Casio Digital Camera QV 770 User Manual

QUICK REFERENCE

To load batteries (page 16)

Be sure to load four AA size batteries that come with this camera before using it.

If you need help with

your camera, please

call: 1(800)435-7732

Slide the battery compartment

lock on the bottom of the camera

(1), and open the battery com-

partment cover (2).

Load four batteries and close the battery compart-

ment cover.

LCD Digital Camera

• Be sure to use Alkaline or Lithium batteries. Never use manganese batteries.

• Press down on the battery compartment cover at the point marked A in the above illustration until the

cover locks into place with a click.

QV-770

CASIO COMPUTER CO.,LTD.

6-2, Hon-machi 1-chome

Shibuya-ku, Tokyo 151-8543, Japan

Owner's Manual

英

QUICK REFERENCE

To Record Images (page 20)

To Playback Images (page 33)

Slide the Function

Switch to REC.

Slide the POWER Switch to the right.

Slide the POWER Switch

to the right to turn on the

camera.

• The image you recorded appears on the LCD.

Use [+] and [–] to scroll

through the images stored

in camera memory.

Set the NORMAL/

MACRO switch to

　　(NORMAL)

position.

Compose the image

on the monitor

screen and then

press the shutter

button.

• Use

(Macro) when

the subject is located

about 15 cm (about 6

inches ) from the lens

(see page 24).

Slide the Function

Switch to PLAY.

Press　　　button to select resolution setting you want.

• Each press of　　　　button cycles through the resolution setting in the

following sequence: 　(Fine)　　(Normal)　　(Economy).

The camera may contain pre-recorded demonstration images

when you purchase it. To delete these images, see page 5.

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

• Should foreign matter or water ever get into the unit, imme-

diately turn power off, unplug the AC adaptor from the

power outlet, and contact your dealer or nearest CASIO

service provider. Using the unit under these conditions cre-

ates the danger of fire and electrical shock.

• Should you ever notice smoke or a strange odor coming

out of the unit, immediately turn power off and unplug the

AC adaptor from the power outlet. Using the unit under

these conditions creates the danger of fire and electrical

shock. After making sure there is no more smoke coming

from the unit, take it to your nearest CASIO service pro-

vider for repair. Never attempt your own maintenance.

• If the unit’s case should ever become cracked due to drop-

ping it or otherwise subjecting it to rough treatment, imme-

diately turn power off, unplug the AC adaptor from the

power outlet, and contact your nearest CASIO service pro-

vider.

• Never use the unit inside of an air craft or in any other ar-

eas where its use is prohibited. Doing so can result in an

accident.

• Physical damage and malfunction of this unit can cause

the image data stored in its memory to be deleted. Be sure

to always keep backup copies of data by transferring them

to personal computer memory.

General Precautions

Be sure to observe the following important precautions

whenever using the QV-770.

Battery Life Notes

Operating conditions

• The battery life figures noted in the specifications of this

Owner’s Manual indicate the number of hours before bat-

tery failure under normal operating temperatures (25°C).

They do not guarantee that batteries will perform for any

amount of time.

• The actual number of hours of service provided by batter-

ies varies widely depending upon manufacturer, battery

age, and temperature.

• Long term continued use of the camera can cause the low

battery indicator to appear sooner than expected. Be sure

to turn off power whenever the camera is not being used.

• Appearance of the low battery indicator means that batter-

ies are about to go dead. Be sure to replace all four batter-

ies a fresh set of new ones as soon as possible. Leaving

dead batteries in the camera creates the danger of leaking

batter fluid and corruption of stored image data.

• This camera is designed for use in temperatures ranging

from 0°C to 40°C (32°F to 104°F).

• Do not use or keep the camera in the following areas.

— In areas subject to direct sunlight

— In areas subject to high humidity or dust

— Near air conditioners, heaters, or other areas subject to

temperature extremes

— Inside of a closed vehicle, especially one parked in the

sun

All references in this manual to “this camera” and “the cam-

era” refer to the CASIO QV-770 Digital Camera.

• Never try to take pictures or use the built-in display while

operating a motor vehicle or while walking. Doing so cre-

ates the danger of serious accident.

• Never try to open the case of the camera or attempt your

own repairs. High-voltage internal components create the

risk of electrical shock when exposed. Always leave main-

tenance and repair work up to authorized CASIO service

providers.

• Never fire the flash in the direction of a person operating a

motor vehicle. Doing so can interfere with the driver’s vi-

sion and create the danger of accident.

• Never fire the flash while it is too close to the subject’s

eyes. Be especially careful with small children. Intense

light from the flash can cause eye damage if it is fired too

close to the eyes, especially with young children. When

using the flash, the camera should be at least one meter

(3.3') from the eyes of the subject.

— In areas subject to strong vibration

Condensation

• When you bring the camera indoors on a cold day or other-

wise expose it to a sudden change of temperature, there is

the possibility that condensation can form on the exterior or

on interior components. Condensation can cause malfunc-

tion of the camera, so you should avoid exposing it to con-

ditions that might cause condensation.

• To keep condensation from forming, place the camera into

a plastic bag before moving it into a location that is much

warmer or colder than your current location. Leave it in the

plastic bag until the air inside the bag has a chance to

reach the same temperature as the new location. If con-

densation does form, remove the batteries from the cam-

era and leave the battery compartment cover open for a

few hours.

• Never open the battery compartment cover, disconnect the

AC adaptor from the camera or unplug it from the wall

socket while the “WAIT” message is on the LCD. Doing so

will not only make storage of the current image impossible,

it can also corrupt other image data already stored in cam-

era memory.

• Keep the camera away from water and other liquids, and

never let it get wet. Moisture creates the danger of fire and

electrical shock. Never use the camera outdoors in the rain

or snow, at the seashore or beach, in the bathroom, etc.

PRECAUTIONS

GUIDELINES LAID DOWN BY FCC RULES FOR USE OF

THIS UNIT IN THE U.S.A. (not applicable to other areas).

About the camera’s backlight…

• The camera is equipped with a fluorescent light source to

provide the back lighting for its LCD.

• The normal service life of the backlight is approximately six

years, when the camera is used for about two hours a day.

• Should the LCD image appear abnormally dark, take the

camera to your dealer or an authorized CASIO service pro-

vider to have the light source replaced. Note that you will

be charged for this replacement.

Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful in-

terference, and (2) this device must accept any interference received, in-

cluding interference that may cause undesired operation.

Model Number:

Trade Name:

Responsible party:

Address:

QV-770

CASIO COMPUTER CO.,LTD.

CASIO INC.

NOTICE

This equipment has been tested and found to comply with the limits for

a Class B peripheral, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interfer-

ence to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

570 MT. PLEASANT AVENUE,

DOVER,NEW JERSEY 07801

•

Under very cold conditions, the backlight may require more

time than normal to light, or reddish bands may appear in

the image. These conditions do not indicate malfunction,

and normal operation should return at higher temperatures.

Telephone number: 973-361-5400

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, in-

cluding interference that may cause undesired operation.

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

CASIO COMPUTER CO.,LTD.

QV-770

Changes or modifications not expressly approved by the party respon-

sible for compliance could void the user's authority to operate the

equipment.

Properly shielded cables with ferrite core must be used for connection

to host computer and/or peripherals in order to meet FCC emission

limits.

Tested To Comply

With FCC Standards

THE SPECIAL VIDEO CABLE THAT COMES WITH THE CAMERA

FOR HOME OR OFFICE USE

----- THE CAMERA TO

THE SPECIAL CONNECTION CABLE THAT COMES WITH QV-Link SOFTWARE

----- THE CAMERA TO PROPER TERMINAL OF COMPUTER

VIDEO IN TERMINAL OF

COMPUTER

Download from Www.Somanuals.com. All Manuals Search And Download.

UNPACKING

GENERAL GUIDE

Check to make sure that all of the items shown below are

included with your camera. If something is missing, contact

your dealer as soon as possible.

The following illustrations show the names of each component, button and switch on the camera.

Connecting the Wrist Strap

Pass the wrist strap through the hole on the side of the cam-

era as shown in the illustration.

Top and Display

Lens

D F

IMPORTANT!

2 4

LCD

Shutter button

VIDEO OUT terminal

AC Power terminal

DIGITAL terminal

Terminal panel cover

FLASH

Infrared port

Exposure sensor

Lens

Be sure to keep the wrist strap around your wrist when-

ever using the camera to protect against accidentally

dropping it.

DISP button

MENU button

[–]

Alkaline batteries

(AA-size × 4)

[+]

Charge lamp

button

MODE button

FUNCTION switch

POWER switch

Camera

switch

6 8

0 A

Using the Soft Case

Wrist Strap

Bottom

Opening the Terminal Panel Cover

Keep the camera in its soft case to protect it when not in use.

Slide the stopper and close the soft case as shown in the

illustration.

Soft case

Stopper

Tripod hole

Battery compartment

cover

Battery compartment

lock

IMPORTANT!

As shown in Figure 1 above, pull the connector cover

out as far as it will go and then lift up to open it. Never

force the cover. Doing so can damage it.

Manual

Video cable

はじめに

MONITOR SCREEN

POWER SUPPLY

• Pressing DISP during recording and playback changes the

information shown on the monitor screen.

• The display area of the image shown on the monitor screen

is slightly smaller than the actual full image.

The camera features a two-way power supply that lets you

use either batteries (AA-size Alkaline or Lithium) or house-

hold AC current.

Playback Mode

Be sure to use Alkaline or Lithium batteries. Never use

manganese batteries (see precautions on the next

page).

Pages

To load batteries

• Press down on the battery compartment cover at the point

marked A in the illustration until the cover locks into place

with a click.

Recording Mode

Be sure that camera power is turned off whenever loading or

replacing batteries.

Protect indicator

Mode

(FINE)

Macro indicator

Flash Mode

Recording Mode

Remaining

(NORMAL)

(ECONOMY)

1. Slide the battery compartment

lock on the bottom of the camera

in the direction indicated by ar-

row (1), and swing open the bat-

tery compartment cover as indi-

cated by arrow (2).

Standard Battery Life

Auto

None

number of page

Flash On

Flash Off

The battery life reference values given below indicate the

amount of time at standard temperature (25°C) until power

automatically turns off due to battery failure. They do not

guarantee that batteries will perform the amount of service

indicated. Battery life is reduced by low temperatures and

continued use.

Mode

(FINE)

Battery capacity

(NORMAL)

(ECONOMY)

Manual recording

indicator

2. Insert four batteries and close the battery com-

partment cover.

Playingback

Movie

Panorama

Playback

Battery capacity EV shift

Type of

Operation

AA-size Alkaline

Batteries LR6

AA-size Lithium

Batteries FR6

About Recocrding Mode

Normal Recording

Continuous

Playback

Approximately 190

minutes

Approximately 320

minutes

Self timer

Recording (Single)

Continuous

Recording

Approximately 690

shots

Approximately 1,430

shots

Self timer

Recording (Movie)

Movie Recording

MOVIE

“Continuous Recording” is made without use of the camera’s

flash.

Serial Recording

(Continuous)

Self timer

Recording (Future)

FUTURE

Regardless of use of the camera’s flash, turning on and off

the POWER Switch, as well as other operating conditions

may affect the above values.

Number of images in panorama

(only when a panorama image

is on the monitor screen)

Serial Recording (Past)

Serial Recording (Future)

Panorama Recording

Title Recording

Download from Www.Somanuals.com. All Manuals Search And Download.

POWER SUPPLY

NOTE

• Always make sure that the positive [+] and

negative [–] ends of the batteries are facing

correctly, as noted by the markings on the

camera itself. Improper loading of batteries can

result in bursting or leaking of batteries, creat-

ing the danger of personal injury or soiling of

objects nearby.

Low Battery Indicator

The battery capacity indicator in the lower left of the monitor

screen (shown only when image information display is

Auto Power Off

Battery life is based on Panasonic’s alkaline batteries

and Fujifilm’s lithium batteries.

They may vary if other manufacturer’s batteries are

used. For your reference, the values when the camera

is operated with Duracell’s batteries are shown below.

Power automatically turns off whenever you do not perform

any camera operation for a period of time. Power turns off

after about two minutes in the Record Mode or after about

five minutes in the Playback Mode.

• To restore power, simply slide the POWER Switch to the

right as you normally do.

turned on) changes to “

low. If you continue to use the camera, a battery warning

indicator “ ” will appear in the center of the monitor

” whenever battery power goes

CAUTION

screen, and then camera power will automatically turn off. If

this happens, replace all four batteries with new ones as

soon as possible.

Type of Operation

Auto Play

AA-size alkaline batteries LR6

Approximately 100 minutes

Approximately 190 shots

• Remove batteries from the camera if you do not plan to use

it for more than two weeks.

• Never recharge batteries, never allow direct connection

between two ends of a battery, and never try to take batter-

ies apart.

• Do not expose batteries to direct heat or dispose of them

by burning. Doing so can create the danger of explosion.

• Never mix batteries of different types.

• Dead batteries are susceptible to leakage, which can

cause serious damage to your camera. Remove batteries

from the camera as soon as you notice they are dead.

• The batteries that power this camera normally become

warm when they lose power. This does not indicate mal-

function.

POWER

ON/OFF

Note that the camera may automatically shut down at a

somewhat higher level of remaining battery capacity when a

computer is connected to its DIGITAL terminal for data com-

munication. This is to protect against problems caused by

sudden power outage during data communications. Be-

cause of this, we strongly recommend that you use the op-

tionally available AC adaptor to power the camera whenever

performing data communication with a personal computer.

Continuous Recording

Battery Handling Precautions

Incorrect use or handling of batteries can cause them to leak

or burst and seriously damage your camera. Be sure to note

the following important precautions to avoid problems with

batteries.

IMPORTANT!

The Auto Power Off function does not operate under the

following conditions.

• Use only LR6 (AM-3) type alkaline or FR6 type

lithium dry cell batteries with this camera.

Never mix old batteries with new ones. Failure

to do so can result in bursting or leaking of bat-

teries, creating the danger of fire or personal

• During playback of a movie (page 34)

• During playback of a panorama (page 35)

• During Auto Play (page 39)

• During infrared communication (page 65)

• When operations are being performed on a computer

connected to the camera via the camera’s DIGITAL

terminal. (page 59)

CAUTION

injury.

• Whenever the AC adaptor is connected to the camera.

RECORDING

POWER SUPPLY

RECORDING

• Always be sure to use the AD-C620 AC adap-

tor only. Using any other AC adaptor can cause

damage to the camera not covered by the war-

ranty.

3. Set the NORMAL/MACRO

Using AC Power

Basic Recording Operation

switch to

position.

(NORMAL)

To power the camera from standard AC power, use the op-

tional AC adaptor (AD-C620).

The following describes the basic operation for recording

images.

• When unplugging the AC adaptor from the wall

socket, be sure to grasp the adaptor (not the

cord).

AC power

terminal

1. Slide the Function

Switch to REC.

•

Use

when the subject is located about 15 cm from

AC adaptor

CAUTION

REC

the lens (about 6 inches). See page 24 for details on

using this switch.

• Avoid an undue bending, pulling, and twisting

of the AC adaptor’s cord, and never try to

lengthen the cord by splicing it with other wire.

PLAY

4. Press

resolution setting you

want.

to select

/Tran-P

MODE

•

The REC position selects the Record Mode, while

PLAY selects the Playback Mode.

AC outlet

• Be sure to switch power off before connecting or discon-

necting the adaptor.

•

Each press of

setting in the following sequence: (Fine)

mal) (Economy).

cycles through the resolution

2. Slide the POWER Switch

in the direction indicated

by the arrow.

• Always turn camera power off before disconnecting the AC

adaptor, even if the camera has batteries installed. If you

don’t, the camera will turn off automatically when you dis-

connect the AC adaptor. Even so, you run the risk of dam-

aging the camera whenever you disconnect the AC adap-

tor without first turning power off.

• The AC adaptor may become warm to the touch after ex-

tended periods of use. This is normal and is not cause for

alarm.

POWER

ON/OFF

(Nor-

AC Adaptor precautions

The resolution setting you select here affects how

many images can be stored in memory. See “Resolu-

tion Settings” on page 24 for details.

• Never use an electrical outlet whose voltage is

outside the rating marked on the AC adaptor.

Doing so can create the danger of fire or elec-

trical shock. Use only the optional AC adaptor

specified for this camera.

•

The POWER Switch returns to its original position

when you release it.

5. Compose the image on

the monitor screen and

then press the shutter

button.

•

Turning on power enters the normal Recording Mode.

The monitor screen shows the image picked up by the

lens.

• Should the cord of the AC adaptor become

CAUTION

• After use turn off the power switch of the camera and un-

plug adaptor from the AC outlet.

damaged (exposed internal wiring or shorts),

request a replacement from an authorized

CASIO service provider. A damaged AC adap-

tor cord creates the danger of fire or electrical

shock.

•

You can perform step 2 before step 1, if you want.

If power turns off, slide the POWER Switch again to

turn it back on.

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

•

Viewing the subject on the monitor screen, carefully

compose it within the frames provided on the screen.

IMPORTANT!

Shooting Images Outdoors

Using the Flash

• Never use the flash on areas where combustible or

explosive gas is present. Doing so creates the danger

of fire and explosion.

Note that strong direct or reflected light can cause vertical

lines in an image. This is due to the characteristics of the

camera’s charge-coupled device (CCD), and it does not indi-

cate malfunction of the camera.

You can use the built-in flash unit to provide illumination dur-

ing recording. Auto Flash causes the flash to fire automati-

cally whenever the shutter button is pressed while available

light is below a certain level.

•

Take care to avoid blocking the lens with your fingers.

Carefully press the shutter button, taking care not to

move the camera as you do.

• Never fire the flash in the direction of a person operat-

ing a motor vehicle. Doing so can interfere with the

driver’s vision and create the danger of accident.

• Never fire the flash while it is too close to the subject’s

eyes. Be especially careful with small children. In-

tense light from the flash can cause eye damage if it is

fired too close to the eyes, especially with young chil-

dren. When using the flash, the camera should be at

least one meter (3.3') from the eyes of the subject.

• Make sure that you do not touch or block the flash or

exposure sensor with your fingers. Doing so can soil

these components and interfere with correct flash op-

eration.

•

You can view images immediately after you record

them by sliding the Function Switch to the PLAY.

1. Press

to select the flash mode.

Each press of cycles through the flash

modes in the following sequence: Auto Flash Flash

On “ ” Flash Off “ ”.

•

CAUTION

• Never open the battery compartment cover, discon-

nect the AC adaptor from the camera or unplug it from

the wall socket while the “WAIT” message is on the

LCD. Doing so will not only make storage of the cur-

rent image impossible, it can also corrupt other image

data already stored in camera memory.

Indicator

None

Flash Mode

Auto Flash

Description

Flash is automatically enabled and

disabled in accordance with expo-

sure conditions.

• Flash should be used for distances within the range of

about 0.7 meters to 3 meters (2.3' to 9.8'). Flash does

not work well outside this range.

• Depending on operating conditions (type of battery

being used, temperature, etc.), it may take up to 10

seconds for the flash unit to charge.

• Fluorescent lighting actually flickers at a frequency

that cannot be detected by the human eye. When us-

ing the camera indoors under such lighting, you may

experience some brightness or color problems with

recorded images.

Flash On

Flash Off

Flash is always fired, regardless of

exposure conditions.

Flash is never fired, regardless of

exposure conditions.

• The flash does not fire in the following modes: Serial,

• The image on the monitor screen is cleared and the

Charge Lamp flashes while the flash unit is charging.

Movie, Self-timer (movie or future). The

flashes to indicate this condition.

indicator

NOTE

This camera is equipped with “flash memory” that re-

tains images even when batteries go dead and the AC

adaptor is not connected. Images can be recalled after

new batteries are loaded or the AC adaptor is con-

nected.

• The flash unit will not charge when battery power is

low. The indicator flashes red to warn you that the

flash will not fire correctly, which may affect exposure

of the image. Replace batteries as soon as possible

when this happens.

CHARGE

/Tran-P

MODE

Charge lamp

RECORDING

• Any images recorded while the lens body is rotated so the

lens is pointed from the back of the camera are stored as

mirror images of the image that appears in the LCD before

the shutter button is pressed.

Changing the Lens Orientation

NORMAL/MACRO Switch

Resolution Settings

The lens of the camera is built into a lens body that is de-

signed to rotate. This means you can change the angle of

the lens without moving the rest of the camera.

The NORMAL/MACRO switch tells the

camera how much distance there will

be between the lens and the object

whose image you are recording. The

following table describes the condi-

tions covered by each switch setting.

is shown on the monitor screen

whenever the macro position is in use.

Pressing

tings. Each press of

cycles through the available resolution set-

cycles through the resolution

setting in the following sequence: (Fine)

(Economy).

(Normal)

CHARGE

/Tran-P

MODE

(NORMAL)

(MACRO)

Focus Range

0.7m ~ ∞

(2.3' ~ ∞)

14cm ~ 16cm

(5.5" ~ 6.3")

A .... LCD when shutter button is

pressed (in the Record

Mode)

B .... LCD when image is played

back from camera memory

Setting

Indicator

Rotates up to 90°

towards the front

Rotates up to 180°

towards the back

Resolution

Number of Images

The above figures indicate the distance from the lens protec-

tion filter to the subject.

Fine

30 (minimum)

(approx. 124KB compressed image)

Normal

60 (minimum)

(approx. 62KB compressed image)

IMPORTANT!

Economy

120

• Do not apply excessive force when rotating the lens

body. Doing so can cause serious damage to the lens.

• Do not carry the camera or move it around while hold-

ing onto only the lens body.

• Return the lens body to its normal position (with the

lens pointing from the front of the camera) before stor-

ing the camera.

(approx. 32KB compressed image)

• The above figures are approximations only. The actual

number of images depends on image subject matter.

• Up to 120 images (total of

images)

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

NOTES

Exposure Adjustment

【＋】

【－】

• Exposure adjustment is generally expressed in terms

of an exposure adjustment value. The exposure ad-

justment value is always set to zero whenever you

turn on the camera.

• The exposure adjustment value is changed by 0.25EV

with each press of [+] or [–]. The range of the value is

–2EV to +2EV.

This camera features an program AE function that automati-

cally changes shutter speed and aperture in accordance

with available light. In addition, you can also manually adjust

the exposure to compensate for backlighting, indirect indoor

lighting, dark backgrounds, and other special conditions.

• The exposure adjustment value automatically reverts

to zero whenever the shutter button is pressed. You

can manually reset the exposure adjustment value by

using [+] and [–] to change the value back to zero,

which is indicated when the bar graph disappears from

the monitor. EV shift is fixed during panorama record-

ing.

To manually adjust the exposure

1. Set the Function Switch to REC.

3. After adjusting the exposure, press the shutter

button to record the image.

2. Use [+] and [–] to perform exposure compensa-

tion and display a bar graph on the monitor

screen.

• Shutter speed and aperture is fixed whenever an EV

shift setting is made.

•

Pressing [+] makes the image on the LCD brighter.

Use it to adjust for dim indoor lighting and backlight-

ing.

IMPORTANT!

•

Pressing [–] makes the image on the LCD darker. Use

it to adjust for bright sunlight.

• When the exposure adjustment is too bright or too

dark, you may not be able to adjust within the range of

–2EV to +2EV.

• The aperture setting of this camera switches auto-

matically in accordance with available lighting when

an image is recorded. The switching operation causes

the camera to emit a noise. This is normal and does

not indicate malfunction.

The bar graph turns red whenever the compensation

value is at its limit.

OTHER RECORDING FUNCTIONS

Serial Recording

This section describes more advanced recording operations

that are also provided by this camera.

•

Storage of the 32 frames in memory uses up two still

images worth (two pages) of memory.

1. Slide the Function Switch to REC.

There are three different serial recording modes: continu-

ous, past, and future.

Serial Recording Mode

2. Press MODE a number of

times until the screen

shown on the right hand

appears, which indicates

the Serial Recording

Mode.

•

See “Playingback Movie” on page 34 for details on

playingback movie.

Movie Recording

• Continuous (CONT.S)

You can record a movie up to 3.2 seconds long.

IMPORTANT!

With this mode, image recording continues as long as the

shutter button is depressed. Images are recording at inter-

vals of about one second.

• Flash is disabled during movie recording.

• All the images that make up a movie are treated as a

single unit for image movement, delete, and protect

operations.

• Movie images that are uploaded to a personal com-

puter and then downloaded back to the camera can-

not be played back as a movie.

1. Slide the Function Switch to REC.

• Past (PAST)

Movie Recording Mode

This mode records the image in front of the lens the instant

the shutter button is pressed, along with three images 0.05,

0.1 and 0.15 seconds before the shutter button is pressed.

• Future (FUTURE)

2. Press MODE a number of

times until the screen

shown on the right hand

appears, which indicates

the Movie Recording

Mode.

3. Press MENU.

This mode records the image in front of the lens the instant

the shutter button is pressed, along with four subsequent

images at intervals of about 0.05 second.

• The resolution of movie images is always (Fine), and

cannot be converted.

• Memory enough to store at least two (Fine) images

must be free in order to record a movie.

SHUTTER

4. Use [+] and [–] to select the Serial Recording

Mode you want to use, and then press the shut-

ter button.

3. Compose the image on the monitor screen and

then press the shutter button.

Time Recording (Past)

Time Recording (Future)

1 2 3 4

•

The movie icon flashes as 32 frames are recorded at

intervals of approximately 0.1 second.

5. Compose the image on the monitor screen and

then press the shutter button to start the

record operation.

IMPORTANT!

• The flash unit is disabled during serial recording.

• The number of images actually recorded in the PAST

mode and FUTURE mode depend on the amount of

memory available.

•

If you are using the CONT.S mode, keep the shutter

button depressed until you record everything you

want.

Download from Www.Somanuals.com. All Manuals Search And Download.

OTHER RECORDING FUNCTIONS

Self-timer

Recording Mode

2. Press MODE a number of

5. Compose the image on the monitor screen and

then press the shutter button to start the

record operation.

Self-timer Recording

Panorama Recording

times until the screen

shown on the right hand

appears, which indicates

the Self-timer Recording

Mode.

There are three different Self-timer Recording Modes:

single, movie, and future.

With panorama recording you record a series of images and

then link them to create a single panoramic effect.

•

A 10-second countdown starts on the LCD. The shut-

ter will release automatically when the end of the

countdown is reached.

• Single (SINGLE)

After about 10 seconds have elapsed, this mode records a

single image.

•

To cancel ongoing Self-Timer operation, press shutter

button.

• Movie (MOVIE)

Starts movie recording 10 seconds after the shutter button

is pressed. See “Movie Recording” on page 27 for details

on movie recording.

NOTE

3. Press MENU.

During self-timer recording, you may find it helpful to

rotate the swivel lens mechanism 180 degrees so the

monitor screen faces the same direction as the lens.

This way you can always see how much time is left until

the start time is reached and recording begins.

• Future (FUTURE)

1. Slide the Function Switch to REC.

After about 10 seconds have elapsed, this mode records

the image in front of the lens the instant the shutter button

is pressed, along with four subsequent images.

Panorama

Recording Mode

2. Press MODE a number of

times until the screen

IMPORTANT!

The flash fires only when SINGLE is selected.

shown on the right hand

appears, which indicates

the Panorama Recording

Mode.

4. Use [+] and [–] to select the Self-timer Record-

ing Mode you want to use, and then press the

shutter button.

1. Slide the Function Switch to REC.

OTHER RECORDING FUNCTIONS

Manual Recording

OTHER RECORDING FUNCTIONS

3. Compose the image on the monitor screen and

then press the shutter button to record.

1. Slide the Function Switch to REC.

5. Use [+] and [–] to select the white balance (WB)

setting you want to use, and then press the

shutter button.

With this operation you manually set the aperture and white

balance to the settings you want to use in order to produce

special effects or to compensate for special conditions.

• You can override automatic settings and manually set ex-

posure and white balance to create exactly the effects you

want for your images.

Manual Recording Mode

2. Press MODE a number of

•

The left edge of the previous image you recorded re-

mains on the monitor screen, so you can use it to com-

pose the next image correctly.

times until the screen

shown on the right hand

appears, which indicates

the Manual Recording

Mode.

•

The

indicator is in the upper left corner of the dis-

play screen.

Up to nine images can be grouped into a panorama.

Press MENU when you want to stop a panorama re-

cording operation.

•

Manual settings you make remain in effect until you

turn off power or change to another mode.

6. Compose the image on the monitor screen and

then press the shutter button to record.

If you want to link more than 9 images into a pan-

orama, upload the images to a computer and use your

computer application to link them.

Aperture

You can select AUTO, F2, or F8 as the aperture setting. F8

allows recording of a wider area (NORMAL Mode: 0.3m ~ ∞

(11.8" ~ ∞), MACRO Mode: 11 ~ 26cm (4.3" ~ 10.2")).

•

The image is recorded using the aperture and white

balance settings you made above.

3. Press MENU.

Aperture and white balance settings are locked when

you record the first image of a panorama, and these

settings are applied to all subsequent images in that

panorama.

•

To return the aperture and white balance settings to

their default (AUTO) settings, turn off the camera or

select normal recording again and set the aperture

(APT) and white balance (WB) both to AUTO.

White Balance

This settings lets you adjust white areas to produce a more

natural-looking image.

•

See “Panorama Playback” on page 35 for details on

playing back panoramas.

Panorama images that are uploaded to a personal

computer and then downloaded back to the camera

cannot be played back using panorama playback.

WB1 .... Use this setting when indoor lighting is making

4. Use [+] and [–] to select

the aperture (APT) set-

ting you want to use, and

then press the shutter

button.

WB1

the image appear reddish.

WB2 .... Use this setting when indoor lighting is making

WB2

the image appear bluish.

WB3 .... Use this setting for outdoor recording.

WB3

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK

The following describes the different techniques that you can

use to playback recorded images.

•

Press the shutter button to return to a previous display

from a mirror display or full screen display. If the previ-

ous display does not appear right away, keep the

shutter button depressed until it does.

【＋】

【－】

【＋】

【－】

Playingback Movie

Use the following operation to play back a movie that was

recorded using the operation under “Movie Recording” on

page 27.

Basic Playback Operation

4. After playingback movie is complete, press the

shutter button again.

NOTE

The built-in monitor screen of the camera lets you play back

recorded images without connecting an external monitor.

Sliding the Function Switch to PLAY immediately after

recording an image displays the image you just re-

corded first.

1. Slide the Function Switch to PLAY.

•

If you playback a movie using the basic (non-movie)

playback operation, only the first frame of the memory

page that contains the first 16 frames of the movie

appears on the screen.

1. Slide the Function

Switch to PLAY.

2. Use [+] and [–] to select

the movie you want to

playback.

REC

•

If one of the memory pages that contains 16 movie

frames has been deleted by the PC Link software ap-

plication, movie will be shortened by half.

PLAY

•

The PLAY position selects the Playback Mode, while

REC selects the Record Mode.

When a movie page (of 16 frames) is sent to or re-

ceived from a personal computer, the applicable

frames play on the monitor screen of the camera.

3. Press the shutter button to start playingback

movie.

2. Use [+] and [–] to scroll through the images

stored in camera memory.

Uploading a movie image to a computer causes it to

be converted automatically to two images, each of

which contains 16 frames.

•

You can use [+] (forward) and [–] (reverse) during

playingback movie to change the playback direction.

•

Press [+] to scroll forward and [–] to scroll back. Hold-

ing down either button scrolls at high speed.

•

Pressing MENU during playingback movie changes to

the menu screen. While the menu screen is on the

monitor, you can use [+] (forward) and [–](reverse)

move frame-by-frame through the movie, or you can

press DISP to change to mirror display and full screen

display.

Auto Power Off is disabled while playingback movie is

in progress.

Pressing the shutter button and the [–] button at the

same time jumps to the first image.

Pressing the shutter button and [+] button at the same

time jumps to the last image.

You cannot perform a jump to the first or last image in

memory during playback of a movie or panorama.

PLAYBACK

4. Press the shutter button to stop panorama

playback.

4. Use [+] and [–] to select

VIEW, and then press the

shutter button.

Panorama Playback

Using Zoom

Use the following operation to playback panoramas re-

corded using the operation under “Panorama Recording” on

page 30.

The following operation lets you magnify an image to twice

its normal size. Note that you can zoom in only on a single

still image.

NOTE

The Auto Power Off function is disabled while pan-

orama playback is being performed.

IMPORTANT!

1. Slide the Function Switch to PLAY.

Movie and panorama images cannot be zoomed.

5. Use [+] and [–] to select ZOOM, and then press

the shutter button.

2. Use [+] and [–] to select

the panorama you want

to playback.

•

This magnifies the center part of the image to twice its

normal size.

6. Use [+] and [–] to slide the image so you can

view the part of it that you want.

3. Press the shutter button

to start panorama play-

back.

7. After you are finished, press any button be-

sides [+], [–], or DISP return the image to its

normal size.

1. Slide the Function Switch to PLAY.

2. Use [+] and [–] to select the image you want to

zoom in.

•

You can use [+] (forward)

and [–] (reverse) during

panorama playback to

change the playback direc-

tion.

3. Press MENU.

•

Press MENU during pan-

orama playback to advance

to the next frame (or previ-

ous frame in the case of re-

verse playback).

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK

3. Use [+] and [–] to select

VIEW, and then press the

shutter button.

Enlarged Image Movement

Selecting a Specific Image

Use the following operation to select one of the images on a

multi-image screen and change to the display of that image

only.

Displaying Multiple Images

The following operation lets you simultaneously view either

four or nine images on the same screen. This capability is

especially useful when playing back to the screen of a con-

nected TV, and can be used to display a catalog of products,

etc.

• When a panorama or movie is included in a multi-page dis-

play, only the first image that makes up the panorama or

movie is shown.

【＋】

1. Use the operation on page 37 to display the

multi-image screen that contains the image

you want.

4. Use [+] and [–] to select 4PAGE or 9PAGE, and

then press the shutter button.

• A movie image appears smaller in size than a normal (non-

movie) image.

•

The first image of the set is the image that was on the

screen when you performed step 2 of this operation.

The other images are those that sequentially follow

the first one.

2. Press DISP.

•

This displays the image

number on the upper left

image.

• Pressing [–] slides the image in the opposite direction.

5. Use [+] and [–] to scroll through images stored

in memory.

NOTE

3. Use [+] and [–] to move the page (image) num-

ber display from image-to -image on the moni-

tor screen.

When an image is enlarged while image information is

【＋】

turned on (page 15), an image part indicator

ap-

1. Slide the Function Switch to PLAY.

2. Press MENU.

pears in the upper right corner to indicate which part of

the image is currently on the screen. Display of the im-

age part indicator can be toggled on and off during the

enlarged display by pressing DISP.

【－】

4. Press the shutter button

to display the image

whose page (image)

number is shown.

6. After you are finished, press any button be-

sides [+], [–], or DISP return to the normal

single-image display.

PLAYBACK

2. Press MENU.

Setting the Auto Play Interval

Auto Play

Screen Saver

You can use the following operation to set the amount of

time that should be allowed between each image during

Auto Play (the Auto Play interval).

Auto Play automatically scrolls through the images stored in

memory. You can also specify how much time should be al-

lowed between each image.

The screen saver function automatically activates Auto Play

(which automatically scrolls through images) whenever you

do not perform any operation for about five minutes in the

Playback Mode. This protects the camera’s monitor screen

and the screen of a connected TV against “burn in” of a static

image that is left displayed too long.

1. Start Auto Play using the operation under “To

start Auto Play” on page 39.

3. Use [+] and [–] to select

VIEW, and then press the

shutter button.

IMPORTANT!

2. Press MENU.

• The screen saver is enabled only when the camera is

being powered by its optional AC adaptor. If you do

not perform any operation for five minutes under bat-

tery power, camera power automatically turns off

(Auto Power Off).

•

Be sure to wait for the im-

age on the screen to stop

before performing any but-

ton operation.

IMPORTANT!

Auto Power Off (page 18) is disabled whenever the

Auto Play is being used. This means you should not

leave Auto Play running when using batteries to power

the camera. Doing so will cause batteries to go dead.

Be sure to stop Auto Play and turn off the camera after

you are finished.

• The screen saver is disabled (it does not activate) if

there are no images stored in memory.

4. Use [+] and [–] to select AUTO PLAY, and then

press the shutter button.

3. Use [+] and [–] to set the Auto Play interval

value you want and then press the shutter but-

ton.

• PC Link will not send images between the camera and

a personal computer while the screen saver is turned

on. Make sure you turn off the screen saver before

trying to perform any image transfer operation. Note

that the screen saver is turned on when you purchase

the camera.

5. To stop Auto Play, press any button besides

MENU.

To start Auto Play

•

You can set the Auto Play interval to any value in the

range of 1 to 30 (seconds).

•

Note that all buttons are disabled while an image

change is in progress. Wait until an image is stopped

on the screen before performing a button operation, or

hold down the button until the image stops.

1. Slide the Function Switch to PLAY.

•

After you make the above setting, Auto Play resumes

using the interval you set.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDITING IMAGES

PLAYBACK

EDITING IMAGES

A selection of powerful built-in editing tools helps you to cre-

ate the effects you want.

5. Use [+] and [–] to select ON, and then press the

shutter button.

1. Slide the Function Switch to PLAY.

To turn the screen saver on and off

2. Use [+] and [–] to display the image to which

you want to apply the filter.

•

To turn off the screen saver, perform the above proce-

dure and select OFF in step 5.

1. Slide the Function Switch to PLAY.

2. Press MENU.

Using Image Filters

•

The screen saver activates if you do not perform any

operation for about five minutes in the Playback

Mode.

3. Press MENU.

Use the following operation to apply black-and-white, sepia,

or another filter to an image. Filters alter the appearance of

an image and create interesting effects.

•

To stop an ongoing screen saver operation, press the

shutter button.

IMPORTANT!

When changing between images, the screen saver

uses the interval that is specified for Auto Play (page

40). To change the interval, press MENU while a

screen saver operation is in progress, and then

specify the interval time you want.

A filter cannot be applied when any of the following con-

ditions are present.

• When an (Fine) resolution image is on the monitor

screen and there is only enough memory remaining to

allow recording of an (Normal) or (Economy) reso-

lution image

3. Use [+] and [–] to select

VIEW, and then press the

shutter button.

4. Use [+] and [–] to select

EFFECT, and then press

the shutter button.

• When an (Normal) resolution image is on the moni-

tor screen and there is only enough memory remain-

ing to allow recording of an (Economy) resolution im-

age

• While a movie image or panorama image is on the

monitor screen

5. Use [+] and [–] to select

FILTER, and then press

the shutter button.

4. Use [+] and [–] to select SCREEN SAVER, and

then press the shutter button.

• When the “MEMORY FULL” message is on the moni-

tor screen

• Applying a filter to a rotated image, automatically

causes the image to return to its normal (unrotated)

orientation.

EDITING IMAGES

Title Recording Mode

6. Use [+] and [–] to select the type of filter you

want, and then press the shutter button to

store the filtered image.

2. Press MODE a number of

Superimposing a Title onto an Image

Adding a Title to an Image

times until the screen

shown on the right hand

appears, which indicates

the Title Record Mode.

Adding a title to an image is actually a two-step process.

First you record the title into title memory, and then you su-

perimpose the title onto the image. Because of this, you

should prepare the title by printing it out on your computer or

handwriting it on a sheet of paper.

IMPORTANT!

Text cannot be added to an images when any of the

following conditions are present.

• When an (Fine) resolution image is on the monitor

screen and there is only enough memory remaining to

allow recording of an (Normal) or (Economy) reso-

lution image

• When an (Normal) resolution image is on the moni-

tor screen and there is only enough memory remain-

ing to allow recording of an (Economy)resolution im-

age

• While a movie image or panorama image is on the

monitor screen

• When the “MEMORY FULL” message is on the moni-

tor screen

• Adding a title to a rotated image, automatically causes

the image to return to its normal (unrotated) orienta-

tion.

•

Each press of [+] and [–] cycles through one of the five

available filters.

•

Applying a filter does not affect the original image. In-

stead, the filtered version is saved as a new image

immediately after the original image. All images fol-

lowing the original image are automatically shifted to

make room.

3. On the monitor screen, compose the title that

you prepared.

MATTERHORN

•

When recording a title, make sure that the title is be-

tween the lines provided.

•

The amount of time it takes the camera to apply a filter

depends on the composition of the original image and

the type of filter you select.

•

You can use [+] and [–] to adjust the exposure of the

title image. See “Exposure Adjustment” on page 25 for

details.

Recording the Title

4. Press the shutter button.

IMPORTANT!

There is space for only one title in title memory. Any title

already in memory is automatically deleted whenever

you record a new title.

1. Slide the Function Switch to PLAY.

1. Slide the Function Switch to REC.

2. Use [+] and [–] to display the image onto which

you want to superimpose the title.

5. Use [+] and [–] to adjust the brightness of the

title image (±30), and then press the shutter

button.

•

The brightness adjustment you make here is stored

along with the title image data.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDITING IMAGES

6. Use [+] and [–] to select

the color you want the

title to be, and then

press the shutter button.

3. Press MENU.

8. Use [+] and [–] to select

the color you want the

plate to be, and then

press the shutter button.

Combining Two Images

The following operation describes how to combine two re-

corded image into a new image.

•

Each press of [+] or [–]

scrolls through the selec-

tion of 20 available title col-

ors.

•

Each press of [+] or [–]

scrolls through the selec-

tion of 12 available plate

colors.

4. Use [+] and [–] to select

EFFECT, and then press

the shutter button.

7. Use [+] and [–] to select

the type of title plate you

want to use, and then

press the shutter button.

9. Use [+] and [–] to select the position of the title

on the image, and then press the shutter but-

ton.

IMPORTANT!

• The following operation cannot be performed unless

there is enough room in memory to store one fine

resolution image.

• You cannot use this operation with a movie, a pan-

orama, or an image that has been rotated.

• Combining a rotated image with another image auto-

matically returns the rotated image to its normal orien-

tation (unrotated).

•

Each press of [+] or [–] changes to one of 5 available

title locations.

•

Each press of [+] or [–]

scrolls through the selec-

tion of 9 available title plate

settings.

5. Use [+] and [–] to select

TITLE, and then press

the shutter button.

•

Pressing the shutter button to register the title location

superimposes the title onto the image and stores the

result immediately after the original image. All images

following the original image are automatically shifted

to make room.

•

Title plate settings consist

of 8 plate variations, plus a

setting that specifies no title

plate.

1. Slide the Function Switch to PLAY.

2. Use [+] and [–] to display the image you want to

use as the foreground image.

EDITING IMAGES

3. Press MENU.

7. Use [+] (left) and [–] (right) to specify the hori-

zontal location of the cutout pattern and then

press the shutter button.

4. Use [+] and [–] to select

MOVE, and then press

the shutter button.

Moving an Image

Use the following operation when you want to move an im-

age to a different location in the sequence of images stored

in memory.

8. Use [+] (up) and [–] (down) to specify the verti-

cal location of the cutout pattern and then

press the shutter button.

1. Slide the Function Switch to PLAY.

2. Press MENU.

4. Use [+] and [–] to select

EFFECT, and then press

the shutter button.

5. Use [+] and [–] to select

the image you want to

move, and then press the

shutter button.

9. Use [+] and [–] to select the image you want to

use as the background image, and then press

the shutter button.

10. If you selected the vertical ellipse or small

circle as the cutout pattern, use [+] and [–] to

select the paste location, and then press the

shutter button.

5. Use [+] and [–] to select

MIX, and then press the

shutter button.

3. Use [+] and [–] to select

TOOL, and then press

the shutter button.

•

Pressing the shutter button combines the two images

according to your specifications and stores the result

immediately after the original foreground image. All

images following the original foreground image are

automatically shifted to make room.

6. Use [+] and [–] to select the type of cut out pat-

tern you want to use, and then press the shut-

ter button.

•

Each press of [+] or [–] scrolls through the selection of

4 available cutout patterns.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDITING IMAGES

6. Use [+] and [–] to select the image that you

want come after the image you are moving, and

then press the shutter button.

4. Use [+] and [–] to select

TOOL, and then press

the shutter button.

7. If you selected 90° or 270° in the previous step,

Rotating an Image

press MENU to specify the background color.

The following operation rotates an image.

•

Skip this step if you specified 0° or 180° in step 6.

Each press of MENU scrolls through the 10 available

background colors.

•

Pressing the shutter button moves the image to the

location above the image you specified in step 6

above. Images after the location you move to are

shifted to make room.

8. Press the shutter button to rotate the image.

•

When you move a movie or panorama, all related im-

ages are moved as a group.

5. Use [+] and [–] to select

ROTATE, and then press

the shutter button.

IMPORTANT!

To jump to the last page

(image) in memory, use [+]

and [–] to display the mes-

sage “LAST PAGE” and

then press the shutter but-

ton.

The above operation only rotates the displayed repre-

sentation of the image, without actually rotating the im-

age itself. This means that uploading the image to a

computer or outputting it to a QV Color Printer sends

the original un-rotated image.

IMPORTANT!

You cannot use the following operation with a movie, or

a panorama.

6. Use [+] and [–] to specify

0°, 90°, 180°, or 270° as

the rotation.

1. Slide the Function Switch to PLAY.

2. Use [+] and [–] to display the image you want to

rotate.

3. Press MENU.

IMAGE PROTECTION

Use the following operations when you want to protect im-

ages against accidental deletion. A protected image cannot

be deleted until it is unprotected. You can protect and

unprotect a single specific image, or all images currently in

memory.

4. Use [+] and [–] to select

PROTECT, and then

press the shutter button.

8. If you want to protect or unprotect other im-

ages, repeat steps 6 and 7.

Protecting and Unprotecting All Images in

Memory

•

When you protect or unprotect a movie or panorama,

all related images are treated as a group.

1. Slide the Function Switch to PLAY.

2. Press MENU.

•

To exit the image protect operation, press MENU. The

image protect operation is also cancelled automati-

cally if you do not perform any button operation for

about one minute.

Protecting and Unprotecting a Single Image

5. Use [+] and [–] to select

PAGE, and then press

the shutter button.

1. Slide the Function Switch to PLAY.

2. Press MENU.

3. Use [+] and [–] to select

TOOL, and then press

the shutter button.

6. Use [+] and [–] to select the image you want to

protect or unprotect.

7. Press the shutter button to toggle image pro-

tection on and off.

3. Use [+] and [–] to select

TOOL, and then press

the shutter button.

4. Use [+] and [–] to select

PROTECT, and then

press the shutter button.

•

The

indicator in the upper left corner of an image

indicates that it is protected.

Download from Www.Somanuals.com. All Manuals Search And Download.

DELETING IMAGES

IMAGE PROTECTION

Use the following operations when you want to delete im-

ages from memory. You can delete a single specific image,

or all images currently in memory.

5. Use [+] and [–] to select “ALL”, and then press

the shutter button.

3. Use [+] and [–] to select

DELETE, and then press

the shutter button.

6. Use [+] and [–] to select ALL (protect) or CAN-

CEL (unprotect), and then press the shutter

button.

IMPORTANT!

• Image deletion cannot be undone. Before deleting an

image, make sure you no longer need it or you have a

back-up copy saved on you computer, on diskette, or

on some other medium.

•

The

indicator that is shown in the upper left corner

of the images when image information is turned on

(page 51) indicates they are protected.

4. Use [+] and [–] to select

PAGE, and then press

the shutter button.

• Be especially careful with the DELETE ALL operation,

which deletes all unprotected images in memory.

• A protected image cannot be deleted. See “Image

Protection” on page 51 for details on protecting and

unprotecting images.

•

The indicator does not appear when images are not

protected.

5. Use [+] and [–] to select the image you want to

delete.

Deleting a Single Image

•

Deleting a movie deletes all associated images as a

group.

1. Slide the Function Switch to PLAY.

2. Press MENU.

•

If you delete one or more images that are part of a

panorama, the remaining images of the panorama re-

grouped into a new panorama without the deleted im-

ages.

•

Protected images do not appear on this screen.

DELETING IMAGES

NOTE

6. Double check to make sure that you really

want to delete the image you selected.

4. Use [+] and [–] to select

ALL, and then press the

shutter button.

Deleting All Unprotected Images

The camera does not maintain open spaces in its

memory. Deleting an images causes all images follow-

ing the deleted image to be shifted up.

The following operation deletes all unprotected images. See

“Image Protection” on page 51 for details on protecting and

unprotecting images.

•

To abort the delete operation without deleting any-

thing, press any button besides [+], [–], or the shutter

button.

7. To actually delete the selected image, press

the shutter button.

1. Slide the Function Switch to PLAY.

2. Press MENU.

IMPORTANT!

•

The selected image is deleted and the next image in

sequence is selected.

The next step deletes all unprotected images in

memory. To abort this operation without deleting any-

thing, select EXIT instead of ALL.

•

Deleting a movie image deletes all the frames in both

images that make up the movie.

5. Use [+] and [–] to select ALL, and then press

the shutter button.

8. If you want to delete more images, repeat steps

5 through 7.

•

The message “NO IMAGE” appears on the monitor

screen after all the images are deleted.

3. Use [+] and [–] to select

DELETE, and then press

the shutter button.

•

To exit the image delete operation, press any button

besides [+], [–], or the shutter button.

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING IMAGE RESOLUTION

CONNECTIONS

The following operation changes the resolution of an image.

Note that image resolution can be changed downwards only

(from fine to normal, or from normal to economy).

This camera is equipped with VIDEO OUT sockets for connection to a television or video deck, and a DIGITAL interface for

connection to a computer or other equipment.

4. Use [+] and [–] to select

TOOL, and then press

the shutter button.

INPUT

IMPORTANT!

VIDEO OUT Sockets

Changing the resolution causes the original image to be

replaced with the new one.

Special video

cable that comes

with camera

VIDEO

AUDIO

5. Use [+] and [–] to select

CONVERT, and then

press the shutter button.

• Television (page 60)

1. Slide the Function Switch to PLAY.

VIDEO IN

terminal of

other device

2. Use [+] and [–] to display the image whose

resolution you want to change.

•

The resolution of movie, panorama and protected im-

ages cannot be changed.

VIDEO

Terminals

6. Press the shutter button.

3. Press MENU.

•

If you selected fine resolution image in step 2, its reso-

lution is converted to a normal image. If you selected a

normal image, it is converted to economy.

• Video Deck, Video Printer

•

If you selected an economy resolution image in step 2,

the image is unchanged.

After you are finished converting images, press MENU.

You can connect to a video tape deck and

record image to tape. Or you can connect to

a video printer to produce hard copy print-

outs of your images.

CONNECTING TO OTHER EQUIPMENT

CONNECTIONS

IMPORTANT!

Connecting to a Television

• A television must have a video input socket like the

DIGITAL Interface

You can playback images in camera memory on the screen

of a connected television.

one shown in the illustration to connect to this camera.

• This camera outputs images using NTSC format. Im-

ages do not appear normal when output to a PAL or

other type of television or video equipment.

• Battery capacity (page 18) and other displays that nor-

mally appear on the camera’s monitor screen are also

displayed on the television screen.

• Computer (page 64)

VIDEO OUT

terminal

Accessory video cable

Cables

DIGITAL

Terminal

The type of cable you

should use depends

on the type of

IN P U T

V ID E O

A U

• Other CASIO Digital

Camera (page 62)

equipment to which

you are connecting.

VIDEO IN terminal

IMPORTANT!

1. Connect one end of the video cable to the

camera and the other end to the television.

• Be sure to turn off both the camera and other equip-

ment before making any connections.

• Check the documentation that comes with your other

equipment for information you may need to know

when making connections.

• Leaving the same image displayed on a television or

computer display screen for very long periods can

cause the image to be “burned in” on the screen. When

this happens, a faint after-image remains on the

screen, even after you disconnect the camera. To avoid

this, you should not leave the same image displayed on

such a screen for very long periods.

2. Set up the television for video input.

• QV Color Printer

(page 61)

•

See the documentation that comes with the television

for information about how to do this.

3. Use the operations under “Playback” on page

33 to playback images on the television screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO OTHER EQUIPMENT

1. Connect one end of the cable that comes with

the QV Color Printer to the camera and the

other end to the printer.

Transferring Data

Connecting to another CASIO QV Digital

Camera

Connecting to a QV Color Printer

You can use a QV Color Printer to produce printouts of your

image data.

1. Slide the Function Switch of both cameras to

the PLAY position.

Connecting to another CASIO digital camera makes it pos-

sible to transfer image data between the two cameras.

2. Slide the camera’s Function Switch to PLAY

and then turn on camera power.

Supported Printer Models: QG-100, DP-300, DP-8000

2. Display the image you want to send on monitor

screen one of the cameras.

Supported CASIO Camera Models: QV-10, QV-10A, QV-

11, QV-30, QV-70, QV-100,QV-120, QV-200, QV-300, QV-

700, QV-770

Data communication cable

DIGITAL

terminal

3. Perform the QV Color Printer operations re-

quired for printing.

•

Note that data communication is impossible if the

Function Switch of either camera is in the REC posi-

tion.

•

See the documentation that comes with the QV Color

Printer for details.

DIGITAL

teminal

DIGITAL

teminal

Digital connector

•

You also will not be able to perform data communica-

tion if the monitor screen of either camera is display-

ing multi-images (page 37) or a zoomed image (page

36).

Performing a print operation for a movie prints the 16

individual frames that make up the movie.

Printing a panorama prints the individual images that

make up the panorama.

3. On the QV-770, press the

shutter button.

Setting Up For Communication

1. Turn off both cameras.

2. Connect the two cameras using a separately

available SB-62 cable.

3. Turn on both cameras.

CONNECTING TO OTHER EQUIPMENT

PC Link Software

• Cable-free IrDA data transfer with a computer is sup-

ported for LK-12S PC Link for Windows. LK-11 for

Windows and LK-22S for the Macintosh do not sup-

port IrDA communication.

4. Use [+] and [–] to select the type of operation

you want to perform.

Data Transfer and Image Resolution

Special PC Link software available from CASIO makes im-

age data transfers with a personal computer quick and easy.

The software is also designed to minimize loss of image

quality due to data transfer.

For details on how to connect to a personal computer and

exchange data, see the documentation that comes with the

PC Link software.

QV-770 AND QV-700, QV-770

•

Select SEND to send an image or RECEIVE to re-

ceive an image.

QV-770

FINE

NORMAL

ECONOMY

QV-700

FINE

NORMAL

ECONOMY

QUARTER (QV-700 only)

•

To abort the image transfer operation, press MENU.

5. On the QV-770, press the shutter button again.

•

This starts the selected image transfer operation.

•

You can transfer only one image at a time. To send

more images, repeat steps 2 through 5.

Windows Version: LK-11/LK-12S

Macintosh Version: LK-22S

QV-770 AND QV-100, QV-120, QV-200, QV-300

•

All the images that make up a movie or panorama are

treated as a single unit for image data communication

operations.

QV-770

FINE

NORMAL

ECONOMY

NORMAL

ECONOMY

Other Camera

IMPORTANT!

FINE

• This camera does not fully support the software that

comes with the LK-1, LK-1A, LK-10V connection kits

for Windows, and the LK-2, LK-2A, LK-2V, LK-21 con-

nection kits for the Macintosh. Never try to use the

software that comes with these connections kits with

this digital camera.

FINE

NORMAL

IMPORTANT!

• Take care to ensure that the cable does not become

disconnected, power is not turned off, and the position

of the Function Switch is not changed. Doing so can

cause malfunction of the camera.

• Transferring a movie or panorama to another model

QV Digital Camera (other than the QV-770) causes

the images to be ungrouped. Auto play cannot be per-

formed on other QV Digital Camera models.

QV-770 AND QV-10, QV-10A, QV-11, QV-30, QV-70

• Movie and panorama images are automatically

ungrouped when transferred to a personal computer,

so they loose their ability to be played back as movies

and panoramas. You can use Spin PhotoObject and

Spin Panorama to play movies and panoramas on

your computer. Images cannot be played back as

movies or panoramas even if they are transferred

back to the camera from the computer.

QV-770

FINE

NORMAL

ECONOMY

Other Camera

NORMAL

• QV-10, QV-10A, QV-11, QV-30, and QV-70 support nor-

mal resolution images only.

Download from Www.Somanuals.com. All Manuals Search And Download.

INFRARED DATA TRANSFER

This camera support IrDA data communication with digital

4. Receive standby screen

appears

3. Use [+] and [–] to select

IR, and then press the

shutter button.

Sending Data

equipment that supports IrTran-P protocol.

Infrared data transfer capabilities lets you exchange image

data with another digital camera without physical connec-

tion.

Transferring a movie or panorama to another model QV Digi-

tal Camera (other than the QV-770) causes the images to be

ungrouped. Auto play cannot be performed on other QV

Digital Camera models.

• This camera uses IrDA IrTran-P protocol, which was jointly

developed by NTT, Sony, Sharp, Okaya Systemware and

CASIO to provide a means for transferring digital camera

still images using infrared signals. (January 1998)

Sending a Single Image

4. Use [+] and [–] to select

IRTRAN-P, and then

press the shutter button.

5. Align the infrared port of the camera with the

port of the sending unit, and start the send op-

eration.

BUTTON OPERATION

1. Slide the Function Switch to the PLAY position.

•

See the documentation that comes with the sending

unit for details on its operation.

Receiving Data

2. Use [+] and [–] to select the image you want to

send.

Setting Up to Receive

BUTTON OPERATION

5. Use [+] and [–] to select RECEIVE, and then

press the shutter button.

MENU BUTTON OPERATION

3. Press

1. Slide the Function Switch to the PLAY posi-

tion.

6. Receive standby screen

appears.

4. Use [+] and [–] to select SEND, and then press

the shutter button.

1. Slide the Function Switch to the PLAY posi-

tion.

2. Press MENU.

5. Send standby screen ap-

pears.

2. Press

3. Use [+] and [–] to select RECEIVE, and then

press the shutter button.

7. Align the infrared port of the camera with the

port of the sending unit, and start the send op-

eration.

•

See the documentation that comes with the sending

unit for details on its operation.

INFRARED DATA TRANSFER

MENU BUTTON OPERATION

INFRARED DATA TRANSFER

6. Align the infrared port of the receiving device

that supports IrTran-P protocol.

5. Use [+] and [–] to select

SEND, and then press

the shutter button.

Sending All Images

1. Slide the Function Switch to the PLAY posi-

tion.

1. Slide the Function Switch to the PLAY posi-

tion.

2. Press MENU.

6. Use [+] and [–] to select PAGE, and then press

the shutter button.

7. Use [+] and [–] to display

the image you want to

send, and then press the

shutter button.

•

Make sure that the infrared ports are 10 to 30 centime-

ters (3.9" ~ 11.8") from each other.

3. Use [+] and [–] to select

IR, and then press the

shutter button.

3. Use [+] and [–] to select

IR, and then press the

shutter button.

To interrupt the data image send operation at any

time, press MENU.

•

Images selected for the

send operation are indi-

cated by ★.

•

Repeat step 7 if you want to send more than one im-

age.

4. Use [+] and [–] to select

IRTRAN-P, and then

press the shutter button.

4. Use [+] and [–] to select

IRTRAN-P, and then

press the shutter button.

Some devices do not support transfer of multiple im-

ages, even though they do support IrTran-P protocol.

8. Use step 6 of the procedure under “

BUTTON OPERATION” on page 67 to start the

data transfer operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

INFRARED DATA TRANSFER

5. Use [+] and [–] to select

SEND, and then press

the shutter button.

4. Use [+] and [–] to select

QV-LINK, and then press

the shutter button.

Infrared Data Transfer Precautions

Transferring Images Using PC Link Software

• Make sure that the infrared ports of the sending unit and

the receiving unit are pointed straight at each other, and

that there is nothing blocking the path between them.

• To avoid problems that occur due to sudden loss of battery

power during infrared image transfer, we recommend that

you use the separately AC adaptor specified for this cam-

era when transferring images.

With PC Link Software, Cable-free infrared image data

transfer can be performed with a personal computer that

supports IrDA1.0 protocol or later. See the documentation

that comes with your computer for details on its infrared

communication capabilities.

• This camera cannot perform infrared data transfer with any

device that does not support the IrTran-P protocol.

• Avoid performing infrared data transfers in areas expose to

direct sunlight or other strong illumination.

• Such conditions as natural outdoor light, low battery power,

too much distance between infrared ports, and misalign-

ment of infrared ports can cause failure of image transfers

or corrupted data.

1. Slide the Function Switch to the PLAY posi-

tion.

6. Use [+] and [–] to select ALL, and then press

the shutter button.

5. Align the infrared port of the camera with the

port of your computer.

2. Press MENU.

7. Use step 6 of the proce-

6. Start up the PC Link software on your com-

puter and transfer the images you want.

dure under

“

BUTTON OPERATION”

on page 67 to start the

data transfer operation.

• Proper image data transfer is impossible whenever there is

anything blocking either of the infrared ports.

• Do not locate any other infrared emitting device (such as

remote control units) or fluorescent lighting in the vicinity of

the cameras while they are performing infrared image

transfers.

• A sender ID, which shows manufacturer and model name,

normally appears on the display during infrared data com-

munication. Some equipment, however, does not transmit

a sender ID, in which case nothing appears on the display.

• Failure to be able to establish an IrDA connection can

mean that the device you are trying to communication with

does not support the IrDA standard, or that the applications

being used are not compatible. When this happens, you

probably have to connect the camera to the computer with

a separately available cable for data transfer.

3. Use [+] and [–] to select

IR, and then press the

shutter button.

TROUBLESHOOTING

Symptom

Probable Cause

Action

Symptom

Probable Cause

Action

No power

1. Batteries not loaded correctly.

2. Dead batteries

3. Wrong AC adaptor

1. Correctly load batteries (page 16).

2. Replace batteries with new ones (page 16).

3. Use only recommended AC adaptor .

Cannot perform movie re- 1. Movie Record Mode is not selected.

cording.

1. Press MODE to enter the Movie Record Mode

(page 27).

2. Delete images you no longer need from camera

memory, so there are at least two images worth

of free memory capacity (page 54).

2. Insufficient camera memory capacity.

Sudden power failure

indicator on LCD

1. Operation of Auto Power Off

2. Low battery power

3. Use of manganese batteries.

1. Turn power back on.

2. Replace batteries with new ones (page 16).

3. Replace manganese batteries with alkaline bat-

teries.

Color of recorded image is

strange.

Reflection from sunlight or light from another

source

Reorient the camera so that light is not shining di-

rectly into lens.

Batteries are about to go dead.

Replace all four batteries with a set of new ones

(page 16).

No +/– button operation

during multi-page display

Button operation during page change

Wait until an image is on the LCD before performing

a button operation.

No recording when shutter 1. Function Switch sets to PLAY.

1. Set Function Switch to REC.

2. Wait until flash unit charging is finished.

Camera is connected to a 1. Incorrect camera-TV connection

TV, but LCD monitor con-

tents do not appear on TV 2. Wrong TV set up

screen.

1. Connect correctly using the special video cable

that comes with the camera (page 60).

2. Set up the TV correctly.

button is pressed

2. Flash unit is charging.

3. The message “MEMORY FULL” is on the monitor 3. Delete images you no longer need from camera

screen. memory.

4. The message “REMAINING” is on the monitor 4. Press

to change to another resolution

screen.

mode, or delete images you no longer need from

camera memory.

Delete operation does not

operate.

All pages are protected.

Unprotect the page you want to delete (page 51).

Power failure during self-

timer operation

Low battery power

Replace batteries (page 16).

Menu icon is blue and noth-

ing happens when it is se-

lected.

Icons for functions that are disabled in the Playback

Mode are blue.

Select a different function or change to the Record

Mode.

Poor LCD image focus

Incorrect NORMAL/MACRO switch setting

Indoor fluorescent lighting

Use NORMAL for scenery and group photos, and

MACRO for close-ups (page 24).

All buttons and switches do

not operate.

Malfunction due to static electrical charge or strong

impact.

Camera is connected to a computer or QV Color

Printer.

Remove batteries and disconnect the AC adaptor if

you are using one. Restore power and turn the

camera on. If this does not work, contact your

dealer or an authorized CASIO service provider.

Poor color and brightness

when indoors

Shoot under incandescent or other non-fluorescent

lighting (page 21).

Download from Www.Somanuals.com. All Manuals Search And Download.

MESSAGES

TROUBLESHOOTING

Action

After the final “SYSTEM RESET” confirmation message

appears, press the shutter button.

ERROR

Error during data communication. Check cable connec-

tions and mode settings.

Symptom

Probable Cause

The display should return to normal after the system re-

set is complete.

Cannot exchange data be- 1. Incorrect cable connection

tween two cameras 2. Camera connected to is not turned on.

3. Function Switch sets to REC.

1. Connect correctly (page 62).

2. Turn power on after connecting cable.

3. Set Function Switch to PLAY (page 62).

FULL

Indicates that movie recording is not possible because

camera memory is full.

Delete images no longer need or reduce the resolution of

some of the images in camera memory.

Important!

•

System reset can result in a change in the order of

images stored in camera memory.

Cannot transfer data (error 1. Sending camera’s memory is empty.

keeps occurring) 2. Receiving camera’s memory is full

1. Correct the situation and try again.

2. Correct the situation and try again.

•

Corrupted images may be lost entirely.

If image data is partially corrupted, parts of the image

may not be recoverable.

MEMORY ERROR

#1, #3

CONSULT THE

OWNER’S MANUAL!

Problem with internal memory. Perform the following

procedure. The reset procedure described below can

also be used to recover from a memory error.

3. Receiving camera’s Function Switch is in REC 3. Change Function Switch setting of receiving

position.

4. Low battery (indicated by

camera to PLAY (page 62).

4. Replace batteries or use the AC adaptor (page

16).

Problem with internal memory. Contact your dealer or an

authorized CASIO service provider.

MEMORY ERROR

#2, #4

CONSULT THE

OWNER’S MANUAL!

Important!

)

The following procedure deletes all images stored in

memory. You can use the optionally available connection

kit (LK-11/LK-12S/LK-22S) to make copies of images be-

fore deleting them.

5. Disconnection of cable during data communica-

tion

5. Securely reconnect the cable.

Not enough memory for further recording. Delete some

images from memory or change resolution of stored im-

ages from FINE to NORMAL or NORMAL to ECONOMY

(page 24, 54).

MEMORY FULL

1. Holding down

MENU at the same time.

and

SYSTEM RESET

Cannot perform infrared 1. Other device does not support IrTran-P protocol. 1. Communicate only with devices that support

data communication.

IrTran-P protocol.

YES

→

SHUTTER

2. Sending and receiving units are not positioned 2. Orient the infrared ports of the two devices so

correctly.

3. Object blocking the infrared light path, another 3. Move the sending and receiving devices away

device using infrared light is in the vicinity, or

fluorescent lighting.

CALL

No images are stored in memory.

they are pointed directly at each other (page 67).

NO IMAGE

TECH SUPPORT

Not enough memory for recording in current resolution

REMAINING

from the source of the problem.

2. After checking that the SYSTEM RESET message is

on the display, press the shutter button to perform a

system reset or turn power off if you do not want to

perform a system reset.

mode. Press

to change to another resolution

mode, delete some images from memory, or change

resolution of stored images from FINE to NORMAL or

NORMAL to ECONOMY (page 24, 54).

4. Direct sunlight

4. Avoid infrared data communication in direct sun-

light.

•

Never turn off power while the system reset is in

progress! Doing so will damage camera memory are

require servicing by an authorized service provider!

Be sure to power the camera using the AC adaptor or

a new set of alkaline or lithium batteries. Weak batter-

ies or manganese batteries can result in a power fail-

ure while the system reset operation is in progress,

causing damage to camera memory.

Problem with internal memory. Contact your dealer or an

authorized CASIO service provider.

SYSTEM ERROR

CALL TECH

SUPPORT

Auto Play starts even

though it is not selected.

Activation of screen saver.

Turn off screen saver (page 40).

•

If the MEMORY ERROR message continues to ap-

pear on the display after you perform the reset proce-

dure, contact your nearest CASIO service provider.

SPECIFICATIONS

Recording System ............. Digital (JPEG base); PC Link software

can be used to input images in CAM,

Shutter ................................ CCD shutter

“Continuous Recording” is made without use of the camera’s flash.

Regardless of use of the camera’s flash, turning on and off the power

switch, as well as other operating conditions may affect the above

values.

Shutter Speed .................... 1/8 to 1/4000 second

White Balance .................... Automatic, Fixed

Self-timer ............................ 10 seconds

JPEG, TIFF and other format.

Recording Medium ............ Flash memory (4MB)

Note: The above values are obtained based on Panasonic’s alka-

line batteries and Fujifilm’s lithium batteries.

Memory Capacity............... FINE: 30 images (minimum)

Recording Modes .............. Single-image; Serial; Self-timer; Movie;

(Approximately 124KB compressed)

Panorama; Title; Macro

They may vary if other manufacturer’s batteries are used. For your

reference, the values when the camera is operated with Duracell’s

batteries are shown below.

NORMAL: 60 images (minimum)

(Approximately 62KB compressed)

Flash Modes ....................... AUTO, ON, OFF

Monitor/Viewfinder ............ 1.8-inch TFT low-glare color LCD;

ECONOMY: 120 images

(Approximately 32KB compressed)

122,100 (555 x 220) pixels

Type of Operation

Auto Play

AA-size alkaline batteries LR6

Approximately 100 minutes

Approximately 190 shots

Video Output ...................... NTSC

The above figures are approximations

only. The actual number of images de-

pends on image subject matter.

Infrared Communication .. IrDA1.0; IrTran-P compliant

Continuous Recording

Input/Output Terminals .... DIGITAL IN/OUT, VIDEO OUT, AC

Up to 120 images

adaptor connector

(total of

images)

Dimensions ........................ 129(W) x 66(H) x 38(D) mm /

Power Supply ..................... Four batteries (AA-size alkaline or

5" (W) x 2.6" (H) x 1.5" (D)

Image Element ................... 1/4-inch CCD (Total Pixels: 350,000;

lithium batteries)/AC adaptor (AD-

C620)

Effective Pixels: 330,000)

Weight ................................. Approximately 200g /

Computer Output image ... 640 x 480 pixels

7oz. (excluding batteries)

Power Consumption ......... Approximately 6.8 W

Lens .................................... Fixed focal point with macro position;

Standard Accessories ...... wrist strap; soft case; video cable; four

Battery Life

F2, f = 3.9mm

LR6 alkaline batteries;owner’s manual

The values noted below indicate the number of hours before battery

failure under normal operating temperature (25°C), as estimated by

battery manufacturers. These values are for reference only, and do

not guarantee that any particular set of batteries actually will provide

the service life indicated. Low temperatures shorten battery life.

Aperture .............................. f2, f8 auto switching/fixed

Focus Range ...................... NORMAL: 0.7m to ∞ (2.3' to ∞)

MACRO: 14cm to 16cm (5.5" to 6.3")

• The liquid crystal panel built into this camera is the product of pre-

cision engineering, with an effective pixel rate of 99.99%. This also

means, however that 0.01% of the pixels can be expected to fail to

light or to remain lit at all times.

(From surface of protective lens.)

Type of

Operation

AA-size Alkaline

Batteries LR6

AA-size Lithium

Batteries FR6

Light Metering.................... TTL center priority by CCD

Exposure Metering ............ Program AE, Aperture Priority AE

Exposure Range ................ EV +5 to 18

Continuous

Playback

Approximately 190

minutes

Approximately 320

minutes

Continuous

Recording

Approximately 690

shots

Approximately 1,430

shots

Exposure Correction......... -2EV to +2EV (1/4EV units)

Download from Www.Somanuals.com. All Manuals Search And Download.

Black Decker Pole Saw PSL12 User Manual
Bock Water heaters Water Heater Indirect Coil Tank Water Heater User Manual
Bosch Power Tools Router 10601617739 User Manual
Boss Audio Systems Car Stereo System 830UA User Manual
Brinkmann Kitchen Grill Gourmet 4 User Manual
Britax Car Seat BB0 682 00 User Manual
Cadco Electric Steamer FS 10C User Manual
Carrier Humidifier HUMCCLBP2018 User Manual
Cateye Bicycle Accessories HL EL830RC User Manual
Channel Vision GPS Receiver IR 5000 User Manual