
Group
Number/
Número de
grupo
Sequential
Number/
Número
Group Name/
Nombre del
grupo
Group Name/
Nombre del
grupo
Rhythm name/
Nombre del ritmo
Rhythm name/
Nombre del ritmo
secuencial
secuencial
POPS/JAZZ
059
060
061
062
063
064
065
066
059
060
061
062
063
064
065
066
WALTZ 2
POPS
001
002
003
004
005
006
007
008
009
010
SLOW WALTZ
VIENNESE WALTZ
FRENCH WALTZ
SERENADE
TANGO
MARCH 1
001
002
003
004
005
006
007
008
009
010
POP 1
POP 2
FAST POP
FUNK POP
POP ROCK
6/8 POP
FAST SOUL
SLOW SOUL
60’S SOUL
POP SHUFFLE
MARCH 2
LATIN/WORLD
LATIN I
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
067
068
069
070
071
072
073
074
075
076
077
078
079
080
081
BOSSA NOVA
SLOW BOSSA NOVA
BEGUINE
SAMBA 1
SAMBA 2
MAMBO
RHUMBA
CHA-CHA-CHA
MERENGUE
BOLERO
SALSA 1
SALSA 2
REGGAE
POP REGGAE
SKA
8 BEAT/16 BEAT
011
011
012
013
014
015
016
017
018
019
020
021
STRAIGHT 8 BEAT 1
STRAIGHT 8 BEAT 2
FUNK 8 BEAT
MELLOW 8 BEAT
GUITAR 8 BEAT
8 BEAT
8 BEAT POP
OLDIES 8 BEAT
60’S 8 BEAT
012
013
014
015
016
017
018
019
020
021
16 BEAT
16 BEAT SHUFFLE
DANCE
022
022
023
024
025
026
027
028
029
HIP-HOP
DANCE POP
DISCO POP
TECHNO POP
TRANCE
MODERN R&B
MODERN DANCE
DISCO SOUL
LATIN II
016
023
024
025
026
027
028
029
082
083
084
085
086
087
088
089
090
091
092
REGGAETON 1
REGGAETON 2
CUMBIA
CALYPSO
FORRO
PAGODE
BANDA
PASILLO
ARGENTINE CUMBIA
PUNTA
017
018
019
020
021
022
023
024
ROCK
030
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
STRAIGHT ROCK
SHUFFLE ROCK
BLUES 1
BLUES 2
EP BLUES
SLOW BLUES
SOFT ROCK
LATIN ROCK
SLOW ROCK
50’S ROCK
50’S PIANO ROCK
NEW ORLNS R&R
60’S ROCK
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
025
026
BACHATA
COUNTRY
027
093
094
095
096
MODERN COUNTRY
COUNTRY 8 BEAT
COUNTRY BALLAD
COUNTRY SHUFFLE
FINGER PICKING
COUNTRY
028
029
030
031
097
032
033
WORLD I
AMERICAN
034
098
099
COUNTRY WALTZ
BLUEGRASS
ROCK
70’S PIANO ROCK
ROCK WALTZ
100
101
102
103
104
DIXIE
TEX-MEX
FAST GOSPEL
SLOW GOSPEL
HAWAIIAN
035
036
037
038
JAZZ
046
046
047
048
049
050
051
052
053
054
055
SLOW BIG BAND
MIDDLE BIG BAND
FAST BIG BAND
SWING 1
047
048
049
050
051
052
053
054
SPANISH/EASTERN EUROPEAN
039
040
041
042
043
105
106
107
108
109
PASODOBLE
CAUCASIAN
RUSSIAN CHANSON 1
RUSSIAN CHANSON 2
POLISH WALTZ
SWING 2
SLOW SWING
JAZZ WALTZ
FOX TROT
QUICKSTEP
JAZZ COMBO 1
ARABIC/ORIENTAL
044
045
046
047
048
049
110
SIRTAKI
MUS
ADANI
BALADI
KHALIJI
MALFOOF
055
111
112
113
114
115
EUROPEAN
056
056
057
058
SCHLAGER
POLKA
WALTZ 1
057
058
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix/Apéndice
Group
Number/
Número de
grupo
Sequential
Number/
Número
Group
Number/
Número de
grupo
Sequential
Number/
Número
Group Name/
Nombre del
grupo
Group Name/
Nombre del
grupo
Rhythm name/
Nombre del ritmo
Rhythm name/
Nombre del ritmo
secuencial
secuencial
WORLD II
INDIAN
050
037
038
039
040
041
176
177
178
179
180
PIANO MARCH 2
STRIDE PIANO
WALTZ 3
WALTZ 4
WALTZ 5
116
117
118
119
120
121
122
BHANGRA
DADRA
GARBA
KEHARWA
DANDIYA
TEEN TAAL
BHAJAN
051
052
053
054
055
056
NOTE
• Sequential number rhythms 171 through 180 do not
sound unless a chord is being played.
CHINESE
057
123
124
125
126
127
128
129
130
131
132
133
134
135
136
GUANGDONG
JIANGNAN
BEIJING
DONGBEIYANGGE
JINGJU
HUANGMEIXI
QINQIANG
YUJU
YAOZU
DAIZU
MIAOZU
MENGGU
XINJIANG
ZANGZU
058
059
060
061
062
063
064
065
066
067
068
069
NOTA
• Los ritmos secuenciales números 171 al 180 no
suenan a menos que se ejecute un acorde.
070
SOUTHEAST ASIAN
071
072
137
138
KRONCONG
DANGDUT
JAPANESE
073
139
ENKA
BALLAD/PIANO RHYTHMS
BALLAD
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
PIANO ROCK BALLAD
90’S BALLAD
MODERN BALLAD
ELECTRIC BALLAD
SLOW BALLAD 1
SLOW BALLAD 2
R&B BALLAD
16 BEAT BALLAD
SOUL BALLAD
POP BALLAD 1
POP BALLAD 2
PIANO WALTZ BALLAD
90’S 6/8 BALLAD
6/8 BALLAD 1
6/8 BALLAD 2
ROCK BALLAD
VARIOUS
017
018
019
020
156
157
158
159
160
CHRISTMAS SONG
CHRISTMAS WALTZ
SCREEN SWING
SYMPHONY
021
STR QUARTET
PIANO RHYTHMS
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
PIANO 8 BEAT
PIANO BALLAD 1
PIANO BALLAD 2
EP BALLAD 1
EP BALLAD 2
BLUES BALLAD
JAZZ COMBO 2
JAZZ COMBO 3
RAGTIME
BOOGIE-WOOGIE
PIANO ROCK & ROLL
ARPEGGIO 1
ARPEGGIO 2
ARPEGGIO 3
PIANO MARCH 1
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix/Apéndice
Song List/Lista de canciones
Tone Demo Songs/
Music Library/Biblioteca musical
Canciones de demostración de tonos
Group
Name/
Nombre del Número de
Group
Number/
Sequential
Number/
Número
Song Name/
Nombre de la canción
Tone Group Name/
Number/
Song Name/
grupo
grupo
secuencial
Nombre del grupo de tonos Número
Nombre de la canción
A
GRAND PIANO MODERN
GRAND PIANO CLASSIC
ELEC PIANO
001
002
003
004
005
006
007
008
Prélude [Suite bergamasque]
3 Romances Sans Paroles 3
Original
001
002
003
004
005
006
007
008
009
010
011
012
013
014
001
002
003
004
005
006
007
008
009
010
011
012
013
014
Nocturne Op.9-2
Fantaisie-Impromptu Op.66
Étude Op.10-3 “Chanson de l’adieu”
Étude Op.10-5 “Black Keys”
Étude Op.10-12 “Revolutionary”
Étude Op.25-9 “Butterflies”
Prélude Op.28-7
VIBES/CLAVI
Original
ORGAN
Original
Valse Op.64-1 “Petit Chien”
Valse Op.64-2
STRINGS/SYNTH-PAD
BASS/GUITAR
Nessun Dorma [Turandot]
Original
Moments Musicaux 3
VARIOUS/GM TONES
Original
Impromptu Op.90-2
Marche Militaire 1 (Duet)
Frühlingslied [Lieder Ohne Worte Heft 5]
Fröhlicher Landmann [Album fur die Jugend]
Von fremden Ländern und Menschen
[Kinderszenen]
015
016
015
016
Träumerei [Kinderszenen]
B
001
002
017
018
Tambourin
Menuet BWV Anh.114
[Clavierbüchlein der Anna Magdalena Bach]
003
004
005
019
020
021
Inventio 1 BWV 772
Inventio 8 BWV 779
Inventio 13 BWV 784
Praeludium 1 BWV 846
[Das Wohltemperierte Klavier 1]
006
022
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
Le Coucou
Gavotte
Sonatina Op.36-1 1st Mov.
Sonatine Op.20-1 1st Mov.
Sonate K.545 1st Mov.
Sonate K.331 3rd Mov. “Turkish March”
Rondo K.485
Für Elise
Marcia alla Turca
Sonate Op.13 “Pathétique” 1st Mov.
Sonate Op.13 “Pathétique” 2nd Mov.
Sonate Op.13 “Pathétique” 3rd Mov.
Sonate Op.27-2 “Moonlight” 1st Mov.
Rhapsodie 2
Waltz Op.39-15 (Duet)
C
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
038
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
Liebesträume 3
Blumenlied
La Prière d’une Vierge
Csikos Post
Humoresque Op.101-7
Melodie [Lyrische Stucke Heft 2]
Sicilienne Op.78
Berceuse [Dolly] (Duet)
Arabesque 1
La Fille aux Cheveux de Lin [Préludes]
Passepied [Suite bergamasque]
Gymnopédie 1
Je Te Veux
Salut d’Amour
The Entertainer
Maple Leaf Rag
L’arabesque [25 Etüden Op.100]
La Styrienne [25 Etüden Op.100]
Ave Maria [25 Etüden Op.100]
Le retour [25 Etüden Op.100]
La chevaleresque [25 Etüden Op.100]
No.13 [Études de Mécanisme Op.849]
No.26 [Études de Mécanisme Op.849]
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix/Apéndice
Music Preset List/Lista de preajustes musicales
Group
Name/
Nombre
del grupo
Group
Number/
Númerode
grupo
Sequential
Number/
Número
Group
Name/
Nombre
del grupo
Group
Number/
Númerode
grupo
75
Sequential
Number/
Número
secuencial
Preset Name/
Nombre de preajuste
Preset Name/
Nombre de preajuste
secuencial
A
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
Funky Clavi
POPS
1
76
Earth Disco
70’s Disco
Disco Lady
Staying
1
Soft Pop
77
2
2
Winter Pop
Oldies Pop
Alpine Flora
Gypsy
78
3
3
79
4
4
80
Upside
5
5
81
80’s Disco
Give You Up
Bb Girl
6
6
Rain Pop
Movie Waltz
Blowin’ in
Funky Rspct
Love Pop
Loco
82
7
7
83
8
8
84
Blv Disco
Lady M
9
9
85
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
ROCK
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
DANCE
74
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
86
Out Of My H
Euro Pop
Don’t Funk
Trance
87
Rising Sun
Believer
88
89
Pop Ska
90
The Escape
Weep Blues
Sugar Pop
JoyWorldPop
My Life
JAZZ
91
91
92
Wonderland
My Swing
Things
92
93
93
Ribbon
94
94
Angel
Blue Love
Xmas Pop
Close
95
95
Time
96
96
Leaf
97
97
Blackbird
Dolphin
Roses
Going On
70’s Pop
98
98
99
99
West Coast
Bossa Pop
Radio Pop
Crazy Roll
Ivory Pop
UK Pop
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
Steps
RhythmChange
Swing Mood
The Mood
Brown Jug
Lullaby
Breath You
A Feeling
Calling
Night
Street
Doll
Take On
Someday
Mode Jazz
Train
The World
PlaceOnEarth
Mexican Pop
Guitar Pop
W Up
Tea Time
Jazz Waltz
Home
Sign
Blues in F
Blues in Bb
Blues in C
II-V
Wonder
Hips D Lie
Say Right
MdrnPopRock
II-V-I
Minor Blues
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
Rock Clock
Johnny
B
CLASSIC
1
Heartache
EP R&R
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
Canon
2
Air G String
Je Te Veux
Adagio
Pop R&B
3
60’s Rock 1
60’s Rock 2
60’s Rock 3
60’s Rock 4
60’s Rock 5
Get Rock
Honky Rock
Wild Rock
Alligator
4
5
Spring
6
Ave Maria
JesusBleibet
Symphony 25
Symphony 40
HungriaDance
Eine Kleine
Pathetique
Moonlight
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
The Tiger
Pop Rock
16Bt Rosa
Heat Up
PstlSymphony
Ode To Joy
Le Cygne
Hard Rock
Grunge Rock
Latin Rock
Hanging By
R&R
Swan Lake
Valse Fleurs
Habanera
Nocturne
Etude
Piano R&R
Blues
FrenchCancan
FantaisieImp
Humoresque
Pavane
8 Bars Blues
Riff Rock 1
Riff Rock 2
Riff Rock 3
Hope & Glory
Moldau
FromNewWorld
Reverie
74
Disco Freak
A-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix/Apéndice
Group
Name/
Nombre
del grupo
Group
Number/
Númerode
grupo
30
Sequential
Number/
Número
secuencial
150
Group
Name/
Nombre
del grupo
Group
Number/
Númerode
grupo
7
Sequential
Number/
Número
secuencial
227
Preset Name/
Nombre de preajuste
Preset Name/
Nombre de preajuste
Nutcracker
Xmas Ballad
31
151
Liebestraume
Gymnopedies
Jupiter
8
228
Love Me
32
152
9
229
Oldies Bld 1
Oldies Bld 2
Oldies Bld 3
Oldies Bld 4
E World
33
153
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
JAZZ BALLAD
69
70
71
72
73
74
75
76
77
78
79
80
230
34
154
Entertainer
MapleLeafRag
231
35
155
232
TRAD
36
233
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
Michael Row
GrndpasClock
Troika
234
Tears
37
235
Moon Waltz
A’s Theme
Paradise
38
236
39
AuldLangSyne
Aloha Oe
237
40
238
60’s Ballad1
60’s Ballad2
Whiter Shade
FrenchBallad
Everywhere
Wonderful
70’s Ballad1
70’s Ballad2
My Song
41
O Sole Mio
239
42
Furusato
240
43
SzlaDziweczk
Battle Hymn
Condor
241
44
242
45
243
46
ScarboroFair
Danny Boy
244
47
245
48
Greensleeves
Annie Laurie
AmazingGrace
WeWishU Xmas
Silent Night
Joy To World
YankeeDoodle
Clarnt Polka
TaRaRaBoom
Double Eagle
Blauen Donau
Yellow Rose
BeautDreamer
246
49
247
Bridge
50
248
Img Ballad
Without
51
249
52
250
Not In Love
Soft Ballad
We Were
53
251
54
252
55
253
Minor Ballad
Pop Ballad 1
Pop Ballad 2
PianoBallad1
PianoBallad2
Musical Bld
R Ballad
56
254
57
255
58
256
59
257
60
258
LATIN
61
259
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
Moon Bossa
Your Smile
Rio
260
Always Mind
Endless
62
261
63
262
80’s Ballad1
80’s Ballad2
80’s Ballad3
80’s Ballad4
Friends For
Rock Ballad
Eternal
64
Bossa Blue
One Note
Wave Bossa
Out Of Tune
Quiet Star
Insentive
Brzl Samba
Orpheus
263
65
264
66
265
67
266
68
267
69
268
70
269
Everything
Save Best
Of The Road
I Always
71
270
72
Tico-Tico
Beguine
271
73
272
74
Amapola
La Paloma
Banana Boat
Peanut
273
New World
Vision
75
274
76
275
I Can Fly
77
276
Wind Ballad
Love To You
My Ballad
Beautiful
78
Coffee
277
79
Jamaica
278
80
MoreBeguine
The No.5
Everyday
Mucho
279
81
280
Scrubs
82
281
Falling
83
282
BlngTogether
B Day
84
El Tango
El Choclo
Sheriff
283
85
284
Rap Ballad
Dance Ballad
MdrnRock Bld
Slow Ballad
Kiss Rose
86
285
87
No Woman
Can’t Help
Livin’
286
88
287
89
288
90
Whenever
COUNTRY
91
289
290
291
292
293
294
295
296
297
298
299
300
Summer
New York
B & S
211
212
213
214
215
216
217
218
219
220
This Land
My Sunshine
Walk Line
Home Roads
A Friend
92
93
L Alone
Foggy
94
95
Moon Swing
Foolish
96
Cowboy
97
Still One
Valentine
Midnight
Journey
Star
98
Breath
99
CountryWaltz
He Cheats
100
C
Starlight
BALLAD
1
2
3
4
5
6
221
222
223
224
225
226
Love Ballad
R&B Ballad
Soul Ballad
Blues Ballad
MovieBallad1
MovieBallad2
A-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix/Apéndice
Fingered 3, Full Range Chords/
Acordes Fingered 3, Full Range
Fingering Guide/
Guía de digitación
In addition to the chords that can be fingered with
Fingered 1 and Fingered 2, the following chords also
are recognized.
Fingered 1, Fingered 2 Chords/
Acordes Fingered 1, Fingered 2
Además de los acordes que se pueden digitar con
Fingered 1 y Fingered 2, también se pueden reconocer
los siguientes acordes.
C
#
b
b
#
C
D
C
E
C
F
C
G
C
A
B
B
C
C m Dm ꢀ Fm
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Cm
Cdim
C
C
C
C
C
C
b
b
b
Gm ꢀ Am ꢀ B m ꢀ Ddim ꢀ A 7 ꢀ F7 ꢀ Fm7 ꢀ Gm7 ꢀ A add9
C
C
C
C
C
C
C
C
C
Caug *3
NOTE
Csus4 *3
• With Fingered 3, the lowest note fingered is
interpreted as the base note. Inverted forms are not
supported.
Csus2 *3
C7
• With Full Range Chord, when the lowest fingered is
a certain distance from the neighboring note, the
chord is interpreted as a fraction chord.
• Unlike Fingered 1, 2, and 3, Full Range Chord
requires pressing of at least three keys to form a
chord.
Cm7 *3
CM7
Cm7b5 *3
NOTA
• Con Fingered 3, la nota más baja digitada se
interpreta como nota base. No se pueden usar
formas invertidas.
C7b5 *3
• Con Full Range Chord, cuando la nota digitada más
baja se encuentre a cierta distancia de la nota
adyacente, el acorde se interpreta como un acorde
bitonal.
C7sus4
Cadd9
• A diferencia de Fingered 1, 2, y 3, Full Range Chord
requiere la pulsación de tres teclas como mínimo
para formar un acorde.
Cmadd9
CmM7
Cdim7 *3
C69 *3
C6 *1 *3
Cm6 *2 *3
*1 With Fingered 2, interpreted as Am7.
b
*2 With Fingered 2, interpreted as Am7 5.
*3 Inverted form not supported in some cases.
*1 Con Fingered 2, se interpreta como Am7.
b
*2 Con Fingered 2, se interpreta como Am7 5.
*3 En algunos casos no se puede usar de forma
invertida.
A-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix/Apéndice
Chord Example List/Lista de ejemplos de acordes
A-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Model AP-620/AP-6
Function
Version : 1.0
MIDI Implementation Chart
Transmitted
Recognized
Remarks
Basic
Channel
Default
Changed
1 - 16
1 - 16
1 - 16
1 - 16
Default
Messages
Altered
Mode 3
X
Mode 3
X
Mode
Note
Number
0 - 127
0 - 127
*
True voice
0 - 127 1
** : no relation
** : sin relación
Note ON
Note OFF
O
9nH v = 1 - 127
O
9nH v = 1 - 127
Velocity
**
X
8nH v = 64
X
9nH v = 0, 8nH v =
After
Touch
Key’s
Ch’s
X
X
X
O
Pitch Bender
X
O
Bank select
0, 32
1
O
X
X
X
O
X
X
X
X
X
X
O
X
O
O
X
X
X
X
X
X
X
X
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Modulation
Portamento Time
Data entry LSB, MSB
5
*2
6, 38
7
Volume
Pan
Expression
10
11
*2
DSP Parameter0
16
*2
DSP Parameter1
17
*2
DSP Parameter2
18
*2
DSP Parameter3
19
Damper
64
Portamento Switch
Sostenuto
65
Control
Change
66
Soft pedal
67
Vibrato rate
Vibrato depth
Vibrato delay
76
77
78
*2
DSP Parameter4
80
*2
DSP Parameter5
81
*2
DSP Parameter6
82
*2
DSP Parameter7
83
Portamento Control
Reverb send
84
91
Chorus send
93
*2
RPN LSB, MSB
100, 101
120
121
All sound off
Reset all controller
Program
Change
O
O
O
0 - 127
:True #
*2
System Exclusive
O
System
Common
: Song Pos
: Song Sel
: Tune
X
X
X
X
X
X
System
Real Time
: Clock
: Commands
O
O
X
X
Aux
: Local ON/OFF
: All notes OFF
: Active Sense
: Reset
X
O
X
X
X
O
O
X
Messages
*1 : Depends on tone
Remarks
*1 : depende del tono
Mode 1 : OMNI ON, POLY
Mode 3 : OMNI OFF, POLY
Mode 2 : OMNI ON, MONO
Mode 4 : OMNI OFF, MONO
O :Yes
X : No
B
Download from Www.Somanuals.com. All Manuals Search And Download.
This recycle mark indicates that the packaging conforms to
the environmental protection legislation in Germany.
Esta marca de reciclaje indica que el empaquetado se
ajusta a la legislación de protección ambiental en Alemania.
C
MA1003-B Printed in China
AP620/6ES1A
Download from Www.Somanuals.com. All Manuals Search And Download.
|