Two-Knife BookletTrimmer-A1
User's Guide
Please read this guide before operating this product.
After you finish reading this guide, store it in a safe place for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Structure of the Users Guide
Chapter 1
Read here first.
Chapter 2
Chapter 3
Chapter 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
• This manual is designed to help you to install, operate and maintain the trimmer. Please read and under-
stand this manual, and keep it in a safe and convenient place.
• Do not operate the trimmer until you read and understand the instructions in this manual.
• Canon shall not be liable for incidental, consequential damages resulting from: improper or inadequate
maintenance by the customer, unauthorized modification or misuse, or operation outside of the environmen-
tal specifications for the product.
• Canon pursues a policy of continuing improvement in design and performance of the product. Therefore, the
product design and specifications are subject to change without prior notice and without legal obligation.
• All rights are reserved. No part of this manual may be photocopied, reproduced or translated to another lan-
guage without the prior written consent of your local authorized dealer.
• This product applies to the CE Marking.
• This manual describes the operating procedures for the Two-Knife Booklet Trimmer-A1. For trimmer opera-
tions set from the host machine (printer), see the operating manual for the host machine (printer.)
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Safe Use of Machine
To use this machine safely, proper operation and periodic maintenance are indispensable. Read the safety
precautions described in this manual thoroughly, and do not perform operations or maintenance procedures
until you understand them completely.
The operating procedures and safety precautions described in this manual are valid only for proper use of this
machine. Responsibility for any improper use or operation of this machine lies with the user.
Safety precautions are indicated in this manual as follows:
Indicates a warning concerning operations that may lead to death or injury to per-
sons if not performed correctly. In order to use the machine safely, always pay
attention to these warnings.
WARNING
Indicates a caution concerning operations that may lead to injury to persons, or
damage to property if not performed correctly. In order to use the machine safely,
always pay attention to these cautions.
CAUTION
This symbol indicates the range of acceptable values and operating conditions.
This symbol indicates useful supplementary information for operational proce-
dures.
Operating Safety Precautions
WARNING
When moving the machine, be sure to turn off the main power switch on the host machine, then
disconnect the power cord and contact your local authorized dealer. Otherwise, the cord may be
damaged and may result in a fire or electric shock.
Do not remove the safety covers or deactivate the sensor switches for the safety covers. Other-
wise, the machine may start suddenly without warning, leading to severe injury.
CAUTION
When removing jammed booklets from the Infeed section, do not put your hands and fingers close to the
belt. Otherwise, if the belt moves suddenly without warning, your hands and fingers may be caught.
This machine weighs 145 kg (319 lb). When you operate the machine, consider the machine
weight and use the machine safely.
To disconnect the power to this machine, unplug the power plug on the back of the machine.
Do not use paper which does not meet the specifications. Otherwise, it may cause paper jams.
Do not open the covers while machine is operating, or the machine will stop and booklets will jam.
Use this machine only in an office or commercial environment. Do not use this machine in an
industrial environment.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC NOTICES
NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-
ference when the equipment is operated in a commercial environment. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a resi-
dential area is likely to cause harmful interference, in which case the user will be required to correct the
interference at this own expense.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Important Information ...............................................................................................................i
Safe Use of Machine ...............................................................................................................ii
FCC NOTICES .......................................................................................................................iii
Machine Descriptions .......................................................................................................... 1-2
[2] Conveyor Section ...................................................................................................... 1-4
Error Messages ................................................................................................................... 3-2
Service Call Error ........................................................................................................... 3-2
Error Message Chart ...................................................................................................... 3-3
Specifications ...................................................................................................................... 4-2
Specifications ................................................................................................................. 4-2
Index .................................................................................................................................... 4-3
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
1
CHAPTER
Machine Descriptions...........................................................................................................................1-2
Section Descriptions ............................................................................................................................1-3
[1] Two-Knife Trim Section..............................................................................................................1-3
[3] Trim Ejecting Section................................................................................................................. 1-5
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Machine Descriptions
[2]
[3]
[1]
[1] Two-Knife Trim Section (See page 1-3.)
[2] Conveyor Section (See page 1-4.)
[3] Trim Ejecting Section (See page 1-5.)
1-2 Machine Descriptions
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Descriptions
[1] Two-Knife Trim Section
Each booklet delivered from the upstream trimmer is trimmed along its top and bottom, and then
delivered to the conveyor section.
Handle
Top Cover
1
Transport Belts
These belts move
booklets.
Booklet Transport Unit [TF2]
If any booklets jam in the two-knife
trim section, press the handle and lift
up this mechanism to remove the
jammed booklets.
2
Opening the Transport Unit
1. Press the handle to the left.
2. Lift the mechanism up.
Trim Knives
These knives trim top and bot-
tom of each booklet.
Section Descriptions 1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
[2] Conveyor Section
Booklets delivered are laid out on the conveyor.
Handle [TE]
Grip this handle and lift the roller unit when
removing booklets on the conveyor.
Delivery
Transport
Rollers
Output booklets are
held by these rollers.
The position of the
rollers is set automati-
cally to match booklet
sizes.
Booklet Detect
Sensor
This sensor detects
when the conveyor is
full of stacked booklets.
Transport Belts
These belts move booklets after they are
ejected.
*1
Delivery Tray
This tray holds stacked book-
lets. It is removable.
(When the tray is removed, the
conveyor full condition not
detected, and continuous oper-
ation is possible.)
*1 Removing the delivery tray.
1. Loosen two locking knobs.
2. Lift the delivery tray up to remove.
3. Tighten two locking knobs.
Delivery Tray
Locking Knobs
1-4 Section Descriptions
Download from Www.Somanuals.com. All Manuals Search And Download.
[3] Trim Ejecting Section
Trim is ejected into the trim box through this section.
Trim Full Sensor
If trim stacks up between the
sensor and the reflector, the
Trim Full error is indicated.
Delivery
Chute
Trim is ejected into
the trim box through
this chute.
Trim Box
Section Descriptions 1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
1-6 Section Descriptions
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Procedures
2
CHAPTER
Trimmer Setup .....................................................................................................................................2-2
Operation While Trimming ...................................................................................................................2-3
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimmer Setup
1
Turn on the power switch on the saddle stitcher first, then turn on
the power switch on the host machine (printer).
The trimmer will also be powered on as it is connected to the saddle stitcher.
See the operation manual for the printer and set up the printer.
2-2 Trimmer Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation While Trimming
When the conveyor is full of booklets, remove the booklets.
If the machine stops because the conveyor is full, remove the booklets, and operation
restarts automatically.
· If you remove booklets before the conveyor is full, you can increase production
efficiency without interrupting operation.
· Be careful not to drop a booklet while removing it.
Delivery Tray
Trim Box
Trim Full
Sensor
When the trim box is full, empty it.
If the machine stops because the trim box is full, and trim stacks up between the sensor
and the reflector, remove trim, and operation will restart automatically.
· If you remove trim before the trim box is full, you can increase production effi-
ciency without interrupting operation.
Operation While Trimming 2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
If booklets jam, open the cover or mechanism shown below and
remove the jammed booklets.
Top Cover
Transport Section
Delivery Section Cover
Opening the Transport Unit
2
1
1. Press the handle.
2. Hold the handle and lift the unit.
problem.
2-4 Operation While Trimming
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
3
This section describes some possible problems, and suggests some solutions.
CHAPTER
Error Messages....................................................................................................................................3-2
Service Call Error............................................................................................................................3-2
Clearing Paper Jams ...........................................................................................................................3-4
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
If an error occurs and the machine does not work properly, “SERVICE CALL ERROR” appears
on the LCD of the host machine (printer). If “SERVICE CALL ERROR” appears, do the following:
WARNING
Do not plug in or pull out the power plug with wet
hands. This may cause an electrical shock.
CAUTION
When you pull the power plug out, be sure to hold
the plug as you do so. If you pull it out by the power
cable, this may expose or cut the core wires and
break insulation, which may result in fire or electrical
shock.
Service Call Error
If the SERVICE CALL ERROR appears on the LCD of the host machine, turn off the power
switches on the saddle stitcher and the printer. Wait about 10 seconds, and then turn on the
power switches again. If the SERVICE CALL ERROR is still shown on the LCD of the host
machine, check the following items, turn off the main power, and disconnect the power plug on
the two-knife Booklet Trimmer-A1. Then contact your local authorized dealer. Be prepared to
supply the following information:
- Product name
- Type of trouble
- Code number indicated on the touch panel display of the host machine (printer)
3-2 Error Messages
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Message Chart
Follow suggested procedures for the error indicated on the host machine (printer).
E
F2
1
2
A
3
Cause of Error
The top cover is open.
Remedy
Close the top cover 1 .
The conveyor is full.*1
Lift the E handle and remove the booklets from the con-
veyor.
The trim box is full.
Empty it. If there is trim left in the delivery chute, remove
the trim.
A booklet jam has occurred at the Open the delivery section cover 2 of the upstream trim-
1
entrance of the two-knife trim section.
mer and the top cover
mer-A1. Open the
of the two-knife booklet trim-
A and
F2 transport unit, and
remove the jammed booklet. Reposition the
A and
and the
1
F2 transport unit and close the top cover
delivery section cover 2 to restart printing.
A booklet jam has occurred in the two- Open the top cover 1 of the two-knife booklet trimmer-
knife trim section. A1. Open the F2 transport unit and remove the
jammed booklet. Reposition the F2 transport unit and
close the top cover 1 to restart printing.
A booklet jam has occurred at the exit of Open the top cover 1 of the two-knife booklet trimmer-
the two-knife trim section. A1. Open the F2 transport unit and remove the
jammed booklet. If necessary, also hold the E handle
and lift the conveyor. Reposition the E and F2 trans-
1
port unit and close the top cover
to restart printing.
*1
If this error message appears when the conveyor is not full, trim may be blocking the sensor.
Error Messages 3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
Jam in Trim Section
• Paper chip jams. (See pro-
cedure 1.)
• Transport belts are dirty.
(See procedure 2.)
Jam in Conveyor Section
• Paper chip jams. (See proce-
dure 1.)
• Transport belts are dirty. (See
procedure 2.)
F2
E
Procedure 1
Open the transport unit and check to see if there are any paper chips left on the booklet feed
Procedure 2
The transport belts must be cleaned. Contact your local authorized dealer.
3-4 Clearing Paper Jams
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
4
CHAPTER
Specifications.......................................................................................................................................4-2
Index ....................................................................................................................................................4-3
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications
Product Name
Two-Knife Booklet Trimmer-A1
Description of Product
Upper knife reciprocating top-bottom trimmer
Maximum number of sheets
50 sheets (80 gsm),
48 sheets (80 gsm) + 2 sheets (300 gsm)
trimmable *1 *2
Possible trim size *3
Possible trim width
Trim Box Capacity
A3, B4, A4R, 13" x 19.2" (330.2 mm x 487.7 mm), 12" x 18",
11" x 17", LGL, LTRR, 12.60" x 17.72" (320 mm x 450 mm [SRA3])
(Above sizes are native sheet sizes before half folded.)
Top-bottom: 2 to 15 mm (0.08” to 0.59”)
Normally the top-bottom length after trimming should be 190 mm
(7.48”) or larger.
Approximately Trimmed strip from 1,500 sheets (width 15 mm
[0.59"], A4, 80 gsm, approximately 750 sheets on top and bot-
tom respectively)
Conveyor Capacity *4
Machine Dimensions
Weight
30 booklets (40 sheets of A4 booklet, 80 gsm, when trimming
20mm [0.79"] of width in Booklet Trimmer)
536 (W) x 770 (D) x 1,040 (H) mm (21 1/8" x 30 3/8" x 41")
(Without conveyor section and delivery tray)
Approximately 145 kg (319 lb)
(Without conveyor section and delivery tray)
Installation Space with Host Machine
Installation space differs depending on the connected host machine.
Refer to the "Machine Dimension" described on the manual of the
host machine, and this machine.
Voltage
120-127V AC, 50/60Hz, 4A
Power Consumption
Noise Level
440 W or less
70 dBA or less
Environmental
Temperature
in Use
Compliant with the specification of the host machine (printer)
Temperature
in Storage
Temperature
in Transportation
Humidity
-10 to 40°C (14 to 104°F)
-10 to 50°C (14 to 122°F)
Compliant with the specification of the host machine (printer)
608 to 1,013 hPa (18 to 30 in Hg)
Pressure
Contamination
Level
Pollution Degree 2 (Office environment)
*1 If the cover sheet is thinner than the other sheets in the booklet, the cover sheet may be scratched. It is
recommended to use a thicker sheet for the cover sheet.
*2 The maximum number of sheets trimmable can change depending on the connected host machine.
*3 The possible trim size can change depending on the connected host machine.
*4 When the delivery tray is removed, the conveyor full condition is not detected, and continuous operation is
possible.
4-2 Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
|
