Impressa S
Avantgarde Series
Fully Automatic
Coffee & Espresso Center
with Clearyl Water Care System
Operating Instructions
and Warranty
Customer Service 1-800-220-5701
Impressa S9 Avantgarde shown
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice: Your Impressa S Avantgarde Series has a 3-prong
grounded plug. To reduce the risk of electrical shock this
plug will fit in an outlet only one way. If the plug does not fit
in the outlet contact a qualified electrician. DO NOT modify
the plug in any way.
JURA-CAPRESSO
Jura was founded in 1931 in Switzerland. Capresso was
founded in 1994 in the USA. Both companies have joined
forces in the US to bring you the finest Fully Automatic
Coffee Centers available anywhere. With innovative and
user-friendly features, high quality materials, clear instruc-
tions and superb customer service, we are sure you will
experience the best coffee, espresso, cappuccino or latte
you have ever had. We hope you will enjoy your new Fully
Automatic Coffee Center and will recommend it to your
friends. For more information about our products visit our
CAUTION
This appliance is for household and commercial use. Any
servicing other than cleaning and user maintenance should
be performed by an authorized service representative.
• Do not immerse base in water or try to disassemble.
• To reduce the risk of fire or electric shock, do not remove
the base. No user serviceable parts inside. Repair should
be done by authorized service personnel only.
Michael Kramm, President
Customer Service
1-800-220-5701
• Check voltage to be sure that the voltage indicated on the
name plate agrees with your voltage.
• Never use warm or hot water to fill the water container!
Use cold water only!
• Keep your hands and the cord away from hot parts of the
appliance during operation.
Mon-Thu 9AM – 9PM • Fri 9AM – 8PM • Sat 9AM – 5PM
Eastern Standard Time.
email: [email protected]
• Never clean with scouring powders or hard implements.
Jura-Capresso LLC.
81 Ruckman Road, Closter, NJ 07624
201-767-3999 • Fax: 201-767-9684
2.
Download from Www.Somanuals.com. All Manuals Search And Download.
FIG. 1
1. Height-Adjustable Dual Coffee Spout
2. Operating Display (Fig.2)
3. Removable Water Tank
4. Low Water Flotation Device(Inside)
5. Clearyl Water Care Cartridge
(Not Installed)
6. Lid for Water Tank
7. Holder for Clearyl Water Cartridge
8. Aroma Protection Lid
9. Cover for Bean Container
10. Lid for Ground Coffee Funnel
11. Opening for Ground Coffee
12. Warming Plate
13. Steam System (Fig.3)
14. Hot Water Release
10
11
12
13
14
15
15a*
16
17
18
19
9
8
7
6
5
4
3
2
1
15. Steam Nozzle
15a. Dual-Frother-Plus (Fig.14,14a, 14b)
16. Used Coffee Container
17. Removable Grid
18. Removable Drawer/Used Water Tray
19. Cover for Rotary Dial and
A La Carte Button (Fig. 3A)
FIG. 1a
d
FIG. 1b
a
c
a. Scoop
b
b. Cleaning tablets
c. Water indicator
d. Clearyl filter
Main Power Switch
* frothXpress-Plus System see Fig. 15 to 17a
3.
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Display
FIG. 2
Steam & Hot Water System
FIG. 3
FIG. 3A
FIG. 4
M
SELECT
PRODUCT
A
B
N
O
K
“Hot Water
Position”
E
Chrome
cover
P
Steam
Nozzle
C
D
F
L
Q
G
Display Dialog System
ON/OFF Button
K. STEAM PORTION Button
N.
O.
P.
A.
B.
C.
D.
E.
F.
A La Carte Button
Ground Coffee Button
Rotary Dial w/push button
L. Selector Switch for
Coffee or Hot Water
1-CUP Espresso Button
1-CUP Coffee Button
RINSE Button
M. PERMANENT STEAM
Q.
Service Cover
(do not remove)
Button
2-CUP Espresso Button
2-CUP Coffee Button
G.
4.
Download from Www.Somanuals.com. All Manuals Search And Download.
FIG. 5
FIG. 6
FIG. 7
FIG. 8a
FIG. 8b
FIG. 9
FIG. 10
FIG. 11
FIG. 12
FIG. 13
5.
Download from Www.Somanuals.com. All Manuals Search And Download.
FIG. 14
FIG. 14a
FIG. 14b
FIG. 15
2
3
Frothing:
down
Steaming
up
1
Tip
Sleeve
Rod
FIG. 15a
FIG. 16
FIG. 17
FIG. 17a
Frothing range
Siphoning
with
flexible
hose
frothXpress
Plus
attached
Steam only
no siphoning
DIAL
Steaming range
6.
Download from Www.Somanuals.com. All Manuals Search And Download.
FIG. 19
FIG. 20
FIG. 21
FIG. 18
FIG. 22
FIG. 23
FIG. 24
FIG. 25
7.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
PAGE
Important Safeguards / Jura Capresso.................1-2
Drawings.........................................................3-7
PAGE
14.
Clearyl Water Filter Cartridge............................ 18
14a. Installing and Activating
1.
2.
3.
Product Warranty Registration ................................
Operating Instructions / Customer Service.............
Welcome to the Impressa S Avantgarde.................
9
9
9
9
the Clearyl Water Cartridge .................................. 18
14b. Replacing the Clearyl Water Cartridge ................. 19
15.
Water Hardness Monitor....................................... 19
3a. “Crema Coffee” and Pressure Brewing...................
15a. Changing the Water Hardness Monitor ................ 20
16. Programming....................................................... 20
3b. Different Coffee Drinks............................................ 10
3c. Coffee Facts............................................................ 10
16.1 Coffee Strength..................................................... 21
16.2 Coffee Volume (Cup Size)..................................... 21
16.3 Temperature.......................................................... 22
16.4 Hot Water Volume................................................. 22
16.5 Steam Duration ..................................................... 22
16.6 Economy Modes ................................................... 23
16.7 Actual Time ........................................................... 23
16.8 Auto-On................................................................. 24
16.9 Auto-Off................................................................. 24
16.10 Language .............................................................. 24
16.11 Display................................................................... 24
16.12 Information ............................................................ 25
4.
5.
6.
Please Don’t / Please Do...................................... 10
Factory Settings ...................................................... 11
Preparing the Machine for the First Time........... 11
6a. Filling the Water Tank.............................................. 11
6b. Filling the Bean Container....................................... 11
6c. Turning the Machine On.......................................... 12
7.
8.
9.
Adjusting the Grinder .............................................. 12
Daily Preparation..................................................... 13
Brewing Coffee and Espresso.............................. 13
9a. Overriding Cup Size ................................................ 13
9b. The A La Carte Button ............................................ 14
10. Cappuccino and Latte........................................... 14
10a. Using the Dual Frother Plus .................................... 14
10b. Cleaning the Dual Frother Plus ............................... 15
10c. Using the frothXpress Plus System
17.
Care and Maintenance Messages ..................... 25
17.1 Manual Maintenance Cycles ................................. 26
17.2 Removing Stones etc. from the Burr Grinder ....... 27
17.3 General Cleaning Instructions............................... 27
17.4 Emptying the System before Transport................. 27
with Milk Container ................................................. 15
10d. Using the frothXpress Plus System
18.
Automatic Cleaning Cycles ................................... 28
with Flexible Hose................................................... 16
10e. Hot Chocolate, Café Mocha.................................... 16
10f. Cleaning the frothXpress Plus................................. 16
10g. Cleaning the Milk Container.................................... 17
11. Using Ground Coffee .............................................. 17
12. Using Hot Water...................................................... 17
13. Water Care .............................................................. 17
18.1 Cleaning with Special Tablet.............................. 28
18.2 Decalcifying........................................................... 28
18.3 Decalcifying Procedure ......................................... 29
19.
20.
21.
22.
Tips for Better Coffee............................................ 30
Error Messages / Troubleshooting ......................... 30
Supplies................................................................ 32
Limited Warranty ................................................... 32
8.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. PRODUCT WARRANTY REGISTRATION
pressure brewing system - well known in commercial applica-
tions - was adapted and refined by Jura coffee specialists and is
the trademark of each Jura-Capresso coffee center. This two-
step brewing system ensures optimal coffee extraction and will
finish every cup with a rich layer of "crema" - proof for perfectly
pressure brewed coffee. The built-in low-noise, commercial coni-
cal burr grinder grinds beans to the correct fineness (6 settings).
A separate filler funnel lets you use pre-ground coffee. The sec-
ond Thermoblock generates unlimited steam instantly. With the
Dual Frother Plus you can steam and froth (for cappuccino) or
just steam milk (for lattes). The unique frothXpress Plus system
siphons, heats, steams and froths milk automatically. You can
also program a specific amount of frothed/steamed milk and the
machine will always deliver the correct volume. A separate hot
water spout lets you prepare a cup of tea or any other hot bev-
erage in seconds. With four pre-set coffee buttons, an A La
Carte button and the easy-to-use Rotary dial you can brew
exactly the coffee you desire.You can re-program cup size,
coffee strength and temperature. You can select from different
Please read the enclosed product registration form now. Fill it out
and mail or fax it to us within two weeks after purchasing your
Important: This registration is part of your warranty (chapter 22).
2. OPERATING INSTRUCTIONS / CUSTOMER SERVICE
Thank you for choosing this Jura-Capresso product.
• Please study these Operating Instructions carefully before
using your new machine. We highly recommend viewing the
enclosed DVD. Select S Avantgarde Series.
• Also included is a Quick Reference Guide. Keep it next to
your machine until you are familiar with all functions.
• For further information please call our TOLL FREE number:
1-800-220-5701, Mon-Fri 9AM – 9PM & Sat 9AM – 5PM
Eastern Standard Time. If you call at any other time please
leave a message including your telephone number and a time
you can be reached. You can send us a FAX at: 201-767-9684
or EMAIL us at [email protected].
Please note: if you lose your Operating Instructions or the Quick maintenance set-ups. The machine will automatically remind you
Reference Guide, you can download a printable copy from our
when to refill water, clean, change filter or decalcify. A special
section lets you check how many coffees you prepared with the
different coffee buttons.
3. WELCOME TO THE IMPRESSA S AVANTGARDE SERIES
This fully automatic espresso coffee center is completely pro-
grammable and extremely user friendly. With two independent
stainless steel Thermoblock heating systems it can switch from
brewing coffee to frothing milk without any up- or down-time. It
3a. "CREMA COFFEE" AND PRESSURE BREWING
According to the majority of coffee experts, grinding, tamping
and brewing under high pressure is the ideal extracting process
for maximum flavor and aroma. Your Jura-Capresso automatic
can prepare 1 or 2 cups of excellent, professional quality espresso coffee center will always produce espresso and coffee with a
or coffee at a time with just a push of a button. The two-step
thick, foamy layer called "crema." The crema traps the fine
9.
Download from Www.Somanuals.com. All Manuals Search And Download.
aromatics and the light gaseous flavors that register on the
palate.The high pressure and the short brewing time prevent the
extraction of bitter oils and release less caffeine than any other
brewing method. You will always make the absolute freshest
and most aromatic cup of coffee. This is the reason why many
European restaurants and hotels serve only fresh pressured
brewed coffee. Experiment with your new machine and prepare
yourself the best and most enjoyable cup of coffee!
coffees and instant coffees.
• Espresso is not a bean, it's the way the coffee is roasted and
prepared. Typical US espresso roasts result in darker beans with
an oily surface. European espresso roasts are medium brown
with no or very little oils on the surface.
All Display Messages Are Shown in RED
4. PLEASE, DON’T... (or you void your warranty protection):
• Never pull out the drawer during the brewing process. Only
pull the drawer when the display instructs you or when the
display shows SELECT PRODUCT.
• Never fill instant coffee into the bean container or ground coffee
funnel; it can damage the brewing chamber.
• Never fill sugar coated coffee beans into the bean container.
• Never fill frozen beans into the bean container. If you store
beans in the freezer, let them thaw 3 to 4 hours before filling
them into the bean container.
• Never fill anything other than coffee beans into the bean
container (no chocolate, rice, nuts, spices, etc.)
• Never fill anything but fresh, cold clean water into the water
container, except when decalcifying (chapter 29).
• Never use mineral or carbonated water. You can use tap
water, bottled water, spring water, distilled water and reverse
osmosis water.
3b. DIFFERENT COFFEE DRINKS
Here are some guidelines for the most popular coffee drinks:
• Ristretto: 1/2 to 1 oz. of coffee. Sweeten to taste.
• Espresso: 1 to 2 oz. coffee. Sweeten to taste.
• Double Shot: 3 to 4 oz. of coffee. Sweeten to taste.
• Crema Coffee: 5 to 8 oz. of coffee.
• Cappuccino: Espresso plus 3 to 4 oz. of hot frothed milk.
• Latte: Espresso plus 3-5 oz. steamed milk with little or no froth.
• Café Mocha: Make Espresso then add chocolate syrup to the
milk before frothing/steaming.
TIP: Experiment with the size of your milk based drinks. For
stronger coffee taste add more coffee, for more milk taste add
more frothed milk.
3c. COFFEE FACTS
• Caffeine is tasteless. A "strong" coffee or espresso is mostly
the result of the amount of coffee in relation to the amount of
water. The longer a bean is roasted, the less caffeine it has.
• Arabica and Robusta are two genetically different kinds of
beans. "Arabica" beans have more flavor and a little less caffeine
than "Robusta" beans which are mostly used in lower priced
• Never repair or open the machine yourself. All repairs should
be performed only by an authorized service center.
PLEASE, DO...
• Fill water tank with fresh, cold water only.
10.
Download from Www.Somanuals.com. All Manuals Search And Download.
• Remove any foreign particles (small stones) from coffee beans.
• Let frozen beans thaw for 3 to 4 hours before pouring them
into the bean container.
• Display: AM/PM and OZ. Other settings 24 hour and ML
(milliliters)
• Economy Mode: Off
Other settings: Economy 1, Economy 2
• Time: --. (not set)
5. FACTORY SETTINGS
Each machine leaves the factory with the settings described
below. To change any of these settings (chapter 16).
• All coffee buttons are set to temperature HIGH.
• 1-CUP Espresso button (Fig. 2,C) 2 oz./ STRONG.
• 2-CUP Espresso button (Fig. 2,F) 2 oz. per cup / STRONG.
• 1-CUP Coffee button (Fig. 2,D) 5 oz./ STRONG.
• 2-CUP Coffee button (Fig. 2,G) 5 oz. per cup / STRONG.
Other settings: Each of the four buttons above can be set
from 1 oz. to 8 oz. of coffee per cup.
Other setting: Set a time
• Unit On: --. (not set)
Other setting: Set a time that the unit turns on automatically.
(Requires that you first set a time.)
6. PREPARING THE MACHINE FOR THE FIRST TIME
• Make sure all accessories, literature and any other items are
removed from the bean container and the water tank.
• DO NOT install the Clearyl water filter now. (chapter 14)
• Make sure the machine sits on an even, flat surface and the
drawer and used coffee container are inserted (Fig. 1).
• Plug-in machine.
• A La Carte button (Fig. 3A,N) 7 oz.
• Hot water (WATER PORTION): 5 oz. Other settings: The hot
water release can be set from 1 oz. to 15 oz.
• 5-hour auto shut-off. Other settings: manual shut off, auto
shut-off from 1/2 hour to 15 hours after last use.
• Water hardness setting: level 2.
6a. FILLING THE WATER TANK
Please note: Only use fresh, cold water. Never fill water tank
with carbonated water, milk or any other liquid.
• Remove the water tank, rinse and fill with fresh, cold water.
• Replace water tank and make sure that it engages securely.
Other settings: “blank”, 1, 3, 4
• Filter: FILTER NO (Clearyl Water Care Cartridge: not installed)
Other Settings: FILTER YES (chapter 14a).
• Coffee temperature: HIGH for all coffee buttons
Other setting: NORMAL
6b. FILLING THE BEAN CONTAINER
Please note: To insure that your conical burr grinder will work
for a long time, do not use it with any kind of coated or flavored
beans (all coating and flavors contain sugar or sugar substances).
Such coating can damage the burrs. Using such beans voids the
warranty. Have your coffee store grind the sugar coated beans
• Steam portion: 14 seconds
Other settings: 3 to 120 seconds in 1 second intervals
• Language: English.
Other settings: French, Portuguese, German, Italian,
Dutch, Spanish
11.
Download from Www.Somanuals.com. All Manuals Search And Download.
and use as described in the ground coffee funnel (chapter 11).
Please note: If you like flavored coffees we recommend to add
flavors to your coffee after brewing. This way you can use your
regular coffee beans in the bean container. Adding the flavors
after brewing lets you control the intensity much better than with
pre-flavored coffee. Your local coffee store typically carries a
variety of flavors.
press one of the steam buttons (Fig. 3,M). SYSTEM FILLING.
The machine will dispense a little bit of water through the
steam nozzle. HEATING UP / PRESS RINSE.
• Place cup underneath the dual coffee spout (Fig. 8) and press
the RINSE button (Fig. 2,E). MACHINE RINSING. The
machine will dispense a little bit of hot water through the coffee
spout. SELECT PRODUCT.
Please note: You can only make coffee when the display reads
SELECT PRODUCT and the machine is not in programming mode.
• Open the Cover Lid (Fig. 5).
• Remove the Aroma Protection Lid (Fig. 6).
• Make sure the bean container is empty and clean. Fill beans
into the bean container (Fig. 7).
• Place a cup under the coffee spout and push one of the coffee
buttons. The machine will grind and brew coffee. If the display
shows FILL BEANS push one of the coffee buttons again.
• Discard the first two cups of coffee.
Frozen Beans: Thaw 3 to 4 hours before adding to bean
container. This prevents moisture from seeping into the grinder.
You are now ready to brew coffee.
Oily Beans: Beans with an oily surface tend to stick together.
This may prevent a continuous flow of beans from the bean
container into the burrs. As a result the grinder does not grind
enough coffee and you might get weak or no coffee at all.
Stir the beans in the bean container just before grinding.
Alternatively, you can also pour the beans in an open bowl and
let them sit for about 5 hours. The oils will evaporate (this will
not change the taste of your coffee). Then fill the beans into the
bean grinder. Now beans will feed into the burrs more easily.
CUP ILLUMINATION
The cup illumination adds a dramatic touch to brewing coffee.
Providing the machine is plugged in, you can activate the cup
illumination for 3 minutes by pressing any button.
7. ADJUSTING THE GRINDER
You can adjust the grinder to the roast of your coffee.
We recommend the following:
• Light roast: use a finer adjustment.
• Dark roast: use a coarser adjustment.
6c. TURNING THE MACHINE ON
• Press the Main Power Switch in the back of the machine (Fig. 1b) • Open the cover of the bean container (Fig. 5).
The On/Off button in the front will illuminate (Fig. 2,B)
• Push the On/Off button. The display shows FILL SYSTEM /
PRESS STEAM.
• To adjust grinding turn the selector switch to the desired
position (Fig.9).
You have the following possibilities:
• The smaller the dots, the finer the grinding.
• Place a container underneath the steam nozzle (Fig. 4) and
12.
Download from Www.Somanuals.com. All Manuals Search And Download.
• The bigger the dots, the coarser the grinding.
IMPORTANT: The grinding grade can only be adjusted while
the grinder is actually grinding.
ATTENTION: Oily beans tend to stick together. Stir beans just
before grinding to ensure a proper flow of beans into the burrs.
Please note: If coffee does not flow in a constant stream, turn
the grinder to a coarser setting.
• Place one or two cups underneath the Dual Coffee Spouts
and push the desired button. The machine will grind, tamp
and then brew the coffee. It uses a 2-step brewing process
(pre-brew phase), pauses for a few seconds, and then starts
the brewing process. The display will show the name of the
button you pushed, e.g. 1 ESPRESSO and the selected coffee
strength, e.g. STRONG.
Please note: when pushing any of the two-cup buttons, the cof-
fee strength is not displayed.
8. DAILY PREPARATION
We recommend filling the water container every morning with
fresh, cold water. This will enhance the taste of your coffee.
• Make sure the Main Power Switch is on (Fig. 1b). In this case
the On/Off button is illuminated.
• Push the On/Off button. The display shows HEATING UP.
After approx. 2 minutes the display shows PRESS RINSE.
• Push the Rinse Button (Fig. 2,E). Hot water will warm up all
internal parts and pump through the coffee spouts MACHINE
RINSING. The water will be caught in the drawer underneath.
The rinse cycle stops by itself and the display reads: SELECT
PRODUCT. You are now ready to make coffee.
Important: After the brewing stops the machine will discard the
used coffee grounds. Please do not try to pull out the drawer
(Fig.1,18) during this operation. It can seriously damage the
machine.There is no need to pull out the drawer until the display
shows the message EMPTY TRAY or EMPTY GROUNDS.
Please note: You can always stop the brewing process by
pressing any of the coffee buttons.
9a. OVERRIDING CUP SIZE
During brewing you can override the cup size for any of the four
coffee buttons as follows.
• When the coffee starts brewing, open the Cover for the
Rotary Dial (Fig. 1.19 ) and turn the Rotary Dial (Fig. 3A,P).
The display will show the cup size in oz. You can change the
coffee volume from 1 to 8 oz.
• When you push one of the double cup buttons, the display
shows the coffee volume per cup, e.g. if it shows 6 oz., the
machine will brew a total of 12 oz. of coffee.
Please note: Overriding the cup size will not change the pre-set
cup size. The next time you push one of the four buttons, it will
automatically brew the pre-set volume. See chapter 16 how to
change the pre-set values permanently.
Please note: Under normal use the machine will automatically
complete a rinse cycle when it is turned off (or when the
machine turns off automatically). If you have not brewed any
coffee at all the machine will not run a rinse cycle when turning off.
9. BREWING COFFEE AND ESPRESSO
The machine has four pre-set coffee buttons, 1 ESPRESSO,
2 ESPRESSI, 1 COFFEE, 2 COFFEES (Fig. 2).
All buttons are pre-set for coffee strength, coffee volume and
temperature.
13.
Download from Www.Somanuals.com. All Manuals Search And Download.
9b. THE A LA CARTE BUTTON
Frothing (Cappuccino): Injecting hot steam into the milk to warm
the milk and create a firm layer of tiny bubbles.
Steaming (Latte): Injecting hot steam to warm the milk without a
frothy layer.
The S Avantgarde has a fifth coffee button (Fig. 3A,N). With this
button you can change the coffee volume and the coffee
strength just before brewing.
• Push the A LA CARTE button. The display shows A LA
CARTE and the strengths,e.g. MILD.
10a. USING THE DUAL FROTHER PLUS
• Turn the Rotary Dial to choose any of five strength settings
(XMILD, MILD, NORMAL, STRONG, XSTRONG).
• Then push the Rotary Dial. The machine starts grinding. Now
you can dial the coffee volume
Please note: If you push the A LA CARTE button and you do
not push the Rotary Dial within a few seconds, the display will
revert to SELECT PRODUCT.
Frothing Position: The cylinder of the frother is pushed down.
Steaming Position: The cylinder is pushed up ( see Fig. 14).
• Fill at least 4 to 5 oz. of cold milk into a frothing pitcher. The
pitcher should have at least a 10 to 12 oz. capacity. You can
also use a larger pitcher (e.g. 20 oz.) and fill it with up to 13 oz.
of milk. (Normally 3 to 5 oz. of milk is what you need for one
cappuccino or one latte). Always start with cold milk. Skim
milk will produce the most froth and will let you taste more of
the coffee. Milk with 1% and 2% fat will give you a bit less froth.
Regular milk (3% fat) will produce even less froth.
The machine is ready to produce steam as long as both red
lights in the steam buttons are illuminated (Fig. 3,K & M).
• If they are off, just push either button. Both lights will start
blinking for about 15 to 30 seconds and then will stay
illuminated (chapter 16.6).
10. CAPPUCCINO AND LATTE
The Impressa S Series can be operated with two different froth-
ing systems:
a) The Dual Frother-PLUS which is mounted on all machines.
b) The frothXpress-PLUS system which is included with the S9
and S7 Avantgarde.
Recommendation:
• If you froth for only one or two cups at a time and want 100%
control over the frothing/steaming process, the Dual Frother-
PLUS might be the preferred equipment. Use with the
PERMANENT STEAM button (Fig. 3,M).
• If you always want the same amount of milk and milk froth in
your cup or you make three, four, five or more cappuccinos in
a row the frothXpress PLUS is definitely faster and more
convenient to use. Ideally use the STEAM PORTION button
(Fig. 3,K).
• Immerse the frother into the milk so that the tip and part of the
cylinder are below the surface of the milk. The tip of the
frother should not touch the bottom of the pitcher.
• Now push the PERMANENT STEAM button (Fig. 3,M). Hot
steam will be injected into the milk. The display will read
DRAW OFF STEAM.
• To stop the steam output, push either steam button again.
The display shows SELECT PRODUCT.
14.
Download from Www.Somanuals.com. All Manuals Search And Download.
Please note: The tip of the dual frother should be attached
finger tight to the rod (Fig. 14b). The top of the rod is flexible.
Make sure the rod is properly seated over the steam nozzle,
touching the chrome cover (Fig. 4).
steam button. Steam will eject any milk droplets. To stop,
push the steam button again after one or two seconds.
Tip: if the steam nozzle is blocked by hardened milk, use a needle
and loosen up the milk deposit. Then let some steam pass
through the steam nozzle.
Tips for steaming: Leave the sleeve in the "up" position
(Fig. 14). Make sure that the milk does not start boiling. You can
stop the steaming process at any time by pushing either steam
button. To continue steaming, push either steam button again.
Tips for frothing: Start with the frother in the steaming position
("up") for 10 to 20 seconds, depending how much milk you are
working with. This way the milk is first heated. Then push down
the cylinder. The sound will change and milk-froth will build up
immediately. This way the froth on top of your milk is also warm.
If the milk is not warm enough, continue in the steaming position.
Attention: When moving the sleeve of the Dual Frother up and
down, avoid touching the metal parts since they become hot
during operation.
10c. USING THE FROTHXPRESS PLUS SYSTEM
WITH MILK CONTAINER
The frothXpress system lets you produce hot steamed or frothed
milk right into your cup. After playing a bit with this attachment
you will be able to get exactly the amount of frothed or steamed
milk you want in your cup (refer to the video).
• Remove the Dual-Frother-PLUS.
• Fill the milk container with cold milk.
• Assemble the milk container as shown in Fig. 15.
• Attach the frothXpress-PLUS system as shown in Fig. 15a.
Important: This system siphons milk and mixes it inside the
frothXpress with hot steam. It is necessary that all parts are con-
nected tightly, otherwise the siphoning process will not work.
Frothing Position: The dial points to the upper part of the face
(frothing range). Start with the dial pointing to the "-" symbol (12
o'clock). Milk will be siphoned, heated and frothed. For hotter
milk, move the lever towards the "+" symbol (See Fig. 15).
Steaming Position: The dial points to the lower part of the face
(steaming range). Start with the dial pointing to the "-" symbol (6
o'clock). Milk will be siphoned and heated with no froth. For hotter
milk move the lever towards the "+" symbol.
10b. CLEANING THE DUAL FROTHER PLUS
The tip and sleeve of the frother are high precision parts (Fig. 14b).
Always keep those parts clean and free of any milk residue.
Make sure that all openings and grooves in the tip are free of
any milk deposits.
• After finishing frothing, remove the Dual Frother Plus and
immerse it in a cup with warm water. This is the easiest way to
keep the milk from hardening. When replacing the frother
push it up and make sure it covers the steam nozzle com-
pletely (Fig. 4, Fig. 14b)
Steam Only Position: When the dial points to the steam symbol
(3 o'clock), the siphoning is blocked. Only steam will pass
through the frother Fig. 16.
Cleaning the steam nozzle: The Dual Frother PLUS is off (Fig. 4).
• Place a cup underneath the steam nozzle and press the
15.
Download from Www.Somanuals.com. All Manuals Search And Download.
Frothing
TIP: After filling your cup(s) with the desired amount of hot
frothed milk you can immediately move it (them) underneath the
coffee spouts and brew coffee.
• Place a cup underneath the frothXpress (see Fig. 15a). The
machine is ready to produce steam as long as both green
lights in the steam buttons are illuminated. If they are off, just
push either button. Both lights will start blinking for about 15
seconds and then will stay illuminated.
• Make sure that the dial points to the 12 o'clock position.
• Press the PERMANENT steam button. The display will read
STEAM INTAKE and frothing will begin immediately.
• When you have enough frothed milk push the button again.
Frothing will stop.
If you always use the same amount of frothed/steamed milk, you
can use the STEAM PORTION button (Fig. 3,K). Steam will be
dispensed for the programmed time and then it will stop auto-
matically. During this time the display shows STEAM PORTION.
The factory setting is for 14 seconds of steaming. You can pro-
gram the steam portion button to froth from 3 to 250 seconds
(see chapter 15.4).
10d. USING THE FROTHXPRESS PLUS SYSTEM
WITH FLEXIBLE HOSE (Fig. 17)
The machine comes equipped with a long flexible hose. This is
useful if you have your regular milk in the milk container and you
want to use another milk or chocolate milk.
• Insert the black connecting piece into the frothXpress system.
Insert the other side of the flexible hose into a milk carton.
• Now froth or steam as described in chapter 10c.
10e. HOT CHOCOLATE, CAFE MOCHA
For hot chocolate fill the milk container with the desired amount
of chocolate syrup, add cold milk and stir well. Then proceed as
described under "Frothing". Adding a shot or two of espresso
makes it a Café Mocha.
Hotter Milk
• If you want your frothed milk hotter, move the dial to the
middle position (3 o'clock).
• Lift the cup so that the bottom of the frother is slightly
immersed into the milk. Push the PERMANENT steam button.
Hot steam will increase the milk temperature. Push the button
again to stop.
10f. CLEANING THE FROTHXPRESS PLUS
• Remove the hose which connects the frothXpress Plus and
the milk container.
• Store the milk container in the refrigerator.
• Remove the frothXpress from the steam nozzle.
• Drop the hose and the frothXpress in a cup with warm water.
This will prevent the milk from hardening.
Steaming
• Place a cup underneath the steam nozzle and push the
PERMANENT steam button and let steam pass through for a
second or two (see Fig. 4).
Setting the dial to the lower part of the face, will eliminate any
froth build up. Milk will be siphoned and warmed. Otherwise it is
the same procedure as explained above under "Frothing".
• Replace the frothXpress-PLUS system.
16.
Download from Www.Somanuals.com. All Manuals Search And Download.
FILL POWDER/SELECT PRODUCT.
• Fill 1 or 2 level measuring scoops of ground coffee into the
opening for ground coffee (Fig. 1,11).
• Now push one of the four coffee buttons to brew your coffee.
Please note: If the GROUND COFFEE button (Fig. 3A,O) is
pressed by mistake just press one of the coffee buttons NOT
ENOUGH POWDER. The machine will automatically stop brewing
and return to SELECT PRODUCT.
Please note: After use of sugar coated or flavored coffee
through the pre-ground coffee funnel you may experience some
flavor transfer when switching back to your regular coffee. Select
the function RINSE in Programming and a manual rinse cycle
(chapter 17.1).
For a more thorough cleaning you can take the pieces apart.
When attaching the chrome sleeve to the black nipple, angle it
as shown above. Use a twisting back and forth motion and
gently push the two pieces together.
10g. CLEANING THE MILK CONTAINER
• Remove the lid of the milk container. (The milk container is
dishwasher safe; upper rack.)
12. USING HOT WATER
• Place a cup under the height-adjustable coffee spout
(Fig. 8a or 8b) and turn selector switch to the right (Fig. 3,L)
to the water symbol. Hot water will come out of the hot water
spout (Fig.1,14). During this time the display shows:
WATER PORTION. After 5 oz. of hot water (factory setting) the
flow will stop automatically. The display shows: CLOSE TAP.
• Turn the selector switch back to the coffee symbol (Fig. 3,L)
SELECT PRODUCT. To change the programmed amount of
hot water (chapter 16.4).
• Clean the lid and the two metal hoses with warm water.
• Assemble as shown in Fig. 15.
11. USING GROUND COFFEE
You can also use pre-ground coffee, bypassing the grinder. This
comes in handy if someone requests decaf coffee or a decaf
cappuccino. You can also use the pre-ground funnel for ground
flavored coffee.
Please note: Never fill the funnel with instant coffee. Do not fill
the funnel with more than two scoops. The funnel is not a
storage container. If coffee is ground too fine it might be processed
very slowly or the machine will interrupt the process altogether.
• Open cover (Fig. 1,19).
13. WATER CARE
Water is heated inside the machine. With use, this leads to calci-
um deposits forming inside the machine. You have the following
options to take care of the water:
• Press the GROUND COFFEE button (Fig. 3A,O).
Most convenient: Clearyl Water Filter Cartridge (chapter 14).
17.
Download from Www.Somanuals.com. All Manuals Search And Download.
Least expensive: Decalcifying System (chapter 18.2, 18.3).
Your machine is pre-set in the factory to automatically remind
you to decalcify based on a water hardness of Level 2. You can
change the water hardness setting to comply with the water you
are using (chapter 15a).
• Remove the water tank, make sure it is empty.
• Pull up the cartridge holder and insert the cartridge with its
tapered end down into the water container (Fig. 12, Fig. 13).
Make sure it fits securely inside the fins. Push down gently
(Fig. 13).
Please note: The machine will automatically remind you when it
is necessary to run certain water maintenance programs. It is
important that you follow those instructions. Otherwise your
machine might break down.
• Close the cartridge holder. Make sure the holder snaps into
place.
• Fill the water tank with fresh cold water and replace.
Activating:
14. CLEARYL WATER FILTER CARTRIDGE
The machine comes with one Clearyl Water Filter Cartridge. The
Clearyl cartridge
• Reduces the water hardness up to 75%.
• Removes (if present) up to 85% chlorine, up to 90% lead, up
to 95% copper and up to 67% aluminum.
You must activate the cartridge otherwise the machine cannot
monitor it properly and assumes that the machine is still in
decalcifying mode.
SELECT PRODUCT
1.Push the Rotary Dial until you hear a beep. The display shows
FILTER NO
• Cleans the water through an upward current principle (Fig. 9)
just before the brewing cycle starts, ensuring freshly filtered
water every time you make coffee.
• Eliminates decalcifying except when using very hard water
(25 grains or higher), see chapter 15. In this case we recom-
mended to decalcify the machine once or twice a year.
• To reorder cartridges, see chapter 21.
2.Push the Rotary Dial again, to enter the FILTER function.
3.Turn the Rotary Dial until the display shows FILTER YES and
push the Rotary Dial to confirm. The display shows INSERT
FILTER/PRESS STEAM.
4.Place a 20 oz. container under the Steam Nozzle (Fig. 4) and
push either steam button (Fig. 3, K or M). The display shows
FILTER RINSING. For the next 60 seconds the machine will
push water through the cartridge and out through the steam
nozzle. Initially, the water may have a slight discoloration. The
program will stop automatically. The display shows SELECT
PRODUCT.
14a. INSTALLING & ACTIVATING THE CLEARYL WATER
CARTRIDGE
Installing:
Important: Never install the cartridge before or during
"Preparing Machine For The First Time" (chapter 6).
Please note: As long as the filter is activated, the water
• Remove cartridge from its bag and rinse cartridge under water. hardness setting is automatically turned off.
• Add the extension rod to the cartridge (Fig. 11).
18.
Download from Www.Somanuals.com. All Manuals Search And Download.
14b. REPLACING THE CLEARYL WATER CARTRIDGE
The filter is monitored automatically. After approx. 75 liters of
water (~2,500 oz.) the display shows SELECT PRODUCT /
CHANGE FILTER. The Rinse Button will light up.
Important: Once the filter has lost its calcium suppressing
abilities, calcium will build up inside the machine. Since the
Water Hardness Selector is off, the machine will not remind you
when to decalcify. This could clog and ruin your machine.
• Push the Rinse Button. INSERT FILTER/PRESS STEAM.
• Remove the water tank and the old filter and set the extension
rod aside. The used filter cartridge is environmentally friendly
and can be disposed with your regular household trash.
Important: Keep the Extension Rod
for the "Water Hardness in Grains." The machine will show you
the water hardness in the German hardness scale (which is a bit
different from the American "Grain" scale (see chart below).
You can also use the enclosed water hardness indicator strip to
determine the water hardness:
• Insert the stick for one second into the water you want to
use. Shake off any access water and wait for one minute.
• If all five fields of the test stick turn reddish, set the hardness
level to 5 squares. If four fields turn reddish, set the hardness
level to 4 squares and so on.
Please note: If you use Spring Water or Bottled Water you can
set the hardness level to 1, "extremely soft water".
• Make sure the water tank is empty.
The machine will give you the following options:
• Remove the new cartridge from its bag and rinse under
running water. Now install as explained in chapter 14A.
• Place a 20 oz. container under the Steam Nozzle (Fig. 4).
• Push either steam button. The display shows FILTER RINSING
For the next 90 seconds the machine will push water through
the cartridge and out through the steam nozzle. Initially, the
water may have a slight discoloration. The program will stop
automatically. The display shows SELECT PRODUCT.
Display Equivalent Indicator Strip
German American number of
Level
Display
Degree Grains
"reddish" fields
Not Active*
1. extremely soft water
2. soft water
3. medium water
4. hard water
5. very hard water
6. extremely hard water
No Display
—
1-4
5-9
—
1-5
6-11
—
None
1 to 2
10-14 13-18 2 to 3
15-19 19-24 3 to 4
20-24 25-30 4 to 5
25-30 32-38 All 5
15. WATER HARDNESS MONITOR
If you do not use the Clearyl Filter Cartridge (chapters 14 – 14b.)
the machine will remind you when it is time to perform a decalci-
fying cycle. The machine is set to medium hard water. If you
have harder water you need to set it to a higher level. If you have
softer water you can set it to a lower level. If you are not sure
about the hardness of your water, ask your local water company
*Not Active: You can only use this setting for distilled water.
Level 5 and Level 6: If your tap water is very hard and falls into
these two categories, decalcifying will be frequent. In this case
bottled water is recommended.
19.
Download from Www.Somanuals.com. All Manuals Search And Download.
Please note: If your water has a high calcium content (level 5 or 6)
and you use the Clearyl Filter Cartridge we recommend to decalcify
the machine once or twice a year (chapter 18.2).
Function
Display
Comment
Chapter
Clearyl Water
Filter
FILTER NO or
FILTER YES
Install and activate the
Clearyl Filter
14-
14b
15a. CHANGING THE WATER HARDNESS MONITOR
SELECT PRODUCT
• Push the Rotary Dial until you hear a beep. Display shows
FILTER NO
• Turn the Rotary Dial until the display shows
HARDNESS 10º DH
Water Hardness
(if FILTER is set to
YES, this function
is suppressed)
HARDNESS
Change water hardness
(when not using the
Clearyl Filter)
15-
15a
• Push the Rotary Dial to enter the program.
• Turn the Rotary Dial until desired hardness level is displayed.
• Push the Rotary Dial to confirm the setting.
• Turn the Rotary Dial until the display shows EXIT.
• Push the Rotary Dial. The display shows
SELECT PRODUCT
Cleaning and
Rinsing Programs
RINSE
Activate maintenance
programs outside the
automatic prompts
17.1
Coffee Strength
Coffee Volume
Temperature
POWDER
QUANTITY
Choose for each of the four 16.1
coffee buttons from five
different strength settings
The machine will automatically remind you when it is time to
decalcify (chapter 18.2).
16. PROGRAMMING
WATER
QUANTITY
Choose for each of the five
coffee buttons the cup size
(1 oz. to 8 oz. per cup)
16.2
16.3
The S Avantgarde Series provides programming, maintenance
and look-up functions. With the display at SELECT PRODUCT
you can access these functions as follows:
• Push and hold the Rotary Dial until you hear a beep and the
display shows FILTER.
The machine offers the following Functions (see chart).
• Slowly turn the dial clockwise to scroll through Functions.
Please note: to get back to SELECT PRODUCT, turn the Rotary
Dial until the display shows EXIT, then push the Rotary Dial.
TEMP
Choose for each of the
five coffee buttons from
two temperature settings
Hot Water
Volume
WATER
PORTION
Choose the amount of hot
water for the hot water
spout (from 1 oz. to 15 oz.)
16.4
20.
Chapter
Download from Www.Somanuals.com. All Manuals Search And Download.
16.1 COFFEE STRENGTH / POWDER QUANTITY
You can set the coffee strength for the 1-cup espresso and the
1-cup coffee button to XMILD, MILD, NORMAL, STRONG or
XSTRONG. In XMILD coffee is ground for about 41⁄2 seconds, in
XSTRONG for about 91⁄2 seconds. The double cup buttons grind
from approx. 7 seconds to the maximum of 91⁄2 seconds. The
overall amount of ground coffee is further determined by the
fineness setting of the grinder (see chapter 7). The coarser you
grind, the more coffee will be disbursed into the brewing cham-
ber. The maximum amount of ground coffee is about 16 grams.
The minimum amount is about 5 grams.
Function
Display
Comment
Chapter
Steam Duration
DRAW OFF
STEAM
Choose the duration for
the steam portion button
from 3 to 120 seconds
16.5
Economy Mode
ECONOMY
Choose from three
power saving modes
Comment
16.6
Function
Actual Time
Display
TIME
Chapter
Set actual time
16.7
Auto-On
Auto-Off
UNIT ON
Choose an auto-on time
16.8
16.9
SELECT PRODUCT
• Push and hold the Dial. FILTER
OFF AFTER
Choose an auto-off time
after last use
• Turn the Dial until the display shows POWDER QUANTITY.
• Push the Dial. The display shows SELECT PRODUCT.
• Push either the 1-cup espresso or 1-cup coffee button.
• Turn the dial until the desired setting is shown in the display.
• Push the dial to confirm. A 3-tone melody confirms the new
setting. POWDER QUANTITY. To select another coffee button,
push the dial again and repeat the steps above. Or you can
turn the Dial to EXIT.
Language
Display
LANGUAGE
DISPLAY
Change the display to
another language
16.10
16.11
Choose cup size info. in
OZ. to ML. Choose time
display in 24HRS or
AM/PM mode
• Push the Dial to get back to SELECT PRODUCT.
Information
INFO
Check how often certain
functions are used
16.12
16.2 COFFEE VOLUME (CUP SIZE) / WATER QUANTITY
You can program all five coffee buttons individually to brew
between 1 and 8 oz. of coffee per cup.
Please note: the display will always show the amount per cup.
SELECT PRODUCT
Exit programming EXIT
The only way to get back
to SELECT PRODUCT
• Push and hold the Dial. FILTER
• Turn the Dial until the display shows WATER QUANTITY.
21.
Download from Www.Somanuals.com. All Manuals Search And Download.
• Push the Dial. The display shows SELECT PRODUCT.
• Push for example the 2-cup espresso button. Turn the dial
and select 3 OZ.
• Push the Dial to get back to SELECT PRODUCT.
16.4 HOT WATER VOLUME / WATER PORTION
• Push the dial to confirm. The 3-tone melody confirms the new
setting. From now on, the 2-cup espresso button will produce
a total of 6 oz. of coffee. WATER QUANTITY. To select another
You can program the hot water spout to dispense between 1
and 15 oz. of water and then stop. This is useful if you use the
hot water spout to make an 8 oz. cup of tea.
coffee button, push the Dial again and repeat the steps above. Please note: when using the hot water function, you can always
Or you can turn the Dial to EXIT.
stop the flow of hot water simply by turning the hot water dial
• Push the Dial to get back to SELECT PRODUCT.
back to the coffee position.
SELECT PRODUCT
16.3 TEMPERATURE / TEMP
• Push and hold the Dial. FILTER
You can program all five coffee buttons individually to brew at
temperature NORMAL or HIGH. In HIGH the coffee is approx.
7º F higher than in NORMAL.
Please note: The temperature is also influenced by the resist-
ance of the coffee. Finer ground coffee and more coffee in the
brewing chamber will result in more resistance, increasing the
temperature of your coffee. Also, the first cup of coffee is always
slightly less hot than subsequent coffees.
• Turn the Dial until the display shows WATER PORTION.
• Push the Dial. The Display shows PORTION 5.0 OZ.
• Turn the dial to change the hot water volume from 1 to 15 oz.
• Push the dial to confirm. The 3-tone melody confirms the new
setting. WATER PORTION.
• Turn the Dial to EXIT.
• Push the Dial to get back to SELECT PRODUCT.
SELECT PRODUCT
16.5 STEAM DURATION / STEAM PORTION
• Push and hold the Dial. FILTER
When using the frothXpress Plus system, you can set the
amount of hot steamed or frothed milk to a certain volume by
using the Steam Portion button (Fig. 3,K). By selecting a certain
steaming time the machine will always siphon, steam and froth
the same amount of milk and then stop automatically. You can
set the steam time between 3 and 120 seconds.
• Turn the Dial until the display shows TEMP.
• Push the Dial. The Display shows SELECT PRODUCT.
• Push for example the 1-cup coffee button. HIGH.
• Turn the dial and select NORMAL.
• Push the dial to confirm. The 3-tone melody confirms the new
setting. From now on, the 1-cup coffee button will use the
Please note: you can always stop the steam action by simply
NORMAL temperature setting. TEMP. To select another coffee pushing either steam button. Push either steam button again
button, push the dial again and repeat the steps above.
and steaming will continue.
Or you can turn the Dial to EXIT.
SELECT PRODUCT
22.
Download from Www.Somanuals.com. All Manuals Search And Download.
• Push and hold the Dial. FILTER
Choose this setting if you prepare only a few coffees or cappuc-
cinos in large intervals. It is much faster than turning the
machine on and off every time you want to make coffee.
Five minutes after last use (coffee or steam), the machine will
lower the temperature of the thermoblock for coffee. When
making coffee at a later time, the machine will first heat up. This
will take between 5 and 30 seconds.
• Turn the Dial until the display shows STEAM PORTION.
• Push the Dial. Display shows (example) PORTION 14 SEC.
• Turn the dial to change the steam time to the desired setting.
• Push the dial to confirm. The 3-tone melody confirms the
new setting. STEAM PORTION.
• Turn the Dial to EXIT.
• Push the Dial to get back to SELECT PRODUCT.
SELECT PRODUCT
• Push and hold the Dial. FILTER
16.6 ECONOMY MODES / ECONOMY
You can set the machine to three different modes.
ECONOMY MODE –
• Turn the Dial until the display shows ECONOMY MODE - .
• Push the Dial and turn to the desired setting e.g. ECONOMY
MODE 1.
The machine is always ready to brew coffee and to produce
steam. The two red indicator lights in the steam buttons are
always on.
• Push the dial to confirm. The 3-tone melody confirms the
new setting. The display will show the new setting,
ECONOMY MODE 1.
ECONOMY MODE 1
Turn the Dial to EXIT.
The machine is always ready to brew coffee and is in the
Push the Dial to get back to SELECT PRODUCT .
energy saving mode for steam.
If the machine is mostly used for coffee this setting will consume 16.7 ACTUAL TIME / TIME
less energy. The heating element for steam will shut off after
approx. 10 minutes after last use. At this time the two red indi-
cator lights in the steam buttons will turn off. If you want to use
the steam function, push one of the steam buttons. The lights
will start blinking, indicating that the thermoblock for steam is
heating up. This will take between 5 and 30 seconds depending
how much the thermoblock was cooled down. Once the red
indicator lights in the steam buttons are illuminated, you can
push them again and steam will be produced.
Setting the time allows you to program an auto-on time.
SELECT PRODUCT
Push and hold the Rotary Dial. FILTER
Turn the Dial until the display shows TIME -.-
• Push the Dial and turn the Dial to set the hours.
• Push the Dial to confirm.
• Now turn the Dial to set the minutes.
• Push the Dial to confirm. TIME 7:15 AM (example).
The 3-tone melody confirms the new setting.
• Turn the Dial to EXIT.
ECONOMY MODE 2
This setting will save more energy than economy mode 1.
• Push the Dial to get back to SELECT PRODUCT.
23.
Download from Www.Somanuals.com. All Manuals Search And Download.
16.8 AUTO-ON / UNIT ON
Recommendations: If you use the machine only in the morning,
You can set a time at which the machine turns itself on. This way change the auto-off to 2 hours. If you use the machine all day
you don’t have to wait for the machine to warm up. Just run one
10 second rinse cycle and you can have your first cup of coffee.
Please note: Auto-on will only work if you set the actual time
long,leave the auto/off as is. This way the machine is always
ready and you don’t have to turn it on and wait for it to warm up
again.
and the main power switch is turned on (when the small red light SELECT PRODUCT
in the On/Off switch is illuminated, you know that the main
• Push and hold the Dial. FILTER
power is on).
SELECT PRODUCT
• Push and hold the Dial. FILTER
• Turn the Dial until the display shows UNIT ON -.-
• Push the Dial.
• Turn the Dial until the display shows OFF AFTER.
• Push and turn the Dial until the desired setting appears.
• Push the Dial to confirm. The 3-tone melody confirms the new
setting. (example) OFF AFTER 2 HRS.
• Turn the Dial to EXIT.
• Turn the dial to set the hours and push the Dial to confirm.
• Turn the Dial to set the minutes and push the dial to confirm.
The 3-tone melody confirms the new setting. (example)
UNIT ON 6:45 AM .
• Push the Dial to get back to SELECT PRODUCT.
16.10 LANGUAGE / LANGUAGE
You can change the display from English to French, Portuguese,
• Turn the Dial to EXIT.
German, Italian, Dutch or Spanish.
• Push the Dial to get back to SELECT PRODUCT.
Please note: If you turn the machine off with the main power
switch (Fig. 1b) or if you unplug the machine or experience a
power outage, the actual time will not be retained. The next time
you turn the machine on, the display will first show TIME --.--.
Turn the Rotary dial to set the hours, then push the Rotary dial,
Turn the Rotary dial again to set the minutes and push to con-
firm. Now the AUTO-ON time will be automatically restored.
SELECT PRODUCT
• Push and hold the Dial. FILTER
• Turn the Dial until the display shows LANGUAGE.
• Push and turn the Dial until the desired language appears. The
3-tone melody confirms the new setting.
• Turn the Dial to EXIT (in the language you choose)
• Push the Dial to get back to SELECT PRODUCT (in the
language you choose).
16.9 AUTO-OFF / OFF AFTER
16.11 DISPLAY / DISPLAY
Your machine is pre-set to turn itself off 5 hours after last use.
This function lets you select the time format AM/PM or 24HR
You change the auto-off interval between 1⁄2 hour and 14 hours or format and the volume either in ounces OZ or milliliters ML.
you can set the machine not to turn off itself at all.
SELECT PRODUCT
24.
Download from Www.Somanuals.com. All Manuals Search And Download.
• Push and hold the Dial. FILTER
PRESS RINSE
• Turn the Dial until the display shows DISPLAY AM/PM / OZ.
• Push and turn the Dial to change the time display and push
the dial to confirm.
You must push the Rinse button (Fig. 2,E). The machine will
pump hot water through the coffee spouts.
FILL SYSTEM
• Then turn the Dial again to change from OZ to ML and push
to confirm. The 3-tone melody confirms the new setting.
24HRS / ML (example).
Place a cup underneath the steam nozzle and push one of the
steam buttons. The machine will dispense a little bit of water.
(chapter 6c.)
• Turn the Dial to EXIT.
FILL WATER
• Push the Dial to get back to SELECT PRODUCT.
The water tank is almost empty. You must add water before you
can resume brewing coffee.
16.12 INFORMATION / INFO
EMPTY GROUNDS or EMPTY TRAY
Check how often you used these eleven functions: 1- and 2- cup The used coffee container is full (it holds a maximum of 16
espresso and coffee buttons, A La Carte button, Ground Coffee
POWDER, hot water WATER, Steam, tablet cleaning CLEAN-
ING, decalcifying DE-SCALE and Clearyl Filter FILTER.
SELECT PRODUCT
coffee portions). You must empty the coffee container before you
can resume brewing coffee.
Make sure the coffee spout is moved upwards. Carefully lift and
pull out the removable drawer (Fig. 18). TRAY MISSING. There
is water in the drawer. Empty the drawer and the used coffee
container, assemble and replace. Make sure that that the two
metal contacts of the drawer are clean and dry.
Please note: If don’t plan on using the machine for a few days,
we recommend, pulling out the tray and emptying the used cof-
fee container. Used, moist coffee grounds will develop mold and
mildew.
• Push and hold the Dial. FILTER
• Turn the Dial until the display shows INFO.
• Push the Dial. (example) 1 ESPRESSO 50 .
• Turn the dial to check the frequency of the other usages.
• Push the Dial. INFO.
• Turn the Dial to EXIT.
• Push the Dial to get back to SELECT PRODUCT.
Important: If you pull out the drawer without any corresponding
message in the display you must empty the used coffee container.
The machine assumes that it will be emptied. If you do not empty
the container, used coffee will overflow inside the machine and
cause serious damage to the coffee release mechanism.
Please note: the machine does not sense if the used coffee
container is inserted (Fig. 1,16) If you forget to place the used
17. CARE AND MAINTENANCE MESSAGES
The machine will automatically display messages. In some cases
the message allows you to continue to brew coffee. In other
cases no further coffee brewing is possible before the task has
been completed.
25.
Download from Www.Somanuals.com. All Manuals Search And Download.
coffee container onto the drawer, ground coffee will discharged
onto the drawer.
TRAY MISSING
Insert the drawer complete with the empty used coffee container.
FILL BEANS
17.1 MANUAL MAINTENANCE CYCLES (RINSE)
The programming function RINSE lets you access the following
maintenance programs, even if the machine does not prompt you:
RINSE MACHINE, CLEAN MACHINE (Tablet Cleaning),
DE-SCALE MACHINE, CHANGE FILTER.
You must refill the bean container before you can brew coffee
again. You can still dispense hot water or use the steam function.
SELECT PRODUCT / CLEAN MACHINE
After approx. 220 coffee brewings or 80 rinsing cycles you must
run a tablet cleaning cycle. You can still make coffee, however
we highly recommend to perform the cleaning cycle within the
next few days (chapter 18).
Please note:
• DE-SCALE MACHINE is not accessible if you are using the
Clearyl Water filter and the function FILTER is set to YES.
• CHANGE FILTER is not accessible if the function FILTER is
set to NO.
RINSE MACHINE
SELECT PRODUCT / CLEAN NOW
After another 30 coffee brewings the message CLEAN
MACHINE changes to CLEAN NOW.
This program is useful if you used flavored coffee in connection
with the pre-ground coffee button. One or two extra rinse cycles
will remove any flavor transfer before brewing you next cup of
flavor free coffee.
SELECT PRODUCT / DE-SCALE MACHINE
It is time to decalcify the machine. You can still make coffee,
however we highly recommend to perform the decalcifying cycle
within the next few days.
Please note: this message should not appear if you use the
Clearyl Filter Cartridge. If you use the cartridge and the message
appears, then your cartridge function was not activated. Follow
the instruction in chapter 14a to program and activate the
Cartridge function. If the cartridge is already in use for several
weeks install a new cartridge.
SELECT PRODUCT.
• Push and hold the Rotary Dial. FILTER.
• Turn the Rotary Dial until the display shows RINSE.
• Push the Rotary Dial and select RINSE MACHINE.
• Push the Rotary Dial. The machine will run a rinse cycle
through the coffee spouts and will automatically return to
SELECT PRODUCT.
CLEAN MACHINE (tablet cleaning)
DE-SCALE NOW
It is really time to decalcify the machine. Don’t wait any longer.
SELECT PRODUCT / CHANGE FILTER
This program is useful if excessive oil build-up inside the
machine slows the brewing process down.
SELECT PRODUCT.
It is time to replace the Clearyl filter.
• Push and hold the Rotary Dial. FILTER.
• Turn the Rotary Dial until the display shows RINSE.
26.
Download from Www.Somanuals.com. All Manuals Search And Download.
• Push the Rotary Dial and select CLEAN MACHINE.
• Push the Rotary Dial.
push the grinder shield upwards (Fig. 24) Do not try to
remove the shield completely.
• Then follow the instructions in chapter 18.1.
• If any beans remain, remove them.
• Attach the burr grinder release tool to the upper burr (Fig. 25).
• If you cannot find this tool call 1-800-220-5701 and we will
send the tool to you free of charge.
• Turn the tool counter-clockwise slowly until the stone
becomes loose.
DE-SCALE MACHINE.
• To access this program set the function FILTER to NO.
• Then select within the function RINSE, the program
DE-SCALE MACHINE.
• Push the Rotary Dial. Follow the instructions in chapter 18.3
Attention: Do not try to turn the tool clockwise.
• Fold the shield down and replace the screw.
• Turn machine on and test the grinder without beans to see
if the blockage has disappeared.
CHANGE FILTER.
When you use the Clearyl filter and the machine does not auto-
matically remind you within three months to change it, the filter
needs to be replaced with this program. To access this program
manually, make sure the function FILTER is set to YES.
SELECT PRODUCT.
17.3 GENERAL CLEANING INSTRUCTIONS
Never use abrasive materials or chemicals to clean the
machine.
• Push and hold the Rotary Dial. FILTER YES.
• Turn the Rotary Dial until the display shows RINSE.
• Push the Rotary Dial and select CHANGE FILTER.
• Push the Rotary Dial.
• Clean the housing with a soft, damp cloth.
• Rinse water tank daily and fill with fresh cold water.
17.4 EMPTYING THE SYSTEM BEFORE TRANSPORT
This procedure is necessary to prevent water and frost damage
in case you intend to transport the machine.
SELECT PRODUCT
• Remove the frother system. Leave the steam nozzle
attached (Fig. 4).
• Place a container under the steam nozzle.
• Turn the machine off. The main power switch is still on.
• Press and hold either steam button until the display shows
SYSTEM EMPTYING
• Then follow the instructions in chapter 14b.
17.2 REMOVING STONES FROM THE BURR GRINDER
If the burr grinder is blocked, proceed as follows:
• Turn off the machine by pushing the ON/OFF button (Fig. 2,B).
Wait until the machine has shut down completely.
• Turn the main power switch off (Fig 1b).
• Open the bean container lid and remove all beans (scoop out
beans or use a hand-held vacuum cleaner).
• Remove the screw in the bean container (Fig. 23) and
27.
Download from Www.Somanuals.com. All Manuals Search And Download.
• When the process is completed the machine turns itself off.
Next time you turn the machine on the display will show
FILL SYSTEM/PRESS STEAM (chapter 6c).
4. Place a large container (24 oz.) underneath the
coffee spout (Fig. 8b) and push the Rinse button (Fig. 2.E).
The display will show MACHINE CLEANING. After a short
while you will hear a beep and the display shows
18. AUTOMATIC CLEANING CYCLES
ADD TABLET/PRESS RINSE
5. Open the ground coffee funnel lid and drop one white tablet
into the opening (Fig. 22).
18.1 CLEANING WITH SPECIAL TABLET
The machine monitors how many coffees are brewed and how
often the rinsing program is activated. After approx. 220 coffees
the display will show CLEAN MACHINE. You can continue to
make coffee, however we highly recommend that you clean the
machine as described below within the next few days. This
cleaning program will remove oil build-ups in the brewing chamber.
If the display shows CLEAN NOW you should clean the machine
immediately. There will also be a "beep".
6. Push the Rinse button. The display shows
MACHINE CLEANING. The machine will start the automatic
cleaning program by dispensing water in intervals into the
container underneath the coffee spout. When finished, the
display shows EMPTY TRAY/EMPTY GROUNDS and the
machine "beeps".
7. Remove the tray. There will be water in the tray and in the
used coffee container. Empty, clean and replace. The display
shows SELECT PRODUCT.
This cleaning program takes about 15 minutes. Please use the
enclosed white cleaning tablet. The machine comes with a pack
of 2 tablets. To re-order see chapter 21.
Important: Once the cleaning program has started do not
interrupt the procedure.
8. Clean the ground coffee funnel.
9. Remove the funnel and rinse under hot water and dry.
Replace funnel (Fig. 20 and 21).
18.2 DECALCIFYING
SELECT PRODUCT/CLEAN MACHINE
The machine has an integrated decalcifying program.
1. Push and hold the Rinse button until the following message
This program takes less than 50 minutes.
appears
.
When the display shows DE-SCALE MACHINE it is time to
decalcify the machine. You can still make coffee. However, it is
highly recommended that you decalcify the machine within the
next 3 to 4 days.
EMPTY TRAY/EMPTY GROUNDS
2. Make sure that the water container is at least half full.
3. Remove and empty the tray and the used coffee container
and replace.
Attention: If the tray and the used coffee container are
already empty, you still need to remove the tray for approx.
20 seconds and then replace it. PRESS RINSE
Please note: If you use the Clearyl water cartridge and the display
shows DE-SCALE MACHINE then your cartridge function is not
activated. Follow the instructions in chapter 14a to activate the
28.
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearyl Cartridge. If the cartridge is in use for several weeks install 6. Push either steam button. The display shows MACHINE
a new cartridge.
DE-SCALING. The lights in the Steam buttons start blinking.
The machine will pump the mixture in intervals through the
steam nozzle into the container underneath. After 10 minutes
the machine "beeps". The display shows OPEN TAP.
7. Empty the container underneath the steam nozzle and
place it underneath the hot water spout (Fig.1,14).
8. Turn the Selector switch to the hot water position (Fig. 3,L).
The machine will now pump the mixture in intervals through
the hot water spout. MACHINE DE-SCALING.
Important: The decalcifying program must not be interrupted.
DECALCIFYING AGENT: Only use our special decalcifying
tablets Model # 61848, see chapter 21.
CAUTION: Never use vinegar or any other decalcifying agent.
This might damage internal parts of the machine.
CAUTION: Immediately remove any splashes or drops of the
decalcifying solution from sensitive surfaces, such as natural
stone or wood.
9. After approximately six minutes the machine will beep
Always wait until the decalcifying solution in the water tank has
been used up. Do not fill additional decalcifying solution into the
water tank.
again. The display shows CLOSE TAP. Turn the
selector switch (Fig. 3,L) back to the cup symbol MACHINE
DE-SCALING. The machine will now pump the remaining
mixture in intervals into the used water tray inside. After
another 12 minutes the machine "beeps" and the display
shows EMPTY TRAY/EMPTY GROUNDS.
18.3 DECALCIFYING PROCEDURE
SELECT PRODUCT/DE-SCALE MACHINE
10. Carefully remove the used water tray (Fig. 1,18 ), TRAY
MISSING empty it, rinse thoroughly and replace. The display
shows FILL WATER TANK/RINSE WATER TANK.
11. Remove the water tank, rinse thoroughly, fill it halfway with
fresh water and then replace. The display shows
PRESS STEAM.
12. Place a large container under the steam nozzle (Fig. 4).
13. Push either steam button. The display shows MACHINE
DE-SCALING. For 2 minutes, it will pump fresh water in
intervals through the steam nozzle into the container
underneath. Then machine "beeps". The display shows
OPEN TAP.
1. Push and hold the Rinse button until the following message
appears EMPTY TRAY/EMPTY GROUNDS.
2. Remove and empty the tray and the used coffee container
and replace TRAY MISSING.
Attention: If the tray and the used coffee container are
empty, you need to remove the tray for approx. 20 seconds
and then replace it. AGENT IN TANK/PRESS STEAM
3. Empty the Water Container. Remove the Dual Frother.
4. Dissolve 3 of the large square decalcifying tablets in a con-
tainer with 20 oz. of water (0.6 liters) and pour the solution
into the water tank. Replace water tank.
5. Place a large container under the steam nozzle (Fig. 4).
29.
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Empty the container underneath the steam nozzle and
place it underneath the hot water spout (Fig.1,14).
15. Turn the Selector switch to the hot water position (Fig. 3,L).
The machine will now pump fresh water in intervals through
the hot water spout. MACHINE DE-SCALING
or cream from the refrigerator considerably lowers the tempera-
ture of the coffee.
20. ERROR MESSAGES / TROUBLESHOOTING
ERROR MESSAGES:
16. After a short while the machine will beep again. The display
shows CLOSE TAP. Turn the selector switch (Fig. 3,L) back
to the cup symbol. The machine will now pump fresh water
in intervals into the used water tray inside. MACHINE DE-
SCALING. After a short while the machine "beeps" and the
display shows EMPTY TRAY/EMPTY GROUNDS.
17. Carefully remove the used water tray (Fig. 1,18), TRAY MISSING
empty it and replace. The display shows PRESS RINSE.
18. Place a container under the coffee spout and press the
Rinse button. MACHINE RINSING.
The machine can display any of the following error messages:
ERROR 1, ERROR 3, ERROR 5
Call our customer service hot line 1-800-220-5701.
Your machine needs to be returned for service.
ERROR 2, ERROR 4
Your machine is too cold. The heating sensor does not react.
• Turn the machine off.
• Keep the machine at normal room temperature (65º F or
higher) for 2 hours .
• Then turn it on again.
If display still shows ERROR 2 or ERROR 4 call customer
service.
SELECT PRODUCT
The machine will automatically remind you when it’s time to
decalcify again.
ERROR 6, ERROR 7, ERROR 8
• Turn machine off, turn the main power switch off and unplug
machine for a minute.
• Turn machine on again. If the error message comes up again,
try one more time.
19. TIPS FOR BETTER COFFEE
Height adjustable coffee-spout
Adjust the height of the coffee-spout to the size of your cups.
Grinding
Please refer to chapter 7 "Adjusting the Grinder."
Pre-warm cups
• If the message persists, call customer service.
You should warm cups in advance with hot water or steam.
The smaller the quantity of coffee, the more important it is to
warm your cups.
Sugar and cream
Warmth is lost by stirring the contents of the cup. Adding milk
TROUBLESHOOTING:
A. NO COFFEE COMES OUT OF THE COFFEE SPOUT
Reason: Beans in bean container are not feeding properly into
the grinder because they are stuck together.
30.
Download from Www.Somanuals.com. All Manuals Search And Download.
Solution: Stir beans before grinding and while grinding turn the
grinding selector to the coarsest setting.
When using very oily beans pour the beans onto a plate and let
C. INSUFFICIENT FROTHED MILK PRODUCTION
Reason: Milk is initially not cold enough or your milk is not
suited for thick frothing.
some of the sticky oils evaporate (this will not harm the aroma of Solution: Make sure milk is cold. Use a different type of milk.
the coffee).
Skim milk will produce the thickest and longest lasting froth. Full
Reason: You used ground coffee in the ground coffee funnel.
The ground coffee was too fine.
fat milk will produce less thick froth.
Reason: The components of the frother are not assembled
properly, or the components are clogged with hardened milk, or
one or more of the components is missing, or the steam nozzle
is clogged.
Solution: Use ground coffee which is ground somewhat coarser.
Reason: No water is transported through the system.
Solution: Remove water container and make sure that the con-
necting valve is free of any particles (like a coffee bean etc).
Reason: The ground coffee funnel is clogged; the internal brew-
ing chamber is clogged.
Solution: Place a large cup underneath the coffee spout. Push
the rinse button (Fig. 2E) a few times until the blocked coffee is
removed. (Never fill more than 2 scoops of coffee in the ground
coffee funnel; the funnel is not a storage area for ground coffee).
Also, use a ground coffee which is ground somewhat coarser.
Solution:
a. Remove frother. Check that steam comes out of the steam
nozzle. If not, use a needle and clear blockage from inside
steam nozzle.
b. Clean all other frother parts and assemble properly.
See chapters 10b, 10f.
c. If any parts are missing call Customer Service:
1-800-220-5701 or use the enclosed mail order form to order
the missing part.
B. THE DISPLAY READS "FILL WATER" BUT THERE IS
ENOUGH WATER IN THE WATER TANK.
D. GRINDER MAKES AN EXTREMELY LOUD NOISE;
NO BEANS ARE GROUND
Reason: A stone or something else is blocking the burr grinder.
Reason: The low water floatation device (Fig.1,4) is missing.
Solution: Within the water tank is a small compartment (like a
mouse trap). Inside is a small black floatation device. On top is a
small clear see-through plastic cover. This small plastic cover is
missing and the floatation device is outside of the small com-
partment. Check if you can find both pieces inside the water
tank and put it back together. If you cannot find the pieces call
1-800-220-5701. We will send the pieces FREE OF CHARGE.
Solution: See chapter 16.5 and 16.6.
E. THE REMOVABLE DRAWER (Fig.1, 18) DOESN’T COME OUT
Reason: The internal used coffee disposal chute did not retract.
Solution: Turn off the machine. Wait a minute. Turn machine on
and wait until it stops making any noise. Now try to pull out the
drawer. If this does not work, turn the machine off. Now pull the
31.
Download from Www.Somanuals.com. All Manuals Search And Download.
drawer out with some force. You will feel some resistance. When
the drawer is out you will see that the back wall of the used cof-
fee container (Fig.1,16) is missing.
You can order these supplies:
• with the enclosed mail order form or
• by calling our customer service center at 1-800-220-5701.
Reach into the machine and retrieve the back wall (it is a small
black flexible piece). Set the used coffee container aside and
insert the drawer (without the used coffee container) into the
machine. Turn the machine on. Wait until all noise has stopped.
The disposable chute should retract. Remove the drawer,
replace the used coffee container and insert it back into the
machine. Check if the drawer comes out easily.
22. LIMITED WARRANTY
Please note: This warranty will be void if the Warranty / Product
Registration has not been received two weeks after the purchase
date (you can fax or mail the registration or you can register
through our website www.capresso.com)
This limited warranty covers your new IMPRESSA S Avantgarde
Series. For Home and Commercial Use: One Year or 6,000
coffee brewings, whichever comes first.
21. SUPPLIES
The following supplies are necessary to keep your machine in
good working order:
• Clearyl Water Filter Cartridge (one included)
Model #64553; the machine will remind you automatically.
Tip: If you brew 10 cups a day you need about one Clearyl
cartridge per month. Always keep extra cartridges available.
• Special Cleaning Tablets (two included) Model #62205
Tip: If you brew 10 cups a day you need about one tablet
every 3 weeks. Always keep extra tablets available.
• Auto-Cappuccino Cleaner (one bottle included)
Model #63801
This warranty is in effect for the period and usage described
above from the date of the first purchase and is limited to the
United States of America. This warranty covers all defects in
materials or workmanship (parts and labor) including free UPS
ground transportation for both ways within the continental
United States. For Hawaii and Alaska freight is not covered by
this warranty.
TRANSPORT: When sending the machine, use the original pack-
ing materials, the inner and outer cartons or use approximately 2”
of bubblewrap and insert machine in a carton which will hold 40lbs.
Any damage in transit is NOT covered by this warranty.
This warranty does not cover:
Tip: If you use the auto cappuccino cleaner once a day you
need a new bottle every 2 1/2 weeks. Always keep extra
bottles available.
• Decalcifying tablets (large square tablets) - Model #61848
Please note: You must use decalcifying tablets if you do not
use the Clearyl cartridge.
• Any machine NOT distributed by JURA-CAPRESSO within the
United States.
• Any machine not purchased from an Authorized Dealer.
32.
Download from Www.Somanuals.com. All Manuals Search And Download.
• Damage caused by accident, abuse, negligence, misuse,
improper operation or failure to follow instructions contained in
this manual.
• Any service or alteration performed by an unauthorized person,
company or association.
• Damage caused by neglecting and omitting maintenance,
cleaning and decalcifying cycles.
• Damage caused by use of instant coffee or any other ingredients
not allowed in this product.
Other limitations and exclusions:
Any implied warranties including fitness for use and merchantability
are limited in duration to the period of the express warranty set
forth above and no person is authorized to assume for JURA-
CAPRESSO any other liability in connection with the sale of the
machine. JURA-CAPRESSO expressly disclaims liability for
incidental and consequential damages caused by the machine.
The terms "incidental damages" refer to the loss of the original
purchasers time, loss of the use of the machine or other costs
relating to the care and custody of the machine. The terms
"consequential damages" refer to the cost of repairing or replacing
other property which is damaged when this machine does not
work properly. Any loss of income is excluded. The remedies
provided under this warranty are exclusive and in lieu of all others.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
33.
Download from Www.Somanuals.com. All Manuals Search And Download.
Jura-Capresso, LLC
81 Ruckman Road, Closter, NJ 07624
201-767-3999 • Fax: 201-767-9684
Customer Service: 1-800-220-5701
Download from Www.Somanuals.com. All Manuals Search And Download.
|