E
Digital Camera
EX-Z4U
User’s Guide
Thank you for purchasing this CASIO
Product.
• Before using it, be sure to read the
precautions contained in this User’s Guide.
• Keep the User’s Guide in a safe place for
future reference.
• For the most up-to-date information about
this product, visit the official Exilim Website
K857PCM2DMX
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
19 GETTING READY
Contents
About This Manual ..................................................... 19
General Guide ............................................................ 20
I 2
INTRODUCTION
Camera
20
21
USB Cradle
Unpacking .................................................................... 2
Features ....................................................................... 9
Precautions .................................................................11
Monitor Screen Contents ........................................... 22
REC mode
PLAY mode
Changing the Contents of the Monitor Screen
22
24
25
General Precautions
Data Error Precautions
Operating conditions
Condensation
Lens
11
13
13
14
14
14
Indicator Lamps.......................................................... 25
Attaching the Strap .................................................... 26
Power Requirements ................................................. 26
Other
To load the battery
To remove the battery
To charge the battery
Power Supply Precautions
Turning the Camera On and Off
Configuring Power Saving Settings
26
28
28
32
36
36
15 QUICK START GUIDE
First, charge the battery! ............................................ 15
To configure display language and clock settings ..... 16
To record an image .................................................... 17
To view a recorded image .......................................... 17
To delete an image..................................................... 18
Using the On-screen Menus ...................................... 37
Configuring Display Language and Clock Settings ... 40
To configure display language and clock settings
41
Download from Www.Somanuals.com. All Manuals Search And Download.
3
INTRODUCTION
Exposure Compensation (EV Shift) ........................... 64
Adjusting White Balance ............................................ 65
43 BASIC IMAGE RECORDING
Recording an Image ................................................... 43
Adjusting White Balance Manually
66
Aiming the Camera
Recording an Image
Recording Precautions
About Auto Focus
About the REC Mode Monitor Screen
43
44
46
47
47
Using the BESTSHOT Mode ..................................... 67
Creating Your Own BESTSHOT Setup
69
Combining Shots of Two People into a Single
Image (Coupling Shot) ............................................... 71
Using the Optical Viewfinder...................................... 48
Using Zoom ................................................................ 49
Recording a Subject onto an Existing Background
Image (Pre-shot) ........................................................ 73
Optical Zoom
Digital Zoom
49
50
Recording Audio ......................................................... 75
Adding Audio to a Snapshot
Recording Your Voice
75
76
Using the Flash .......................................................... 51
Flash Unit Status
Flash Precautions
53
53
Using the Histogram .................................................. 78
REC Mode Camera Settings ..................................... 79
Using the Self-timer ................................................... 54
Specifying Image Size and Quality ............................ 55
Specifying ISO Sensitivity
80
81
81
82
83
84
Turning the On-screen Grid On and Off
Turning Image Review On and Off
Assigning Functions to the [̇] and [̈] Keys
Specifying Power On Default Settings
Resetting the Camera
To specify the image size
To specify image quality
55
56
58 OTHER RECORDING FUNCTIONS
Selecting the Focus Mode ......................................... 58
Using Auto Focus
58
60
60
61
62
63
Using the Macro Mode
Using the Pan Focus Mode
Using the Infinity Mode
Using Manual Focus
Using Focus Lock
Download from Www.Somanuals.com. All Manuals Search And Download.
4
INTRODUCTION
85 PLAYBACK
103 DELETING FILES
Basic Playback Operation.......................................... 85
Deleting a Single File ............................................... 103
Deleting All Files ...................................................... 104
Playing an Audio Snapshot
86
Flipping the Display.................................................... 87
Zooming the Display Image ....................................... 88
Resizing an Image ..................................................... 89
Cropping an Image..................................................... 90
Displaying the 9-image View ..................................... 91
105 FILE MANAGEMENT
Folders ..................................................................... 105
Memory Folders and Files
105
Protecting Files ........................................................ 106
Selecting a Specific Image in the 9-image View
92
To protect a single file
To protect all files in memory
106
107
Displaying the Calendar Screen ................................ 92
Playing a Slide Show ................................................. 93
DPOF........................................................................ 107
To specify the slideshow images
To specify the slideshow time
To set the slideshow interval
Using the Photo Stand Feature
95
96
96
97
To configure print settings for a single image
To configure print settings for all images
108
109
II
PRINT Image Matching .............................................110
Exif Print ....................................................................110
Using USB DIRECT-PRINT ...................................... 111
Using the FAVORITE Folder .....................................113
Rotating the Display Image........................................ 98
Using Image Roulette ................................................ 99
Adding Audio to a Snapshot .................................... 100
To copy a file to the FAVORITE folder
To display a file in the FAVORITE folder
To delete a file from the FAVORITE folder
To delete all files from the FAVORITE folder
113
114
115
116
To re-record audio
101
Playing Back a Voice Recording File....................... 102
Download from Www.Somanuals.com. All Manuals Search And Download.
5
INTRODUCTION
117 OTHER SETTINGS
130 USING A MEMORY CARD
Configuring Sound Settings ......................................117
Using a Memory Card .............................................. 131
To configure sound settings
To set the volume level
117
118
To insert a memory card into the camera
To remove a memory card from the camera
Formatting a Memory Card
131
132
132
133
Specifying an Image for the Startup Screen ............118
Configuring Power Down Image Settings.................119
Memory Card Precautions
Copying Files ........................................................... 134
To copy all the files in built-in memory to
Specifying the File Name Serial Number
a memory card
To copy a file from a memory card to built-in memory 135
134
Generation Method .................................................. 121
Using the Alarm ........................................................ 122
To set an alarm
Stopping the Alarm
122
123
136 VIEWING IMAGES ON A COMPUTER
Setting the Clock ...................................................... 123
To select your Home Time zone
To set the current time and date
Changing the Date Format
123
124
125
Using the Camera with a Windows Computer ........ 136
USB Connection Precautions
141
Using the Camera with a Macintosh Computer....... 141
Using World Time ..................................................... 125
USB Connection Precautions
145
To display the World Time screen
To configure World Time settings
To configure summer time (DST) settings
125
126
127
Operations You Can Perform from Your
Computer.................................................................. 145
Using a Memory Card to Transfer Images to a
Computer.................................................................. 146
Changing the Display Language ............................. 128
Formatting Built-in Memory...................................... 128
Memory Data ............................................................ 147
DCF Protocol
Memory Directory Structure
Image Files Supported by the Camera
Built-in Memory and Memory Card Precautions
147
147
149
149
Download from Www.Somanuals.com. All Manuals Search And Download.
6
INTRODUCTION
150 USING THE CAMERA WITH A COMPUTER
164 APPENDIX
Using the Album Feature ......................................... 150
Menu Reference....................................................... 164
Indicator Lamp Reference ....................................... 166
Creating an album
150
151
152
154
157
Selecting an Album Layout
Configuring Detailed Album Settings
Viewing Album Files
REC mode
167
168
168
PLAY mode
USB Cradle Indicator Lamps
Saving an Album
Troubleshooting Guide ............................................. 169
Installing the Software from the CD-ROM ............... 157
Display Messages
172
About the bundled CD-ROM
Computer System Requirements
157
158
Specifications ........................................................... 173
Main Specifications
173
Installing Software from the CD-ROM
in Windows ............................................................... 159
Getting Started
Viewing the Contents of the “Read me” File
Installing an Application
Viewing User Documentation (PDF Files)
User Registration
Exiting the Menu Application
159
160
160
161
161
161
Installing Software from the CD-ROM on
a Macintosh .............................................................. 162
Installing Software
Viewing User Documentation (PDF Files)
162
163
Download from Www.Somanuals.com. All Manuals Search And Download.
7
INTRODUCTION
IMPORTANT!
• The USB driver (mass storage) uses Phoenix
Technologies Ltd. software.
• The contents of this manual are subject to change
without notice.
• CASIO COMPUTER CO., LTD. assumes no
responsibility for any damage or loss resulting from
the use of this manual.
Compatibility Software Copyright C 1997
Phoenix Technologies Ltd., All Rights Reserved.
• Other company, product and service names used
herein may also be trademarks or service marks of
others.
• Photo Loader and Photohands are the property of
CASIO COMPUTER CO., LTD. Except as stipulated
above, all copyrights and other related rights to these
applications revert to CASIO COMPUTER CO., LTD.
• CASIO COMPUTER CO., LTD. assumes no
responsibility for any loss or claims by third parties
which may arise through the use of the EX-Z4U.
• CASIO COMPUTER CO., LTD. shall not be held
liable for any damages or losses suffered by you or
any third party due to the use of Photo Loader and/or
Photohands.
• CASIO COMPUTER CO., LTD. assumes no
responsibility for any damage or loss caused by
deletion of data as a result of malfunction, repairs, or
battery replacement. Be sure to back up all important
data on other media to protect against its loss.
• The SD logo is a registered trademark.
• Windows, Internet Explorer, and DirectX are
registered trademarks of Microsoft Corporation.
• Macintosh is a registered trademark of Apple
Computer, Inc.
I Copyright Restrictions
Except for the purposes of your own personal enjoyment,
unauthorized copying of snapshot files and audio files
violates copyright laws and international contracts.
Distribution to third parties of such files over the Internet
without permission of the copyright holder, whether for
profit or for free, violates copyright laws and international
contracts.
•
MultiMediaCard is a trademark of Infineon
Technologies AG of Germany, and licensed to the
MultiMediaCard Association (MMCA).
• Acrobat and Acrobat Reader are trademarks of
Adobe Systems Incorporated.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
INTRODUCTION
• Easy Image Transfer
Transfer images to a computer simply by placing the
camera onto the USB cradle.
Features
• 4.0 million Effective Pixels
A high-resolution megapixel CCD provides 4.0 million
effective pixels (4.23 million total pixels) for images that
print beautifully.
• Photo Stand feature
A slideshow of images in file memory can be played while
the camera is on its USB cradle.
• 2.0-inch TFT color LCD monitor screen
• BESTSHOT
• 12X seamless zoom
3X optical zoom, 4X digital zoom
Simply select the sample scene that matches the type of
image you are trying to record and the camera performs
troublesome setups automatically for beautiful pictures
every time.
• 10MB Flash memory
Images can be recorded without using a memory card.
• Coupling Shot and Pre-shot
• Multi Auto Focus
Coupling Shot lets you combine two subjects into a single
image, while Pre-shot lets you add a subject to a
previously recorded background image. This means you
can create images that include you and your friend, even
if you are the only two people around. You can use
Coupling Shot and Pre-shot by selecting the applicable
sample images in the BESTSHOT mode.
When “Multi” is selected for the Auto Focus area, the
camera takes simultaneous meter readings at seven
different points and automatically selects the best one.
This makes it possible to avoid erroneous focusing on the
background, and ensure proper focus for a wide range of
image types.
• Pan Focus
• Image Roulette Feature
Images cycle like a slot machine on the display until one
of them remains.
This feature lets you lock the focus point and ensures that
you do not miss that special moment when it happens.
• Support for SD memory cards and MMC (MultiMedia
Cards) for memory expansion
• Triple Self-timer mode
The self-timer can be set up to repeat three times,
automatically.
• Easy Charging
Just place the camera onto the USB cradle to charge its
battery.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
INTRODUCTION
• Real-time histogram
• Voice Recording
An on-screen histogram lets you adjust exposure as you
view the effect on overall image brightness, which makes
shooting under difficult lighting conditions easier than
ever before.
Quick and easy recording of voice input.
• After Recording
Adds audio to images after they are recorded.
• Selectable Sound Settings
• World Time
You can configure different sounds to play whenever you
turn on the camera, press the shutter release button half-
way or all the way, or perform a key operation.
A simple operation sets the current time for your current
location. You can select from among 162 cities in 32 time
zones.
• DCF Data Storage
• Alarm
DCF (Design rule for Camera File system) data storage
protocol provides image inter-compatibility between the
digital camera and printers.
A built-in alarm helps to keep you on time for important
events, and even can be used in place of an alarm clock.
You can also have a specific image appear, or an audio
file to play when the alarm time is reached.
• Digital Print Order Format (DPOF)
Images can be printed easily in the sequence you want
using a DPOF compatible printer. DPOF can also be used
when specifying images and quantities for printing by
professional print services.
• Album Function
HTML files are generated automatically to create an
album of recorded images. Album contents can be viewed
and printed using a standard Web browser. Images can
also be incorporated into Web pages quickly and easily.
II
• PRINT Image Matching Compatible
II
Images include PRINT Image Matching data (mode
• Calendar screen
setting and other camera setup information). A printer that
A simple operation displays a full-month calendar on the
camera’s monitor screen. Each day of the full-month
calendar shows a thumbnail of the first image recorded
for that date, which helps to make searching for a
particular image quicker and easier.
II
supports PRINT Image Matching reads this data and
adjusts the printed image accordingly, so your images
come out just the way you intended when you recorded
them.
• Snapshot + Audio Mode
Adds audio to a snapshot.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
INTRODUCTION
• USB DIRECT-PRINT support
Precautions
Your camera supports USB DIRECT-PRINT, which was
developed by Seiko Epson Corporation. When connected
directly to a printer that supports USB DIRECT-PRINT,
you can select images to print and start the print
operation directly from the camera.
General Precautions
Be sure to observe the following important precautions
whenever using the EX-Z4U.
• Bundled with Photo Loader and Photohands
Your camera comes bundled with Photo Loader, the
popular application that automatically loads images from
your camera to your PC. It also comes with Photohands,
and application that makes image retouching quick and
easy.
All references in this manual to “this camera” and “the
camera” refer to the CASIO EX-Z4U Digital Camera.
• Never try to take pictures or use the built-in display while
operating a motor vehicle or while walking. Doing so
creates the danger of serious accident.
• Never try to open the case of the camera or attempt your
own repairs. High-voltage internal components create the
risk of electric shock when exposed. Always leave
maintenance and repair work up to a CASIO authorized
service center.
• Never look at the sun or any other bright light through the
camera’s viewfinder. Doing so can damage your eyesight.
• Keep the small parts and accessories of this camera out
of the reach of small children. If swallowed accidentally,
contact your physician immediately.
• Never fire the flash in the direction of a person operating
a motor vehicle. Doing so can interfere with the driver’s
vision and create the danger of accident.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
INTRODUCTION
• Never fire the flash while it is too close to the subject’s
eyes. Intense light from the flash can cause eye damage
if it is fired too close to the eyes. This is especially true
with young children. When using the flash, the camera
should be at least one meter (3.3´) from the eyes of the
subject.
• Keep the camera away from water and other liquids, and
never let it get wet. Moisture creates the danger of fire
and electric shock. Never use the camera outdoors in the
rain or snow, at the seashore or beach, in the bathroom,
etc.
• Should foreign matter or water ever get into the camera,
immediately turn it off. Next, remove the camera’s battery
and/or unplug the AC adaptor power cord from the power
outlet, and contact your dealer or nearest CASIO
authorized service center. Using the camera under these
conditions creates the danger of fire and electric shock.
• Should you ever notice smoke or a strange odor coming
out of the camera, immediately turn it off. Next, taking
care you do not burn your fingers, remove the camera’s
battery and/or unplug the AC adaptor power cord from the
power outlet, and contact your dealer or nearest CASIO
authorized service center. Using the camera under these
conditions creates the danger of fire and electric shock.
After making sure there is no more smoke coming from
the camera, take it to your nearest CASIO authorized
service center for repair. Never attempt your own
maintenance.
• Never use the AC adaptor to power any other device
besides this camera. Never use any other AC adaptor
besides the one that comes with this camera.
• Never cover the AC adaptor with a quilt, blanket, or other
cover while it is in use, and do not use it near a heater.
• At least once a year, unplug the AC adaptor power cord
from the power outlet and clean the area around the
prongs of the plug. Dust build up around the prongs can
create the danger of fire.
• If the camera’s case should ever become cracked due to
dropping it or otherwise subjecting it to rough treatment,
immediately turn it off. Next, remove the camera’s battery
and/or unplug the AC adaptor power cord from the power
outlet, and contact your dealer or nearest CASIO
authorized service center.
• Never use the camera inside of an aircraft or in any other
areas where its use is prohibited. Doing so can result in
an accident.
• Physical damage and malfunction of this camera can
cause the data stored in its memory to be deleted. Be
sure to always keep backup copies of data by transferring
them to personal computer memory.
• Never open the battery compartment cover, disconnect
the AC adaptor from the camera, or unplug the AC
adaptor from the wall socket while recording images.
Doing so will not only make storage of the current image
impossible, it can also corrupt other image data already
stored in file memory.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
INTRODUCTION
Data Error Precautions
Operating conditions
• Your digital camera is manufactured using precision
digital components. Any of the following creates the risk
of corruption of data in file memory.
• This camera is designed for use in temperatures ranging
from 0°C to 40°C (32°F to 104°F).
• Do not use or keep the camera in the following areas.
— In areas subject to direct sunlight
— Removing the battery or memory card, or setting the
camera onto the USB cradle while the camera is
performing a record or memory access operation
— Removing the battery, removing the memory card, or
placing the camera onto the USB cradle while the
operation lamp is still flashing after you turn off the
camera
— In areas subject to high humidity or dust
— Near air conditioners, heaters, or other areas subject
to temperature extremes
— Inside of a closed vehicle, especially one parked in the
sun
— In areas subject to strong vibration
— Disconnecting the USB cable, removing the camera
from the USB cradle, or disconnecting the AC adaptor
from the USB cradle while a data communication
operation is being performed
— Low battery power
— Other abnormal operations
Any of the above conditions can cause an error message to
appear on the monitor screen (page 172). Follow the
instructions provided by the message to eliminate the
cause of the error.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
INTRODUCTION
Condensation
Lens
• When you bring the camera indoors on a cold day or
otherwise expose it to a sudden change of temperature,
there is the possibility that condensation can form on the
exterior or on interior components. Condensation can
cause malfunction of the camera, so you should avoid
exposing it to conditions that might cause condensation.
• To keep condensation from forming, place the camera
into a plastic bag before moving it into a location that is
much warmer or colder than your current location. Leave
it in the plastic bag until the air inside the bag has a
chance to reach the same temperature as the new
location. If condensation does form, remove the battery
from the camera and leave the battery compartment
cover open for a few hours.
• Never apply too much force when cleaning the surface of
the lens. Doing so can scratch the lens surface and cause
malfunction.
• Fingerprints, dust, or any other soiling of the lens can
interfere with proper image recording. Never touch the
lens with your fingers. You can remove dust particles
from the lens surface by using a lens blower to blow them
off. Next, wipe the surface of the lens with a soft lens
cloth.
Other
• The camera may become slightly warm during use. This
does not indicate malfunction.
• If the exterior of the camera needs cleaning, wipe it with a
soft, dry cloth.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
QUICK START GUIDE
First, charge the battery!
1. Load the battery (page 26).
2. Place the camera onto the USB cradle to charge the
battery (page 28).
1
• It takes about two hours to achieve a full charge.
1
Stopper
2
2
PLA
Y
R
E
C
MENU
3
SET
D
ISP
Download from Www.Somanuals.com. All Manuals Search And Download.
15
QUICK START GUIDE
To configure display language and clock settings
• Be sure to configure the following settings
before using the camera to record images.
(See page 40 for details.)
1. Press the power button to turn on the camera.
2. Press [̆] to select the language you want.
1
3. Press [SET] to register the language setting.
PL
AY
REC
4. Use [̆], [̄], [̇], and [̈] to select the geographical
M
E
N
U
area you want, and then press [SET].
SET
5. Use [̆] and [̄] to select the city you want, and then
D
IS
P
press [SET].
2, 3, 4, 5, 6, 7, 8, 9
6. Use [̆] and [̄] to select the summer time (DST)
setting you want, and then press [SET].
7. Use [̆] and [̄] to select the date format setting you
want, and then press [SET].
8. Set the date and the time.
9. Press [SET] to register the clock settings and exit the
setting screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
QUICK START GUIDE
To record an image
To view a recorded image
(See page 43 for details.)
(See page 85 for details.)
Green
operation lamp
2
2
99
1600 1200
NORMAL
1
1
4
IN
1
/
1000
F2.6
PL
AY
PL
AY
REC
REC
03/12/24
:
12 58
M
E
N
U
M
E
N
U
SET
SET
Focus frame
3
D
IS
P
D
IS
P
3
1. Press the power button to turn on the camera.
1. Press the power button to turn on the
camera.
2. Align the mode selector with “REC”.
2. Align the mode selector with “PLAY”.
3. Point the camera at the subject, use the monitor
screen or viewfinder to compose the image, and
then press the shutter release button half way.
3. Use [̇] and [̈] to scroll through the
images.
• When proper focus is achieved, the focus frame turns green
and the green operation lamp lights.
4. Holding the camera still, gently press the shutter
release button.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
QUICK START GUIDE
To delete an image
(See page 103 for details.)
2
1
P
LA
Y
R
E
C
M
E
N
U
SE
T
D
IS
P
3, 4, 5, 6
1. Press the power button to turn on the camera.
2. Align the mode selector with “PLAY”.
3. Press [̄] (
).
4. Use [̇] and [̈] to display the image you want to delete.
5. Use [̆] and [̄] to select “Delete”.
• To exit the image delete operation without deleting anything, select
“Cancel”.
6. Press [SET] to delete the image.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
GETTING READY
This section contains information about things you need to
know about and do before trying to use the camera.
I Button Operations
Button operations are indicated by the button name inside
of brackets ([ ]).
About This Manual
I On-screen Text
On-screen text is always enclosed by double quotation
marks (“ ”).
This section contains information about the conventions
used in this manual.
I Terminology
The following table defines the terminology used in this
manual.
I File Memory
The term “file memory” in this manual is a general term that
refers to the location where your camera is currently storing
the images you record. File memory can be any one of the
following three locations.
This term as used in this
Means this:
manual:
“this camera” or “the
camera”
The CASIO EX-Z4U Digital
Camera
• The camera’s built-in Flash memory
• An SD memory card loaded in the camera
• A MultiMediaCard loaded in the camera
“file memory”
The location where the
camera is currently storing
images you record (page 44)
For more information about how the camera stores images,
see page 130.
“battery”
The NP-20 Rechargeable
Lithium Ion Battery
“optional charger unit”
The optionally available
CASIO BC-10L Charger Unit
Download from Www.Somanuals.com. All Manuals Search And Download.
19
GETTING READY
General Guide
The following illustrations show the names of each component, button, and switch on the camera.
Camera
I Front
I Back
7
8
1
2
9
0
3
A
4
1 Shutter release button
2 Power button
3 Flash
7 Viewfinder
B
8 Operation lamp
9 Mode selector
0 [MENU] button
A Zoom button
B Strap ring
P
LA
Y
R
E
C
M
E
N
U
4 Self-timer lamp
5 Microphone
6 Lens
SE
T
C [SET] button
D [̆][̄][̇][̈]
E [DISP] button
F Monitor Screen
G Speaker
D
IS
P
G
F
5
E
6
D
C
Download from Www.Somanuals.com. All Manuals Search And Download.
20
GETTING READY
I Bottom
USB Cradle
Simply placing your CASIO digital camera onto the USB
cradle lets you perform the following tasks.
• Battery charging (page 28)
• Automatic transfer of images to a computer (page 136)
• Viewing of images using the Photo Stand slideshow
feature (page 97).
H
I
J
I Front
H Battery compartment cover
I Connector
J Tripod screw hole
1
2
3
1 Camera connector
2 [USB] lamp
* Use this hole when attaching to a tripod.
3 [USB] button
4 [CHARGE] lamp
5 [PHOTO] button
K
5
4
I Back
6 [DC IN 5.3V]
(AC adaptor connector)
7 [USB]
K Stopper
L Battery compartment
M Memory card slot
L
(USB port)
6
7
M
Download from Www.Somanuals.com. All Manuals Search And Download.
21
GETTING READY
Monitor Screen Contents
The monitor screen uses various indicators and icons to keep you informed of the camera’s status.
REC mode
1 Flash Mode indicator
4 Self-timer
9
Built-in memory selected
for data storage.
Memory card selected
1234 5
6
None Auto
None 1-Image
Flash Off
Self-timer 10 sec
Self-timer 2 sec
Triple self-timer
for data storage.
10
s
Flash On
7
8
9
0 Date and time
A EV value
2s
Red-eye reduction
•
If the camera detects that
flash is required while auto
flash is selected, the flash on
indicator will appear when the
shutter release button is
pressed half way.
x3
C
5 REC modes
B Battery capacity
C Focus frame
Snapshot
BESTSHOT
0
•
•
Focusing complete: Green
Focusing failed: Red
Snapshot Audio
Voice Recording
2 Focus Mode indicator
None Auto Focus
Macro
B
A
6 Memory capacity
(Remaining number of storable
images)
Pan Focus
Infinity
Manual Focus
7 Image size
2304 ҂ 1728
pixels
3 White balance indicator
2304 ҂ 1536 (3:2) pixels
None Auto
1600 ҂ 1200
1280 ҂ 960
640 ҂ 480
pixels
pixels
pixels
Sunlight
Shade
8 Quality
Light Bulb
Fluorescent
Manual
FINE
NORMAL
ECONOMY
Download from Www.Somanuals.com. All Manuals Search And Download.
22
GETTING READY
D
D Digital zoom indicator
E Shutter speed value
•
An out of range aperture or shutter speed
causes the corresponding monitor screen
value to turn amber.
E
F
G
F Aperture value
G ISO sensitivity
H Zoom indicator
H
•
•
Left side indicates optical zoom.
Right side indicates digital zoom.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
GETTING READY
PLAY mode
12
3
1 PLAY mode file type
Snapshot
5 Quality
FINE
4
5
6
NORMAL
ECONOMY
Snapshot Audio
Voice Recording
6
Built-in memory selected for data
storage.
2 Image protection indicator
3 Folder number/File number
4 Image size
Memory card selected for data storage.
7
7 Date and time
8 Battery capacity
2304 ҂ 1728
pixels
8
2304 ҂ 1536 (3:2) pixels
1600 ҂ 1200
1280 ҂ 960
640 ҂ 480
pixels
pixels
pixels
IMPORTANT!
• Some information may not
display properly if you display an
image that was recorded using a
different digital camera model.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
GETTING READY
Changing the Contents of the Monitor
Screen
Each press of the [DISP] button changes the contents of
the monitor screen as shown below.
Indicator Lamps
You can find out the operational status of the camera and
the USB cradle at a glance by checking the color of the
indicator lamps, and whether a lamp is lit or flashing. For
details, see “Indicator Lamp Reference” on page 166.
Indicators
on
(page 22)
Histogram
on
(page 78)
Indicators
off
Monitor
screen off
Self-timer lamp
Green operation lamp
PL
AY
REC
M
EN
U
IMPORTANT!
SET
• You cannot turn off the monitor screen in the
following cases:
D
IS
P
In the PLAY mode, in the BESTSHOT mode.
• You cannot use the [DISP] button to change the
contents of the monitor screen while standing by for
or performing audio recording.
Red operation lamp
• In the Voice Recording mode, you can only turn
indicators on and off.
[USB] lamp
[CHARGE] lamp
Download from Www.Somanuals.com. All Manuals Search And Download.
25
GETTING READY
Attaching the Strap
Power Requirements
Attach the strap to the strap ring as shown in the
illustration.
Your camera is powered by a rechargeable lithium ion
battery (NP-20).
To load the battery
PL
AY
REC
M
E
N
U
1. While pressing the battery compartment
cover on the bottom of the camera, slide the
cover in the direction indicated by the arrow,
and then swing it open.
SET
D
IS
P
PL
AY
REC
M
E
N
U
SET
D
IS
P
IMPORTANT!
• Be sure to keep the strap around your wrist when
using the camera to protect against accidentally
dropping it.
• The supplied strap is intended for use with this
camera only. Do not use it for any other purpose.
• Never swing the camera around by the strap.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
GETTING READY
2. While pulling the stopper in the direction
indicated by the arrow in the illustration, align
the arrow mark on the battery with the arrow
mark on the camera and slide the battery into
the camera.
3. Swing the battery compartment cover closed,
and then slide it in the direction indicated by
the arrow.
Stopper
IMPORTANT!
• Use only the special NP-20 rechargeable lithium ion
battery to power this camera. Use of any other type
of battery is not supported.
Arrow marks
NP-20
The battery is not charged when you purchase the
camera. You need to charge the battery before using
the camera for the first time (page 28).
• Push the bottom of the battery, and make sure that
the stopper securely locks the battery in place.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
GETTING READY
To remove the battery
To charge the battery
1. Open the battery compartment cover.
1. Connect the bundled AC adaptor to the [DC IN
5.3V] connector of the USB cradle.
2. Pull the stopper in the direction indicated by
the arrow.
2. Extend the prongs of the AC adaptor, and
then plug it into a household power outlet.
• This will cause the battery to come part way out of
the slot.
Stopper
[DC IN 5.3V]
USB cradle
AC Adaptor
3. Release the stopper and pull the battery from
the camera.
• Take care so you do not drop the battery.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
GETTING READY
IMPORTANT!
3. Turn off the camera.
• It takes about two hours to achieve a full charge.
Actual charging time depends on current battery
capacity and charging conditions.
4. Set the camera onto
the USB cradle.
PLA
Y
R
E
C
MENU
• Use only the USB cradle (CA-21A) that comes with
the camera, the optionally available USB cradle (CA-
21), or the optionally available charger unit (BC-10L)
to charge the special NP-20 rechargeable lithium ion
battery. Never use any other charging device.
• Use only the bundled AC adaptor. Never use any
other type of AC adaptor. Do not use optionally
available AD-C40, AD-C620 and AD-C630 AC
adaptors with this camera.
• Do not place the camera
onto the USB cradle
while it is turned on.
SET
D
ISP
• The [CHARGE] lamp
on the USB cradle
should turn red,
indicating that charging
has started. When
charging is complete,
the [CHARGE] lamp
will turn green.
• Make sure that the camera connector of the USB
cradle is securely inserted into the camera’s
connector as far as it will go.
[CHARGE] lamp
• The [CHARGE] lamp may remain amber colored and
the charge operation may not start right away if you
try to charge immediately after using the camera
(which causes battery to become warm) or when it is
too hot or too cold where you are performing the
charge operation. If this happens, simply wait until
the battery reaches normal temperature. The
[CHARGE] lamp will turn red and charging will start
when the battery temperature returns to the
allowable charging temperature range.
5. After charging is complete, remove the
camera from the USB cradle.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
GETTING READY
• If the [CHARGE] lamp starts flashing red, it means
that an error occurs while charging. An error can be
caused by any of the following: a problem with the
USB cradle, a problem with the camera, or a problem
with the battery or how it is loaded. Remove the
camera from the USB cradle and see if it works
normally.
I If the camera works normally
1. Continue using the camera until the current
charge is used up, and then charge the
battery.
• You can use the USB cradle to charge the camera’s
battery, to exchange data with a computer over a
USB connection, or when using the Photo Stand
feature only.
I If the camera does not work normally
This can mean there is a problem with how the battery is
loaded.
NOTE
1. Remove the battery from the camera and
check the battery contacts for dirt. If the
contacts are dirty, wipe them clean with a dry
cloth.
• The AC adaptor is designed for operation on power
ranging from 100V AC to 240V AC. Note, however,
that the shape of the power cord plug varies
according to country or geographic area. It is up to
you to find out if the shape of the AC adaptor power
cord plug is compatible with local power outlets when
traveling abroad.
2. Check to make sure that the AC adaptor’s
power cord is connected securely to the
power outlet and USB cradle.
• If the same symptoms occur again when you place
the camera on the USB cradle after taking the above
steps, contact a CASIO authorized service center.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
GETTING READY
*2 Normal Recording Conditions
I Battery Life Guidelines
• Temperature: 23°C (73°F)
• Monitor Screen: On
• Zoom operation between full wide to full telephoto
every 30 seconds, during which two images are
recorded, one image with flash; power turned off and
back on every time 10 images are recorded.
The battery life guideline values given below indicate the
amount of time under the conditions defined below the
table, until power automatically turns off due to battery
failure. They do not guarantee that the battery will provide
the amount of service indicated. Low temperatures and
continued use reduce battery life.
*3 Continuous Playback Conditions
• Temperature: 23°C (73°F)
Operation
Approximate Battery Life
540 shots (90 minutes)
• Scroll one image about every 10 seconds
Number of Shots, Continuous
Recording*1 (Recording Time)
*4 Voice recording times are based on continuous
Number of Shots, Normal
recording.
140 shots (70 minutes)
Recording*2 (Recording Time)
Continuous Playback*3
(Continuous Snapshot Recording)
Continuous Voice Recording*4
• The above values are based on a new battery starting
from a full charge. Repeated charging shortens battery
life.
150 minutes
130 minutes
• Battery life is greatly affected by how much you use flash,
zoom and other functions, and how long you leave power
turned on.
Supported Battery: NP-20 (Rated Capacitance: 680mAh)
*1 Continuous Recording Conditions
• Temperature: 23°C (73°F)
• Monitor screen: On
• Flash: Off
• Image recorded about every 10 seconds
Download from Www.Somanuals.com. All Manuals Search And Download.
31
GETTING READY
I Tip to Make the Battery Last Longer
Power Supply Precautions
• If you do not need the flash while recording, select
(flash off) for the flash mode. See page 51 for more
information.
• You can also conserve battery power by using the [DISP]
button to turn off the monitor screen.
Note the following precautions when handling or using the
battery and the optional charger unit.
I Battery Handling Precautions
G SAFETY PRECAUTIONS
Be sure to read the following Safety Precautions before
trying to use the battery for the first time. Keep these safety
precautions and all operating instructions on hand for
future reference.
I Low Battery Indicator
The following shows how the battery capacity indicator on
the monitor screen changes as battery power is used. The
indicator means that remaining battery power is low.
Note that you will not be able to record images while the
NOTES
• The term “battery” in this manual refers to the CASIO
NP-20 Rechargeable Lithium Ion Battery.
battery indicator is
. Charge the battery immediately
whenever either of these indicators appears.
• Use only the USB cradle (CA-21A) that comes with
the camera, the optionally available USB cradle (CA-
21), or the optionally available charger unit (BC-10L)
to charge the special NP-20 rechargeable lithium ion
battery. Never use any other charging device.
Battery Level
Indicator
High
Low
Download from Www.Somanuals.com. All Manuals Search And Download.
32
GETTING READY
• Failure to observe any of the following precautions
while using the battery creates the risk of overheating,
fire, and explosion.
— Never use any other type of charger except the
optional charger unit specified for the battery.
— Never try to use the battery to power any other
device other than this camera.
— Never use or leave the battery near open flame.
— Never place the battery in a microwave oven, throw
it into fire, or otherwise expose it to intense heat.
— Make sure the battery is oriented correctly when you
load it into the camera or attach it to the optional
charger unit.
— Never carry or store the battery together with items
that can conduct electricity (necklaces, pencil lead,
etc.)
— Never try to take the battery apart, modify it in any
way, or expose it to strong impact.
— Do not immerse the battery in fresh water or salt
water.
— Do not use or leave the battery under direct
sunlight, in an automobile parked in the sun, or in
any other area subject to high temperatures.
• Should you ever notice leakage, strange odor, heat
generation, discoloration, deformation, or any other
abnormal condition while using, charging, or storing a
battery, immediately remove it from the camera or
optional charger unit and keep it away from open flame.
• If the battery does not achieve full charge after the
normal charging time has passed, stop charging.
Continued charging creates the risk of overheating, fire,
and explosion.
• Battery fluid can damage your eyes. Should battery
fluid get into your eyes accidentally, immediately rinse
them with clean tap water and then consult a physician.
• Be sure to read page 28 of this User’s Guide and the
instructions that come with the optional charger unit
before using or charging the battery.
• If the battery is to be used by young children, make
sure that a responsible adult makes them aware of the
precautions and proper handling instructions and make
sure that they handle the battery correctly.
• Should fluid from the battery accidentally get onto
clothing or your skin, immediately rinse it off with clean
tap water. Prolonged contact with battery fluid can
cause skin irritation.
Download from Www.Somanuals.com. All Manuals Search And Download.
33
GETTING READY
G PRECAUTIONS DURING USE
G BATTERY STORAGE PRECAUTIONS
• The battery is designed for use with this CASIO digital
camera only.
• Use only the USB cradle that comes with the camera or
the specified optional charger unit to charge the
battery. Never use any other type of charger unit for
charging.
• Make sure you remove the battery when you do not
plan to use the camera for a long time. A battery left in
the camera discharges very small amounts of power
even when power is turned off, which can lead to a
dead battery or the need for longer charging before the
next use.
• A new battery is not charged. Be sure to charge the
battery before using it for the first time.
• Store the battery in a cool, dry place (20°C (68 °F) or
lower).
• Use of a battery in cold environments shortens the
operating time you can expect on a full charge. Charge
the battery in a location where the temperature is in the
range of 10°C to 35°C (50°F to 95°F). Charging
outside this temperature range can cause charging to
take longer than normal or even cause charging to fail.
• Very limited operation following a full charge indicates
that the battery has reached the end of its service life.
Replace the battery with a new one.
G USING THE BATTERY
• See page 28 of this manual or the instructions that
come with the optional charger unit for information
about charging procedures and charging times.
• When transporting a battery, keep it either loaded in
the camera or stored in its case.
• Never wipe the battery with thinner, benzene, alcohol,
or other volatile agents or chemically treated rags.
Doing so can cause deformation of the battery and lead
to malfunction.
Download from Www.Somanuals.com. All Manuals Search And Download.
34
GETTING READY
• Use the AC adaptor where it will not be
splashed with water. Water creates the risk of
fire and electric shock.
• Do not place a vase or any other container
filled with liquid on top of the AC adaptor.
Water creates the risk of fire and electric
shock.
I USB Cradle and AC Adaptor Precautions
• Never use an electrical outlet whose voltage
is outside the rating marked on the AC
adaptor. Doing so can create the danger of
fire or electric shock. Use only the bundled
AC adaptor specified for this camera.
• Do not allow the AC adaptor cord to become
cut or damaged, do not place heavy objects
on it, and keep it away from heat. A damaged
power cord creates the risk of fire and electric
shock.
Caution!
• Make sure you always remove the camera from the USB
cradle before connecting or disconnecting the AC
adaptor.
• Charging, USB data communication, and using the Photo
Stand feature can cause the AC adaptor to become
warm. This is normal and does not indicate malfunction.
• Unplug the AC power cord from the power outlet
whenever you are not using it.
• Never try to modify the AC adaptor cord, or
subject it to severe bending, twisting, or
pulling. Doing so creates the risk of fire and
Caution!
electric shock.
• Never touch the AC adaptor while your hands
are wet. Doing so creates the risk of electric
shock.
• Never place a blanket or any other cover on the AC
adaptor. Doing so creates the risk of fire.
• Do not overload extension cords or wall
outlets. Doing so creates the danger of fire
and electric shock.
• Should the cord of the AC adaptor become
damaged (exposed internal wiring), request a
replacement from a CASIO authorized service
center. A damaged AC adaptor cord creates
the danger of fire or electric shock.
Download from Www.Somanuals.com. All Manuals Search And Download.
35
GETTING READY
Turning the Camera On and Off
Configuring Power Saving Settings
Press the power button to turn the camera on and off.
Pressing the power button to turn on the camera causes
the green operation lamp to light temporarily. Press the
power button again to turn off the camera.
You can configure the settings described below to
conserve battery power.
Sleep
: Automatically turns off the monitor screen
if no operation is performed for a specified
amount of time in the REC mode.
Performing any button operation causes
the monitor screen to turn back on.
Auto Power Off: Turns off power if you do not perform any
operation for a specified amount of time.
ON/OFF
Power button
Green operation lamp
1. Turn on the camera, and then align the mode
selector with “REC” or “PLAY”.
IMPORTANT!
2. Press [MENU].
• If camera power is turned off by the Auto Power Off
feature, press the power button to turn it back on
again.
3. Use [̇] and [̈] to select the “Set Up” tab.
• Turning on camera power while the REC mode is
selected by the mode selector causes the lens to
extend from the camera. Make sure there is nothing
in front of the camera that can be hit by the lens
when you turn on the camera.
4. Use [̆] and [̄] to select the feature whose
setting you want to configure, and then press
[SET].
Download from Www.Somanuals.com. All Manuals Search And Download.
36
GETTING READY
G See page 37 for information about how to use
menus.
Using the On-screen Menus
Pressing [MENU] displays menus on the monitor screen
that you can use to perform various operations. The menu
that appears depends on whether you are in the REC
mode or the PLAY mode. The following shows an example
menu procedure in the REC mode.
To configure this feature:
Sleep
Select this setting:
Sleep
Auto Power Off
Auto Power Off
5. Use [̆] and [̄] to change the currently
Mode selector
1. Turn on the camera,
selected setting, and then press [SET].
and then align the
mode selector with
• Available Sleep settings are: “30 sec”, “1 min”, “2 min”,
and “Off”.
PLAY
REC
“REC” to enter the
REC mode.
• Available Auto Power Off settings are: “2 min” and
“5 min”.
MENU
• If you want to enter the
PLAY mode instead,
you would align the
mode selector with
“PLAY”.
• Note that the Sleep feature does not operate in the
PLAY mode.
• Pressing any button while the camera is in the Sleep
state immediately turns the monitor screen back on.
• The Auto Power Off and Sleep features are disabled
in the following cases.
— When the camera is connected to a computer or
some other device through the USB cradle
— While a slideshow is in progress
— While playing back a voice recording file
Download from Www.Somanuals.com. All Manuals Search And Download.
37
GETTING READY
G Menu Screen Operations
2. Press [MENU].
When you want to do this:
Move between tabs
Do this:
Tab
MENU
[MENU]
[SET]
Press [̇] and [̈].
Move from the tab to the
settings
Press [̄].
SET
Move from the settings to
the tab
Press [̆].
Move between the settings
Press [̆] and [̄].
DISP
Display the options
Press [̈] or press [SET].
Press [̆] and [̄].
available for a setting
Settings
Selection cursor (indicates the
currently selected item)
Select an option
[̆][̄][̇][̈]
Register an option
selection and exit the menu Press [SET].
screen
Register an option
selection and return to the
menu screen
Press [̇].
Exit the menu screen
Press the [MENU] button.
Download from Www.Somanuals.com. All Manuals Search And Download.
38
GETTING READY
3. Press [̇] or [̈] to select the tab you want,
and then press [SET] to move the selection
cursor from the tab to the settings.
6. Perform one of the following operations to
apply the setting you configured.
To do this:
Perform this key operation:
Press [SET].
4. Use [̆] and [̄] to
select the feature
whose setting you
want to configure,
and then press [̈].
Apply the setting and exit
the menu screen.
Apply the setting and
return to feature selection
in step 4.
Press [̇].
Apply the setting and
return to tab selection in
step 3.
1. Press [̇].
• Instead of pressing [̈],
2. Use [̆] to move back up to
tab selection.
Example: To select the
you could also press
“REC Mode”
item.
[SET].
• See “Menu Reference” on page 164 for more information
about menus.
5. Use [̆] and [̄] to change the currently
selected setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
39
GETTING READY
IMPORTANT!
Configuring Display Language and Clock
Settings
• The camera’s clock settings are cleared whenever
power is totally cut off. This can happen if the battery
goes dead while the camera is not being supplied
power by the USB cradle. The clock setting screen
will appear automatically the next time you turn on
power after the settings are cleared. Set the date
and time before using the camera.
• The current date and time settings will be cleared if
the battery remains dead without being charged for
about two days.
Be sure to configure the following settings before using the
camera to record images.
• Display language
• Home city
• Date Style
• Date and time
Note that the current date and time settings are used by
the camera to generate the date and time that are stored
along with image data, etc.
• Recording images without configuring the clock
settings causes incorrect time information to be
registered. Be sure to configure the clock settings
before using the camera.
Download from Www.Somanuals.com. All Manuals Search And Download.
40
GETTING READY
3. Use [̆], [̄], [̇], and
[̈] to select the
To configure display language and clock
settings
geographical area
where you live, and
then press [SET].
1. Press the power button to turn on the camera.
2. Use [̆], [̄], [̇], and
[̈] to select the
language you want,
and then press [SET].
4. Use [̆] and [̄] to
select the name of the
city where you live,
and then press [SET].
: Japanese
English
: English
Français : French
Deutsch : German
Español : Spanish
5. Use [̆] and [̄] to select the summer time
Italiano
Português : Portuguese
: Chinese (Complex)
: Italian
(DST) setting you want, and then press [SET].
When you want to do this:
Select this setting:
Keep time using summer time
(Daylight Saving Time)
: Chinese (Simplified)
: Korean
On
Off
Keep time using standard time
Download from Www.Somanuals.com. All Manuals Search And Download.
41
GETTING READY
6. Use [̆] and [̄] to
change the date format
setting, and then press
[SET].
7. Set the current date
and the time.
Example: December 24, 2003
To do this:
Do this:
Change the setting at the current
cursor location
To display the date like this:
03/12/24
Select this format:
Press [̆] and [̄].
Press [̇] and [̈].
YY/MM/DD
DD/MM/YY
MM/DD/YY
Move the cursor between settings
24/12/03
Toggle between 12-hour and 24-
hour timekeeping
Press [DISP].
12/24/03
8. Press [SET] to register the settings and exit
the setting screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
42
BASIC IMAGE RECORDING
This section describes the basic procedure for recording an
image.
IMPORTANT!
• Make sure your fingers or the strap does not block
the flash, microphone or lens.
Flash
Recording an Image
Aiming the Camera
Microphone
Lens
Use both hands to hold the camera still when shooting an
image. Holding the camera with one hand increases the
chance of movement, which can blur your images.
• Horizontal
Hold the camera
still in both
NOTE
• Your image will be blurred if you move the camera
when pressing the shutter release button. Press the
shutter release button carefully, taking care that
there is no camera movement. This is especially
important when available lighting is low, which slows
down the shutter speed.
hands, with your
arms firmly
against your
sides.
• Vertical
When holding
the camera
vertically, make
sure that the
flash is above
the lens. Hold
the camera still
with both hands.
Download from Www.Somanuals.com. All Manuals Search And Download.
43
BASIC IMAGE RECORDING
3. Compose the image
on the monitor screen
so the main subject is
within the focus
99
1600 1200
NORMAL
Recording an Image
Your camera automatically adjusts shutter speed in
accordance with the brightness of the subject. Images you
record are stored in the camera’s built-in memory, or to a
memory card if you have one loaded in the camera.
• When an optionally available SD memory card or
MultiMediaCard (MMC) is loaded in the camera, images
are stored on the card (page 130).
IN
frame.
03/12/24
:
12 58
• The focusing range of
the camera in the Auto
Focus mode is
Focus frame
approximately 40cm
(1.3 feet) to infinity (∞)
(page 58).
Power button
1. Press the power
button to turn on the
camera.
• You can compose images using either the monitor
screen or the optical viewfinder (page 48).
• This causes an image
or a message to appear
on the monitor screen.
ON/OFF
• When using the optical viewfinder to compose
images, you can use the [DISP] button to turn off the
monitor screen and conserve battery power.
Mode selector
2. Align the mode
selector with “REC”.
• This enters the REC
PLAY
REC
mode for image
recording.
MENU
Download from Www.Somanuals.com. All Manuals Search And Download.
44
BASIC IMAGE RECORDING
G Operation Lamp and Focus Frame Operation
4. Press the shutter release
button half way to focus the
image.
When you see this:
It means this:
Green focus frame
Green operation lamp
The image is in focus.
• When you press the shutter
release button half way, the
camera’s Auto Focus feature
automatically focuses the image,
and displays the shutter speed
and aperture values.
Red focus frame
Flashing green operation lamp
The image is not in focus.
Shutter release
button
Flash
• Make sure you are not
blocking the lens or the
flash with your fingers
while recording an
image.
Green operation lamp
• You can tell whether the
image is focused by
observing the focus frame
and the green operation
lamp.
Lens
Download from Www.Somanuals.com. All Manuals Search And Download.
45
BASIC IMAGE RECORDING
5. After making sure that the
image is focused properly,
press the shutter release
button the rest of the way
down to record.
Recording Precautions
• Never open the battery compartment cover or place the
camera onto the USB cradle while the green operation
lamp is flashing. Doing so not only causes the current
image to be lost, it can also corrupt images already stored
in file memory and even lead to malfunction of the
camera.
Shutter release
button
• The number of images that can
be stored in memory depends on
the resolution setting you are
using (pages 55,174).
• Never remove the memory card while an image is being
recorded to the memory card.
• Fluorescent lighting actually flickers at a frequency that
cannot be detected by the human eye. When using the
camera indoors under such lighting, you may experience
some brightness or color problems with recorded images.
• When “Auto” is selected for the ISO sensitivity setting
(page 80), the camera automatically adjusts its sensitivity
in accordance with the brightness of the subject. This can
cause some static noise to appear in images of relatively
dark subjects.
• Press the shutter release button gently to avoid
camera movement.
• When recording a dimly lit subject while “Auto” is selected
for the ISO sensitivity setting (page 80), the camera
increases sensitivity and uses a slower shutter speed.
Because of this, you need to guard against camera
movement if you have flash turned off (page 51).
• If unwanted light is shining on the lens, shade the lens
with your hand when recording the image.
Download from Www.Somanuals.com. All Manuals Search And Download.
46
BASIC IMAGE RECORDING
About Auto Focus
About the REC Mode Monitor Screen
• Auto Focus tends not to work well if the camera is moved
during recording, or when recording the types of subjects
listed below.
— Solid color walls or objects with little contrast
— Strongly backlit objects
— Polished metal or other brightly reflective objects
— Venetian blinds or other horizontally repeating patterns
— Multiple images that are varying distances from the
camera
• The image shown on the monitor screen in the REC
mode is a simplified image for composing purposes. The
actual image is recorded in accordance with the image
quality setting currently selected on your camera. The
image saved in file memory has much better resolution
and detail than the REC mode monitor screen image.
• Certain levels of subject brightness can cause the
response of the REC mode monitor screen to slow down,
which causes some static noise in the monitor screen
image.
— Subjects in poorly lit areas
— Moving subjects
• Note that a green operation lamp and focus frame do not
necessarily guarantee that an image is in focus.
• If Auto Focus does not produce the results you want for
some reason, try using focus lock (page 63) or manual
focus (page 62).
Download from Www.Somanuals.com. All Manuals Search And Download.
47
BASIC IMAGE RECORDING
IMPORTANT!
Using the Optical Viewfinder
• The frame that is visible inside of the viewfinder
indicates the image recorded at a distance of about
one meter (3.3´). When the subject is closer than one
meter, the recorded image will be different from what
you see inside the viewfinder frame.
You can conserve battery power by turning off the
camera’s monitor screen (page 25) and using the optical
viewfinder to compose images.
• Since the monitor screen shows exactly what will be
recorded, always use it for composing your images in
the Macro and Manual Focus modes.
Short distance
to subject
Viewfinder frame
Download from Www.Somanuals.com. All Manuals Search And Download.
48
BASIC IMAGE RECORDING
Using Zoom
Your camera is equipped with two types of zoom: optical
zoom and digital zoom.
Optical Zoom
The range of the optical zoom factor is shown below.
Zoom out
Zoom in
Optical Zoom Factor Range: 1X to 3X
2. Compose the image and then press the
shutter release button.
1. In the REC mode, press
the zoom button to
NOTES
REC
change the zoom factor.
• The optical zoom factor also affects the lens
aperture.
MENU
• Use of a tripod is recommended to protect against
hand movement when using the telephoto setting
(zoom in).
Zoom button
To do this:
Zoom out
Zoom in
Press this side of the zoom button:
(Wide Angle)
(Telephoto)
Download from Www.Somanuals.com. All Manuals Search And Download.
49
BASIC IMAGE RECORDING
Digital zoom indicator
5. Hold down the
(Telephoto) zoom
Digital Zoom
Digital zoom is activated after you reach the maximum
optical zoom factor (3X). It enlarges the part of the image
at the center of the image screen. The range of the digital
zoom factor is shown below.
button to increase the
optical zoom factor.
• When the digital zoom
factor reaches its
maximum value (3X), it
stops momentarily. Keep
Digital Zoom Factor Range: 3X to 12X
(in combination with optical
zoom)
the
(Telephoto)
zoom button depressed
and zoom will switch
over to digital zoom
automatically.
Zoom indicator
1. In the REC mode, press [MENU].
2. Use [̇] and [̈] to select the “REC” tab.
• Switching to digital zoom causes the zoom indicator
to appear on the monitor screen. The zoom indicator
shows the current approximate zoom factor.
3. Use [̆] and [̄] to select “Digital Zoom”, and
then press [̈].
Digital
Zoom
4. Select “On”, and then press [SET].
• Selecting “Off” disables digital zoom.
Optical Zoom
1x
3x
Current zoom factor
12x
6. Compose the image and then press the
shutter release button.
Download from Www.Somanuals.com. All Manuals Search And Download.
50
BASIC IMAGE RECORDING
IMPORTANT!
Using the Flash
• Digital zoom is disabled whenever the monitor
screen is turned off (page 25).
• Using digital zoom can cause degradation of the
recorded image.
Perform the following steps to select the flash mode you
want to use.
1. In the REC mode, press [MENU].
2. Press [̄] (
) to select
the flash mode.
MENU
• Each press of [̄] (
)
cycles through the flash
mode settings shown below
on the monitor screen.
SET
DISP
[̄] (
)
Flash mode indicator
Download from Www.Somanuals.com. All Manuals Search And Download.
51
BASIC IMAGE RECORDING
I About Red-eye Reduction
To do this:
Select this setting:
None
Have the flash fire automatically when
required (Auto Flash)
Using the flash to record at night or in a dimly lit room can
cause red spots inside the eyes of people who are in the
image. This is caused when the light from the flash reflects
off of the retina of the eye. When red-eye reduction is
selected as the flash mode, the camera performs two pre-
flash operations, one designed to cause the irises in the
eyes of any people in the image to close, and one for the
Auto Focus operation. This is followed by another flash
operation for actual recording of the image.
Turn off the flash (Flash Off)
Always fire the flash (Flash On)
Fire a pre-flash followed by image
recording with flash, reducing the
chance of red-eye in the image (Red-
eye reduction)
In this case, the flash fires automatically
when required
IMPORTANT!
Note the following important points when using red-
eye reduction.
3. Record the image.
IMPORTANT!
• Red-eye reduction does not work unless the people
in the image are looking directly at the camera during
the pre-flash. Before pressing the shutter release
button, call out to the subjects so they all look at the
camera while the pre-flash operation is performed.
• Red-eye reduction may not work very well if the
subjects are located far away from the camera.
• The flash unit of this camera fires a number of times
when you record an image. The initial flashes are
pre-flashes, which the camera uses to obtain
information that it uses for exposure settings. The
final flash is for recording. Make sure that you keep
the camera still until the shutter releases.
• Image recording may not be performed if you press
the shutter release button while the red operation
lamp is flashing.
Download from Www.Somanuals.com. All Manuals Search And Download.
52
BASIC IMAGE RECORDING
Flash
Flash Unit Status
Flash Precautions
You can find out the current flash unit status by pressing
the shutter release button half way and checking the
monitor screen and red operation lamp.
Take care that your fingers do
not block the flash when you
hold the camera. Covering the
flash with your finger can
greatly reduce its
effectiveness.
The
indicator is also
• You may not be able to achieve the desired results using
a flash if the subject is too close or too far away.
• The flash takes anywhere from a few seconds to as long
as 10 seconds to attain full charge after being fired. The
actual time required depends on the battery level,
temperature, and other conditions.
shown on the monitor
screen when the flash unit
is ready to fire.
Red operation lamp*
* Red operation lamp
When the red operation
lamp is this:
• The flash unit may not be able to charge when battery
It means this:
power is low. Low battery power is indicated by
(Flash
Flashing
Lit
Flash unit is charging
Off) on the monitor screen, and when the flash fails to fire
properly resulting in poor image exposure. When these
symptoms occur, charge the camera’s battery as soon as
possible.
Flash unit is ready to fire
• When the red-eye reduction mode (
) is selected, flash
intensity is adjusted automatically in accordance with the
exposure. The flash may not fire at all when the subject is
brightly lit.
• Using flash in combination with another light source
(daylight, fluorescent light, etc.) can result in abnormal
image colors.
Download from Www.Somanuals.com. All Manuals Search And Download.
53
BASIC IMAGE RECORDING
To do this:
Select this setting:
Using the Self-timer
Specify a 10-second self-timer
Specify a 2-second self-timer
Specify Triple Self-timer
Disable the self-timer
10 sec
2 sec
X3
The self-timer lets you select either a 2-second or 10-
second delay of the shutter release after you press the
shutter release button. A Triple Self-timer feature lets you
perform three consecutive self-timer operations to record
three images.
Off
• With the Triple Self-timer, the camera records a
series of three images in the sequence described
below.
1. In the REC mode, press [MENU].
2. Use [̇] and [̈] to select the “REC” tab.
1. The camera performs a 10-second countdown and
then records the first image.
3. Use [̆] and [̄] to select “Self-timer”, and
then press [̈].
2. The camera prepares to record the next image.
The amount of time required for preparation
depends on the camera’s current “Size” and
“Quality” settings, the type of memory (built-in or
card) you are using for image storage, and
whether or not the flash is charging.
4. Use [̆] and [̄] to select the self-timer time
you want to use, and then press [SET].
• Selecting “Off” in step 4 disables the self-timer.
3. After preparation is complete, the indicator “1sec”
appears on the monitor screen, and another
image is recorded one second later.
4. Steps 2 and 3 are repeated once more to record
the third image.
Download from Www.Somanuals.com. All Manuals Search And Download.
54
BASIC IMAGE RECORDING
5. Record the image.
Self-timer lamp
Specifying Image Size and Quality
• When you press the
shutter release button,
the self-timer lamp
You can specify the image size and image quality to suit
the type of image you are recording.
flashes and the shutter
releases after the self-
timer reaches the end
of its countdown.
To specify the image size
1. In the REC mode, press [MENU].
• You can interrupt an
ongoing self-timer
countdown by pressing
the shutter release
button while the self-
timer lamp is flashing.
2. Use [̇] and [̈] to select the “REC” tab.
3. Use [̆] and [̄] to select “Size”, and then
press [̈].
4. Use [̆] and [̄] to select the setting you
NOTE
want, and then press [SET].
• The “2 sec” self-timer setting is best when shooting
with a slow shutter speed, because it helps to avoid
blurring of images due to hand movement.
2304 x 1728
: 2304 x 1728
pixels
2304 x 1536 (3:2): 2304 x 1536 (3:2) pixels
1600 x 1200
1280 x 960
640 x 480
: 1600 x 1200
: 1280 x 960
pixels
pixels
pixels
:
640 x 480
Download from Www.Somanuals.com. All Manuals Search And Download.
55
BASIC IMAGE RECORDING
NOTES
To specify image quality
• If you plan to make large prints of your images or
otherwise use them in applications where high-
resolution is your top priority, select the “2304 x
1728” image size.
• If you plan to send images as e-mail attachments or
otherwise use them in applications where data
economy is your top priority, select the “640 x 480”
image size.
1. In the REC mode, press [MENU].
2. Use [̇] and [̈] to select the “REC” tab.
3. Use [̆] and [̄] to select “Quality”, and then
press [̈].
• Selecting the “2304 x 1536 (3:2)” image size records
images with a 3:2 (vertical : horizontal) aspect ratio,
which is optimal for printing on paper with an aspect
ratio of 3:2.
4. Use [̆] and [̄] to select the setting you
want, and then press [SET].
To get this:
Select this setting:
Fine
Very high quality, but large file size
Normal quality
Normal
Small file size, but low quality
Economy
Download from Www.Somanuals.com. All Manuals Search And Download.
56
BASIC IMAGE RECORDING
NOTE
• Use the “Fine” setting when image quality is your top
priority and file size is secondary. Conversely, use
the “Economy” setting when file size is your top
priority and image quality is secondary.
IMPORTANT!
• Actual file size depends on the type of image you
record. This means that the remaining image
capacity noted on the monitor screen may not be
exactly accurate (pages 22 and 174).
Download from Www.Somanuals.com. All Manuals Search And Download.
57
|